期刊文献+

不圆度对圆环和圆管静水压力下临界荷载的影响 被引量:1

Influence of out-of-roundness on the critical loads of circular rings and circular tubes under hydrostatic pressure
在线阅读 下载PDF
导出
摘要 采用最小二乘法求解曲率半径对称波动变化的非理想圆环在均匀静水压力作用下的平面内稳定性问题,分别求得了反对称屈曲和对称屈曲的临界荷载系数。当不圆度参数β=0.4时,反对称屈曲的临界荷载系数降低67.71%。用最小相对误差拟合法得到了精度较高的临界荷载系数拟合公式,其最大相对误差仅为±0.76%。采用平面应变假设,推广得到非理想长圆管在均匀静水压力作用下的临界荷载计算公式,并应用于某工程中长圆钢管的局部稳定性计算,算例中当外径在最大允许外径和公称外径之间波动变化时,临界荷载降低2.58%。 The in-plane buckling problem of a circular ring with symmetric fluctuant radius of curvature under uniform hydrostatic pressure is solved with Least Squares Method, and the critical load coeffi- cients of antisymmetric buckling and symmetric buckling are calculated, respectively. The critical load coefficient of antisymmetric buckling is reduced by 67.71% for out-of-roundness parameter β=0. 4. High precision formulas, the relative errors of which are within ±0. 76%, of the critical load coefficients are obtained by minimum-relative-error data fitting. Based on the plane strain hypothesis, the critical load formulas are extended to a long circular tube with fluctuant radius of curvature under uniform hydrostatic pressure. The formulas are applied to the calculation of local buckling of a long circular steel tube, and the critical load is reduced only by 2.58 % for the diameter fluctuating between the allowable maximum diameter and the nominal diameter.
作者 邓长根
出处 《计算力学学报》 EI CAS CSCD 北大核心 2011年第6期851-857,共7页 Chinese Journal of Computational Mechanics
基金 国家自然科学基金(50478107)资助项目
关键词 圆环 临界荷载 不圆度 静水压力 最小二乘法 circular ring critical load out-of-roundness hydrostatic pressure least squares method
作者简介 邓长根(1962-),男,博士,教授(E-mail:dengcg@tongji.edu.cn).
  • 相关文献

参考文献5

  • 1DinnikAN.拱的稳定性[M].北京:中国建筑工业出版社,1958.
  • 2邓长根.壁厚对称波动圆环在静水压力作用下的临界外压[J].东南大学学报(自然科学版),2011,41(2):347-351. 被引量:2
  • 3中华人民共和国国家标准.GB/T17395-2008无缝钢管尺寸、外形、重量及允许偏差[S].北京:中国标准出版社,2008.
  • 4ENV 1993-1-6. Eurocode 3 Design of Steel Structures, Part 1-6 [S]. Brussels: European Committee for Standardisation, 1999.
  • 5Antaki G A. Piping and Pipeline Engineering : Design, Construction, Maintenance, Integrity, and Repair[M]. New York : Marcel Dekker, 2003.

二级参考文献7

共引文献1

同被引文献6

引证文献1

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部