黄籽油菜因菜油的外观、品质好等优势深受消费者欢迎,但后代性状分离不稳定,严重影响其大面积应用。为解析黄籽油菜性状分离不稳定的内在原因,探寻黄籽油菜中黄色籽粒和黑色籽粒之间内在生理机制存在的差异,以甘蓝型黄籽油菜(CK)为材料...黄籽油菜因菜油的外观、品质好等优势深受消费者欢迎,但后代性状分离不稳定,严重影响其大面积应用。为解析黄籽油菜性状分离不稳定的内在原因,探寻黄籽油菜中黄色籽粒和黑色籽粒之间内在生理机制存在的差异,以甘蓝型黄籽油菜(CK)为材料,对其分离后代中的黄色(Y)、黑色(B)籽粒植株的农艺性状、生理生化指标、种皮颜色相关基因等之间的表达差异开展了研究。结果表明:分离后代中,Y的根茎粗和株高均优于CK和B,B的株高分别与CK、Y呈显著差异,B的根茎粗与Y呈显著差异。Y的病害指数为1.97,CK和B的病害指数分别为2.55,3.33,表明Y在抗病性方面优于CK和B。在9—10叶期Y叶片中的丙二醛(MDA)含量最低,花期Y和CK花中的过氧化物酶(POD)活性持续上升,表明黄籽油菜抗逆能力较强。7—8叶期和9—10叶期B和Y中TT18、TT8基因的表达量均高于CK,终花期B和Y中TT18基因的表达量显著低于CK。授粉后28 d Y种子中MYB47基因的表达量最高,分别为CK的5.56倍和B的5.79倍。TT8基因在授粉后21 d的Y中表达量最高,分别为CK和B的3.30,2.29倍。黄籽油菜在含油量、抗逆等方面均有明显优势,因而大力发展黄籽油菜可为提高菜油供应量,解决我国食用油安全提供新思路。展开更多
Sc_(2)O_(3),as a host for solid-state laser gain materials,has advantage of high thermal conductivity and easy matching with activating ions,which is promising in high-power laser applications.Currently,Yb-doped Sc_(2...Sc_(2)O_(3),as a host for solid-state laser gain materials,has advantage of high thermal conductivity and easy matching with activating ions,which is promising in high-power laser applications.Currently,Yb-doped Sc_(2)O_(3) ceramics have been fabricated at very high sintering temperatures,but their optical quality and sintering process still need further improvement.In this work,5%Yb:Sc_(2)O_(3)(in mass)nano-powders were obtained by co-precipitation,and then transparent ceramics were fabricated by vacuum pre-sintering and hot isostatic pressing(HIP)post-treatment.The cubic Yb:Sc_(2)O_(3) nano-powders with good dispersity and an average crystallite of 29 nm were obtained.Influence of pre-sintering temperatures(1500-1700℃)on densification process,microstructure changes,and optical transmittance of Yb:Sc_(2)O_(3) ceramics was detected.Experimental data revealed that all samples have a uniform microstructure,while the average grain sizes increase with the increase of the sintering temperatures.Impressively,the optimum in-line transmittance of Yb:Sc_(2)O_(3) ceramics,pre-sintered at 1550℃after HIP post-treatment,reaches 78.1%(theoretical value of 80%)at 1100 nm.Spectroscopic properties of the Yb:Sc_(2)O_(3) ceramics reveal that the minimum population inversion parameterβ2 and the luminescence decay time of 5%Yb:Sc_(2)O_(3) ceramics are 0.041 and 0.49 ms,respectively,which demonstrate that the optical quality of the Yb:Sc_(2)O_(3) has been improved.Meanwhile,their best vacuum sintering temperature can be controlled down to a lower temperature(1550℃).In conclusion,Yb:Sc_(2)O_(3) nano-powders are successfully synthesized by co-precipitation method,and good optical quality transparent ceramics are fabricated by vacuum pre-sintering at 1550℃and HIP post-treatment.展开更多
Transparent sand is a special material to realize visualization of concealed work in geotechnical engineering. To investigate the dynamic characteristics of transparent sand, a series of undrained cyclic simple shear ...Transparent sand is a special material to realize visualization of concealed work in geotechnical engineering. To investigate the dynamic characteristics of transparent sand, a series of undrained cyclic simple shear tests were conducted on the saturated transparent sand composed of fused quartz and refractive index-matched oil mixture. The results reveal that an increase in the initial shear stress ratio significantly affects the shape of the hysteresis loop, particularly resulting in more pronounced asymmetrical accumulation. Factors such as lower relative density, higher cyclic stress ratios and higher initial shear stress ratio have been shown to accelerate cyclic deformation, cyclic pore water pressure and stiffness degradation. The cyclic liquefaction resistance curves decrease as the initial shear stress ratio increases or as relative density decreases. Booker model and power law function model were applied to predict the pore water pressure for transparent sand. Both models yielded excellent fits for their respective condition, indicating a similar dynamic liquefaction pattern to that of natural sands. Finally, transparent sand displays similar dynamic characteristics in terms of cyclic liquefaction resistance and Kα correction factor. These comparisons indicate that transparent sand can serve as an effective means to mimic many natural sands in dynamic model tests.展开更多
Er^(3+),Na^(+)co-doped CaF_(2) transparent ceramics with Er^(3+)dopant concentration of 3% and Na^(+) of 0%,0.5%,1.0%,1.5% and 2.0% were fabricated by the vacuum hot pressing method with 16 mm in diameter and 3 mm in ...Er^(3+),Na^(+)co-doped CaF_(2) transparent ceramics with Er^(3+)dopant concentration of 3% and Na^(+) of 0%,0.5%,1.0%,1.5% and 2.0% were fabricated by the vacuum hot pressing method with 16 mm in diameter and 3 mm in thickness.The average grain size of the obtained Er,Na∶CaF_(2) powders varied from 28 nm to 36 nm with the shape of sphere.The effects of Na^(+) doping on the transmittance,microstructure and spectral properties of Er^(3+)∶CaF_(2) transparent ceramics were investigated.The transmittance of all the obtained ceramic samples is above 84%in the wavelength of 1000 nm.The results show that after introducing Na^(+)into Er^(3+)∶CaF_(2) transparent ceramics,charge-neutralized Er^(3+)-Na^(+) structure formed which prevent Er^(3+) from clustering.The emission spectra of Er^(3+) in CaF_(2) transparent ceramics at around 1.5 and 2.7μm could be modulated by adjusting the concentration of Na^(+) and the near-infrared fluorescence lifetime at around 1.5μm increase with the increasing of Na^(+) concentration,reaching a maximum of 56.75 ms.展开更多
(Gd,Lu)_(2)O_(3)∶Eu scintillation ceramics have promising applications in the high-energy X-ray imaging.Eu0.1Gd0.6Lu1.3O3 nano-powders with pure phase were prepared from the precursor calcined at 1050℃for 4 h by the...(Gd,Lu)_(2)O_(3)∶Eu scintillation ceramics have promising applications in the high-energy X-ray imaging.Eu0.1Gd0.6Lu1.3O3 nano-powders with pure phase were prepared from the precursor calcined at 1050℃for 4 h by the co-precipitation method.Using the synthesized nano-powders as initial material,Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics were fabri-cated by vacuum pre-sintering at different temperatures for 2 h and hot isostatic pressing(HIP)at 1750℃for 3 h in ar-gon.The influence of pre-sintering temperature on the microstructure,optical and luminescence properties was investi-gated.The Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics pre-sintered at 1625℃for 2 h combined with HIP post-treatment show the high-est in-line transmittance of 75.2%at 611 nm.The photoluminescence(PL)and X-ray excited luminescence(XEL)spectra of the Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)transparent ceramics demonstrate a strong red emission peak at 611 nm due to the^(5)D_(0)→^(7)F_(2) transition of Eu^(3+).The PL,PLE and XEL intensities of the HIP post-treated Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics show a trend of first ascending and then descending with the increase of pre-sintering temperature.The thermally stimulated lumines-cence(TSL)curve of the HIP post-treated Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics presents one high peak at 178 K and two peaks with lower intensities at 253 K and 320 K.The peak at 320 K may be related to oxygen vacancies,and the lumines-cence peak at 178 K is related to defects caused by the valence state changes of Eu^(3+)ions.展开更多
Three-dimensional(3D) scanning technology has undergone remarkable developments in recent years.Data acquired by 3D scanning have the form of 3D point clouds.The 3D scanned point clouds have data sizes that can be con...Three-dimensional(3D) scanning technology has undergone remarkable developments in recent years.Data acquired by 3D scanning have the form of 3D point clouds.The 3D scanned point clouds have data sizes that can be considered big data.They also contain measurement noise inherent in measurement data.These properties of 3D scanned point clouds make many traditional CG/visualization techniques difficult.This paper reviewed our recent achievements in developing varieties of high-quality visualizations suitable for the visual analysis of 3D scanned point clouds.We demonstrated the effectiveness of the method by applying the visualizations to various cultural heritage objects.The main visualization targets used in this paper are the floats in the Gion Festival in Kyoto(the float parade is on the UNESCO Intangible Cultural Heritage List) and Borobudur Temple in Indonesia(a UNESCO World Heritage Site).展开更多
A small-scale physical modelling method was developed to investigate the pile bearing capacity and the soil displacement around the pile using transparent soil and particle image velocimetry(PIV) technique. Transparen...A small-scale physical modelling method was developed to investigate the pile bearing capacity and the soil displacement around the pile using transparent soil and particle image velocimetry(PIV) technique. Transparent sand was made of baked quartz and a pore fluid with a matching refractive index. The physical modelling system consists of a loading system, a laser light, a CCD camera, an optical platform and a computer for image analyzing. A distinctive laser speckle was generated by the interaction between the laser light and transparent soil. Two laser speckle images before and after deformation were used to calculate the soil displacement field using PIV. Two pipe piles with different diameters under oblique pullout loads at angles of 0°, 30°, 45°, 60° and 90° were used in tests. The load-displacement response, oblique pullout ultimate resistances and soil displacement fields were then studied. The test results show that the developed physical modelling method and transparent soil are suitable for pile-soil interaction problems. The soil displacements around the pipe piles will improve the understanding on the capacity of pipe piles under oblique pullout loads.展开更多
The waste dump of open-pit coal mine is remade of soil-rock mixture under the action of gravity,dynamic load of transportation equipment and earthquake,etc.By using artificial synthetic transparent soil,the developing...The waste dump of open-pit coal mine is remade of soil-rock mixture under the action of gravity,dynamic load of transportation equipment and earthquake,etc.By using artificial synthetic transparent soil,the developing process and migration law for soil-rock mixture are observed in the remade process.The mixture of fused quartz sand,liquid paraffin and n-tridecane is chosen as the material for synthetic transparent soil which is mixed with liquid paraffin and n-tridecane at a mass ratio of4.4at room temperature of17℃.Physical and mechanical properties of transparent soil are determined by physical test and compared with those in natural sandy soil.The results show that transparent soil and sandy soil have high similarity,in other words,transparent soil can be used for similar simulation experiments of soil-rock mixture.展开更多
In this paper,we proposed a new design scheme of real time electronic countermeasure simulation system.This paper mainly expounds the modeling and realization methods of each part of the whole simulation system,and th...In this paper,we proposed a new design scheme of real time electronic countermeasure simulation system.This paper mainly expounds the modeling and realization methods of each part of the whole simulation system,and the real-time property of system has been lucubrated.Electronic countermeasure simulation system is the key part of military training of individuals;it can also allow the realistic evaluation of the performance of modern equipments and techniques.As a proof,we have drawn up a series of simulation scenarios,such as radar electronic reconnaissance simulation scenario,to explain the feasibility and the superiority of our modeling scheme in this paper.展开更多
A novel device, lateral PIN photodiode gated by transparent electrode （LPIN PD-GTE） fabricated on fully-depleted SOI film was proposed. ITO film was adopted in the device as gate electrode to reduce the light absorp...A novel device, lateral PIN photodiode gated by transparent electrode （LPIN PD-GTE） fabricated on fully-depleted SOI film was proposed. ITO film was adopted in the device as gate electrode to reduce the light absorption. Thin Si film was fully depleted under gate voltage to achieve low dark current and high photo4o-dark current ratio. The model of gate voltage was obtained and the numerical simulations were presented by ATLAS. Current-voltage characteristics of LPIN PD-GTE obtained in dark （dark current） and under 570 nm illumination （photo current） were studied to achieve the greatest photo-to-dark current ratio for active channel length from 2 to 12 /am. The results show that the photo-to-dark current ratio is 2.0×10^7, with dark current of around 5×10^-4 pA under VGK=0.6 V, PrN=5 mW/cm2, for a total area of 10μm×10μm in fully depleted SOI technology. Thus, the LPIN PD-GTE can be suitable for high-grade photoelectric systems such as blue DVD.展开更多
Fluorine doped tin oxide SnO2：F thin films were prepared by the spray pyrolysis （SP） technique on glass substrates by using SnC12.2H2O as a precursor and NH4F and HF as doping compounds. A comparison between the pr...Fluorine doped tin oxide SnO2：F thin films were prepared by the spray pyrolysis （SP） technique on glass substrates by using SnC12.2H2O as a precursor and NH4F and HF as doping compounds. A comparison between the properties of the films obtained by using the two doping compounds was performed by using I-V characteristics in the dark at room temperature, AC measurements, and transmittance. It is found that the films prepared by using HF have smaller resistivity, lower impedance and they are less capacitive than films prepared by using NH4F. In addition, these films have higher transmittance, higher optical bandgap energy and narrower Urbach tail width. These results are interesting for the use of SnO2：F as forecontact in CdS/CdTe solar cells.展开更多
The precursor powders of LuAG∶Ce3+ transparent ceramics were synthesized by solvo-thermal method.The crystal structure and morphology of powders were analyzed by means of Fourier transform infra-red spectroscopy,X-ra...The precursor powders of LuAG∶Ce3+ transparent ceramics were synthesized by solvo-thermal method.The crystal structure and morphology of powders were analyzed by means of Fourier transform infra-red spectroscopy,X-ray diffraction and scanning electron microscopy.The precursor powders were sintered into transparent ceramics in vacuum and then in nitrogen without any additive.The surface morphology of the transparent unpolished ceramics was characterized using scanning electron microscopy.Some factors that affect the transparency of ceramics were discussed.The UV-Vis fluorescence excitation and emission spectra of LuAG∶Ce3+ transparent ceramics were measured.The vacuum ultraviolet spectra of transparent ceramics were investigated using the synchrotron radiation as the excitation source.The excitation mechanism of Ce3+ was discussed at different excitation wavelength.展开更多
YAG (Y_(3)Al_(5)O_(12)) transparent ceramics have attractive application prospects for transparent armor protection modules because of their excellent light transmittance and anti-ballistic capability. Understanding t...YAG (Y_(3)Al_(5)O_(12)) transparent ceramics have attractive application prospects for transparent armor protection modules because of their excellent light transmittance and anti-ballistic capability. Understanding the fracture behavior and damage mechanism of YAG is necessary for armor design. To explore the damage characteristics of YAG under compression and tension, shock compression and shockless spalling experiments with soft recovery technique are conducted. The spall strength of YAG is obtained and the recovered samples are observed by CT and SEM. It is shown that the macroscopic damage characteristic of YAG under compression is vertical split cracks with oblique fine cracks distributed in the entire sample, while that under tension is horizontal transgranular cracks concentrated near the main spall surface. The cracks generated by macroscopic compression, tension and shear stress extend in similar tensile form at the microscale. The proportion of transgranular fractures on spall surfaces is higher than that of cracks induced by macroscopic compression. Meanwhile, higher loading rate and longer loading duration increase the transgranular fracture percentage.展开更多
Specific to the reflected light problem on the surface of transparent body,the polarization characteristics of the reflection region are analyzed,and a polarization characterization model combining the reflection and ...Specific to the reflected light problem on the surface of transparent body,the polarization characteristics of the reflection region are analyzed,and a polarization characterization model combining the reflection and transmission effects is established.On the basis of the polarization characteristic analysis,the minimum value of normalized cross-correlation(NCC)coefficient between transmission and reflection images is solved through the gradient descent method,and their polarization degrees under the minimum correlation are acquired.According to the distribution relations of the transmitted and reflected lights in perpendicular and parallel directions,reflection separation is realized via the polarized orthogonality difference algorithm based on the degree of reflection polarization and the degree of transmission polarization.展开更多
Crystal of barium boric oxide(BBO) crystallizes in trigollal system. Imperfections in two specimens of(001)plates (one being transparent and the other containing inclusions)in the crystals have been identified by X-ra...Crystal of barium boric oxide(BBO) crystallizes in trigollal system. Imperfections in two specimens of(001)plates (one being transparent and the other containing inclusions)in the crystals have been identified by X-ray topography.展开更多
文摘黄籽油菜因菜油的外观、品质好等优势深受消费者欢迎,但后代性状分离不稳定,严重影响其大面积应用。为解析黄籽油菜性状分离不稳定的内在原因,探寻黄籽油菜中黄色籽粒和黑色籽粒之间内在生理机制存在的差异,以甘蓝型黄籽油菜(CK)为材料,对其分离后代中的黄色(Y)、黑色(B)籽粒植株的农艺性状、生理生化指标、种皮颜色相关基因等之间的表达差异开展了研究。结果表明:分离后代中,Y的根茎粗和株高均优于CK和B,B的株高分别与CK、Y呈显著差异,B的根茎粗与Y呈显著差异。Y的病害指数为1.97,CK和B的病害指数分别为2.55,3.33,表明Y在抗病性方面优于CK和B。在9—10叶期Y叶片中的丙二醛(MDA)含量最低,花期Y和CK花中的过氧化物酶(POD)活性持续上升,表明黄籽油菜抗逆能力较强。7—8叶期和9—10叶期B和Y中TT18、TT8基因的表达量均高于CK,终花期B和Y中TT18基因的表达量显著低于CK。授粉后28 d Y种子中MYB47基因的表达量最高,分别为CK的5.56倍和B的5.79倍。TT8基因在授粉后21 d的Y中表达量最高,分别为CK和B的3.30,2.29倍。黄籽油菜在含油量、抗逆等方面均有明显优势,因而大力发展黄籽油菜可为提高菜油供应量,解决我国食用油安全提供新思路。
基金National Key R&D Program of China(2023YFE3812005)International Partnership Program of Chinese Academy of Sciences(121631KYSB20200039)+1 种基金National Center for Research and Development(WPC2/1/SCAPOL/2021)Chinese Academy of Sciences President’s International Fellowship Initiative(2024VEA0005,2024VEA0014)。
文摘Sc_(2)O_(3),as a host for solid-state laser gain materials,has advantage of high thermal conductivity and easy matching with activating ions,which is promising in high-power laser applications.Currently,Yb-doped Sc_(2)O_(3) ceramics have been fabricated at very high sintering temperatures,but their optical quality and sintering process still need further improvement.In this work,5%Yb:Sc_(2)O_(3)(in mass)nano-powders were obtained by co-precipitation,and then transparent ceramics were fabricated by vacuum pre-sintering and hot isostatic pressing(HIP)post-treatment.The cubic Yb:Sc_(2)O_(3) nano-powders with good dispersity and an average crystallite of 29 nm were obtained.Influence of pre-sintering temperatures(1500-1700℃)on densification process,microstructure changes,and optical transmittance of Yb:Sc_(2)O_(3) ceramics was detected.Experimental data revealed that all samples have a uniform microstructure,while the average grain sizes increase with the increase of the sintering temperatures.Impressively,the optimum in-line transmittance of Yb:Sc_(2)O_(3) ceramics,pre-sintered at 1550℃after HIP post-treatment,reaches 78.1%(theoretical value of 80%)at 1100 nm.Spectroscopic properties of the Yb:Sc_(2)O_(3) ceramics reveal that the minimum population inversion parameterβ2 and the luminescence decay time of 5%Yb:Sc_(2)O_(3) ceramics are 0.041 and 0.49 ms,respectively,which demonstrate that the optical quality of the Yb:Sc_(2)O_(3) has been improved.Meanwhile,their best vacuum sintering temperature can be controlled down to a lower temperature(1550℃).In conclusion,Yb:Sc_(2)O_(3) nano-powders are successfully synthesized by co-precipitation method,and good optical quality transparent ceramics are fabricated by vacuum pre-sintering at 1550℃and HIP post-treatment.
基金Project(U2268213) supported by the National Natural Science Foundation of ChinaProject(2024YFHZ0121) supported by the Sichuan Science and Technology Program,China。
文摘Transparent sand is a special material to realize visualization of concealed work in geotechnical engineering. To investigate the dynamic characteristics of transparent sand, a series of undrained cyclic simple shear tests were conducted on the saturated transparent sand composed of fused quartz and refractive index-matched oil mixture. The results reveal that an increase in the initial shear stress ratio significantly affects the shape of the hysteresis loop, particularly resulting in more pronounced asymmetrical accumulation. Factors such as lower relative density, higher cyclic stress ratios and higher initial shear stress ratio have been shown to accelerate cyclic deformation, cyclic pore water pressure and stiffness degradation. The cyclic liquefaction resistance curves decrease as the initial shear stress ratio increases or as relative density decreases. Booker model and power law function model were applied to predict the pore water pressure for transparent sand. Both models yielded excellent fits for their respective condition, indicating a similar dynamic liquefaction pattern to that of natural sands. Finally, transparent sand displays similar dynamic characteristics in terms of cyclic liquefaction resistance and Kα correction factor. These comparisons indicate that transparent sand can serve as an effective means to mimic many natural sands in dynamic model tests.
基金National Key R&D Program of China(2023YFB3507400)。
文摘Er^(3+),Na^(+)co-doped CaF_(2) transparent ceramics with Er^(3+)dopant concentration of 3% and Na^(+) of 0%,0.5%,1.0%,1.5% and 2.0% were fabricated by the vacuum hot pressing method with 16 mm in diameter and 3 mm in thickness.The average grain size of the obtained Er,Na∶CaF_(2) powders varied from 28 nm to 36 nm with the shape of sphere.The effects of Na^(+) doping on the transmittance,microstructure and spectral properties of Er^(3+)∶CaF_(2) transparent ceramics were investigated.The transmittance of all the obtained ceramic samples is above 84%in the wavelength of 1000 nm.The results show that after introducing Na^(+)into Er^(3+)∶CaF_(2) transparent ceramics,charge-neutralized Er^(3+)-Na^(+) structure formed which prevent Er^(3+) from clustering.The emission spectra of Er^(3+) in CaF_(2) transparent ceramics at around 1.5 and 2.7μm could be modulated by adjusting the concentration of Na^(+) and the near-infrared fluorescence lifetime at around 1.5μm increase with the increasing of Na^(+) concentration,reaching a maximum of 56.75 ms.
文摘(Gd,Lu)_(2)O_(3)∶Eu scintillation ceramics have promising applications in the high-energy X-ray imaging.Eu0.1Gd0.6Lu1.3O3 nano-powders with pure phase were prepared from the precursor calcined at 1050℃for 4 h by the co-precipitation method.Using the synthesized nano-powders as initial material,Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics were fabri-cated by vacuum pre-sintering at different temperatures for 2 h and hot isostatic pressing(HIP)at 1750℃for 3 h in ar-gon.The influence of pre-sintering temperature on the microstructure,optical and luminescence properties was investi-gated.The Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics pre-sintered at 1625℃for 2 h combined with HIP post-treatment show the high-est in-line transmittance of 75.2%at 611 nm.The photoluminescence(PL)and X-ray excited luminescence(XEL)spectra of the Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)transparent ceramics demonstrate a strong red emission peak at 611 nm due to the^(5)D_(0)→^(7)F_(2) transition of Eu^(3+).The PL,PLE and XEL intensities of the HIP post-treated Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics show a trend of first ascending and then descending with the increase of pre-sintering temperature.The thermally stimulated lumines-cence(TSL)curve of the HIP post-treated Eu_(0.1)Gd_(0.6)Lu_(1.3)O_(3)ceramics presents one high peak at 178 K and two peaks with lower intensities at 253 K and 320 K.The peak at 320 K may be related to oxygen vacancies,and the lumines-cence peak at 178 K is related to defects caused by the valence state changes of Eu^(3+)ions.
文摘Three-dimensional(3D) scanning technology has undergone remarkable developments in recent years.Data acquired by 3D scanning have the form of 3D point clouds.The 3D scanned point clouds have data sizes that can be considered big data.They also contain measurement noise inherent in measurement data.These properties of 3D scanned point clouds make many traditional CG/visualization techniques difficult.This paper reviewed our recent achievements in developing varieties of high-quality visualizations suitable for the visual analysis of 3D scanned point clouds.We demonstrated the effectiveness of the method by applying the visualizations to various cultural heritage objects.The main visualization targets used in this paper are the floats in the Gion Festival in Kyoto(the float parade is on the UNESCO Intangible Cultural Heritage List) and Borobudur Temple in Indonesia(a UNESCO World Heritage Site).
基金Project(51478165)supported by the National Natural Science Foundation of ChinaProject(2013B31814+1 种基金2014B07214)supported by the Fundamental Research Funds for the Central UniversitiesChina
文摘A small-scale physical modelling method was developed to investigate the pile bearing capacity and the soil displacement around the pile using transparent soil and particle image velocimetry(PIV) technique. Transparent sand was made of baked quartz and a pore fluid with a matching refractive index. The physical modelling system consists of a loading system, a laser light, a CCD camera, an optical platform and a computer for image analyzing. A distinctive laser speckle was generated by the interaction between the laser light and transparent soil. Two laser speckle images before and after deformation were used to calculate the soil displacement field using PIV. Two pipe piles with different diameters under oblique pullout loads at angles of 0°, 30°, 45°, 60° and 90° were used in tests. The load-displacement response, oblique pullout ultimate resistances and soil displacement fields were then studied. The test results show that the developed physical modelling method and transparent soil are suitable for pile-soil interaction problems. The soil displacements around the pipe piles will improve the understanding on the capacity of pipe piles under oblique pullout loads.
基金Project(2015QNA40)supported by the Fundamental Research Funds for the Central Universities,China
文摘The waste dump of open-pit coal mine is remade of soil-rock mixture under the action of gravity,dynamic load of transportation equipment and earthquake,etc.By using artificial synthetic transparent soil,the developing process and migration law for soil-rock mixture are observed in the remade process.The mixture of fused quartz sand,liquid paraffin and n-tridecane is chosen as the material for synthetic transparent soil which is mixed with liquid paraffin and n-tridecane at a mass ratio of4.4at room temperature of17℃.Physical and mechanical properties of transparent soil are determined by physical test and compared with those in natural sandy soil.The results show that transparent soil and sandy soil have high similarity,in other words,transparent soil can be used for similar simulation experiments of soil-rock mixture.
基金supported by Scientific Research Program Funded by Shaanxi Provincial Education Department(Program No.18JK0286)Weinan Science and Technology Initiatives Fund program(Program No.2019JCYJ-2-6)+2 种基金Teaching Reform Project of Weinan Normal University(Program No.JG201704)Industry-University-Cooperation Education Project of the Ministry of Education of China(Program No.201702030020,201801082110)Weinan Normal University's Characteristic Discipline Construction Project Electronic Information(Computer Technology)Master's Degree Point Construction Project(18TSXK06)。
文摘In this paper,we proposed a new design scheme of real time electronic countermeasure simulation system.This paper mainly expounds the modeling and realization methods of each part of the whole simulation system,and the real-time property of system has been lucubrated.Electronic countermeasure simulation system is the key part of military training of individuals;it can also allow the realistic evaluation of the performance of modern equipments and techniques.As a proof,we have drawn up a series of simulation scenarios,such as radar electronic reconnaissance simulation scenario,to explain the feasibility and the superiority of our modeling scheme in this paper.
基金Project(61040061) supported by the National Natural Science Foundation of ChinaProject supported by Hunan Provincial Innovation Foundation for Postgraduate Students,China
文摘A novel device, lateral PIN photodiode gated by transparent electrode （LPIN PD-GTE） fabricated on fully-depleted SOI film was proposed. ITO film was adopted in the device as gate electrode to reduce the light absorption. Thin Si film was fully depleted under gate voltage to achieve low dark current and high photo4o-dark current ratio. The model of gate voltage was obtained and the numerical simulations were presented by ATLAS. Current-voltage characteristics of LPIN PD-GTE obtained in dark （dark current） and under 570 nm illumination （photo current） were studied to achieve the greatest photo-to-dark current ratio for active channel length from 2 to 12 /am. The results show that the photo-to-dark current ratio is 2.0×10^7, with dark current of around 5×10^-4 pA under VGK=0.6 V, PrN=5 mW/cm2, for a total area of 10μm×10μm in fully depleted SOI technology. Thus, the LPIN PD-GTE can be suitable for high-grade photoelectric systems such as blue DVD.
文摘Fluorine doped tin oxide SnO2：F thin films were prepared by the spray pyrolysis （SP） technique on glass substrates by using SnC12.2H2O as a precursor and NH4F and HF as doping compounds. A comparison between the properties of the films obtained by using the two doping compounds was performed by using I-V characteristics in the dark at room temperature, AC measurements, and transmittance. It is found that the films prepared by using HF have smaller resistivity, lower impedance and they are less capacitive than films prepared by using NH4F. In addition, these films have higher transmittance, higher optical bandgap energy and narrower Urbach tail width. These results are interesting for the use of SnO2：F as forecontact in CdS/CdTe solar cells.
基金Project supported by National Nature Science Foundation of China(10774140)Knowledge Innovation Project of The Chinese Academy of Sciences(KJCX2-YW-M11)+1 种基金Specialized Research Fund for the Doctoral Program of Higher Education(20060358054)Special Foundation for Talents of Anhui Province,China(2007Z021)
文摘The precursor powders of LuAG∶Ce3+ transparent ceramics were synthesized by solvo-thermal method.The crystal structure and morphology of powders were analyzed by means of Fourier transform infra-red spectroscopy,X-ray diffraction and scanning electron microscopy.The precursor powders were sintered into transparent ceramics in vacuum and then in nitrogen without any additive.The surface morphology of the transparent unpolished ceramics was characterized using scanning electron microscopy.Some factors that affect the transparency of ceramics were discussed.The UV-Vis fluorescence excitation and emission spectra of LuAG∶Ce3+ transparent ceramics were measured.The vacuum ultraviolet spectra of transparent ceramics were investigated using the synchrotron radiation as the excitation source.The excitation mechanism of Ce3+ was discussed at different excitation wavelength.
基金This work is funded by the National Natural Science Foundation of China(No.11772159)the NSAF Joint Fund(No.U1730101)the Fundamental Research Funds for the Central Universities(No.30917011104).
文摘YAG (Y_(3)Al_(5)O_(12)) transparent ceramics have attractive application prospects for transparent armor protection modules because of their excellent light transmittance and anti-ballistic capability. Understanding the fracture behavior and damage mechanism of YAG is necessary for armor design. To explore the damage characteristics of YAG under compression and tension, shock compression and shockless spalling experiments with soft recovery technique are conducted. The spall strength of YAG is obtained and the recovered samples are observed by CT and SEM. It is shown that the macroscopic damage characteristic of YAG under compression is vertical split cracks with oblique fine cracks distributed in the entire sample, while that under tension is horizontal transgranular cracks concentrated near the main spall surface. The cracks generated by macroscopic compression, tension and shear stress extend in similar tensile form at the microscale. The proportion of transgranular fractures on spall surfaces is higher than that of cracks induced by macroscopic compression. Meanwhile, higher loading rate and longer loading duration increase the transgranular fracture percentage.
基金supported by the National Natural Science Foundation of China(62075239,61302145).
文摘Specific to the reflected light problem on the surface of transparent body,the polarization characteristics of the reflection region are analyzed,and a polarization characterization model combining the reflection and transmission effects is established.On the basis of the polarization characteristic analysis,the minimum value of normalized cross-correlation(NCC)coefficient between transmission and reflection images is solved through the gradient descent method,and their polarization degrees under the minimum correlation are acquired.According to the distribution relations of the transmitted and reflected lights in perpendicular and parallel directions,reflection separation is realized via the polarized orthogonality difference algorithm based on the degree of reflection polarization and the degree of transmission polarization.
文摘Crystal of barium boric oxide(BBO) crystallizes in trigollal system. Imperfections in two specimens of(001)plates (one being transparent and the other containing inclusions)in the crystals have been identified by X-ray topography.
