With its commercialization, the second-generation(2G) high temperature superconducting(HTS) RE–Ba–Cu–O(REBCO, RE is rare earth) tape is extensively applied to the superconducting magnets in the high magnetic fields...With its commercialization, the second-generation(2G) high temperature superconducting(HTS) RE–Ba–Cu–O(REBCO, RE is rare earth) tape is extensively applied to the superconducting magnets in the high magnetic fields. However,unlike low temperature superconducting(LTS) magnets, the HTS magnet cannot operate in the persistent current mode(PCM) due to the immature superconducting soldering technique. In this paper, an exciting method for two HTS sub-loops,so-called charging and load loops, is proposed by flux pump consisting of exciting coil and controllable thermal switch.Two HTS sub-loops are made of an REBCO tape with two slits. An exciting coil with iron core is located in one sub-loop and is supplied with a triangular waveform current so that magnetic field is generated in another sub-loop. The influence of magnetic flux on induced current in load loop is presented and verified in experiment at 77 K. The relationship between the induced magnetic flux density and the current on the sub-loops having been calibrated, magnetic flux density, and induced current are obtained. The results show that the HTS sub-loops can be excited by a coil with thermal switch and the induced current increases with magnetic flux of exciting coil increasing, which is promising for persistent current operation mode of HTS magnets.展开更多
In this study, a novel self-embedding asymmetric stepped impedance resonator （SE-ASIR） topology is proposed. By embedding asymmetric stepped impedance resonators in themselves, circuit sizes of ASIRs can be reduced ...In this study, a novel self-embedding asymmetric stepped impedance resonator （SE-ASIR） topology is proposed. By embedding asymmetric stepped impedance resonators in themselves, circuit sizes of ASIRs can be reduced effectively, while the ability to control spurious modes of ASIRs remains. Therefore, SE-ASIRs are suitable for being used to design filters with wide stopbands and miniaturized sizes. Furthermore, the construction process of the SE-ASIR is described in detail, and an equivalent model of the SE-ASIR is proposed. For demonstration, a high-temperature superconducting bandpass filter centered at 1112 MHz is designed and fabricated. The measured result agrees well with the simulation result and shows that the out-of-band rejection is better than 60 dB up to 4088 MHz, which is about 3.7 times the center frequency. The filter circuit size is 31 mm × 13 mm or 0.28λg × 0.12λg, where g is the guided wavelength at 1112 MHz.展开更多
High temperature superconducting （HTS） power inductor and its control technology have been studied and analyzed in the paper. Based on the results of simulations and practical experiments, a controlled release schem...High temperature superconducting （HTS） power inductor and its control technology have been studied and analyzed in the paper. Based on the results of simulations and practical experiments, a controlled release scheme has been proposed and verified for developing a practical HTS SMES prototype.展开更多
Silver-clad （Bi,Pb）2Sr2Ca2Cu3O10＋x long wires produced by powder-in-tube techniques, which have been recognized as the first generation of the High Temperature Superconducting （HTS） wires, are expected to apply w...Silver-clad （Bi,Pb）2Sr2Ca2Cu3O10＋x long wires produced by powder-in-tube techniques, which have been recognized as the first generation of the High Temperature Superconducting （HTS） wires, are expected to apply widely especially in strong current applications. In this work, the processing, characterization and application of the silver-clad （Bi,Pb）2Sr2Ca2Cu3Ol0＋x HTS wires are summarized. The HTS wires are fabricated using the combination of powder-in-tube technique, and the resulting wires are fully characterized by the means of chemical analyses, microstructural observation, electrical and magnetic measurements. The relationship among fabrication parameters, chemical and microstructural characteristics, and electrical and magnetic properties are analyzed. Applications of the HTS wires have also been introduced according to their strong current behaviors with various prototype devices made.展开更多
Stationary long pulse plasma of high electron temperature was produced on EAST for the first time through an integrated control of plasma shape, divertor heat flux, particle exhaust, wall conditioning, impurity manage...Stationary long pulse plasma of high electron temperature was produced on EAST for the first time through an integrated control of plasma shape, divertor heat flux, particle exhaust, wall conditioning, impurity management, and the coupling of multiple heating and current drive power. A discharge with a lower single null divertor configuration was maintained for 103 s at a plasma current of 0.4 MA, q95 ≈7.0, a peak electron temperature of 〉4.5 keV, and a central density ne（0）-2.5×10^19 m^-3. The plasma current was nearly non-inductive （Vloop 〈0.05 V, poloidal beta - 0.9） driven by a combination of 0.6 MW lower hybrid wave at 2.45 GHz, 1.4 MW lower hybrid wave at 4.6 GHz, 0.5 MW electron cyclotron heating at 140 GHz, and 0.4 MW modulated neutral deuterium beam injected at 60 kV. This progress demonstrated strong synergy of electron cyclotron and lower hybrid electron heating, current drive, and energy confinement of stationary plasma on EAST. It further introduced an example of integrated ＂hybrid＂ operating scenario of interest to ITER and CFETR.展开更多
The effect of an initially grown high-temperature A1N buffer （HT-A1N） layer＇s thickness on the quality of an A1N epilayer grown on sapphire substrate by metalorganic chemical vapor deposition （MOCVD） in a two-ste...The effect of an initially grown high-temperature A1N buffer （HT-A1N） layer＇s thickness on the quality of an A1N epilayer grown on sapphire substrate by metalorganic chemical vapor deposition （MOCVD） in a two-step growth process is investigated. The characteristics of A1N epilayers are analyzed by using triple-axis crystal X-ray diffraction （XRD） and atomic force microscopy （AFM）. It is shown that the crystal quality of the A1N epilayer is closely related to its correlation length. The correlation length is determined by the thickness of the initially grown HT-A1N buffer layer. We find that the optimal HT-A1N buffer thickness for obtaining a high-quality A1N epilayer grown on sapphire substrate is about 20 nm.展开更多
After discovering high temperature superconducting materials 20 years ago, the preparation of applicable HTS materials has been pursued along with HTS mechanism and characteristic study. At present, the focus on the a...After discovering high temperature superconducting materials 20 years ago, the preparation of applicable HTS materials has been pursued along with HTS mechanism and characteristic study. At present, the focus on the applied HTS technology has been moving to the industrial preparations from the laboratory research stage, and the technology has been well verified for practical applications from small to large scales. The fabrication techniques of engineering HTS materials are being industrialized; and various HTS devices are also on the way towards practical applications. This paper provides a comprehensive summary on the applied high temperature superconductivity with regard to various applicable HTS materials, their preparation techniques and charac- terization, and applications in a wide range.展开更多
We briefly introduce a new high-pressure transport measurement system integrated with low temperature and magnetic field that is being established as one of the user experimental stations of the Synergetic Extreme Con...We briefly introduce a new high-pressure transport measurement system integrated with low temperature and magnetic field that is being established as one of the user experimental stations of the Synergetic Extreme Condition User Facilities in the Huairou District of Beijing, China. To demonstrate the capabilities of the system for condensed matter research, the emergence of some pressure-induced phenomena and physics related to superconductivity found previously is also introduced, and then a perspective for such an advanced high-pressure system is presented.展开更多
CSIRO has had a long-term research effort in superconductivity, in particular, since the discovery of HTS which promised big prospects. Significant progress has been made in research and development of HTS electronic ...CSIRO has had a long-term research effort in superconductivity, in particular, since the discovery of HTS which promised big prospects. Significant progress has been made in research and development of HTS electronic devices and systems for practical applications such as mineral and exploration as well as some niche applications in emerging science and technology areas. This article presents an overview of the CSIRO research activities in HTS supercon- ducting electronics since 1987, outlining the HTS junction and device technology as well as various application systems developed by the group.展开更多
In this paper, we present a compact quint-band superconducting filter operating at 2.4, 3.5, 4.7, 5.3, and 5.9 GHz.Matching junctions with different impedance branch lines are used to connect a dual-band sub-filter wi...In this paper, we present a compact quint-band superconducting filter operating at 2.4, 3.5, 4.7, 5.3, and 5.9 GHz.Matching junctions with different impedance branch lines are used to connect a dual-band sub-filter with a tri-band sub-filter and to reduce the channel interactions. The quint-band filter design is divided into two sections to determine the controllable frequencies and bandwidths, while ensuring compact size and reducing design complexity. The filter is fabricated on double-sided YBCO film deposited on an Mg O substrate with a size of 26 mm×19 mm. The measured results match well with the simulations.展开更多
Twenty years after the discovery of hightemperature superconductors （HTSs）, the HTS materials now have been well developed. Meanwhile the mechanism of superconductivity is still one of the topical interests in physi...Twenty years after the discovery of hightemperature superconductors （HTSs）, the HTS materials now have been well developed. Meanwhile the mechanism of superconductivity is still one of the topical interests in physics. The achievements made on HTS materials and theories during the last twenty years are reviewed comprehensively in this paper.展开更多
Journal of Electronic Science and Technology of China (JESTC) invites manuscript submissions in the area of High Temperature Superconductivity (HTS). This special issue of
Submission Deadline: 15 February 2008 Journal of Electronic Science and Technology of China (JESTC) invites manuscript submissions in the area of High Temperature Superconductivity (HTS). This special issue of JESTC w...Submission Deadline: 15 February 2008 Journal of Electronic Science and Technology of China (JESTC) invites manuscript submissions in the area of High Temperature Superconductivity (HTS). This special issue of JESTC will focus on recent experiment, theoretical, and application progress in HTS. It is intended to highlight and summarize the major developments that have occurred over the past few years. Topic scopes related to HTS to be covered include:展开更多
基金Project supported by the National Natural Science Foundation of China (Grant No. 51977078)。
文摘With its commercialization, the second-generation(2G) high temperature superconducting(HTS) RE–Ba–Cu–O(REBCO, RE is rare earth) tape is extensively applied to the superconducting magnets in the high magnetic fields. However,unlike low temperature superconducting(LTS) magnets, the HTS magnet cannot operate in the persistent current mode(PCM) due to the immature superconducting soldering technique. In this paper, an exciting method for two HTS sub-loops,so-called charging and load loops, is proposed by flux pump consisting of exciting coil and controllable thermal switch.Two HTS sub-loops are made of an REBCO tape with two slits. An exciting coil with iron core is located in one sub-loop and is supplied with a triangular waveform current so that magnetic field is generated in another sub-loop. The influence of magnetic flux on induced current in load loop is presented and verified in experiment at 77 K. The relationship between the induced magnetic flux density and the current on the sub-loops having been calibrated, magnetic flux density, and induced current are obtained. The results show that the HTS sub-loops can be excited by a coil with thermal switch and the induced current increases with magnetic flux of exciting coil increasing, which is promising for persistent current operation mode of HTS magnets.
基金supported by the National Natural Science Foundation of China(Grant No.61371009)the National High Technology Research and Development Program of China(Grant No.2014AA032703)
文摘In this study, a novel self-embedding asymmetric stepped impedance resonator （SE-ASIR） topology is proposed. By embedding asymmetric stepped impedance resonators in themselves, circuit sizes of ASIRs can be reduced effectively, while the ability to control spurious modes of ASIRs remains. Therefore, SE-ASIRs are suitable for being used to design filters with wide stopbands and miniaturized sizes. Furthermore, the construction process of the SE-ASIR is described in detail, and an equivalent model of the SE-ASIR is proposed. For demonstration, a high-temperature superconducting bandpass filter centered at 1112 MHz is designed and fabricated. The measured result agrees well with the simulation result and shows that the out-of-band rejection is better than 60 dB up to 4088 MHz, which is about 3.7 times the center frequency. The filter circuit size is 31 mm × 13 mm or 0.28λg × 0.12λg, where g is the guided wavelength at 1112 MHz.
文摘High temperature superconducting （HTS） power inductor and its control technology have been studied and analyzed in the paper. Based on the results of simulations and practical experiments, a controlled release scheme has been proposed and verified for developing a practical HTS SMES prototype.
文摘Silver-clad （Bi,Pb）2Sr2Ca2Cu3O10＋x long wires produced by powder-in-tube techniques, which have been recognized as the first generation of the High Temperature Superconducting （HTS） wires, are expected to apply widely especially in strong current applications. In this work, the processing, characterization and application of the silver-clad （Bi,Pb）2Sr2Ca2Cu3Ol0＋x HTS wires are summarized. The HTS wires are fabricated using the combination of powder-in-tube technique, and the resulting wires are fully characterized by the means of chemical analyses, microstructural observation, electrical and magnetic measurements. The relationship among fabrication parameters, chemical and microstructural characteristics, and electrical and magnetic properties are analyzed. Applications of the HTS wires have also been introduced according to their strong current behaviors with various prototype devices made.
基金supported by the National Magnetic Confinement Fusion Science Foundation of China(Nos.2015GB102000 and 2014GB103000)
文摘Stationary long pulse plasma of high electron temperature was produced on EAST for the first time through an integrated control of plasma shape, divertor heat flux, particle exhaust, wall conditioning, impurity management, and the coupling of multiple heating and current drive power. A discharge with a lower single null divertor configuration was maintained for 103 s at a plasma current of 0.4 MA, q95 ≈7.0, a peak electron temperature of 〉4.5 keV, and a central density ne（0）-2.5×10^19 m^-3. The plasma current was nearly non-inductive （Vloop 〈0.05 V, poloidal beta - 0.9） driven by a combination of 0.6 MW lower hybrid wave at 2.45 GHz, 1.4 MW lower hybrid wave at 4.6 GHz, 0.5 MW electron cyclotron heating at 140 GHz, and 0.4 MW modulated neutral deuterium beam injected at 60 kV. This progress demonstrated strong synergy of electron cyclotron and lower hybrid electron heating, current drive, and energy confinement of stationary plasma on EAST. It further introduced an example of integrated ＂hybrid＂ operating scenario of interest to ITER and CFETR.
基金Project supported by the National Natural Science Foundation of China (Grant No. 60876009)
文摘The effect of an initially grown high-temperature A1N buffer （HT-A1N） layer＇s thickness on the quality of an A1N epilayer grown on sapphire substrate by metalorganic chemical vapor deposition （MOCVD） in a two-step growth process is investigated. The characteristics of A1N epilayers are analyzed by using triple-axis crystal X-ray diffraction （XRD） and atomic force microscopy （AFM）. It is shown that the crystal quality of the A1N epilayer is closely related to its correlation length. The correlation length is determined by the thickness of the initially grown HT-A1N buffer layer. We find that the optimal HT-A1N buffer thickness for obtaining a high-quality A1N epilayer grown on sapphire substrate is about 20 nm.
文摘After discovering high temperature superconducting materials 20 years ago, the preparation of applicable HTS materials has been pursued along with HTS mechanism and characteristic study. At present, the focus on the applied HTS technology has been moving to the industrial preparations from the laboratory research stage, and the technology has been well verified for practical applications from small to large scales. The fabrication techniques of engineering HTS materials are being industrialized; and various HTS devices are also on the way towards practical applications. This paper provides a comprehensive summary on the applied high temperature superconductivity with regard to various applicable HTS materials, their preparation techniques and charac- terization, and applications in a wide range.
文摘We briefly introduce a new high-pressure transport measurement system integrated with low temperature and magnetic field that is being established as one of the user experimental stations of the Synergetic Extreme Condition User Facilities in the Huairou District of Beijing, China. To demonstrate the capabilities of the system for condensed matter research, the emergence of some pressure-induced phenomena and physics related to superconductivity found previously is also introduced, and then a perspective for such an advanced high-pressure system is presented.
文摘CSIRO has had a long-term research effort in superconductivity, in particular, since the discovery of HTS which promised big prospects. Significant progress has been made in research and development of HTS electronic devices and systems for practical applications such as mineral and exploration as well as some niche applications in emerging science and technology areas. This article presents an overview of the CSIRO research activities in HTS supercon- ducting electronics since 1987, outlining the HTS junction and device technology as well as various application systems developed by the group.
基金supported by the National Natural Science Foundation of China(Grant Nos.61371009 and 61401282)the National Key Scientific Instrument and Equipment Development Project of China(Grant No.2014YQ030975)
文摘In this paper, we present a compact quint-band superconducting filter operating at 2.4, 3.5, 4.7, 5.3, and 5.9 GHz.Matching junctions with different impedance branch lines are used to connect a dual-band sub-filter with a tri-band sub-filter and to reduce the channel interactions. The quint-band filter design is divided into two sections to determine the controllable frequencies and bandwidths, while ensuring compact size and reducing design complexity. The filter is fabricated on double-sided YBCO film deposited on an Mg O substrate with a size of 26 mm×19 mm. The measured results match well with the simulations.
文摘Twenty years after the discovery of hightemperature superconductors （HTSs）, the HTS materials now have been well developed. Meanwhile the mechanism of superconductivity is still one of the topical interests in physics. The achievements made on HTS materials and theories during the last twenty years are reviewed comprehensively in this paper.
文摘Journal of Electronic Science and Technology of China (JESTC) invites manuscript submissions in the area of High Temperature Superconductivity (HTS). This special issue of
文摘Submission Deadline: 15 February 2008 Journal of Electronic Science and Technology of China (JESTC) invites manuscript submissions in the area of High Temperature Superconductivity (HTS). This special issue of JESTC will focus on recent experiment, theoretical, and application progress in HTS. It is intended to highlight and summarize the major developments that have occurred over the past few years. Topic scopes related to HTS to be covered include:
