Based on the stress distribution characteristics of rock burst multiple sites, the criterion of horizontal stress inducing layer dislocation rock burst was established. Accordingly, the influencing factors were analyz...Based on the stress distribution characteristics of rock burst multiple sites, the criterion of horizontal stress inducing layer dislocation rock burst was established. Accordingly, the influencing factors were analyzed. The analysis results indicate that the stress condition, edge of etastic zone depth, supporting strength, and the friction angle and cohesion among coal stratum, roof and floor are sensitive factors. By introducing double-couple model, the layer dislocation rock burst was explained and the energy radiation characteristics were analyzed. The SOS micro-seismic monitoring system was applied to observe the rock burst hazards about a mining face. The results show that P- and S-wave energy radiations produced by rock burst have directional characteristics. The energy radiation characteristics of the 22 rock bursts occurring on 79Z6 long-wall face are basically the same as theoretical results, that is, the ratio of S-wave energy of sensor 4 to 6 is about 1.5 and that of P-wave is smaller than 0.5. The consistency of the monitored characteristics of the energy radiation theoretically increases with the total energy increasing.展开更多
In this study, the laminar heat transfer and nanofluid flow between two porous horizontal concentric cylinders was investigated. The problem is investigated in two different geometries and the Re=10, 25, 50, 75, 100 a...In this study, the laminar heat transfer and nanofluid flow between two porous horizontal concentric cylinders was investigated. The problem is investigated in two different geometries and the Re=10, 25, 50, 75, 100 and volume fraction 0, 0.2%, 0.5%, 2% and 5% that related to copper nanoparticles, and porous medium porosity of 0.5 and 0.9. Compared to the first geometry, the convective coefficient in the second geometry increases by 8.3%, 7% and 5.5% at Reynolds numbers of 100, 75 and 50, respectively. Comparison of the outlet temperatures for two heat fluxes of 300 and 1200 W/m^2 indicates a 2.5% temperature growth by a fourfold increase in the heat fluxes. Also, the higher Nusselt number is associated with the second geometry occurring at porosities of 0.9 and 0.5, respectively. In both geometries, the Nusselt number values at the porosity of 0.9 are higher, which is due to the increased nanofluid convection at higher porosities. The velocity of the nanofluid experiences a two-fold increase at the outlet compared to its inlet velocity in the first geometry and for both porosities. Similarly, a three-fold increase was achieved in the second geometry and for both porosities.展开更多
For the backfill hydraulic support as the key equipment for achieving integration of backfilling and coal mining simultaneously in the practical process, its characteristics will directly influence the backfill body&#...For the backfill hydraulic support as the key equipment for achieving integration of backfilling and coal mining simultaneously in the practical process, its characteristics will directly influence the backfill body's compression ratio. Horizontal roof gap, as a key parameter of backfilling characteristics, may impact the backfilling effect from the aspects of control of roof subsidence in advance, support stress, backfilling process and the support design. Firstly, the reason why horizontal roof gap exists was analyzed and its definition, causes and connotation were introduced, then adopting the Pro/E 3D simulation software, three typical 3D entity models of backfill hydraulic supports were built, based on the influence of horizontal roof gap on backfilling effect, and influence rules of four factors, i.e. support height, suspension height, suspension angle and tamping angle, were emphatically analyzed on horizontal roof gap. The results indicate that, the four factors all have significant impacts on horizontal roof gap, but show differences in influence trend and degree, showing negative linear correlation, positive linear correlation, positive semi-parabolic correlation and negative semi-parabolic correlation, respectively. Four legs type is the most adaptive to the four factors, while six legs(II) type has the poorest adaptability, and the horizontal roof gap is small under large support height, small suspension height, small suspension angle and large tamping angle situation. By means of optimizing structure components and their positional relation and suspension height of backfill scrape conveyor in the process of support design and through controlling working face deployment, roof subsidence in advance, mining height and backfilling during engineering application, the horizontal roof gap is optimized. The research results can be served as theoretical basis for support design and guidance for backfill support to have better performance in backfilling.展开更多
Production decline analysis has been considered as an important method to obtain the flow parameters, reservoir properties and original gas in place. Although advanced Blasingame production decline analysis methods fo...Production decline analysis has been considered as an important method to obtain the flow parameters, reservoir properties and original gas in place. Although advanced Blasingame production decline analysis methods for vertical wells, fractured wells and horizontal wells are widely used, limited study has conducted on Blasingame production decline type curves for multi-fractured horizontal well(MFHW). Based on the perpendicular bisection(PEBI) grids, a numerical model was developed and the solution was obtained using control volume finite element method and the fully implicit method. Blasingame production decline-type curves of the infinitely conductive MFHW were plotted through computer programming. A field case was presented to analyse and verify the model developed. Five flow regimes, including early formation linear flow, early radial flow, compound linear flow, transient flow and pseudo-radial flow, are recognized. Fracture spacing is the main factor that affects early radial flow, compound linear flow and transient flow, the distance from the well to the circular boundary affects the pseudo-radial flow, and the type curves are also significantly affected by the formation permeability, fracture number and fracture half-length. The validation of field case suggests that the Blasingame production decline type curves proposed in this work can be applied to the production decline analysis for MFHW in tight gas reservoirs.展开更多
In the view of the problems existing in horizontal well,such as sand depositing and cleaning difficulty of borehole,a technology with rotating jet suitable to resolution of the problems was presented.Based on liquid s...In the view of the problems existing in horizontal well,such as sand depositing and cleaning difficulty of borehole,a technology with rotating jet suitable to resolution of the problems was presented.Based on liquid solid two-phase flow theory,the analyses on the sand movement law and the swirling field influential factors were conducted.Results show that:1) With the increasing of displacement in horizontal section annulus,swirling field strength increases,and when the displacement is constant,the closer from the nozzle,the stronger the swirling field strength is;2) Head rotating speed and liquid viscosity have little influence on the swirling field strength,but the sand-carrying rate of fluid can increase by increasing liquid viscosity in a certain range;3) Rotating the string and reducing its eccentricity in annulus are conducive for sand migration in the annulus;4) The sand can be suspended and accelerated again and the swirling field strength is enhanced by the helix agitator.Hence,the research results provide the theoretical basis for the design and application of rotating jet tool.展开更多
Dimensional analysis and numerical simulations were carried out to research prediction method of breakthrough time of horizontal wells in bottom water reservoir. Four dimensionless independent variables and dimensionl...Dimensional analysis and numerical simulations were carried out to research prediction method of breakthrough time of horizontal wells in bottom water reservoir. Four dimensionless independent variables and dimensionless time were derived from 10 influencing factors of the problem by using dimensional analysis. Simulations of horizontal well in reservoir with bottom water were run to find the prediction correlation. A general and concise functional relationship for predicting breakthrough time was established based on simulation results and theoretical analysis. The breakthrough time of one conceptual model predicted by the correlation is very close to the result by Eclipse with less than 2% error. The practical breakthrough time of one well in Helder oilfield is 10 d, and the predicted results by the method is 11.2 d, which is more accurate than the analytical result. Case study indicates that the method could predict breakthrough time of horizontal well under different reservoir conditions accurately. For its university and ease of use, the method is suitable for quick prediction of breakthrough time.展开更多
It is well-known that barriers have a significant impact on the production performance of horizontal wells developed in a bottom water drive reservoir. In most cases, reservoir barriers are semi-permeable. Based on pr...It is well-known that barriers have a significant impact on the production performance of horizontal wells developed in a bottom water drive reservoir. In most cases, reservoir barriers are semi-permeable. Based on previous research on impermeable reservoir barrier, a mathematical flow model was derived for a horizontal well of a bottom water drive reservoir with a semi-permeable barrier. Besides, analytical equations were also presented to calculate critical parameters, such as production rate,pressure and potential difference. The effects of barrier, well and reservoir parameters on our model results were further investigated.The results show that the larger the barrier size is or the higher the barrier location is, the higher the critical production rate and potential difference of a horizontal well are. When the barrier permeability equals the formation permeability or the barrier width equals zero, the critical production rates converge to the values same to that of the case with no barrier. When the barrier permeability equals zero, the problem is regarded as a case of impermeable barrier. This model can be applied to predicting horizontal wells' critical production parameters in reservoirs with semi-permeable barriers.展开更多
The horizontal block stripe,as an image quality defect,was analyzed by means of output signals and bias voltage stress(BVS)test.The results showed that the defect was correlated with discharging efficiency.Further,two...The horizontal block stripe,as an image quality defect,was analyzed by means of output signals and bias voltage stress(BVS)test.The results showed that the defect was correlated with discharging efficiency.Further,two approaches were proposed,one was to improve TFT characteristic,the other was to add reset function.The combined experiments indicated that discharging promotion can improve the defect.Especially the latter is most optimal to eliminate the phenomenon.展开更多
Faulted gas reservoirs are very common in reality,where some linear leaky faults divide the gas reservoir into several reservoir regions with distinct physical properties.This kind of gas reservoirs is also known as l...Faulted gas reservoirs are very common in reality,where some linear leaky faults divide the gas reservoir into several reservoir regions with distinct physical properties.This kind of gas reservoirs is also known as linear composite(LC)gas reservoirs.Although some analytical/semi-analytical models have been proposed to investigate pressure behaviors of producing wells in LC reservoirs based on the linear composite ideas,almost all of them focus on vertical wells and studies on multiple fractured horizontal wells are rare.After the pressure wave arrives at the leaky fault,pressure behaviors of multiple fractured horizontal wells will be affected by the leaky faults.Understanding the effect of leaky faults on pressure behaviors of multiple fractured horizontal wells is critical to the development design.Therefore,a semi-analytical model of finite-conductivity multiple fractured horizontal(FCMFH)wells in LC gas reservoirs is established based on Laplace-space superposition principle and fracture discrete method.The proposed model is validated against commercial numerical simulator.Type curves are obtained to study pressure characteristics and identify flow regimes.The effects of some parameters on type curves are discussed.The proposed model will have a profound effect on developing analytical/semi-analytical models for other complex well types in LC gas reservoirs.展开更多
Effects of the flow pattern of intertubular liquid film on mass and heat transfer synergies in a falling-film dehumidification system with horizontal pipes are studied.A flow model of the dehumidifying solution betwee...Effects of the flow pattern of intertubular liquid film on mass and heat transfer synergies in a falling-film dehumidification system with horizontal pipes are studied.A flow model of the dehumidifying solution between horizontal pipes is established using Fluent software,the rule of transitions of the flow pattern between pipes is studied,critical Reynolds numbers of flow pattern transitions are obtained,and the accuracy of the model is verified by experiments.The mass transfer synergy angle and heat transfer synergy angle are respectively used as evaluation criteria for the mass transfer synergy and heat transfer synergy,and distribution laws of the synergy angles for droplet,droplet columnar and curtain flow patterns are obtained.Simulation results show that the mass transfer synergy angles corresponding to droplet,droplet columnar and curtain flow patterns all rise to a plateau with time.The mean mass-transfer synergy angle is 98°for the droplet flow pattern,higher than 96.5°for the droplet columnar flow pattern and 95°for the curtain flow pattern.The results show that the mass transfer synergy of the droplet flow pattern is better than that of the droplet columnar flow pattern and that of the curtain flow pattern.展开更多
In this study a 10-storied residential building model was employed to clarify the ventilation characteristics of the atrium and the rooms,which were effected by the different forms of lateral openings.The experiment w...In this study a 10-storied residential building model was employed to clarify the ventilation characteristics of the atrium and the rooms,which were effected by the different forms of lateral openings.The experiment was conducted under the combined effect of wind force and thermal buoyancy,and the similarity requirements were satisfied.The results have shown that the different forms of lateral openings cause the different ventilation effect of the building,and also have some certain regularity.The conclusions provide a theoretical foundation for how to use the ventilation of atrium better in high-rise residential building.展开更多
Road horizontal alignment contains three elements: straight line,circular arc,and clothoid.In AutoCAD,clothoid can only be fitted by polyline or spline,and the graphics which are separated from the road data are indep...Road horizontal alignment contains three elements: straight line,circular arc,and clothoid.In AutoCAD,clothoid can only be fitted by polyline or spline,and the graphics which are separated from the road data are independent of each other.Therefore,it is necessary to develop a new curve for road horizontal alignment.Firstly,the differential approximation and series integration methods for clothoid were discussed.Secondly,the geometric formulae for road line which contain the three elements were derived as a whole.Then,the advantages and feasibility of customizing a road line class,which was derived from the curve base class,were analyzed based on ObjectARX(AutoCAD Runtime eXtension) techniques.Finally,the data structure and operations for the road line class were stressed.The experimental results show that the road line can integrate the road elements,graphics and data to implement the graphics-oriented design,which can be widely used in road alignment design.展开更多
Backlash nonlinearity inevitably exists in the actuator of tank horizontal stabilizer and has adverse effect on the system control performance,however,how to effectively eliminate its effect remains a pending issue.To...Backlash nonlinearity inevitably exists in the actuator of tank horizontal stabilizer and has adverse effect on the system control performance,however,how to effectively eliminate its effect remains a pending issue.To solve this problem,a robust adaptive precision motion controller is presented in this paper to address uncertainties and unknown actuator backlash of tank horizontal actuator.The controller handles the modeling uncertainties including parameter uncertainties and unmodeled disturbances by integrating adaptive feedforward compensation and continuous nonlinear robust law.Based on the backstepping method,a smooth backlash inverse model is constructed by combining the adaptive idea.Meanwhile,the unknown backlash parameters of the system can be approximated through the parameter adaptation,and the impact of the actuator backlash nonlinearity is effectively compensated via the inverse operation,which can availably improve the tracking performance.Moreover,the adaptive law can update the disturbance ranges of tank horizontal stabilizer online in real time,which enhances the feasibility in practical engineering applications.Furthermore,the stability analysis based on Lyapunov function shows that with the existence of unmodeled disturbances and unknown actuator backlash,the designed controller guarantees excellent asymptotic output tracking performance.Extensive comparative results verify the effectiveness of the proposed control strategy.展开更多
Based on reliability theory,a general method for the optimization design of piles subjected to horizontal loads is presented.This method takes into consideration various uncertainties caused by pile installation,varia...Based on reliability theory,a general method for the optimization design of piles subjected to horizontal loads is presented.This method takes into consideration various uncertainties caused by pile installation,variability of geotechnical materials from one location to another,and so on.It also deals with behavior and side constraints specified by standard specifications for piles.To more accurately solve the optimization design model,the first order reliability method is employed.The results from the numerical example indicate that the target reliability index has significant influence on design parameters.In addition,the optimization weight increases with the target reliability index.Especially when the target reliability index is relatively large,the target reliability index has significant influence on design weight of piles.展开更多
This paper presents an approach to the challenging is- sue of passive source localization in shallow water using a mobile short horizontal linear array with length less than ten meters. The short array can be convenie...This paper presents an approach to the challenging is- sue of passive source localization in shallow water using a mobile short horizontal linear array with length less than ten meters. The short array can be conveniently placed on autonomous underwa- ter vehicles and deployed for adaptive spatial sampling. However, the use of such small aperture passive sonar systems makes it difficult to acquire sufficient spatial gain for localizing long-range sources. To meet the requirement, a localization approach that employs matched-field based techniques that enable the short ho- rizontal linear array is used to passively localize acoustic sources in shallow water. Furthermore, the broadband processing and inter-position processing provide robustness against ocean en- vironmental mismatch and enhance the stability of the estimation process. The proposed approach＇s ability to localize acoustic sources in shallow water at different signal-to-noise ratios is examined through the synthetic test cases where the sources are located at the endfire and some other bearing of the mobile short horizontal linear array. The presented results demonstrate that the positional parameters of the estimated source build up over time as the array moves at a low speed along a straight line at a constant depth.展开更多
Based on a dual-polarization high-frequency wave radar system, an adaptive system using horizontal antennas for the suppression of the Es layer interference （ELI） is deseribech The data received from the horizontal ...Based on a dual-polarization high-frequency wave radar system, an adaptive system using horizontal antennas for the suppression of the Es layer interference （ELI） is deseribech The data received from the horizontal antennas were correlated with the data received from the Vertically Polarized Antennas （VPAs） to estimate and cancel the interference adaptively in the VPAs. Suppressing the interference after each coherent integration time interval, about 25 dB signal-to-interference ratio is expected with the experimentally derived data.展开更多
Based on theory of variable-mass system thermodynamics, the dynamic mathematic models of each component of the horizontal steam-launch system were established, and by the numerical simulation of the system launching p...Based on theory of variable-mass system thermodynamics, the dynamic mathematic models of each component of the horizontal steam-launch system were established, and by the numerical simulation of the system launching process, the thermodynamics and kinetics characteristics of the system with three valves of different flow characteristics were got. The simulation results show that the values of the peak-to-average ratios of dimensionless acceleration with the equal percentage valve, the linear valve and the quick opening valve are 1.355, 1.614 and 1.722, respectively, and the final values of the dimensionless velocities are 0.843, 0.957 and 1.0, respectively. In conclusion, the value of the dimensionless velocity with the equal percentage valve doesn't reach the set value of 0.90 when the dimensionless displacement is 0.82, while the system with the linear valve can meet the launching requirement, as well as the fluctuation range of dimensionless acceleration is less than that of the quick opening valve. Therefore, the system with the linear valve has the best performance among the three kinds of valves.展开更多
The main structure and working principle of the single-shaft horizontal total mixed ration mixer was discussed. For studying the mixing principle, the analysis of force and motion of the material on the paddle were ma...The main structure and working principle of the single-shaft horizontal total mixed ration mixer was discussed. For studying the mixing principle, the analysis of force and motion of the material on the paddle were made, and paddle angle and rotational speed of the rotor were determined by the experiment, the main mixing ways were explained.展开更多
In slab column-shear wall structures,both the whole structure′s seismic behavior and failure mode are greatly influenced by the distribution of horizontal seismic forces between slab-column and shear wall.In this pap...In slab column-shear wall structures,both the whole structure′s seismic behavior and failure mode are greatly influenced by the distribution of horizontal seismic forces between slab-column and shear wall.In this paper,a pushover analysis of topical slab column-shear wall structure was carried out,the seismic shear force that the slab-column and shear wall should undertake was worked out,the influences of plastic internal force redistribution and structure stiffness characteristic value on horizontal seismic distribution were studied and the calculation formula was given.The analysis results showed that with the yield of the shear walls,the story shear force was undertaken by slab-columns correspondingly increased while with the decrease of characteristic value of stiffness of a structure,and the horizontal seismic force was undertaken by slab-columns correspondingly decreased.According to the code,the design of horizontal force distribution may be cause insecurity problems,so it is necessary to give the distribution law of horizontal seismic forces in slab-column shear wall structures as the supplement to the corresponding regulation of the Code.展开更多
基金Project(2012LWB63) supported by the Fundamental Research Funds for the Central Universities, ChinaProject(SZBF2011-6-B35) supported by the Priority Acadamic Program Development of Jiangsu Higher Education Institutions (PAPD),China
文摘Based on the stress distribution characteristics of rock burst multiple sites, the criterion of horizontal stress inducing layer dislocation rock burst was established. Accordingly, the influencing factors were analyzed. The analysis results indicate that the stress condition, edge of etastic zone depth, supporting strength, and the friction angle and cohesion among coal stratum, roof and floor are sensitive factors. By introducing double-couple model, the layer dislocation rock burst was explained and the energy radiation characteristics were analyzed. The SOS micro-seismic monitoring system was applied to observe the rock burst hazards about a mining face. The results show that P- and S-wave energy radiations produced by rock burst have directional characteristics. The energy radiation characteristics of the 22 rock bursts occurring on 79Z6 long-wall face are basically the same as theoretical results, that is, the ratio of S-wave energy of sensor 4 to 6 is about 1.5 and that of P-wave is smaller than 0.5. The consistency of the monitored characteristics of the energy radiation theoretically increases with the total energy increasing.
文摘In this study, the laminar heat transfer and nanofluid flow between two porous horizontal concentric cylinders was investigated. The problem is investigated in two different geometries and the Re=10, 25, 50, 75, 100 and volume fraction 0, 0.2%, 0.5%, 2% and 5% that related to copper nanoparticles, and porous medium porosity of 0.5 and 0.9. Compared to the first geometry, the convective coefficient in the second geometry increases by 8.3%, 7% and 5.5% at Reynolds numbers of 100, 75 and 50, respectively. Comparison of the outlet temperatures for two heat fluxes of 300 and 1200 W/m^2 indicates a 2.5% temperature growth by a fourfold increase in the heat fluxes. Also, the higher Nusselt number is associated with the second geometry occurring at porosities of 0.9 and 0.5, respectively. In both geometries, the Nusselt number values at the porosity of 0.9 are higher, which is due to the increased nanofluid convection at higher porosities. The velocity of the nanofluid experiences a two-fold increase at the outlet compared to its inlet velocity in the first geometry and for both porosities. Similarly, a three-fold increase was achieved in the second geometry and for both porosities.
基金Project(2014ZDPY02) supported by the Fundamental Research Funds for the Central Universities,ChinaProject supported by Qinglan Plan of Jiangsu Province,ChinaProject(SKLCRSM12X01) supported by State Key Laboratory of Coal Resources and Safe Mining(China University of Mining & Technology)
文摘For the backfill hydraulic support as the key equipment for achieving integration of backfilling and coal mining simultaneously in the practical process, its characteristics will directly influence the backfill body's compression ratio. Horizontal roof gap, as a key parameter of backfilling characteristics, may impact the backfilling effect from the aspects of control of roof subsidence in advance, support stress, backfilling process and the support design. Firstly, the reason why horizontal roof gap exists was analyzed and its definition, causes and connotation were introduced, then adopting the Pro/E 3D simulation software, three typical 3D entity models of backfill hydraulic supports were built, based on the influence of horizontal roof gap on backfilling effect, and influence rules of four factors, i.e. support height, suspension height, suspension angle and tamping angle, were emphatically analyzed on horizontal roof gap. The results indicate that, the four factors all have significant impacts on horizontal roof gap, but show differences in influence trend and degree, showing negative linear correlation, positive linear correlation, positive semi-parabolic correlation and negative semi-parabolic correlation, respectively. Four legs type is the most adaptive to the four factors, while six legs(II) type has the poorest adaptability, and the horizontal roof gap is small under large support height, small suspension height, small suspension angle and large tamping angle situation. By means of optimizing structure components and their positional relation and suspension height of backfill scrape conveyor in the process of support design and through controlling working face deployment, roof subsidence in advance, mining height and backfilling during engineering application, the horizontal roof gap is optimized. The research results can be served as theoretical basis for support design and guidance for backfill support to have better performance in backfilling.
基金Project(2013CB228005)supported by the National Basic Research Program of China
文摘Production decline analysis has been considered as an important method to obtain the flow parameters, reservoir properties and original gas in place. Although advanced Blasingame production decline analysis methods for vertical wells, fractured wells and horizontal wells are widely used, limited study has conducted on Blasingame production decline type curves for multi-fractured horizontal well(MFHW). Based on the perpendicular bisection(PEBI) grids, a numerical model was developed and the solution was obtained using control volume finite element method and the fully implicit method. Blasingame production decline-type curves of the infinitely conductive MFHW were plotted through computer programming. A field case was presented to analyse and verify the model developed. Five flow regimes, including early formation linear flow, early radial flow, compound linear flow, transient flow and pseudo-radial flow, are recognized. Fracture spacing is the main factor that affects early radial flow, compound linear flow and transient flow, the distance from the well to the circular boundary affects the pseudo-radial flow, and the type curves are also significantly affected by the formation permeability, fracture number and fracture half-length. The validation of field case suggests that the Blasingame production decline type curves proposed in this work can be applied to the production decline analysis for MFHW in tight gas reservoirs.
基金Projects(51004082,51222406)supported by the National Natural Science Foundation of ChinaProject(NCET-12-1061)supported by the New Century Excellent Talents in University of ChinaProjects(12TD007,2011JQ0020)supported by Scientific Research Innovation Team Project of Sichuan and the Sichuan Youth Sci-tech Fund,China
文摘In the view of the problems existing in horizontal well,such as sand depositing and cleaning difficulty of borehole,a technology with rotating jet suitable to resolution of the problems was presented.Based on liquid solid two-phase flow theory,the analyses on the sand movement law and the swirling field influential factors were conducted.Results show that:1) With the increasing of displacement in horizontal section annulus,swirling field strength increases,and when the displacement is constant,the closer from the nozzle,the stronger the swirling field strength is;2) Head rotating speed and liquid viscosity have little influence on the swirling field strength,but the sand-carrying rate of fluid can increase by increasing liquid viscosity in a certain range;3) Rotating the string and reducing its eccentricity in annulus are conducive for sand migration in the annulus;4) The sand can be suspended and accelerated again and the swirling field strength is enhanced by the helix agitator.Hence,the research results provide the theoretical basis for the design and application of rotating jet tool.
基金Project(2011ZX05009-004)supported by the National Science and Technology Major Projects of China
文摘Dimensional analysis and numerical simulations were carried out to research prediction method of breakthrough time of horizontal wells in bottom water reservoir. Four dimensionless independent variables and dimensionless time were derived from 10 influencing factors of the problem by using dimensional analysis. Simulations of horizontal well in reservoir with bottom water were run to find the prediction correlation. A general and concise functional relationship for predicting breakthrough time was established based on simulation results and theoretical analysis. The breakthrough time of one conceptual model predicted by the correlation is very close to the result by Eclipse with less than 2% error. The practical breakthrough time of one well in Helder oilfield is 10 d, and the predicted results by the method is 11.2 d, which is more accurate than the analytical result. Case study indicates that the method could predict breakthrough time of horizontal well under different reservoir conditions accurately. For its university and ease of use, the method is suitable for quick prediction of breakthrough time.
基金Project(51404201)supported by the National Natural Science Foundation of ChinaProject(2011ZX05024-003)supported by the National Science and Technology Major Project of China+1 种基金Project(14ZB0045)supported by the Scientific Project of Sichuan Provincial Education Department,ChinaProject(2015JY0076)supported by Basic Application Research of Science and Technology Department of Sichuan Province,China
文摘It is well-known that barriers have a significant impact on the production performance of horizontal wells developed in a bottom water drive reservoir. In most cases, reservoir barriers are semi-permeable. Based on previous research on impermeable reservoir barrier, a mathematical flow model was derived for a horizontal well of a bottom water drive reservoir with a semi-permeable barrier. Besides, analytical equations were also presented to calculate critical parameters, such as production rate,pressure and potential difference. The effects of barrier, well and reservoir parameters on our model results were further investigated.The results show that the larger the barrier size is or the higher the barrier location is, the higher the critical production rate and potential difference of a horizontal well are. When the barrier permeability equals the formation permeability or the barrier width equals zero, the critical production rates converge to the values same to that of the case with no barrier. When the barrier permeability equals zero, the problem is regarded as a case of impermeable barrier. This model can be applied to predicting horizontal wells' critical production parameters in reservoirs with semi-permeable barriers.
文摘The horizontal block stripe,as an image quality defect,was analyzed by means of output signals and bias voltage stress(BVS)test.The results showed that the defect was correlated with discharging efficiency.Further,two approaches were proposed,one was to improve TFT characteristic,the other was to add reset function.The combined experiments indicated that discharging promotion can improve the defect.Especially the latter is most optimal to eliminate the phenomenon.
基金Project(2017QHZ031)supported by Scientific Research Starting Project of Southwest Petroleum University,ChinaProject(18TD0013)supported by Science and Technology Innovation Team of Education Department of Sichuan for Dynamical System and Its Applications,ChinaProject(2017CXTD02)supported by Youth Science and Technology Innovation Team of Southwest Petroleum University for Nonlinear Systems,China。
文摘Faulted gas reservoirs are very common in reality,where some linear leaky faults divide the gas reservoir into several reservoir regions with distinct physical properties.This kind of gas reservoirs is also known as linear composite(LC)gas reservoirs.Although some analytical/semi-analytical models have been proposed to investigate pressure behaviors of producing wells in LC reservoirs based on the linear composite ideas,almost all of them focus on vertical wells and studies on multiple fractured horizontal wells are rare.After the pressure wave arrives at the leaky fault,pressure behaviors of multiple fractured horizontal wells will be affected by the leaky faults.Understanding the effect of leaky faults on pressure behaviors of multiple fractured horizontal wells is critical to the development design.Therefore,a semi-analytical model of finite-conductivity multiple fractured horizontal(FCMFH)wells in LC gas reservoirs is established based on Laplace-space superposition principle and fracture discrete method.The proposed model is validated against commercial numerical simulator.Type curves are obtained to study pressure characteristics and identify flow regimes.The effects of some parameters on type curves are discussed.The proposed model will have a profound effect on developing analytical/semi-analytical models for other complex well types in LC gas reservoirs.
基金Project(2016YFC0700100)supported by the National Key R&D Program of ChinaProject(JDJQ20160103)supported by the Promotion of the Connotation Development Quota Project of Colleges and Universities-Outstanding Youth of Architectural University,China。
文摘Effects of the flow pattern of intertubular liquid film on mass and heat transfer synergies in a falling-film dehumidification system with horizontal pipes are studied.A flow model of the dehumidifying solution between horizontal pipes is established using Fluent software,the rule of transitions of the flow pattern between pipes is studied,critical Reynolds numbers of flow pattern transitions are obtained,and the accuracy of the model is verified by experiments.The mass transfer synergy angle and heat transfer synergy angle are respectively used as evaluation criteria for the mass transfer synergy and heat transfer synergy,and distribution laws of the synergy angles for droplet,droplet columnar and curtain flow patterns are obtained.Simulation results show that the mass transfer synergy angles corresponding to droplet,droplet columnar and curtain flow patterns all rise to a plateau with time.The mean mass-transfer synergy angle is 98°for the droplet flow pattern,higher than 96.5°for the droplet columnar flow pattern and 95°for the curtain flow pattern.The results show that the mass transfer synergy of the droplet flow pattern is better than that of the droplet columnar flow pattern and that of the curtain flow pattern.
基金Supported by the National Natural Science Foundation of China(50778064)Hunan Natural Science Foundation(07jj6088)
文摘In this study a 10-storied residential building model was employed to clarify the ventilation characteristics of the atrium and the rooms,which were effected by the different forms of lateral openings.The experiment was conducted under the combined effect of wind force and thermal buoyancy,and the similarity requirements were satisfied.The results have shown that the different forms of lateral openings cause the different ventilation effect of the building,and also have some certain regularity.The conclusions provide a theoretical foundation for how to use the ventilation of atrium better in high-rise residential building.
基金Project(51108049)supported by the National Natural Science Foundation of ChinaProject(kfj090207)supported by Open Fund of Key Laboratory of Road Structure and Material of Ministry of Transport(Changsha University of Science and Technology),China
文摘Road horizontal alignment contains three elements: straight line,circular arc,and clothoid.In AutoCAD,clothoid can only be fitted by polyline or spline,and the graphics which are separated from the road data are independent of each other.Therefore,it is necessary to develop a new curve for road horizontal alignment.Firstly,the differential approximation and series integration methods for clothoid were discussed.Secondly,the geometric formulae for road line which contain the three elements were derived as a whole.Then,the advantages and feasibility of customizing a road line class,which was derived from the curve base class,were analyzed based on ObjectARX(AutoCAD Runtime eXtension) techniques.Finally,the data structure and operations for the road line class were stressed.The experimental results show that the road line can integrate the road elements,graphics and data to implement the graphics-oriented design,which can be widely used in road alignment design.
基金supported in part by the National Natural Science Foundation of China under Grant 51905271,Grant No.52275062and Grant No.52075262。
文摘Backlash nonlinearity inevitably exists in the actuator of tank horizontal stabilizer and has adverse effect on the system control performance,however,how to effectively eliminate its effect remains a pending issue.To solve this problem,a robust adaptive precision motion controller is presented in this paper to address uncertainties and unknown actuator backlash of tank horizontal actuator.The controller handles the modeling uncertainties including parameter uncertainties and unmodeled disturbances by integrating adaptive feedforward compensation and continuous nonlinear robust law.Based on the backstepping method,a smooth backlash inverse model is constructed by combining the adaptive idea.Meanwhile,the unknown backlash parameters of the system can be approximated through the parameter adaptation,and the impact of the actuator backlash nonlinearity is effectively compensated via the inverse operation,which can availably improve the tracking performance.Moreover,the adaptive law can update the disturbance ranges of tank horizontal stabilizer online in real time,which enhances the feasibility in practical engineering applications.Furthermore,the stability analysis based on Lyapunov function shows that with the existence of unmodeled disturbances and unknown actuator backlash,the designed controller guarantees excellent asymptotic output tracking performance.Extensive comparative results verify the effectiveness of the proposed control strategy.
基金Project(51278216) supported by the National Natural Science Foundation of China
文摘Based on reliability theory,a general method for the optimization design of piles subjected to horizontal loads is presented.This method takes into consideration various uncertainties caused by pile installation,variability of geotechnical materials from one location to another,and so on.It also deals with behavior and side constraints specified by standard specifications for piles.To more accurately solve the optimization design model,the first order reliability method is employed.The results from the numerical example indicate that the target reliability index has significant influence on design parameters.In addition,the optimization weight increases with the target reliability index.Especially when the target reliability index is relatively large,the target reliability index has significant influence on design weight of piles.
基金supported by the State Scholarship Fund(2011611091)supported by China Shipbuilding Industry Corporation
文摘This paper presents an approach to the challenging is- sue of passive source localization in shallow water using a mobile short horizontal linear array with length less than ten meters. The short array can be conveniently placed on autonomous underwa- ter vehicles and deployed for adaptive spatial sampling. However, the use of such small aperture passive sonar systems makes it difficult to acquire sufficient spatial gain for localizing long-range sources. To meet the requirement, a localization approach that employs matched-field based techniques that enable the short ho- rizontal linear array is used to passively localize acoustic sources in shallow water. Furthermore, the broadband processing and inter-position processing provide robustness against ocean en- vironmental mismatch and enhance the stability of the estimation process. The proposed approach＇s ability to localize acoustic sources in shallow water at different signal-to-noise ratios is examined through the synthetic test cases where the sources are located at the endfire and some other bearing of the mobile short horizontal linear array. The presented results demonstrate that the positional parameters of the estimated source build up over time as the array moves at a low speed along a straight line at a constant depth.
文摘Based on a dual-polarization high-frequency wave radar system, an adaptive system using horizontal antennas for the suppression of the Es layer interference （ELI） is deseribech The data received from the horizontal antennas were correlated with the data received from the Vertically Polarized Antennas （VPAs） to estimate and cancel the interference adaptively in the VPAs. Suppressing the interference after each coherent integration time interval, about 25 dB signal-to-interference ratio is expected with the experimentally derived data.
基金Project(20080431380)supported by the National Postdoctoral Science Foundation,China
文摘Based on theory of variable-mass system thermodynamics, the dynamic mathematic models of each component of the horizontal steam-launch system were established, and by the numerical simulation of the system launching process, the thermodynamics and kinetics characteristics of the system with three valves of different flow characteristics were got. The simulation results show that the values of the peak-to-average ratios of dimensionless acceleration with the equal percentage valve, the linear valve and the quick opening valve are 1.355, 1.614 and 1.722, respectively, and the final values of the dimensionless velocities are 0.843, 0.957 and 1.0, respectively. In conclusion, the value of the dimensionless velocity with the equal percentage valve doesn't reach the set value of 0.90 when the dimensionless displacement is 0.82, while the system with the linear valve can meet the launching requirement, as well as the fluctuation range of dimensionless acceleration is less than that of the quick opening valve. Therefore, the system with the linear valve has the best performance among the three kinds of valves.
基金Innovative Talent Research Fund of Harbin City(2006RFQXN011)
文摘The main structure and working principle of the single-shaft horizontal total mixed ration mixer was discussed. For studying the mixing principle, the analysis of force and motion of the material on the paddle were made, and paddle angle and rotational speed of the rotor were determined by the experiment, the main mixing ways were explained.
文摘In slab column-shear wall structures,both the whole structure′s seismic behavior and failure mode are greatly influenced by the distribution of horizontal seismic forces between slab-column and shear wall.In this paper,a pushover analysis of topical slab column-shear wall structure was carried out,the seismic shear force that the slab-column and shear wall should undertake was worked out,the influences of plastic internal force redistribution and structure stiffness characteristic value on horizontal seismic distribution were studied and the calculation formula was given.The analysis results showed that with the yield of the shear walls,the story shear force was undertaken by slab-columns correspondingly increased while with the decrease of characteristic value of stiffness of a structure,and the horizontal seismic force was undertaken by slab-columns correspondingly decreased.According to the code,the design of horizontal force distribution may be cause insecurity problems,so it is necessary to give the distribution law of horizontal seismic forces in slab-column shear wall structures as the supplement to the corresponding regulation of the Code.
