The effects of nanosecond laser shock peening without coating(LSPwC)and nanosecond stacked femtosecond laser shock peening compound strengthening(LSP-CS)on the surface integrity and fretting fatigue lifetime at 500℃o...The effects of nanosecond laser shock peening without coating(LSPwC)and nanosecond stacked femtosecond laser shock peening compound strengthening(LSP-CS)on the surface integrity and fretting fatigue lifetime at 500℃of GH 4169 dovetail component were investigated.The results show that LSP treatment does not significantly lead to changes in the grain size of GH 4169 alloy,but it introduces a large number of dislocations,resulting in the formation of a plastic deformation layer and residual compressive stress layer.The surface microhardness increased by 20.5%and 28.6%after being treated by LSPwC and LSP-CS,respectively.The surface residual compressive stresses were(-306.5±42.5)MPa and(-404.3±34.7)MPa,respectively;The depth of both the hardening layer and the residual compressive stress layer is 400μm,and along the cross-section with 0-100μm region after LSP-CS treatment has higher hardness and greater residual compressive stress.The fretting fatigue lifetime of the GH 4169 dovetail component at 500℃was increased by 346.8%and 494.9%,which is the result of the combined effects of the hardening layer and the residual stress layer.The LSP-CS treatment can effectively make up for the disadvantage of the LSPwC treatment,and further enhance the fretting fatigue lifetime of the GH 4169 dovetail component at high temperature.展开更多
The zirconium(Zr)alloy fuel cladding is one of the key structural components of a nuclear reactor and the first and most important line of defense for accommodating fission products.During the operation of nuclear rea...The zirconium(Zr)alloy fuel cladding is one of the key structural components of a nuclear reactor and the first and most important line of defense for accommodating fission products.During the operation of nuclear reactors,Zr alloy fuel cladding is subjected to extreme harsh environments,such as high temperature,high pressure and high flow rate for a long period of time.The wear and corrosion resistance of Zr alloys is important for the safe operation of nuclear reactors.Surface modification can effectively improve the corrosion and wear resistance of fuel cladding.Compared with coating technology,nitriding technology does not have problems for bonding between the coating and the substrate.Current research on surface nitriding of Zr alloys mainly focuses on plasma nitriding and ion implantation techniques.Research on laser nitriding of Zr alloy surfaces and their fretting wear characteristics is scarce.In this study,the surface of Zr alloy was treated with laser nitriding at different laser energies.The microstructure of Zr alloy treated with different laser energies and its fretting wear performance were studied.The results showed that after nitriding with different laser energies,the surface of the Zr alloy showed a typical molten state after melting,vaporizing and cooling under the thermal effect of the laser,and this state was more obvious with the increase of the laser energy.At the same time,doping of N atoms and formation of the ZrN phase led to different cooling rates in the molten zone that produced large tensile stresses after cooling.This led to cracks on the surface of Zr alloys after laser nitriding at different energies,and the crack density increased with increasing laser energy.This also led to an increase in the surface roughness of the Zr alloy with increasing laser energy after laser nitriding treatment.Due to the presence of water in the industrial nitrogen,nitrides were generated on the surface of the sample along with some oxides.When the laser energy was 100 mJ,there was no ZrN generation,and N existed mainly as a diffusion layer within the Zr alloy substrate.ZrN generated when the laser energy reached 200 mJ and above,which increased with the increase of laser energy.Due to the generation of ZrN phase and the presence of some oxides,the surface Vickers hardness of Zr alloys after laser nitriding treatment at different energies increased by 37.5%compared to Zr alloys.After laser nitriding treatment,the wear mechanism of Zr alloys changed.For the untreated Zr alloys,the wear mechanism was dominated by delamination and spalling wear,accompanied by oxidative and abrasive wear.The phenomenon of delamination and peeling decreased with the increase of laser energy.Wear mechanisms changed to predominantly abrasive wear with oxidative wear and delamination spalling.The wear volume of sample nitriding with laser energy 400 mJ was reduced by 46.5%compared with that of untreated Zr alloy.展开更多
荧光共振能量转移(Fluorescence Resonance Energy Transfer,FRET)技术被广泛应用于活细胞中生物大分子构象变化和分子间动态相互作用的实时研究.针对光谱串扰和供体受体间的浓度比等困扰FRET效率定量检测的两大难题,已经发展了多种定...荧光共振能量转移(Fluorescence Resonance Energy Transfer,FRET)技术被广泛应用于活细胞中生物大分子构象变化和分子间动态相互作用的实时研究.针对光谱串扰和供体受体间的浓度比等困扰FRET效率定量检测的两大难题,已经发展了多种定量检测FRET效率的方法.作者结合自己的研究结果介绍了多种FRET效率定量检测技术在细胞信号转导机制研究中的应用.展开更多
Singlet oxygen(1 O2) plays an important role in various applications, such as in the photodynamic therapy(PDT) of cancers,photodynamic inactivation of microorganisms, photo-degradation of toxic compounds, and photo-ox...Singlet oxygen(1 O2) plays an important role in various applications, such as in the photodynamic therapy(PDT) of cancers,photodynamic inactivation of microorganisms, photo-degradation of toxic compounds, and photo-oxidation in synthetic chemistry. Recently,water-soluble metal nanoclusters(NCs) have been utilized as photosensitizers for the generation of highly reactive 1 O2 because of their high water solubility, low toxicity, and surface functionalizability for targeted substances. In the case of metal NC-based photosensitizers, the photo-physical properties depend on the core size of the NCs and the core/ligand interfacial structures. A wide range of atomically precise gold NCs have been reported; however, reports on the synthesis of atomically precise silver NCs are limited due to the high reactivity and low photostability(i.e., easy oxidation) of Ag NCs. In addition, there have been few reports on what kinds of metal NCs can generate large amounts of 1 O2. In this study, we developed a new one-pot synthesis method of water-soluble Ag7(MBISA)6(MBISA= 2-mercapto-5-benzimidazolesulfonic acid sodium salt) NCs with highly efficient 1 O2 generation ability under the irradiation of white light emitting diodes(LEDs). The molecular formula and purity were determined by electrospray ionization mass spectrometry and gel electrophoresis. To the best of our knowledge, this is the first report on atomically precise thiolate silver clusters(Agn(SR)m) for efficient 1 O2 generation under visible light irradiation. The 1 O2 generation efficiency of Ag7(MBISA)6 NCs was higher than those of the following known water-soluble metal NCs: bovine serum albumin(BSA)-Au25 NCs,BSA-Ag8 NCs, BSA-Ag14 NCs,Ag25(dihydrolipoic acid)14 NCs,Ag35(glutathione)18 NCs,and Ag75(glutathione)40 NCs. The metal NCs examined in this study showed the following order of 1 O2 generation efficiency under white light irradiation: Ag7(MBISA)6 > BSA-Ag14 > Ag75(SG)40 > Ag35(SG)18 >BSA-Au25 >>BSA-Ags(not detected) and Ag2 s(DHLA)14(not detected). For further improving the 1 O2 generation of Ag7(MBISA)6 NCs, we developed a novel fluorescence resonance energy transfer(FRET) system by conjugating Ag7(MBISA)6 NCs with quinacrine(QC)(molar ratio of Ag NCs to QC is 1 : 0.5). We observed the FRET process,from QC to Ag7(MBISA)6 NCs,occurring in the conjugate. That is,the QC works as a donor chromophore,while the Ag NCs work as an acceptor chromophore in the FRET process. The FRET-mediated process caused a 2.3-fold increase in 1 O2 generation compared to that obtained with Ag7(MBISA)6 NCs alone. This study establishes a general and simple strategy for improving the PDT activity of metal NC-based photosensitizers.展开更多
目的探讨棕榈酰化修饰调节非受体酪氨酸激酶Fyn活性的分子机制。方法利用荧光共振能量转移(fluorescence resonance energy transfer,FRET)技术实时检测细胞中的Fyn活性,并结合棕榈酰化位点缺失和共转染蛋白质酪氨酸激酶(C-terminal Src...目的探讨棕榈酰化修饰调节非受体酪氨酸激酶Fyn活性的分子机制。方法利用荧光共振能量转移(fluorescence resonance energy transfer,FRET)技术实时检测细胞中的Fyn活性,并结合棕榈酰化位点缺失和共转染蛋白质酪氨酸激酶(C-terminal Src kinase,CSK)表达质粒研究其分子机制。结果实验发现,(C3,C6)任一位点的棕榈酰化缺失能引起Fyn的高活性表达,且C6位点影响更显著。已知CSK激活后发生膜转移,FRET检测证实其对细胞中的Fyn活性有下调作用,但不能有效调控(C3,C6)棕榈酰化位点缺失的Fyn(GSS)活性。结论本文结果初步支持了Fyn活性受细胞内的物理空间定位分布的一种调控机制假设,即棕榈酰化缺失的Fyn(GSS)受细胞膜上CSK抑制性的调节作用被减弱,从而促进了组成性的高活性表达。展开更多
In order to solve fretting instability problem of gear shaft shoulder due to torsional vibration in mechanical system, the mathematical model of fretting instability vibration of gear shaft shoulder was established by...In order to solve fretting instability problem of gear shaft shoulder due to torsional vibration in mechanical system, the mathematical model of fretting instability vibration of gear shaft shoulder was established by adopting the method of combining kinematics and tribology, and the numerical analysis was applied to the fretting instability mechanism of gear shaft shoulder by introducing the friction instability damping ratio. The numerical results show that the main factors causing the unstable and vibrating gear shaft shoulder are the large tightening torque and too large static friction coefficient. The reasonable values of the static friction coefficient, the amount of interference and tightening torque can effectively mitigate the fretting instability phenomenon of gear shaft shoulder. The experimental results verify that damping plays a significant role in eliminating the vibration of gear shaft control system.展开更多
基金Project(2022YFB3401900)supported by the the National Key R&D of ChinaProject(2025YFHZ0163)supported by the the Science and Technology Projects in Sichuan Province,ChinaProject(2682024GF004)supported by Fundamental Research Funds for the Centeral University,China。
文摘The effects of nanosecond laser shock peening without coating(LSPwC)and nanosecond stacked femtosecond laser shock peening compound strengthening(LSP-CS)on the surface integrity and fretting fatigue lifetime at 500℃of GH 4169 dovetail component were investigated.The results show that LSP treatment does not significantly lead to changes in the grain size of GH 4169 alloy,but it introduces a large number of dislocations,resulting in the formation of a plastic deformation layer and residual compressive stress layer.The surface microhardness increased by 20.5%and 28.6%after being treated by LSPwC and LSP-CS,respectively.The surface residual compressive stresses were(-306.5±42.5)MPa and(-404.3±34.7)MPa,respectively;The depth of both the hardening layer and the residual compressive stress layer is 400μm,and along the cross-section with 0-100μm region after LSP-CS treatment has higher hardness and greater residual compressive stress.The fretting fatigue lifetime of the GH 4169 dovetail component at 500℃was increased by 346.8%and 494.9%,which is the result of the combined effects of the hardening layer and the residual stress layer.The LSP-CS treatment can effectively make up for the disadvantage of the LSPwC treatment,and further enhance the fretting fatigue lifetime of the GH 4169 dovetail component at high temperature.
文摘The zirconium(Zr)alloy fuel cladding is one of the key structural components of a nuclear reactor and the first and most important line of defense for accommodating fission products.During the operation of nuclear reactors,Zr alloy fuel cladding is subjected to extreme harsh environments,such as high temperature,high pressure and high flow rate for a long period of time.The wear and corrosion resistance of Zr alloys is important for the safe operation of nuclear reactors.Surface modification can effectively improve the corrosion and wear resistance of fuel cladding.Compared with coating technology,nitriding technology does not have problems for bonding between the coating and the substrate.Current research on surface nitriding of Zr alloys mainly focuses on plasma nitriding and ion implantation techniques.Research on laser nitriding of Zr alloy surfaces and their fretting wear characteristics is scarce.In this study,the surface of Zr alloy was treated with laser nitriding at different laser energies.The microstructure of Zr alloy treated with different laser energies and its fretting wear performance were studied.The results showed that after nitriding with different laser energies,the surface of the Zr alloy showed a typical molten state after melting,vaporizing and cooling under the thermal effect of the laser,and this state was more obvious with the increase of the laser energy.At the same time,doping of N atoms and formation of the ZrN phase led to different cooling rates in the molten zone that produced large tensile stresses after cooling.This led to cracks on the surface of Zr alloys after laser nitriding at different energies,and the crack density increased with increasing laser energy.This also led to an increase in the surface roughness of the Zr alloy with increasing laser energy after laser nitriding treatment.Due to the presence of water in the industrial nitrogen,nitrides were generated on the surface of the sample along with some oxides.When the laser energy was 100 mJ,there was no ZrN generation,and N existed mainly as a diffusion layer within the Zr alloy substrate.ZrN generated when the laser energy reached 200 mJ and above,which increased with the increase of laser energy.Due to the generation of ZrN phase and the presence of some oxides,the surface Vickers hardness of Zr alloys after laser nitriding treatment at different energies increased by 37.5%compared to Zr alloys.After laser nitriding treatment,the wear mechanism of Zr alloys changed.For the untreated Zr alloys,the wear mechanism was dominated by delamination and spalling wear,accompanied by oxidative and abrasive wear.The phenomenon of delamination and peeling decreased with the increase of laser energy.Wear mechanisms changed to predominantly abrasive wear with oxidative wear and delamination spalling.The wear volume of sample nitriding with laser energy 400 mJ was reduced by 46.5%compared with that of untreated Zr alloy.
文摘荧光共振能量转移(Fluorescence Resonance Energy Transfer,FRET)技术被广泛应用于活细胞中生物大分子构象变化和分子间动态相互作用的实时研究.针对光谱串扰和供体受体间的浓度比等困扰FRET效率定量检测的两大难题,已经发展了多种定量检测FRET效率的方法.作者结合自己的研究结果介绍了多种FRET效率定量检测技术在细胞信号转导机制研究中的应用.
基金The project was supported by the JSPS KAKENH1, Japan (15H03520, 15H03526, and 26107719), and the MEXT-Supported Program for the Strategic Research Foundation at Private Universities, Japan.
文摘Singlet oxygen(1 O2) plays an important role in various applications, such as in the photodynamic therapy(PDT) of cancers,photodynamic inactivation of microorganisms, photo-degradation of toxic compounds, and photo-oxidation in synthetic chemistry. Recently,water-soluble metal nanoclusters(NCs) have been utilized as photosensitizers for the generation of highly reactive 1 O2 because of their high water solubility, low toxicity, and surface functionalizability for targeted substances. In the case of metal NC-based photosensitizers, the photo-physical properties depend on the core size of the NCs and the core/ligand interfacial structures. A wide range of atomically precise gold NCs have been reported; however, reports on the synthesis of atomically precise silver NCs are limited due to the high reactivity and low photostability(i.e., easy oxidation) of Ag NCs. In addition, there have been few reports on what kinds of metal NCs can generate large amounts of 1 O2. In this study, we developed a new one-pot synthesis method of water-soluble Ag7(MBISA)6(MBISA= 2-mercapto-5-benzimidazolesulfonic acid sodium salt) NCs with highly efficient 1 O2 generation ability under the irradiation of white light emitting diodes(LEDs). The molecular formula and purity were determined by electrospray ionization mass spectrometry and gel electrophoresis. To the best of our knowledge, this is the first report on atomically precise thiolate silver clusters(Agn(SR)m) for efficient 1 O2 generation under visible light irradiation. The 1 O2 generation efficiency of Ag7(MBISA)6 NCs was higher than those of the following known water-soluble metal NCs: bovine serum albumin(BSA)-Au25 NCs,BSA-Ag8 NCs, BSA-Ag14 NCs,Ag25(dihydrolipoic acid)14 NCs,Ag35(glutathione)18 NCs,and Ag75(glutathione)40 NCs. The metal NCs examined in this study showed the following order of 1 O2 generation efficiency under white light irradiation: Ag7(MBISA)6 > BSA-Ag14 > Ag75(SG)40 > Ag35(SG)18 >BSA-Au25 >>BSA-Ags(not detected) and Ag2 s(DHLA)14(not detected). For further improving the 1 O2 generation of Ag7(MBISA)6 NCs, we developed a novel fluorescence resonance energy transfer(FRET) system by conjugating Ag7(MBISA)6 NCs with quinacrine(QC)(molar ratio of Ag NCs to QC is 1 : 0.5). We observed the FRET process,from QC to Ag7(MBISA)6 NCs,occurring in the conjugate. That is,the QC works as a donor chromophore,while the Ag NCs work as an acceptor chromophore in the FRET process. The FRET-mediated process caused a 2.3-fold increase in 1 O2 generation compared to that obtained with Ag7(MBISA)6 NCs alone. This study establishes a general and simple strategy for improving the PDT activity of metal NC-based photosensitizers.
基金Project(2008AA11A116)supported by the National High Technology Research and Development Program of ChinaProject(9140A2011QT4801)supported by advanced research of the Weapon Equipment Key Fund Program,ChinaProject(61075002)supported by the Independent Subject of State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body of Hunan University,China
文摘In order to solve fretting instability problem of gear shaft shoulder due to torsional vibration in mechanical system, the mathematical model of fretting instability vibration of gear shaft shoulder was established by adopting the method of combining kinematics and tribology, and the numerical analysis was applied to the fretting instability mechanism of gear shaft shoulder by introducing the friction instability damping ratio. The numerical results show that the main factors causing the unstable and vibrating gear shaft shoulder are the large tightening torque and too large static friction coefficient. The reasonable values of the static friction coefficient, the amount of interference and tightening torque can effectively mitigate the fretting instability phenomenon of gear shaft shoulder. The experimental results verify that damping plays a significant role in eliminating the vibration of gear shaft control system.
