为了解火灾环境下含炸药结构的热响应行为，针对其涉及的主要传热学问题，建立了池火灾火焰温升数值模型，碳/酚醛烧蚀层高温热解吸热数值模型，空气夹层复合传热数值模型，以及炸药受热分解放热数值模型。用所建数值模型，计算并获得...为了解火灾环境下含炸药结构的热响应行为，针对其涉及的主要传热学问题，建立了池火灾火焰温升数值模型，碳/酚醛烧蚀层高温热解吸热数值模型，空气夹层复合传热数值模型，以及炸药受热分解放热数值模型。用所建数值模型，计算并获得了含炸药结构在不同温升条件下（恒定值1073 K、1273 K 及本研究所提的火焰实测温升曲线）、不同火焰辐射率（0．1～0．9）和不同空气夹层间壳体表面辐射率（0．1～0．9）下的温度响应和热点火延滞时间。结果表明：火烧30 min 情况下，火焰温度为1273 K 时，内部炸药在28．92 min 已经发生热点火现象。火焰温度为1073 K 和实测温升曲线时，内部炸药最高温度分别为448 K 和535 K。火焰辐射率从0．9降低到0．1时，内部炸药最高温度由535．4 K 降低到344．6 K，热点火延滞时间由1917 s 增加到3520 s。空气夹层间壳体表面辐射率由0．9降低到0．1时，内部炸药最高温度由535．4 K 降低到329．0 K，热点火延滞时间由1917 s 增加到3739 s。展开更多
In the feeding process of aluminum electrolytic, feeding quantity of alumina affects eventually dissolved quantity at the end of a feeding cycle. Based on the OpenFOAM platform, dissolution model coupled with heat and...In the feeding process of aluminum electrolytic, feeding quantity of alumina affects eventually dissolved quantity at the end of a feeding cycle. Based on the OpenFOAM platform, dissolution model coupled with heat and mass transfer was established. Applying the Rosin-Rammler function, alumina particle size distribution under different feeding quantities was obtained. The temperature response of electrolyte after feeding was included and calculated, and the dissolution processes of alumina with different feeding quantities (0.6, 0.8, 1.0, 1.2, 1.4, 1.6 kg) after feeding were simulated in 300 kA aluminum reduction cell. The results show that with the increase of feeding quantity, accumulated mass fraction of dissolved alumina decreases, and the time required for the rapid dissolution stage extends. When the feeding quantity is 0.6 kg and 1.2 kg, it takes the shortest time for the electrolyte temperature dropping before rebounding back. With the increase of feeding quantity, the dissolution rate in the rapid dissolution stage increases at first and then decreases gradually. The most suitable feeding quantity is 1.2 kg. The fitting equation of alumina dissolution curve under different feeding quantities is obtained, which can be used to evaluate the alumina dissolution and guide the feeding quantity and feeding cycle.展开更多
As a new type of structure which has never been built, submerged floating tunnel was studied mainly by numerical simulations. To further study the seismic response of a submerged floating tunnel, the first model exper...As a new type of structure which has never been built, submerged floating tunnel was studied mainly by numerical simulations. To further study the seismic response of a submerged floating tunnel, the first model experiment of submerged floating tunnel （SFT） under the earthquake was carried out on the unique underwater shaking table in China. The experimental results show that vertical excitation induces larger response than horizontal and different inclination degrees of the tether also cause different seismic responses. Subsequently, based on the fluid-structure interaction theory, the corresponding numerical model is established. And comparing the numerical results with the experimental results, those of shaking table test. Numerical model adopted is effective for it is shown that the numerical results are basically identical with dynamic response of SFT.展开更多
To make the dynamic assembly reliability analysis more effective for complex machinery of multi-object multi-discipline(MOMD),distributed collaborative extremum response surface method(DCERSM)was proposed based on ext...To make the dynamic assembly reliability analysis more effective for complex machinery of multi-object multi-discipline(MOMD),distributed collaborative extremum response surface method(DCERSM)was proposed based on extremum response surface method(ERSM).Firstly,the basic theories of the ERSM and DCERSM were investigated,and the strengths of DCERSM were proved theoretically.Secondly,the mathematical model of the DCERSM was established based upon extremum response surface function(ERSF).Finally,this model was applied to the reliability analysis of blade-tip radial running clearance(BTRRC)of an aeroengine high pressure turbine(HPT)to verify its advantages.The results show that the DCERSM can not only reshape the possibility of the reliability analysis for the complex turbo machinery,but also greatly improve the computational speed,save the computational time and improve the computational efficiency while keeping the accuracy.Thus,the DCERSM is verified to be feasible and effective in the dynamic assembly reliability(DAR)analysis of complex machinery.Moreover,this method offers an useful insight for designing and optimizing the dynamic reliability of complex machinery.展开更多
Deformation prediction and the analysis of underground goaf are important to the safe and efficient recovery of residual ore when shifting from open-pit mining to underground mining.To address the comprehensive proble...Deformation prediction and the analysis of underground goaf are important to the safe and efficient recovery of residual ore when shifting from open-pit mining to underground mining.To address the comprehensive problem of stability in the double mined-out area of the Tong-Lv-Shan(TLS)mine,which employed the dry stacked gangue technology,this paper applies the function fitting theory and a regression analysis method to screen the sensitive interval of four influencing factors based on single-factor experiments and the numerical simulation software FLAC3D.The influencing factors of the TLS mine consist of the column thickness(d),gob area span(D),boundary pillar thickness(h)and height of tailing gangue(H).The fitting degree between the four factors and the displacement of the gob roof(W)is reasonable because the correlation coefficient(R2)is greater than0.9701.After establishing29groups that satisfy the principles of Box-Behnken design(BBD),the dry gangue tailings process was re-simulated for the selected sensitive interval.Using a combination of an analysis of variance(ANOVA),regression equations and a significance analysis,the prediction results of the response surface methodology(RSM)show that the significant degree for the stability of the mined-out area for the factors satisfies the relationship of h>D>d>H.The importance of the four factors cannot be disregarded in a comparison of the prediction results of the engineering test stope in the TLS mine.By comparing the data of monitoring points and function prediction,the proposed method has shown promising results,and the prediction accuracy of RSM model is acceptable.The relative errors of the two test stopes are1.67%and3.85%,respectively,which yield satisfactory reliability and reference values for the mines.展开更多
The microscopic response characteristics of nuclear magnetic resonance(NMR) are widely used for characterizing complex pore structures of rocks. Due to the prohibitive NMR experiment cost, numerical simulation was emp...The microscopic response characteristics of nuclear magnetic resonance(NMR) are widely used for characterizing complex pore structures of rocks. Due to the prohibitive NMR experiment cost, numerical simulation was employed as an alternative approach to verify some theoretical aspects of NMR responses. Firstly, the basic principles of pore-scale NMR simulation based on random-walk method(RWM) were introduced. The RWM-simulated results were benchmarked with the analytical results for an ideal spherical pore model. Then, the effects of two numerical parameters, namely diffusion radius and walk numbers, were studied on the simulation accuracy. The simulation method is then applied to various pore models with different pore sizes and pore shapes filled with different fluids to study the microscopic NMR response characteristics. The numerical experiments are useful for understanding and interpreting NMR measurements and the simulation code provides a numerical tool to perform pixel-based digital rock analysis.展开更多
Most modern tall buildings using lighter construction materials are more flexible, which can lead to excessive wind-induced vibrations resulting in occupant discomfort and structural unsafety. It is necessary to predi...Most modern tall buildings using lighter construction materials are more flexible, which can lead to excessive wind-induced vibrations resulting in occupant discomfort and structural unsafety. It is necessary to predict and mitigate such wind-induced vibration at the preliminary design stage. Fluctuating across and along-wind loads acting on a tall building that could not be formulated theoretically were simulated numerically in the time domain using known across and along-wind load spectra. These simulated wind loads were used to estimate the across and along-wind responses of a tall building, which are less narrow-banded processes, based on the state space variable approach. The simulated across-wind response of root-mean-square value(0.0047) and that of KAREEM's(0.0040) and the simulated along-wind response of root-mean-square value(0.021) and that of SOLARI's(0.027) were compared. It is found that these are good approximations of closed form responses. Therefore, these numerically simulated across and along-wind loads can be used for across and along-wind responses estimation for the wind-resistant design of a tall building at the preliminary design stage.展开更多
Combining the optimization and FEM technology,crashworthiness of aluminum extrusions was studied for an automobile safety plan.The effects of longitudinal stiffeners on the crushing of stiffened square columns were st...Combining the optimization and FEM technology,crashworthiness of aluminum extrusions was studied for an automobile safety plan.The effects of longitudinal stiffeners on the crushing of stiffened square columns were studied considering the damage evolution.The numerical analysis was carried out by ABAQUS software.Subsequently,the collapse behavior of aluminum extrusion damage was validated by comparing against solution published in literature.Finally,in order to find more efficient and lighter crush absorber and achieving minimum peak crushing force,response surface methodology(RSM) has been applied for optimizing the aluminum extrusion tube.展开更多
Due to the extreme complexity of mechanical response of soft surrounding rock(SR) around a tunnel under high geostatic stress conditions, the integration of physical and numerical modeling techniques was adopted. Base...Due to the extreme complexity of mechanical response of soft surrounding rock(SR) around a tunnel under high geostatic stress conditions, the integration of physical and numerical modeling techniques was adopted. Based on the similarity theory, new composite-similar material was developed, which showed good agreement with the similarity relation and successfully simulated physico-mechanical properties(PMP) of deep buried soft rock. And the 800 mm×800 mm×200 mm physical model(PM) was conducted, in which the endoscopic camera technique was adopted to track the entire process of failure of the model all the time. The experimental results indicate that the deformation of SR around a underground cavern possessed the characteristics of development by stages and in delay, and the initial damage of SR could induce rapid failure in the later stage, and the whole process could be divided into three stages, including the localized extension of crack(the horizontal load(HL) was in the range of 130 k N to 170 k N, the vertical load(VL) was in the range of 119 k N to 153.8 k N), rapid crack coalescence(the HL was in the range of 170 k N to 210 k N, the VL was in the range of 153.8 k N to 182.5 k N) and residual strength(the HL was greater than 210 k N, the VL was greater than 182.5 k N). Under the high stress conditions, the phenomenon of deformation localization in the SR became serious and different space positions show different deformation characteristics. In order to further explore the deformation localization and progressive failure phenomenon of soft SR around the deeply buried tunnel, applying the analysis software of FLAC3 D three-dimensional explicit finite-difference method, based on the composite strain-softening model of Mohr-Coulomb shear failure and tensile failure, the calculation method of large deformation was adopted. Then, the comparative analysis between the PM experiment and numerical simulation of the three centered arch tunnels was implemented and the relationship of deformation localization and progressive failure of SR around a tunnel under high stress conditions was discussed.展开更多
文摘为了解火灾环境下含炸药结构的热响应行为，针对其涉及的主要传热学问题，建立了池火灾火焰温升数值模型，碳/酚醛烧蚀层高温热解吸热数值模型，空气夹层复合传热数值模型，以及炸药受热分解放热数值模型。用所建数值模型，计算并获得了含炸药结构在不同温升条件下（恒定值1073 K、1273 K 及本研究所提的火焰实测温升曲线）、不同火焰辐射率（0．1～0．9）和不同空气夹层间壳体表面辐射率（0．1～0．9）下的温度响应和热点火延滞时间。结果表明：火烧30 min 情况下，火焰温度为1273 K 时，内部炸药在28．92 min 已经发生热点火现象。火焰温度为1073 K 和实测温升曲线时，内部炸药最高温度分别为448 K 和535 K。火焰辐射率从0．9降低到0．1时，内部炸药最高温度由535．4 K 降低到344．6 K，热点火延滞时间由1917 s 增加到3520 s。空气夹层间壳体表面辐射率由0．9降低到0．1时，内部炸药最高温度由535．4 K 降低到329．0 K，热点火延滞时间由1917 s 增加到3739 s。
基金Project(2010AA065201) supported by the High-Tech Research and Development Program of ChinaProject(2018zzts157) supported by the Fundamental Research Funds for the Central Universities,China
文摘In the feeding process of aluminum electrolytic, feeding quantity of alumina affects eventually dissolved quantity at the end of a feeding cycle. Based on the OpenFOAM platform, dissolution model coupled with heat and mass transfer was established. Applying the Rosin-Rammler function, alumina particle size distribution under different feeding quantities was obtained. The temperature response of electrolyte after feeding was included and calculated, and the dissolution processes of alumina with different feeding quantities (0.6, 0.8, 1.0, 1.2, 1.4, 1.6 kg) after feeding were simulated in 300 kA aluminum reduction cell. The results show that with the increase of feeding quantity, accumulated mass fraction of dissolved alumina decreases, and the time required for the rapid dissolution stage extends. When the feeding quantity is 0.6 kg and 1.2 kg, it takes the shortest time for the electrolyte temperature dropping before rebounding back. With the increase of feeding quantity, the dissolution rate in the rapid dissolution stage increases at first and then decreases gradually. The most suitable feeding quantity is 1.2 kg. The fitting equation of alumina dissolution curve under different feeding quantities is obtained, which can be used to evaluate the alumina dissolution and guide the feeding quantity and feeding cycle.
基金Projects(51108224,51179026) supported by the National Natural Science Foundation of China
文摘As a new type of structure which has never been built, submerged floating tunnel was studied mainly by numerical simulations. To further study the seismic response of a submerged floating tunnel, the first model experiment of submerged floating tunnel （SFT） under the earthquake was carried out on the unique underwater shaking table in China. The experimental results show that vertical excitation induces larger response than horizontal and different inclination degrees of the tether also cause different seismic responses. Subsequently, based on the fluid-structure interaction theory, the corresponding numerical model is established. And comparing the numerical results with the experimental results, those of shaking table test. Numerical model adopted is effective for it is shown that the numerical results are basically identical with dynamic response of SFT.
基金Project(51175017)supported by the National Natural Science Foundation of ChinaProject(YWF-12-RBYJ-008)supported by the Innovation Foundation of Beihang University for PhD Graduates,ChinaProject(20111102110011)supported by the Research Fund for the Doctoral Program of Higher Education of China
文摘To make the dynamic assembly reliability analysis more effective for complex machinery of multi-object multi-discipline(MOMD),distributed collaborative extremum response surface method(DCERSM)was proposed based on extremum response surface method(ERSM).Firstly,the basic theories of the ERSM and DCERSM were investigated,and the strengths of DCERSM were proved theoretically.Secondly,the mathematical model of the DCERSM was established based upon extremum response surface function(ERSF).Finally,this model was applied to the reliability analysis of blade-tip radial running clearance(BTRRC)of an aeroengine high pressure turbine(HPT)to verify its advantages.The results show that the DCERSM can not only reshape the possibility of the reliability analysis for the complex turbo machinery,but also greatly improve the computational speed,save the computational time and improve the computational efficiency while keeping the accuracy.Thus,the DCERSM is verified to be feasible and effective in the dynamic assembly reliability(DAR)analysis of complex machinery.Moreover,this method offers an useful insight for designing and optimizing the dynamic reliability of complex machinery.
基金Project(2017YFC0602902) supported by the National Science and Technology Pillar Program during the 13th Five-Year Plan Period,ChinaProject(2015CX005) supported by the Innovation Driven Plan of Central South University,ChinaProject(2016zzts445) supported by the Fundamental Research Funds for the Central Universities,China
文摘Deformation prediction and the analysis of underground goaf are important to the safe and efficient recovery of residual ore when shifting from open-pit mining to underground mining.To address the comprehensive problem of stability in the double mined-out area of the Tong-Lv-Shan(TLS)mine,which employed the dry stacked gangue technology,this paper applies the function fitting theory and a regression analysis method to screen the sensitive interval of four influencing factors based on single-factor experiments and the numerical simulation software FLAC3D.The influencing factors of the TLS mine consist of the column thickness(d),gob area span(D),boundary pillar thickness(h)and height of tailing gangue(H).The fitting degree between the four factors and the displacement of the gob roof(W)is reasonable because the correlation coefficient(R2)is greater than0.9701.After establishing29groups that satisfy the principles of Box-Behnken design(BBD),the dry gangue tailings process was re-simulated for the selected sensitive interval.Using a combination of an analysis of variance(ANOVA),regression equations and a significance analysis,the prediction results of the response surface methodology(RSM)show that the significant degree for the stability of the mined-out area for the factors satisfies the relationship of h>D>d>H.The importance of the four factors cannot be disregarded in a comparison of the prediction results of the engineering test stope in the TLS mine.By comparing the data of monitoring points and function prediction,the proposed method has shown promising results,and the prediction accuracy of RSM model is acceptable.The relative errors of the two test stopes are1.67%and3.85%,respectively,which yield satisfactory reliability and reference values for the mines.
基金Project(265201248) supported by the Fundamental Research Funds for the Central Universities,ChinaProject(41172130) supported by the National Natural Science Foundation of China+2 种基金Project(2011ZX05014-001) supported by the Major State S&T Special Fund,ChinaProject(201205002) supported by the China Scholarship CouncilProject(2011D-5006-0305) supported by the China National Petroleum Co.Innovation Foundation,China
文摘The microscopic response characteristics of nuclear magnetic resonance(NMR) are widely used for characterizing complex pore structures of rocks. Due to the prohibitive NMR experiment cost, numerical simulation was employed as an alternative approach to verify some theoretical aspects of NMR responses. Firstly, the basic principles of pore-scale NMR simulation based on random-walk method(RWM) were introduced. The RWM-simulated results were benchmarked with the analytical results for an ideal spherical pore model. Then, the effects of two numerical parameters, namely diffusion radius and walk numbers, were studied on the simulation accuracy. The simulation method is then applied to various pore models with different pore sizes and pore shapes filled with different fluids to study the microscopic NMR response characteristics. The numerical experiments are useful for understanding and interpreting NMR measurements and the simulation code provides a numerical tool to perform pixel-based digital rock analysis.
基金Project(2011-0028567)supported by the National Research Foundation of Korea
文摘Most modern tall buildings using lighter construction materials are more flexible, which can lead to excessive wind-induced vibrations resulting in occupant discomfort and structural unsafety. It is necessary to predict and mitigate such wind-induced vibration at the preliminary design stage. Fluctuating across and along-wind loads acting on a tall building that could not be formulated theoretically were simulated numerically in the time domain using known across and along-wind load spectra. These simulated wind loads were used to estimate the across and along-wind responses of a tall building, which are less narrow-banded processes, based on the state space variable approach. The simulated across-wind response of root-mean-square value(0.0047) and that of KAREEM's(0.0040) and the simulated along-wind response of root-mean-square value(0.021) and that of SOLARI's(0.027) were compared. It is found that these are good approximations of closed form responses. Therefore, these numerically simulated across and along-wind loads can be used for across and along-wind responses estimation for the wind-resistant design of a tall building at the preliminary design stage.
文摘Combining the optimization and FEM technology,crashworthiness of aluminum extrusions was studied for an automobile safety plan.The effects of longitudinal stiffeners on the crushing of stiffened square columns were studied considering the damage evolution.The numerical analysis was carried out by ABAQUS software.Subsequently,the collapse behavior of aluminum extrusion damage was validated by comparing against solution published in literature.Finally,in order to find more efficient and lighter crush absorber and achieving minimum peak crushing force,response surface methodology(RSM) has been applied for optimizing the aluminum extrusion tube.
基金Projects(51374257,50804060)supported by the National Natural Science Foundation of ChinaProject(NCET-09-0844)supported by the New Century Excellent Talent Foundation from MOE of China
文摘Due to the extreme complexity of mechanical response of soft surrounding rock(SR) around a tunnel under high geostatic stress conditions, the integration of physical and numerical modeling techniques was adopted. Based on the similarity theory, new composite-similar material was developed, which showed good agreement with the similarity relation and successfully simulated physico-mechanical properties(PMP) of deep buried soft rock. And the 800 mm×800 mm×200 mm physical model(PM) was conducted, in which the endoscopic camera technique was adopted to track the entire process of failure of the model all the time. The experimental results indicate that the deformation of SR around a underground cavern possessed the characteristics of development by stages and in delay, and the initial damage of SR could induce rapid failure in the later stage, and the whole process could be divided into three stages, including the localized extension of crack(the horizontal load(HL) was in the range of 130 k N to 170 k N, the vertical load(VL) was in the range of 119 k N to 153.8 k N), rapid crack coalescence(the HL was in the range of 170 k N to 210 k N, the VL was in the range of 153.8 k N to 182.5 k N) and residual strength(the HL was greater than 210 k N, the VL was greater than 182.5 k N). Under the high stress conditions, the phenomenon of deformation localization in the SR became serious and different space positions show different deformation characteristics. In order to further explore the deformation localization and progressive failure phenomenon of soft SR around the deeply buried tunnel, applying the analysis software of FLAC3 D three-dimensional explicit finite-difference method, based on the composite strain-softening model of Mohr-Coulomb shear failure and tensile failure, the calculation method of large deformation was adopted. Then, the comparative analysis between the PM experiment and numerical simulation of the three centered arch tunnels was implemented and the relationship of deformation localization and progressive failure of SR around a tunnel under high stress conditions was discussed.
