Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrati...Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrations of HPAM as well as mixtures of polyacrylamide/xanthan gum were prepared to investigate the possibility of improving shear stability of HPAM.Drag reduction（DR）measurements were performed in a closed flow loop.For HPAM solutions,the extent of DR increased from 30%to67%with increasing HPAM concentration from 100 to1000 wppm.All the HPAM solutions suffered from mechanical degradation and loss of DR efficiency over the shearing period.Results indicated that the resistance to shear degradation increased with increasing polymer concentration.DR efficiency of 600 wppm xanthan gum（XG）was 38%,indicating that XG was not as good a drag reducer as HPAM.But with only 6%DR decline,XG solution exhibited a better shear stability compared to HPAM solutions.Mixed HPAM/XG solutions initially exhibited greater DR（40%and 55%）compared to XG,but due to shear degradation,DR%dropped for HPAM/XG solutions.Compared to 200 wppm HPAM solution,addition of XG did not improve the drag reduction efficiency of HPAM/XG mixed solutions though XG slightly improved the resistance against mechanical degradation in HPAM/XG mixed polymer solutions.展开更多
In this work, non-thermal plasma has been applied to treat polyacrylamide（PAM） wastewater.We have investigated the influence of the rule of PAM wastewater initial pH, solution concentration and discharge time, disch...In this work, non-thermal plasma has been applied to treat polyacrylamide（PAM） wastewater.We have investigated the influence of the rule of PAM wastewater initial pH, solution concentration and discharge time, discharge voltage on chemical oxygen demand（COD）degradation rate. At the same time, the effect of pH and discharge time on the viscosity removal rate of PAM solution was also studied. Then, the effect of pH on the viscosity removal rate of1.0 gl-1 PAM solution was studied separately. Through orthogonal test, the factors affecting the COD degradation rate of PAM wastewater were determined as follows: discharge time > discharge voltage > solution concentration > wastewater initial pH. The COD highest removal rate of PAM wastewater reached 85.74%, when the optimal conditions are as follows:discharge voltage 40 k V, discharge time 5 h, solution concentration 1.0 gl-1, pH 1.5. This research provides some basic data and new theoretical basis for PAM wastewater purification.展开更多
In this paper, cationic polyacrylamide microspheres （CPAM） were synthesized using acrylamide （AM） and methacryloyloxyethyl trimethyl ammonium chloride （TMAEMC） as monomers, ammonium sulfate as dispersant, poly（...In this paper, cationic polyacrylamide microspheres （CPAM） were synthesized using acrylamide （AM） and methacryloyloxyethyl trimethyl ammonium chloride （TMAEMC） as monomers, ammonium sulfate as dispersant, poly（acryloyloxyethyl trimethyl ammonium chloride） （PAETAC） as dispersion stabilizer, and ammonium persulfate as initiator. The synthetic method was dispersion polymerization. The effects of monomer ratio （AM/TMAEMC）, dispersant concentration, and dispersion stabilizer dosage on dispersion polymerization were systematically studied to determine the optimal preparation conditions. The structure and viscosity of the synthesized polymer were characterized by FTIR and capillary viscometry, respectively, and the particle sizes and distribution of the polymer microspheres were characterized by microscopy and dynamic light scattering, respectively. Finally, flow tests were conducted to measure the permeability reduction performance of the microspheres at various concentrations in sand packs with different permeability. Results show that CPAM emulsion of a solids content of 1 wt% has excellent performance in low-to-medium permeability formations （〈 1,000 mD）, and the efficiency may reach above 90%.展开更多
A temperature-resistant, salt-tolerant polyacrylamide, hydrophobically associating polymer （HAP）, was synthesized in the State Key Laboratory of Heavy Oil Processing. The rheological behavior of HAP solution was inv...A temperature-resistant, salt-tolerant polyacrylamide, hydrophobically associating polymer （HAP）, was synthesized in the State Key Laboratory of Heavy Oil Processing. The rheological behavior of HAP solution was investigated by means of flow experiments in porous media and by using a HAAKE RS600 rheometer. The results of Nuclepore membrane filtration showed that filtration time increased sharply when the critical association concentration was reached. Shear rate had a greater impact on viscosity and shear stress with increasing HAP concentration. The HAP solution with a concentration of 100 mg/L （salinity 32,868 mg/L） exhibited negative thixotropy. However, at the same salinity the HAP solution showed thixotropy and its viscosity became greater when the polymer concentration increased to 1,500 mg/L. The flow experiments in cemented core samples indicated that the resistance factor and residual resistance factor of the HAP solution were 31.8 and 12 when polymer concentration and salinity were 1,500 mg/L, 32,868 mg/L at 85℃ respectively, which is favorable for flooding application. Such factors of partially hydrolyzed polyaerylamide 3530S were merely 3.14 and 1.71, so it could not be applied to polymer flooding in the oilfield with high temperature and high salinity.展开更多
Interaction of polymer-containing injected fluids with shale is a widely studied phenomenon, but much is still unknown about the interaction of charged polyacrylamides such as anionic and cationic polyacrylamides with...Interaction of polymer-containing injected fluids with shale is a widely studied phenomenon, but much is still unknown about the interaction of charged polyacrylamides such as anionic and cationic polyacrylamides with shale. The nature of interaction of charged polyacrylamides with shale is not well understood, especially from the perspective of assessing the potential for polyacrylamides to cause formation damage. Zeta potential and rheological measurements were made for Chattanooga and Pride Mountain shales suspended in polyacrylamide solutions with and without inorganic salts and tetramethyl ammonium chloride（TMAC）. The change in zeta potential and viscosity with time was recorded. The magnitude of decrease in the absolute value of zeta potential with time is indicative of adsorption of polymer on the surface of shale and serves as a measure of the extent of polymer interaction with shale. The salts that were used in this study are potassium chloride（KCl）, sodium chloride（Na Cl）. This study quantified the interaction of anionic and cationic polyacrylamide with different North American shales.From the experimental results, it was determined that the polyacrylamides can interact strongly with shale, particularly the cationic polyacrylamide. The objective of this study was to determine the extent of interaction of anionic and cationic polyacrylamide with each shale sample in the presence of additives such as salts.展开更多
Through hydrothermal process, the chrysanthemum-like ZnO particles are prepared with zinc acetate dihydrate （Zn（CH3COO）2·2H2O） and sodium hydroxide （NaOH） used as main resources under the different concentr...Through hydrothermal process, the chrysanthemum-like ZnO particles are prepared with zinc acetate dihydrate （Zn（CH3COO）2·2H2O） and sodium hydroxide （NaOH） used as main resources under the different concentrations of surfactant polyacrylamide （PAM）. The microstructure, morphology and the electromagnetic properties of the as-prepared products are characterized by high-resolution transmission electron microscopy （HRTEM）, field emission environment scanning electron microscope （FEESEM） and microwave vector network analyzer, respectively. The experimental results indicate that the as-prepared products are ZnO single crystalline with hexagona wurtzite structure, that the values of slenderness ratio Ld are different in different PAM concentrations, and that the good magnetic loss property is found in the ZnO products, and the average magnetic loss tangent tan δu increases with PAM concentration increasing, while the dielectric loss tangent tan ~e decreases.展开更多
BREAST fibromatosis is a rare kind of lesion. The average incidence is about 2-4 per million every year} So far there have been about 100 cases reported altogether.2 In this report, we describe a case of breast fibrom...BREAST fibromatosis is a rare kind of lesion. The average incidence is about 2-4 per million every year} So far there have been about 100 cases reported altogether.2 In this report, we describe a case of breast fibromatosis developed after hydrophilic polyacrylamide gel （HPG） injection for breast augmentation. By reviewing the literature, the possible pathogenesis of this case and the proper treatment strategy are investigated.展开更多
The degradation of partially hydrolyzed polyacrylamide(HPAM) found in alkaline/surfactant/polymer flooding sewage was investigated using Fenton-type reagents. Different Fenton reagent treatments for HPAM degradation w...The degradation of partially hydrolyzed polyacrylamide(HPAM) found in alkaline/surfactant/polymer flooding sewage was investigated using Fenton-type reagents. Different Fenton reagent treatments for HPAM degradation were compared. The effects of pH, hydrogen peroxide(H_(2)O_(2)), ferrous ion(Fe^(2+)), and tartaric ion(C_(4)H_(4)O_(6)^(2-)) concentrations were studied. The degradation reaction occurred within a wide range of pH(3–9). The HPAM degradation performance of photo-Fenton processes using solar light and UV were compared with that of the Fenton process. The degradation rate was found to be strongly dependent on the H_(2)O_(2)/Fe^(2+)/C_(4)H_(4)O_(6)^(2-)molar ratio. The HPAM degradation efficiency was 90%, and the chemical oxygen demand removal efficiency was 85%. HPAM could be degraded into a compound with a lower molecular weight, but it was difficult to achieve complete mineralization to CO_(2). The presence of intermediate products hindered further oxidation in the Fenton process.展开更多
Polyacrylamide microspheres have been suc- cessfully used to reduce water production in reservoirs, but it is impossible to distinguish polyacrylamide microspheres from polyacrylamide that is used to enhance oil recov...Polyacrylamide microspheres have been suc- cessfully used to reduce water production in reservoirs, but it is impossible to distinguish polyacrylamide microspheres from polyacrylamide that is used to enhance oil recovery and is already present in production fluids. In order to detect polyacrylamide microspheres in the reservoir pro- duced fluid, fluorescent polyacrylamide microspheres P（AM-BA-AMCO）, which fluoresce under ultraviolet irradiation, were synthesized via an inverse suspension polymerization. In order to keep the particle size distribu- tion in a narrow range, the synthesis conditions of the polymerization were studied, including the stirring speed and the concentrations of initiator, NaaCO3, and dispersant. The bonding characteristics of microspheres were deter- mined by Fourier transform infrared spectroscopy. The surface morphology of these microspheres was observed under ultraviolet irradiation with an inverse fluorescence microscope. A laboratory evaluation test showed that the fluorescent polymer microspheres had good water swelling capability, thus they had the ability to plug and migrate in a sand pack. The plugging rate was 99.8 % and the residual resistance coefficient was 800 after microsphere treatment in the sand pack. Furthermore, the fluorescent microspheres and their fragments were accurately detected under ultra- violet irradiation in the produced fluid, even though theyhad experienced extrusion and deformation in the sand pack.展开更多
The synthesis and characterization of a novel macroporous silica derived size exclusion chromatography （SEC） packing for quantitative analysis of high molecular weight （MW） polyacrylamide （PAM） are presented. Us...The synthesis and characterization of a novel macroporous silica derived size exclusion chromatography （SEC） packing for quantitative analysis of high molecular weight （MW） polyacrylamide （PAM） are presented. Using this packing, a fast, sensitive and reproducible approach for quantitation of super high-MW PAM in demanding enhanced oil recovery （EOR） waters was developed and the effect of synthesis parameters on the properties of resultant materials was investigated. These parameters include salt addition, reaction temperature and duration, activation condition of functional groups on the silica surface, as well as the reaction cycles required for optimal silica modification. Moreover, SEC analysis conditions, such as mobile phase composition, flow rate, detection and sample preparation, were also explored and an optimal analysis protocol was developed. Under this optimized SEC analysis conditions, the synthesized macroporous materials proved satisfactory for quantification of PAM with average MW up to 22 million Daltons. An SEC analysis required less than few minutes with a detection limit of 1 ng, a linear response range of 0.1 to 75 mg/L with squared R value of 0.99 and reproducibility better than 9.2% RSD （relative standard deviation）. The analysis of PAM in highly saline oilfield production water containing interfering high MW polymeric surfactants indicated the recovery ranges from 92.5% to 110.1% for 1.0 mg/L PAM and 94.2% to 103.8% for 50 mg/L PAM solution. This study presented for the ftrst time that the reliable quantization of high MW PAM in highly demanding EOR waters can be achieved by SEC.展开更多
This work presents an approach to build a high-performance, low-viscous and replaceable separation matrix, semi-crosslinked polyacrylamide （semi-CPA） capillary gel electrophoresis. Non- denatured basic proteins, suc...This work presents an approach to build a high-performance, low-viscous and replaceable separation matrix, semi-crosslinked polyacrylamide （semi-CPA） capillary gel electrophoresis. Non- denatured basic proteins, such as lysozyme, cytochrome C, ribonuclease A and trypsin were separa- ted. The impacts of monomer and cross-linker concentrations on protein separation were studied, and the ability of dynamic capillary inner wall coating was demonstrated. The UV absorption interfer- ence by semi-CPA gel matrix was successfully overcome by a partial filling technique, which results in sensitivity 20 times higher than other protein separation method. The excellent separation ability, reproducibility and dynamic coating ability made semi-CPA an ideal separation media in both capillar- y electrophoresis and microfluidic chip separation scheme.展开更多
基金the Research Partnership to Secure Energy for America (RPSEA)Oklahoma State University Chemical Engineering Department for partial support of this project
文摘Partially hydrolyzed polyacrylamide（HPAM）as the main component of slickwater fracturing fluid is a shear-sensitive polymer,which suffers from mechanical degradation at turbulent flow rates.Five different concentrations of HPAM as well as mixtures of polyacrylamide/xanthan gum were prepared to investigate the possibility of improving shear stability of HPAM.Drag reduction（DR）measurements were performed in a closed flow loop.For HPAM solutions,the extent of DR increased from 30%to67%with increasing HPAM concentration from 100 to1000 wppm.All the HPAM solutions suffered from mechanical degradation and loss of DR efficiency over the shearing period.Results indicated that the resistance to shear degradation increased with increasing polymer concentration.DR efficiency of 600 wppm xanthan gum（XG）was 38%,indicating that XG was not as good a drag reducer as HPAM.But with only 6%DR decline,XG solution exhibited a better shear stability compared to HPAM solutions.Mixed HPAM/XG solutions initially exhibited greater DR（40%and 55%）compared to XG,but due to shear degradation,DR%dropped for HPAM/XG solutions.Compared to 200 wppm HPAM solution,addition of XG did not improve the drag reduction efficiency of HPAM/XG mixed solutions though XG slightly improved the resistance against mechanical degradation in HPAM/XG mixed polymer solutions.
基金supported by Anhui University of Science and Technology Youth Fund(No.QN201415)Anhui Province Science and Technology Key Project(No.1301042130)College Students’ Innovation and Entrepreneurship Training Program(No.201810361079)
文摘In this work, non-thermal plasma has been applied to treat polyacrylamide（PAM） wastewater.We have investigated the influence of the rule of PAM wastewater initial pH, solution concentration and discharge time, discharge voltage on chemical oxygen demand（COD）degradation rate. At the same time, the effect of pH and discharge time on the viscosity removal rate of PAM solution was also studied. Then, the effect of pH on the viscosity removal rate of1.0 gl-1 PAM solution was studied separately. Through orthogonal test, the factors affecting the COD degradation rate of PAM wastewater were determined as follows: discharge time > discharge voltage > solution concentration > wastewater initial pH. The COD highest removal rate of PAM wastewater reached 85.74%, when the optimal conditions are as follows:discharge voltage 40 k V, discharge time 5 h, solution concentration 1.0 gl-1, pH 1.5. This research provides some basic data and new theoretical basis for PAM wastewater purification.
基金financial support from the National Natural Science Foundation of China (Grants Nos. 51203186, U1362101 and 51173203)the Converging Research Center Program funded by Korean Ministry of Education (2013K000415)the Project of Science and Technology Program for Basic Research of Qingdao (No. 121-4-7-(6)-jch)
文摘In this paper, cationic polyacrylamide microspheres （CPAM） were synthesized using acrylamide （AM） and methacryloyloxyethyl trimethyl ammonium chloride （TMAEMC） as monomers, ammonium sulfate as dispersant, poly（acryloyloxyethyl trimethyl ammonium chloride） （PAETAC） as dispersion stabilizer, and ammonium persulfate as initiator. The synthetic method was dispersion polymerization. The effects of monomer ratio （AM/TMAEMC）, dispersant concentration, and dispersion stabilizer dosage on dispersion polymerization were systematically studied to determine the optimal preparation conditions. The structure and viscosity of the synthesized polymer were characterized by FTIR and capillary viscometry, respectively, and the particle sizes and distribution of the polymer microspheres were characterized by microscopy and dynamic light scattering, respectively. Finally, flow tests were conducted to measure the permeability reduction performance of the microspheres at various concentrations in sand packs with different permeability. Results show that CPAM emulsion of a solids content of 1 wt% has excellent performance in low-to-medium permeability formations （〈 1,000 mD）, and the efficiency may reach above 90%.
文摘A temperature-resistant, salt-tolerant polyacrylamide, hydrophobically associating polymer （HAP）, was synthesized in the State Key Laboratory of Heavy Oil Processing. The rheological behavior of HAP solution was investigated by means of flow experiments in porous media and by using a HAAKE RS600 rheometer. The results of Nuclepore membrane filtration showed that filtration time increased sharply when the critical association concentration was reached. Shear rate had a greater impact on viscosity and shear stress with increasing HAP concentration. The HAP solution with a concentration of 100 mg/L （salinity 32,868 mg/L） exhibited negative thixotropy. However, at the same salinity the HAP solution showed thixotropy and its viscosity became greater when the polymer concentration increased to 1,500 mg/L. The flow experiments in cemented core samples indicated that the resistance factor and residual resistance factor of the HAP solution were 31.8 and 12 when polymer concentration and salinity were 1,500 mg/L, 32,868 mg/L at 85℃ respectively, which is favorable for flooding application. Such factors of partially hydrolyzed polyaerylamide 3530S were merely 3.14 and 1.71, so it could not be applied to polymer flooding in the oilfield with high temperature and high salinity.
文摘Interaction of polymer-containing injected fluids with shale is a widely studied phenomenon, but much is still unknown about the interaction of charged polyacrylamides such as anionic and cationic polyacrylamides with shale. The nature of interaction of charged polyacrylamides with shale is not well understood, especially from the perspective of assessing the potential for polyacrylamides to cause formation damage. Zeta potential and rheological measurements were made for Chattanooga and Pride Mountain shales suspended in polyacrylamide solutions with and without inorganic salts and tetramethyl ammonium chloride（TMAC）. The change in zeta potential and viscosity with time was recorded. The magnitude of decrease in the absolute value of zeta potential with time is indicative of adsorption of polymer on the surface of shale and serves as a measure of the extent of polymer interaction with shale. The salts that were used in this study are potassium chloride（KCl）, sodium chloride（Na Cl）. This study quantified the interaction of anionic and cationic polyacrylamide with different North American shales.From the experimental results, it was determined that the polyacrylamides can interact strongly with shale, particularly the cationic polyacrylamide. The objective of this study was to determine the extent of interaction of anionic and cationic polyacrylamide with each shale sample in the presence of additives such as salts.
基金Project supported by the National High Technology Research and Development Program of China (Grant No 2005A000200)the Xi’an Applied Materials Innovation Fund, China (Grant No XA-AM-200712)the Innovative Experiment Program for Chinese Students (Grant No State 200721)
文摘Through hydrothermal process, the chrysanthemum-like ZnO particles are prepared with zinc acetate dihydrate （Zn（CH3COO）2·2H2O） and sodium hydroxide （NaOH） used as main resources under the different concentrations of surfactant polyacrylamide （PAM）. The microstructure, morphology and the electromagnetic properties of the as-prepared products are characterized by high-resolution transmission electron microscopy （HRTEM）, field emission environment scanning electron microscope （FEESEM） and microwave vector network analyzer, respectively. The experimental results indicate that the as-prepared products are ZnO single crystalline with hexagona wurtzite structure, that the values of slenderness ratio Ld are different in different PAM concentrations, and that the good magnetic loss property is found in the ZnO products, and the average magnetic loss tangent tan δu increases with PAM concentration increasing, while the dielectric loss tangent tan ~e decreases.
文摘BREAST fibromatosis is a rare kind of lesion. The average incidence is about 2-4 per million every year} So far there have been about 100 cases reported altogether.2 In this report, we describe a case of breast fibromatosis developed after hydrophilic polyacrylamide gel （HPG） injection for breast augmentation. By reviewing the literature, the possible pathogenesis of this case and the proper treatment strategy are investigated.
基金the Northeast Petroleum University Youth Science Foundation (No. 2019QNL-35)Guiding Science and Technology Plan Project of Daqing (No. zd-2021-39)。
文摘The degradation of partially hydrolyzed polyacrylamide(HPAM) found in alkaline/surfactant/polymer flooding sewage was investigated using Fenton-type reagents. Different Fenton reagent treatments for HPAM degradation were compared. The effects of pH, hydrogen peroxide(H_(2)O_(2)), ferrous ion(Fe^(2+)), and tartaric ion(C_(4)H_(4)O_(6)^(2-)) concentrations were studied. The degradation reaction occurred within a wide range of pH(3–9). The HPAM degradation performance of photo-Fenton processes using solar light and UV were compared with that of the Fenton process. The degradation rate was found to be strongly dependent on the H_(2)O_(2)/Fe^(2+)/C_(4)H_(4)O_(6)^(2-)molar ratio. The HPAM degradation efficiency was 90%, and the chemical oxygen demand removal efficiency was 85%. HPAM could be degraded into a compound with a lower molecular weight, but it was difficult to achieve complete mineralization to CO_(2). The presence of intermediate products hindered further oxidation in the Fenton process.
基金supported by the National Natural Science Foundation of China (No.21273286)Doctoral Program Foundation of the Education Ministry (No.20130133110005)
文摘Polyacrylamide microspheres have been suc- cessfully used to reduce water production in reservoirs, but it is impossible to distinguish polyacrylamide microspheres from polyacrylamide that is used to enhance oil recovery and is already present in production fluids. In order to detect polyacrylamide microspheres in the reservoir pro- duced fluid, fluorescent polyacrylamide microspheres P（AM-BA-AMCO）, which fluoresce under ultraviolet irradiation, were synthesized via an inverse suspension polymerization. In order to keep the particle size distribu- tion in a narrow range, the synthesis conditions of the polymerization were studied, including the stirring speed and the concentrations of initiator, NaaCO3, and dispersant. The bonding characteristics of microspheres were deter- mined by Fourier transform infrared spectroscopy. The surface morphology of these microspheres was observed under ultraviolet irradiation with an inverse fluorescence microscope. A laboratory evaluation test showed that the fluorescent polymer microspheres had good water swelling capability, thus they had the ability to plug and migrate in a sand pack. The plugging rate was 99.8 % and the residual resistance coefficient was 800 after microsphere treatment in the sand pack. Furthermore, the fluorescent microspheres and their fragments were accurately detected under ultra- violet irradiation in the produced fluid, even though theyhad experienced extrusion and deformation in the sand pack.
文摘The synthesis and characterization of a novel macroporous silica derived size exclusion chromatography （SEC） packing for quantitative analysis of high molecular weight （MW） polyacrylamide （PAM） are presented. Using this packing, a fast, sensitive and reproducible approach for quantitation of super high-MW PAM in demanding enhanced oil recovery （EOR） waters was developed and the effect of synthesis parameters on the properties of resultant materials was investigated. These parameters include salt addition, reaction temperature and duration, activation condition of functional groups on the silica surface, as well as the reaction cycles required for optimal silica modification. Moreover, SEC analysis conditions, such as mobile phase composition, flow rate, detection and sample preparation, were also explored and an optimal analysis protocol was developed. Under this optimized SEC analysis conditions, the synthesized macroporous materials proved satisfactory for quantification of PAM with average MW up to 22 million Daltons. An SEC analysis required less than few minutes with a detection limit of 1 ng, a linear response range of 0.1 to 75 mg/L with squared R value of 0.99 and reproducibility better than 9.2% RSD （relative standard deviation）. The analysis of PAM in highly saline oilfield production water containing interfering high MW polymeric surfactants indicated the recovery ranges from 92.5% to 110.1% for 1.0 mg/L PAM and 94.2% to 103.8% for 50 mg/L PAM solution. This study presented for the ftrst time that the reliable quantization of high MW PAM in highly demanding EOR waters can be achieved by SEC.
基金Supported by the Key Project in the National Science ＆ Tech- nology Pillar Program During the Eleventh Five-Year Plan Pe- riod （2009BAK59B02）
文摘This work presents an approach to build a high-performance, low-viscous and replaceable separation matrix, semi-crosslinked polyacrylamide （semi-CPA） capillary gel electrophoresis. Non- denatured basic proteins, such as lysozyme, cytochrome C, ribonuclease A and trypsin were separa- ted. The impacts of monomer and cross-linker concentrations on protein separation were studied, and the ability of dynamic capillary inner wall coating was demonstrated. The UV absorption interfer- ence by semi-CPA gel matrix was successfully overcome by a partial filling technique, which results in sensitivity 20 times higher than other protein separation method. The excellent separation ability, reproducibility and dynamic coating ability made semi-CPA an ideal separation media in both capillar- y electrophoresis and microfluidic chip separation scheme.
