摘要
为满足超轻量化光学系统近衍射极限的性能要求,利用先进的CAE仿真与现代高性能SiC制作工艺,研究Φ500 mm SiC反射镜的超轻量化反射镜结构。首先,通过对比现有反射镜常用材料和制作工艺,选取反射镜材料。针对圆形对称反射镜结构特性,采用全等刚度设计,结合集成优化方法,设计反射镜结构形式。同时,采用背部支撑结构,完成反射镜组件结构设计。仿真结果表明:主镜质量小于5 kg,面密度小于20 kg/m^2。3个方向自重变形下及4℃温升工况下的面形误差(RMS值)均优于λ/50;主镜组件的一阶谐振频率不小于120 Hz,动态响应分析表明最薄弱处应力小于100 MPa。满足反射镜设计要求,轻量化效果显著,结构稳定可靠。
To meet the performance requirements of ultra-lightweightΦ500 mm-reflector optical system in near diffraction limit,the structure of the reflector is studied using advanced CAE simulation and modern high-performance SiC fabrication technology.Firstly,mirror materials were selected by comparing the common materials and manufacturing processes of existing mirrors.Then,with regards to the structural characteristics of circular symmetrical reflectors,the structure of proposed reflector was designed based on integrated optimization of the full stiffness method.Finally,the reflector assembly was designed with a back-support structure.The simulation results show that the mass of proposed primary mirror is less than 5 kg and the surface density is less than 20 kg/m^2.The surface errors(RMS value)of the three directions of dead weight deformation at 4℃temperature rise are less thanλ/50.The first-order resonance frequency of the primary mirror assembly is no less than 120 Hz and the stress at the weakest point as measured by dynamic response analysis is less than 100 MPa.The structural optimization of the mirror meets its design requirements,with a remarkable lightweight effect and a structure that is both stable and reliable.
作者
赵宇
苏成志
赵贵军
杨光
ZHAO Yu;SU Cheng-zhi;ZHAO Gui-jun;YANG Guang(College of Mechanical Engineering,Changchun University of Science and Technology,Changchun 130000,China;Changchun Up Optotech Co.,Ltd.,Changchun 130000,China)
出处
《中国光学》
EI
CAS
CSCD
北大核心
2020年第6期1352-1361,共10页
Chinese Optics
基金
国家自然科学基金资助项目(No.11873046)。
关键词
超轻量化
背部支撑
有限元仿真
等刚度设计
集成优化
ultra-lightweight
back support
finite element simulation
equal stiffness design
integrated optimization
作者简介
赵宇(1992—),男,吉林松原人,硕士研究生,2014年于长春理工大学获得学士学位,现为长春理工大学机电工程学院硕士研究生,主要从事空间光机结构方面的研究。E-mail:zy_012269@163.com;Corresponding author:苏成志(1977—),男,吉林桦甸人,教授,博士生导师,2004年、2010年于长春理工大学分别获得硕士、博士学位,2013年于美国密歇根州立大学做访问学者,现为长春理工大学人工智能研究院副院长,主要从事现代检测技术及智能机器人研究。E-mail:chengzhi_su@126.com。
