期刊文献+

井下流量控制阀金属密封仿真研究 被引量:2

Simulation Study on Metal Seal for the Interval Control Valve
在线阅读 下载PDF
导出
摘要 智能井的井下流量控制阀中的金属密封对于其可靠性具有重要的影响。针对具有圆度误差的金属密封和滑套的密封副(以下简称为金属密封副),利用ABAQUS研究了介质压力和初始过盈量对其接触应力的影响。研究发现:①当金属密封副的2个椭圆截面长轴正交或重合时,接触应力沿接触环面分别呈“W”型或“M”型曲线分布。2种曲线上波峰和波谷处的接触应力的最值与密封面上的平均接触应力均随着介质压力、初始过盈量和滑套圆度误差的增加而增加;②当金属密封副的2个椭圆长轴夹角θ为15~75°时,接触应力分布曲线的波峰和波谷的最值和密封面上的平均接触应力先减小后增加,且与θ的关系曲线均关于θ=45°线近似对称。 The metal seal in the interval control valve(ICV)of intelligent well has an important influence on the ICV reliability.In this paper,ABAQUS was used to study the influence of medium pressure and initial interference on the contact stress between the metal seal ring and the sliding sleeve,both of which have roundness error.The results show that:firstly,when the major axes of the two elliptical sections of the metal seal pair are orthogonal or coincident,the contact stress along the contact ring surface presents"W"or"M"curves respectively.The maximum contact stress at the wave peak and trough and average contact stress along the seal face increase with the increase of the medium pressure,the initial interference and the roundness error of the sliding sleeve.Secondly,when the angle between the two ellipse major axes of the metal seal pair is between 15°and 75°,the maximum contact stress at the wave peak and trough and average contact stress along the seal face decrease first and then increase.The relationship curve between three contact stresses and the angle is approximately symmetrical about the line ofθ=45°.
作者 杨仪伟 朱宏武 何东升 郑严 许亮斌 何玉发 李川 YANG Yiwei;ZHU Hongwu;HE Dongsheng;ZHENG Yan;XU Liangbin;HE Yufa;LI Chuan(College of Mechanical and Transportation Engineering, China University of Petroleum (Beijing),Beijing 102249,China;Electro-mechanic Engineering College,Southwest Petroleum University,Chengdu 610500,China;CNOOC Research Institute Co.,Ltd., Beijing 100028,China)
出处 《石油矿场机械》 2020年第3期24-32,共9页 Oil Field Equipment
基金 “十三五”国家科技重大专项“深水测试风险评估与完井及井筒完整性研究”(2016ZX05028001-006)。
关键词 智能井 井下流量控制阀 金属密封 圆度误差 接触应力 intelligent well interval control valve metal seal pair roundness error contact stress
作者简介 杨仪伟(1981-),男,山东泰安人,讲师,博士研究生,研究方向为智能完井及机械密封,E-mail:yangyw@swpu.edu.cn。
  • 相关文献

参考文献6

二级参考文献41

  • 1刘合,黄建鑫,王秀喜.一种超弹性合金密封体的实验研究[J].实验力学,2004,19(2):144-149. 被引量:6
  • 2潘仁度.微观密封学概论[J].润滑与密封,1994,19(5):11-14. 被引量:24
  • 3刘毅,徐学忠.机械结构渗漏的机理分析及解决措施[J].润滑与密封,2005,30(2):176-178. 被引量:4
  • 4胡玉志,刘克勇,王黎阳.Φ90mm金属封隔器的研制[J].河南石油,2005,19(2):66-67. 被引量:6
  • 5胡玉志,王锐.大通径金属密封封隔器的研究与应用[J].石油矿场机械,2005,34(4):78-80. 被引量:15
  • 6van Dort R. Metal-to-metal seals meet downhole hazard demands [ J ] . Journal of Petroleum Technology, 2009 (1): 24 -26.
  • 7Garfield G L, Mackenzie G. Recent metal-to-metal seal- ing technology for zonal isolation: Applications demon- strates potential for use in hostile HPHT environments- zonal[R] . SPE 105854, 2007.
  • 8Garfield G, Mackenzie G. Metal-to-metal sealing tech- nology: Bridging the gap between conventional and high-expansion zonal isolation applications [ R ] . SPE 107107. 2007.
  • 9Adam M, Lundemo K, Mackenzie G, et al. Develop- ment and installation of a high-pressure-rated bridge pl- ug with metal-to-metal sealing system [ R] . SPE 99770, 2006.
  • 10Chapman I C, Ng K S, Nor N M, et al. Wireline de- ployed metal sealing bridge plug system: operational learning curve and subsequent redevelopment [R] . SPE 113891, 2008.

共引文献68

同被引文献11

引证文献2

二级引证文献13

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部