期刊文献+

某碳质金精矿富氧焙烧—氯化浸出试验研究 被引量:3

Experimental research on oxygen-enriched roasting-chlorination leaching process of a carbonaceous gold concentrate
在线阅读 下载PDF
导出
摘要 某碳质金精矿直接氰化浸出金浸出率很低,小于30%,为进一步提高金浸出率,针对碳质金精矿性质,进行了富氧焙烧—氯化浸出试验研究。结果表明:与常规氧化焙烧相比,富氧焙烧降低了焙烧温度,缩短了焙烧时间;富氧焙烧最佳焙烧温度550℃~600℃,氧气体积分数50%,焙烧时间2.0 h,在此条件下,碳、硫去除率均在95%以上;焙砂采用M-NaCl氯化浸出,在最佳浸出条件为固液比1∶6,浸液pH=3,浸出剂用量8 kg/t,试样粒度62~75μm,浸出时间4 h时,金浸出率可达92.50%,相对于试样直接氯化浸出时有显著提高;表明富氧焙烧—氯化浸出工艺是可行的。 Since direct cyanide leaching of a carbonaceous gold concentrate has a very low leaching rate,which is lower than 30%,experimental study was carried on oxygen-enriched roasting-chlorination leaching of a carbonaceous gold concentrate to improve gold leaching rate.The results showed that compared with conventional oxidation roasting,oxygen-enriched roasting not only could reduce the roasting temperature,but also could shorten the roasting time;when the optimum oxygen-enriched roasting temperature is 550℃-600℃,the optimum oxygen volume fraction is 50%,and the optimum roasting time is 2.0 h,both the deprivation rate of carbon and sulfur is over 95%in the optimum conditions.The calcine is chlorinated in M-NaCl.The results proved that the extraction rate of gold could reach 92.50%,when the optimum leaching conditions were:the solid-liquid ratio was 1∶6,the lixivium pH was 3,amount of leaching agent was 8 kg/t,test sample particle size was 62-75μm and the leaching time was 4 hours,when the test sample was directly subjected to chlorination leaching.The process of oxygen-enriched roasting-chlorination leaching is feasible.
作者 杨凤云 Yang Fengyun(Langfang China Railway Geophysical Exploration Co.,Ltd.)
出处 《黄金》 CAS 2020年第2期57-61,共5页 Gold
关键词 碳质金精矿 富氧焙烧 氯化浸出 有机氯化剂 氯化钠 carbonaceous gold concentrate oxygen-enriched roasting chlorination leaching organic chlorinating agent NaCl
作者简介 杨凤云(1987—),女,河南新乡人,工程师,从事岩矿分析工作,河北省廊坊市廊万路9号,廊坊市中铁物探勘察有限公司,065000,E-mail:yfy1236@126.com。
  • 相关文献

参考文献5

二级参考文献41

共引文献90

同被引文献50

引证文献3

二级引证文献13

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部