期刊文献+

置氢对TB8钛合金室温压缩性能的影响 被引量:2

Effect of hydrogenation on room temperature compression properties of TB8 titanium alloy
在线阅读 下载PDF
导出
摘要 通过热氢处理技术在钛合金中引入临时元素氢,可以改变钛合金的相组成,进而改变钛合金的力学性能和加工性能。文章采用压缩实验研究置氢对TB8合金室温压缩性能的影响,并利用OM、XRD和DTA等方法研究固态置氢后TB8钛合金微观组织和相变的演变过程。结果表明,氢降低了TB8合金的β相转变温度,在氢含量为0.7wt%时组织完全转变成β相,置氢后合金中生成了δ氢化物和ω相;氢对TB8合金的塑性影响较小,但由于β相的软化作用,使置氢后合金的屈服强度低于原始合金,应变硬化能力随氢含量的增加而逐渐增强,主要是由氢原子及氢化物对位错的阻碍作用所致。 Hydrogen is usually used as a temporary component to adjust the mechanical and processing properties of titanium alloys through modifying the microstructure. The effect of hydrogenation on the room temperature compression properties was studied with compression test, and the microstructure evolution and phase transformation of TB8 titanium alloy after hydrogenation were investigated using OM, XRD and DTA. The results revealed that hydrogen reduced β transus temperature, the structure was completely transformed into β phase when hydrogen content reached 0.7wt%, and δ hydride and ω phase appeared in specimens after hydrogenation, Hydrogen had a relatively small impact on plasticity of TB8 alloy. However, due to the softening effect of the β phase, the yield strength after hydrogenation was lower than the original alloy. Strain hardening capacity gradually increased with the increasing of hydrogen content, mainly because the hydrogen atoms and hydrides hindered dislocation motion.
出处 《塑性工程学报》 CAS CSCD 北大核心 2012年第6期15-18,共4页 Journal of Plasticity Engineering
基金 国家自然科学基金资助项目(51175137) 安徽省优秀青年科技基金资助项目(10040606Y21) 中央高校基本科研业务费专项资金资助项目(2010HGBZ0612)
关键词 热氢处理 TB8钛合金 组织 压缩性能 thermohydrogen treatment TB8 titanium alloy structure compression property
作者简介 李萍E-mail:cisi_1314@126.com.作者简介:李萍,女,1973年生,黑龙江双城人,合肥工业大学,教授,博士生导师
  • 相关文献

参考文献8

二级参考文献18

  • 1俞汉清,曾卫东,周义刚,王慈校,徐好义.Ti—17合金β锻造研究[J].西北工业大学学报,1995,13(3):340-344. 被引量:10
  • 2周义刚,张宝昌.钛合金近β锻造研究[J].航空学报,1989,10(1). 被引量:20
  • 3王庆如,张庆玲,陈玉文,储俊鹏,戴美云,王鲁峰,杨瑜生,黄仲田,王世洪,沈桂琴.Ti-15-3钛合金的应用研究[J].材料工程,1996(12):16-19. 被引量:9
  • 4朱知寿.Ti-15Mo-2.7Nb-3Al-0.2Si钛合金强度与韧性匹配关系研究[J].金属学报,1999,35(1):159-159.
  • 5PoirierJP 关德林.晶体的高温塑性变形[M].大连:大连理工大学出版社,1989..
  • 6Ronald TMF. J Adv Mater Processess, 1993, 9: 24.
  • 7Gorelik S S.金属和合金的再结晶[M].北京:机械工业出版社,1985.369-390
  • 8Ezugwu E O,Wang Z M.Titanimalloy and their machinability:a review[J].J of Materials Processing Technology,1997,68:262-274.
  • 9Lee W S,Lin C F.High-temperature deformation behavior of Ti6Al4V alloy evaluated by high strain-rate compression tests[J].J of Materials Processing Technology,1998,75:127-136.
  • 10McQueen H J,Jonas J J.Recovery and recrystallization in the hotworking of aluminum alloys[A].Arsenault R J.Treatise on Materials Science and Technology (Vol 6):Plastic Deformation of Materials[C].New York:Academic Press,1975.393-493.

共引文献151

同被引文献16

引证文献2

二级引证文献3

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部