期刊文献+

空间电压脉宽调制SVPWM的原理及DSP的实现 被引量:10

Principle of SVPWM and its realization based on DSP
在线阅读 下载PDF
导出
摘要 针对空间电压矢量脉宽调制过程中存在的问题,采用理论推演与软件设计方法,在介绍了SVPWM的基本原理的基础上,利用TI公司的DSP电机控制芯片TMS320LF2407设计了SVPWM的实现方法,并给出了变频调速系统的全数字化实现。通过对永磁同步电机进行控制仿真实验,得到的结果表明此方法是切实可行的,控制系统具有优良的动静态性能,较高的控制效果,有广泛的应用前景。 In view of the problem of SPWM, the theoretic illustration and software design method is used. In addition to the introduction of the basic principle of SVPWM ,the method of realizing SVPWM by TI' s DSP motor controller TMS320LF2407 is designed, and a full-digital solution of SVPWM control is presented. The results of experiments with PMSM indicate that the proposed method is feasible and the control system has excellent dynamic and static performances and high control effect, which has broad application prospects.
出处 《辽宁工程技术大学学报(自然科学版)》 EI CAS 北大核心 2007年第6期898-900,共3页 Journal of Liaoning Technical University (Natural Science)
基金 国家自然科学基金资助项目(50607007)
关键词 空间电压矢量 脉宽调制 数字信号处理器 voltage space vector pulse width modulation digital signal processor
作者简介 候利民(1976-),男,河北承德人,博士研究生,讲师,主要从事电力电子与电力传动的研究
  • 相关文献

参考文献5

二级参考文献17

  • 1王兆安(译) 日本电气学会.电力半导体变流电路[M].北京:机械工业出版社,1993..
  • 2康勇.高频大功率SPWM逆变电源输出电压控制技术研究:博士论文[M].华中理工大学,1994..
  • 3[1]Satoshi Ogasawara.A novel PWM scheme of voltage source inverters based on space vector theory[C]. EPE Aachen 1989:1199-1202.
  • 4[2]Alberto J P.Software pulsewidth modulation for up control of AC drives[J].IEEE Trans on IA,1986,22(4):519-524.
  • 5[3]Murray A,Kettle P. Towards a single chip DSP based motor control solution[J]. Proceeding PCIM96, Nuremberg,1996,5(5):315-326.
  • 6刘志晖,张青,陈坚.一种新颖的三相 SPWM 技术[J].电力电子技术,1997,31(2):1-5. 被引量:20
  • 7陈伯时.交流调速系统[M].北京:机械工业出版社,2000..
  • 8康勇,博士学位论文,1994年
  • 9王兆安(译),电力半导体变流电路,1993年
  • 10Bowes,S. R,Yen-Shin Lai. The relationship between space-vector modulation and regular-sampled PWM [ J ]. IEEE Transactions on Industrial Electronics, 1997,44 (5): 670 ~ 679.

共引文献567

同被引文献87

引证文献10

二级引证文献29

相关作者

内容加载中请稍等...

相关机构

内容加载中请稍等...

相关主题

内容加载中请稍等...

浏览历史

内容加载中请稍等...
;
使用帮助 返回顶部