The stochastic resonance behavior of coupled stochastic resonance(SR)system with time-delay under mass and frequency fluctuations was studied.Firstly,the approximate system model of the time-delay system was obtained ...The stochastic resonance behavior of coupled stochastic resonance(SR)system with time-delay under mass and frequency fluctuations was studied.Firstly,the approximate system model of the time-delay system was obtained by the theory of small time-delay approximation.Then,the random average method and Shapiro-Loginov algorithm were used to calculate the output amplitude ratio of the two subsystems.The simulation analysis shows that increasing the time-delay and the input signal amplitude appropriately can improve the output response of the system.Finally,the system is applied to bearing fault diagnosis and compared with the stochastic resonance system with random mass and random frequency.The experimental results show that the coupled SR system taking into account the actual effect of time-delay and couple can more effectively extract the frequency of the fault signal,and thus realizing the diagnosis of the fault signal,which has important engineering application value.展开更多
An adaptive modulation （AM） algorithm is proposed and the application of the adapting algorithm together with low-density parity-check （LDPC） codes in multicarrier systems is investigated. The AM algorithm is base...An adaptive modulation （AM） algorithm is proposed and the application of the adapting algorithm together with low-density parity-check （LDPC） codes in multicarrier systems is investigated. The AM algorithm is based on minimizing the average bit error rate （BER） of systems, the combination of AM algorithm and LDPC codes with different code rates （half and three-fourths） are studied. The proposed AM algorithm with that of Fischer et al is compared. Simulation results show that the performance of the proposed AM algorithm is better than that of the Fischer＇s algorithm. The results also show that application of the proposed AM algorithm together with LDPC codes can greatly improve the performance of multicarrier systems. Results also show that the performance of the proposed algorithm is degraded with an increase in code rate when code length is the same.展开更多
Two adaptive power and bit loading algorithms to maximize the throughput of MIMO-OFDM systems in frequency selective fading environment are proposed. The two algorithms allocate bit based on maximizing the overall thr...Two adaptive power and bit loading algorithms to maximize the throughput of MIMO-OFDM systems in frequency selective fading environment are proposed. The two algorithms allocate bit based on maximizing the overall throughput. One algorithm allocates power based on guaranteeing that the bit error rate （BER） of each sub-carrier and the total allocated power remain below a target BER threshold and a power threshold, respectively; another one allocates power based on guaranteeing that the mean BER of sub-carriers and the total allocated power remain below a target BER threshold and a power threshold, respectively. The simulation results show that the proposed algorithms can achieve faster throughput with lower computational complexity, which indicates that the proposed algorithms are effective when compared to some existing algorithms.展开更多
View synthesis is an important building block in three dimension（3D） video processing and communications.Based on one or several views,view synthesis creates other views for the purpose of view prediction（for compr...View synthesis is an important building block in three dimension（3D） video processing and communications.Based on one or several views,view synthesis creates other views for the purpose of view prediction（for compression） or view rendering（for multiview-display）.The quality of view synthesis depends on how one fills the occlusion area as well as how the pixels are created.Consequently,luminance adjustment and hole filling are two key issues in view synthesis.In this paper,two views are used to produce an arbitrary virtual synthesized view.One view is merged into another view using a local luminance adjustment method,based on local neighborhood region for the calculation of adjustment coefficient.Moreover,a maximum neighborhood spreading strength hole filling method is presented to deal with the micro texture structure when the hole is being filled.For each pixel at the hole boundary,its neighborhood pixels with the maximum spreading strength direction are selected as candidates;and among them,the pixel with the maximum spreading strength is used to fill the hole from boundary to center.If there still exist disocclusion pixels after once scan,the filling process is repeated until all hole pixels are filled.Simulation results show that the proposed method is efficient,robust and achieves high performance in subjection and objection.展开更多
A compressed sensing（CS） based channel estimation algorithm is proposed by using the delay-Doppler sparsity of the fast fading channel.A compressive basis expansion channel model with sparsity in both time and frequ...A compressed sensing（CS） based channel estimation algorithm is proposed by using the delay-Doppler sparsity of the fast fading channel.A compressive basis expansion channel model with sparsity in both time and frequency domains is given.The pilots in accordance with a novel random pilot matrix in both time and frequency domains are sent to measure the delay-Doppler sparsity channel.The relatively nonzero channel coefficients are tracked by random pilots at a sampling rate significantly below the Nyquist rate.The sparsity channels are estimated from a very limited number of channel measurements by the basis pursuit algorithm.The proposed algorithm can effectively improve the channel estimation performance when the number of pilot symbols is reduced with improvement of throughput efficiency.展开更多
Pedestrian positioning system(PPS)using wearable inertial sensors has wide applications towards various emerging fields such as smart healthcare,emergency rescue,soldier positioning,etc.The performance of traditional ...Pedestrian positioning system(PPS)using wearable inertial sensors has wide applications towards various emerging fields such as smart healthcare,emergency rescue,soldier positioning,etc.The performance of traditional PPS is limited by the cumulative error of inertial sensors,complex motion modes of pedestrians,and the low robustness of the multi-sensor collaboration structure.This paper presents a hybrid pedestrian positioning system using the combination of wearable inertial sensors and ultrasonic ranging(H-PPS).A robust two nodes integration structure is developed to adaptively combine the motion data acquired from the single waist-mounted and foot-mounted node,and enhanced by a novel ellipsoid constraint model.In addition,a deep-learning-based walking speed estimator is proposed by considering all the motion features provided by different nodes,which effectively reduces the cumulative error originating from inertial sensors.Finally,a comprehensive data and model dual-driven model is presented to effectively combine the motion data provided by different sensor nodes and walking speed estimator,and multi-level constraints are extracted to further improve the performance of the overall system.Experimental results indicate that the proposed H-PPS significantly improves the performance of the single PPS and outperforms existing algorithms in accuracy index under complex indoor scenarios.展开更多
The effect of introducing attenuation on Lamb wave dispersion curves is studied in this paper. Attenuation is introduced to a three-layered composite plate by an adhesive bond layer with viscous behavior. No changes a...The effect of introducing attenuation on Lamb wave dispersion curves is studied in this paper. Attenuation is introduced to a three-layered composite plate by an adhesive bond layer with viscous behavior. No changes are required to the transfer matrix formulation for the propagation of elastic waves. By introduction of a complex wavenumber, the model can be used to the propagation of attenuative Lamb waves. Numerical examples for a three-layered aluminium-epoxy-aluminium plate show that attenuation values of each mode in plates are related not only to attenuation, but also to the thickness of the bonded layer, which is in agreement with practical situations.展开更多
Maximal-ratio transmission systems with transmit antenna selection is investigated. According to the order statistics of channel fiat fading coefficients, the closed-form expressions axe derived for average SNR with a...Maximal-ratio transmission systems with transmit antenna selection is investigated. According to the order statistics of channel fiat fading coefficients, the closed-form expressions axe derived for average SNR with any amount of RF chains and average BER with two RF chains, respectively. The algorithm for calculating the minimum of total transmit antennas is presented in terms of reduced RF chains. The method of quantizing transmit precoders is employed in this study to decrease feedback information. Simulation results demonstrate the superiority of the proposed systems under full and quantized transmit precoders. The SNR of the proposed systems has been less degraded by the quantization of transmit precoder than that of pure maximal-ratio transmission systems.展开更多
In this paper, the 40-Gbps orthogonal frequency division multiple access(OFDMA) technology enabled by subcarrier allocation in the form of integrated architecture for the intra-cell is proposed in the downlink transmi...In this paper, the 40-Gbps orthogonal frequency division multiple access(OFDMA) technology enabled by subcarrier allocation in the form of integrated architecture for the intra-cell is proposed in the downlink transmission passive broadband optical access system. The data-carrying subcarriers in the inverse fast Fourier transform/fast Fourier transform(IFFT/FFT) size of1 024 points are successfully divided into three sub-channels,in which each sub-channel has 256 useful subcarriers, by using adaptive dynamic bandwidth allocation(DBA). Taking the inherent advantages of M-ary quadrature amplitude modulation(MQAM)modulation mechanism into account, the performance of the absolutely identical MQAM format over the different sub-channels for the downstream OFDMA-passive optical network(PON) is investigated based on the intensity modulation direct detection(IMDD) system by simulations. The results show that three parallel4 QAM or 16 QAM or 64 QAM OFDMA data, which are transmitted over three sub-channels, is more suitable for different sub-channel allocations, respectively. In addition, comparing with single port4/16/64 QAM OFDM over the same access system, the receiver sensitivity economizes – 0.6 d Bm, 0.6 d Bm, 4.6 d Bm at the bit error rate(BER) value of 10-3 respectively.展开更多
An improved single image dehazing method based on dark channel prior and wavelet transform is proposed. This pro-posed method employs wavelet transform and guided filter instead of the soft matting procedure to estima...An improved single image dehazing method based on dark channel prior and wavelet transform is proposed. This pro-posed method employs wavelet transform and guided filter instead of the soft matting procedure to estimate and refine the depth map of haze images. Moreover, a contrast enhancement method based on just noticeable difference （JND） and quadratic function is adopted to enhance the contrast for the dehazed image, since the scene radiance is usual y not as bright as the atmospheric light, and the dehazed image looks dim. The experimental results show that the proposed approach can effectively enhance the haze ima-ge and is wel suitable for implementing on the surveil ance and obstacle detection systems.展开更多
A new algorithm is proposed for completing the missing parts caused by the removal of foreground or background elements from an image of natural scenery in a visually plausible way. The major contributions of the prop...A new algorithm is proposed for completing the missing parts caused by the removal of foreground or background elements from an image of natural scenery in a visually plausible way. The major contributions of the proposed algorithm are： （1） for most natural images, there is a strong orientation of texture or color distribution. So a method is introduced to compute the main direction of the texture and complete the image by limiting the search to one direction to carry out image completion quite fast; （2） there exists a synthesis ordering for image completion. The searching order of the patches is defined to ensure the regions with more known information and the structures should be completed before filling in other regions; （3） to improve the visual effect of texture synthesis, an adaptive scheme is presented to determine the size of the template window for capturing the features of various scales. A number of examples are given to demonstrate the effectiveness of the proposed algorithm.展开更多
Attenuative Lamb wave propagation in adhesively bonded anisotropic composite plates is introduced. The isotropic adhesive exhibits viscous behavior to stimulate the poor curing of the middle layer. Viscosity is assume...Attenuative Lamb wave propagation in adhesively bonded anisotropic composite plates is introduced. The isotropic adhesive exhibits viscous behavior to stimulate the poor curing of the middle layer. Viscosity is assumed to vary linearly with frequency, implying that attenuation per wavelength is constant. Attenuation can be implemented in the analysis through modification of elastic properties of isotropic adhesive. The new properties become complex, but cause no further complications in the analysis. The characteristic equation is the same as that used for the elastic plate case, except that both real and imaginary parts of the wave number (i.e., the attenuation) must be computed. Based on the Lowe’s solution in finding the complex roots of characteristic equation, the effect of longitudinal and shear attenuation coefficients of the middle adhesive layer on phase velocity dispersion curves and attenuation dispersion curves of Lamb waves propagating in bonded anisotropic composites is visualized numerically.展开更多
基金Project(61771085)supported by the National Natural Science Foundation of ChinaProject(KJQN 201900601)supported by the Research Project of Chongqing Educational Commission,China。
文摘The stochastic resonance behavior of coupled stochastic resonance(SR)system with time-delay under mass and frequency fluctuations was studied.Firstly,the approximate system model of the time-delay system was obtained by the theory of small time-delay approximation.Then,the random average method and Shapiro-Loginov algorithm were used to calculate the output amplitude ratio of the two subsystems.The simulation analysis shows that increasing the time-delay and the input signal amplitude appropriately can improve the output response of the system.Finally,the system is applied to bearing fault diagnosis and compared with the stochastic resonance system with random mass and random frequency.The experimental results show that the coupled SR system taking into account the actual effect of time-delay and couple can more effectively extract the frequency of the fault signal,and thus realizing the diagnosis of the fault signal,which has important engineering application value.
基金the National Natural Science Foundation of China (60496313)
文摘An adaptive modulation （AM） algorithm is proposed and the application of the adapting algorithm together with low-density parity-check （LDPC） codes in multicarrier systems is investigated. The AM algorithm is based on minimizing the average bit error rate （BER） of systems, the combination of AM algorithm and LDPC codes with different code rates （half and three-fourths） are studied. The proposed AM algorithm with that of Fischer et al is compared. Simulation results show that the performance of the proposed AM algorithm is better than that of the Fischer＇s algorithm. The results also show that application of the proposed AM algorithm together with LDPC codes can greatly improve the performance of multicarrier systems. Results also show that the performance of the proposed algorithm is degraded with an increase in code rate when code length is the same.
基金the National Natural Science Foundation of China (60496313).
文摘Two adaptive power and bit loading algorithms to maximize the throughput of MIMO-OFDM systems in frequency selective fading environment are proposed. The two algorithms allocate bit based on maximizing the overall throughput. One algorithm allocates power based on guaranteeing that the bit error rate （BER） of each sub-carrier and the total allocated power remain below a target BER threshold and a power threshold, respectively; another one allocates power based on guaranteeing that the mean BER of sub-carriers and the total allocated power remain below a target BER threshold and a power threshold, respectively. The simulation results show that the proposed algorithms can achieve faster throughput with lower computational complexity, which indicates that the proposed algorithms are effective when compared to some existing algorithms.
基金supported by the National Natural Science Foundation of China(61075013)
文摘View synthesis is an important building block in three dimension（3D） video processing and communications.Based on one or several views,view synthesis creates other views for the purpose of view prediction（for compression） or view rendering（for multiview-display）.The quality of view synthesis depends on how one fills the occlusion area as well as how the pixels are created.Consequently,luminance adjustment and hole filling are two key issues in view synthesis.In this paper,two views are used to produce an arbitrary virtual synthesized view.One view is merged into another view using a local luminance adjustment method,based on local neighborhood region for the calculation of adjustment coefficient.Moreover,a maximum neighborhood spreading strength hole filling method is presented to deal with the micro texture structure when the hole is being filled.For each pixel at the hole boundary,its neighborhood pixels with the maximum spreading strength direction are selected as candidates;and among them,the pixel with the maximum spreading strength is used to fill the hole from boundary to center.If there still exist disocclusion pixels after once scan,the filling process is repeated until all hole pixels are filled.Simulation results show that the proposed method is efficient,robust and achieves high performance in subjection and objection.
基金supported by the National Natural Science Foundation of China(60972056)the Innovation Foundation of Shanghai Education Committee(09ZZ89)Shanghai Leading Academic Discipline Project and STCSM(S30108and08DZ2231100)
文摘A compressed sensing（CS） based channel estimation algorithm is proposed by using the delay-Doppler sparsity of the fast fading channel.A compressive basis expansion channel model with sparsity in both time and frequency domains is given.The pilots in accordance with a novel random pilot matrix in both time and frequency domains are sent to measure the delay-Doppler sparsity channel.The relatively nonzero channel coefficients are tracked by random pilots at a sampling rate significantly below the Nyquist rate.The sparsity channels are estimated from a very limited number of channel measurements by the basis pursuit algorithm.The proposed algorithm can effectively improve the channel estimation performance when the number of pilot symbols is reduced with improvement of throughput efficiency.
基金supported by the National Natural Science Foundation of China under(Grant No.52175531)in part by the Science and Technology Research Program of Chongqing Municipal Education Commission under Grant(Grant Nos.KJQN202000605 and KJZD-M202000602)。
文摘Pedestrian positioning system(PPS)using wearable inertial sensors has wide applications towards various emerging fields such as smart healthcare,emergency rescue,soldier positioning,etc.The performance of traditional PPS is limited by the cumulative error of inertial sensors,complex motion modes of pedestrians,and the low robustness of the multi-sensor collaboration structure.This paper presents a hybrid pedestrian positioning system using the combination of wearable inertial sensors and ultrasonic ranging(H-PPS).A robust two nodes integration structure is developed to adaptively combine the motion data acquired from the single waist-mounted and foot-mounted node,and enhanced by a novel ellipsoid constraint model.In addition,a deep-learning-based walking speed estimator is proposed by considering all the motion features provided by different nodes,which effectively reduces the cumulative error originating from inertial sensors.Finally,a comprehensive data and model dual-driven model is presented to effectively combine the motion data provided by different sensor nodes and walking speed estimator,and multi-level constraints are extracted to further improve the performance of the overall system.Experimental results indicate that the proposed H-PPS significantly improves the performance of the single PPS and outperforms existing algorithms in accuracy index under complex indoor scenarios.
文摘The effect of introducing attenuation on Lamb wave dispersion curves is studied in this paper. Attenuation is introduced to a three-layered composite plate by an adhesive bond layer with viscous behavior. No changes are required to the transfer matrix formulation for the propagation of elastic waves. By introduction of a complex wavenumber, the model can be used to the propagation of attenuative Lamb waves. Numerical examples for a three-layered aluminium-epoxy-aluminium plate show that attenuation values of each mode in plates are related not only to attenuation, but also to the thickness of the bonded layer, which is in agreement with practical situations.
基金the National Natural Science Foundation of China (60472103)Shanghai Excellent Academic Leader Project (05XP14027)Shanghai Leading Academic Discipline Project(T0102).
文摘Maximal-ratio transmission systems with transmit antenna selection is investigated. According to the order statistics of channel fiat fading coefficients, the closed-form expressions axe derived for average SNR with any amount of RF chains and average BER with two RF chains, respectively. The algorithm for calculating the minimum of total transmit antennas is presented in terms of reduced RF chains. The method of quantizing transmit precoders is employed in this study to decrease feedback information. Simulation results demonstrate the superiority of the proposed systems under full and quantized transmit precoders. The SNR of the proposed systems has been less degraded by the quantization of transmit precoder than that of pure maximal-ratio transmission systems.
基金supported by the National Natural Science Foundation of China(61771082 61801065+3 种基金 61871062)the China Scholarship Council(201908500139)the Science and Technology Research Program of Chongqing Municipal Education Commission(KJQN201800615KJQN201800609)
文摘In this paper, the 40-Gbps orthogonal frequency division multiple access(OFDMA) technology enabled by subcarrier allocation in the form of integrated architecture for the intra-cell is proposed in the downlink transmission passive broadband optical access system. The data-carrying subcarriers in the inverse fast Fourier transform/fast Fourier transform(IFFT/FFT) size of1 024 points are successfully divided into three sub-channels,in which each sub-channel has 256 useful subcarriers, by using adaptive dynamic bandwidth allocation(DBA). Taking the inherent advantages of M-ary quadrature amplitude modulation(MQAM)modulation mechanism into account, the performance of the absolutely identical MQAM format over the different sub-channels for the downstream OFDMA-passive optical network(PON) is investigated based on the intensity modulation direct detection(IMDD) system by simulations. The results show that three parallel4 QAM or 16 QAM or 64 QAM OFDMA data, which are transmitted over three sub-channels, is more suitable for different sub-channel allocations, respectively. In addition, comparing with single port4/16/64 QAM OFDM over the same access system, the receiver sensitivity economizes – 0.6 d Bm, 0.6 d Bm, 4.6 d Bm at the bit error rate(BER) value of 10-3 respectively.
基金This research was supported by the Natural Science Foundation of Fujian Province under Grant Nos. 2015J01012 and 2015J01019.
文摘An improved single image dehazing method based on dark channel prior and wavelet transform is proposed. This pro-posed method employs wavelet transform and guided filter instead of the soft matting procedure to estimate and refine the depth map of haze images. Moreover, a contrast enhancement method based on just noticeable difference （JND） and quadratic function is adopted to enhance the contrast for the dehazed image, since the scene radiance is usual y not as bright as the atmospheric light, and the dehazed image looks dim. The experimental results show that the proposed approach can effectively enhance the haze ima-ge and is wel suitable for implementing on the surveil ance and obstacle detection systems.
文摘A new algorithm is proposed for completing the missing parts caused by the removal of foreground or background elements from an image of natural scenery in a visually plausible way. The major contributions of the proposed algorithm are： （1） for most natural images, there is a strong orientation of texture or color distribution. So a method is introduced to compute the main direction of the texture and complete the image by limiting the search to one direction to carry out image completion quite fast; （2） there exists a synthesis ordering for image completion. The searching order of the patches is defined to ensure the regions with more known information and the structures should be completed before filling in other regions; （3） to improve the visual effect of texture synthesis, an adaptive scheme is presented to determine the size of the template window for capturing the features of various scales. A number of examples are given to demonstrate the effectiveness of the proposed algorithm.
文摘Attenuative Lamb wave propagation in adhesively bonded anisotropic composite plates is introduced. The isotropic adhesive exhibits viscous behavior to stimulate the poor curing of the middle layer. Viscosity is assumed to vary linearly with frequency, implying that attenuation per wavelength is constant. Attenuation can be implemented in the analysis through modification of elastic properties of isotropic adhesive. The new properties become complex, but cause no further complications in the analysis. The characteristic equation is the same as that used for the elastic plate case, except that both real and imaginary parts of the wave number (i.e., the attenuation) must be computed. Based on the Lowe’s solution in finding the complex roots of characteristic equation, the effect of longitudinal and shear attenuation coefficients of the middle adhesive layer on phase velocity dispersion curves and attenuation dispersion curves of Lamb waves propagating in bonded anisotropic composites is visualized numerically.
