Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifi...Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.展开更多
The article presents problems related to mechanical protection of vehicles with different add-on armours against chemical,biological and radiological contamination.This applies to vehicles with additional passive,reac...The article presents problems related to mechanical protection of vehicles with different add-on armours against chemical,biological and radiological contamination.This applies to vehicles with additional passive,reactive and hybrid protection in the form of cassettes against piercing with anti-tank projectiles,piercing with their kinetic energy of impact,and as a result of chemical energy of shaped charges as well as explosively formed projectiles.It has been shown how increased ballistic protection of these vehicles at the same time reduces their decontaminability in various places of the vehicle due to the increased additional surface of the vehicle with cassettes.Prevention of contamination of these cassettes has been presented as a way of reducing hard to reach surface for decontamination and a method of insulating construction elements(stands),fixing these cassettes to the vehicle,from the environment to prevent contact with contaminated liquids and dusts.The selection of appropriate materials is shown,which may affect the improvement of the decontamination efficiency of the vehicle with such cassettes.This applies to the use of materials with low absorption of chemical warfare agents,which prevent the accumulation of large amounts of these agents on contaminated surfaces and improve the effectiveness of decontamination.It also shows how to ensure better access of the disinfectant to as much of the vehicle surface as possible,covered with cassettes that have been contaminated.It shows how a vehicle,in particular with such cassettes,can provide protection against radar detection when Radar Absorbent Material is used on vehicle cassettes.展开更多
文摘Penetration characteristic(size and shape of penetration craters made in high hardness ARMSTAL 30PM steel) of shaped charge jets formed after detonations of modified PG-7VM warheads was analyzed in the article. Modifications consisted in removing the frontal part of the grenade(fuse, ballistic cap and conductive cone) and introducing of the liner cavity filling made of polyacetal copolymer POM-C. The filings in the form of solid cones with three different heights(33%, 66% and 100% of H-the height of original PG-7VM liner) were placed inside of the hollow cone shaped charge liner. As opposed to the vast majority of previously published works(in which warhead optimization studies were focused on increasing of the depth of penetration in rolled homogeneous armor steel) the main aim of the presented modifications was to maximize the damage ratio(diameters of craters, inlet and outlet holes) of target perforated by shaped charge jet at the cost of the loss of part of the jet penetration capability. According to the best knowledge of the authors such approach to the use of the old PG-7VM warheads has not been analyzed so far. Taking into consideration high stock levels of PG-7VM warheads, and the fact that they are continuously being replaced by more efficient and more sophisticated high-explosive anti-tank warheads, it seems reasonable to look for alternate applications of the warheads withdrawn from the service. Thanks to the introduction of proposed modifications the warheads could be used by special forces or other assault units as directional mines or statically detonated cutting shaped charges as well as by combat engineers as universal charges used in various types of engineering or sapper works. The research included experimental penetration tests and their numerical reproduction in the LS-Dyna software with the simulation methodology defined and validated in previous works of the authors.Small differences(average error = 10-20%) were identified between the experimental and numerical results(dimensions of craters made in steel targets were compared) what confirmed the reliability of the modelling methodology and enabled its use for further optimization of the shapes of fillings. Within the analyzed variants of warheads modifications maximum diameters of penetration craters were obtained for the filling of the height of h = 2/3H. The diameters of holes in individual steel plates were increased by 164%, 70%, 65%(for the first, second and third plate, respectively) in relation to the variant without filling. The results of the study indicated that with the use of different materials of fillings and their various heights it is possible to control the shape of penetration craters pierced in the steel targets.
文摘The article presents problems related to mechanical protection of vehicles with different add-on armours against chemical,biological and radiological contamination.This applies to vehicles with additional passive,reactive and hybrid protection in the form of cassettes against piercing with anti-tank projectiles,piercing with their kinetic energy of impact,and as a result of chemical energy of shaped charges as well as explosively formed projectiles.It has been shown how increased ballistic protection of these vehicles at the same time reduces their decontaminability in various places of the vehicle due to the increased additional surface of the vehicle with cassettes.Prevention of contamination of these cassettes has been presented as a way of reducing hard to reach surface for decontamination and a method of insulating construction elements(stands),fixing these cassettes to the vehicle,from the environment to prevent contact with contaminated liquids and dusts.The selection of appropriate materials is shown,which may affect the improvement of the decontamination efficiency of the vehicle with such cassettes.This applies to the use of materials with low absorption of chemical warfare agents,which prevent the accumulation of large amounts of these agents on contaminated surfaces and improve the effectiveness of decontamination.It also shows how to ensure better access of the disinfectant to as much of the vehicle surface as possible,covered with cassettes that have been contaminated.It shows how a vehicle,in particular with such cassettes,can provide protection against radar detection when Radar Absorbent Material is used on vehicle cassettes.
