The Editor-in-Chief has retracted this article [1] because Figures 11 and 12 appear to be identical with Figures 3 and 4respectively from a previously published article [2].Sehrish MUKHTAR,Waqas ASGHAR,Zubair BUTT,Zah...The Editor-in-Chief has retracted this article [1] because Figures 11 and 12 appear to be identical with Figures 3 and 4respectively from a previously published article [2].Sehrish MUKHTAR,Waqas ASGHAR,Zubair BUTT,Zaheer ABBAS,Mudaser ULLAH and Rana ATTA-UR-REHMAN did not respond to correspondence about this retraction.展开更多
Combustion within small motors is key in the application-specific development of nanothermite-based micro-energetic systems. This study evaluates the performance of nanothermite mixtures in a converging-diverging nozz...Combustion within small motors is key in the application-specific development of nanothermite-based micro-energetic systems. This study evaluates the performance of nanothermite mixtures in a converging-diverging nozzle and an open tube. Mixtures were prepared using nano-aluminum(n-Al),potassium perchlorate(KClO_(4)), and different carbon nanomaterials(CNMs) including graphene-oxide(GO), reduced GO, carbon nanotubes(CNTs) and nanofibers(CNFs). The mixtures were packed at different densities and ignited by laser beam. Performance was measured using thrust measurement,high-speed imaging, and computational fluid dynamics modeling, respectively. Thrust, specific impulse(ISP), volumetric impulse(ISV), as well as normalized energy were found to increase notably with CNM content. Two distinctive reaction regimes(fast and slow) were observed in combustion of low and high packing densities(20% and 55%TMD), respectively. Total impulse(IFT) and ISPwere maximized in the 5%GO/Al/KClO_4 mixture, producing 7.95 m N·s and 135.20 s respectively at 20%TMD, an improvement of 57%compared to a GO-free sample(5.05 m N·s and 85.88 s). CFD analysis of the motors over predicts the thrust generated but trends in nozzle layout and packing density agree with those observed experimentally;peak force was maximized by reducing packing density and using an open tube. The numerical force profiles fit better for the nozzle cases than the open tube scenarios due to the rapid nature of combustion. This study reveals the potential of GO in improving oxygenated salt-based nanothermites,and further demonstrates their applicability for micro-propulsion and micro-energetic applications.展开更多
Stainless steel(SS)grade 316L is used for orthopedic implants due to its biocompatibility;yet the effort should be done to minimize the carcinogenic and inflammatory effects related to SS 316L implants.In this researc...Stainless steel(SS)grade 316L is used for orthopedic implants due to its biocompatibility;yet the effort should be done to minimize the carcinogenic and inflammatory effects related to SS 316L implants.In this research,aluminide coating of Al–Si alloy on SS 316L is characterized by using optical microscopy,energy dispersive spectroscopy(EDS),nano-indentation and corrosion testing technique.Hot dip aluminizing process is used to coat the SS 316L specimens at 765°C for 2 min immersion time.Half of the specimens are also diffusion treated in a Muffle furnace at 550°C for 4 h to produce diffused specimens of SS 316L.Microstructural examination shows the formation of flat coating/substrate interface due to Si addition.EDS analysis confirms the formation of complex intermetallic at the coating/substrate interface which finally results in increasing the hardness and corrosion resistance properties of coating.展开更多
文摘The Editor-in-Chief has retracted this article [1] because Figures 11 and 12 appear to be identical with Figures 3 and 4respectively from a previously published article [2].Sehrish MUKHTAR,Waqas ASGHAR,Zubair BUTT,Zaheer ABBAS,Mudaser ULLAH and Rana ATTA-UR-REHMAN did not respond to correspondence about this retraction.
基金financial funding from the Egyptian governmentthe financial funding from the NSERC Discovery grant。
文摘Combustion within small motors is key in the application-specific development of nanothermite-based micro-energetic systems. This study evaluates the performance of nanothermite mixtures in a converging-diverging nozzle and an open tube. Mixtures were prepared using nano-aluminum(n-Al),potassium perchlorate(KClO_(4)), and different carbon nanomaterials(CNMs) including graphene-oxide(GO), reduced GO, carbon nanotubes(CNTs) and nanofibers(CNFs). The mixtures were packed at different densities and ignited by laser beam. Performance was measured using thrust measurement,high-speed imaging, and computational fluid dynamics modeling, respectively. Thrust, specific impulse(ISP), volumetric impulse(ISV), as well as normalized energy were found to increase notably with CNM content. Two distinctive reaction regimes(fast and slow) were observed in combustion of low and high packing densities(20% and 55%TMD), respectively. Total impulse(IFT) and ISPwere maximized in the 5%GO/Al/KClO_4 mixture, producing 7.95 m N·s and 135.20 s respectively at 20%TMD, an improvement of 57%compared to a GO-free sample(5.05 m N·s and 85.88 s). CFD analysis of the motors over predicts the thrust generated but trends in nozzle layout and packing density agree with those observed experimentally;peak force was maximized by reducing packing density and using an open tube. The numerical force profiles fit better for the nozzle cases than the open tube scenarios due to the rapid nature of combustion. This study reveals the potential of GO in improving oxygenated salt-based nanothermites,and further demonstrates their applicability for micro-propulsion and micro-energetic applications.
基金sponsored and funded by Metallurgy and Materials Engineering Department,College of Engineering and Emerging Technologies, University of the Punjab (grant no.PU/ASR&TD/ RG-348 dated 26-1-2012)
文摘Stainless steel(SS)grade 316L is used for orthopedic implants due to its biocompatibility;yet the effort should be done to minimize the carcinogenic and inflammatory effects related to SS 316L implants.In this research,aluminide coating of Al–Si alloy on SS 316L is characterized by using optical microscopy,energy dispersive spectroscopy(EDS),nano-indentation and corrosion testing technique.Hot dip aluminizing process is used to coat the SS 316L specimens at 765°C for 2 min immersion time.Half of the specimens are also diffusion treated in a Muffle furnace at 550°C for 4 h to produce diffused specimens of SS 316L.Microstructural examination shows the formation of flat coating/substrate interface due to Si addition.EDS analysis confirms the formation of complex intermetallic at the coating/substrate interface which finally results in increasing the hardness and corrosion resistance properties of coating.
