5-amino-4-nitrobenzo[1,2-c:3,4-c']bis([1,2,5]oxadiazole)1,6-dioxide(CL-18)exhibits significant potential as an initiating explosive.However,its current synthesis process remains non-scalable due to low yields and ...5-amino-4-nitrobenzo[1,2-c:3,4-c']bis([1,2,5]oxadiazole)1,6-dioxide(CL-18)exhibits significant potential as an initiating explosive.However,its current synthesis process remains non-scalable due to low yields and safety risks.In this study,we have developed a simple and safe synthetic route for CL-18.It was synthesized from 3,5-dihaloanisole in a four-step reaction with an overall yield exceeding 60%,surpassing all reported yields in the literature.Subsequently,recrystallization of CL-18 was successfully achieved by carefully selecting appropriate solvents and antisolvents to reduce its mechanical sensitivity.Ultimately,when DMF-ethanol was employed as the recrystallization solvent system,satisfactory product yield(>90%)and reduced mechanical sensitivity(IS=15 J;FS=216 N)were obtained.Additionally,CL-18 is derived from the rearrangement of oxygen atoms on i-CL-18 furoxan,and a comparative analysis of their physicochemical properties was conducted.The thermal stability of both compounds is similar,with onset decomposition temperatures recorded at 186 and 182℃respectively.Similarly,they exhibit 5 s breaking point temperatures of 236 and 237℃.Additionally,we present novel insights into the positional-isomerization-laser-ignition performance of CL-18 and its isomer i-CL-18 using laser irradiation for the first time.Remarkably,our findings demonstrate that i-CL-18 exhibits enhanced laser sensitivity,as it can be directly ignited by a 1064 nm wavelength laser,whereas CL-18 lacks this characteristic.展开更多
Detonation performance is crucial for evaluating the power of high explosives(HEs),and the equation of state(EOS)that accurately describes the high-temperature,high-pressure,and high-temperature,medium-pressure states...Detonation performance is crucial for evaluating the power of high explosives(HEs),and the equation of state(EOS)that accurately describes the high-temperature,high-pressure,and high-temperature,medium-pressure states of detonation products is key to assessing the damage efficiency of these energetic materials.This article examines the limitations of the VLW EOS in representing the thermodynamic states of explosive detonation gas products under high-temperature and medium-to high-pressure conditions.A new gas EOS for detonation products,called VHL(Virial-Han-Long),is proposed.The accuracy of VHL in describing gas states under high-temperature and medium-to high-pressure conditions is verified,and its performance in evaluating explosive detonation and working capabilities is explored.The results demonstrate that VHL exhibits high precision in calculating detonation performance.Subsequently,the detonation performance of three new HEs(ICM-101,ONC,and TNAZ)was calculated and compared to traditional HEs(TATB,CL-20,and HMX).The results indicate that ONC has superior detonation performance compared to the other explosives,while ICM-101 shows a detonation velocity similar to CL-20 but with slightly lower detonation pressure.The detonation characteristics of TNAZ are comparable to those of the standard HE HMX.From the perspective of products,considering the comprehensive work performance(mechanical work and detonation heat),both ONC and ICM-101demonstrate relatively superior performance.展开更多
A new dimensionless number is proposed for dynamic plastic deformation analysis of clamped circular plates under underwater explosion loads by introducing dimensional analysis method to the basic dynamical governing e...A new dimensionless number is proposed for dynamic plastic deformation analysis of clamped circular plates under underwater explosion loads by introducing dimensional analysis method to the basic dynamical governing equations of circular plates.The relation between dimensionless final plastic deformation of circular plates and the new dimensionless number is established based on massive underwater explosion test data.Meanwhile,comparative analysis was discussed with two other published dimensionless parameters which indicated the new dimensionless number proposed in this paper is more effective and extensive to predict the dynamic plastic response of circular plates under underwater explosion condition.展开更多
The energy release of energetic composites is severely limited by the inert alumina(Al_(2)O_(3))layer on the surface of aluminum(Al).Polytetrafluoroethylene(PTFE)could eliminate Al_(2)O_(3)layer due to its highly elec...The energy release of energetic composites is severely limited by the inert alumina(Al_(2)O_(3))layer on the surface of aluminum(Al).Polytetrafluoroethylene(PTFE)could eliminate Al_(2)O_(3)layer due to its highly electronegativity and oxidability of fluorine.However,adding PTFE particles would weaken interfacial interactions resulted in poor mechanical properties and interfacial exothermic reaction.Herein,a bridging Al-PTFE as fuel and interfacial reinforcing agent was added and used to prepare LLM-105/AlPTFE microspheres,achieving both high energy output and excellent mechanical properties.The energy release and combustion reaction performance of LLM-105/Al-PTFE microspheres are significantly improved due to high reaction heat and increased interfacial reaction area of Al-PTFE.The maximum pressure and pressurization rate of LLM-105/Al-PTFE microspheres are 164.06 kPa and 29.88 kPa/s,respectively,which are 40.11%and 16.67%higher than those of physical mixed samples.Furthermore,the tensile strength and compressive strength of LLM-105/Al-PTFE microspheres are 100.40%and 26.47%higher than those of LLM-105/Al.This work provides a new approach to improve the energy release and mechanical properties for energetic composites.展开更多
Aluminum(Al)powder is widely applied in thermobaric explosives due to its high energy density and favorable reaction kinetics.However,the inert oxide layer(Al_(2)O_(3))on Al particles limits combustion reactivity and ...Aluminum(Al)powder is widely applied in thermobaric explosives due to its high energy density and favorable reaction kinetics.However,the inert oxide layer(Al_(2)O_(3))on Al particles limits combustion reactivity and energy efficiency.Fluoride-based surface modification has been developed as an effective approach to address this issue.Here,four classical fluoropolymers(F11,F14,PVDF,PTFE)are employed as coatings to prepare core-shell Al/Fluoropolymer.The combustion experimental results demonstrate that the core-shell Al/PTFE exhibits the highest flame propagation rate(52.88 mm·ms^(-1))and pressure output(109.02 k Pa)performance.Consequently,core-shell Al/PTFE is selected as a high-energy fuel to prepare RDX/Al/PTFE microspheres via the emulsion and solvent evaporation method,which can enhance the energy performance of RDX.The effects of the core-shell Al/PTFE ratio and RDX content on the combustion heat and pressure output are systematically investigated.The peak pressure reaches a maximum of 187.8 k Pa when the mass ratio of RDX,Al,and PTFE is 60:25:10.Additionally,RDX/Al/PTFE microspheres exhibit significantly higher laser-induced air shock velocities,detonation heat,and detonation pressure than those of pure RDX and RDX/Al.The mechanism underlying the enhanced reactivity and energetic performance is attributed to the ability of PTFE to etch the inert Al_(2)O_(3)shell on the surface of Al particles,thereby improving post-combustion reactions and significantly increasing the overall energy output of RDX explosives.This work offers a novel design strategy for high-energy structural thermobaric explosives for the practical applications.展开更多
Nowadays, ultrafine explosives are widely used in military fields. Ultrafine 2,2',4,4',6,6'-hexanitrostilbene(HNS) has emerged as an optimal primer for explosion foil initiators due to its excellent therma...Nowadays, ultrafine explosives are widely used in military fields. Ultrafine 2,2',4,4',6,6'-hexanitrostilbene(HNS) has emerged as an optimal primer for explosion foil initiators due to its excellent thermal stability and high-voltage short-pulse initiation performance. However, the solid phase ripening of ultrafine HNS leads to a degradation in its impact detonation performance. Previous studies have indicated that residual dimethyl formamide(DMF), which is present in ultrafine HNS prepared using the recrystallization method, affects ultrafine HNS ripening. The mechanism of residual solvent effects on solid phase ripening of ultrafine HNS is unclear. In this work, the specific surface area(SSA) derived from small angle X-ray scattering(SAXS) was utilized for kinetic fitting analysis to explore the mechanism by which residual solvents enhance the solid phase ripening of ultrafine HNS. The results of the SSA measured by insitu SAXS under conditions of 150℃ for 40 h revealed that the sample with 0.2% residual DMF exhibited a 21.51% decrease in SSA, whereas the sample with only 0.04% residual DMF showed a decrease of 15.66%.Furthermore, the higher amounts of residual DMF accelerated the reduction in SSA with time. Kinetic fitting analysis demonstrated that reducing residual DMF would lower both the activation energy and the pre-exponential factor, consequently decreasing the rate constant of solid phase ripening. The mechanism was speculated that it primarily facilitated the Ostwald ripening(OR). Additionally, contrast variation small angle X-ray scattering(CV-SAXS) confirmed that coating of ultrafine HNS particles is an effective method for inhibiting ripening, significantly reducing both the rate and extent of ripening of ultrafine HNS. This study predicts how residual solvents impact the solid phase ripening process of ultrafine HNS and proposes strategies for enhancing the long-term stability of ultrafine explosives.展开更多
This study investigates the paradoxical detonation behavior of TKX-50,a nitrogen-rich energetic material,exhibiting higher detonation velocities but lower metal acceleration ability compared to HMX.Through experimenta...This study investigates the paradoxical detonation behavior of TKX-50,a nitrogen-rich energetic material,exhibiting higher detonation velocities but lower metal acceleration ability compared to HMX.Through experimental measurements and theoretical calculations,we propose a novel three-factor competition mechanism to explain this phenomenon.TKX-50-based PBX formulations achieved detonation velocities up to 9100 m/s,surpassing HMX-based counterparts.However,cylinder expansion tests revealed a 15%reduction in metal acceleration ability.Thermochemical measurements showed lower detonation heat for TKX-50(4900 J/g)versus HMX(5645 J/g).Our mechanism involves:(1)compositional effects prevailing at high pressures;(2)Energy release becoming essential as pressure drops;(3)Pressure-dependent product composition evolution functioning at low pressure.VLW code calculations unveiled a"crossover"in Hugoniot curves,lending support to this mechanism.This study furnishes a new framework for comprehending the performance of nitrogen-rich energetic materials,with significant implications for the design and optimization of future high-energy density materials.展开更多
Realizing effective enhancement in the thermally conductive performance of polymer bonded explosives(PBXs) is vital for improving the resultant environmental adaptabilities of the PBXs composites. Herein, a kind of pr...Realizing effective enhancement in the thermally conductive performance of polymer bonded explosives(PBXs) is vital for improving the resultant environmental adaptabilities of the PBXs composites. Herein, a kind of primary-secondary thermally conductive network was designed by water-suspension granulation, surface coating, and hot-pressing procedures in the graphene-based PBXs composites to greatly increase the thermal conductive performance of the composites. The primary network with a threedimensional structure provided the heat-conducting skeleton, while the secondary network in the polymer matrix bridged the primary network to increase the network density. The enhancement efficiency in the thermally conductive performance of the composites reached the highest value of 59.70% at a primary-secondary network ratio of 3:1. Finite element analysis confirmed the synergistic enhancement effect of the primary and secondary thermally conductive networks. This study introduces an innovative approach to designing network structures for PBX composites, significantly enhancing their thermal conductivity.展开更多
Herein,a first example of energetic-energetic cocrystal polymorphs with a 1:1 M ratio was discovered by cocrystallizing CL-20(2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane)with 1,3-DNP(1,3-dinitropyrazole...Herein,a first example of energetic-energetic cocrystal polymorphs with a 1:1 M ratio was discovered by cocrystallizing CL-20(2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane)with 1,3-DNP(1,3-dinitropyrazole).These two energetic cocrystal polymorphs(cocrystal 1 and cocrystal 2)exhibit distinct crystal packing styles,which lead to significant variations in their physicochemical properties.Notably,cocrystal 2 has a high density of 1.963 g·cm^(-3)at 170 K,exhibiting high detonation performances(9187 m·s^(-1);38.68 GPa)comparable to HMX(1,3,5,7-tetranitro-1,3,5,7-tetrazocane)meanwhile displaying an improved safety(10 J)relative to RDX(1,3,5-trinitro-1,3,5-triazinane),making it a potential high-energy,low-sensitivity energetic material.This work opens up a new strategy to deeply tune properties of energetic materials by constructing energetic-energetic cocrystal polymorphs.These energetic cocrystal polymorphs represent a new field of energetic materials that has not yet been studied.展开更多
The recent research progress of structure- and size-controlled micro/nano-energetic materials is reviewed, which properties are fundamentally different from those of their corresponding bulk materials. The development...The recent research progress of structure- and size-controlled micro/nano-energetic materials is reviewed, which properties are fundamentally different from those of their corresponding bulk materials. The development of the construction strategies for achieving zero-dimensional (0D), one-dimensional (1D), two-dimensional (2D), and three-dimensional (3D) micro/nanostructures from energetic molecules is introduced. Also, an overview of the unique properties induced by micro/nanostructures and size effects is provided. Special emphasis is focused on the size-dependent properties that are different from those of the conventional micro-sized energetic materials, such as thermal decomposition, sensitivity, combustion and detonation, and compaction behaviors. A conclusion and our view of the future development of micro/nano-energetic materials and devices are given.展开更多
The fracture behavior of polymer-bonded explosive(PBX) seriously affects the safety and reliability of weapon system.The effects of interface debonding and initial meso-damage on the fracture behavior of PBX under qua...The fracture behavior of polymer-bonded explosive(PBX) seriously affects the safety and reliability of weapon system.The effects of interface debonding and initial meso-damage on the fracture behavior of PBX under quasi-static tension are studied using numerical method.A twodimensional representative volume element(RVE) is established based on Voronoi model in which the component contents could be regulated and the particles are randomly distributed.A nonlinear damage model of polymer matrix relative to matrix depth between particles is constructed.The results show that the simulated strain-stress relation is coincident with experiment data.It is found that interface debonding leads to the nucleation and propagation of meso-cracks,and a main crack approximately perpendicular to the loading direction is generated finally.The interface debonding tends to occur in the interface perpendicular to the loading direction.There seems to be a phenomenon that strain softening and hardening alternatively appear around peak stress of stress and strain curve.It is shown that the initial damages of intragranular and interfacial cracks both decrease the modulus and failure stress,and the main crack tends to propagate toward the initial meso-cracks.展开更多
Interaction of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX)/ammonium perchlorate(AP) and its effect on mechanical sensitivity may result in some restrictions for the application of AP/HMX system in high energetic weapo...Interaction of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX)/ammonium perchlorate(AP) and its effect on mechanical sensitivity may result in some restrictions for the application of AP/HMX system in high energetic weapon system. In this work, impact sensitivity test is used to study the effects of wax coating of HMX, AP and aluminum(Al) powder on sensitivity properties of HMX/AP/Al mixtures.Thermogravimetry-differential scanning calorimetry(TG-DSC) analysis has been developed to investigate the mechanism of interaction between HMX and AP during the course of thermal decomposition of HMX/AP/AI mixtures. The results show that severe interaction effect exists between AP and HMX, which causes the impact sensitivity(H_(50)) to become smaller. The impact energy(E_(50)) of mixture can be improved under the circumstances of effective separating HMX from AP by surface coating with Wax. AP may firstly engender low-temperature decomposition under the circumstance of external heat or mechanical impact, which causes the exothermic peak of HMX forward shift about 28 C. The gaseous product releasing from thermal decomposition of HMX accelerates further decomposition of AP. For HMX/AP composite system, the interactive catalysis effect between AP and HMX can be eliminated mostly by adding a great deal of Al powder(i.e. above 30%).展开更多
According to the dimensionless formulae of DOP(depth of penetration) of a rigid projectile into different targets,the resistive force which a target exerts on the projectile during the penetration of rigid projectile ...According to the dimensionless formulae of DOP(depth of penetration) of a rigid projectile into different targets,the resistive force which a target exerts on the projectile during the penetration of rigid projectile is theoretically analyzed.In particular,the threshold V_C of impact velocity applicable for the assumption of constant resistive force is formulated through impulse analysis.The various values of V_C corresponding to different pairs of projectile-target are calculated,and the consistency of the relative test data and numerical results is observed.展开更多
In the present manuscript numerical analysis on the ballistic performance of a tungsten particle/metallic glass matrix(WP/MG) composite rod is conducted by integrating with related experimental investigations. In the ...In the present manuscript numerical analysis on the ballistic performance of a tungsten particle/metallic glass matrix(WP/MG) composite rod is conducted by integrating with related experimental investigations. In the corresponding finite element method(FEM) simulations a modified coupled thermomechanical constitutive model is employed to describe the mechanical properties of metallic glass(MG)matrix, and geometrical models of the WP/MG composite rod are established based on its inner structure. The deformation and failure characteristics of the rod and target materials are analyzed in detail,and the influences of various factors on the ballistic performance of the WP/MG composite long rod are discussed. Related analysis demonstrates that the penetrating performance of the WP/MG rod is similar to that of the tungsten fiber/metallic glass matrix(WF/MG) composite long rod, i.e., a "self-sharpening" behavior also occurs during the penetration process, and correspondingly its penetrating capability is better than that of the tungsten heavy alloy(WHA) rod. However, the mass erosion manner of the WP/MG rod is different and the erosion is relatively severe, thus its penetrating capability is a little lower compared with that of the WF/MG one. Moreover, the impact velocity and the target strength have significant influences on the ballistic performance of the WP/MG composite rod, whereas the effect of initial nose shape is very little.展开更多
In this paper,the gauge points setting is introduced in the SPH simulation to analyze the debris cloud structure generated by the hypervelocity impact of disk projectile on thin plate.Compared with the experiments,mor...In this paper,the gauge points setting is introduced in the SPH simulation to analyze the debris cloud structure generated by the hypervelocity impact of disk projectile on thin plate.Compared with the experiments,more detailed information of the debris cloud structure can be classified from the numerical simulation.However,due to the solitary dispersion and overlap display of the particles in the SPH simulation,accurate comparison between numerical and experimental results is difficult to be performed.To track the velocity and spatial distribution of the particles in the debris cloud induced from disk and plate,gauge points are locally set in the single-layer profile in the SPH model.By analyzing the gauge points’spatial coordinate and velocity,the location and velocity of characteristic points in the debris cloud are determined.The boundary of debris cloud is achieved,as well as the fragments distribution outside the main structure of debris cloud.展开更多
This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） dire...This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） direct sequence spread spectrum （DS-SS） signals with residual carrier. This approach needs some given parameters, such as the period and code rate of PN sequence. The received signal is firstly sampled and divided into non-overlapping signal vectors according to a temporal window, whose duration is two periods of PN sequence. An autocorrelation matrix is then computed and accumulated by those signal vectors one by one. The PN sequence with residual carrier can be estimated by the principal eigenvector of the autocorrelation matrix. Further more, a digital phase lock loop is used to process the estimated PN sequence, it estimates and tracks the residual carrier and removes the residual carrier in the end. Theory analysis and computer simulation results show that this approach can effectively realize the PN sequence blind estimation from the input DS-SS signals with residual carrier in lower SNR.展开更多
The slow wave structure(SWS)of higher-order depressed magnetically insulated transmission line oscillator(HDMILO)is analyzed rigorously,and the electromagnetic field distribution is derived.High-frequency analysis res...The slow wave structure(SWS)of higher-order depressed magnetically insulated transmission line oscillator(HDMILO)is analyzed rigorously,and the electromagnetic field distribution is derived.High-frequency analysis results reveal that the degeneracy of two degenerate HEM!1 modes is removed by the slot in swS plate and the two degenerate modes split into two modes which polarize perpendicularly.Adjusting the azi-muthal position of the slots destroys longitudinal oscillation condition of higher-order modes.展开更多
Shock wave is emitted into the plate and sphere when a sphere hypervelocity impacts onto a thin plate.The fragmentation and phase change of the material caused by the propagation and unloading of shock wave could resu...Shock wave is emitted into the plate and sphere when a sphere hypervelocity impacts onto a thin plate.The fragmentation and phase change of the material caused by the propagation and unloading of shock wave could result in the formation of debris cloud eventually.Propagation models are deduced based on one-dimensional shock wave theory and the geometry of sphere,which uses elliptic equations(corresponding to ellipsoid equations in physical space)to describe the propagation of shock wave and the rarefaction wave.The“Effective thickness”is defined as the critical plate thickness that ensures the rarefaction wave overtake the shock wave at the back of the sphere.The“Effective thickness”is directly related to the form of the debris cloud.The relation of the“Effective thickness”and the“Optimum thickness”is also discussed.The impacts of Al spheres onto Al plates are simulated within SPH to verify the propagation models and associated theories.The results show that the wave fronts predicted by the propagation models are closer to the simulation result at higher impact velocity.The curvatures of the wave fronts decrease with the increase of impact velocities.The predicted“Effective thickness”is consistent with the simulation results.The analysis about the shock wave propagation and unloading in this paper can provide a new sight and inspiration for the quantitative study of hypervelocity impact and space debris protection.展开更多
The integration method of exploding foil initiator system(EFIs) used to be researched to broaden its application range in military and aerospace in the last few decades.In order to lower the firing voltage below 1 kV,...The integration method of exploding foil initiator system(EFIs) used to be researched to broaden its application range in military and aerospace in the last few decades.In order to lower the firing voltage below 1 kV,an integrated EFIs with enhanced energy efficiency was designed.Corresponding exploding foil initiator chips were fabricated in batch via micro electromechanical systems technology by integrating a unified foil,a flyer layer and a barrel on a glass substrate successively,meanwhile its package of the whole system was proposed at a volume of 2.194 cm^(3).The structural parameters were determined by predicted performance including flyer velocity,impact behavior and conduction property via the proposed theoretical models and the static electric field simulation.As expect,this integrated EFIs exhibited excellent functions,which could accelerate the flyer to a terminal velocity over 4 km/s and preeminently initiate HNS-IV pellet at a circuit of 0.24 μF/0.9 kV.Furthermore,the theoretical design,fabrication and performance test have been all included to validate the feasibility of this integrated EFIs that was beneficial for its commercial development in the future.展开更多
基金support from the National Natural Science Foundation of China(Grant No.22175160)the Science Challenge Project(Grant No.TZ2018004)。
文摘5-amino-4-nitrobenzo[1,2-c:3,4-c']bis([1,2,5]oxadiazole)1,6-dioxide(CL-18)exhibits significant potential as an initiating explosive.However,its current synthesis process remains non-scalable due to low yields and safety risks.In this study,we have developed a simple and safe synthetic route for CL-18.It was synthesized from 3,5-dihaloanisole in a four-step reaction with an overall yield exceeding 60%,surpassing all reported yields in the literature.Subsequently,recrystallization of CL-18 was successfully achieved by carefully selecting appropriate solvents and antisolvents to reduce its mechanical sensitivity.Ultimately,when DMF-ethanol was employed as the recrystallization solvent system,satisfactory product yield(>90%)and reduced mechanical sensitivity(IS=15 J;FS=216 N)were obtained.Additionally,CL-18 is derived from the rearrangement of oxygen atoms on i-CL-18 furoxan,and a comparative analysis of their physicochemical properties was conducted.The thermal stability of both compounds is similar,with onset decomposition temperatures recorded at 186 and 182℃respectively.Similarly,they exhibit 5 s breaking point temperatures of 236 and 237℃.Additionally,we present novel insights into the positional-isomerization-laser-ignition performance of CL-18 and its isomer i-CL-18 using laser irradiation for the first time.Remarkably,our findings demonstrate that i-CL-18 exhibits enhanced laser sensitivity,as it can be directly ignited by a 1064 nm wavelength laser,whereas CL-18 lacks this characteristic.
基金supported by the National Natural Science Foundation of China(Gant Nos.11372291 and 11902298)。
文摘Detonation performance is crucial for evaluating the power of high explosives(HEs),and the equation of state(EOS)that accurately describes the high-temperature,high-pressure,and high-temperature,medium-pressure states of detonation products is key to assessing the damage efficiency of these energetic materials.This article examines the limitations of the VLW EOS in representing the thermodynamic states of explosive detonation gas products under high-temperature and medium-to high-pressure conditions.A new gas EOS for detonation products,called VHL(Virial-Han-Long),is proposed.The accuracy of VHL in describing gas states under high-temperature and medium-to high-pressure conditions is verified,and its performance in evaluating explosive detonation and working capabilities is explored.The results demonstrate that VHL exhibits high precision in calculating detonation performance.Subsequently,the detonation performance of three new HEs(ICM-101,ONC,and TNAZ)was calculated and compared to traditional HEs(TATB,CL-20,and HMX).The results indicate that ONC has superior detonation performance compared to the other explosives,while ICM-101 shows a detonation velocity similar to CL-20 but with slightly lower detonation pressure.The detonation characteristics of TNAZ are comparable to those of the standard HE HMX.From the perspective of products,considering the comprehensive work performance(mechanical work and detonation heat),both ONC and ICM-101demonstrate relatively superior performance.
基金supported by the National Natural Science Foundation of China(12402444)。
文摘A new dimensionless number is proposed for dynamic plastic deformation analysis of clamped circular plates under underwater explosion loads by introducing dimensional analysis method to the basic dynamical governing equations of circular plates.The relation between dimensionless final plastic deformation of circular plates and the new dimensionless number is established based on massive underwater explosion test data.Meanwhile,comparative analysis was discussed with two other published dimensionless parameters which indicated the new dimensionless number proposed in this paper is more effective and extensive to predict the dynamic plastic response of circular plates under underwater explosion condition.
基金supported by the National Natural Science Foundation of China(Grant Nos.T2222027 and 12202416)。
文摘The energy release of energetic composites is severely limited by the inert alumina(Al_(2)O_(3))layer on the surface of aluminum(Al).Polytetrafluoroethylene(PTFE)could eliminate Al_(2)O_(3)layer due to its highly electronegativity and oxidability of fluorine.However,adding PTFE particles would weaken interfacial interactions resulted in poor mechanical properties and interfacial exothermic reaction.Herein,a bridging Al-PTFE as fuel and interfacial reinforcing agent was added and used to prepare LLM-105/AlPTFE microspheres,achieving both high energy output and excellent mechanical properties.The energy release and combustion reaction performance of LLM-105/Al-PTFE microspheres are significantly improved due to high reaction heat and increased interfacial reaction area of Al-PTFE.The maximum pressure and pressurization rate of LLM-105/Al-PTFE microspheres are 164.06 kPa and 29.88 kPa/s,respectively,which are 40.11%and 16.67%higher than those of physical mixed samples.Furthermore,the tensile strength and compressive strength of LLM-105/Al-PTFE microspheres are 100.40%and 26.47%higher than those of LLM-105/Al.This work provides a new approach to improve the energy release and mechanical properties for energetic composites.
基金supported by the National Natural Science Foundation of China(Grant Nos.T2222027 and 12202416)。
文摘Aluminum(Al)powder is widely applied in thermobaric explosives due to its high energy density and favorable reaction kinetics.However,the inert oxide layer(Al_(2)O_(3))on Al particles limits combustion reactivity and energy efficiency.Fluoride-based surface modification has been developed as an effective approach to address this issue.Here,four classical fluoropolymers(F11,F14,PVDF,PTFE)are employed as coatings to prepare core-shell Al/Fluoropolymer.The combustion experimental results demonstrate that the core-shell Al/PTFE exhibits the highest flame propagation rate(52.88 mm·ms^(-1))and pressure output(109.02 k Pa)performance.Consequently,core-shell Al/PTFE is selected as a high-energy fuel to prepare RDX/Al/PTFE microspheres via the emulsion and solvent evaporation method,which can enhance the energy performance of RDX.The effects of the core-shell Al/PTFE ratio and RDX content on the combustion heat and pressure output are systematically investigated.The peak pressure reaches a maximum of 187.8 k Pa when the mass ratio of RDX,Al,and PTFE is 60:25:10.Additionally,RDX/Al/PTFE microspheres exhibit significantly higher laser-induced air shock velocities,detonation heat,and detonation pressure than those of pure RDX and RDX/Al.The mechanism underlying the enhanced reactivity and energetic performance is attributed to the ability of PTFE to etch the inert Al_(2)O_(3)shell on the surface of Al particles,thereby improving post-combustion reactions and significantly increasing the overall energy output of RDX explosives.This work offers a novel design strategy for high-energy structural thermobaric explosives for the practical applications.
基金the Presidential Foundation of CAEP(Grant No.YZJJZQ2023005)the National Natural Science Foundation of China(Grant No.22375191).
文摘Nowadays, ultrafine explosives are widely used in military fields. Ultrafine 2,2',4,4',6,6'-hexanitrostilbene(HNS) has emerged as an optimal primer for explosion foil initiators due to its excellent thermal stability and high-voltage short-pulse initiation performance. However, the solid phase ripening of ultrafine HNS leads to a degradation in its impact detonation performance. Previous studies have indicated that residual dimethyl formamide(DMF), which is present in ultrafine HNS prepared using the recrystallization method, affects ultrafine HNS ripening. The mechanism of residual solvent effects on solid phase ripening of ultrafine HNS is unclear. In this work, the specific surface area(SSA) derived from small angle X-ray scattering(SAXS) was utilized for kinetic fitting analysis to explore the mechanism by which residual solvents enhance the solid phase ripening of ultrafine HNS. The results of the SSA measured by insitu SAXS under conditions of 150℃ for 40 h revealed that the sample with 0.2% residual DMF exhibited a 21.51% decrease in SSA, whereas the sample with only 0.04% residual DMF showed a decrease of 15.66%.Furthermore, the higher amounts of residual DMF accelerated the reduction in SSA with time. Kinetic fitting analysis demonstrated that reducing residual DMF would lower both the activation energy and the pre-exponential factor, consequently decreasing the rate constant of solid phase ripening. The mechanism was speculated that it primarily facilitated the Ostwald ripening(OR). Additionally, contrast variation small angle X-ray scattering(CV-SAXS) confirmed that coating of ultrafine HNS particles is an effective method for inhibiting ripening, significantly reducing both the rate and extent of ripening of ultrafine HNS. This study predicts how residual solvents impact the solid phase ripening process of ultrafine HNS and proposes strategies for enhancing the long-term stability of ultrafine explosives.
基金support provided by the National Natural Science Foundation of China(Grant No.12102405)the Presidential Foundation of CAEP(Grant No.YZJJZQ2023008).
文摘This study investigates the paradoxical detonation behavior of TKX-50,a nitrogen-rich energetic material,exhibiting higher detonation velocities but lower metal acceleration ability compared to HMX.Through experimental measurements and theoretical calculations,we propose a novel three-factor competition mechanism to explain this phenomenon.TKX-50-based PBX formulations achieved detonation velocities up to 9100 m/s,surpassing HMX-based counterparts.However,cylinder expansion tests revealed a 15%reduction in metal acceleration ability.Thermochemical measurements showed lower detonation heat for TKX-50(4900 J/g)versus HMX(5645 J/g).Our mechanism involves:(1)compositional effects prevailing at high pressures;(2)Energy release becoming essential as pressure drops;(3)Pressure-dependent product composition evolution functioning at low pressure.VLW code calculations unveiled a"crossover"in Hugoniot curves,lending support to this mechanism.This study furnishes a new framework for comprehending the performance of nitrogen-rich energetic materials,with significant implications for the design and optimization of future high-energy density materials.
基金supported by the National Natural Science Foundation of China (Grant Nos. 22475179 and 22275173)。
文摘Realizing effective enhancement in the thermally conductive performance of polymer bonded explosives(PBXs) is vital for improving the resultant environmental adaptabilities of the PBXs composites. Herein, a kind of primary-secondary thermally conductive network was designed by water-suspension granulation, surface coating, and hot-pressing procedures in the graphene-based PBXs composites to greatly increase the thermal conductive performance of the composites. The primary network with a threedimensional structure provided the heat-conducting skeleton, while the secondary network in the polymer matrix bridged the primary network to increase the network density. The enhancement efficiency in the thermally conductive performance of the composites reached the highest value of 59.70% at a primary-secondary network ratio of 3:1. Finite element analysis confirmed the synergistic enhancement effect of the primary and secondary thermally conductive networks. This study introduces an innovative approach to designing network structures for PBX composites, significantly enhancing their thermal conductivity.
基金support for this study by the National Natural Science Foundation of China(Grant No.22275175)。
文摘Herein,a first example of energetic-energetic cocrystal polymorphs with a 1:1 M ratio was discovered by cocrystallizing CL-20(2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane)with 1,3-DNP(1,3-dinitropyrazole).These two energetic cocrystal polymorphs(cocrystal 1 and cocrystal 2)exhibit distinct crystal packing styles,which lead to significant variations in their physicochemical properties.Notably,cocrystal 2 has a high density of 1.963 g·cm^(-3)at 170 K,exhibiting high detonation performances(9187 m·s^(-1);38.68 GPa)comparable to HMX(1,3,5,7-tetranitro-1,3,5,7-tetrazocane)meanwhile displaying an improved safety(10 J)relative to RDX(1,3,5-trinitro-1,3,5-triazinane),making it a potential high-energy,low-sensitivity energetic material.This work opens up a new strategy to deeply tune properties of energetic materials by constructing energetic-energetic cocrystal polymorphs.These energetic cocrystal polymorphs represent a new field of energetic materials that has not yet been studied.
基金Sponsored by National Natural Science Foundation of China (21231002,21276026,21271023,21173021,91022006,11202193,11172276,and 11072225)the 111 Project ( B07012)+1 种基金the Program of Cooperation of the Beijing Education Commission ( 20091739006)Specialized Research Fund for the Doctoral Program of Higher Education ( 20101101110031)
文摘The recent research progress of structure- and size-controlled micro/nano-energetic materials is reviewed, which properties are fundamentally different from those of their corresponding bulk materials. The development of the construction strategies for achieving zero-dimensional (0D), one-dimensional (1D), two-dimensional (2D), and three-dimensional (3D) micro/nanostructures from energetic molecules is introduced. Also, an overview of the unique properties induced by micro/nanostructures and size effects is provided. Special emphasis is focused on the size-dependent properties that are different from those of the conventional micro-sized energetic materials, such as thermal decomposition, sensitivity, combustion and detonation, and compaction behaviors. A conclusion and our view of the future development of micro/nano-energetic materials and devices are given.
文摘The fracture behavior of polymer-bonded explosive(PBX) seriously affects the safety and reliability of weapon system.The effects of interface debonding and initial meso-damage on the fracture behavior of PBX under quasi-static tension are studied using numerical method.A twodimensional representative volume element(RVE) is established based on Voronoi model in which the component contents could be regulated and the particles are randomly distributed.A nonlinear damage model of polymer matrix relative to matrix depth between particles is constructed.The results show that the simulated strain-stress relation is coincident with experiment data.It is found that interface debonding leads to the nucleation and propagation of meso-cracks,and a main crack approximately perpendicular to the loading direction is generated finally.The interface debonding tends to occur in the interface perpendicular to the loading direction.There seems to be a phenomenon that strain softening and hardening alternatively appear around peak stress of stress and strain curve.It is shown that the initial damages of intragranular and interfacial cracks both decrease the modulus and failure stress,and the main crack tends to propagate toward the initial meso-cracks.
基金supported by the National Nature Science Foundation of China(Nos.11402238,11502243 and 11502245)
文摘Interaction of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX)/ammonium perchlorate(AP) and its effect on mechanical sensitivity may result in some restrictions for the application of AP/HMX system in high energetic weapon system. In this work, impact sensitivity test is used to study the effects of wax coating of HMX, AP and aluminum(Al) powder on sensitivity properties of HMX/AP/Al mixtures.Thermogravimetry-differential scanning calorimetry(TG-DSC) analysis has been developed to investigate the mechanism of interaction between HMX and AP during the course of thermal decomposition of HMX/AP/AI mixtures. The results show that severe interaction effect exists between AP and HMX, which causes the impact sensitivity(H_(50)) to become smaller. The impact energy(E_(50)) of mixture can be improved under the circumstances of effective separating HMX from AP by surface coating with Wax. AP may firstly engender low-temperature decomposition under the circumstance of external heat or mechanical impact, which causes the exothermic peak of HMX forward shift about 28 C. The gaseous product releasing from thermal decomposition of HMX accelerates further decomposition of AP. For HMX/AP composite system, the interactive catalysis effect between AP and HMX can be eliminated mostly by adding a great deal of Al powder(i.e. above 30%).
基金supported by the National Natural Science Foundation of China(1127105011371183+2 种基金61403036)the Science and Technology Development Foundation of CAEP(2013A04030202013B0403068)
基金supported by the National Outstanding Young Scientist Foundation of China(11225213)Major Program of National Natural Science Foundation of China(Grant No.11390362)
文摘According to the dimensionless formulae of DOP(depth of penetration) of a rigid projectile into different targets,the resistive force which a target exerts on the projectile during the penetration of rigid projectile is theoretically analyzed.In particular,the threshold V_C of impact velocity applicable for the assumption of constant resistive force is formulated through impulse analysis.The various values of V_C corresponding to different pairs of projectile-target are calculated,and the consistency of the relative test data and numerical results is observed.
基金supported by the Science and Technology Development Fund (2015B0201025)the key subject "Computational Solid Mechanics" of China Academy of Engineering Physics+1 种基金the National Outstanding Young Scientists Foundation of China (11225213)the National Natural Science Foundation of China (11521062,11602258)
文摘In the present manuscript numerical analysis on the ballistic performance of a tungsten particle/metallic glass matrix(WP/MG) composite rod is conducted by integrating with related experimental investigations. In the corresponding finite element method(FEM) simulations a modified coupled thermomechanical constitutive model is employed to describe the mechanical properties of metallic glass(MG)matrix, and geometrical models of the WP/MG composite rod are established based on its inner structure. The deformation and failure characteristics of the rod and target materials are analyzed in detail,and the influences of various factors on the ballistic performance of the WP/MG composite long rod are discussed. Related analysis demonstrates that the penetrating performance of the WP/MG rod is similar to that of the tungsten fiber/metallic glass matrix(WF/MG) composite long rod, i.e., a "self-sharpening" behavior also occurs during the penetration process, and correspondingly its penetrating capability is better than that of the tungsten heavy alloy(WHA) rod. However, the mass erosion manner of the WP/MG rod is different and the erosion is relatively severe, thus its penetrating capability is a little lower compared with that of the WF/MG one. Moreover, the impact velocity and the target strength have significant influences on the ballistic performance of the WP/MG composite rod, whereas the effect of initial nose shape is very little.
基金supported by the Natural Science Foundations of China(11872118,11627901)。
文摘In this paper,the gauge points setting is introduced in the SPH simulation to analyze the debris cloud structure generated by the hypervelocity impact of disk projectile on thin plate.Compared with the experiments,more detailed information of the debris cloud structure can be classified from the numerical simulation.However,due to the solitary dispersion and overlap display of the particles in the SPH simulation,accurate comparison between numerical and experimental results is difficult to be performed.To track the velocity and spatial distribution of the particles in the debris cloud induced from disk and plate,gauge points are locally set in the single-layer profile in the SPH model.By analyzing the gauge points’spatial coordinate and velocity,the location and velocity of characteristic points in the debris cloud are determined.The boundary of debris cloud is achieved,as well as the fragments distribution outside the main structure of debris cloud.
基金supported by the National Natural Science Foundation of China (10776040 60602057)+4 种基金Program for New Century Excellent Talents in University (NCET)the Project of Key Laboratory of Signal and Information Processing of Chongqing (CSTC2009CA2003)the Natural Science Foundation of Chongqing Science and Technology Commission (CSTC2009BB2287)the Natural Science Foundation of Chongqing Municipal Education Commission (KJ060509 KJ080517)
文摘This paper presents an approach of singular value de- composition plus digital phase lock loop to solve the difficult problem of blind pseudo-noise （PN） sequence estimation in low signal to noise ratios （SNR） direct sequence spread spectrum （DS-SS） signals with residual carrier. This approach needs some given parameters, such as the period and code rate of PN sequence. The received signal is firstly sampled and divided into non-overlapping signal vectors according to a temporal window, whose duration is two periods of PN sequence. An autocorrelation matrix is then computed and accumulated by those signal vectors one by one. The PN sequence with residual carrier can be estimated by the principal eigenvector of the autocorrelation matrix. Further more, a digital phase lock loop is used to process the estimated PN sequence, it estimates and tracks the residual carrier and removes the residual carrier in the end. Theory analysis and computer simulation results show that this approach can effectively realize the PN sequence blind estimation from the input DS-SS signals with residual carrier in lower SNR.
文摘The slow wave structure(SWS)of higher-order depressed magnetically insulated transmission line oscillator(HDMILO)is analyzed rigorously,and the electromagnetic field distribution is derived.High-frequency analysis results reveal that the degeneracy of two degenerate HEM!1 modes is removed by the slot in swS plate and the two degenerate modes split into two modes which polarize perpendicularly.Adjusting the azi-muthal position of the slots destroys longitudinal oscillation condition of higher-order modes.
基金supported by the National Natural Science Foundation of China(11627901,11872118).
文摘Shock wave is emitted into the plate and sphere when a sphere hypervelocity impacts onto a thin plate.The fragmentation and phase change of the material caused by the propagation and unloading of shock wave could result in the formation of debris cloud eventually.Propagation models are deduced based on one-dimensional shock wave theory and the geometry of sphere,which uses elliptic equations(corresponding to ellipsoid equations in physical space)to describe the propagation of shock wave and the rarefaction wave.The“Effective thickness”is defined as the critical plate thickness that ensures the rarefaction wave overtake the shock wave at the back of the sphere.The“Effective thickness”is directly related to the form of the debris cloud.The relation of the“Effective thickness”and the“Optimum thickness”is also discussed.The impacts of Al spheres onto Al plates are simulated within SPH to verify the propagation models and associated theories.The results show that the wave fronts predicted by the propagation models are closer to the simulation result at higher impact velocity.The curvatures of the wave fronts decrease with the increase of impact velocities.The predicted“Effective thickness”is consistent with the simulation results.The analysis about the shock wave propagation and unloading in this paper can provide a new sight and inspiration for the quantitative study of hypervelocity impact and space debris protection.
基金National Natural Science Foundation of China (Grant No.11872013) to provide fund for conducting experiments。
文摘The integration method of exploding foil initiator system(EFIs) used to be researched to broaden its application range in military and aerospace in the last few decades.In order to lower the firing voltage below 1 kV,an integrated EFIs with enhanced energy efficiency was designed.Corresponding exploding foil initiator chips were fabricated in batch via micro electromechanical systems technology by integrating a unified foil,a flyer layer and a barrel on a glass substrate successively,meanwhile its package of the whole system was proposed at a volume of 2.194 cm^(3).The structural parameters were determined by predicted performance including flyer velocity,impact behavior and conduction property via the proposed theoretical models and the static electric field simulation.As expect,this integrated EFIs exhibited excellent functions,which could accelerate the flyer to a terminal velocity over 4 km/s and preeminently initiate HNS-IV pellet at a circuit of 0.24 μF/0.9 kV.Furthermore,the theoretical design,fabrication and performance test have been all included to validate the feasibility of this integrated EFIs that was beneficial for its commercial development in the future.
