期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
考虑变形历程的热处理工艺对Ti-6Al-4V合金组织和性能影响的研究
1
作者 李硕 谢碧君 +5 位作者 郭逸丰 郑莉莉 李希超 徐斌 孙明月 李殿中 《热加工工艺》 北大核心 2025年第10期49-55,共7页
航空用大型钛合金环形件截面复杂且尺寸极大,在轧制成形及热处理过程中,由于不同部位的变形和传热条件不同,将导致环件横截面不同区域应变和温度分布的不均匀性,进而使得环件不同区域微观组织和力学性能存在差异性,这种不均匀状态极大... 航空用大型钛合金环形件截面复杂且尺寸极大,在轧制成形及热处理过程中,由于不同部位的变形和传热条件不同,将导致环件横截面不同区域应变和温度分布的不均匀性,进而使得环件不同区域微观组织和力学性能存在差异性,这种不均匀状态极大地影响大型钛合金环件的整体力学性能。根据大型环件不同区域的应变分布设计不同变形量的压缩实验并实施不同的热处理工艺,研究不同变形量及退火工艺对Ti-6Al-4V合金组织及其力学性能的影响。结果表明,变形量对α_(p)和β_(t)相的尺寸、含量和形貌具有显著影响。随着变形量的增大,动态再结晶发生,α_(p)和β_(t)相的晶粒尺寸先逐渐减小再增大,α相的相对含量则呈现先逐渐升高后减小的趋势。组织变化使得变形态Ti-6Al-4V合金的抗拉强度呈现先升高后降低的趋势。而经退火处理后,α_(p)和β_(t)相的尺寸、含量和形貌保持与变形态试样一致的变化规律,且退火态TC4合金的抗拉强度及伸长率均呈现先升高后降低的情况,组织和性能均表现出一定的遗传性。 展开更多
关键词 TI-6AL-4V合金 变形遗传 退火 微观组织 拉伸强度
在线阅读 下载PDF
The use of a ternary metal sulfide loading on carbon fibers as the sulfur host for high performance low-temperature lithium sulfur batteries
2
作者 HE Xin ZUO Huai-yang +4 位作者 XIAO Ru QU Zhuo-yan SUN Zhen-hua WANG Bao Li Feng 《新型炭材料(中英文)》 北大核心 2025年第1期167-177,共11页
The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nit... The use of lithium-sulfur(Li-S)batteries is limited by sulfur redox reactions involving multi-phase transformations,especially at low-temperatures.To address this issue,we report a material(FCNS@NCFs)consisting of nitrogen-doped carbon fibers loaded with a ternary metal sulf-ide((Fe,Co,Ni)_(9)S_(8))for use as the sulfur host in Li-S batteries.This materi-al was prepared using transfer blot filter paper as the carbon precursor,thiourea as the source of nitrogen and sulfur,and FeCl_(3)·6H_(2)O,CoCl_(2)·6H_(2)O and NiCl_(2)·6H_(2)O as the metal ion sources.It was synthesized by an impreg-nation method followed by calcination.The nitrogen doping significantly in-creased the conductivity of the host,and the metal sulfides have excellent catalytic activities.Theoretical calculations,and adsorption and deposition experiments show that active sites on the surface of FCNS@NCFs selectively adsorb polysulfides,facilitate rapid adsorption and conversion,prevent cathode passivation and inhib-it the polysulfide shuttling.The FCNS@NCFs used as the sulfur host has excellent electrochemical properties.Its initial dis-charge capacity is 1639.0 mAh g^(−1) at 0.2 C and room temperature,and it remains a capacity of 1255.1 mAh g^(−1) after 100 cycles.At−20~C,it has an initial discharge capacity of 1578.5 mAh g^(−1) at 0.2 C,with a capacity of 867.5 mAh g^(−1) after 100 cycles.Its excellent performance at both ambient and low temperatures suggests a new way to produce high-performance low-temper-ature Li-S batteries. 展开更多
关键词 Lithium sulfur batteries Low temperature Transition metal sulfides Sulfur conversion kinetics
在线阅读 下载PDF
盾构机主轴承套圈表面淬火工艺 被引量:1
3
作者 封少波 吴长江 +2 位作者 袁麟 胡小强 李殿中 《轴承》 北大核心 2024年第11期121-127,共7页
盾构机主轴承服役时需承受交变重载等恶劣工况,其套圈滚道表淬层要求具有足够的深度,较高的强度和硬度以及良好的抗疲劳和耐磨损等性能;但淬硬层过深易导致显微组织粗大,淬火残余应力高,甚至出现淬火裂纹等问题。为实现套圈滚道表淬层... 盾构机主轴承服役时需承受交变重载等恶劣工况,其套圈滚道表淬层要求具有足够的深度,较高的强度和硬度以及良好的抗疲劳和耐磨损等性能;但淬硬层过深易导致显微组织粗大,淬火残余应力高,甚至出现淬火裂纹等问题。为实现套圈滚道表淬层深度与性能调控,分析了冷却方式、加热温度和时间、低温回火温度对42CrMo4M钢淬硬层的深度、硬度、显微组织和残余应力的影响,结果表明:水淬的淬硬层硬度和深度高于油冷和喷水;加热温度为870~920℃,加热时间为20~60 s,水淬时的淬硬层深度均达到14 mm以上,表层硬度不小于54 HRC,其中加热温度为900℃,加热时间为40~60 s时的淬硬层深度最大,硬度最均匀;低温回火温度在150~300℃时,随着回火温度升高,淬硬层硬度下降,残余应力减小,基体逐渐析出碳化物。最佳表面淬火工艺为加热温度900℃、加热时间40 s、水淬冷却,低温回火温度不大于210℃,采用该工艺完成了Φ7.6 m主轴承套圈工程样件滚道的表面淬火,套圈滚道表面淬硬层深度为10.5 mm,表面硬度不小于55 HRC,淬硬层组织主要为板条马氏体。 展开更多
关键词 滚动轴承 盾构机轴承 热处理 感应淬火 低温回火 硬度 残余应力
在线阅读 下载PDF
上一页 1 下一页 到第
使用帮助 返回顶部