The process of ground vehicle dynamic gravimetry is inevitably affected by the carrier’s maneuvering acceleration,which makes the result contain a large amount of dynamic error.In this paper,we propose a dynamic erro...The process of ground vehicle dynamic gravimetry is inevitably affected by the carrier’s maneuvering acceleration,which makes the result contain a large amount of dynamic error.In this paper,we propose a dynamic error suppression method of gravimetry based on the high-precision acquisition of external velocity for compensating the horizontal error of the inertial plat-form.On the basis of platform gravity measurement,firstly,the dynamic performance of the system is enhanced by optimizing the horizontal damping network of the inertial platform and selecting its parameter.Secondly,an improved federal Kalman filtering algorithm and a fault diagnosis method are designed using strapdown inertial navigation system(SINS),odometer(OD),and laser Doppler velocimeter(LDV).Simulation validates that these methods can improve the accuracy and robustness of the external velocity acquisition.Three survey lines are selected in Tianjin,China,for the gravimetry experiments with different maneuvering levels,and the results demonstrate that after dynamic error suppression,the internal coincidence accuracies of smooth and uniform operation,obvious acceleration and deceleration operation,and high-dynamic operation are improved by 70.2%,73.6%,and 77.9%to reach 0.81 mGal,1.30 mGal,and 1.94 mGal,respectively,and the external coinci-dence accuracies during smooth and uniform operation are improved by 48.6%up to 1.66 mGal.It is shown that the pro-posed method can effectively suppress the dynamic error,and that the accuracy improvement increases with carrier maneuver-ability.However,the amount of residual error that can not be entirely eliminated increases as well,so the ground vehicle dynamic gravimetry should be maintained in the carrier for smooth and uniform operation.展开更多
To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design...To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design problem can be solved using QFT but it fails to guarantee a high precision tracking. This problem is solved by a robust digital QFT control scheme based on zero phase error （ZPE） feed forward compensation. This scheme consists of two parts： a QFT controller in the closed-loop system and a ZPE feed-forward compensator. Digital QFT controller is designed to overcome the uncertainties in the system. Digital ZPE feed forward controller is used to improve the tracking precision. Simulation and real-time examples for flight simulator servo system indicate that this control scheme can guarantee both high robust performance and high position tracking precision.展开更多
The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of ...The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of the thermal error modeling for machine tools, a new approach of regression orthogonal design is proposed, which combines the statistic theory with machine structures, surrounding condition, engineering judgements, and experience in modeling. A whole computation and analysis procedure is given. Therefore, the model got from this method are more robust and practical than those got from the present method that depends on the modeling data completely. At last more than 100 applications of CNC turning center with only one thermal error model are given. The cutting diameter variation reduces from more than 35 μm to about 12 μm with the orthogonal regression modeling and compensation of thermal error.展开更多
On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point a...On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point are established according to the three usual methods of mounting workpieces on a turning machine. Further a prediction system for diameter errors is developed; a new method, called discrete nodes output, is presented and applied to expressing workpiece diameter errors at given points along the part axis, then off-line compensation is implemented according to the prediction values to diminish machining errors. The results indicate that the method can diminish diameter errors more than 70%, greatly improve the machining accuracy of bars.展开更多
In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error m...In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error model for the laser annealing table was established. It supports the identification of 7 geometric errors affecting the annealing accuracy. An original identification method was presented to recognize these geometric errors. Positioning errors of 5 lines in the workspace were measured by a laser interferometer, and the 7 geometric errors were identified by the proposed algorithm. Finally, a software-based error compensation method was adopted, and a compensation mechanism was developed in a postprocessor based on LabVIEW. The identified geometric errors can be compensated by converting ideal NC codes to actual NC codes. A validation experiment has been conducted on the laser annealing table, and the results indicate that positioning errors of two validation lines decreased from ±37 μm and ±33 μm to ±5 μm and ±4.5 μm, respectively. The geometric error modeling, identification and compensation method presented in this work can be straightforwardly extended to any configurations of 2-dimensional worktable.展开更多
According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accur...According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.展开更多
Rotationally symmetric triangulation(RST)sensor has more flexibility and less uncertainty limits because of the abaxial rotationally symmetric optical system.But if the incident laser is eccentric,the symmetry of the ...Rotationally symmetric triangulation(RST)sensor has more flexibility and less uncertainty limits because of the abaxial rotationally symmetric optical system.But if the incident laser is eccentric,the symmetry of the image will descend,and it will result in the eccentric error especially when some part of the imaged ring is blocked.The model of rotationally symmetric triangulation that meets the Schimpflug condition is presented in this paper.The error from eccentric incident laser is analysed.It is pointed out that the eccentric error is composed of two parts,one is a cosine in circumference and proportional to the eccentric departure factor,and the other is a much smaller quadric factor of the departure.When the ring is complete,the first error factor is zero because it is integrated in whole ring, but if some part of the ring is blocked,the first factor will be the main error.Simulation verifies the result of the a- nalysis.At last,a compensation method to the error when some part of the ring is lost is presented based on neural network.The results of experiment show that the compensation will make the absolute maximum error descend to half,and the standard deviation of error descends to 1/3.展开更多
The frictional properties of micro bearings have strong influence on the performance of the whole system because of tiny scale of micro-electromechanical system (MEMS). To develop micro bearings with low friction,it i...The frictional properties of micro bearings have strong influence on the performance of the whole system because of tiny scale of micro-electromechanical system (MEMS). To develop micro bearings with low friction,it is important to evaluate the friction behaviors on the micro bearing. The testing system and the principle to evaluate the tribological performance of micromachining work-pieces under the load of mill Newton scale is introduced in paper "A new approach to measure the friction coefficient of micro journal bearings" of Yao et al,. But as the tribological force is faint in micro scale, the measured force is influenced a lot by the testing error. As the equation of that of Yao’s paper is very sensitive to the measured force, the tested result is influenced remarkably by testing error. So it is hard to get precision result. To solve this problem, the test system with new compensation method is introduced to precisely evaluate tribological performance under mill scale. The new metrology method is developed by means of the error compensation from two sets of testing data. The data are the force collected respectively when the friction counterparts rotate in CW(clockwise) and CCW(counter-clockwise) direction. So we deduce the equation of friction coefficient respctively on the condition of journal running in CCW and CW direction. As condition of measuring those two friciton coefficients are alike except the running direction of journal, and then the friction coefficient should be the same because this difference of direction has no influence on the fricition coefficients. Considering this, we unite the both equation, make the data measured in different subtract each other in the equation, and then a new equation can be gotten. This new equation enhances the metrology precision of friction coefficient theoretically thanks to the counteracting of error values in the equation. Using this method we testing the friction of high speed steel journal with hard alloy bearing. The result shows the new compensation method has better precision and repetition than CW and CCW method thanks to the error resistance.展开更多
Some methods which use an optical tracker(OT) as a standard reference of electromagnetic tracker(EMT) were proposed in order to compensate the output error of electromagnetic tracker. Usually,they use a magneto-optic ...Some methods which use an optical tracker(OT) as a standard reference of electromagnetic tracker(EMT) were proposed in order to compensate the output error of electromagnetic tracker. Usually,they use a magneto-optic tool to collect the outputs of OT and EMT simultaneously,and then compare the output of OT with that of EMT to compensate the error of EMT. Although the outputs of EMT and OT can be matched each other by using a time stamp which denotes when the acquirement command is sent,but the accuracy will decrease if the tool moves faster for the errors of the time stamp itself. A rapid method for compensating EMT output error is proposed. A particular scan mode of the magneto-optic tool is designed for collecting EMT and OT outputs,and a data registration method is proposed to match the outputs of EMT and OT. The simulated results show that the output error of EMT can be decreased efficiently and the accuracy of the compensation can be improved by about 15% compared with that of the existing methods.展开更多
To analyze the influence of time synchronization error,phase synchronization error,frequency synchronization error,internal delay of the transceiver system,and range error and angle error between the unit radars on th...To analyze the influence of time synchronization error,phase synchronization error,frequency synchronization error,internal delay of the transceiver system,and range error and angle error between the unit radars on the target detection performance,firstly,a spatial detection model of distributed high-frequency surface wave radar(distributed-HFSWR)is established in this paper.In this model,a method for accurate extraction of direct wave spectrum based on curve fitting is proposed to obtain accurate system internal delay and frequency synchronization error under complex electromagnetic environment background and low signal to noise ratio(SNR),and to compensate for the shift of range and Doppler frequency caused by time-frequency synchronization error.The direct wave component is extracted from the spectrum,the range estimation error and Doppler estimation error are reduced by the method of curve fitting,and the fitting accuracy of the parameters is improved.Then,the influence of frequency synchronization error on target range and radial Doppler velocity is quantitatively analyzed.The relationship between frequency synchronization error and radial Doppler velocity shift and range shift is given.Finally,the system synchronization parameters of the trial distributed-HFSWR are obtained by the proposed spectrum extraction method based on curve fitting,the experimental data is compensated to correct the shift of the target,and finally the correct target parameter information is obtained.Simulations and experimental results demonstrate the superiority and correctness of the proposed method,theoretical derivation and detection model proposed in this paper.展开更多
In the field of deep space exploration,the rapid development of terahertz spectrometer has put forward higher requirements to the back-end chirp transform spectrometer(CTS)system.In order to simultaneously meet the me...In the field of deep space exploration,the rapid development of terahertz spectrometer has put forward higher requirements to the back-end chirp transform spectrometer(CTS)system.In order to simultaneously meet the measurement requirements of wide bandwidth and high accuracy spectral lines,we built a CTS system with an analysis bandwidth of 1 GHz and a frequency resolution of 100 kHz around the surface acoustic wave(SAW)chirp filter with a bandwidth of 1 GHz.In this paper,the relationship between the CTS nonlinear phase error shift model and the basic measurement parameters is studied,and the effect of CTS phase mismatch on the pulse compression waveform is analyzed by simulation.And the expander error optimization method is proposed for the problem that the large nonlinear error of the expander leads to the unbalanced response of the CTS system and the serious distortion of the compressed pulse waveform under large bandwidth.It is verified through simulation and experiment that the method is effective for reducing the root mean square error(RMSE)of the phase of the expander from 18.75°to 6.65°,reducing the in-band standard deviation of the CTS frequency resolution index from 8.43 kHz to 4.72 kHz,solving the problem of serious distortion of the compressed pulse waveform,and improving the uneven CTS response under large bandwidth.展开更多
摆线泵转子的齿廓形状和加工精度决定了齿轮泵容腔的密封性,进而影响吸油和压油等运动特性。然而,转子的齿廓形状多是企业根据自身实际需求自行设计的,这就造成齿廓误差测量过程中的测量基准和设计基准不一致,测量结果更无法准确反映转...摆线泵转子的齿廓形状和加工精度决定了齿轮泵容腔的密封性,进而影响吸油和压油等运动特性。然而,转子的齿廓形状多是企业根据自身实际需求自行设计的,这就造成齿廓误差测量过程中的测量基准和设计基准不一致,测量结果更无法准确反映转子的齿廓加工质量。鉴于此,将企业设计的产品模型数据交互规范(Standard for the Exchange of Product model data, STEP)齿廓作为测量所必需的基准数据,在使用一维测头的国产齿轮测量中心上完成了转子齿廓的快速检测,采用重构及匹配等补偿处理方法,实现了摆线泵转子误差的精确评定。结果表明,该方法具有较好的柔性,对于复杂齿面的精确测量和评定具有重要的理论意义。展开更多
A grating lobes suppression method for chirp-subpulse stepped frequency（CSSF） signals is proposed, which is applied to deformation monitoring using the ground based synthetic aperture radar（GB-SAR） system. This me...A grating lobes suppression method for chirp-subpulse stepped frequency（CSSF） signals is proposed, which is applied to deformation monitoring using the ground based synthetic aperture radar（GB-SAR） system. This method is based on accurate estimation and correction of the phase and amplitude error along two dimensions（range and azimuth）, i.e., the error estimation inside the subpulse（in-subpulse error） and across the stepped frequency subpulses（cross-subpulse error） of transmitted CSSF signals. Validated both with simulated data and experimental data recorded in the deformation monitoring campaign, it can be seen that the method as well as the relative conclusions can be fully and effectively applied to most of the stepped frequency systems.展开更多
In recent years, ground-based micro-deformation monitoring radar has attracted much attention due to its excellent monitoring capability. By controlling the repeated campaigns of the radar antenna on a fixed track, gr...In recent years, ground-based micro-deformation monitoring radar has attracted much attention due to its excellent monitoring capability. By controlling the repeated campaigns of the radar antenna on a fixed track, ground-based micro-deformation monitoring radar can accomplish repeat-pass interferometry without a space baseline and thus obtain highprecision deformation data of a large scene at one time. However, it is difficult to guarantee absolute stable installation position in every campaign. If the installation position is unstable, the stability of the radar track will be affected randomly, resulting in time-varying baseline error. In this study, a correction method for this error is developed by analyzing the error distribution law while the spatial baseline is unknown. In practice, the error data are first identified by frequency components, then the data of each one-dimensional array(in azimuth direction or range direction) are grouped based on numerical distribution period, and finally the error is corrected by the nonlinear model established with each group.This method is verified with measured data from a slope in southern China, and the results show that the method can effectively correct the time-varying baseline error caused by rail instability and effectively improve the monitoring data accuracy of groundbased micro-deformation radar in short term and long term.展开更多
In order to improve the video quality of transmission with data loss,a spatial and temporal error concealment method was proposed,which considered both the state information of the network and the perceptual weight of...In order to improve the video quality of transmission with data loss,a spatial and temporal error concealment method was proposed,which considered both the state information of the network and the perceptual weight of the video content.The proposed method dynamically changed the reliability weight of the neighboring macroblock,which was used to conceal the lost macroblocks according to the packet loss rate of the current channel state.The perceptual weight map was utilized as side information to do weighted pixel interpolation and side-match based motion compensation for spatial and temporal error concealment,respectively.And the perceptual weight of the neighboring macroblocks was adaptively modified according to the perceptual weight of the lost macroblocks.Compared with the method used in H.264 joint model,experiment results show that the proposed method performs well both in subjective video quality and objective video quality,and increases the average peak signal-to-noise ratio(PSNR) of the whole frame by about 0.4 dB when the video bitstreams are transmitted with packets loss.展开更多
基金supported by the Shanxi Provincial Natural Science Basic Research Program Young Talent Project(S2019-JC-QN-2408).
文摘The process of ground vehicle dynamic gravimetry is inevitably affected by the carrier’s maneuvering acceleration,which makes the result contain a large amount of dynamic error.In this paper,we propose a dynamic error suppression method of gravimetry based on the high-precision acquisition of external velocity for compensating the horizontal error of the inertial plat-form.On the basis of platform gravity measurement,firstly,the dynamic performance of the system is enhanced by optimizing the horizontal damping network of the inertial platform and selecting its parameter.Secondly,an improved federal Kalman filtering algorithm and a fault diagnosis method are designed using strapdown inertial navigation system(SINS),odometer(OD),and laser Doppler velocimeter(LDV).Simulation validates that these methods can improve the accuracy and robustness of the external velocity acquisition.Three survey lines are selected in Tianjin,China,for the gravimetry experiments with different maneuvering levels,and the results demonstrate that after dynamic error suppression,the internal coincidence accuracies of smooth and uniform operation,obvious acceleration and deceleration operation,and high-dynamic operation are improved by 70.2%,73.6%,and 77.9%to reach 0.81 mGal,1.30 mGal,and 1.94 mGal,respectively,and the external coinci-dence accuracies during smooth and uniform operation are improved by 48.6%up to 1.66 mGal.It is shown that the pro-posed method can effectively suppress the dynamic error,and that the accuracy improvement increases with carrier maneuver-ability.However,the amount of residual error that can not be entirely eliminated increases as well,so the ground vehicle dynamic gravimetry should be maintained in the carrier for smooth and uniform operation.
基金This project was supported by the Aeronautics Foundation of China (00E51022).
文摘To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design problem can be solved using QFT but it fails to guarantee a high precision tracking. This problem is solved by a robust digital QFT control scheme based on zero phase error （ZPE） feed forward compensation. This scheme consists of two parts： a QFT controller in the closed-loop system and a ZPE feed-forward compensator. Digital QFT controller is designed to overcome the uncertainties in the system. Digital ZPE feed forward controller is used to improve the tracking precision. Simulation and real-time examples for flight simulator servo system indicate that this control scheme can guarantee both high robust performance and high position tracking precision.
文摘The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of the thermal error modeling for machine tools, a new approach of regression orthogonal design is proposed, which combines the statistic theory with machine structures, surrounding condition, engineering judgements, and experience in modeling. A whole computation and analysis procedure is given. Therefore, the model got from this method are more robust and practical than those got from the present method that depends on the modeling data completely. At last more than 100 applications of CNC turning center with only one thermal error model are given. The cutting diameter variation reduces from more than 35 μm to about 12 μm with the orthogonal regression modeling and compensation of thermal error.
文摘On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point are established according to the three usual methods of mounting workpieces on a turning machine. Further a prediction system for diameter errors is developed; a new method, called discrete nodes output, is presented and applied to expressing workpiece diameter errors at given points along the part axis, then off-line compensation is implemented according to the prediction values to diminish machining errors. The results indicate that the method can diminish diameter errors more than 70%, greatly improve the machining accuracy of bars.
基金Projects(2012ZX04010-011,2009ZX02037-02) supported by the Key National Science and Technology Project of China
文摘In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error model for the laser annealing table was established. It supports the identification of 7 geometric errors affecting the annealing accuracy. An original identification method was presented to recognize these geometric errors. Positioning errors of 5 lines in the workspace were measured by a laser interferometer, and the 7 geometric errors were identified by the proposed algorithm. Finally, a software-based error compensation method was adopted, and a compensation mechanism was developed in a postprocessor based on LabVIEW. The identified geometric errors can be compensated by converting ideal NC codes to actual NC codes. A validation experiment has been conducted on the laser annealing table, and the results indicate that positioning errors of two validation lines decreased from ±37 μm and ±33 μm to ±5 μm and ±4.5 μm, respectively. The geometric error modeling, identification and compensation method presented in this work can be straightforwardly extended to any configurations of 2-dimensional worktable.
基金Supported by the National Natural Science Foundation of China(51275145)
文摘According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.
基金Supported by China Scholarship Council(CSC),Deutscher Akademischer Austausch Dienst(DAAD),National Natural Science Foundation of China(60375011,60575028)Natural Science Foundation of Anhui Province(04042044)Supported by Program for New Century Excellent Talents in University(NCET-04-0560)
文摘Rotationally symmetric triangulation(RST)sensor has more flexibility and less uncertainty limits because of the abaxial rotationally symmetric optical system.But if the incident laser is eccentric,the symmetry of the image will descend,and it will result in the eccentric error especially when some part of the imaged ring is blocked.The model of rotationally symmetric triangulation that meets the Schimpflug condition is presented in this paper.The error from eccentric incident laser is analysed.It is pointed out that the eccentric error is composed of two parts,one is a cosine in circumference and proportional to the eccentric departure factor,and the other is a much smaller quadric factor of the departure.When the ring is complete,the first error factor is zero because it is integrated in whole ring, but if some part of the ring is blocked,the first factor will be the main error.Simulation verifies the result of the a- nalysis.At last,a compensation method to the error when some part of the ring is lost is presented based on neural network.The results of experiment show that the compensation will make the absolute maximum error descend to half,and the standard deviation of error descends to 1/3.
文摘The frictional properties of micro bearings have strong influence on the performance of the whole system because of tiny scale of micro-electromechanical system (MEMS). To develop micro bearings with low friction,it is important to evaluate the friction behaviors on the micro bearing. The testing system and the principle to evaluate the tribological performance of micromachining work-pieces under the load of mill Newton scale is introduced in paper "A new approach to measure the friction coefficient of micro journal bearings" of Yao et al,. But as the tribological force is faint in micro scale, the measured force is influenced a lot by the testing error. As the equation of that of Yao’s paper is very sensitive to the measured force, the tested result is influenced remarkably by testing error. So it is hard to get precision result. To solve this problem, the test system with new compensation method is introduced to precisely evaluate tribological performance under mill scale. The new metrology method is developed by means of the error compensation from two sets of testing data. The data are the force collected respectively when the friction counterparts rotate in CW(clockwise) and CCW(counter-clockwise) direction. So we deduce the equation of friction coefficient respctively on the condition of journal running in CCW and CW direction. As condition of measuring those two friciton coefficients are alike except the running direction of journal, and then the friction coefficient should be the same because this difference of direction has no influence on the fricition coefficients. Considering this, we unite the both equation, make the data measured in different subtract each other in the equation, and then a new equation can be gotten. This new equation enhances the metrology precision of friction coefficient theoretically thanks to the counteracting of error values in the equation. Using this method we testing the friction of high speed steel journal with hard alloy bearing. The result shows the new compensation method has better precision and repetition than CW and CCW method thanks to the error resistance.
文摘Some methods which use an optical tracker(OT) as a standard reference of electromagnetic tracker(EMT) were proposed in order to compensate the output error of electromagnetic tracker. Usually,they use a magneto-optic tool to collect the outputs of OT and EMT simultaneously,and then compare the output of OT with that of EMT to compensate the error of EMT. Although the outputs of EMT and OT can be matched each other by using a time stamp which denotes when the acquirement command is sent,but the accuracy will decrease if the tool moves faster for the errors of the time stamp itself. A rapid method for compensating EMT output error is proposed. A particular scan mode of the magneto-optic tool is designed for collecting EMT and OT outputs,and a data registration method is proposed to match the outputs of EMT and OT. The simulated results show that the output error of EMT can be decreased efficiently and the accuracy of the compensation can be improved by about 15% compared with that of the existing methods.
基金supported by the National Natural Science Foundation of China(61701140).
文摘To analyze the influence of time synchronization error,phase synchronization error,frequency synchronization error,internal delay of the transceiver system,and range error and angle error between the unit radars on the target detection performance,firstly,a spatial detection model of distributed high-frequency surface wave radar(distributed-HFSWR)is established in this paper.In this model,a method for accurate extraction of direct wave spectrum based on curve fitting is proposed to obtain accurate system internal delay and frequency synchronization error under complex electromagnetic environment background and low signal to noise ratio(SNR),and to compensate for the shift of range and Doppler frequency caused by time-frequency synchronization error.The direct wave component is extracted from the spectrum,the range estimation error and Doppler estimation error are reduced by the method of curve fitting,and the fitting accuracy of the parameters is improved.Then,the influence of frequency synchronization error on target range and radial Doppler velocity is quantitatively analyzed.The relationship between frequency synchronization error and radial Doppler velocity shift and range shift is given.Finally,the system synchronization parameters of the trial distributed-HFSWR are obtained by the proposed spectrum extraction method based on curve fitting,the experimental data is compensated to correct the shift of the target,and finally the correct target parameter information is obtained.Simulations and experimental results demonstrate the superiority and correctness of the proposed method,theoretical derivation and detection model proposed in this paper.
文摘In the field of deep space exploration,the rapid development of terahertz spectrometer has put forward higher requirements to the back-end chirp transform spectrometer(CTS)system.In order to simultaneously meet the measurement requirements of wide bandwidth and high accuracy spectral lines,we built a CTS system with an analysis bandwidth of 1 GHz and a frequency resolution of 100 kHz around the surface acoustic wave(SAW)chirp filter with a bandwidth of 1 GHz.In this paper,the relationship between the CTS nonlinear phase error shift model and the basic measurement parameters is studied,and the effect of CTS phase mismatch on the pulse compression waveform is analyzed by simulation.And the expander error optimization method is proposed for the problem that the large nonlinear error of the expander leads to the unbalanced response of the CTS system and the serious distortion of the compressed pulse waveform under large bandwidth.It is verified through simulation and experiment that the method is effective for reducing the root mean square error(RMSE)of the phase of the expander from 18.75°to 6.65°,reducing the in-band standard deviation of the CTS frequency resolution index from 8.43 kHz to 4.72 kHz,solving the problem of serious distortion of the compressed pulse waveform,and improving the uneven CTS response under large bandwidth.
文摘摆线泵转子的齿廓形状和加工精度决定了齿轮泵容腔的密封性,进而影响吸油和压油等运动特性。然而,转子的齿廓形状多是企业根据自身实际需求自行设计的,这就造成齿廓误差测量过程中的测量基准和设计基准不一致,测量结果更无法准确反映转子的齿廓加工质量。鉴于此,将企业设计的产品模型数据交互规范(Standard for the Exchange of Product model data, STEP)齿廓作为测量所必需的基准数据,在使用一维测头的国产齿轮测量中心上完成了转子齿廓的快速检测,采用重构及匹配等补偿处理方法,实现了摆线泵转子误差的精确评定。结果表明,该方法具有较好的柔性,对于复杂齿面的精确测量和评定具有重要的理论意义。
基金supported by the National Nature Science Foundation of China(61304223)the Aeronautical Science Foundation of China(2016ZA52009)the Research Fund for the Doctoral Program of Higher Education of China(20123218120015)
基金supported by the National Natural Science Foundation of China(6112010600461225005)
文摘A grating lobes suppression method for chirp-subpulse stepped frequency（CSSF） signals is proposed, which is applied to deformation monitoring using the ground based synthetic aperture radar（GB-SAR） system. This method is based on accurate estimation and correction of the phase and amplitude error along two dimensions（range and azimuth）, i.e., the error estimation inside the subpulse（in-subpulse error） and across the stepped frequency subpulses（cross-subpulse error） of transmitted CSSF signals. Validated both with simulated data and experimental data recorded in the deformation monitoring campaign, it can be seen that the method as well as the relative conclusions can be fully and effectively applied to most of the stepped frequency systems.
基金supported by the National Key R&D Program of China (2018YFC1508502)the National Natural Science Foundation of China (41601569,61661043,61631011)the Science and Technology Innovation Guidance Project of Inner Mongolia Autonomous Region (2019GG139,KCBJ2017,KCBJ 2018014,2019ZD022)。
文摘In recent years, ground-based micro-deformation monitoring radar has attracted much attention due to its excellent monitoring capability. By controlling the repeated campaigns of the radar antenna on a fixed track, ground-based micro-deformation monitoring radar can accomplish repeat-pass interferometry without a space baseline and thus obtain highprecision deformation data of a large scene at one time. However, it is difficult to guarantee absolute stable installation position in every campaign. If the installation position is unstable, the stability of the radar track will be affected randomly, resulting in time-varying baseline error. In this study, a correction method for this error is developed by analyzing the error distribution law while the spatial baseline is unknown. In practice, the error data are first identified by frequency components, then the data of each one-dimensional array(in azimuth direction or range direction) are grouped based on numerical distribution period, and finally the error is corrected by the nonlinear model established with each group.This method is verified with measured data from a slope in southern China, and the results show that the method can effectively correct the time-varying baseline error caused by rail instability and effectively improve the monitoring data accuracy of groundbased micro-deformation radar in short term and long term.
基金Project(2006C11200) supported by the Science and Technology Project of Zhejiang Province of China
文摘In order to improve the video quality of transmission with data loss,a spatial and temporal error concealment method was proposed,which considered both the state information of the network and the perceptual weight of the video content.The proposed method dynamically changed the reliability weight of the neighboring macroblock,which was used to conceal the lost macroblocks according to the packet loss rate of the current channel state.The perceptual weight map was utilized as side information to do weighted pixel interpolation and side-match based motion compensation for spatial and temporal error concealment,respectively.And the perceptual weight of the neighboring macroblocks was adaptively modified according to the perceptual weight of the lost macroblocks.Compared with the method used in H.264 joint model,experiment results show that the proposed method performs well both in subjective video quality and objective video quality,and increases the average peak signal-to-noise ratio(PSNR) of the whole frame by about 0.4 dB when the video bitstreams are transmitted with packets loss.
