The lithology of fracture zone which was developed at the dam foundation of a hydropower station is weak sandstone with poor integrity and pore cementation contact.Its creep properties have a significant impact on the...The lithology of fracture zone which was developed at the dam foundation of a hydropower station is weak sandstone with poor integrity and pore cementation contact.Its creep properties have a significant impact on the deformation and stability of the dam.Based on the characteristics of loose organizational structure,high moisture content and poor mechanical properties,the triaxial compression tests and creep tests were carried out,respectively.The results show significant non-linear,low strength and no obvious strength peaks.Both axial and lateral strains are achieved more than 3%when the tests are failed.The weak sandstone has a significant creep property,but only transient and steady state appear under low stress.Increased stress causes creep intensified and lateral strain gradually exceeds axial strain.In the failure stage,it has characteristics of large axial plastic deformation,obvious volumetric ductility dilation and large steady creep rate.The accelerated creep appears shortly after transient loading under confining of pressures 1.0 MPa and 1.5 MPa.Therefore,an improved Burgers creep model considering the non-linear characteristics of weak sandstone is built based on hyperbolic equation and the creep parameters are identified.This model can well describe the creep properties of weak sandstone.展开更多
In order to investigate the influence of intermediate principal stress on the stress-strain and strength behaviour of a coarse-grained soil, a series of true triaxial tests were performed. The tests were conducted in ...In order to investigate the influence of intermediate principal stress on the stress-strain and strength behaviour of a coarse-grained soil, a series of true triaxial tests were performed. The tests were conducted in a recently developed true triaxial apparatus with constant minor principal stress σ3 and constant value of intermediate principal stress ratio b=（σ2-σ3）/（σ1-σ3） （al is the vertical stress, and % is the horizontal stress）. It is found that the intermediate principal strain, ε2, increases from negative to positive value with the increase of parameter b from zero to unity under a constant minor principal stress. The minor principal strain, ε3, is always negative. This implies that the specimen exhibits an evident anisotropy. The relationship between b and friction angle obtained from the tests is different from that predicted by LADE-DUNCAN and MATSUOKA-NAKAI criteria. Based on the test results, an empirical equation of g（b） that is the shape function of the failure surface on re-plane was presented. The proposed equation is verified to be reasonable by comparing the predicted results using the equation with true triaxial test results of soils, such as coarse-grained soils in this study, sands and gravels in other studies.展开更多
The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures hav...The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.展开更多
Triaxial creep tests were carried out under seepage pressure by using rock servo-controlled triaxial rheology testing equipment. Based on experimental results, rock rheological properties influenced by seepage-stress ...Triaxial creep tests were carried out under seepage pressure by using rock servo-controlled triaxial rheology testing equipment. Based on experimental results, rock rheological properties influenced by seepage-stress coupling were studied, and variations of seepage rate with time in complete creep processes of rock were analyzed. It is shown that, when the applied stress is less than failure stress level, the creep deformation is not obvious, and its main form is steady-state creep. When applied stress level is greater than or less than but close to fracture stress, it is easier to see the increase of creep deformation and the more obvious accelerative creep characteristics. The circumferential creep deformation is obviously higher than the axial creep deformation. At the stage of steady-state creep, the average of seepage flow rate is about 4.7×10-9 rn/s at confining pressure （tr3） of 2 MPa, and is about 3.9×10-9 m/s at a3 of 6 MPa. It is seen that the seepage flow rate at or3 of 2 MPa in this case is obviously larger than that at tr3 of 6 MPa. At the stage of creep acceleration, the seepage flow rate is markedly increased with the increase of time. The variation of rock permeability is directly connected to the growth and evolution of creep crack. It is suggested that the permeability coefficient in complete creep processes of rock is not a constant, but is a function of rock creep strain, confining pressure, damage variable and pore water pressure. The results can be considered to provide a reliable reference for the establishment of rock rheological model and parameter identification.展开更多
The shear strength parameters for geotechnical designs are obtained mainly from consolidated drained （CD） or consolidated undrained （CU） triaxial tests. However, during construction, the excess pore-air pressure g...The shear strength parameters for geotechnical designs are obtained mainly from consolidated drained （CD） or consolidated undrained （CU） triaxial tests. However, during construction, the excess pore-air pressure generally dissipates instantaneously while the excess pore-water pressure dissipates with time. This condition needs to be simulated in a constant water content （CW） triaxial test. The study on Yunnan red clay is carried out to investigate the soil-water characteristics and the shear strength characteristics under the constant water content condition. Osmotic technique is used to obtain the soil-water characteristic curve. A series of CW triaxial tests are conducted on statically compacted specimens. The experimental results show that the soil-water characteristic curve has a low air entry value of 7 kPa due to large pores in non-uniform pore size distribution, and a high residual value exceeding 10 MPa. In addition, the initial degree of saturation and net confining stress play an important role in affecting the shear characteristics under the constant water content condition. Finally, a new semi-empirical shear strength model in terms of degree of saturation is proposed and then applied to Yuunan red clay. Simulation result shows that the model is capable of capturing some key features of soils. The model can be used in whole engineering practice range, covering both unsaturmed and saturated soils.展开更多
A series of triaxial compression tests for frozen clay were performed by KoDCGF （freezing with non-uniform temperature under loading after K0 consolidation） method and GFC （freezing with non-uniform temperature wit...A series of triaxial compression tests for frozen clay were performed by KoDCGF （freezing with non-uniform temperature under loading after K0 consolidation） method and GFC （freezing with non-uniform temperature without experiencing Ko consolidation） method at various confining pressures and thermal gradients. The experimental results indicate that the triaxial compression strength for frozen clay in KoDCGF test increases with the increase of confining pressure, but it decreases as the confining pressure increases further in GFC test. In other words, the compression strength for frozen clay with identical confining pressure decreases with the increase in thermal gradient both in KoDCGF test and GFC test. The strength of frozen clay in KoDCGF test is dependent of pore ice strength, soil particle strength and interaction between soil skeleton and pore ice. The decrease of water content and distance between soil particles leads to the decrease of pore size and the increase of contact area between particles in KoDCGF test, which further results in a higher compression strength than that in GFC test. The compression strength for frozen clay with thermal gradient can be descried by strength for frozen clay with a uniform temperature identical to the temperature at the height of specimen where the maximum tensile stress appears.展开更多
In-situ rock failures can result from stress changes due to pure loading and/or unloading. Understanding of the damage evolution behavior in brittle rocks during loading and unloading is imperative for the designs of ...In-situ rock failures can result from stress changes due to pure loading and/or unloading. Understanding of the damage evolution behavior in brittle rocks during loading and unloading is imperative for the designs of rock structures. In this paper, we investigate the damage evolution characteristics of a granitic rock during loading and unloading after a series of triaxial experiments performed at different confining pressures. The axial stress-axial strain variations of the tested specimens revealed that the specimens undergoing unloading fail with a lower axial strain compared to the specimens failed purely by loading. Higher confining pressures were observed to exacerbate the difference. Volumetric strain versus axial strain curves indicated that the curves reverse the trend with the beginning of major damage of specimens. We suggest here a new form of equation to describe the secant modulus variation of brittle rocks against the axial stress for the unloading process. Failure mechanisms of tested specimens showed two distinct patterns, namely, specimens under pure loading failed with a single distinct shear fracture while for the unloading case specimens displayed multiple intersecting fractures. In addition, analysis of the evolution of dissipation and elastic energy during deformation of the specimens under loading and unloading conditions showed differentiable characteristics. Moreover, we evaluated the variations of two damage indices defined based on the energy dissipation and secant modulus evolution during deformation and observed that both of them satisfactorily distinguish key stages of damage evolution.展开更多
Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the...Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the effects of discontinuities on cutting characteristics and cutting efficiency. In laboratory tests, five propagation patterns of radial cracks are observed. And in the numerical tests, firstly, it is similar to laboratory tests that cracks ahead of cutters mainly initiate from the crushed zone, and some minor cracks will initiate from joints. The cracks initiating from crushed zones will run through the thinner joints while they will be held back by thick joints. Cracks tend to propagate towards the tips of embedded cracks, and minor cracks will initiate from the tips of embedded cracks, which may result in the decrease of specific area, and disturbing layers play as ‘screens', which will prevent cracks from developing greatly. The peak penetration forces, the consumed energy in the penetration process and the uniaxial compression strength will decrease with the increase of discontinuities. The existence of discontinuities will result in the decrease of the cutting efficiency when the spacing between cutters is 70 mm. Some modifications should be made to improve the efficiency when the rocks containing groups of discontinuities are encountered.展开更多
Combined with numerical simulation, the influence of confining stress on cutting process, fracture conditions and cutting efficiencies of soft and hard rock has been conducted on the triaxial testing machine(TRW-3000)...Combined with numerical simulation, the influence of confining stress on cutting process, fracture conditions and cutting efficiencies of soft and hard rock has been conducted on the triaxial testing machine(TRW-3000) designed and manufactured in Central South University(China). Results are obtained by performing analysis on the fracture scopes of cement and granite plates,the characteristics of cutting force in cutting processes and the cutting efficiency. Firstly, the increase of latitude fracture scope and the decrease of longitude fracture scope are both more notable in the tests conducted on cement plates subjected to the increasing confining stresses; secondly, the increase tendency of peak penetration forces obtained from tests conducted on granite plates is more obvious, however, the increase tendencies of average penetration forces achieved from cement and granite plates are close to each other; thirdly, the cutting efficiency could be improved by increasing the spacing between cutters when the confining stress which acts on soft and hard rock increases in a certain degree, and the cutting efficiency of soft rock is more sensitive to the varying confining stresses.展开更多
Deformation and failure of deep clay samples are closely related to energy changes.Investigating the energy conversion and damage behavior of deep clay during loading and unloading tests has important significance for...Deformation and failure of deep clay samples are closely related to energy changes.Investigating the energy conversion and damage behavior of deep clay during loading and unloading tests has important significance for prevention-control of soil destabilization damage caused by mine shaft excavation.In the present work,triaxial tests of consolidated clay under different stress paths and stress rates were conducted.The results reveal that the mechanical properties of soils have strong stress rate effects and the samples mainly experience energy storage in the elastic stage,after that,the energy conversion mainly undergoes an increase of dissipative energy and release of elastic energy,which is also confirmed by the results of the analysis in the subsequent CT tests.Two damage indicators were compared,finding that the indicator based on dissipative energy has more obvious differences in two stress paths and can be used as a better indicator to describe the damage evolution of soils.Finally,in the triaxial shear test,due to the unloading effect of confining pressure,the damage of soils increased more rapidly near breaking than in the triaxial compression test,which indicates that the damage caused by unloading on deep soil is more abrupt than that caused by loading.展开更多
Strainburst is one type of rockburst that generally occurs in deep tunnel.In this study,the strainburst behaviors of marble specimens were investigated under tunnel-excavation-induced stress condition,and two stress p...Strainburst is one type of rockburst that generally occurs in deep tunnel.In this study,the strainburst behaviors of marble specimens were investigated under tunnel-excavation-induced stress condition,and two stress paths were designed,a commonly used stress path in true triaxial unloading rockburst tests and a new test path in which the intermediate principal stress was varied.During the tests,a high-speed camera was used to record the strainburst process,and an acoustic emission(AE)monitoring system was used to monitor the AE characteristics of failure.In these two stress paths,all the marble specimens exhibited strainbursts;however,when the intermediate principal stress was varied,the rockburst became more violent.The obtained results indicate that the intermediate principal stress has a significant effect on rockburst behavior of marble.Under a higher intermediate principal stress before the unloading,more elastic strain energy was accumulated in the specimen,and the cumulative AE energy was higher in the rockburst-induced failure,i.e.,more elastic strain energy was released during the failure.Therefore,more violent failure was observed:more rock fragments with a higher mass and larger size were ejected outward.展开更多
To investigate the acoustic emission(AE)precursors of coarse-grained hard rock instability,an experimental study on the rockburst and slabbing process of granite was carried out using a true triaxial test system.The e...To investigate the acoustic emission(AE)precursors of coarse-grained hard rock instability,an experimental study on the rockburst and slabbing process of granite was carried out using a true triaxial test system.The evolution of the AE signals was monitored and analyzed in terms of the AE hit rate,fractal dimension of the AE hit number,AE count rate,b-value,dominant frequency and microcrack type.The test results show that after rock slabbing occurs,the AE precursors that can be used to predict the final dynamic instability(rockburst)are as follows:indicators such as the AE hit rate and AE count rate suddenly increase and then suddenly decrease;the AE hit rate exhibits a“quiet period”;during the“quiet period”,a small number of high-amplitude and low-frequency hits occur,and the signals corresponding to shear fracture continue to increase.The AE precursors for the final static instability(spalling)are as follows:both the AE hit rate and the b-value continuously decrease,and intermittent sudden increases appear in the high-frequency hits or the AE count rate.展开更多
As a widely distributed geological and engineering material,the soil-rock mixture always undergoes frequentative and short-term freeze-thaw cycles in some regions.Its internal structure is destroyed seriously,but the ...As a widely distributed geological and engineering material,the soil-rock mixture always undergoes frequentative and short-term freeze-thaw cycles in some regions.Its internal structure is destroyed seriously,but the damage mechanism is not clear.Based on the damage factor,the damage research of properties of soil-rock mixture after different times of freeze-thaw cycles is investigated.Firstly,the size-distributed subgrade gravelly soil samples are prepared and undergo different times of freeze-thaw cycles periodically(0,3,6,10),and indoor large-scale triaxial tests are completed.Secondly,the degradation degree of elastic modulus is considered as a damage factor,and applied to macro damage analysis of soil-rock mixture.Finally,the mesoscopic simulation of the experiments is achieved by PFC3D,and the influence on strength between soil-rock particles caused by freeze-thaw cycles is analyzed.The results show that freeze-thaw cycles cause internal damage of samples by weakening the strength between mesoscopic soil-rock particles,and ultimately affect the macro properties.After freeze-thaw cycles,on the macro-scale,elastic modulus and shear strength of soil-rock mixture both decrease,and the decreasing degree is related to the times of cycles with the mathmatical quadratic form;on the meso-scale,freeze-thaw cycles mainly cause the degradation of the strength between soil-rock particles whose properties are different significantly.展开更多
Recycled waste tires when mixed with soil can play an important role as lightweight materials in retaining walls and embankments, machine foundations and railroad track beds in seismic zones. Having high damping chara...Recycled waste tires when mixed with soil can play an important role as lightweight materials in retaining walls and embankments, machine foundations and railroad track beds in seismic zones. Having high damping characteristic, rubbers can be used as either soil alternative or mixed with soil to reduce vibration when seismic loads are of great concern. Therefore, the objective of this work was to evaluate the dynamic properties of such mixtures prior to practical applications. To this reason, torsional resonant column and dynamic triaxial experiments were carried out and the effect of the important parameters like rubber content and ratio of mean grain size of rubber solids versus soil solids(D50,r/D50,s) on dynamic response of mixtures in a range of low to high shearing strain amplitude from about 4×10-4% to 2.7% were investigated. Considering engineering applications, specimens were prepared almost at the maximum dry density and optimum moisture content to model a mixture layer above the ground water table and in low precipitation region. The results show that tire inclusion significantly reduces the shear modulus and increases the damping ratio of the mixtures. Also decrease in D50,r/D50,s causes the mixture to exhibit more rubber-like behavior. Finally, normalized shear modulus versus shearing strain amplitude curve was proposed for engineering practice.展开更多
Although the dynamic properties of subgrade soils in seasonally frozen areas have already been studied, few researchers have considered the influence of shallow groundwater during the freeze–thaw(F–T) cycles. So a m...Although the dynamic properties of subgrade soils in seasonally frozen areas have already been studied, few researchers have considered the influence of shallow groundwater during the freeze–thaw(F–T) cycles. So a multifunctional F–T cycle system was developed to imitate the groundwater recharge in the subgrade during the freezing process and a large number of dynamic triaxial experiments were conducted after the F–T cycles. Some significant factors including the F–T cycle number, compaction degree, confining pressure, cyclic deviator stress, loading frequency, and water content were investigated for the resilient modulus of soils. The experimental results indicated that the dynamic resilient modulus of the subgrade was negatively correlated with the cyclic deviator stress, F–T cycle number, and initial water content, whereas the degree of compaction, confining pressure, and loading frequency could enhance the resilient modulus. Furthermore, a modified model considering the F–T cycle number and stress state was established to predict the dynamic resilient modulus. The calculated results of this modified model were very close to the experimental results. Consequently, calculation of the resilient modulus for F–T cycles considering the dynamic load was appropriate. This study provides reference for research focusing on F–T cycles with groundwater supply and the dynamic resilient moduli of subgrade soils in seasonally frozen areas.展开更多
The state of clean sand was mainly dependent on its void ratio(density)and confining stress that greatly influenced the mechanical behavior(compression,dilatancy and liquefaction)of clean sand.Confirming whether the c...The state of clean sand was mainly dependent on its void ratio(density)and confining stress that greatly influenced the mechanical behavior(compression,dilatancy and liquefaction)of clean sand.Confirming whether the confining stress was a state variable of sand required precise element tests at different confining stress,especially the tests under very low confining stress whose test data were very limited.In this study,static-dynamic characteristics of clean sand was comprehensively investigated by a unified test program under low and normal confining stress ranging from 5 to 98 kPa,under monotonic/cyclic and drained/undrained conditions,together with the literature available data under confining stress of 1.0 to 3.0 MPa.For monotonic loading tests,the contraction/dilation phase transition was observed for loose sand at low confining stress,and dilatancy angles were stress-dependent.In addition,the liquefaction resistance was observed to increase with reducing of confining stress,and the axial strain varied from compressive to dilative when confining stress increased.Special attention was also paid to the enhancement effect of membrane,and it was observed that its influence on the test results was limited.In addition,the experimental results were proved reliable by reproducibility.展开更多
An incrementally nonlinear hypoplastic constitutive model was introduced, which was developed without recourse to the concepts in elastoplasticity theory such as yield surface, plastic potential and the decomposition ...An incrementally nonlinear hypoplastic constitutive model was introduced, which was developed without recourse to the concepts in elastoplasticity theory such as yield surface, plastic potential and the decomposition of the deformation into elastic and plastic parts. Triaxial drained tests on rockfill were conducted on a large scale triaxial apparatus under two types of stress paths, which were the stress paths of constant stress ratio and the complex stress paths with transitional features. Motivated by the effect of stress path, the Gudehus-Bauer hypoplastic model was improved by considering the parameter variations with different ratios of stress increment. Fitting parameter a presents a piecewise linear relationship with cosine of the slope angle θ determined by instantaneous stress path. The improved hypoplastic model can present peak stress increasing and volumetric strain changing from dilatancy to contractancy with the increase of transitional confining pressure σ3t and the decrease of slope angle θ of stress path. Compared with the test data, it is shown that the model is capable of fully considering the effect of stress path on rockfill.展开更多
By using large scale triaxial shearing apparatus,consolidated-drained shear tests were conducted on coarse-grained soil with different gradations.In order to describe their deformation rules,three main characteristics...By using large scale triaxial shearing apparatus,consolidated-drained shear tests were conducted on coarse-grained soil with different gradations.In order to describe their deformation rules,three main characteristics of tangent Poisson ratio curves were summarized and the reason was revealed by dividing the movement of soil particles into two kinds: the movement of fine particles and the movement of coarse particles.Then,a volumetric strain expression and a tangent Poisson ratio expression were put forward,and two defects of widely used Duncan-Chang model were fixed.Results calculated from them agree well with test results.There are three parameters,namely L,G and F,in this new model.Parameter L reflects the dilatancy of a specimen and L=4 can be used as a criterion to estimate whether a certain kind of soil has dilatancy quality or not.Parameters G and F relate to the initial slope of tangent Poisson ratio curves,and G=F=0 indicates a special situation which happens in dense granular material of the same diameter.Influences of various gradations on volume deformation are mainly reflected in parameter L which is smaller when there are more gravels in specimens.展开更多
A moisture-content based constitutive model was proposed based on the hyperbolic model as an attempt to move towards the implementation of unsaturated soil mechanics into routine geotechnical engineering practice. The...A moisture-content based constitutive model was proposed based on the hyperbolic model as an attempt to move towards the implementation of unsaturated soil mechanics into routine geotechnical engineering practice. The stress-strain behavior of in-situ soil at a depth of 5 m was investigated by conducting undrained triaxial compression tests using the remolded soil samples. The test results show that the stress-strain relationship of unsaturated cohesive soil is still hyperbolic. The values of parameters a and b given in the model decrease with increasing the confining pressure for soil samples with the same moisture content and increase with increasing the moisture content for soil samples under the same confining pressure. The relationships between parameters a, b and moisture content were studied for confining pressures of 100, 150, 200 and 250 kPa. The comparison between the measured and predicted stress-strain curves for an additional group of soil samples, having a moisture content of 25.4%, shows that the proposed moisture content-dependent hyperbolic model provides a good prediction of stress-strain behavior of unsaturated cohesive soil.展开更多
Isotropic consolidation test and consolidated-undrained triaxial test were first undertaken to obtain the parameters of the modified cam-clay(MCC)model and the behavior of natural clayey soil.Then,for the first time,n...Isotropic consolidation test and consolidated-undrained triaxial test were first undertaken to obtain the parameters of the modified cam-clay(MCC)model and the behavior of natural clayey soil.Then,for the first time,numerical simulation of the two tests was performed by three-dimensional finite element method(FEM)using ABAQUS program.The consolidated-drained triaxial test was also simulated by FEM and compared with theoretical results of MCC model.Especially,the behaviors of MCC model during unloading and reloading were analyzed in detail by FEM.The analysis and comparison indicate that the MCC model is able to accurately describe many features of the mechanical behavior of the soil in isotropic consolidation test and consolidated-drained triaxial test.And the MCC model can well describe the variation of excess pore water pressure with the development of axial strain in consolidated-undrained triaxial test,but its ability to predict the relationship between axial strain and shear stress is relatively poor.The comparison also shows that FEM solutions of the MCC model are basically identical to the theoretical ones.In addition,Mandel-Cryer effect unable to be discovered by the conventional triaxial test in laboratories was disclosed by FEM.The analysis of unloading-reloading by FEM demonstrates that the MCC model disobeys the law of energy conservation under the cyclic loading condition if the elastic shear modulus is linearly pressure-dependent.展开更多
基金Project(2011CB013504)supported by the National Basic Research Program of ChinaProject(11172090)supported by the National Natural Science Foundation of China
文摘The lithology of fracture zone which was developed at the dam foundation of a hydropower station is weak sandstone with poor integrity and pore cementation contact.Its creep properties have a significant impact on the deformation and stability of the dam.Based on the characteristics of loose organizational structure,high moisture content and poor mechanical properties,the triaxial compression tests and creep tests were carried out,respectively.The results show significant non-linear,low strength and no obvious strength peaks.Both axial and lateral strains are achieved more than 3%when the tests are failed.The weak sandstone has a significant creep property,but only transient and steady state appear under low stress.Increased stress causes creep intensified and lateral strain gradually exceeds axial strain.In the failure stage,it has characteristics of large axial plastic deformation,obvious volumetric ductility dilation and large steady creep rate.The accelerated creep appears shortly after transient loading under confining of pressures 1.0 MPa and 1.5 MPa.Therefore,an improved Burgers creep model considering the non-linear characteristics of weak sandstone is built based on hyperbolic equation and the creep parameters are identified.This model can well describe the creep properties of weak sandstone.
基金Project(50639050) supported by the National Natural Science Foundation of China and Er-Tan Hydraulicpower Limited CompanyProject(50579014) supported by the National Natural Science Foundation of China+3 种基金Project(09KJD560003) supported by the Natural Science Foundation of Jiangsu Higher Education Institutions of ChinaProject(BK2007582) supported by Jiangsu Provincial Natural Science Foundation of ChinaProject(20070294002) supported by the Specialized Research Fund for the Doctoral Program of Higher Education of ChinaProject(GH200904) supported by Key Laboratory of Ministry of Education for Geomechanics and Embankment Engineering,Hohai University,China
文摘In order to investigate the influence of intermediate principal stress on the stress-strain and strength behaviour of a coarse-grained soil, a series of true triaxial tests were performed. The tests were conducted in a recently developed true triaxial apparatus with constant minor principal stress σ3 and constant value of intermediate principal stress ratio b=（σ2-σ3）/（σ1-σ3） （al is the vertical stress, and % is the horizontal stress）. It is found that the intermediate principal strain, ε2, increases from negative to positive value with the increase of parameter b from zero to unity under a constant minor principal stress. The minor principal strain, ε3, is always negative. This implies that the specimen exhibits an evident anisotropy. The relationship between b and friction angle obtained from the tests is different from that predicted by LADE-DUNCAN and MATSUOKA-NAKAI criteria. Based on the test results, an empirical equation of g（b） that is the shape function of the failure surface on re-plane was presented. The proposed equation is verified to be reasonable by comparing the predicted results using the equation with true triaxial test results of soils, such as coarse-grained soils in this study, sands and gravels in other studies.
文摘The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.
基金Projects(11172090,51009052,51109069) supported by the National Natural Science Foundation of ChinaProject(2011CB013504) supported by the National Basic Research Program of China
文摘Triaxial creep tests were carried out under seepage pressure by using rock servo-controlled triaxial rheology testing equipment. Based on experimental results, rock rheological properties influenced by seepage-stress coupling were studied, and variations of seepage rate with time in complete creep processes of rock were analyzed. It is shown that, when the applied stress is less than failure stress level, the creep deformation is not obvious, and its main form is steady-state creep. When applied stress level is greater than or less than but close to fracture stress, it is easier to see the increase of creep deformation and the more obvious accelerative creep characteristics. The circumferential creep deformation is obviously higher than the axial creep deformation. At the stage of steady-state creep, the average of seepage flow rate is about 4.7×10-9 rn/s at confining pressure （tr3） of 2 MPa, and is about 3.9×10-9 m/s at a3 of 6 MPa. It is seen that the seepage flow rate at or3 of 2 MPa in this case is obviously larger than that at tr3 of 6 MPa. At the stage of creep acceleration, the seepage flow rate is markedly increased with the increase of time. The variation of rock permeability is directly connected to the growth and evolution of creep crack. It is suggested that the permeability coefficient in complete creep processes of rock is not a constant, but is a function of rock creep strain, confining pressure, damage variable and pore water pressure. The results can be considered to provide a reliable reference for the establishment of rock rheological model and parameter identification.
基金Project(51068002) supported by the National Natural Science Foundation of ChinaProject(10-046-14-1) supported by Guangxi Key Laboratory of Geomechanics and Geotechnical Engineering,China
文摘The shear strength parameters for geotechnical designs are obtained mainly from consolidated drained （CD） or consolidated undrained （CU） triaxial tests. However, during construction, the excess pore-air pressure generally dissipates instantaneously while the excess pore-water pressure dissipates with time. This condition needs to be simulated in a constant water content （CW） triaxial test. The study on Yunnan red clay is carried out to investigate the soil-water characteristics and the shear strength characteristics under the constant water content condition. Osmotic technique is used to obtain the soil-water characteristic curve. A series of CW triaxial tests are conducted on statically compacted specimens. The experimental results show that the soil-water characteristic curve has a low air entry value of 7 kPa due to large pores in non-uniform pore size distribution, and a high residual value exceeding 10 MPa. In addition, the initial degree of saturation and net confining stress play an important role in affecting the shear characteristics under the constant water content condition. Finally, a new semi-empirical shear strength model in terms of degree of saturation is proposed and then applied to Yuunan red clay. Simulation result shows that the model is capable of capturing some key features of soils. The model can be used in whole engineering practice range, covering both unsaturmed and saturated soils.
基金Project(50534040) supported by the National Natural Science Foundation of ChinaProject(20110491489) supported by China Postdoctoral Science FoundationProject(2011QNA03) supported by Fundamental Research Funds for the Central Universities of China
文摘A series of triaxial compression tests for frozen clay were performed by KoDCGF （freezing with non-uniform temperature under loading after K0 consolidation） method and GFC （freezing with non-uniform temperature without experiencing Ko consolidation） method at various confining pressures and thermal gradients. The experimental results indicate that the triaxial compression strength for frozen clay in KoDCGF test increases with the increase of confining pressure, but it decreases as the confining pressure increases further in GFC test. In other words, the compression strength for frozen clay with identical confining pressure decreases with the increase in thermal gradient both in KoDCGF test and GFC test. The strength of frozen clay in KoDCGF test is dependent of pore ice strength, soil particle strength and interaction between soil skeleton and pore ice. The decrease of water content and distance between soil particles leads to the decrease of pore size and the increase of contact area between particles in KoDCGF test, which further results in a higher compression strength than that in GFC test. The compression strength for frozen clay with thermal gradient can be descried by strength for frozen clay with a uniform temperature identical to the temperature at the height of specimen where the maximum tensile stress appears.
基金Projects(51774187,51324744,51374129)supported by the National Natural Science Foundation of ChinaProject(71380100006)supported by the Innovation Foundation of Doctoral Student in Hunan Province,China+1 种基金Project(2017SK2280)supported by the Key Research and Development Program of Hunan Provincial Science and Technology Department,ChinaProject(17A184)supported by the Key Research Foundation of Education Bureau of Hunan Province,China
文摘In-situ rock failures can result from stress changes due to pure loading and/or unloading. Understanding of the damage evolution behavior in brittle rocks during loading and unloading is imperative for the designs of rock structures. In this paper, we investigate the damage evolution characteristics of a granitic rock during loading and unloading after a series of triaxial experiments performed at different confining pressures. The axial stress-axial strain variations of the tested specimens revealed that the specimens undergoing unloading fail with a lower axial strain compared to the specimens failed purely by loading. Higher confining pressures were observed to exacerbate the difference. Volumetric strain versus axial strain curves indicated that the curves reverse the trend with the beginning of major damage of specimens. We suggest here a new form of equation to describe the secant modulus variation of brittle rocks against the axial stress for the unloading process. Failure mechanisms of tested specimens showed two distinct patterns, namely, specimens under pure loading failed with a single distinct shear fracture while for the unloading case specimens displayed multiple intersecting fractures. In addition, analysis of the evolution of dissipation and elastic energy during deformation of the specimens under loading and unloading conditions showed differentiable characteristics. Moreover, we evaluated the variations of two damage indices defined based on the energy dissipation and secant modulus evolution during deformation and observed that both of them satisfactorily distinguish key stages of damage evolution.
基金Project(2013CB035401) supported by the National Basic Research Program of ChinaProject(51174228) supported by the National Natural Science Foundation of China+1 种基金Project(71380100003) supported by Hunan Provincial Innovation Foundation for Postgraduate,ChinaProject(201304) supported by Open Research Fund of Hunan Province Key Laboratory of Safe Mining Techniques of Coal Mines(Hunan University of Science and Technology),China
文摘Based on the triaxial testing machine and discrete element method, the effects of embedded crack on rock fragmentation are investigated in laboratory tests and a series of numerical investigations are conducted on the effects of discontinuities on cutting characteristics and cutting efficiency. In laboratory tests, five propagation patterns of radial cracks are observed. And in the numerical tests, firstly, it is similar to laboratory tests that cracks ahead of cutters mainly initiate from the crushed zone, and some minor cracks will initiate from joints. The cracks initiating from crushed zones will run through the thinner joints while they will be held back by thick joints. Cracks tend to propagate towards the tips of embedded cracks, and minor cracks will initiate from the tips of embedded cracks, which may result in the decrease of specific area, and disturbing layers play as ‘screens', which will prevent cracks from developing greatly. The peak penetration forces, the consumed energy in the penetration process and the uniaxial compression strength will decrease with the increase of discontinuities. The existence of discontinuities will result in the decrease of the cutting efficiency when the spacing between cutters is 70 mm. Some modifications should be made to improve the efficiency when the rocks containing groups of discontinuities are encountered.
基金Project(2013CB035401)supported by the National Basic Research Program of ChinaProject(51174228)supported by the National Natural Science Foundation of China+1 种基金Project(201304)supported by Open Research Fund of Hunan Province Key Laboratory of Safe Mining Techniques of Coal Mines(Hunan University of Science and Technology),ChinaProject(14C0746)supported by the Education Department of Hunan Province,China
文摘Combined with numerical simulation, the influence of confining stress on cutting process, fracture conditions and cutting efficiencies of soft and hard rock has been conducted on the triaxial testing machine(TRW-3000) designed and manufactured in Central South University(China). Results are obtained by performing analysis on the fracture scopes of cement and granite plates,the characteristics of cutting force in cutting processes and the cutting efficiency. Firstly, the increase of latitude fracture scope and the decrease of longitude fracture scope are both more notable in the tests conducted on cement plates subjected to the increasing confining stresses; secondly, the increase tendency of peak penetration forces obtained from tests conducted on granite plates is more obvious, however, the increase tendencies of average penetration forces achieved from cement and granite plates are close to each other; thirdly, the cutting efficiency could be improved by increasing the spacing between cutters when the confining stress which acts on soft and hard rock increases in a certain degree, and the cutting efficiency of soft rock is more sensitive to the varying confining stresses.
基金Project(2016YFC0600904)supported by the National Key Research and Development Program of ChinaProject(BK20200653)supported by the Natural Science Foundation of Jiangsu,ChinaProject(2020M681768)supported by the China Postdoctoral Science Foundation。
文摘Deformation and failure of deep clay samples are closely related to energy changes.Investigating the energy conversion and damage behavior of deep clay during loading and unloading tests has important significance for prevention-control of soil destabilization damage caused by mine shaft excavation.In the present work,triaxial tests of consolidated clay under different stress paths and stress rates were conducted.The results reveal that the mechanical properties of soils have strong stress rate effects and the samples mainly experience energy storage in the elastic stage,after that,the energy conversion mainly undergoes an increase of dissipative energy and release of elastic energy,which is also confirmed by the results of the analysis in the subsequent CT tests.Two damage indicators were compared,finding that the indicator based on dissipative energy has more obvious differences in two stress paths and can be used as a better indicator to describe the damage evolution of soils.Finally,in the triaxial shear test,due to the unloading effect of confining pressure,the damage of soils increased more rapidly near breaking than in the triaxial compression test,which indicates that the damage caused by unloading on deep soil is more abrupt than that caused by loading.
基金Project(2016YFC0801403) supported by the National Key Research and Development Program of ChinaProject(2017RCJJ012) supported by the Scientific Research Foundation of Shandong University of Science and Technology for Recruited Talents,China+1 种基金Project(ZR2018MEE009) supported by the Shandong Provincial Natural Science Foundation,ChinaProject(MDPC2017ZR04) supported by the Open Project Fund for State Key Laboratory of Mining Disaster Prevention and Control Co-founded by Shandong Province and the Ministry of Science and Technology of China
文摘Strainburst is one type of rockburst that generally occurs in deep tunnel.In this study,the strainburst behaviors of marble specimens were investigated under tunnel-excavation-induced stress condition,and two stress paths were designed,a commonly used stress path in true triaxial unloading rockburst tests and a new test path in which the intermediate principal stress was varied.During the tests,a high-speed camera was used to record the strainburst process,and an acoustic emission(AE)monitoring system was used to monitor the AE characteristics of failure.In these two stress paths,all the marble specimens exhibited strainbursts;however,when the intermediate principal stress was varied,the rockburst became more violent.The obtained results indicate that the intermediate principal stress has a significant effect on rockburst behavior of marble.Under a higher intermediate principal stress before the unloading,more elastic strain energy was accumulated in the specimen,and the cumulative AE energy was higher in the rockburst-induced failure,i.e.,more elastic strain energy was released during the failure.Therefore,more violent failure was observed:more rock fragments with a higher mass and larger size were ejected outward.
基金Project(51869003)supported by the National Natural Science Foundation of ChinaProject(T3030097958)supported by the High Level Innovation Team and Outstanding Scholar Program of Universities in Guagnxi Province,China。
文摘To investigate the acoustic emission(AE)precursors of coarse-grained hard rock instability,an experimental study on the rockburst and slabbing process of granite was carried out using a true triaxial test system.The evolution of the AE signals was monitored and analyzed in terms of the AE hit rate,fractal dimension of the AE hit number,AE count rate,b-value,dominant frequency and microcrack type.The test results show that after rock slabbing occurs,the AE precursors that can be used to predict the final dynamic instability(rockburst)are as follows:indicators such as the AE hit rate and AE count rate suddenly increase and then suddenly decrease;the AE hit rate exhibits a“quiet period”;during the“quiet period”,a small number of high-amplitude and low-frequency hits occur,and the signals corresponding to shear fracture continue to increase.The AE precursors for the final static instability(spalling)are as follows:both the AE hit rate and the b-value continuously decrease,and intermittent sudden increases appear in the high-frequency hits or the AE count rate.
基金Project(50908234)supported by the National Natural Science Foundation of ChinaProject(2017G002-K)supported by the Key Subject of Science and Technology Research and Development Plan of China Railway General Corporation
文摘As a widely distributed geological and engineering material,the soil-rock mixture always undergoes frequentative and short-term freeze-thaw cycles in some regions.Its internal structure is destroyed seriously,but the damage mechanism is not clear.Based on the damage factor,the damage research of properties of soil-rock mixture after different times of freeze-thaw cycles is investigated.Firstly,the size-distributed subgrade gravelly soil samples are prepared and undergo different times of freeze-thaw cycles periodically(0,3,6,10),and indoor large-scale triaxial tests are completed.Secondly,the degradation degree of elastic modulus is considered as a damage factor,and applied to macro damage analysis of soil-rock mixture.Finally,the mesoscopic simulation of the experiments is achieved by PFC3D,and the influence on strength between soil-rock particles caused by freeze-thaw cycles is analyzed.The results show that freeze-thaw cycles cause internal damage of samples by weakening the strength between mesoscopic soil-rock particles,and ultimately affect the macro properties.After freeze-thaw cycles,on the macro-scale,elastic modulus and shear strength of soil-rock mixture both decrease,and the decreasing degree is related to the times of cycles with the mathmatical quadratic form;on the meso-scale,freeze-thaw cycles mainly cause the degradation of the strength between soil-rock particles whose properties are different significantly.
文摘Recycled waste tires when mixed with soil can play an important role as lightweight materials in retaining walls and embankments, machine foundations and railroad track beds in seismic zones. Having high damping characteristic, rubbers can be used as either soil alternative or mixed with soil to reduce vibration when seismic loads are of great concern. Therefore, the objective of this work was to evaluate the dynamic properties of such mixtures prior to practical applications. To this reason, torsional resonant column and dynamic triaxial experiments were carried out and the effect of the important parameters like rubber content and ratio of mean grain size of rubber solids versus soil solids(D50,r/D50,s) on dynamic response of mixtures in a range of low to high shearing strain amplitude from about 4×10-4% to 2.7% were investigated. Considering engineering applications, specimens were prepared almost at the maximum dry density and optimum moisture content to model a mixture layer above the ground water table and in low precipitation region. The results show that tire inclusion significantly reduces the shear modulus and increases the damping ratio of the mixtures. Also decrease in D50,r/D50,s causes the mixture to exhibit more rubber-like behavior. Finally, normalized shear modulus versus shearing strain amplitude curve was proposed for engineering practice.
基金Projects(41672312, 41972294) supported by the National Natural Science Foundation of ChinaProject(2017CFA056) supported by the Outstanding Youth Foundation of Hubei Province, ChinaProject(KFJ170104) supported by the Changsha University of Science & Technology via Open Fund of National Engineering Laboratory of Highway Maintenance Technology, China。
文摘Although the dynamic properties of subgrade soils in seasonally frozen areas have already been studied, few researchers have considered the influence of shallow groundwater during the freeze–thaw(F–T) cycles. So a multifunctional F–T cycle system was developed to imitate the groundwater recharge in the subgrade during the freezing process and a large number of dynamic triaxial experiments were conducted after the F–T cycles. Some significant factors including the F–T cycle number, compaction degree, confining pressure, cyclic deviator stress, loading frequency, and water content were investigated for the resilient modulus of soils. The experimental results indicated that the dynamic resilient modulus of the subgrade was negatively correlated with the cyclic deviator stress, F–T cycle number, and initial water content, whereas the degree of compaction, confining pressure, and loading frequency could enhance the resilient modulus. Furthermore, a modified model considering the F–T cycle number and stress state was established to predict the dynamic resilient modulus. The calculated results of this modified model were very close to the experimental results. Consequently, calculation of the resilient modulus for F–T cycles considering the dynamic load was appropriate. This study provides reference for research focusing on F–T cycles with groundwater supply and the dynamic resilient moduli of subgrade soils in seasonally frozen areas.
基金Projects(51908288,41627801)supported by the National Natural Science Foundation of China。
文摘The state of clean sand was mainly dependent on its void ratio(density)and confining stress that greatly influenced the mechanical behavior(compression,dilatancy and liquefaction)of clean sand.Confirming whether the confining stress was a state variable of sand required precise element tests at different confining stress,especially the tests under very low confining stress whose test data were very limited.In this study,static-dynamic characteristics of clean sand was comprehensively investigated by a unified test program under low and normal confining stress ranging from 5 to 98 kPa,under monotonic/cyclic and drained/undrained conditions,together with the literature available data under confining stress of 1.0 to 3.0 MPa.For monotonic loading tests,the contraction/dilation phase transition was observed for loose sand at low confining stress,and dilatancy angles were stress-dependent.In addition,the liquefaction resistance was observed to increase with reducing of confining stress,and the axial strain varied from compressive to dilative when confining stress increased.Special attention was also paid to the enhancement effect of membrane,and it was observed that its influence on the test results was limited.In addition,the experimental results were proved reliable by reproducibility.
基金Projects(50479057, 50639060) supported by the National Natural Science Foundation of China
文摘An incrementally nonlinear hypoplastic constitutive model was introduced, which was developed without recourse to the concepts in elastoplasticity theory such as yield surface, plastic potential and the decomposition of the deformation into elastic and plastic parts. Triaxial drained tests on rockfill were conducted on a large scale triaxial apparatus under two types of stress paths, which were the stress paths of constant stress ratio and the complex stress paths with transitional features. Motivated by the effect of stress path, the Gudehus-Bauer hypoplastic model was improved by considering the parameter variations with different ratios of stress increment. Fitting parameter a presents a piecewise linear relationship with cosine of the slope angle θ determined by instantaneous stress path. The improved hypoplastic model can present peak stress increasing and volumetric strain changing from dilatancy to contractancy with the increase of transitional confining pressure σ3t and the decrease of slope angle θ of stress path. Compared with the test data, it is shown that the model is capable of fully considering the effect of stress path on rockfill.
基金Project(50908233)supported by the National Natural Science Foundation of ChinaProject(2008G031-Q)supported by National Engineering Laboratory for High Speed Railway Construction,China
文摘By using large scale triaxial shearing apparatus,consolidated-drained shear tests were conducted on coarse-grained soil with different gradations.In order to describe their deformation rules,three main characteristics of tangent Poisson ratio curves were summarized and the reason was revealed by dividing the movement of soil particles into two kinds: the movement of fine particles and the movement of coarse particles.Then,a volumetric strain expression and a tangent Poisson ratio expression were put forward,and two defects of widely used Duncan-Chang model were fixed.Results calculated from them agree well with test results.There are three parameters,namely L,G and F,in this new model.Parameter L reflects the dilatancy of a specimen and L=4 can be used as a criterion to estimate whether a certain kind of soil has dilatancy quality or not.Parameters G and F relate to the initial slope of tangent Poisson ratio curves,and G=F=0 indicates a special situation which happens in dense granular material of the same diameter.Influences of various gradations on volume deformation are mainly reflected in parameter L which is smaller when there are more gravels in specimens.
基金Project(50608038) supported by the National Natural Science Foundation of China
文摘A moisture-content based constitutive model was proposed based on the hyperbolic model as an attempt to move towards the implementation of unsaturated soil mechanics into routine geotechnical engineering practice. The stress-strain behavior of in-situ soil at a depth of 5 m was investigated by conducting undrained triaxial compression tests using the remolded soil samples. The test results show that the stress-strain relationship of unsaturated cohesive soil is still hyperbolic. The values of parameters a and b given in the model decrease with increasing the confining pressure for soil samples with the same moisture content and increase with increasing the moisture content for soil samples under the same confining pressure. The relationships between parameters a, b and moisture content were studied for confining pressures of 100, 150, 200 and 250 kPa. The comparison between the measured and predicted stress-strain curves for an additional group of soil samples, having a moisture content of 25.4%, shows that the proposed moisture content-dependent hyperbolic model provides a good prediction of stress-strain behavior of unsaturated cohesive soil.
基金Project(2011J01308) supported by the Natural Science Foundation of Fujian Province,China
文摘Isotropic consolidation test and consolidated-undrained triaxial test were first undertaken to obtain the parameters of the modified cam-clay(MCC)model and the behavior of natural clayey soil.Then,for the first time,numerical simulation of the two tests was performed by three-dimensional finite element method(FEM)using ABAQUS program.The consolidated-drained triaxial test was also simulated by FEM and compared with theoretical results of MCC model.Especially,the behaviors of MCC model during unloading and reloading were analyzed in detail by FEM.The analysis and comparison indicate that the MCC model is able to accurately describe many features of the mechanical behavior of the soil in isotropic consolidation test and consolidated-drained triaxial test.And the MCC model can well describe the variation of excess pore water pressure with the development of axial strain in consolidated-undrained triaxial test,but its ability to predict the relationship between axial strain and shear stress is relatively poor.The comparison also shows that FEM solutions of the MCC model are basically identical to the theoretical ones.In addition,Mandel-Cryer effect unable to be discovered by the conventional triaxial test in laboratories was disclosed by FEM.The analysis of unloading-reloading by FEM demonstrates that the MCC model disobeys the law of energy conservation under the cyclic loading condition if the elastic shear modulus is linearly pressure-dependent.
