The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research...The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research focus in this technology.They are usually in the form of particles that fill the space between the cathode and anode,and the selection of materials used is important.Carbon-based materials are widely used because of their large specific surface area,good adsorption performance,high chemical stability and low cost.The principles of 3D electrode technology are introduced and recent research on its use for degrading organic pollutants using carbon-based particle electrodes is summarized.The classification of particle electrodes is introduced and the challenges for the future development of carbon-based particle electrodes in wastewater treatment are discussed.展开更多
The particle simulation method is used to study the effects of loading waveforms （i.e. square, sinusoidal and triangle waveforms） on rock damage at mesoscopic scale. Then some influencing factors on rock damage at t...The particle simulation method is used to study the effects of loading waveforms （i.e. square, sinusoidal and triangle waveforms） on rock damage at mesoscopic scale. Then some influencing factors on rock damage at the mesoscopic scale, such as loading frequency, stress amplitude, mean stress, confining pressure and loading sequence, are also investigated with sinusoidal waveform in detail. The related numerical results have demonstrated that： 1） the loading waveform has a certain effect on rock failure processes. The square waveform has the most damage within these waveforms, while the triangle waveform has less damage than sinusoidal waveform. In each cycle, the number of microscopic cracks increases in the loading stage, while it keeps nearly constant in the unloading stage. 2） The loading frequency, stress amplitude, mean stress, confining pressure and loading sequence have considerable effects on rock damage subjected to cyclic loading. The higher the loading frequency, stress amplitude and mean stress, the greater the damage the rock accumulated; in contrast, the lower the confining pressure, the greater the damage the rock has accumulated. 3） There is a threshold value of mean stress and stress amplitude, below which no further damage accumulated after the first few cycle loadings. 4） The high-to-low loading sequence has more damage than the low-to-high loading sequence, suggesting that the rock damage is loading-path dependent.展开更多
The particle simulation method is used to solve free-surface slurry flow problems that may be encountered in several scientific and engineering fields.The main idea behind the use of the particle simulation method is ...The particle simulation method is used to solve free-surface slurry flow problems that may be encountered in several scientific and engineering fields.The main idea behind the use of the particle simulation method is to treat granular or other materials as an assembly of many particles.Compared with the continuum-mechanics-based numerical methods such as the finite element and finite volume methods,the movement of each particle is accurately described in the particle simulation method so that the free surface of a slurry flow problem can be automatically obtained.The major advantage of using the particle simulation method is that only a simple numerical algorithm is needed to solve the governing equation of a particle simulation system.For the purpose of illustrating how to use the particle simulation method to solve free-surface flow problems,three examples involving slurry flow on three different types of river beds have been considered.The related particle simulation results obtained from these three examples have demonstrated that:1) The particle simulation method is a promising and useful method for solving free-surface flow problems encountered in both the scientific and engineering fields;2) The shape and irregular roughness of a river bed can have a significant effect on the free surface morphologies of slurry flow when it passes through the river bed.展开更多
Rapid dewatering and thickening of whole-tailings with ultrafine particles is one of the most important processes for the whole-tailings paste preparation. Deep-cone thickener, a kind of such process for the flocculat...Rapid dewatering and thickening of whole-tailings with ultrafine particles is one of the most important processes for the whole-tailings paste preparation. Deep-cone thickener, a kind of such process for the flocculation and settling of whole-tailings, is particularly necessary to study. However, there exist many problems in observing the flocculation and settling process of whole-tailings, as well as the particle size distribution(PSD) of whole-tailings floccules in deep-cone thickener. Population balance model(PBM) is applied to predict the PSD in deep-cone thickener, and LUO model and GHADIRI model are employed to study the aggregation and fragmentation mechanism of the whole-tailings particles, respectively. Through three-dimensional numerical simulation on the whole-tailings flocculation and settling in deep-cone thickener using computational fluid dynamics(CFD)-PBM, the distribution of density and turbulent kinetic energy in deep-cone thickener were obtained, at the same time the spatio-temporal changes of whole-tailings floccules particle size distribution are analyzed. Finally, the major flocculation position in deep-cone thickener is found and the flocculation settling rules of whole-tailings are achieved.展开更多
The difference of sintering crunodes of metal powders and fibers is discussed. The mathematical model of the surface diffusion described by the difference in mean curvature is defined as a Hamilton-Jacobi-type equatio...The difference of sintering crunodes of metal powders and fibers is discussed. The mathematical model of the surface diffusion described by the difference in mean curvature is defined as a Hamilton-Jacobi-type equation, and the model is numerically solved by the level set method. The three-dimensional numerical simulations of two metal powders and fibers(the fiber angle is 0° or 90°) are implemented by this mathematical model, respectively. The numerical simulation results accord with the experimental ones. The sintering neck growth trends of metal powders and metal fibers are similar. The sintering neck radius of metal fibers is larger than that of metal powders. The difference of the neck radius is caused by the difference of geometric structure which makes an important influence on the curvature affecting the migration rate of atoms.展开更多
Friction stir welding(FSW) is a novel technique for joining different materials without melting. In FSW the welded components are joined by stirring the plasticized material of the welded edges with a special rotating...Friction stir welding(FSW) is a novel technique for joining different materials without melting. In FSW the welded components are joined by stirring the plasticized material of the welded edges with a special rotating pin plunged into the material and moving along the joint line. From the scientific point of view,the key role of the FSW processes belongs to formation of the special plasticized conditions and activation of physical mechanisms of mixing the materials in such conditions to produce the strong homogeneous weld. But it is still a lack of complete understanding of what are these conditions and mechanisms.This paper is devoted to understanding the mechanisms of material mixing in conditions of FSW based on a computer simulation using particles. The movable cellular automaton method(MCA), which is a representative of the particle methods in mechanics of materials, was used to perform all computations.Usually, material flow including material stirring in FSW is simulated using computational fluid mechanics or smoothed particle hydrodynamics, which assume that the material is a continuum and does not take into account the material structure. MCA considers a material as an ensemble of bonded particles. Breaking of inter-particle bonds and formation of new bonds enables simulation of crack nucleation and healing, as well as mass mixing and micro-welding.The paper consists of two main parts. In the first part, the simulations in 2 D statements are performed to study the dynamics of friction stir welding of duralumin plates and influence of different welding regimes on the features of the material stirring and temperature distribution in the forming welded joints. It is shown that the ratio of the rotational speed to the advancing velocity of the tool has a dramatic effect on the joint quality. A suitable choice of these parameters combined with additional ultrasonic impact could considerably reduce the number of pores and microcracks in the weld without significant overheating of the welded materials.The second part of the paper considers simulation in the 3 D statement. These simulations showed that using tool pins of different shape like a cylinder, cone, or pyramid without a shoulder results in negligible motion of the plasticized material in the direction of workpiece thickness. However, the optimal ratio of the advancing velocity to the rotational speed allows transporting of the stirred material around the tool pin several times and hence producing the joint of good quality.展开更多
Based on the analysis of the principles of frequency-phase scanning 3-D （three-dimensional） radar and the scattering mechanism of 3-D radar, the target and clutter IF （intermediate frequency） signals model of freq...Based on the analysis of the principles of frequency-phase scanning 3-D （three-dimensional） radar and the scattering mechanism of 3-D radar, the target and clutter IF （intermediate frequency） signals model of frequencyphase scanning 3-D radar is presented. The IF signals model of different channels of 3-D radar is presented in one simple formula in which complex waveform effects are considered. The simulation results obtained during tests are also provided in the end.展开更多
Probabilistic analysis is a rational approach for engineering design because it provides more insight than traditional deterministic analysis. Probabilistic evaluation on seismic stability of three dimensional (3D) sl...Probabilistic analysis is a rational approach for engineering design because it provides more insight than traditional deterministic analysis. Probabilistic evaluation on seismic stability of three dimensional (3D) slopes is studied in this paper. The slope safety factor is computed by combining the kinematic approach of limit analysis using a three-dimensional rotational failure mechanism with the pseudo-dynamic approach. The variability of input parameters, including six pseudo-dynamic parameters and two soil shear strength parameters, are taken into account by means of Monte-Carlo Simulations (MCS) method. The influences of pseudo-dynamic input variables on the computed failure probabilities are investigated and discussed. It is shown that the obtained failure probabilities increase with the pseudo-dynamic input variables and the pseudo-dynamic approach gives more conservative failure probability estimates compared with the pseudo-static approach.展开更多
A three-dimensional finite element simulation was carried out to investigate the effects of tunnel construction on nearby pile foundation.The displacement controlled model (DCM) was used to simulate the tunneling-indu...A three-dimensional finite element simulation was carried out to investigate the effects of tunnel construction on nearby pile foundation.The displacement controlled model (DCM) was used to simulate the tunneling-induced volume loss effects.The numerical model was verified based on the results of a centrifuge test and a set of parametric studies was implemented based on this model.There is good agreement between the trend of the results of the centrifuge test and the present model.The results of parametric studies show that the tunnelling-induced pile internal force and deformation depend mainly on the pile?tunnel distance,the pile length to tunnel depth ratio and the volume loss.Two different zones are separated by a 45° line projected from the tunnel springline.Within the zone of influence,the pile is subjected to tensile force and large settlement;whereas outside the zone of influence,dragload and small settlement are induced.It is also established that the impact of tunnelling on a pile group is substantially smaller as compared with a single pile in the same location with the rear pile in a group,demonstrating a positive pile group effect.展开更多
To properly simulate hard rock with a high ratio of the uniaxial compressive strength to tensile strength(UCS/TS) and realistic strength-failure envelope,the rock deformation and mechanical characteristics were discus...To properly simulate hard rock with a high ratio of the uniaxial compressive strength to tensile strength(UCS/TS) and realistic strength-failure envelope,the rock deformation and mechanical characteristics were discussed in detail when the particle simulation method with the clump parallel-bond model(CPBM) was used to conduct a series of numerical experiments at the specimen scale.Meanwhile,the effects of the loading procedure and crack density on the mechanical behavior of a specimen,which was modeled by the particle simulation method with the CPBM,were investigated.The related numerical results have demonstrated that:1) The uniaxial compressive strength(UCS),tensile strength(TS) and elastic modulus are overestimated when the conventional loading procedure is used in the particle simulation method with the CPBM; 2) The elastic modulus,strength and UCS/TS decrease,while Poisson ratio increases with the increase of the crack density in the particle simulation method with the CPBM; 3) The particle simulation method with the CPBM can be used to reproduce a high value of UCS/TS(>10),as well as a high friction angle and reasonable cohesion strength; 4) As the confining pressure increases,both the peak strength of the simulated specimen and the number of microscopic cracks increase,but the ratio of tensile cracks number to shear cracks number decreases in the particle simulation method with the CPBM; 5) Compared with the conventional parallel-bond model,the CPBM can be used to reproduce more accurate results for simulating the rock deformation and mechanical characteristics.展开更多
The microscopic characteristics of skeletal particles in rock and soil media have important effects on macroscopic mechanical properties.A mathematical procedure called spherical harmonic function analysis was here de...The microscopic characteristics of skeletal particles in rock and soil media have important effects on macroscopic mechanical properties.A mathematical procedure called spherical harmonic function analysis was here developed to characterize micromorphology of particles and determine the meso effects in a discrete manner.This method has strong mathematical properties with respect to orthogonality and rotating invariance.It was used here to characterize and reconstruct particle micromorphology in three-dimensional space.The applicability and accuracy of the method were assessed through comparison of basic geometric properties such as volume and surface area.The results show that the micromorphological characteristics of reproduced particles become more and more readily distinguishable as the reproduced order number of spherical harmonic function increases,and the error can be brought below 5%when the order number reaches 10.This level of precision is sharp enough to distinguish the characteristics of real particles.Reconstructed particles of the same size but different reconstructed orders were used to form cylindrical samples,and the stress-strain curves of these samples filled with different-order particles which have their mutual morphological features were compared using PFC3D.Results show that the higher the spherical harmonic order of reconstructed particles,the lower the initial compression modulus and the larger the strain at peak intensity.However,peak strength shows only a random relationship to spherical harmonic order.Microstructure reconstruction was here shown to be an efficient means of numerically simulating of multi-scale rock and soil media and studying the mechanical properties of soil samples.展开更多
Proper room and pillar sizes are both critical factors for safe mining and high ore recovery rate in shrinkage stoping mining of underground metal mines.The rock masses of Tangdan copper mine of China are fractured,wh...Proper room and pillar sizes are both critical factors for safe mining and high ore recovery rate in shrinkage stoping mining of underground metal mines.The rock masses of Tangdan copper mine of China are fractured,which needs much reinforcement and support prior to mining.Cement-sodium silicate grout technology was selected,then its related parameters such as grout pressure,diffusion radius and time were calculated and proposed.In order to test the effect of the pressured grout in the fractured No.4 ore block,field experiments were conducted.To optimize stoping configuration,three-dimensional numerical simulation with ANSYS and FLAC 3 D softwares was proposed.The results show that the drilling porosity and mechanical properties of the rock masses are increased obviously.After grout,ore recovery rate is increased by 10.2%employing the newly designed stoping configuration compared with the previous.Last,analyzed from the surface movements,roof subsidence and the maximum principal stress of the pillars,the mining safety is probable of being ensured.展开更多
A user-defined micromechanical model was developed to investigate the fracture mechanism of asphalt concrete （AC） using the discrete element method （DEM）. A three-dimensional （3D） AC beam was built using the ＂F...A user-defined micromechanical model was developed to investigate the fracture mechanism of asphalt concrete （AC） using the discrete element method （DEM）. A three-dimensional （3D） AC beam was built using the ＂Fish＂ language provided by PFC3D and was employed to simulate the three-point bending beam test at two temperature levels： -10 ℃ and 15℃. The AC beam was modeled with the consideration of the microstructural features of asphalt mixtures. Uniaxial complex modulus test and indirect tensile strength test were conducted to obtain material input parameters for numerical modeling. The 3D predictions were validated using laboratory experimental measurements of AC beams prepared by the same mixture design. Effects of mastic stiffness, cohesive and adhesive strength on AC fracture behavior were investigated using the DEM model. The results show that the 3D DEM fracture model can accurately predict the fracture patterns of asphalt concrete. The ratio of stress at interfaces to the stress in mastics increases as the mastic stiffness decreases; however, the increase in the cohesive strength or adhesive strength shows no significant influence on the tensile strength.展开更多
A numerical study is carried out on particle deposition in ducts with either convex or concave wall cavity.Results show that,if compared with smooth duct,particle deposition velocitiesVd^+increase greatly in ducts wit...A numerical study is carried out on particle deposition in ducts with either convex or concave wall cavity.Results show that,if compared with smooth duct,particle deposition velocitiesVd^+increase greatly in ducts with wall cavities.More specifically,forτ+<1,Vd^+increase by about 2–4 orders of magnitude in the cases with the convex and concave wall cavities;forτ+>1,Vd^+grows relatively slower.Enhancement of particle deposition with wall cavities is caused by the following mechanisms,i.e.,interception by the wall cavities,expanded deposition area,and the enhanced flow turbulence.In general,addition of wall cavities is contributive for particle deposition,so it provides an efficient approach to remove particles,especially with small size,e.g.,PM2.5.Moreover,the convex wall cavity leads to a larger increment ofVd^+than the concave wall cavity.However,taking pressure loss into account,thoughVd^+is relatively lower,duct with the concave wall cavity is more efficient than that with the convex wall cavity.展开更多
An economic dispatch problem for power system with wind power is discussed.Using discrete scenario to describe uncertain wind powers,a threshold is given to identify bad scenario set.The bad-scenario-set robust econom...An economic dispatch problem for power system with wind power is discussed.Using discrete scenario to describe uncertain wind powers,a threshold is given to identify bad scenario set.The bad-scenario-set robust economic dispatch model is established to minimize the total penalties on bad scenarios.A specialized hybrid particle swarm optimization(PSO)algorithm is developed through hybridizing simulated annealing(SA)operators.The SA operators are performed according to a scenario-oriented adaptive search rule in a neighborhood which is constructed based on the unit commitment constraints.Finally,an experiment is conducted.The computational results show that the developed algorithm outperforms the existing algorithms.展开更多
A new support vector machine （SVM） optimized by an improved particle swarm optimization （PSO） combined with simulated annealing algorithm （SA） was proposed. By incorporating with the simulated annealing method, ...A new support vector machine （SVM） optimized by an improved particle swarm optimization （PSO） combined with simulated annealing algorithm （SA） was proposed. By incorporating with the simulated annealing method, the global searching capacity of the particle swarm optimization（SAPSO） was enchanced, and the searching capacity of the particle swarm optimization was studied. Then, the improyed particle swarm optimization algorithm was used to optimize the parameters of SVM （c,σ and ε）. Based on the operational data provided by a regional power grid in north China, the method was used in the actual short term load forecasting. The results show that compared to the PSO-SVM and the traditional SVM, the average time of the proposed method in the experimental process reduces by 11.6 s and 31.1 s, and the precision of the proposed method increases by 1.24% and 3.18%, respectively. So, the improved method is better than the PSO-SVM and the traditional SVM.展开更多
To objectively obtain the three-dimensional coordinates of the projectile fuze proximity explosion when projectile intersects the head of missile target, we propose a dynamic seven photoelectric detection screen test ...To objectively obtain the three-dimensional coordinates of the projectile fuze proximity explosion when projectile intersects the head of missile target, we propose a dynamic seven photoelectric detection screen test method, which is made up of six plane detection screens and a flash photoelectric dynamic detection screen. The three-dimensional coordinates calculation model of the projectile proximity explosion position based on seven plane detection screens with dynamic characteristics is established.According to the relation of the dynamic seven photoelectric detection screen planes and the time values,the analytical function of the projectile proximity explosion position parameters under non-linear motion is derived. The projectile signal filtering method based on discrete wavelet transform is explored in this work. Additionally, the projectile signal recognition algorithm using an improved particle swarm is proposed. Based on the characteristics of the time duration and the signal peak error for the projectile passing through the detection screen, the signals attribution of the same projectile passing through six detection screens are analyzed for obtaining precise time values of the same projectile passing through the detection screens. On the basis of the projectile fuze proximity explosion test, the linear motion model and the proposed non-linear motion model are used to calculate and compare the same group of projectiles proximity explosion position parameters. The comparison of test results verifies that the proposed test method and calculation model in this work accurately obtain the actual projectile proximity explosion position parameters.展开更多
Numerical research on the dilute particles movement and deposition characteristics in the vicinity of converging slot-hole(console) was carried out, and the effect of hole shape on the particle deposition characterist...Numerical research on the dilute particles movement and deposition characteristics in the vicinity of converging slot-hole(console) was carried out, and the effect of hole shape on the particle deposition characteristics was investigated. The EI-Batsh deposition model was used to predict the particle deposition characteristics. The results show that the console hole has an obvious advantage in reducing particle deposition in comparison with cylindrical hole, especially under higher blowing ratio. The coolant jet from console holes can cover the wall well. Furthermore, the rotation direction of vortices near console hole is contrary to that near cylindrical hole. For console holes, particle deposition mainly takes place in the upstream area of the holes.展开更多
Natural fragmentation of warheads that detonates causes the casing of the warhead to split into various sized fragments through shear or radial fractures depending on the toughness,density,and grain size of the materi...Natural fragmentation of warheads that detonates causes the casing of the warhead to split into various sized fragments through shear or radial fractures depending on the toughness,density,and grain size of the material.The best known formula for the prediction of the size distribution is the Mott formulae,which is further examined by Grady and Kipp by investigating more carefully the statistical most random way of portioning a given area into a number of entities.We examine the fragmentation behavior of radially expanding steel rings cut from a 25 mm warhead by using an in house smooth particle hydrodynamic(SPH) simulation code called REGULUS.Experimental results were compared with numerical results applying varying particle size and stochastic fracture strain.The numerically obtained number of fragments was consistent with experimental results.Increasing expansion velocity of the rings increases the number of fragments.Statistical variation of the material parameters influences the fragment characteristics,especially for low expansion velocities.A least square regression fit to the cumulative number of fragments by applying a generalized Mott distribution shows that the shape parameter is around 4 for the rings,which is in contrast to the Mott distribution with a shape parameter of 1/2.For initially polar distributed particles,we see signs of a bimodal cumulative fragment distribution.Adding statistical variation in material parameters of the fracture model causes the velocity numerical solutions to become less sensitive to changes in resolution for Cartesian distributed particles.展开更多
In order to evaluate the effects of mesh generation techniques and grid convergence on pump performance in centrifugal pump model, three widely used mesh styles including structured hexahedral, unstructured tetrahedra...In order to evaluate the effects of mesh generation techniques and grid convergence on pump performance in centrifugal pump model, three widely used mesh styles including structured hexahedral, unstructured tetrahedral and hybrid prismatic/tetrahedral meshes were generated for a centrifugal pump model. And quantitative grid convergence was assessed based on a grid convergence index(GCI), which accounts for the degree of grid refinement. The structured, unstructured or hybrid meshes are found to have certain difference for velocity distributions in impeller with the change of grid cell number. And the simulation results have errors to different degrees compared with experimental data. The GCI-value for structured meshes calculated is lower than that for the unstructured and hybrid meshes. Meanwhile, the structured meshes are observed to get more vortexes in impeller passage.Nevertheless, the hybrid meshes are found to have larger low-velocity area at outlet and more secondary vortexes at a specified location than structured meshes and unstructured meshes.展开更多
文摘The use of three-dimensional(3D)electrodes in water treatment is competitive because of their high catalytic efficiency,low energy consumption and promising development.The use of particle electrodes is a key research focus in this technology.They are usually in the form of particles that fill the space between the cathode and anode,and the selection of materials used is important.Carbon-based materials are widely used because of their large specific surface area,good adsorption performance,high chemical stability and low cost.The principles of 3D electrode technology are introduced and recent research on its use for degrading organic pollutants using carbon-based particle electrodes is summarized.The classification of particle electrodes is introduced and the challenges for the future development of carbon-based particle electrodes in wastewater treatment are discussed.
基金Projects(11702235,51641905,41472269) supported by the National Natural Science Foundation of ChinaProject(2017JJ3290) supported by the Natural Science Foundation of Hunan Province,China+1 种基金Project(17C1540) supported by the Scientific Research Foundation of Education Department of Hunan Province,ChinaProject(16GES07) supported by the Open Research Fund of Hunan Key Laboratory of Geomechanics and Engineering Safety,China
文摘The particle simulation method is used to study the effects of loading waveforms （i.e. square, sinusoidal and triangle waveforms） on rock damage at mesoscopic scale. Then some influencing factors on rock damage at the mesoscopic scale, such as loading frequency, stress amplitude, mean stress, confining pressure and loading sequence, are also investigated with sinusoidal waveform in detail. The related numerical results have demonstrated that： 1） the loading waveform has a certain effect on rock failure processes. The square waveform has the most damage within these waveforms, while the triangle waveform has less damage than sinusoidal waveform. In each cycle, the number of microscopic cracks increases in the loading stage, while it keeps nearly constant in the unloading stage. 2） The loading frequency, stress amplitude, mean stress, confining pressure and loading sequence have considerable effects on rock damage subjected to cyclic loading. The higher the loading frequency, stress amplitude and mean stress, the greater the damage the rock accumulated; in contrast, the lower the confining pressure, the greater the damage the rock has accumulated. 3） There is a threshold value of mean stress and stress amplitude, below which no further damage accumulated after the first few cycle loadings. 4） The high-to-low loading sequence has more damage than the low-to-high loading sequence, suggesting that the rock damage is loading-path dependent.
基金Project(11272359)supported by the National Natural Science Foundation of China
文摘The particle simulation method is used to solve free-surface slurry flow problems that may be encountered in several scientific and engineering fields.The main idea behind the use of the particle simulation method is to treat granular or other materials as an assembly of many particles.Compared with the continuum-mechanics-based numerical methods such as the finite element and finite volume methods,the movement of each particle is accurately described in the particle simulation method so that the free surface of a slurry flow problem can be automatically obtained.The major advantage of using the particle simulation method is that only a simple numerical algorithm is needed to solve the governing equation of a particle simulation system.For the purpose of illustrating how to use the particle simulation method to solve free-surface flow problems,three examples involving slurry flow on three different types of river beds have been considered.The related particle simulation results obtained from these three examples have demonstrated that:1) The particle simulation method is a promising and useful method for solving free-surface flow problems encountered in both the scientific and engineering fields;2) The shape and irregular roughness of a river bed can have a significant effect on the free surface morphologies of slurry flow when it passes through the river bed.
基金Project(51174032)supported by the National Natural Science Foundation of ChinaProject(NCET-10-0225)supported by the Program for New Century Excellent Talents in University,ChinaProject(FRF-TP-09-001A)supported by the Fundamental Research Funds for the Central Universities,China
文摘Rapid dewatering and thickening of whole-tailings with ultrafine particles is one of the most important processes for the whole-tailings paste preparation. Deep-cone thickener, a kind of such process for the flocculation and settling of whole-tailings, is particularly necessary to study. However, there exist many problems in observing the flocculation and settling process of whole-tailings, as well as the particle size distribution(PSD) of whole-tailings floccules in deep-cone thickener. Population balance model(PBM) is applied to predict the PSD in deep-cone thickener, and LUO model and GHADIRI model are employed to study the aggregation and fragmentation mechanism of the whole-tailings particles, respectively. Through three-dimensional numerical simulation on the whole-tailings flocculation and settling in deep-cone thickener using computational fluid dynamics(CFD)-PBM, the distribution of density and turbulent kinetic energy in deep-cone thickener were obtained, at the same time the spatio-temporal changes of whole-tailings floccules particle size distribution are analyzed. Finally, the major flocculation position in deep-cone thickener is found and the flocculation settling rules of whole-tailings are achieved.
基金Projects(51174236,51134003)supported by the National Natural Science Foundation of ChinaProject(2011CB606306)supported by the National Basic Research Program of ChinaProject(PMM-SKL-4-2012)supported by the Opening Project of State Key Laboratory of Porous Metal Materials(Northwest Institute for Nonferrous Metal Research),China
文摘The difference of sintering crunodes of metal powders and fibers is discussed. The mathematical model of the surface diffusion described by the difference in mean curvature is defined as a Hamilton-Jacobi-type equation, and the model is numerically solved by the level set method. The three-dimensional numerical simulations of two metal powders and fibers(the fiber angle is 0° or 90°) are implemented by this mathematical model, respectively. The numerical simulation results accord with the experimental ones. The sintering neck growth trends of metal powders and metal fibers are similar. The sintering neck radius of metal fibers is larger than that of metal powders. The difference of the neck radius is caused by the difference of geometric structure which makes an important influence on the curvature affecting the migration rate of atoms.
基金the Russian Fundamental Research Program of the State Academies of Sciencesfor 2013-2020(Priority directionⅢ.23)
文摘Friction stir welding(FSW) is a novel technique for joining different materials without melting. In FSW the welded components are joined by stirring the plasticized material of the welded edges with a special rotating pin plunged into the material and moving along the joint line. From the scientific point of view,the key role of the FSW processes belongs to formation of the special plasticized conditions and activation of physical mechanisms of mixing the materials in such conditions to produce the strong homogeneous weld. But it is still a lack of complete understanding of what are these conditions and mechanisms.This paper is devoted to understanding the mechanisms of material mixing in conditions of FSW based on a computer simulation using particles. The movable cellular automaton method(MCA), which is a representative of the particle methods in mechanics of materials, was used to perform all computations.Usually, material flow including material stirring in FSW is simulated using computational fluid mechanics or smoothed particle hydrodynamics, which assume that the material is a continuum and does not take into account the material structure. MCA considers a material as an ensemble of bonded particles. Breaking of inter-particle bonds and formation of new bonds enables simulation of crack nucleation and healing, as well as mass mixing and micro-welding.The paper consists of two main parts. In the first part, the simulations in 2 D statements are performed to study the dynamics of friction stir welding of duralumin plates and influence of different welding regimes on the features of the material stirring and temperature distribution in the forming welded joints. It is shown that the ratio of the rotational speed to the advancing velocity of the tool has a dramatic effect on the joint quality. A suitable choice of these parameters combined with additional ultrasonic impact could considerably reduce the number of pores and microcracks in the weld without significant overheating of the welded materials.The second part of the paper considers simulation in the 3 D statement. These simulations showed that using tool pins of different shape like a cylinder, cone, or pyramid without a shoulder results in negligible motion of the plasticized material in the direction of workpiece thickness. However, the optimal ratio of the advancing velocity to the rotational speed allows transporting of the stirred material around the tool pin several times and hence producing the joint of good quality.
文摘Based on the analysis of the principles of frequency-phase scanning 3-D （three-dimensional） radar and the scattering mechanism of 3-D radar, the target and clutter IF （intermediate frequency） signals model of frequencyphase scanning 3-D radar is presented. The IF signals model of different channels of 3-D radar is presented in one simple formula in which complex waveform effects are considered. The simulation results obtained during tests are also provided in the end.
文摘Probabilistic analysis is a rational approach for engineering design because it provides more insight than traditional deterministic analysis. Probabilistic evaluation on seismic stability of three dimensional (3D) slopes is studied in this paper. The slope safety factor is computed by combining the kinematic approach of limit analysis using a three-dimensional rotational failure mechanism with the pseudo-dynamic approach. The variability of input parameters, including six pseudo-dynamic parameters and two soil shear strength parameters, are taken into account by means of Monte-Carlo Simulations (MCS) method. The influences of pseudo-dynamic input variables on the computed failure probabilities are investigated and discussed. It is shown that the obtained failure probabilities increase with the pseudo-dynamic input variables and the pseudo-dynamic approach gives more conservative failure probability estimates compared with the pseudo-static approach.
文摘A three-dimensional finite element simulation was carried out to investigate the effects of tunnel construction on nearby pile foundation.The displacement controlled model (DCM) was used to simulate the tunneling-induced volume loss effects.The numerical model was verified based on the results of a centrifuge test and a set of parametric studies was implemented based on this model.There is good agreement between the trend of the results of the centrifuge test and the present model.The results of parametric studies show that the tunnelling-induced pile internal force and deformation depend mainly on the pile?tunnel distance,the pile length to tunnel depth ratio and the volume loss.Two different zones are separated by a 45° line projected from the tunnel springline.Within the zone of influence,the pile is subjected to tensile force and large settlement;whereas outside the zone of influence,dragload and small settlement are induced.It is also established that the impact of tunnelling on a pile group is substantially smaller as compared with a single pile in the same location with the rear pile in a group,demonstrating a positive pile group effect.
基金Project(11272359) supported by the National Natural Science Foundation of China
文摘To properly simulate hard rock with a high ratio of the uniaxial compressive strength to tensile strength(UCS/TS) and realistic strength-failure envelope,the rock deformation and mechanical characteristics were discussed in detail when the particle simulation method with the clump parallel-bond model(CPBM) was used to conduct a series of numerical experiments at the specimen scale.Meanwhile,the effects of the loading procedure and crack density on the mechanical behavior of a specimen,which was modeled by the particle simulation method with the CPBM,were investigated.The related numerical results have demonstrated that:1) The uniaxial compressive strength(UCS),tensile strength(TS) and elastic modulus are overestimated when the conventional loading procedure is used in the particle simulation method with the CPBM; 2) The elastic modulus,strength and UCS/TS decrease,while Poisson ratio increases with the increase of the crack density in the particle simulation method with the CPBM; 3) The particle simulation method with the CPBM can be used to reproduce a high value of UCS/TS(>10),as well as a high friction angle and reasonable cohesion strength; 4) As the confining pressure increases,both the peak strength of the simulated specimen and the number of microscopic cracks increase,but the ratio of tensile cracks number to shear cracks number decreases in the particle simulation method with the CPBM; 5) Compared with the conventional parallel-bond model,the CPBM can be used to reproduce more accurate results for simulating the rock deformation and mechanical characteristics.
基金Project(2015CB057903)supported by the National Basic Research Program of ChinaProjects(51679071,51309089)supported by the National Natural Science Foundation of China+2 种基金Project(BK20130846)supported by the Natural Science Foundation of Jiangsu Province,ChinaProject(2013BAB06B00)supported by the National Key Technology R&D Program,ChinaProject(2015B06014)supported by the Fundamental Research Funds for the Central Universities,China
文摘The microscopic characteristics of skeletal particles in rock and soil media have important effects on macroscopic mechanical properties.A mathematical procedure called spherical harmonic function analysis was here developed to characterize micromorphology of particles and determine the meso effects in a discrete manner.This method has strong mathematical properties with respect to orthogonality and rotating invariance.It was used here to characterize and reconstruct particle micromorphology in three-dimensional space.The applicability and accuracy of the method were assessed through comparison of basic geometric properties such as volume and surface area.The results show that the micromorphological characteristics of reproduced particles become more and more readily distinguishable as the reproduced order number of spherical harmonic function increases,and the error can be brought below 5%when the order number reaches 10.This level of precision is sharp enough to distinguish the characteristics of real particles.Reconstructed particles of the same size but different reconstructed orders were used to form cylindrical samples,and the stress-strain curves of these samples filled with different-order particles which have their mutual morphological features were compared using PFC3D.Results show that the higher the spherical harmonic order of reconstructed particles,the lower the initial compression modulus and the larger the strain at peak intensity.However,peak strength shows only a random relationship to spherical harmonic order.Microstructure reconstruction was here shown to be an efficient means of numerically simulating of multi-scale rock and soil media and studying the mechanical properties of soil samples.
基金Projects(51374034,51674012)supported by the National Natural Science Foundation of ChinaProject(2013BAB02B05)supported by the China National Science and Technology Support Program during the 12th Five-Year Plan Period
文摘Proper room and pillar sizes are both critical factors for safe mining and high ore recovery rate in shrinkage stoping mining of underground metal mines.The rock masses of Tangdan copper mine of China are fractured,which needs much reinforcement and support prior to mining.Cement-sodium silicate grout technology was selected,then its related parameters such as grout pressure,diffusion radius and time were calculated and proposed.In order to test the effect of the pressured grout in the fractured No.4 ore block,field experiments were conducted.To optimize stoping configuration,three-dimensional numerical simulation with ANSYS and FLAC 3 D softwares was proposed.The results show that the drilling porosity and mechanical properties of the rock masses are increased obviously.After grout,ore recovery rate is increased by 10.2%employing the newly designed stoping configuration compared with the previous.Last,analyzed from the surface movements,roof subsidence and the maximum principal stress of the pillars,the mining safety is probable of being ensured.
基金Project(51208178)supported by the National Natural Science Foundation of ChinaProject(2012M520991)supported by China Postdoctoral Science Foundation
文摘A user-defined micromechanical model was developed to investigate the fracture mechanism of asphalt concrete （AC） using the discrete element method （DEM）. A three-dimensional （3D） AC beam was built using the ＂Fish＂ language provided by PFC3D and was employed to simulate the three-point bending beam test at two temperature levels： -10 ℃ and 15℃. The AC beam was modeled with the consideration of the microstructural features of asphalt mixtures. Uniaxial complex modulus test and indirect tensile strength test were conducted to obtain material input parameters for numerical modeling. The 3D predictions were validated using laboratory experimental measurements of AC beams prepared by the same mixture design. Effects of mastic stiffness, cohesive and adhesive strength on AC fracture behavior were investigated using the DEM model. The results show that the 3D DEM fracture model can accurately predict the fracture patterns of asphalt concrete. The ratio of stress at interfaces to the stress in mastics increases as the mastic stiffness decreases; however, the increase in the cohesive strength or adhesive strength shows no significant influence on the tensile strength.
基金Project (51506069) supported by the National Natural Science Foundation of ChinaProject (2016YFB0600605) supported by the National Key Research and Development Program of ChinaProjects (HUST2016YXMS286,HUST2015061) supported by the Fundamental Research Funds for the Central Universities,China
文摘A numerical study is carried out on particle deposition in ducts with either convex or concave wall cavity.Results show that,if compared with smooth duct,particle deposition velocitiesVd^+increase greatly in ducts with wall cavities.More specifically,forτ+<1,Vd^+increase by about 2–4 orders of magnitude in the cases with the convex and concave wall cavities;forτ+>1,Vd^+grows relatively slower.Enhancement of particle deposition with wall cavities is caused by the following mechanisms,i.e.,interception by the wall cavities,expanded deposition area,and the enhanced flow turbulence.In general,addition of wall cavities is contributive for particle deposition,so it provides an efficient approach to remove particles,especially with small size,e.g.,PM2.5.Moreover,the convex wall cavity leads to a larger increment ofVd^+than the concave wall cavity.However,taking pressure loss into account,thoughVd^+is relatively lower,duct with the concave wall cavity is more efficient than that with the convex wall cavity.
基金supported by the National Natural Science Foundation of China(62173219,62073210).
文摘An economic dispatch problem for power system with wind power is discussed.Using discrete scenario to describe uncertain wind powers,a threshold is given to identify bad scenario set.The bad-scenario-set robust economic dispatch model is established to minimize the total penalties on bad scenarios.A specialized hybrid particle swarm optimization(PSO)algorithm is developed through hybridizing simulated annealing(SA)operators.The SA operators are performed according to a scenario-oriented adaptive search rule in a neighborhood which is constructed based on the unit commitment constraints.Finally,an experiment is conducted.The computational results show that the developed algorithm outperforms the existing algorithms.
基金Project(50579101) supported by the National Natural Science Foundation of China
文摘A new support vector machine （SVM） optimized by an improved particle swarm optimization （PSO） combined with simulated annealing algorithm （SA） was proposed. By incorporating with the simulated annealing method, the global searching capacity of the particle swarm optimization（SAPSO） was enchanced, and the searching capacity of the particle swarm optimization was studied. Then, the improyed particle swarm optimization algorithm was used to optimize the parameters of SVM （c,σ and ε）. Based on the operational data provided by a regional power grid in north China, the method was used in the actual short term load forecasting. The results show that compared to the PSO-SVM and the traditional SVM, the average time of the proposed method in the experimental process reduces by 11.6 s and 31.1 s, and the precision of the proposed method increases by 1.24% and 3.18%, respectively. So, the improved method is better than the PSO-SVM and the traditional SVM.
基金supported by Project of the National Natural Science Foundation of China (No.62073256, 61773305)the Key Science and Technology Program of Shaanxi Province (No.2020GY-125)Xi’an Science and Technology Innovation talent service enterprise project (No.2020KJRC0041)。
文摘To objectively obtain the three-dimensional coordinates of the projectile fuze proximity explosion when projectile intersects the head of missile target, we propose a dynamic seven photoelectric detection screen test method, which is made up of six plane detection screens and a flash photoelectric dynamic detection screen. The three-dimensional coordinates calculation model of the projectile proximity explosion position based on seven plane detection screens with dynamic characteristics is established.According to the relation of the dynamic seven photoelectric detection screen planes and the time values,the analytical function of the projectile proximity explosion position parameters under non-linear motion is derived. The projectile signal filtering method based on discrete wavelet transform is explored in this work. Additionally, the projectile signal recognition algorithm using an improved particle swarm is proposed. Based on the characteristics of the time duration and the signal peak error for the projectile passing through the detection screen, the signals attribution of the same projectile passing through six detection screens are analyzed for obtaining precise time values of the same projectile passing through the detection screens. On the basis of the projectile fuze proximity explosion test, the linear motion model and the proposed non-linear motion model are used to calculate and compare the same group of projectiles proximity explosion position parameters. The comparison of test results verifies that the proposed test method and calculation model in this work accurately obtain the actual projectile proximity explosion position parameters.
基金Project(51276090) supported by the National Natural Science Foundation of ChinaProject(CXLX13_166) supported by Funding of Jiangsu Innovation Program for Graduate EducationProject supported by the Fundamental Research Funds for the Central Universities,China
文摘Numerical research on the dilute particles movement and deposition characteristics in the vicinity of converging slot-hole(console) was carried out, and the effect of hole shape on the particle deposition characteristics was investigated. The EI-Batsh deposition model was used to predict the particle deposition characteristics. The results show that the console hole has an obvious advantage in reducing particle deposition in comparison with cylindrical hole, especially under higher blowing ratio. The coolant jet from console holes can cover the wall well. Furthermore, the rotation direction of vortices near console hole is contrary to that near cylindrical hole. For console holes, particle deposition mainly takes place in the upstream area of the holes.
文摘Natural fragmentation of warheads that detonates causes the casing of the warhead to split into various sized fragments through shear or radial fractures depending on the toughness,density,and grain size of the material.The best known formula for the prediction of the size distribution is the Mott formulae,which is further examined by Grady and Kipp by investigating more carefully the statistical most random way of portioning a given area into a number of entities.We examine the fragmentation behavior of radially expanding steel rings cut from a 25 mm warhead by using an in house smooth particle hydrodynamic(SPH) simulation code called REGULUS.Experimental results were compared with numerical results applying varying particle size and stochastic fracture strain.The numerically obtained number of fragments was consistent with experimental results.Increasing expansion velocity of the rings increases the number of fragments.Statistical variation of the material parameters influences the fragment characteristics,especially for low expansion velocities.A least square regression fit to the cumulative number of fragments by applying a generalized Mott distribution shows that the shape parameter is around 4 for the rings,which is in contrast to the Mott distribution with a shape parameter of 1/2.For initially polar distributed particles,we see signs of a bimodal cumulative fragment distribution.Adding statistical variation in material parameters of the fracture model causes the velocity numerical solutions to become less sensitive to changes in resolution for Cartesian distributed particles.
基金Projects(51109095,51179075,51309119)supported by the National Natural Science Foundation of ChinaProject(BE2012131)supported by Science and Technology Support Program of Jiangsu Province,China
文摘In order to evaluate the effects of mesh generation techniques and grid convergence on pump performance in centrifugal pump model, three widely used mesh styles including structured hexahedral, unstructured tetrahedral and hybrid prismatic/tetrahedral meshes were generated for a centrifugal pump model. And quantitative grid convergence was assessed based on a grid convergence index(GCI), which accounts for the degree of grid refinement. The structured, unstructured or hybrid meshes are found to have certain difference for velocity distributions in impeller with the change of grid cell number. And the simulation results have errors to different degrees compared with experimental data. The GCI-value for structured meshes calculated is lower than that for the unstructured and hybrid meshes. Meanwhile, the structured meshes are observed to get more vortexes in impeller passage.Nevertheless, the hybrid meshes are found to have larger low-velocity area at outlet and more secondary vortexes at a specified location than structured meshes and unstructured meshes.
