Changes to the microstructure of a hard carbon(HC)and its solid electrolyte interface(SEI)can be effective in improving the electrode kinetics.However,achieving fast charging using a simple and inexpensive strategy wi...Changes to the microstructure of a hard carbon(HC)and its solid electrolyte interface(SEI)can be effective in improving the electrode kinetics.However,achieving fast charging using a simple and inexpensive strategy without sacrificing its initial Coulombic efficiency remains a challenge in sodium ion batteries.A simple liquid-phase coating approach has been used to generate a pitch-derived soft carbon layer on the HC surface,and its effect on the porosity of HC and SEI chemistry has been studied.A variety of structural characterizations show a soft carbon coating can increase the defect and ultra-micropore contents.The increase in ultra-micropore comes from both the soft carbon coatings and the larger pores within the HC that are partially filled by pitch,which provides more Na+storage sites.In-situ FTIR/EIS and ex-situ XPS showed that the soft carbon coating induced the formation of thinner SEI that is richer in NaF from the electrolyte,which stabilized the interface and promoted the charge transfer process.As a result,the anode produced fastcharging(329.8 mAh g^(−1)at 30 mA g^(−1)and 198.6 mAh g^(−1)at 300 mA g^(−1))and had a better cycling performance(a high capacity retention of 81.4%after 100 cycles at 150 mA g^(−1)).This work reveals the critical role of coating layer in changing the pore structure,SEI chemistry and diffusion kinetics of hard carbon,which enables rational design of sodium-ion battery anode with enhanced fast charging capability.展开更多
As cathode materials for alkali-ion batteries,sodium manganese oxides have been receiving considerable and continuous attention in recent decades.In this work,the structure and environment-dependent stability of NaMn_...As cathode materials for alkali-ion batteries,sodium manganese oxides have been receiving considerable and continuous attention in recent decades.In this work,the structure and environment-dependent stability of NaMn_(2)O_(4) surface were studied based on the first principles calculations.The surface stability diagram of NaMn_(2)O_(4) involving various different terminations of(100),(110)and(111)surfaces was constructed,and the stability of these different terminations could be compared as a function of chemical environment.It is found that the(100)-MnO and(111)-ONa terminations are two more stable terminations under the investigated chemical conditions.And the surface energies of(110)surfaces are negative under the investigated chemical potential,hence,(110)surfaces are unstable.The surface energy of NaMn_(2)O_(4) as a function of O chemical potential is also investigated under constant Na chemical potential.The structure relaxation indicates that the surface rumpling and surface reconstruction can affect the electronic structure of the surface,thereby reducing surface energy and stabilizing the surface.Furthermore,the Wulff shape of NaMn_(2)O_(4) was also constructed based on Gibbs-Wulff theorem.展开更多
A hull structure is prone to local deformation and damage due to the pressure load on the surface.How to simulate surface pressure is an important issue in ship structure test.The loading mode of hydraulic actuator co...A hull structure is prone to local deformation and damage due to the pressure load on the surface.How to simulate surface pressure is an important issue in ship structure test.The loading mode of hydraulic actuator combined with high-pressure flexible bladder was proposed,and the numerical model of the loading device based on flexible bladder was established.The design and analysis method of high-pressure flexible bladder based on aramid-fiber reinforced thermoplastic polyurethane was proposed to break through the surface pressure loading technology of ship structures.The surface pressure loading system based on flexible bladder was developed.The ultimate strength verification test of the box girder under the combined action of bending moment and pressure was carried out to systematically verify the feasibility and applicability of the loading system.The results show that the surface pressure loading technology can be used well for applying uniform pressure to ship structures.Compared with the traditional surface loading methods,the improved device can be applied with horizontal constant pressure load,with rapid response and safe process,and the pressure load is always stable with the increase of the bending moment load during the test.The requirement for uniform loading in the comprehensive strength test of large structural models is satisfied and the accuracy of the test results is improved by this system.展开更多
Secondary electron emission(SEE)has emerged as a critical issue in next-generation accelerators.Mitigating SEE on metal surfaces is crucial for enhancing the stability and emittance of particle accelerators while exte...Secondary electron emission(SEE)has emerged as a critical issue in next-generation accelerators.Mitigating SEE on metal surfaces is crucial for enhancing the stability and emittance of particle accelerators while extending their lifespan.This paper explores the application of laser-assisted water jet technology in constructing high-quality micro-trap structures on 316L stainless steel,a key material in accelerator manufacturing.The study systematically analyzes the impact of various parameters such as laser repetition frequency,pulse duration,average power,water jet pressure,repeat times,nozzle offset,focal position,offset distance between grooves,and processing speed on the surface morphology of stainless steel.The findings reveal that micro-groove depth increases with higher laser power but decreases with increasing water jet pressure and processing speed.Interestingly,repeat times have minimal effect on depth.On the other hand,micro-groove width increases with higher laser power and repeat times but decreases with processing speed.By optimizing these parameters,the researchers achieved high-quality pound sign-shaped trap structure with consistent dimensions.We tested the secondary electron emission coefficient of the"well"structure.The coefficient is reduced by 0.5 at most compared to before processing,effectively suppressing secondary electron emission.These results offer indispensable insights for the fabrication of micro-trap structures on material surfaces.Laser-assisted water jet technology demonstrates considerable potential in mitigating SEE on metal surfaces.展开更多
We assembled approximately 328 seismic records. The data set was from 4 digitally recording long-period and broadband stations of CDSN. We carried out the inversion based on the partitioned waveform inversion (PWI). I...We assembled approximately 328 seismic records. The data set was from 4 digitally recording long-period and broadband stations of CDSN. We carried out the inversion based on the partitioned waveform inversion (PWI). It partitions the large-scale optimization problem into a number of independent small-scale problems. We adopted surface waveform inversion with an equal block (2((2() discretization in order to acquire the images of shear velocity structure at different depths (from surface to 430 km) in the crust and upper-mantle. The resolution of all these anomalies has been established with (check-board( resolution tests. These results show significant difference in velocity, lithosphere and asthenosphere structure between South China Sea and its adjacent regions.展开更多
Paint removal from steel structure is executed for shipyards of marine and offshore engineering.Due to environmental unfriendliness and unhealthy drawbacks of sand blasting technique, laser ablation technique is propo...Paint removal from steel structure is executed for shipyards of marine and offshore engineering.Due to environmental unfriendliness and unhealthy drawbacks of sand blasting technique, laser ablation technique is proposed as a substituting method.By absorbing high energy of the 1064 nm pulsed laser, the paint is vaporized quickly.The ablated debris is then collected by using a suction pump.Initial metal surface of the steel is exposed when laser beam irradiates perpendicularly and scans over it.The cleaned surface fulfills the requirements of surface preparation standards ISO 8501 of SA2.The adhesion is further characterized with pull-off test after carrying out painting with Jotamastic 87 aluminum paint.The repainting can be embedded onto the laser cleaned surface to bond much more tightly.The excellent adhesion strength of 20 MPa between repainted coating and the substrate is achieved, which is higher than what is required by shipyards applications.展开更多
The characteristics of surface maneuver targets are analyzed and a 3-D relative motion model for missiles and targets is established. A variable structure guidance law is designed considering the characteristics of ta...The characteristics of surface maneuver targets are analyzed and a 3-D relative motion model for missiles and targets is established. A variable structure guidance law is designed considering the characteristics of targets. In the guidance law, the distance between missiles and targets as well as the missile-target relative velocity are all substituted by estimation values. The estimation errors, the target＇s velocity, and the maneuver acceleration are all treated as bounded disturbance. The guidance law proposed can be implemented conveniently in engineering with little target information. The performance of the guidance system is analyzed theoretically and the numerical simulation result shows the effectiveness of the guidance law.展开更多
In order to acquire the dynamic characteristics of joint surfaces of complex assembled structures, a novel parameter identification technique was adopted. Virtual materials were introduced to simulate the stiffness an...In order to acquire the dynamic characteristics of joint surfaces of complex assembled structures, a novel parameter identification technique was adopted. Virtual materials were introduced to simulate the stiffness and damping features of the joint surfaces between two different structures. Properties of the virtual materials, including elasticity modulus, density, and Poisson ratio, were gradually modified. At last, FEM modal results of the assembled structures are consistent with the experimental ones. This proves the feasibility of the simulating method and paves a solid foundation of the further research of the dynamic simulation.展开更多
The binding energies of ethylene oxide (Et-O) adsorbed on Cu(110) surface for different adsorption sites and orientations are calculated with an atom superposition and electron delocalization molecular orbital (ASED-M...The binding energies of ethylene oxide (Et-O) adsorbed on Cu(110) surface for different adsorption sites and orientations are calculated with an atom superposition and electron delocalization molecular orbital (ASED-MO) using cluster models. It shows that the top site of Cu(110) surface is preferable for Et-O adsorption and the orientation of C-C bond of Et-O is parallel to the [110] direction of the substratc. The distance of an oxygen of Et-O to the Cu atom is approximately 1.5817(?). It is different from the supposition of C. Benndorf et al., in which the oxygen was proposed on the short bridge site with C-C bond orientating to [110] direction of Cu(110)展开更多
The surface structure and properties are different from those of the bulk, depending on the substrate materials and deposition condition, and playing an important role in precise optical components. The conventional s...The surface structure and properties are different from those of the bulk, depending on the substrate materials and deposition condition, and playing an important role in precise optical components. The conventional spectroscopic methods to monitor the surface structure are restricted only in several layers of molecules. It is known that the penetration depth of the incident light increases with its wavelength and decreases with the angle of incidence. Thus infrared spectroscopy provides a powerful means for determination of surface structure and the depth profile up to micrometers. By recording the reflection spectra at different angles of incidence, the surface structure and its depth profile can be monitored successively. Further, the incident field has the subcomponents parallel and perpendicular to the surface, which excite the transverse and longitudinal optic modes, respectively. Change of the polarization direction of the incident light provides a practical function to study anisotropic property of the surface and the interaction between the transverse and longitudinal optic modes. In this work, infrared spectrophotometer was applied to investigate the depth profile in microstructure of silica glass. Combining with the glass fiber system, this technique can be used for in-situ control of the deposition process. In comparing with ellipsometry, this method reveals both structural and constitutional information.展开更多
In order to further investigate the surface flashover mechanism in vacuum, the surface flashover and electric field distribution of multilayer organic insulation structure are studied and developed based on the previo...In order to further investigate the surface flashover mechanism in vacuum, the surface flashover and electric field distribution of multilayer organic insulation structure are studied and developed based on the previous studies. The samples of multilayer organic insulation structure are prepared by inserting multilayer organic composite material with different relative permittivity between the electrode and the dielectric. Two multilayer organic insulation structures are prepared in this study. One is the cylindrical samples, the other is 45° samples. The impulse (1.2/50 μs) and DC flashover voltages in vacuum are tested, and the electric field distributions of two insulation structures are analyzed by ANSYS. It is found that these two insulation structure could effectively improve the surface flashover performance in vacuum. The results indicate that the highest impulse first flashover voltage of cylindrical samples reaches 65 kV and increases by 25% under im- pulse voltage. The highest first flashover voltage of /c samples reaches 81 kV and increases by 32% under impulse voltage. The results of electric field simulation demonstrate that different mechanisms exist between 45° insulation structure and cylindrical structure.展开更多
The response surface method(RSM) is one of the main approaches for analyzing reliability problems with implicit performance functions.An improved adaptive RSM based on uniform design(UD) and double weighted regression...The response surface method(RSM) is one of the main approaches for analyzing reliability problems with implicit performance functions.An improved adaptive RSM based on uniform design(UD) and double weighted regression(DWR) was presented.In the proposed method,the basic principle of the iteratively adaptive response surface method is applied.Uniform design is used to sample the fitting points.And a double weighted regression system considering the distances from the fitting points to the limit state surface and to the estimated design points is set to determine the coefficients of the response surface model.Compared with the conventional approaches,the fitting points selected by UD are more representative,and a better approximation in the key region is also observed with DWR.Numerical examples show that the proposed method has good convergent capability and computational accuracy.展开更多
There are two mechanisms of the coarse surface asperity resistance effect and rubbing resistance effect in the course of the soft rock structural surface creep,of which the former plays a dominant role in hindering th...There are two mechanisms of the coarse surface asperity resistance effect and rubbing resistance effect in the course of the soft rock structural surface creep,of which the former plays a dominant role in hindering the deformation in the starting creep phase,so that the structural surface creep usually displays the strong surface roughness effect,and so does the latter when the asperities in the coarse surface were fractured by shearing.Under the low stress condition,there are only two phases of the decelerating creep and the constant creep for the soft rock structural surface,and as the stress increases and overcomes the rubbing resistance,the accelerating creep failure of the structural surface will happen suddenly.Therefore,a multiple rheological model,which combines the nonlinear NEWTON body(NN) of a certain mass and the empirical plastic body(EM) with the classical SAINT VENANT body,NEWTON body,KELVIN body and HOOKE body,could be used to comprehensively describe the creep characteristics of the soft rock structural surface.Its mechanical parameter values will vary owing to the different surface roughness of the structural surface.The parameters of GH,GK and ηL are positively linearly correlative to the surface roughness.The surface roughness and m are negative exponential function correlation.The long-term strength τS is positively correlative to the surface roughness.展开更多
In this note,we study the Yang-Mills bar connection,i.e.,the curvature of obeys,δ_(A)^(*)F_(A)^(0.2)on a principal G-bundle P over a compact complex manifold.According to the Koszul-Malgrange criterion,any holomorphi...In this note,we study the Yang-Mills bar connection,i.e.,the curvature of obeys,δ_(A)^(*)F_(A)^(0.2)on a principal G-bundle P over a compact complex manifold.According to the Koszul-Malgrange criterion,any holomorphic structure on can be seen as a solution to this equation.Suppose that G=SU(2)or SO(3)and X is a complex surface with H_(1)(X,Z_(2))=0.We then prove that the-part curvature of an irreducible Yang-Mills bar connection vanishes,i.e.,(P,δ_(A))is holomorphic.展开更多
The novelty of this research lies in the successful fabrication of a 3D-printed honeycomb structure filled with nanofillers for acoustic properties,utilizing an impedance tube setup in accordance with ASTM standard E ...The novelty of this research lies in the successful fabrication of a 3D-printed honeycomb structure filled with nanofillers for acoustic properties,utilizing an impedance tube setup in accordance with ASTM standard E 1050-12.The Creality Ender-3,a 3D printer,was used for printing the honeycomb structures,and polylactic acid(PLA)material was employed for their construction.The organic,inorganic,and polymeric compounds within the composites were identified using fourier transformation infrared(FTIR)spectroscopy.The structure and homogeneity of the samples were examined using a field emission scanning electron microscope(FESEM).To determine the sound absorption coefficient of the 3D printed honeycomb structure,numerous samples were systematically developed using central composite design(CCD)and analysed using response surface methodology(RSM).The RSM mathematical model was established to predict the optimum values of each factor and noise reduction coefficient(NRC).The optimum values for an NRC of 0.377 were found to be 1.116 wt% carbon black,1.025 wt% aluminium powder,and 3.151 mm distance between parallel edges.Overall,the results demonstrate that a 3Dprinted honeycomb structure filled with nanofillers is an excellent material that can be utilized in various fields,including defence and aviation,where lightweight and acoustic properties are of great importance.展开更多
An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the ma...An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the main stress trajectories as the representation of force flows on a free-form surface,an automatic grid generation approach is proposed for the architectural design.The algorithm automatically plots the main stress trajectories on a 3D free-form surface,and adopts a modified advancing front meshing technique to generate the structural grid.Based on the proposed algorithm,an automatic grid generator named "St-Surmesh" is developed for the practical architectural design of free-form surface structure.The surface geometry of one of the Sun Valleys in Expo Axis for the Expo Shanghai 2010 is selected as a numerical example for validating the proposed approach.Comparative studies are performed to demonstrate how different structural grids affect the design of a free-form surface structure.展开更多
Ablation threshold is an important concept in the study of femtosecond laser micro-and nano-machining.In this paper,the ablation experiments of three kinds of surface roughness 4H-Si C substrates irradiated by femtose...Ablation threshold is an important concept in the study of femtosecond laser micro-and nano-machining.In this paper,the ablation experiments of three kinds of surface roughness 4H-Si C substrates irradiated by femtosecond laser were carried out.The feature thresholds were systematically measured for three surface roughness Si C substrates and found in the modification and annealing regions ranging from coincidence(R_(a)=0.5 nm)to a clear demarcation(R_(a)=5.5 nm),eventually being difficult to identify the presence of the former(R_(a)=89 nm).Under multi-pulse laser irradiation,oriented ripple structures were generated in the annealing region,where deep subwavelength ripples(about 110 nm,Λ≈0.2λ)can be generated above substrates with surface roughness higher than 5.5 nm.We investigated the effect of surface roughness on the ablation morphology,ablation threshold,and periodic structures of femtosecond laser ablation of 4H-Si C substrates,while the ablation threshold was tended to decrease and stabilize with the increase of pulse number N≥500.展开更多
In order to optimize the crashworthy characteristic of energy-absorbing structures, the surrogate models of specific energy absorption （SEA） and ratio of SEA to initial peak force （REAF） with respect to the design...In order to optimize the crashworthy characteristic of energy-absorbing structures, the surrogate models of specific energy absorption （SEA） and ratio of SEA to initial peak force （REAF） with respect to the design parameters were respectively constructed based on surrogate model optimization methods （polynomial response surface method （PRSM） and Kriging method （KM））. Firstly, the sample data were prepared through the design of experiment （DOE）. Then, the test data models were set up based on the theory of surrogate model, and the data samples were trained to obtain the response relationship between the SEA ＆amp; REAF and design parameters. At last, the structure optimal parameters were obtained by visual analysis and genetic algorithm （GA）. The results indicate that the KM, where the local interpolation method is used in Gauss correlation function, has the highest fitting accuracy and the structure optimal parameters are obtained as： the SEA of 29.8558 kJ/kg （corresponding toa=70 mm andt= 3.5 mm） and REAF of 0.2896 （corresponding toa=70 mm andt=1.9615 mm）. The basis function of the quartic PRSM with higher order than that of the quadratic PRSM, and the mutual influence of the design variables are considered, so the fitting accuracy of the quartic PRSM is higher than that of the quadratic PRSM.展开更多
The fatigue life of aeroengine turbine disc presents great dispersion due to the randomness of the basic variables,such as applied load,working temperature,geometrical dimensions and material properties.In order to am...The fatigue life of aeroengine turbine disc presents great dispersion due to the randomness of the basic variables,such as applied load,working temperature,geometrical dimensions and material properties.In order to ameliorate reliability analysis efficiency without loss of reliability,the distributed collaborative response surface method(DCRSM) was proposed,and its basic theories were established in this work.Considering the failure dependency among the failure modes,the distributed response surface was constructed to establish the relationship between the failure mode and the relevant random variables.Then,the failure modes were considered as the random variables of system response to obtain the distributed collaborative response surface model based on structure failure criterion.Finally,the given turbine disc structure was employed to illustrate the feasibility and validity of the presented method.Through the comparison of DCRSM,Monte Carlo method(MCM) and the traditional response surface method(RSM),the results show that the computational precision for DCRSM is more consistent with MCM than RSM,while DCRSM needs far less computing time than MCM and RSM under the same simulation conditions.Thus,DCRSM is demonstrated to be a feasible and valid approach for improving the computational efficiency of reliability analysis for aeroengine turbine disc fatigue life with multiple random variables,and has great potential value for the complicated mechanical structure with multi-component and multi-failure mode.展开更多
Despite being a promising photoanode material for water splitting,WO_(3) has low conductivity,high onset potential,and sluggish water oxidation kinetics.In this study,we designed Ti-doped WO_(3) nanoplate arrays on fl...Despite being a promising photoanode material for water splitting,WO_(3) has low conductivity,high onset potential,and sluggish water oxidation kinetics.In this study,we designed Ti-doped WO_(3) nanoplate arrays on fluoride-doped tin oxide by a seed-free hydrothermal method,and the effects of doping on the photoelectrochemical performance were investigated.The optimal Ti-doped WO_(3) electrode achieved a photocurrent density of 0.53 mA/cm^(2) at 0.6 V(vs Ag/AgCl),110%higher than that of pure WO_(3) nanoplate arrays.Moreover,a significant cathodic shift in the onset potential was observed after doping.X-ray photoelectron spectroscopy valence band and ultraviolet–visible spectra revealed that the band positions of Ti-doped WO_(3) photoanodes moved upward,yielding a lower onset potential.Furthermore,electrochemical impedance spectroscopy measurements revealed that the conductivities of the WO_(3) photoanodes improved after doping,because of the rapid separation of photo-generated charge carriers.Thus,we report a new design route toward efficient and low-cost photoanodes for photoelectrochemical applications.展开更多
基金National Key Research and Development Program of China(2022YFE0206300)National Natural Science Foundation of China(U21A2081,22075074,22209047)+2 种基金Guangdong Basic and Applied Basic Research Foundation(2024A1515011620)Hunan Provincial Natural Science Foundation of China(2024JJ5068)Foundation of Yuelushan Center for Industrial Innovation(2023YCII0119)。
文摘Changes to the microstructure of a hard carbon(HC)and its solid electrolyte interface(SEI)can be effective in improving the electrode kinetics.However,achieving fast charging using a simple and inexpensive strategy without sacrificing its initial Coulombic efficiency remains a challenge in sodium ion batteries.A simple liquid-phase coating approach has been used to generate a pitch-derived soft carbon layer on the HC surface,and its effect on the porosity of HC and SEI chemistry has been studied.A variety of structural characterizations show a soft carbon coating can increase the defect and ultra-micropore contents.The increase in ultra-micropore comes from both the soft carbon coatings and the larger pores within the HC that are partially filled by pitch,which provides more Na+storage sites.In-situ FTIR/EIS and ex-situ XPS showed that the soft carbon coating induced the formation of thinner SEI that is richer in NaF from the electrolyte,which stabilized the interface and promoted the charge transfer process.As a result,the anode produced fastcharging(329.8 mAh g^(−1)at 30 mA g^(−1)and 198.6 mAh g^(−1)at 300 mA g^(−1))and had a better cycling performance(a high capacity retention of 81.4%after 100 cycles at 150 mA g^(−1)).This work reveals the critical role of coating layer in changing the pore structure,SEI chemistry and diffusion kinetics of hard carbon,which enables rational design of sodium-ion battery anode with enhanced fast charging capability.
基金Project(BK20241969)supported by the Natural Science Foundation of Jiangsu Province,ChinaProject(51971249)supported by the National Natural Science Foundation of China。
文摘As cathode materials for alkali-ion batteries,sodium manganese oxides have been receiving considerable and continuous attention in recent decades.In this work,the structure and environment-dependent stability of NaMn_(2)O_(4) surface were studied based on the first principles calculations.The surface stability diagram of NaMn_(2)O_(4) involving various different terminations of(100),(110)and(111)surfaces was constructed,and the stability of these different terminations could be compared as a function of chemical environment.It is found that the(100)-MnO and(111)-ONa terminations are two more stable terminations under the investigated chemical conditions.And the surface energies of(110)surfaces are negative under the investigated chemical potential,hence,(110)surfaces are unstable.The surface energy of NaMn_(2)O_(4) as a function of O chemical potential is also investigated under constant Na chemical potential.The structure relaxation indicates that the surface rumpling and surface reconstruction can affect the electronic structure of the surface,thereby reducing surface energy and stabilizing the surface.Furthermore,the Wulff shape of NaMn_(2)O_(4) was also constructed based on Gibbs-Wulff theorem.
文摘A hull structure is prone to local deformation and damage due to the pressure load on the surface.How to simulate surface pressure is an important issue in ship structure test.The loading mode of hydraulic actuator combined with high-pressure flexible bladder was proposed,and the numerical model of the loading device based on flexible bladder was established.The design and analysis method of high-pressure flexible bladder based on aramid-fiber reinforced thermoplastic polyurethane was proposed to break through the surface pressure loading technology of ship structures.The surface pressure loading system based on flexible bladder was developed.The ultimate strength verification test of the box girder under the combined action of bending moment and pressure was carried out to systematically verify the feasibility and applicability of the loading system.The results show that the surface pressure loading technology can be used well for applying uniform pressure to ship structures.Compared with the traditional surface loading methods,the improved device can be applied with horizontal constant pressure load,with rapid response and safe process,and the pressure load is always stable with the increase of the bending moment load during the test.The requirement for uniform loading in the comprehensive strength test of large structural models is satisfied and the accuracy of the test results is improved by this system.
文摘Secondary electron emission(SEE)has emerged as a critical issue in next-generation accelerators.Mitigating SEE on metal surfaces is crucial for enhancing the stability and emittance of particle accelerators while extending their lifespan.This paper explores the application of laser-assisted water jet technology in constructing high-quality micro-trap structures on 316L stainless steel,a key material in accelerator manufacturing.The study systematically analyzes the impact of various parameters such as laser repetition frequency,pulse duration,average power,water jet pressure,repeat times,nozzle offset,focal position,offset distance between grooves,and processing speed on the surface morphology of stainless steel.The findings reveal that micro-groove depth increases with higher laser power but decreases with increasing water jet pressure and processing speed.Interestingly,repeat times have minimal effect on depth.On the other hand,micro-groove width increases with higher laser power and repeat times but decreases with processing speed.By optimizing these parameters,the researchers achieved high-quality pound sign-shaped trap structure with consistent dimensions.We tested the secondary electron emission coefficient of the"well"structure.The coefficient is reduced by 0.5 at most compared to before processing,effectively suppressing secondary electron emission.These results offer indispensable insights for the fabrication of micro-trap structures on material surfaces.Laser-assisted water jet technology demonstrates considerable potential in mitigating SEE on metal surfaces.
基金State Natural Scientific Foundation (49734150) and National High Performance Computation Foundation.
文摘We assembled approximately 328 seismic records. The data set was from 4 digitally recording long-period and broadband stations of CDSN. We carried out the inversion based on the partitioned waveform inversion (PWI). It partitions the large-scale optimization problem into a number of independent small-scale problems. We adopted surface waveform inversion with an equal block (2((2() discretization in order to acquire the images of shear velocity structure at different depths (from surface to 430 km) in the crust and upper-mantle. The resolution of all these anomalies has been established with (check-board( resolution tests. These results show significant difference in velocity, lithosphere and asthenosphere structure between South China Sea and its adjacent regions.
基金supported by the National Natural Science Foundation of China (U1609209)National Natural Science Foundation of China (61605162)+2 种基金NSFC-Liaoning Province united foundation (U1608259)National Natural Science Foundation of China (51501219)the financial support from the China Scholarship Council
文摘Paint removal from steel structure is executed for shipyards of marine and offshore engineering.Due to environmental unfriendliness and unhealthy drawbacks of sand blasting technique, laser ablation technique is proposed as a substituting method.By absorbing high energy of the 1064 nm pulsed laser, the paint is vaporized quickly.The ablated debris is then collected by using a suction pump.Initial metal surface of the steel is exposed when laser beam irradiates perpendicularly and scans over it.The cleaned surface fulfills the requirements of surface preparation standards ISO 8501 of SA2.The adhesion is further characterized with pull-off test after carrying out painting with Jotamastic 87 aluminum paint.The repainting can be embedded onto the laser cleaned surface to bond much more tightly.The excellent adhesion strength of 20 MPa between repainted coating and the substrate is achieved, which is higher than what is required by shipyards applications.
文摘The characteristics of surface maneuver targets are analyzed and a 3-D relative motion model for missiles and targets is established. A variable structure guidance law is designed considering the characteristics of targets. In the guidance law, the distance between missiles and targets as well as the missile-target relative velocity are all substituted by estimation values. The estimation errors, the target＇s velocity, and the maneuver acceleration are all treated as bounded disturbance. The guidance law proposed can be implemented conveniently in engineering with little target information. The performance of the guidance system is analyzed theoretically and the numerical simulation result shows the effectiveness of the guidance law.
文摘In order to acquire the dynamic characteristics of joint surfaces of complex assembled structures, a novel parameter identification technique was adopted. Virtual materials were introduced to simulate the stiffness and damping features of the joint surfaces between two different structures. Properties of the virtual materials, including elasticity modulus, density, and Poisson ratio, were gradually modified. At last, FEM modal results of the assembled structures are consistent with the experimental ones. This proves the feasibility of the simulating method and paves a solid foundation of the further research of the dynamic simulation.
文摘The binding energies of ethylene oxide (Et-O) adsorbed on Cu(110) surface for different adsorption sites and orientations are calculated with an atom superposition and electron delocalization molecular orbital (ASED-MO) using cluster models. It shows that the top site of Cu(110) surface is preferable for Et-O adsorption and the orientation of C-C bond of Et-O is parallel to the [110] direction of the substratc. The distance of an oxygen of Et-O to the Cu atom is approximately 1.5817(?). It is different from the supposition of C. Benndorf et al., in which the oxygen was proposed on the short bridge site with C-C bond orientating to [110] direction of Cu(110)
基金This work was supported by the Cheung Kong Scholars Program and the National High Technology Research and Development(863)Program of China.
文摘The surface structure and properties are different from those of the bulk, depending on the substrate materials and deposition condition, and playing an important role in precise optical components. The conventional spectroscopic methods to monitor the surface structure are restricted only in several layers of molecules. It is known that the penetration depth of the incident light increases with its wavelength and decreases with the angle of incidence. Thus infrared spectroscopy provides a powerful means for determination of surface structure and the depth profile up to micrometers. By recording the reflection spectra at different angles of incidence, the surface structure and its depth profile can be monitored successively. Further, the incident field has the subcomponents parallel and perpendicular to the surface, which excite the transverse and longitudinal optic modes, respectively. Change of the polarization direction of the incident light provides a practical function to study anisotropic property of the surface and the interaction between the transverse and longitudinal optic modes. In this work, infrared spectrophotometer was applied to investigate the depth profile in microstructure of silica glass. Combining with the glass fiber system, this technique can be used for in-situ control of the deposition process. In comparing with ellipsometry, this method reveals both structural and constitutional information.
基金Project supported by National Science Fund for Outstanding Young Scholars of China (50625721)National Basic Research Program of China (973 Program) (2011CB 209404)
文摘In order to further investigate the surface flashover mechanism in vacuum, the surface flashover and electric field distribution of multilayer organic insulation structure are studied and developed based on the previous studies. The samples of multilayer organic insulation structure are prepared by inserting multilayer organic composite material with different relative permittivity between the electrode and the dielectric. Two multilayer organic insulation structures are prepared in this study. One is the cylindrical samples, the other is 45° samples. The impulse (1.2/50 μs) and DC flashover voltages in vacuum are tested, and the electric field distributions of two insulation structures are analyzed by ANSYS. It is found that these two insulation structure could effectively improve the surface flashover performance in vacuum. The results indicate that the highest impulse first flashover voltage of cylindrical samples reaches 65 kV and increases by 25% under im- pulse voltage. The highest first flashover voltage of /c samples reaches 81 kV and increases by 32% under impulse voltage. The results of electric field simulation demonstrate that different mechanisms exist between 45° insulation structure and cylindrical structure.
基金Project(50774095) supported by the National Natural Science Foundation of ChinaProject(200449) supported by National Outstanding Doctoral Dissertations Special Funds of China
文摘The response surface method(RSM) is one of the main approaches for analyzing reliability problems with implicit performance functions.An improved adaptive RSM based on uniform design(UD) and double weighted regression(DWR) was presented.In the proposed method,the basic principle of the iteratively adaptive response surface method is applied.Uniform design is used to sample the fitting points.And a double weighted regression system considering the distances from the fitting points to the limit state surface and to the estimated design points is set to determine the coefficients of the response surface model.Compared with the conventional approaches,the fitting points selected by UD are more representative,and a better approximation in the key region is also observed with DWR.Numerical examples show that the proposed method has good convergent capability and computational accuracy.
基金Projects(50774093,50490274) supported by the National Natural Science Foundation of China
文摘There are two mechanisms of the coarse surface asperity resistance effect and rubbing resistance effect in the course of the soft rock structural surface creep,of which the former plays a dominant role in hindering the deformation in the starting creep phase,so that the structural surface creep usually displays the strong surface roughness effect,and so does the latter when the asperities in the coarse surface were fractured by shearing.Under the low stress condition,there are only two phases of the decelerating creep and the constant creep for the soft rock structural surface,and as the stress increases and overcomes the rubbing resistance,the accelerating creep failure of the structural surface will happen suddenly.Therefore,a multiple rheological model,which combines the nonlinear NEWTON body(NN) of a certain mass and the empirical plastic body(EM) with the classical SAINT VENANT body,NEWTON body,KELVIN body and HOOKE body,could be used to comprehensively describe the creep characteristics of the soft rock structural surface.Its mechanical parameter values will vary owing to the different surface roughness of the structural surface.The parameters of GH,GK and ηL are positively linearly correlative to the surface roughness.The surface roughness and m are negative exponential function correlation.The long-term strength τS is positively correlative to the surface roughness.
基金supported by the National Natural Science Foundation of China(12271496)the Youth Innovation Promotion Association CAS,the Fundamental Research Funds of the Central Universities,and the USTC Research Funds of the Double First-Class Initiative.
文摘In this note,we study the Yang-Mills bar connection,i.e.,the curvature of obeys,δ_(A)^(*)F_(A)^(0.2)on a principal G-bundle P over a compact complex manifold.According to the Koszul-Malgrange criterion,any holomorphic structure on can be seen as a solution to this equation.Suppose that G=SU(2)or SO(3)and X is a complex surface with H_(1)(X,Z_(2))=0.We then prove that the-part curvature of an irreducible Yang-Mills bar connection vanishes,i.e.,(P,δ_(A))is holomorphic.
文摘The novelty of this research lies in the successful fabrication of a 3D-printed honeycomb structure filled with nanofillers for acoustic properties,utilizing an impedance tube setup in accordance with ASTM standard E 1050-12.The Creality Ender-3,a 3D printer,was used for printing the honeycomb structures,and polylactic acid(PLA)material was employed for their construction.The organic,inorganic,and polymeric compounds within the composites were identified using fourier transformation infrared(FTIR)spectroscopy.The structure and homogeneity of the samples were examined using a field emission scanning electron microscope(FESEM).To determine the sound absorption coefficient of the 3D printed honeycomb structure,numerous samples were systematically developed using central composite design(CCD)and analysed using response surface methodology(RSM).The RSM mathematical model was established to predict the optimum values of each factor and noise reduction coefficient(NRC).The optimum values for an NRC of 0.377 were found to be 1.116 wt% carbon black,1.025 wt% aluminium powder,and 3.151 mm distance between parallel edges.Overall,the results demonstrate that a 3Dprinted honeycomb structure filled with nanofillers is an excellent material that can be utilized in various fields,including defence and aviation,where lightweight and acoustic properties are of great importance.
基金Project(51378457)supported by the National Natural Science Foundation of China
文摘An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the main stress trajectories as the representation of force flows on a free-form surface,an automatic grid generation approach is proposed for the architectural design.The algorithm automatically plots the main stress trajectories on a 3D free-form surface,and adopts a modified advancing front meshing technique to generate the structural grid.Based on the proposed algorithm,an automatic grid generator named "St-Surmesh" is developed for the practical architectural design of free-form surface structure.The surface geometry of one of the Sun Valleys in Expo Axis for the Expo Shanghai 2010 is selected as a numerical example for validating the proposed approach.Comparative studies are performed to demonstrate how different structural grids affect the design of a free-form surface structure.
基金Project(52075103)supported by the National Natural Science Foundation of ChinaProject(2020B1515120058)supported by the Key Project of Regional Joint Fund of Guangdong Basic and Applied Basic Research Foundation,China。
文摘Ablation threshold is an important concept in the study of femtosecond laser micro-and nano-machining.In this paper,the ablation experiments of three kinds of surface roughness 4H-Si C substrates irradiated by femtosecond laser were carried out.The feature thresholds were systematically measured for three surface roughness Si C substrates and found in the modification and annealing regions ranging from coincidence(R_(a)=0.5 nm)to a clear demarcation(R_(a)=5.5 nm),eventually being difficult to identify the presence of the former(R_(a)=89 nm).Under multi-pulse laser irradiation,oriented ripple structures were generated in the annealing region,where deep subwavelength ripples(about 110 nm,Λ≈0.2λ)can be generated above substrates with surface roughness higher than 5.5 nm.We investigated the effect of surface roughness on the ablation morphology,ablation threshold,and periodic structures of femtosecond laser ablation of 4H-Si C substrates,while the ablation threshold was tended to decrease and stabilize with the increase of pulse number N≥500.
基金Project(U1334208)supported by the National Natural Science Foundation of ChinaProject(2013GK2001)supported by the Fund of Hunan Provincial Science and Technology Department,China
文摘In order to optimize the crashworthy characteristic of energy-absorbing structures, the surrogate models of specific energy absorption （SEA） and ratio of SEA to initial peak force （REAF） with respect to the design parameters were respectively constructed based on surrogate model optimization methods （polynomial response surface method （PRSM） and Kriging method （KM））. Firstly, the sample data were prepared through the design of experiment （DOE）. Then, the test data models were set up based on the theory of surrogate model, and the data samples were trained to obtain the response relationship between the SEA ＆amp; REAF and design parameters. At last, the structure optimal parameters were obtained by visual analysis and genetic algorithm （GA）. The results indicate that the KM, where the local interpolation method is used in Gauss correlation function, has the highest fitting accuracy and the structure optimal parameters are obtained as： the SEA of 29.8558 kJ/kg （corresponding toa=70 mm andt= 3.5 mm） and REAF of 0.2896 （corresponding toa=70 mm andt=1.9615 mm）. The basis function of the quartic PRSM with higher order than that of the quadratic PRSM, and the mutual influence of the design variables are considered, so the fitting accuracy of the quartic PRSM is higher than that of the quadratic PRSM.
基金Project(51335003)supported by the National Natural Science Foundation of ChinaProject(20111102110011)supported by the Specialized Research Fund for the Doctoral Program of Higher Education of China
文摘The fatigue life of aeroengine turbine disc presents great dispersion due to the randomness of the basic variables,such as applied load,working temperature,geometrical dimensions and material properties.In order to ameliorate reliability analysis efficiency without loss of reliability,the distributed collaborative response surface method(DCRSM) was proposed,and its basic theories were established in this work.Considering the failure dependency among the failure modes,the distributed response surface was constructed to establish the relationship between the failure mode and the relevant random variables.Then,the failure modes were considered as the random variables of system response to obtain the distributed collaborative response surface model based on structure failure criterion.Finally,the given turbine disc structure was employed to illustrate the feasibility and validity of the presented method.Through the comparison of DCRSM,Monte Carlo method(MCM) and the traditional response surface method(RSM),the results show that the computational precision for DCRSM is more consistent with MCM than RSM,while DCRSM needs far less computing time than MCM and RSM under the same simulation conditions.Thus,DCRSM is demonstrated to be a feasible and valid approach for improving the computational efficiency of reliability analysis for aeroengine turbine disc fatigue life with multiple random variables,and has great potential value for the complicated mechanical structure with multi-component and multi-failure mode.
基金Project(Qian Jiao He KY Zi [2021]257) supported provided by the Natural Science Research Project of Education Department of Guizhou Province,ChinaProject(GZSQCC2019003) supported by the High-level Innovative Talent Cultivation Project of Guizhou Province,ChinaProjects(GZLGXM-01,GZLGXM-08) supported by the Academic New Seedling Cultivation and Innovation Exploration Project of Guizhou Institute of Technology,China。
文摘Despite being a promising photoanode material for water splitting,WO_(3) has low conductivity,high onset potential,and sluggish water oxidation kinetics.In this study,we designed Ti-doped WO_(3) nanoplate arrays on fluoride-doped tin oxide by a seed-free hydrothermal method,and the effects of doping on the photoelectrochemical performance were investigated.The optimal Ti-doped WO_(3) electrode achieved a photocurrent density of 0.53 mA/cm^(2) at 0.6 V(vs Ag/AgCl),110%higher than that of pure WO_(3) nanoplate arrays.Moreover,a significant cathodic shift in the onset potential was observed after doping.X-ray photoelectron spectroscopy valence band and ultraviolet–visible spectra revealed that the band positions of Ti-doped WO_(3) photoanodes moved upward,yielding a lower onset potential.Furthermore,electrochemical impedance spectroscopy measurements revealed that the conductivities of the WO_(3) photoanodes improved after doping,because of the rapid separation of photo-generated charge carriers.Thus,we report a new design route toward efficient and low-cost photoanodes for photoelectrochemical applications.
