An LD directly-pumped solid-state laser is considered to be one of the most promising mid-infrared light sources because of its simple principle,small size,and compact structure for the generation of mid-infrared(MIR)...An LD directly-pumped solid-state laser is considered to be one of the most promising mid-infrared light sources because of its simple principle,small size,and compact structure for the generation of mid-infrared(MIR)lasers in the 3-5µm band.However,the quantum defect of LD directly-pumped MIR solid-state lasers will be much larger than that of ordinary near-infrared LD pumped solid-state lasers,which may lead to thermal damage and limit their development.In order to solve this problem,the methods of reducing the specific surface area of the crystal and improving the thermal energy released by the crystal structure are discussed,and the opti⁃mal length of the laser crystal is determined.The cooling structures of barium yttrium fluoride laser crystals(Ho^(3+):BY_(2)F_(8))of different lengths were studied by thermal simulation using COMSOL software.The experimen⁃tal results show that the output power can be increased and the thermal stress in the laser crystal can be alleviated by using the laser crystal whose length is slightly shorter than that of the cooler.The final experiment shows that when the pump repetition rate is 15 Hz and the pulse width is 90µs,the single pulse energy is 7.28 mJ at the out⁃put wavelength of 3.9µm,which is about 3 times as large as that of the crystal with the length of 10 mm(2.81 mJ).Such results should be another breakthrough of our team since the first directly-pumped solid-state MIR laser was realized more than a year ago.It might pave the way for the construction of a feasible MIR laser in the near future.展开更多
In order to obtain a high output energy from a xenon lamp-pumped solid-state dye laser, homogeneities of laser mediums and flatnesses of medium faces with different processing treatments are discussed in the paper. Th...In order to obtain a high output energy from a xenon lamp-pumped solid-state dye laser, homogeneities of laser mediums and flatnesses of medium faces with different processing treatments are discussed in the paper. The mediums without aging treatment, which are prepared by using a prepolymer process and have diamond-machined end faces to produce the required optical finish, give a highest laser output of 281.9 mJ with 0.215% slope efficiency at 2.0x 10^-4 mol/L. The best medium lifetime is 21 shots to 50% of original output equating 74.6 k J/liter.展开更多
A plasma is produced in air by using a high-intensity Q-switch Nd：YAG pulsed laser to irradiate a solid target, and the impulses delivering from the plasma to the target are measured at different laser power densitie...A plasma is produced in air by using a high-intensity Q-switch Nd：YAG pulsed laser to irradiate a solid target, and the impulses delivering from the plasma to the target are measured at different laser power densities. Analysing the formation process of laser plasma and the laser supported detonation wave （LSDW） and using fluid mechanics theory and Pirri＇s methods, an approximately theoretical solution of the impulse delivering from the plasma to the target under our experimental condition is found. Furthermore, according to the formation time of plasma and the variation of pressure in plasma in a non-equilibrium state, a physical model of the interaction between the pulse laser and the solid target is developed. The plasma evolutions with time during and after the laser pulse irradiating the target are simulated numerically by using a three-dimensional difference scheme. And the numerical solutions of the impulse delivering from the plasma to the target are obtained. A comparison among the theoretical, numerical and experimental results and their analyses are performed. The experimental results are explained reasonably. The consistency between numerical results and experimental results implies that the numerical calculation model used in this paper can well describe the mechanical action of the laser on the target.展开更多
Polymers are a kind of attractive hosts for laser dyes due to their high transparency in both pumping and lasing ranges and superior optical homogeneity. In this paper solid dye samples based on polymethyl methacryla...Polymers are a kind of attractive hosts for laser dyes due to their high transparency in both pumping and lasing ranges and superior optical homogeneity. In this paper solid dye samples based on polymethyl methacrylate （PMMA） doped with different concentrations of 1, 3, 5, 7, 8 -pentamethyl-2, 6-diethylpyrromethene-BF2 （PM567） are prepared. The absorption, fluorescence and lasing spectra of the samples are obtained. Wide absorption and fluorescence bands are obtained and a red shift of the maxima of the lasing emission spectra is observed. With the second-harmonic generation of Q-switched Nd：YAC laser （532 nm, -20 ns） pumping the samples longitudinally, the slope efficiencies of the samples are obtained. There is an optimal dye concentration for the highest slope efficiency when the pumping energy is lower than some typical value （-250 mJ）, and the highest slope efficiency 35.6% is obtained in the sample with a dye concentration of 2 × 10^-4 mol/L. Pumping the samples at a rate of 10Hz with a pulse energy as high as 200 mJ （the fluence is 0.2 J/cm^2）, the output energy drops to one-half of its initial value after approximate 15500 pulses and the normalized photostability is 5.17CJ/mol. A kind of solid dye laser which could have some applications is built.展开更多
Laser action in methyl methacrylate （MMA） co-doped with sulforhodamine B and crystal violet dyes was investi- gated. The dye mixture was incorporated into a solid polymeric matrix and was pumped by a 532-nm Nd：YAG ...Laser action in methyl methacrylate （MMA） co-doped with sulforhodamine B and crystal violet dyes was investi- gated. The dye mixture was incorporated into a solid polymeric matrix and was pumped by a 532-nm Nd：YAG laser. Distributed feedback dye laser （DFDL） action was induced in the dye mixture using a prism arrangement both in the donor and acceptor regions by an energy transfer mechanism. Theoretically, the characteristics of acceptor and donor DFDLs, and the dependence of their pulse widths and output powers on acceptor-donor concentrations and pump power, were studied. Experimentally, the output energy of DFDL was measured at the emission peaks of donor and acceptor dyes for different pump powers and different acceptor-donor concentrations. Tuning of the output wavelength was achieved by varying the period of the gain modulation of the laser medium. The laser wavelength showed continuous tunability from 563 nm to 648 nm.展开更多
With the advent of ultrashort high intensity laser pulses, laser absorption during the laser–solid interactions has received significant attention over the last two decades since it is related to a variety of applica...With the advent of ultrashort high intensity laser pulses, laser absorption during the laser–solid interactions has received significant attention over the last two decades since it is related to a variety of applications of high intensity lasers,including the hot electron production for fast ignition of fusion targets, table-top bright X-ray and gamma-ray sources,ion acceleration, compact neutron sources, and generally the creation of high energy density matters. Normally, some absorption mechanisms found for nanosecond long laser pulses also appear for ultrashort laser pulses. The peculiar aspects with ultrashort laser pulses are that their absorption depends significantly on the preplasma condition and the initial target structures. Meanwhile, relativistic nonlinearity and ponderomotive force associated with the laser pulses lead to new mechanisms or phenomena, which are usually not found with nanosecond long pulses. In this paper, we present an overview of the recent progress on the major absorption mechanisms in intense laser–solid interactions, where emphasis is paid to our related theory and simulation studies.展开更多
This paper describes a tunable dual-wavelength Ti：sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd：YAG laser as the pumping source...This paper describes a tunable dual-wavelength Ti：sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd：YAG laser as the pumping source, and the birefringence filter as the tuning element. Tunable dual-wavelength outputs with one wavelength range from 700 nm to 756.5 nm, another from 830 nm to 900mn have been demonstrated. With a pump power of 23 W at 532 nm, a repetition rate of 7 kHz and a pulse width of 47.6 ns, an output power of 5.1 W at 744.8 nm and 860.9 nm with a pulse width of 13.2 ns and a line width of 3 nm has been obtained, it indicates an optical-to-optical conversion efficiency of 22.2%.展开更多
The intrinsic features involving a circularly symmetric beam profile with low divergence, planar geometry as well as the increasingly enhanced power of vertical-cavity surface-emitting lasers （VCSELs） have made the ...The intrinsic features involving a circularly symmetric beam profile with low divergence, planar geometry as well as the increasingly enhanced power of vertical-cavity surface-emitting lasers （VCSELs） have made the VCSEL a promising pump source in direct end bonding to a solid-state laser medium to form the minimized, on-wafer integrated laser system. This scheme will generate a surface contact pump configuration and thus additional end thermal coupling to the laser medium through the joint interface of both materials, apart from pump beam heating. This paper analytically models temperature distributions in both VCSEL and the laser medium from the end thermal coupling regarding surface contact pump configuration using a top-emitting VCSEL as the pump source for the first time. The analytical solutions are derived by introducing relative temperature and mean temperature expressions. The results show that the end contact heating by the VCSEL could lead to considerable temperature variations associated with thermal phase shift and thermal lensing in the laser medium. However, if the central temperature of the interface is increased by less than 20 K, the end contact heating does not have a significant thermal influence on the laser medium. In this case, the thermal effect should be dominated by pump beam heating. This work provides useful analytical results for further analysis of hybrid thermal effects on those lasers pumped by a direct VCSEL bond.展开更多
Solid-state samples based on modified polymethyl methacrylate （MPMMA） with methanol doped with the dye pyrromethene 650 （PM650） axe prepared. The effects of a volume percentage of methanol on the laser characteris...Solid-state samples based on modified polymethyl methacrylate （MPMMA） with methanol doped with the dye pyrromethene 650 （PM650） axe prepared. The effects of a volume percentage of methanol on the laser characteristics of the sample, including spectra properties, slope efficiency, photostability and tunable properties, are investigated. The broadband dye laser output wavelength is around 655 nm and a highest slope efficiency of 32.23% is achieved. Pumping the samples at a repetition rate of 5 Hz with a pulse energy of as high as 100 mJ （the fluence is 0.26 J/cm2）, the longest lifetime （168000 shots） is obtained in the sample （MMA：methanol=18：2）, and the corresponding normalized photostability reaches 109.19 GJ/mol. When the sample （MMA：methanol=18：2） is placed in a Shoshan-type oscilla- tor, the naxrow-linewidth operation is a continuous tuning range （up to 64 nm）. The results indicate that the laser characteristics of solid-state dyes can be greatly enhanced by using modified PMMA with methanol serving as the solid host.展开更多
Diode pumped monolithic nonplanar ring laser has been developed, yielding single frequency laser and has the advantages of compactness, reliability and high efficiency. Its principles are given in detail and a monolit...Diode pumped monolithic nonplanar ring laser has been developed, yielding single frequency laser and has the advantages of compactness, reliability and high efficiency. Its principles are given in detail and a monolithic nonplanar ring laser is designed. As a result, a laser of hundreds milliwatts cw single frequency output was built up, placed in a magnetic field and pumped by LD. The optical conversion efficiency was more than 15% and the slope efficiency more than 30%. The laser beam had a good quality, with M 2 about 1 2.展开更多
We demonstrate an all-solid quasi-continuous-wave （QCW） narrow-band source tunable to sodium D2a line at 589.159 nm. The source is based on sum-frequency mixing between lasers at 1064 nm and 1319 nm in a LBO crystal...We demonstrate an all-solid quasi-continuous-wave （QCW） narrow-band source tunable to sodium D2a line at 589.159 nm. The source is based on sum-frequency mixing between lasers at 1064 nm and 1319 nm in a LBO crystal. The 1064 nm and 1319 nm lasers are produced from two diode side-pumped Nd：YAG master oscillator power amplifier （MOPA） laser systems, respectively. A 33 W output of 589 nm laser is obtained with beam quality factor M^2 = 1.25, frequency stability better than ±0.2 GHz and linewidth less than 0.44 GHz. A prototype 589 nm laser system is assembled, and a sodium laser guided star has been successfully observed in the field test.展开更多
A transmission-type tungsten disulfide（WS_2）-based saturable absorber（SA） is fabricated and applied to passively Q-switched Nd：YVO_4 laser.The WS_2 nanosheets are deposited on a quartz substrate by the vertical e...A transmission-type tungsten disulfide（WS_2）-based saturable absorber（SA） is fabricated and applied to passively Q-switched Nd：YVO_4 laser.The WS_2 nanosheets are deposited on a quartz substrate by the vertical evaporation method.By inserting the WS2 SA into the plano-concave laser cavity,we achieve 153-ns pulses with an average output power of1.19 W at 1064 nm.To the best of our knowledge,both of them are the best results among those obtained by the Q-switched solid-state lasers with WS_2-based absorbers.The repetition rate ranges from 1.176 MHz to 1.578 MHz.As far as we know,it is the first time that MHz level Q-switched pulses have been generated in all solid state lasers based on low-dimensional materials so far.展开更多
The Ho：YAP crystal is grown by the Czochralski technique. The room-temperature polarized absorption spectra of Ho：YAP crystal was measured on a c-cut sample with 1 at% holmium. According to the obtained Judd-Ofelt i...The Ho：YAP crystal is grown by the Czochralski technique. The room-temperature polarized absorption spectra of Ho：YAP crystal was measured on a c-cut sample with 1 at% holmium. According to the obtained Judd-Ofelt intensity parameters Ω2 = 1.42 × 10^-20cm^2, Ω4 = 2.92 ×10^-20 cm^2, and Ω6 =1.71 ×10^-20cm^2, this paper calculated the fluorescence lifetime to be 6 ms for ^5I7→^5Is transition, and the integrated emission cross section to be 2.24 × 10^-18 cm^2. It investigates the room-temperature Ho：YAP laser end-pumped by a 1.91-μm Tm：YLF laser. The maximum output power was 4.1 W when the incident 1.91-μm pump power was 14.4W. The slope efficiency is 40.8%, corresponding to an optical-to-optical conversion efficiency of 28.4%. The Ho：YAP output wavelength was centred at 2118 nm with full width at half maximum of about 0.8nm.展开更多
A diode-pumped solid-state laser （DPSSL） with a high energetic stability and long service life is applied to ablate the steel samples instead of traditional Nd：YAG laser pumped by a xenon lamp, and several factors,...A diode-pumped solid-state laser （DPSSL） with a high energetic stability and long service life is applied to ablate the steel samples instead of traditional Nd：YAG laser pumped by a xenon lamp, and several factors, such as laser pulse energy, repetition rate and argon flow rate, that influence laser-induced breakdown spectroscopy （LIBS） analytical performance are investigated in detail. Under the optimal experiment conditions, the relative standard deviations for C, Si, Mn, Ni, Cr and Cu are 3.3%-8.9%, 0.9%-2.8%, 1.2%-4.1%, 1.7%-3.0%, 1.1%-3.4% and 2.5%-8.5%, respectively, with the corresponding relative errors of 1.1%-7.9%, 1.0%-6.3%, 0.4%-3.9%, 1.5%-6.3%, 1.2%-4.0% and 1.2%-6.4%. Compared with the results of the traditional spark discharge optical emission spectrometry technique, the analytical performance of LIBS is just a little inferior due to the less stable laser-induced plasma and smaller amount of ablated sample by the laser. However, the precision, detection limits and accuracy of LIBS obtained in our present work were sufficient to meet the requirements for process analysis. These technical performances of higher stability of output energy and longer service life for DPSSL, in comparison to the Q-switch laser pumped by xeon lamp, qualify it well for the real time online analysis for different industrial applications.展开更多
This paper demonstrates the passively mode-locked Nd：GdVO4 laser operating on the ^4F3/2-^4I9/2 transition at 912 nm by using a semiconductor saturable-absorber mirror for passive mode locking, stable continuous wave...This paper demonstrates the passively mode-locked Nd：GdVO4 laser operating on the ^4F3/2-^4I9/2 transition at 912 nm by using a semiconductor saturable-absorber mirror for passive mode locking, stable continuous wave modelocked 912nm laser was achieved with a repetition rate of 176 MHz. At the incident pump power of 17.7W, 22.6mW average output power of stable mode-locked laser was obtained with a slope efficiency of 0.3%.展开更多
A compact high power diode-pumped passively mode-locked Nd:YVO_4 laser with high repetition rate is realized.Using an Nd:YVO_4 crystal and a semiconductor saturable absorber mirror(SESAM) in the oscillator, the picose...A compact high power diode-pumped passively mode-locked Nd:YVO_4 laser with high repetition rate is realized.Using an Nd:YVO_4 crystal and a semiconductor saturable absorber mirror(SESAM) in the oscillator, the picosecond pulse output with an average power of 1.38 W, a repetition rate of 3.24 GHz, and a pulse duration of 11.4 ps is achieved. After one stage of amplification, the final output power reaches 11.34 W, corresponding to a total optical-to-optical efficiency of about 32%. The root mean square(RMS) value of power fluctuation is demonstrated to be less than 0.6% in 24 hours,showing a superior stability with the compact configuration.展开更多
We investigate the influence of temperature on the efficiency of diode pumped Nd：YAG heat capacity laser is studied. It is shown that the efficiency of such a laser system is greatly reduced at higher temperature. Th...We investigate the influence of temperature on the efficiency of diode pumped Nd：YAG heat capacity laser is studied. It is shown that the efficiency of such a laser system is greatly reduced at higher temperature. This bad behaviour is mainly caused by the doped-ion redistribution among various Stark levels of the ground state, and by a thermal equilibrium between the upper laser level and the pump level. Meanwhile, the thermal excitations from the ground state to the lower laser level also play a role. We derive a model to describe those effects, with the considerations of emission spectrum of laser diodes, the subtle Stark structures and the linewidth of absorption and of simulated-emission.展开更多
基金Supported by the National Key Research and Development Program of China(2021YFA0718803)。
文摘An LD directly-pumped solid-state laser is considered to be one of the most promising mid-infrared light sources because of its simple principle,small size,and compact structure for the generation of mid-infrared(MIR)lasers in the 3-5µm band.However,the quantum defect of LD directly-pumped MIR solid-state lasers will be much larger than that of ordinary near-infrared LD pumped solid-state lasers,which may lead to thermal damage and limit their development.In order to solve this problem,the methods of reducing the specific surface area of the crystal and improving the thermal energy released by the crystal structure are discussed,and the opti⁃mal length of the laser crystal is determined.The cooling structures of barium yttrium fluoride laser crystals(Ho^(3+):BY_(2)F_(8))of different lengths were studied by thermal simulation using COMSOL software.The experimen⁃tal results show that the output power can be increased and the thermal stress in the laser crystal can be alleviated by using the laser crystal whose length is slightly shorter than that of the cooler.The final experiment shows that when the pump repetition rate is 15 Hz and the pulse width is 90µs,the single pulse energy is 7.28 mJ at the out⁃put wavelength of 3.9µm,which is about 3 times as large as that of the crystal with the length of 10 mm(2.81 mJ).Such results should be another breakthrough of our team since the first directly-pumped solid-state MIR laser was realized more than a year ago.It might pave the way for the construction of a feasible MIR laser in the near future.
文摘In order to obtain a high output energy from a xenon lamp-pumped solid-state dye laser, homogeneities of laser mediums and flatnesses of medium faces with different processing treatments are discussed in the paper. The mediums without aging treatment, which are prepared by using a prepolymer process and have diamond-machined end faces to produce the required optical finish, give a highest laser output of 281.9 mJ with 0.215% slope efficiency at 2.0x 10^-4 mol/L. The best medium lifetime is 21 shots to 50% of original output equating 74.6 k J/liter.
基金Project supported by the National Natural Science Foundation of China (Grant No 60578015)the Specialized Research Fund for the Doctoral Program of Higher Education of China (Grant No 20050288025)the Foundation of the Ministry of Education of China for Outstanding Young Teachers in University (2003-2008)
文摘A plasma is produced in air by using a high-intensity Q-switch Nd：YAG pulsed laser to irradiate a solid target, and the impulses delivering from the plasma to the target are measured at different laser power densities. Analysing the formation process of laser plasma and the laser supported detonation wave （LSDW） and using fluid mechanics theory and Pirri＇s methods, an approximately theoretical solution of the impulse delivering from the plasma to the target under our experimental condition is found. Furthermore, according to the formation time of plasma and the variation of pressure in plasma in a non-equilibrium state, a physical model of the interaction between the pulse laser and the solid target is developed. The plasma evolutions with time during and after the laser pulse irradiating the target are simulated numerically by using a three-dimensional difference scheme. And the numerical solutions of the impulse delivering from the plasma to the target are obtained. A comparison among the theoretical, numerical and experimental results and their analyses are performed. The experimental results are explained reasonably. The consistency between numerical results and experimental results implies that the numerical calculation model used in this paper can well describe the mechanical action of the laser on the target.
文摘Polymers are a kind of attractive hosts for laser dyes due to their high transparency in both pumping and lasing ranges and superior optical homogeneity. In this paper solid dye samples based on polymethyl methacrylate （PMMA） doped with different concentrations of 1, 3, 5, 7, 8 -pentamethyl-2, 6-diethylpyrromethene-BF2 （PM567） are prepared. The absorption, fluorescence and lasing spectra of the samples are obtained. Wide absorption and fluorescence bands are obtained and a red shift of the maxima of the lasing emission spectra is observed. With the second-harmonic generation of Q-switched Nd：YAC laser （532 nm, -20 ns） pumping the samples longitudinally, the slope efficiencies of the samples are obtained. There is an optimal dye concentration for the highest slope efficiency when the pumping energy is lower than some typical value （-250 mJ）, and the highest slope efficiency 35.6% is obtained in the sample with a dye concentration of 2 × 10^-4 mol/L. Pumping the samples at a rate of 10Hz with a pulse energy as high as 200 mJ （the fluence is 0.2 J/cm^2）, the output energy drops to one-half of its initial value after approximate 15500 pulses and the normalized photostability is 5.17CJ/mol. A kind of solid dye laser which could have some applications is built.
文摘Laser action in methyl methacrylate （MMA） co-doped with sulforhodamine B and crystal violet dyes was investi- gated. The dye mixture was incorporated into a solid polymeric matrix and was pumped by a 532-nm Nd：YAG laser. Distributed feedback dye laser （DFDL） action was induced in the dye mixture using a prism arrangement both in the donor and acceptor regions by an energy transfer mechanism. Theoretically, the characteristics of acceptor and donor DFDLs, and the dependence of their pulse widths and output powers on acceptor-donor concentrations and pump power, were studied. Experimentally, the output energy of DFDL was measured at the emission peaks of donor and acceptor dyes for different pump powers and different acceptor-donor concentrations. Tuning of the output wavelength was achieved by varying the period of the gain modulation of the laser medium. The laser wavelength showed continuous tunability from 563 nm to 648 nm.
基金Project supported by the National Basic Research Program of China(Grant No.2013CBA01504)the National Natural Science Foundation of China(Grant Nos.11421064,11129503,11374209,and 11374210)
文摘With the advent of ultrashort high intensity laser pulses, laser absorption during the laser–solid interactions has received significant attention over the last two decades since it is related to a variety of applications of high intensity lasers,including the hot electron production for fast ignition of fusion targets, table-top bright X-ray and gamma-ray sources,ion acceleration, compact neutron sources, and generally the creation of high energy density matters. Normally, some absorption mechanisms found for nanosecond long laser pulses also appear for ultrashort laser pulses. The peculiar aspects with ultrashort laser pulses are that their absorption depends significantly on the preplasma condition and the initial target structures. Meanwhile, relativistic nonlinearity and ponderomotive force associated with the laser pulses lead to new mechanisms or phenomena, which are usually not found with nanosecond long pulses. In this paper, we present an overview of the recent progress on the major absorption mechanisms in intense laser–solid interactions, where emphasis is paid to our related theory and simulation studies.
基金Project supported in part by the National Natural Science Foundation of China （Grant Nos 10474071, 60637010, 60671036 and 60278001） and Tianjin Applied Fundamental Research Project, China （07JCZDJC05900）.
文摘This paper describes a tunable dual-wavelength Ti：sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd：YAG laser as the pumping source, and the birefringence filter as the tuning element. Tunable dual-wavelength outputs with one wavelength range from 700 nm to 756.5 nm, another from 830 nm to 900mn have been demonstrated. With a pump power of 23 W at 532 nm, a repetition rate of 7 kHz and a pulse width of 47.6 ns, an output power of 5.1 W at 744.8 nm and 860.9 nm with a pulse width of 13.2 ns and a line width of 3 nm has been obtained, it indicates an optical-to-optical conversion efficiency of 22.2%.
文摘The intrinsic features involving a circularly symmetric beam profile with low divergence, planar geometry as well as the increasingly enhanced power of vertical-cavity surface-emitting lasers （VCSELs） have made the VCSEL a promising pump source in direct end bonding to a solid-state laser medium to form the minimized, on-wafer integrated laser system. This scheme will generate a surface contact pump configuration and thus additional end thermal coupling to the laser medium through the joint interface of both materials, apart from pump beam heating. This paper analytically models temperature distributions in both VCSEL and the laser medium from the end thermal coupling regarding surface contact pump configuration using a top-emitting VCSEL as the pump source for the first time. The analytical solutions are derived by introducing relative temperature and mean temperature expressions. The results show that the end contact heating by the VCSEL could lead to considerable temperature variations associated with thermal phase shift and thermal lensing in the laser medium. However, if the central temperature of the interface is increased by less than 20 K, the end contact heating does not have a significant thermal influence on the laser medium. In this case, the thermal effect should be dominated by pump beam heating. This work provides useful analytical results for further analysis of hybrid thermal effects on those lasers pumped by a direct VCSEL bond.
基金Project supported by the National Natural Science Foundation of China (Grant No.61008023)the Natural Scientific Research Innovation Foundation in Harbin Institute of Technology,China (Grant No.HIT.NSRIF.2009009)
文摘Solid-state samples based on modified polymethyl methacrylate （MPMMA） with methanol doped with the dye pyrromethene 650 （PM650） axe prepared. The effects of a volume percentage of methanol on the laser characteristics of the sample, including spectra properties, slope efficiency, photostability and tunable properties, are investigated. The broadband dye laser output wavelength is around 655 nm and a highest slope efficiency of 32.23% is achieved. Pumping the samples at a repetition rate of 5 Hz with a pulse energy of as high as 100 mJ （the fluence is 0.26 J/cm2）, the longest lifetime （168000 shots） is obtained in the sample （MMA：methanol=18：2）, and the corresponding normalized photostability reaches 109.19 GJ/mol. When the sample （MMA：methanol=18：2） is placed in a Shoshan-type oscilla- tor, the naxrow-linewidth operation is a continuous tuning range （up to 64 nm）. The results indicate that the laser characteristics of solid-state dyes can be greatly enhanced by using modified PMMA with methanol serving as the solid host.
基金Fundfor Research on Doctoral Programs in Institutions of Higher Learning
文摘Diode pumped monolithic nonplanar ring laser has been developed, yielding single frequency laser and has the advantages of compactness, reliability and high efficiency. Its principles are given in detail and a monolithic nonplanar ring laser is designed. As a result, a laser of hundreds milliwatts cw single frequency output was built up, placed in a magnetic field and pumped by LD. The optical conversion efficiency was more than 15% and the slope efficiency more than 30%. The laser beam had a good quality, with M 2 about 1 2.
文摘We demonstrate an all-solid quasi-continuous-wave （QCW） narrow-band source tunable to sodium D2a line at 589.159 nm. The source is based on sum-frequency mixing between lasers at 1064 nm and 1319 nm in a LBO crystal. The 1064 nm and 1319 nm lasers are produced from two diode side-pumped Nd：YAG master oscillator power amplifier （MOPA） laser systems, respectively. A 33 W output of 589 nm laser is obtained with beam quality factor M^2 = 1.25, frequency stability better than ±0.2 GHz and linewidth less than 0.44 GHz. A prototype 589 nm laser system is assembled, and a sodium laser guided star has been successfully observed in the field test.
基金Project supported by the National Natural Science Foundation of China(Grant No.61378024)
文摘A transmission-type tungsten disulfide（WS_2）-based saturable absorber（SA） is fabricated and applied to passively Q-switched Nd：YVO_4 laser.The WS_2 nanosheets are deposited on a quartz substrate by the vertical evaporation method.By inserting the WS2 SA into the plano-concave laser cavity,we achieve 153-ns pulses with an average output power of1.19 W at 1064 nm.To the best of our knowledge,both of them are the best results among those obtained by the Q-switched solid-state lasers with WS_2-based absorbers.The repetition rate ranges from 1.176 MHz to 1.578 MHz.As far as we know,it is the first time that MHz level Q-switched pulses have been generated in all solid state lasers based on low-dimensional materials so far.
基金supported by the Program of Excellent Team in Harbin Institute of Technology of China
文摘The Ho：YAP crystal is grown by the Czochralski technique. The room-temperature polarized absorption spectra of Ho：YAP crystal was measured on a c-cut sample with 1 at% holmium. According to the obtained Judd-Ofelt intensity parameters Ω2 = 1.42 × 10^-20cm^2, Ω4 = 2.92 ×10^-20 cm^2, and Ω6 =1.71 ×10^-20cm^2, this paper calculated the fluorescence lifetime to be 6 ms for ^5I7→^5Is transition, and the integrated emission cross section to be 2.24 × 10^-18 cm^2. It investigates the room-temperature Ho：YAP laser end-pumped by a 1.91-μm Tm：YLF laser. The maximum output power was 4.1 W when the incident 1.91-μm pump power was 14.4W. The slope efficiency is 40.8%, corresponding to an optical-to-optical conversion efficiency of 28.4%. The Ho：YAP output wavelength was centred at 2118 nm with full width at half maximum of about 0.8nm.
基金supported by the Development Fund of National Autonomous Demonstration Innovation Zone of Shandong Peninsula(Grant No.ZCQ17104)the National Key Research and Development Program of China(Grant No.2017YFB0305400)‘double hundred plan’ Yantai talent funding project
文摘A diode-pumped solid-state laser （DPSSL） with a high energetic stability and long service life is applied to ablate the steel samples instead of traditional Nd：YAG laser pumped by a xenon lamp, and several factors, such as laser pulse energy, repetition rate and argon flow rate, that influence laser-induced breakdown spectroscopy （LIBS） analytical performance are investigated in detail. Under the optimal experiment conditions, the relative standard deviations for C, Si, Mn, Ni, Cr and Cu are 3.3%-8.9%, 0.9%-2.8%, 1.2%-4.1%, 1.7%-3.0%, 1.1%-3.4% and 2.5%-8.5%, respectively, with the corresponding relative errors of 1.1%-7.9%, 1.0%-6.3%, 0.4%-3.9%, 1.5%-6.3%, 1.2%-4.0% and 1.2%-6.4%. Compared with the results of the traditional spark discharge optical emission spectrometry technique, the analytical performance of LIBS is just a little inferior due to the less stable laser-induced plasma and smaller amount of ablated sample by the laser. However, the precision, detection limits and accuracy of LIBS obtained in our present work were sufficient to meet the requirements for process analysis. These technical performances of higher stability of output energy and longer service life for DPSSL, in comparison to the Q-switch laser pumped by xeon lamp, qualify it well for the real time online analysis for different industrial applications.
基金Project supported by the National Natural Science Foundation of China （Grant Nos 60225005, 60308001, 60321003 and 60490280）.
文摘This paper demonstrates the passively mode-locked Nd：GdVO4 laser operating on the ^4F3/2-^4I9/2 transition at 912 nm by using a semiconductor saturable-absorber mirror for passive mode locking, stable continuous wave modelocked 912nm laser was achieved with a repetition rate of 176 MHz. At the incident pump power of 17.7W, 22.6mW average output power of stable mode-locked laser was obtained with a slope efficiency of 0.3%.
基金Project supported by the Strategic Priority Research Program of Chinese Academy of Sciences(Grant No.XDB16030200)the National Natural Science Foundation of China(Grant Nos.11774410 and 61575217)+1 种基金the National Key Scientific Instruments Development Program of China(Grant No.2012YQ120047)the Key Research Program of Frontier Sciences of Chinese Academy of Sciences(Grant No.KJZD-EW-L11-03)
文摘A compact high power diode-pumped passively mode-locked Nd:YVO_4 laser with high repetition rate is realized.Using an Nd:YVO_4 crystal and a semiconductor saturable absorber mirror(SESAM) in the oscillator, the picosecond pulse output with an average power of 1.38 W, a repetition rate of 3.24 GHz, and a pulse duration of 11.4 ps is achieved. After one stage of amplification, the final output power reaches 11.34 W, corresponding to a total optical-to-optical efficiency of about 32%. The root mean square(RMS) value of power fluctuation is demonstrated to be less than 0.6% in 24 hours,showing a superior stability with the compact configuration.
文摘We investigate the influence of temperature on the efficiency of diode pumped Nd：YAG heat capacity laser is studied. It is shown that the efficiency of such a laser system is greatly reduced at higher temperature. This bad behaviour is mainly caused by the doped-ion redistribution among various Stark levels of the ground state, and by a thermal equilibrium between the upper laser level and the pump level. Meanwhile, the thermal excitations from the ground state to the lower laser level also play a role. We derive a model to describe those effects, with the considerations of emission spectrum of laser diodes, the subtle Stark structures and the linewidth of absorption and of simulated-emission.
