Previous studies have confirmed that an active suspension system with high speed ON/OFF solenoid valves could provide the same vibration isolation efficiency as that of system with pressure proportional valve. In this...Previous studies have confirmed that an active suspension system with high speed ON/OFF solenoid valves could provide the same vibration isolation efficiency as that of system with pressure proportional valve. In this study, by using Linear-quadratic optimization technique and Kalman filter method, an optimal regulator controller with a state observer was designed for the proposed system. Simulation and experimental research was conducted on a quarter car model. The simulation analysis of the system frequency characteristic suggested that the peak value of magnitude response curve in the case of system with an optimal controller would be lowered significantly, and the experiment results also showed that an improvement in the vibration isolation effect was obtained in using the designed optimal controller over the sky hook damper controller.展开更多
A multi-domain nonlinear dynamic model of a proportional solenoid valve was presented.The electro-magnetic,mechanical and fluid subsystems of the valve were investigated,including their interactions.Governing equation...A multi-domain nonlinear dynamic model of a proportional solenoid valve was presented.The electro-magnetic,mechanical and fluid subsystems of the valve were investigated,including their interactions.Governing equations of the valve were derived in the form of nonlinear state equations.By comparing the simulated and measured data,the simulation model is validated with a deviation less than 15%,which can be used for the structural design and control algorithm optimization of proportional solenoid valves.展开更多
A hydraulic position system was designed employing two high speed On/Off solenoid valves with PWM(Pulse width modulation) technique and using LQ(Linear Quadratic) optimization principle. Based on the system, the parts...A hydraulic position system was designed employing two high speed On/Off solenoid valves with PWM(Pulse width modulation) technique and using LQ(Linear Quadratic) optimization principle. Based on the system, the parts of system can be formulated with equations. According to equations, the mathematical model of the system was established. By simulation, the corresponding LQ optimal controller was designed and the PWM signals were generated. The comparison of the simulation and experiment results show that LQ optimal control method with PWM technique employing high speed On/Off solenoid valve can provide better system performance and a high position precision is obtained.展开更多
An algorithm for precisely calculating the inductance of a three-section solenoid is presented, which is based on summing the layer self-inductances and the mutual inductances. A theoretical model with ex plicit expre...An algorithm for precisely calculating the inductance of a three-section solenoid is presented, which is based on summing the layer self-inductances and the mutual inductances. A theoretical model with ex plicit expressions is firstly developed to calculate the self-inductance of a single layer, and then numerical calcu lation of the mutual inductance between two layers is introduced. Using the presented computation method, the inductance of a solenoid designed in the experiment is successfully calculated （4.30 mH）, which has a difference of less than 1% from the experimental data.展开更多
文摘Previous studies have confirmed that an active suspension system with high speed ON/OFF solenoid valves could provide the same vibration isolation efficiency as that of system with pressure proportional valve. In this study, by using Linear-quadratic optimization technique and Kalman filter method, an optimal regulator controller with a state observer was designed for the proposed system. Simulation and experimental research was conducted on a quarter car model. The simulation analysis of the system frequency characteristic suggested that the peak value of magnitude response curve in the case of system with an optimal controller would be lowered significantly, and the experiment results also showed that an improvement in the vibration isolation effect was obtained in using the designed optimal controller over the sky hook damper controller.
基金Project(2008ZHZX1A0502) supported by the Independence Innovation Achievements Transformation Crucial Special Program of Shandong Province,China
文摘A multi-domain nonlinear dynamic model of a proportional solenoid valve was presented.The electro-magnetic,mechanical and fluid subsystems of the valve were investigated,including their interactions.Governing equations of the valve were derived in the form of nonlinear state equations.By comparing the simulated and measured data,the simulation model is validated with a deviation less than 15%,which can be used for the structural design and control algorithm optimization of proportional solenoid valves.
文摘A hydraulic position system was designed employing two high speed On/Off solenoid valves with PWM(Pulse width modulation) technique and using LQ(Linear Quadratic) optimization principle. Based on the system, the parts of system can be formulated with equations. According to equations, the mathematical model of the system was established. By simulation, the corresponding LQ optimal controller was designed and the PWM signals were generated. The comparison of the simulation and experiment results show that LQ optimal control method with PWM technique employing high speed On/Off solenoid valve can provide better system performance and a high position precision is obtained.
文摘An algorithm for precisely calculating the inductance of a three-section solenoid is presented, which is based on summing the layer self-inductances and the mutual inductances. A theoretical model with ex plicit expressions is firstly developed to calculate the self-inductance of a single layer, and then numerical calcu lation of the mutual inductance between two layers is introduced. Using the presented computation method, the inductance of a solenoid designed in the experiment is successfully calculated （4.30 mH）, which has a difference of less than 1% from the experimental data.
