A partition of unity finite element method for numerical simulation of short wave propagation in solids is presented. The finite element spaces were constructed by multiplying the standard isoparametric finite element...A partition of unity finite element method for numerical simulation of short wave propagation in solids is presented. The finite element spaces were constructed by multiplying the standard isoparametric finite element shape functions, which form a partition of unity, with the local subspaces defined on the corresponding shape functions, which include a priori knowledge about the wave motion equation in trial spaces and approximately reproduce the highly oscillatory properties within a single element. Numerical examples demonstrate the performance of the proposed partition of unity finite element in both computational accuracy and efficiency.展开更多
GOA型TFT LCD产品Shorting Bar testing工序烧伤现象严重,针对把根源归结为Shorting Bar Testing工序测试参数电压过高的假设,设计一个Source电压远高于理论测试电压的测试波形,分别以高压值参数和理论值参数对样品进行测试,结果发现两...GOA型TFT LCD产品Shorting Bar testing工序烧伤现象严重,针对把根源归结为Shorting Bar Testing工序测试参数电压过高的假设,设计一个Source电压远高于理论测试电压的测试波形,分别以高压值参数和理论值参数对样品进行测试,结果发现两种情况下烧伤概率一样;针对把根源归结为Shorting Bar testing工序驱动程序启动瞬间冲击烧伤的假设,在测试驱动板上每个测试信号输入口加一个限流器,用加限流器和没加限流器的测试治具分别对样品进行测试,结果发现两者烧伤概率一样;针对把根源归结为静电击伤的假设,在Shorting Bar testing工序增加防静电措施,分别在改进前后的测试环境对样品进行测试,发现改进后未出现烧伤现象。可见出烧伤现象的根源在于静电,而非其他原因。展开更多
To eliminate the aliasing that appeared during the measurement of multi-components nonstationary signals, a novel kind of anti-aliasing algorithm based on the short time Fourier transform （STFT） is brought forward. ...To eliminate the aliasing that appeared during the measurement of multi-components nonstationary signals, a novel kind of anti-aliasing algorithm based on the short time Fourier transform （STFT） is brought forward. First the physical essence of aliasing that occurs is analyzed; second the interpolation algorithm model is setup based on the Hamming window; then the fast implementation of the algorithm using the Newton iteration method is given. Using the numerical simulation the feasibility of algorithm is validated. Finally, the electrical circuit experiment shows the practicality of the algorithm in the electrical engineering.展开更多
A focused ultrasonic transducer used for biomedical purposes with a fundamental frequency of 10MHz and a pulse width of one and a half periods is described in this paper. Its physical properties are given including (1...A focused ultrasonic transducer used for biomedical purposes with a fundamental frequency of 10MHz and a pulse width of one and a half periods is described in this paper. Its physical properties are given including (1) focused acoustic field recorded by an optical means, (2) electric waveform for triggering the transducer and the corresponding waveform of the wave received by another transducer, and (3) result of tests on a sample object.展开更多
Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler （Cr（a-Al2O3）/geopolymer composites） were fabricated, and the effects of heat treatment temperatures up t...Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler （Cr（a-Al2O3）/geopolymer composites） were fabricated, and the effects of heat treatment temperatures up to 1 200 ℃ on the thermal-mechanical properties were studied. The results show that the thermal shrinkage in the direction perpendicular to the lamination of the composites gradually increases with the increase of the heat treatment temperatures from room temperature （25 ℃ ） to 1000 ℃. However, the composites in the direction parallel to the lamination show an expansion behavior. Beyond 1 000℃, in the two directions the composites exhibit a larger degree of shrinkage due to the densification and crystallization. The mechanical properties of the composites show the minimum values in the temperature range from 600 to 800 ℃ as the hydration water of geopolymer matrix is lost. The addition of α-Al2O3 particle filler into the composites clearly increases the onset crystalline temperature of leucite （KAlSi2O6） from the amorphous geopolymer matrix. In addition, the addition of α-Al2O3 particles into the composites can not only help to keep volume stable at high temperatures but also effectively improve the mechanical properties of the composites subjected to thermal load to a certain extent. The main toughening mechanisms of the composites subjected to thermal load are attributed to fiber pulling-out.展开更多
Micro-TATB particles with different sizes and 3D nanoporous TATB architectures with different specific surface areas were prepared through recrystallization to study short pulse duration shock initiation properties by...Micro-TATB particles with different sizes and 3D nanoporous TATB architectures with different specific surface areas were prepared through recrystallization to study short pulse duration shock initiation properties by electric gun technology.For micro-TATB,the initiation threshold significantly decreases with TATB average size ranging from 79.7μm to 0.5μm.For 3D nanoporous TATB architecture,the initiation threshold decreases and then increases with specific surface areas increased from 9.6 m^2/g to36.2 m^2/g.The lowest initiation thresholds are obtained for the micro-TATB with average sizes of 1.3μm and 0.5μm,and 3D nanoporous TATB architecture with specific surface area of 22.4 m^2/g.The shock initiation thresholds of micro-TATB and 3D nanoporous TATB architectures show significantly decreases with the porosity increased.The decomposition reaction and thermal conductivity properties were further investigated to understand the initial response mechanism.High porosity provides more collapse sites to generate high temperature for formation of hot spots.The low thermal conductivity and decomposition temperature could enhance the formation and ignition of the hot spots,and initial decomposition reaction of TATB.The effect of the decomposition temperature is higher than that of the thermal conductivity on the shock initiation properties.The enhanced decomposition reaction could pro mote energy release and transfer process from the ignition to the combustio n.This work offe rs a new insight to understand the effects of microstructure on the shock initiation properties and the initial response mechanism of TATB.展开更多
Background： With the rapid development of genomics, many functional genes have been targeted. Molecular marker assisted selection can accelerate the breeding process by linking selection to functional genes. Methods...Background： With the rapid development of genomics, many functional genes have been targeted. Molecular marker assisted selection can accelerate the breeding process by linking selection to functional genes. Methods： In a study of upland cotton （Gossypium hirsutum L.）, the F2 segregated population was constructed by crossing X1570 （short branches） with Ekangmian 13 （long branches） to identify the short fruiting branch gene and marker assisted selection with SNP（Single Nucleotide Polymorphisms, SNP） linked to its trait. Result： The result demonstrated that linked SSR marker BNL3232 was screened by BSA（Bulked segregant analysis, BSA） method; one SNP locus was found, which was totally separated from the fruiting branches trait in upland cotton. Conclusion： It was verified that this SNP marker could be used for molecular assisted selection of cotton architecture展开更多
In the post World War Ⅱ decades, there is a strong realistic trend in American Short stories. The great achievement made by the new realistic short stories has contributed much to the post war flourishing of American...In the post World War Ⅱ decades, there is a strong realistic trend in American Short stories. The great achievement made by the new realistic short stories has contributed much to the post war flourishing of American short fiction as a whole. In this essay, the mjaor works in this trend are brought under the discussion.展开更多
Different guide vane structures will affect the flow inside the pump,and then affect the transformation of the pressure energy and kinetic energy,and change the velocity distribution of the pump outlet.In order to stu...Different guide vane structures will affect the flow inside the pump,and then affect the transformation of the pressure energy and kinetic energy,and change the velocity distribution of the pump outlet.In order to study the influence of long and short guide vanes on the water-jet pump,on the basis of conventional design,eight schemes of guide vane with different vertical heights were designed in the method of computational fluid dynamics for numerical calculation,the performance curve of water-jet pumps with different long and short guide vanes was obtained,and finally the influence of different guide vanes on hydraulic performance and internal flow was analyzed.The results show that all of schemes reducing the height of blade can improve the head and efficiency.In the schemes reducing the height on the shroud,the guide vanes that the height of the blade is equal to the height difference between hub and shroud in impeller have the highest head and efficiency.In all schemes decreasing the blade height,with the increase of the height difference,the velocity increases gradually and the distribution of turbulence kinetic energy becomes more reasonable in the guide vane outlet.The schemes reducing the height on the hub have more reasonable distribution of velocity and turbulence kinetic energy according to schemes reducing the height on the shroud.The guide vanes of long and short blades can be used to stagger the position of the diffusion flow generated by adjacent blades,which can reduce the effect of the velocity circulation and make the flow of the outlet position more stable.展开更多
From Octobet 1998 to January 1999,5 earthquakes ( M s≥5) occurred between Ninglang and Yanyuan counties (27°07′～27°12′N,100°40′～101°00′E area).They were situated in 140km southwest of the Xi...From Octobet 1998 to January 1999,5 earthquakes ( M s≥5) occurred between Ninglang and Yanyuan counties (27°07′～27°12′N,100°40′～101°00′E area).They were situated in 140km southwest of the Xichang.Among them,the largest one is M s 6 2 on November 19,1998.Based on small seismic data by the seismic remote sensing station of Xichang and the seismological station of Muli,and regional observation data,passing through careful observation and scientific analyses,we had made better forecasts before the earthquakes.That results obvious social benefits.By processing data of precursory earthquakes,such as,original observation data of total geomagnetic intensity from the station of Xichang,pressure capacitance stressometer and quartz horizaontal pendulum tiltmeter from the Xiaomiao station of Xichang,we summarized the sequence characteristics of the series earthquakes.The information about short\|term anomaly of gruond strain,total geomagnetic intensity and ground tilt before the earthquake is emphatically explained.展开更多
This paper presents an approach to the challenging is- sue of passive source localization in shallow water using a mobile short horizontal linear array with length less than ten meters. The short array can be convenie...This paper presents an approach to the challenging is- sue of passive source localization in shallow water using a mobile short horizontal linear array with length less than ten meters. The short array can be conveniently placed on autonomous underwa- ter vehicles and deployed for adaptive spatial sampling. However, the use of such small aperture passive sonar systems makes it difficult to acquire sufficient spatial gain for localizing long-range sources. To meet the requirement, a localization approach that employs matched-field based techniques that enable the short ho- rizontal linear array is used to passively localize acoustic sources in shallow water. Furthermore, the broadband processing and inter-position processing provide robustness against ocean en- vironmental mismatch and enhance the stability of the estimation process. The proposed approach＇s ability to localize acoustic sources in shallow water at different signal-to-noise ratios is examined through the synthetic test cases where the sources are located at the endfire and some other bearing of the mobile short horizontal linear array. The presented results demonstrate that the positional parameters of the estimated source build up over time as the array moves at a low speed along a straight line at a constant depth.展开更多
The GPS multipath signal model is presented, which indicates that the coherent DLL outputs in multipath environment are the convolution between the ideal DLL outputs and the channel responses. So the channel responses...The GPS multipath signal model is presented, which indicates that the coherent DLL outputs in multipath environment are the convolution between the ideal DLL outputs and the channel responses. So the channel responses can be estimated by a least square method using the observed curve of the DLL discriminator. In terms of the estimated multipath channels, two multipath mitigation methods are discussed, which are equalization filtering and multipath subtracting, respectively. It is shown, by computer simulation, that the least square method has a good performance in channels estimation and the multipath errors can be mitigated almost completely by either of the methods. However, the multipath subtracting method has relative small remnant errors than equalization filtering.展开更多
On the contemporary scene of American literature, realism remains one of the main modes of expressions. Apart form realistic thematic concerns, the American post war realistic short fiction also exhibits its nature by...On the contemporary scene of American literature, realism remains one of the main modes of expressions. Apart form realistic thematic concerns, the American post war realistic short fiction also exhibits its nature by successful portrayal of a whole gallery of typical characters. In this essay, some major works are brought under the discussion.展开更多
基金Project supported by the National Basic Research Program of China (973Project) (No.2002CB412709) and the National Natural Science Foundation of China (Nos.50278012,10272027,19832010)
文摘A partition of unity finite element method for numerical simulation of short wave propagation in solids is presented. The finite element spaces were constructed by multiplying the standard isoparametric finite element shape functions, which form a partition of unity, with the local subspaces defined on the corresponding shape functions, which include a priori knowledge about the wave motion equation in trial spaces and approximately reproduce the highly oscillatory properties within a single element. Numerical examples demonstrate the performance of the proposed partition of unity finite element in both computational accuracy and efficiency.
文摘GOA型TFT LCD产品Shorting Bar testing工序烧伤现象严重,针对把根源归结为Shorting Bar Testing工序测试参数电压过高的假设,设计一个Source电压远高于理论测试电压的测试波形,分别以高压值参数和理论值参数对样品进行测试,结果发现两种情况下烧伤概率一样;针对把根源归结为Shorting Bar testing工序驱动程序启动瞬间冲击烧伤的假设,在测试驱动板上每个测试信号输入口加一个限流器,用加限流器和没加限流器的测试治具分别对样品进行测试,结果发现两者烧伤概率一样;针对把根源归结为静电击伤的假设,在Shorting Bar testing工序增加防静电措施,分别在改进前后的测试环境对样品进行测试,发现改进后未出现烧伤现象。可见出烧伤现象的根源在于静电,而非其他原因。
基金the National Natural Science Foundation of China (90407007 60372001).
文摘To eliminate the aliasing that appeared during the measurement of multi-components nonstationary signals, a novel kind of anti-aliasing algorithm based on the short time Fourier transform （STFT） is brought forward. First the physical essence of aliasing that occurs is analyzed; second the interpolation algorithm model is setup based on the Hamming window; then the fast implementation of the algorithm using the Newton iteration method is given. Using the numerical simulation the feasibility of algorithm is validated. Finally, the electrical circuit experiment shows the practicality of the algorithm in the electrical engineering.
文摘A focused ultrasonic transducer used for biomedical purposes with a fundamental frequency of 10MHz and a pulse width of one and a half periods is described in this paper. Its physical properties are given including (1) focused acoustic field recorded by an optical means, (2) electric waveform for triggering the transducer and the corresponding waveform of the wave received by another transducer, and (3) result of tests on a sample object.
基金Project supported by the Science Fund for Distinguished Young Scholars of Heilongjiang Province, ChinaProject supported by the Program for Excellent Team in Harbin Institute of Technology
文摘Short carbon fiber preform reinforced geopolymer composites containing different contents of α-Al2O3 filler （Cr（a-Al2O3）/geopolymer composites） were fabricated, and the effects of heat treatment temperatures up to 1 200 ℃ on the thermal-mechanical properties were studied. The results show that the thermal shrinkage in the direction perpendicular to the lamination of the composites gradually increases with the increase of the heat treatment temperatures from room temperature （25 ℃ ） to 1000 ℃. However, the composites in the direction parallel to the lamination show an expansion behavior. Beyond 1 000℃, in the two directions the composites exhibit a larger degree of shrinkage due to the densification and crystallization. The mechanical properties of the composites show the minimum values in the temperature range from 600 to 800 ℃ as the hydration water of geopolymer matrix is lost. The addition of α-Al2O3 particle filler into the composites clearly increases the onset crystalline temperature of leucite （KAlSi2O6） from the amorphous geopolymer matrix. In addition, the addition of α-Al2O3 particles into the composites can not only help to keep volume stable at high temperatures but also effectively improve the mechanical properties of the composites subjected to thermal load to a certain extent. The main toughening mechanisms of the composites subjected to thermal load are attributed to fiber pulling-out.
基金supported by National Natural Science Foundation of China(11702265,11872341 and 11602238)。
文摘Micro-TATB particles with different sizes and 3D nanoporous TATB architectures with different specific surface areas were prepared through recrystallization to study short pulse duration shock initiation properties by electric gun technology.For micro-TATB,the initiation threshold significantly decreases with TATB average size ranging from 79.7μm to 0.5μm.For 3D nanoporous TATB architecture,the initiation threshold decreases and then increases with specific surface areas increased from 9.6 m^2/g to36.2 m^2/g.The lowest initiation thresholds are obtained for the micro-TATB with average sizes of 1.3μm and 0.5μm,and 3D nanoporous TATB architecture with specific surface area of 22.4 m^2/g.The shock initiation thresholds of micro-TATB and 3D nanoporous TATB architectures show significantly decreases with the porosity increased.The decomposition reaction and thermal conductivity properties were further investigated to understand the initial response mechanism.High porosity provides more collapse sites to generate high temperature for formation of hot spots.The low thermal conductivity and decomposition temperature could enhance the formation and ignition of the hot spots,and initial decomposition reaction of TATB.The effect of the decomposition temperature is higher than that of the thermal conductivity on the shock initiation properties.The enhanced decomposition reaction could pro mote energy release and transfer process from the ignition to the combustio n.This work offe rs a new insight to understand the effects of microstructure on the shock initiation properties and the initial response mechanism of TATB.
基金Sponsored by State Key Laboratory of Cotton Biology Open Fund(CB2016A07)Hubei Provincial Agricultural Science and Technology Innovation Center Support Project(2016–620–000-001-010)The National Key Technology R&D Program(2014BAD11B0203)
文摘Background： With the rapid development of genomics, many functional genes have been targeted. Molecular marker assisted selection can accelerate the breeding process by linking selection to functional genes. Methods： In a study of upland cotton （Gossypium hirsutum L.）, the F2 segregated population was constructed by crossing X1570 （short branches） with Ekangmian 13 （long branches） to identify the short fruiting branch gene and marker assisted selection with SNP（Single Nucleotide Polymorphisms, SNP） linked to its trait. Result： The result demonstrated that linked SSR marker BNL3232 was screened by BSA（Bulked segregant analysis, BSA） method; one SNP locus was found, which was totally separated from the fruiting branches trait in upland cotton. Conclusion： It was verified that this SNP marker could be used for molecular assisted selection of cotton architecture
文摘In the post World War Ⅱ decades, there is a strong realistic trend in American Short stories. The great achievement made by the new realistic short stories has contributed much to the post war flourishing of American short fiction as a whole. In this essay, the mjaor works in this trend are brought under the discussion.
基金The Fundamental Research Funds for the Central Universities(JD2016XGKP1062)
文摘Different guide vane structures will affect the flow inside the pump,and then affect the transformation of the pressure energy and kinetic energy,and change the velocity distribution of the pump outlet.In order to study the influence of long and short guide vanes on the water-jet pump,on the basis of conventional design,eight schemes of guide vane with different vertical heights were designed in the method of computational fluid dynamics for numerical calculation,the performance curve of water-jet pumps with different long and short guide vanes was obtained,and finally the influence of different guide vanes on hydraulic performance and internal flow was analyzed.The results show that all of schemes reducing the height of blade can improve the head and efficiency.In the schemes reducing the height on the shroud,the guide vanes that the height of the blade is equal to the height difference between hub and shroud in impeller have the highest head and efficiency.In all schemes decreasing the blade height,with the increase of the height difference,the velocity increases gradually and the distribution of turbulence kinetic energy becomes more reasonable in the guide vane outlet.The schemes reducing the height on the hub have more reasonable distribution of velocity and turbulence kinetic energy according to schemes reducing the height on the shroud.The guide vanes of long and short blades can be used to stagger the position of the diffusion flow generated by adjacent blades,which can reduce the effect of the velocity circulation and make the flow of the outlet position more stable.
文摘From Octobet 1998 to January 1999,5 earthquakes ( M s≥5) occurred between Ninglang and Yanyuan counties (27°07′～27°12′N,100°40′～101°00′E area).They were situated in 140km southwest of the Xichang.Among them,the largest one is M s 6 2 on November 19,1998.Based on small seismic data by the seismic remote sensing station of Xichang and the seismological station of Muli,and regional observation data,passing through careful observation and scientific analyses,we had made better forecasts before the earthquakes.That results obvious social benefits.By processing data of precursory earthquakes,such as,original observation data of total geomagnetic intensity from the station of Xichang,pressure capacitance stressometer and quartz horizaontal pendulum tiltmeter from the Xiaomiao station of Xichang,we summarized the sequence characteristics of the series earthquakes.The information about short\|term anomaly of gruond strain,total geomagnetic intensity and ground tilt before the earthquake is emphatically explained.
基金supported by the State Scholarship Fund(2011611091)supported by China Shipbuilding Industry Corporation
文摘This paper presents an approach to the challenging is- sue of passive source localization in shallow water using a mobile short horizontal linear array with length less than ten meters. The short array can be conveniently placed on autonomous underwa- ter vehicles and deployed for adaptive spatial sampling. However, the use of such small aperture passive sonar systems makes it difficult to acquire sufficient spatial gain for localizing long-range sources. To meet the requirement, a localization approach that employs matched-field based techniques that enable the short ho- rizontal linear array is used to passively localize acoustic sources in shallow water. Furthermore, the broadband processing and inter-position processing provide robustness against ocean en- vironmental mismatch and enhance the stability of the estimation process. The proposed approach＇s ability to localize acoustic sources in shallow water at different signal-to-noise ratios is examined through the synthetic test cases where the sources are located at the endfire and some other bearing of the mobile short horizontal linear array. The presented results demonstrate that the positional parameters of the estimated source build up over time as the array moves at a low speed along a straight line at a constant depth.
文摘The GPS multipath signal model is presented, which indicates that the coherent DLL outputs in multipath environment are the convolution between the ideal DLL outputs and the channel responses. So the channel responses can be estimated by a least square method using the observed curve of the DLL discriminator. In terms of the estimated multipath channels, two multipath mitigation methods are discussed, which are equalization filtering and multipath subtracting, respectively. It is shown, by computer simulation, that the least square method has a good performance in channels estimation and the multipath errors can be mitigated almost completely by either of the methods. However, the multipath subtracting method has relative small remnant errors than equalization filtering.
基金Supported by National High Technology Research and Development Program of China （863 Program） （2007AA11Z221）, International Cooperation Project of Shanghai （08210707500）, and Natural Science Foundation of Shanghai.（08ZR1420600） . _
文摘On the contemporary scene of American literature, realism remains one of the main modes of expressions. Apart form realistic thematic concerns, the American post war realistic short fiction also exhibits its nature by successful portrayal of a whole gallery of typical characters. In this essay, some major works are brought under the discussion.
