Modern warfare demands weapons capable of penetrating substantial structures,which presents sig-nificant challenges to the reliability of the electronic devices that are crucial to the weapon's perfor-mance.Due to...Modern warfare demands weapons capable of penetrating substantial structures,which presents sig-nificant challenges to the reliability of the electronic devices that are crucial to the weapon's perfor-mance.Due to miniaturization of electronic components,it is challenging to directly measure or numerically predict the mechanical response of small-sized critical interconnections in board-level packaging structures to ensure the mechanical reliability of electronic devices in projectiles under harsh working conditions.To address this issue,an indirect measurement method using the Bayesian regularization-based load identification was proposed in this study based on finite element(FE)pre-dictions to estimate the load applied on critical interconnections of board-level packaging structures during the process of projectile penetration.For predicting the high-strain-rate penetration process,an FE model was established with elasto-plastic constitutive models of the representative packaging ma-terials(that is,solder material and epoxy molding compound)in which material constitutive parameters were calibrated against the experimental results by using the split-Hopkinson pressure bar.As the impact-induced dynamic bending of the printed circuit board resulted in an alternating tensile-compressive loading on the solder joints during penetration,the corner solder joints in the edge re-gions experience the highest S11 and strain,making them more prone to failure.Based on FE predictions at different structural scales,an improved Bayesian method based on augmented Tikhonov regulariza-tion was theoretically proposed to address the issues of ill-posed matrix inversion and noise sensitivity in the load identification at the critical solder joints.By incorporating a wavelet thresholding technique,the method resolves the problem of poor load identification accuracy at high noise levels.The proposed method achieves satisfactorily small relative errors and high correlation coefficients in identifying the mechanical response of local interconnections in board-level packaging structures,while significantly balancing the smoothness of response curves with the accuracy of peak identification.At medium and low noise levels,the relative error is less than 6%,while it is less than 10%at high noise levels.The proposed method provides an effective indirect approach for the boundary conditions of localized solder joints during the projectile penetration process,and its philosophy can be readily extended to other scenarios of multiscale analysis for highly nonlinear materials and structures under extreme loading conditions.展开更多
The finite volume method was applied to numerically simulate the bottom pressure field induced by regular waves,vehicles in calm water and vehicles in regular waves.The solution of Navier-Stokes(N-S)equations in the v...The finite volume method was applied to numerically simulate the bottom pressure field induced by regular waves,vehicles in calm water and vehicles in regular waves.The solution of Navier-Stokes(N-S)equations in the vicinity of numerical wave tank's boundary was forced towards the wave theoretical solution by incorporating momentum source terms,thereby reducing adverse effects such as wave reflection.Simulations utilizing laminar flow,turbulent flow,and ideal fluid models were all found capable of effectively capturing the waveform and bottom pressure of regular waves,agreeing well with experimental data.In predicting the bottom pressure field of the submerged vehicle,turbulent simulations considering fluid viscosity and boundary layer development provided more accurate predictions for the stern region than inviscid simulations.Due to sphere's diffractive effect,the sphere's bottom pressure field in waves is not a linear superposition of the wave's and the sphere's bottom pressure field.However,a slender submerged vehicle exhibits a weaker diffractive effect on waves,thus the submerged vehicle's bottom pressure field in waves can be approximated as a linear superposition of the wave's and the submerged vehicle's bottom pressure field,which simplifies computation and analysis.展开更多
A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization f...A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization factor(RF) is then employed to control the contribution made by the MD constraint in the cost function. Analysis results show that the RF can be taken as a combination of the step size and regularization parameter in the conventional NLMS. This implies that these parameters can be jointly controlled by simply tuning the RF as the proposed algorithm does. It also demonstrates that the RF can accelerate the convergence rate of the proposed algorithm and its optimal value can be obtained by minimizing the squared noise-free posteriori error. A method for automatically determining the value of the RF is also presented, which is free of any prior knowledge of the noise. While simulation results verify the analytical ones, it is also illustrated that the performance of the proposed algorithm is superior to the state-of-art ones in both the steady-state misalignment and the convergence rate. A novel algorithm is proposed to solve some problems. Simulation results show the effectiveness of the proposed algorithm.展开更多
Leader-following stationary consensus problem is investigated for the second-order multi-agent systems with timevarying communication delay and switching topology. Based on Lyapunov-Krasovskii functional and Lyapunov-...Leader-following stationary consensus problem is investigated for the second-order multi-agent systems with timevarying communication delay and switching topology. Based on Lyapunov-Krasovskii functional and Lyapunov-Razumikhin functions respectively, consensus criterions in the form of linear matrix inequality （LMI） are obtained for the system with time-varying communication delays under static interconnection topology con- verging to the leader＇s states. Moreover, the delay-dependent consensus criterion in the form of LMI is also obtained for the system with time-invariant communication delay and switching topologies by constructing Lyapunov-Krasovskii functional. Numerical simulations present the correctness of the results.展开更多
In order to avoid staircasing effect and preserve small scale texture information for the classical total variation regularization, a new minimization energy functional model for image decomposition is proposed. First...In order to avoid staircasing effect and preserve small scale texture information for the classical total variation regularization, a new minimization energy functional model for image decomposition is proposed. Firstly, an adaptive regularization based on the local feature of images is introduced to substitute total variational regularization. The oscillatory component containing texture and/or noise is modeled in generalized function space div （BMO）. And then, the existence and uniqueness of the minimizer for proposed model are proved. Finally, the gradient descent flow of the Euler-Lagrange equations for the new model is numerically implemented by using a finite difference method. Experiments show that the proposed model is very robust to noise, and the staircasing effect is avoided efficiently, while edges and textures are well remained.展开更多
This paper proposes second-order consensus protocols with time-delays and gives the measure of the robustness of the protocols to the time-delay existing in the network of agents with second-order dynamics. By employi...This paper proposes second-order consensus protocols with time-delays and gives the measure of the robustness of the protocols to the time-delay existing in the network of agents with second-order dynamics. By employing a frequency domain method, it is proven that the information states and their time derivatives of all the agents in the network achieve consensus asymptotically, respectively, for appropriate communication timedelay if the topology of weighted network is connected. Particularly, a tight upper bound on the communication time-delay that can be tolerated in the dynamic network is found. The consensus protocols are distributed in the sense that each agent only needs information from its neighboring agents, which reduces the complexity of connections between neighboring agents significantly. Numerical simulation results are provided to demonstrate the effectiveness and the sharpness of the theoretical results for second-order consensus in networks in the presence of communication time-delays.展开更多
The modelling of risky asset by stochastic processes with continuous paths, based on Brow- nian motions, suffers from several defects. First, the path continuity assumption does not seem reason- able in view of the po...The modelling of risky asset by stochastic processes with continuous paths, based on Brow- nian motions, suffers from several defects. First, the path continuity assumption does not seem reason- able in view of the possibility of sudden price variations （jumps） resulting of market crashes. A solution is to use stochastic processes with jumps, that will account for sudden variations of the asset prices. On the other hand, such jump models are generally based on the Poisson random measure. Many popular economic and financial models described by stochastic differential equations with Poisson jumps. This paper deals with the approximate controllability of a class of second-order neutral stochastic differential equations with infinite delay and Poisson jumps. By using the cosine family of operators, stochastic analysis techniques, a new set of sufficient conditions are derived for the approximate controllability of the above control system. An example is provided to illustrate the obtained theory.展开更多
The classical elastic impedance （EI） inversion method, however, is based on the L2-norm misfit function and considerably sensitive to outliers, assuming the noise of the seismic data to be the Guassian-distribution....The classical elastic impedance （EI） inversion method, however, is based on the L2-norm misfit function and considerably sensitive to outliers, assuming the noise of the seismic data to be the Guassian-distribution. So we have developed a more robust elastic impedance inversion based on the Ll-norm misfit function, and the noise is assumed to be non-Gaussian. Meanwhile, some regularization methods including the sparse constraint regularization and elastic impedance point constraint regularization are incorporated to improve the ill-posed characteristics of the seismic inversion problem. Firstly, we create the Ll-norm misfit objective function of pre-stack inversion problem based on the Bayesian scheme within the sparse constraint regularization and elastic impedance point constraint regularization. And then, we obtain more robust elastic impedances of different angles which are less sensitive to outliers in seismic data by using the IRLS strategy. Finally, we extract the P-wave and S-wave velocity and density by using the more stable parameter extraction method. Tests on synthetic data show that the P-wave and S-wave velocity and density parameters are still estimated reasonable with moderate noise. A test on the real data set shows that compared to the results of the classical elastic impedance inversion method, the estimated results using the proposed method can get better lateral continuity and more distinct show of the gas, verifying the feasibility and stability of the method.展开更多
A simple method for disturbance decoupling for matrix second-order linear systems is proposed directly in matrix second-order framework via Luenberger function observers based on complete parametric eigenstructure ass...A simple method for disturbance decoupling for matrix second-order linear systems is proposed directly in matrix second-order framework via Luenberger function observers based on complete parametric eigenstructure assignment. By introducing the H2 norm of the transfer function from disturbance to estimation error, sufficient and necessary conditions for disturbance decoupling in matrix second-order linear systems are established and are arranged into constraints on the design parameters via Luenberger function observers in terms of the closed-loop eigenvalues and the group of design parameters provided by the eigenstructure assignment approach. Therefore, the disturbance decoupling problem is converted into an eigenstructure assignment problem with extra parameter constraints. A simple example is investigated to show the effect and simplicity of the approach.展开更多
The presented iterative multiuser detection technique was based on joint deregularized and box-constrained solution to quadratic optimization with iterations similar to that used in the nonstationary Tikhonov iterated...The presented iterative multiuser detection technique was based on joint deregularized and box-constrained solution to quadratic optimization with iterations similar to that used in the nonstationary Tikhonov iterated algorithm.The deregularization maximized the energy of the solution,which was opposite to the Tikhonov regularization where the energy was minimized.However,combined with box-constraints,the deregularization forced the solution to be close to the binary set.It further exploited the box-constrained dichotomous coordinate descent algorithm and adapted it to the nonstationary iterative Tikhonov regularization to present an efficient detector.As a result,the worst-case and average complexity are reduced down as K2.8 and K2.5 floating point operation per second,respectively.The development improves the "efficient frontier" in multiuser detection,which is illustrated by simulation results.In addition,most operations in the detector are additions and bit-shifts.This makes the proposed technique attractive for fixed-point hardware implementation.展开更多
Tomographic synthetic aperture radar(TomoSAR)imaging exploits the antenna array measurements taken at different elevation aperture to recover the reflectivity function along the elevation direction.In these years,for ...Tomographic synthetic aperture radar(TomoSAR)imaging exploits the antenna array measurements taken at different elevation aperture to recover the reflectivity function along the elevation direction.In these years,for the sparse elevation distribution,compressive sensing(CS)is a developed favorable technique for the high-resolution elevation reconstruction in TomoSAR by solving an L_(1) regularization problem.However,because the elevation distribution in the forested area is nonsparse,if we want to use CS in the recovery,some basis,such as wavelet,should be exploited in the sparse L_(1/2) representation of the elevation reflectivity function.This paper presents a novel wavelet-based L_(2) regularization CS-TomoSAR imaging method of the forested area.In the proposed method,we first construct a wavelet basis,which can sparsely represent the elevation reflectivity function of the forested area,and then reconstruct the elevation distribution by using the L_(1/2) regularization technique.Compared to the wavelet-based L_(1) regularization TomoSAR imaging,the proposed method can improve the elevation recovered quality efficiently.展开更多
The main purpose of this research is the second-order modeling of flow and turbulent heat flux in nonpremixed methane-air combustion.A turbulent stream of non-premixed combustion in a stoichiometric condition,is numer...The main purpose of this research is the second-order modeling of flow and turbulent heat flux in nonpremixed methane-air combustion.A turbulent stream of non-premixed combustion in a stoichiometric condition,is numerically analyzed through the Reynolds averaged Navier-Stokes(RANS) equations.For modeling radiation and combustion,the discrete ordinates(DO) and eddy dissipation concept model have been applied.The Reynolds stress transport model(RSM) also was used for turbulence modeling.For THF in the energy equation,the GGDH model and high order algebraic model of HOGGDH with simple eddy diffusivity model have been applied.Comparing the numerical results of the SED model(with the turbulent Prandtl 0.85) and the second-order heat flux models with available experimental data follows that applying the second-order models significantly led to the modification of predicting temperature distribution and species mass fraction distribution in the combustion chamber.Calculation of turbulent Prandtl number in the combustion chamber shows that the assumption of Pr_(t) of 0.85 is far from reality and Pr_(t) in different areas varies from 0.4 to 1.2.展开更多
A novel rcgularization-based approach is presented for super-resolution reconstruction in order to achieve good tradeoff between noise removal and edge preservation. The method is developed by using L1 norm as data fi...A novel rcgularization-based approach is presented for super-resolution reconstruction in order to achieve good tradeoff between noise removal and edge preservation. The method is developed by using L1 norm as data fidelity term and anisotropic fourth-order diffusion model as a regularization item to constrain the smoothness of the reconstructed images. To evaluate and prove the performance of the proposed method, series of experiments and comparisons with some existing methods including bi-cubic interpolation method and bilateral total variation method are carried out. Numerical results on synthetic data show that the PSNR improvement of the proposed method is approximately 1.0906 dB on average compared to bilateral total variation method, and the results on real videos indicate that the proposed algorithm is also effective in terms of removing visual artifacts and preserving edges in restored images.展开更多
Aiming at the Four-Dimensional Variation source term inversion algorithm proposed earlier,the observation error regularization factor is introduced to improve the prediction accuracy of the diffusion model,and an impr...Aiming at the Four-Dimensional Variation source term inversion algorithm proposed earlier,the observation error regularization factor is introduced to improve the prediction accuracy of the diffusion model,and an improved Four-Dimensional Variation source term inversion algorithm with observation error regularization(OER-4DVAR STI model)is formed.Firstly,by constructing the inversion process and basic model of OER-4DVAR STI model,its basic principle and logical structure are studied.Secondly,the observation error regularization factor estimation method based on Bayesian optimization is proposed,and the error factor is separated and optimized by two parameters:error statistical time and deviation degree.Finally,the scientific,feasible and advanced nature of the OER-4DVAR STI model are verified by numerical simulation and tracer test data.The experimental results show that OER-4DVAR STI model can better reverse calculate the hazard source term information under the conditions of high atmospheric stability and flat underlying surface.Compared with the previous inversion algorithm,the source intensity estimation accuracy of OER-4DVAR STI model is improved by about 46.97%,and the source location estimation accuracy is improved by about 26.72%.展开更多
This paper discusses the regularization solution of ill posed equation with the help of its spectral decomposition formula. It shows that regularization can filter the influence of the high frequency errors which are ...This paper discusses the regularization solution of ill posed equation with the help of its spectral decomposition formula. It shows that regularization can filter the influence of the high frequency errors which are very sensitive to the parameters to be estimated, and gives a complete derivation of the spectral decomposition formulae of least squares adjustment, rank deficient adjustment and the regularization solution of ill posed equation. It also shows the equivalence between the trace of the mean squares error and the expectation of the secondnorm of estimated parameter’s total error.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.52475166,52175148)the Regional Collaboration Project of Shanxi Province(Grant No.202204041101044).
文摘Modern warfare demands weapons capable of penetrating substantial structures,which presents sig-nificant challenges to the reliability of the electronic devices that are crucial to the weapon's perfor-mance.Due to miniaturization of electronic components,it is challenging to directly measure or numerically predict the mechanical response of small-sized critical interconnections in board-level packaging structures to ensure the mechanical reliability of electronic devices in projectiles under harsh working conditions.To address this issue,an indirect measurement method using the Bayesian regularization-based load identification was proposed in this study based on finite element(FE)pre-dictions to estimate the load applied on critical interconnections of board-level packaging structures during the process of projectile penetration.For predicting the high-strain-rate penetration process,an FE model was established with elasto-plastic constitutive models of the representative packaging ma-terials(that is,solder material and epoxy molding compound)in which material constitutive parameters were calibrated against the experimental results by using the split-Hopkinson pressure bar.As the impact-induced dynamic bending of the printed circuit board resulted in an alternating tensile-compressive loading on the solder joints during penetration,the corner solder joints in the edge re-gions experience the highest S11 and strain,making them more prone to failure.Based on FE predictions at different structural scales,an improved Bayesian method based on augmented Tikhonov regulariza-tion was theoretically proposed to address the issues of ill-posed matrix inversion and noise sensitivity in the load identification at the critical solder joints.By incorporating a wavelet thresholding technique,the method resolves the problem of poor load identification accuracy at high noise levels.The proposed method achieves satisfactorily small relative errors and high correlation coefficients in identifying the mechanical response of local interconnections in board-level packaging structures,while significantly balancing the smoothness of response curves with the accuracy of peak identification.At medium and low noise levels,the relative error is less than 6%,while it is less than 10%at high noise levels.The proposed method provides an effective indirect approach for the boundary conditions of localized solder joints during the projectile penetration process,and its philosophy can be readily extended to other scenarios of multiscale analysis for highly nonlinear materials and structures under extreme loading conditions.
文摘The finite volume method was applied to numerically simulate the bottom pressure field induced by regular waves,vehicles in calm water and vehicles in regular waves.The solution of Navier-Stokes(N-S)equations in the vicinity of numerical wave tank's boundary was forced towards the wave theoretical solution by incorporating momentum source terms,thereby reducing adverse effects such as wave reflection.Simulations utilizing laminar flow,turbulent flow,and ideal fluid models were all found capable of effectively capturing the waveform and bottom pressure of regular waves,agreeing well with experimental data.In predicting the bottom pressure field of the submerged vehicle,turbulent simulations considering fluid viscosity and boundary layer development provided more accurate predictions for the stern region than inviscid simulations.Due to sphere's diffractive effect,the sphere's bottom pressure field in waves is not a linear superposition of the wave's and the sphere's bottom pressure field.However,a slender submerged vehicle exhibits a weaker diffractive effect on waves,thus the submerged vehicle's bottom pressure field in waves can be approximated as a linear superposition of the wave's and the submerged vehicle's bottom pressure field,which simplifies computation and analysis.
基金supported by the National Natural Science Foundation of China(61571131 11604055)
文摘A new normalized least mean square(NLMS) adaptive filter is first derived from a cost function, which incorporates the conventional one of the NLMS with a minimum-disturbance(MD)constraint. A variable regularization factor(RF) is then employed to control the contribution made by the MD constraint in the cost function. Analysis results show that the RF can be taken as a combination of the step size and regularization parameter in the conventional NLMS. This implies that these parameters can be jointly controlled by simply tuning the RF as the proposed algorithm does. It also demonstrates that the RF can accelerate the convergence rate of the proposed algorithm and its optimal value can be obtained by minimizing the squared noise-free posteriori error. A method for automatically determining the value of the RF is also presented, which is free of any prior knowledge of the noise. While simulation results verify the analytical ones, it is also illustrated that the performance of the proposed algorithm is superior to the state-of-art ones in both the steady-state misalignment and the convergence rate. A novel algorithm is proposed to solve some problems. Simulation results show the effectiveness of the proposed algorithm.
基金supported by the Fundamental Research Funds for the Central Universities(JUSRP11020)the Specialized Research Fund for the Doctoral Program of Higher Education of China(20090093120006)
文摘Leader-following stationary consensus problem is investigated for the second-order multi-agent systems with timevarying communication delay and switching topology. Based on Lyapunov-Krasovskii functional and Lyapunov-Razumikhin functions respectively, consensus criterions in the form of linear matrix inequality （LMI） are obtained for the system with time-varying communication delays under static interconnection topology con- verging to the leader＇s states. Moreover, the delay-dependent consensus criterion in the form of LMI is also obtained for the system with time-invariant communication delay and switching topologies by constructing Lyapunov-Krasovskii functional. Numerical simulations present the correctness of the results.
基金supported by the Science and Technology Foundation Program of Chongqing Municipal Education Committee (KJ091208)
文摘In order to avoid staircasing effect and preserve small scale texture information for the classical total variation regularization, a new minimization energy functional model for image decomposition is proposed. Firstly, an adaptive regularization based on the local feature of images is introduced to substitute total variational regularization. The oscillatory component containing texture and/or noise is modeled in generalized function space div （BMO）. And then, the existence and uniqueness of the minimizer for proposed model are proved. Finally, the gradient descent flow of the Euler-Lagrange equations for the new model is numerically implemented by using a finite difference method. Experiments show that the proposed model is very robust to noise, and the staircasing effect is avoided efficiently, while edges and textures are well remained.
基金supported by the National Natural Science Foundation of China (6057408860274014)
文摘This paper proposes second-order consensus protocols with time-delays and gives the measure of the robustness of the protocols to the time-delay existing in the network of agents with second-order dynamics. By employing a frequency domain method, it is proven that the information states and their time derivatives of all the agents in the network achieve consensus asymptotically, respectively, for appropriate communication timedelay if the topology of weighted network is connected. Particularly, a tight upper bound on the communication time-delay that can be tolerated in the dynamic network is found. The consensus protocols are distributed in the sense that each agent only needs information from its neighboring agents, which reduces the complexity of connections between neighboring agents significantly. Numerical simulation results are provided to demonstrate the effectiveness and the sharpness of the theoretical results for second-order consensus in networks in the presence of communication time-delays.
基金supported by the National Board for Higher Mathematics,Mumbai,India under Grant No.2/48(5)/2013/NBHM(R.P.)/RD-II/688 dt 16.01.2014
文摘The modelling of risky asset by stochastic processes with continuous paths, based on Brow- nian motions, suffers from several defects. First, the path continuity assumption does not seem reason- able in view of the possibility of sudden price variations （jumps） resulting of market crashes. A solution is to use stochastic processes with jumps, that will account for sudden variations of the asset prices. On the other hand, such jump models are generally based on the Poisson random measure. Many popular economic and financial models described by stochastic differential equations with Poisson jumps. This paper deals with the approximate controllability of a class of second-order neutral stochastic differential equations with infinite delay and Poisson jumps. By using the cosine family of operators, stochastic analysis techniques, a new set of sufficient conditions are derived for the approximate controllability of the above control system. An example is provided to illustrate the obtained theory.
基金Projects(U1562215,41674130,41404088)supported by the National Natural Science Foundation of ChinaProjects(2013CB228604,2014CB239201)supported by the National Basic Research Program of China+1 种基金Projects(2016ZX05027004-001,2016ZX05002006-009)supported by the National Oil and Gas Major Projects of ChinaProject(15CX08002A)supported by the Fundamental Research Funds for the Central Universities,China
文摘The classical elastic impedance （EI） inversion method, however, is based on the L2-norm misfit function and considerably sensitive to outliers, assuming the noise of the seismic data to be the Guassian-distribution. So we have developed a more robust elastic impedance inversion based on the Ll-norm misfit function, and the noise is assumed to be non-Gaussian. Meanwhile, some regularization methods including the sparse constraint regularization and elastic impedance point constraint regularization are incorporated to improve the ill-posed characteristics of the seismic inversion problem. Firstly, we create the Ll-norm misfit objective function of pre-stack inversion problem based on the Bayesian scheme within the sparse constraint regularization and elastic impedance point constraint regularization. And then, we obtain more robust elastic impedances of different angles which are less sensitive to outliers in seismic data by using the IRLS strategy. Finally, we extract the P-wave and S-wave velocity and density by using the more stable parameter extraction method. Tests on synthetic data show that the P-wave and S-wave velocity and density parameters are still estimated reasonable with moderate noise. A test on the real data set shows that compared to the results of the classical elastic impedance inversion method, the estimated results using the proposed method can get better lateral continuity and more distinct show of the gas, verifying the feasibility and stability of the method.
文摘A simple method for disturbance decoupling for matrix second-order linear systems is proposed directly in matrix second-order framework via Luenberger function observers based on complete parametric eigenstructure assignment. By introducing the H2 norm of the transfer function from disturbance to estimation error, sufficient and necessary conditions for disturbance decoupling in matrix second-order linear systems are established and are arranged into constraints on the design parameters via Luenberger function observers in terms of the closed-loop eigenvalues and the group of design parameters provided by the eigenstructure assignment approach. Therefore, the disturbance decoupling problem is converted into an eigenstructure assignment problem with extra parameter constraints. A simple example is investigated to show the effect and simplicity of the approach.
文摘The presented iterative multiuser detection technique was based on joint deregularized and box-constrained solution to quadratic optimization with iterations similar to that used in the nonstationary Tikhonov iterated algorithm.The deregularization maximized the energy of the solution,which was opposite to the Tikhonov regularization where the energy was minimized.However,combined with box-constraints,the deregularization forced the solution to be close to the binary set.It further exploited the box-constrained dichotomous coordinate descent algorithm and adapted it to the nonstationary iterative Tikhonov regularization to present an efficient detector.As a result,the worst-case and average complexity are reduced down as K2.8 and K2.5 floating point operation per second,respectively.The development improves the "efficient frontier" in multiuser detection,which is illustrated by simulation results.In addition,most operations in the detector are additions and bit-shifts.This makes the proposed technique attractive for fixed-point hardware implementation.
基金This work was supported by the Fundamental Research Funds for the Central Universities(NE2020004)the National Natural Science Foundation of China(61901213)+3 种基金the Natural Science Foundation of Jiangsu Province(BK20190397)the Aeronautical Science Foundation of China(201920052001)the Young Science and Technology Talent Support Project of Jiangsu Science and Technology Associationthe Foundation of Graduate Innovation Center in Nanjing University of Aeronautics and Astronautics(kfjj20200419).
文摘Tomographic synthetic aperture radar(TomoSAR)imaging exploits the antenna array measurements taken at different elevation aperture to recover the reflectivity function along the elevation direction.In these years,for the sparse elevation distribution,compressive sensing(CS)is a developed favorable technique for the high-resolution elevation reconstruction in TomoSAR by solving an L_(1) regularization problem.However,because the elevation distribution in the forested area is nonsparse,if we want to use CS in the recovery,some basis,such as wavelet,should be exploited in the sparse L_(1/2) representation of the elevation reflectivity function.This paper presents a novel wavelet-based L_(2) regularization CS-TomoSAR imaging method of the forested area.In the proposed method,we first construct a wavelet basis,which can sparsely represent the elevation reflectivity function of the forested area,and then reconstruct the elevation distribution by using the L_(1/2) regularization technique.Compared to the wavelet-based L_(1) regularization TomoSAR imaging,the proposed method can improve the elevation recovered quality efficiently.
文摘The main purpose of this research is the second-order modeling of flow and turbulent heat flux in nonpremixed methane-air combustion.A turbulent stream of non-premixed combustion in a stoichiometric condition,is numerically analyzed through the Reynolds averaged Navier-Stokes(RANS) equations.For modeling radiation and combustion,the discrete ordinates(DO) and eddy dissipation concept model have been applied.The Reynolds stress transport model(RSM) also was used for turbulence modeling.For THF in the energy equation,the GGDH model and high order algebraic model of HOGGDH with simple eddy diffusivity model have been applied.Comparing the numerical results of the SED model(with the turbulent Prandtl 0.85) and the second-order heat flux models with available experimental data follows that applying the second-order models significantly led to the modification of predicting temperature distribution and species mass fraction distribution in the combustion chamber.Calculation of turbulent Prandtl number in the combustion chamber shows that the assumption of Pr_(t) of 0.85 is far from reality and Pr_(t) in different areas varies from 0.4 to 1.2.
基金Projects(60963012,61262034)supported by the National Natural Science Foundation of ChinaProject(211087)supported by the Key Project of Ministry of Education of ChinaProjects(2010GZS0052,20114BAB211020)supported by the Natural Science Foundation of Jiangxi Province,China
文摘A novel rcgularization-based approach is presented for super-resolution reconstruction in order to achieve good tradeoff between noise removal and edge preservation. The method is developed by using L1 norm as data fidelity term and anisotropic fourth-order diffusion model as a regularization item to constrain the smoothness of the reconstructed images. To evaluate and prove the performance of the proposed method, series of experiments and comparisons with some existing methods including bi-cubic interpolation method and bilateral total variation method are carried out. Numerical results on synthetic data show that the PSNR improvement of the proposed method is approximately 1.0906 dB on average compared to bilateral total variation method, and the results on real videos indicate that the proposed algorithm is also effective in terms of removing visual artifacts and preserving edges in restored images.
基金Ministry of Science and Technology of the People’s Republic of China for its support and guidance(Grant No.2018YFC0214100)。
文摘Aiming at the Four-Dimensional Variation source term inversion algorithm proposed earlier,the observation error regularization factor is introduced to improve the prediction accuracy of the diffusion model,and an improved Four-Dimensional Variation source term inversion algorithm with observation error regularization(OER-4DVAR STI model)is formed.Firstly,by constructing the inversion process and basic model of OER-4DVAR STI model,its basic principle and logical structure are studied.Secondly,the observation error regularization factor estimation method based on Bayesian optimization is proposed,and the error factor is separated and optimized by two parameters:error statistical time and deviation degree.Finally,the scientific,feasible and advanced nature of the OER-4DVAR STI model are verified by numerical simulation and tracer test data.The experimental results show that OER-4DVAR STI model can better reverse calculate the hazard source term information under the conditions of high atmospheric stability and flat underlying surface.Compared with the previous inversion algorithm,the source intensity estimation accuracy of OER-4DVAR STI model is improved by about 46.97%,and the source location estimation accuracy is improved by about 26.72%.
文摘This paper discusses the regularization solution of ill posed equation with the help of its spectral decomposition formula. It shows that regularization can filter the influence of the high frequency errors which are very sensitive to the parameters to be estimated, and gives a complete derivation of the spectral decomposition formulae of least squares adjustment, rank deficient adjustment and the regularization solution of ill posed equation. It also shows the equivalence between the trace of the mean squares error and the expectation of the secondnorm of estimated parameter’s total error.
