A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted...A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted in a 1.3 m3tank and a 113 m3bunker.The blast parameters,including the quasistatic pressure(ΔpQS),special impulse(I),and peak overpressure(Δpmax),and images of the explosion process were recorded,and the influence of the Al content(30% and 50%) and Al particle size(1,10,and 50 μm) on the energy release of aluminum/rubber composites were investigated.The results revealed that the use of an active layer increased the peak overpressure generated by the primary blast wave,as well as the quasistatic pressure and special impulse related to fuel burning within tens of milliseconds after detonation.When the Al content was increased from 30% to 50%,the increases of ΔpQS and I were not obvious,and Δpmaxeven decreased,possibly because of decreased combustion efficiency and greater absorption of the blast wave energy for layers with 50% Al.Compared with the pure JH-2charge,the charge with 1 μm Al particles produced the highest Δpmax,indicating that better transient blast performance was generated by smaller Al particles.However,the charge with 10 μm Al particles showed the largest ΔpQSand I,suggesting that a stronger destructive effect occurred over a longer duration for charges that contained moderate 10 μm Al.展开更多
Boron has high mass and volume calorific values,but it is difficult to ignite and has low combustion efficiency.This literature review summarizes the strategies that are used to solve the above-mentioned problems,whic...Boron has high mass and volume calorific values,but it is difficult to ignite and has low combustion efficiency.This literature review summarizes the strategies that are used to solve the above-mentioned problems,which include coatings of boron by using fluoride compounds,energetic composites,metal fuels,and metal oxides.Coating techniques include recrystallization,dual-solvent,phase transfer,electrospinning,etc.As one of the effective coating agents,the fluorine compounds can react with the oxide shell of boron powder.In comparison,the energetic composites can effectively improve the flame temperature of boron powder and enhance the evaporation efficiency of oxide film as a condensed product.Metals and metal oxides would react with boron powder to form metal borides with a lower ignition point,which could reduce its ignition temperature.展开更多
Metal matrix composites tiles based on Ti-6Al-4V(Ti64)alloy,reinforced with 10,20,and 40(vol%)of either TiC or TiB particles were made using press-and-sinter blended elemental powder metallurgy(BEPM)and then bonded to...Metal matrix composites tiles based on Ti-6Al-4V(Ti64)alloy,reinforced with 10,20,and 40(vol%)of either TiC or TiB particles were made using press-and-sinter blended elemental powder metallurgy(BEPM)and then bonded together into 3-layer laminated plates using hot isostatic pressing(HIP).The laminates were ballistically tested and demonstrated superior performance.The microstructure and properties of the laminates were analyzed to determine the effect of the BEPM and HIP processing on the ballistic properties of the layered plates.The effect of porosity in sintered composites on further diffusion bonding of the plates during HIP is analyzed to understand the bonding features at the interfaces between different adjacent layers in the laminate.Exceptional ballistic performance of fabricated structures was explained by a significant reduction in the residual porosity of the BEPM products by their additional processing using HIP,which provides an unprecedented increase in the hardness of the layered composites.It is argued that the combination of the used two technologies,BEPM and HIP is principally complimentary for the materials in question with the abilities to solve the essential problems of each used individually.展开更多
INADEQUATE(Incredible Natural Abundance DoublE QUAntum Transfer Experiment)is one of the most important techniques in revealing the carbon skeleton of organic solids in solid-state NMR spectroscopy.Nevertheless,its us...INADEQUATE(Incredible Natural Abundance DoublE QUAntum Transfer Experiment)is one of the most important techniques in revealing the carbon skeleton of organic solids in solid-state NMR spectroscopy.Nevertheless,its use for structural analysis is quite limited due to the low natural abundance of^(13)C-^(13)C connectivity(~0.01%)and thus low sensitivity.Particularly,in semi-solids like rubbers,the sensitivity will be further significantly reduced by the inefficient cross polarization from 1H to^(13)C due to molecular motions induced averaging of^(1)H-^(13)C dipolar couplings.Herein,in this study,we demonstrate that transient nuclear Overhauser effect(NOE)can be used to efficiently enhance^(13)C signals,and thus enable rapid acquisition of two-dimensional(2D)^(13)C INADEQUATE spectra of rubbers.Using chlorobutyl rubber as the model system,it is found that an overall signalto-noise ratio(SNR)enhancement about 22%can be achieved,leading to significant timesaving by about 33%as compared to the direct polarization-based INADEQUATE experiment.Further experimental results on natural rubber and ethylene propylene diene monomer(EPDM)rubber are also shown to demonstrate the robust performance of transient NOE enhanced INADEQUATE experiment.展开更多
As an energetic material of great interest,the work capacity of dihydroxylammonium 5,5’-bistetrazole-1,1’-diolate(TKX-50)has been questioned recently.Although some research groups have explored the reasons for the l...As an energetic material of great interest,the work capacity of dihydroxylammonium 5,5’-bistetrazole-1,1’-diolate(TKX-50)has been questioned recently.Although some research groups have explored the reasons for the low working ability of TKX-50,the plane impact experiment on powdered TKX-50 is obviously closer to the practical application,and the conclusions based on this are more guiding.Hence,we performed shock Hugoniot measurements of powdered TKX-50 between 5.65 and 16.29 GPa.The plane impact experiments of powdered TKX-50 were carried out and the shocked Raman spectra were collected.By Raman spectroscopy analysis,a new peak of powdered TKX-50 was found between19.47 GPa and 24.96 GPa,which may be caused by decomposition/phase transition and was related with the low work capacity.展开更多
A feedback control of fuel recycling via real-time boron powder injection,addressing the issue of continuously increasing recycling in long-pulse plasma discharges,has been successfully developed and implemented on EA...A feedback control of fuel recycling via real-time boron powder injection,addressing the issue of continuously increasing recycling in long-pulse plasma discharges,has been successfully developed and implemented on EAST tokamak.The feedback control system includes four main parts:the impurity powder dropper(IPD),a diagnostic system measuring fuel recycling level represented by D_(α)emission,a plasma control system(PCS)implementing the Proportional Integral Derivative(PID)algorithm,and a signal converter connecting the IPD and PCS.Based on this control system,both active control and feedback control experiments have recently been performed on EAST with a full metal wall.The experimental results show that the fuel recycling can be gradually reduced to lower level as PCS control voltage increases.In the feedback control experiments,it is also observed that the D_(α)emission is reduced to the level below the target D_(α)value by adjusting boron injection flow rate,indicating successful implementation of the fuel recycling feedback control on EAST.This technique provides a new method for fuel recycling control of long pulse and high parameter plasma operations in future fusion devices.展开更多
Diarrhea has become the leading cause of illness and death among infants and young children in developing countries.Clinically,patients with diarrhea showed damaged intestinal epithelial villi,usually accompanied by l...Diarrhea has become the leading cause of illness and death among infants and young children in developing countries.Clinically,patients with diarrhea showed damaged intestinal epithelial villi,usually accompanied by lactase deficiency.In this study,we evaluated the therapeutic effects of lactose-free milk powder on rats and children with diarrhea.Antibiotic-associated diarrhea(AAD)model was established by gavage with antibiotic mixture in SD rats,followed by administration of milk powder containing lactose or not.The results showed that lactose-free milk powder ameliorated A AD-related diarrhea symptoms,and accelerated the recovery from diarrhea.And 16S sequencing results indicated lactose-free milk powder contributed to increase theα-andβ-diversity of intestinal flora,and restore the intestinal microbiota disorder.In conclusion,our data demonstrate that lactose-free milk powder could alleviate diarrhea by restoring gut microbiota and intestinal barrier function.展开更多
Nanorubber/epoxy composites containing 0,2,6 and 10 wt%nanorubber are subjected to uniaxial compression over a wide range of strain rate from 8×10^(-4) s^(-1) to~2×10^(4) s^(-1).Unexpectedly,their strain rat...Nanorubber/epoxy composites containing 0,2,6 and 10 wt%nanorubber are subjected to uniaxial compression over a wide range of strain rate from 8×10^(-4) s^(-1) to~2×10^(4) s^(-1).Unexpectedly,their strain rate sensitivity and strain hardening index increase with increasing nanorubber content.Potential mechanisms are proposed based on numerical simulations using a unit cell model.An increase in the strain rate sensitivity with increasing nanorubber content results from the fact that the nanorubber becomes less incompressible at high strain,generating a higher hydro-static pressure.Adiabatic shear localization starts to occur in the epoxy under a strain rate of 22,000 s^(-1) when the strain exceeds 0.35.The presence of nanorubber in the epoxy reduces adiabatic shear localization by preventing it from propagating.展开更多
Zn powder anodes have attracted much attention in aqueous Zn ion battery applications due to advantages such as low cost and processability.However,the high-activity Zn powder anode faces problems such as side reactio...Zn powder anodes have attracted much attention in aqueous Zn ion battery applications due to advantages such as low cost and processability.However,the high-activity Zn powder anode faces problems such as side reactions,hydrogen evolution,and dendrites,which limit the cycling stability of the cell.In this work,the high activity of Zn powder is weakened by introducing low-cost erythritol as a functional additive in the ZnSO_(4) electrolyte to improve the cycle life of the cell.Both theoretical calculations and empirical evidence demonstrate that the incorporation of erythritol alters the coordination sphere of Zn^(2+)and modifies the local molecular architecture of the electrolyte.This modification serves to diminish the reactivity of water molecules,thereby efficaciously suppressing dendrite formation and deleterious ancillary reactions on the zinc powder anode surfaces.Concurrently,erythritol functions as an interfacial cationic captor,enhancing reaction dynamics and facilitating the development of a favorable protective layer throughout the zinc plating/stripping process.Consequently,the symmetric cell paired with an erythritol-containing electrolyte manifests stable cycling performance for an extended duration of 850 h at a current density of 0.288 mA cm^(-2)and areal capacity of 0.144 mAh cm^(-2).Notably,it maintains a cycling life of 400 h even under intensified conditions (2.88 mA cm^(-2)/1.44 mA h cm^(-2)).Furthermore,the constructed Na_(2)V_(6)O_(16)·3H_(2)O full cell illustrated remarkable capacity retention of 155.8 mA h g^(-1)following 800 cycles at a high rate of 5 A g^(-1).展开更多
The environmental hazards and"carbon footprint"of oil and gas drilling can be significantly reduced by replacing traditional petroleum-based chemical additives with natural materials derived from plants and ...The environmental hazards and"carbon footprint"of oil and gas drilling can be significantly reduced by replacing traditional petroleum-based chemical additives with natural materials derived from plants and animals.This paper explored for the first time the interaction mechanism between natural rubber latex(NRL)and bentonite suspensions(BTs)through a series of characterization experiments,as well as the potential applications in water-based drilling fluids(WBDF).The gel viscoelasticity experiments showed that NRL could decrease the consistency coefficient(k)and flow index(n)of BTs,and enhance the shear thinning performance of BTs as pseudo-plastic fluids.In addition,0.5 w/v%NRL not only increased the critical yield stress and strengthened the structural strength between the bentonite particles,but also facilitated the compatibility of pressure loss and flow efficiency.The evaluation of colloidal stability and WBDF performance indicated that NRL particles could promote the hydration and charge stability on the surface of BTs particles,and optimize the particle size distribution and flow resistance of WBDF under the"intercalation-exfoliation-encapsulation"synergistic interaction.Moreover,NRL can improve the rheological properties of WBDF at high temperatures(<150.C),and form a dense blocking layer by bridging and sealing the pores and cracks of the filter cake,which ultimately reduces the permeability of the cake and the filtration loss of WBDF.展开更多
In the Large Helical Device(LHD),diborane(B2H6)is used as a standard boron source for boronization,which is assisted by helium glow discharges.In 2019,a new Impurity Powder Dropper(IPD)system was installed and is unde...In the Large Helical Device(LHD),diborane(B2H6)is used as a standard boron source for boronization,which is assisted by helium glow discharges.In 2019,a new Impurity Powder Dropper(IPD)system was installed and is under evaluation as a real-time wall conditioning technique.In the LHD,which is a large-sized heliotron device,an additional helium(He)glow discharge cleaning(GDC)after boronization was operated for a reduction in hydrogen recycling from the coated boron layers.This operational time of 3 h was determined by spectroscopic data during glow discharges.A flat hydrogen profile is obtained on the top surface of the coated boron on the specimen exposed to boronization.The results suggest a reduction in hydrogen at the top surface by He-GDC.Trapped oxygen in coated boron was obtained by boronization,and the coated boron,which has boron-oxide,on the first wall by B-IPD was also shown.Considering the difference in coating areas between B2H6 boronization and B-IPD operation,it would be most effective to use the IPD and B2H6 boronization coating together for optimized wall conditioning.展开更多
Solid waste recycling is an economically sound strategy for preserving the environment,safeguarding natural resources,and diminishing the reliance on raw material consumption.Geopolymer technology offers a significant...Solid waste recycling is an economically sound strategy for preserving the environment,safeguarding natural resources,and diminishing the reliance on raw material consumption.Geopolymer technology offers a significant advantage by enabling the reuse and recycling of diverse materials.This research assesses how including silica fume and glass powder enhances the impact resistance of ultra-high-performance geopolymer concrete(UHPGC).In total,18 distinct mixtures were formulated by substituting ground granulated blast furnace slag with varying proportions of silica fume and glass powder,ranging from 10%to 40%.Similarly,for each of the mixtures above,steel fibre was added at a dosage of 1.5%to address the inherent brittleness of UHPGC.The mixtures were activated by combining sodium hydroxide and sodium silicate solution to generate geopolymer binders.The specimens were subjected to drop-weight impact testing,wherein an examination was carried out to evaluate various parameters,including flowability,density at fresh and hardened state,compressive strength,impact numbers indicative of cracking and failure occurrences,ductility index,and analysis of failure modes.Additionally,the variations in the impact test outcomes were analyzed using the Weibull distribution,and the findings corresponding to survival probability were offered.Furthermore,the microstructure of UHPGC was scrutinized through scanning electron microscopy.Findings reveal that the specimens incorporating glass powder exhibited lower cracking impact number values than those utilizing silica fume,with reductions ranging from 18.63%to 34.31%.Similarly,failure impact number values decreased from 8.26%to 28.46%across glass powder contents.The maximum compressive and impact strength was recorded in UHPGC,comprising 10%silica fume with fibres.展开更多
Elastomer blends,among which natural rubber(NR)and butadiene rubber(BR),are involved in many components of the automotive/tire industry.A comprehensive understanding of their mechanical behavior requires,among other f...Elastomer blends,among which natural rubber(NR)and butadiene rubber(BR),are involved in many components of the automotive/tire industry.A comprehensive understanding of their mechanical behavior requires,among other features,a detailed description of the crosslink density in these mixtures.In the case of vulcanized immiscible blends,the distribution of the cross-link density within each of the NR-and BR-rich domains is key information,but difficult to determine using the conventional approaches used for one-component crosslinked elastomers.In this study,the vulcanization within NR/BR blends is investigated using a robust^(1)H double-quantum(DQ)MAS recoupling experiment,BaBa-xy16.Two kinds of cross-linked NR/BR blends were considered with two different microstructures for the BR component.The bulk organization of the resulting blends was first probed by analyzing the^(1)H spin-lattice relaxation behavior.In a second step,BaBa-xy16 was used to investigate,in a selective way,the cross-link heterogeneities within NR/BR blends.In particular,for immiscible NR/BR mixtures,the distribution of the cross-link density between both phases was compared and the observed differences were discussed.展开更多
A novel design of micro-aluminum(μAl)powder coated with bi-/tri-component alloy layer,such as:Ni-P and Ni-P-Cu(namely,Al@Ni-P,Al@Ni-P-Cu,respectively),as combustion catalysts,were introduced to release its huge energ...A novel design of micro-aluminum(μAl)powder coated with bi-/tri-component alloy layer,such as:Ni-P and Ni-P-Cu(namely,Al@Ni-P,Al@Ni-P-Cu,respectively),as combustion catalysts,were introduced to release its huge energy inside Al-core and promote rapid pyrolysis of ammonium perchlorate(AP)at a lower temperature in aluminized propellants.The microstructure of Al@Ni-P-Cu demonstrates that a three-layer Ni-P-Cu shell,with the thickness of~100 nm,is uniformly supported byμAl carrier(fuel unit),which has an amorphous surface with a thickness of~2.3 nm(catalytic unit).The peak temperature of AP with the addition of Al@Ni-P-Cu(3.5%)could significantly drop to 316.2℃ at high-temperature thermal decomposition,reduced by 124.3℃,in comparison to that of pure AP with 440.5℃.It illustrated that the introduction of Al@Ni-P-Cu could weaken or even eliminate the obstacle of AP pyrolysis due to its reduction of activation energy with 118.28 kJ/mol.The laser ignition results showed that the ignition delay time of Al@Ni-P-Cu/AP mixture with 78 ms in air is shorter than that of Al@Ni-P/AP(118 ms),decreased by 33.90%.Those astonishing breakthroughs were attributed to the synergistic effects of adequate active sites on amorphous surface and oxidation exothermic reactions(7597.7 J/g)of Al@Ni-P-Cu,resulting in accelerated mass and/or heat transfer rate to catalyze AP pyrolysis and combustion.Moreover,it is believed to provide an alternative Al-based combustion catalyst for propellant designer,to promote the development the propellants toward a higher energy.展开更多
基金funded by the National Natural Science Foundation of China(Grant No.11972018)the Defense Pre-Research Joint Foundation of Chinese Ordnance Industry(Grant No.6141B012858)。
文摘A layered charge composed of the JH-2 explosive enveloped by a thick-walled cylindrical casing(active aluminum/rubber and inert lithium fluoride/rubber composites) was designed and explosion experiments were conducted in a 1.3 m3tank and a 113 m3bunker.The blast parameters,including the quasistatic pressure(ΔpQS),special impulse(I),and peak overpressure(Δpmax),and images of the explosion process were recorded,and the influence of the Al content(30% and 50%) and Al particle size(1,10,and 50 μm) on the energy release of aluminum/rubber composites were investigated.The results revealed that the use of an active layer increased the peak overpressure generated by the primary blast wave,as well as the quasistatic pressure and special impulse related to fuel burning within tens of milliseconds after detonation.When the Al content was increased from 30% to 50%,the increases of ΔpQS and I were not obvious,and Δpmaxeven decreased,possibly because of decreased combustion efficiency and greater absorption of the blast wave energy for layers with 50% Al.Compared with the pure JH-2charge,the charge with 1 μm Al particles produced the highest Δpmax,indicating that better transient blast performance was generated by smaller Al particles.However,the charge with 10 μm Al particles showed the largest ΔpQSand I,suggesting that a stronger destructive effect occurred over a longer duration for charges that contained moderate 10 μm Al.
基金funded by Shaanxi Provincial Key Research and Development Program of China(Grant No.2021ZDLGY11)partially supported by NSAF Project of China(Grant No.U2030202)。
文摘Boron has high mass and volume calorific values,but it is difficult to ignite and has low combustion efficiency.This literature review summarizes the strategies that are used to solve the above-mentioned problems,which include coatings of boron by using fluoride compounds,energetic composites,metal fuels,and metal oxides.Coating techniques include recrystallization,dual-solvent,phase transfer,electrospinning,etc.As one of the effective coating agents,the fluorine compounds can react with the oxide shell of boron powder.In comparison,the energetic composites can effectively improve the flame temperature of boron powder and enhance the evaporation efficiency of oxide film as a condensed product.Metals and metal oxides would react with boron powder to form metal borides with a lower ignition point,which could reduce its ignition temperature.
基金funding from the NATO Agency Science for Peace and Security (#G5787)Ballistic investigations were co-financed by Military University of Technology in Warsaw under research project UGB 829/2023/WATSeparate works made in G.V.Kurdyumov Institute for Metal Physics of N.A.S.of Ukraine were partially financially supported by N.A.S.of Ukraine within the frames of project#III09-18。
文摘Metal matrix composites tiles based on Ti-6Al-4V(Ti64)alloy,reinforced with 10,20,and 40(vol%)of either TiC or TiB particles were made using press-and-sinter blended elemental powder metallurgy(BEPM)and then bonded together into 3-layer laminated plates using hot isostatic pressing(HIP).The laminates were ballistically tested and demonstrated superior performance.The microstructure and properties of the laminates were analyzed to determine the effect of the BEPM and HIP processing on the ballistic properties of the layered plates.The effect of porosity in sintered composites on further diffusion bonding of the plates during HIP is analyzed to understand the bonding features at the interfaces between different adjacent layers in the laminate.Exceptional ballistic performance of fabricated structures was explained by a significant reduction in the residual porosity of the BEPM products by their additional processing using HIP,which provides an unprecedented increase in the hardness of the layered composites.It is argued that the combination of the used two technologies,BEPM and HIP is principally complimentary for the materials in question with the abilities to solve the essential problems of each used individually.
基金support of National Natural Science Foundation of China(No.22173033,and 22241501)Natural Science Foundation of Guangdong Province,China(No.2023A1515011395).
文摘INADEQUATE(Incredible Natural Abundance DoublE QUAntum Transfer Experiment)is one of the most important techniques in revealing the carbon skeleton of organic solids in solid-state NMR spectroscopy.Nevertheless,its use for structural analysis is quite limited due to the low natural abundance of^(13)C-^(13)C connectivity(~0.01%)and thus low sensitivity.Particularly,in semi-solids like rubbers,the sensitivity will be further significantly reduced by the inefficient cross polarization from 1H to^(13)C due to molecular motions induced averaging of^(1)H-^(13)C dipolar couplings.Herein,in this study,we demonstrate that transient nuclear Overhauser effect(NOE)can be used to efficiently enhance^(13)C signals,and thus enable rapid acquisition of two-dimensional(2D)^(13)C INADEQUATE spectra of rubbers.Using chlorobutyl rubber as the model system,it is found that an overall signalto-noise ratio(SNR)enhancement about 22%can be achieved,leading to significant timesaving by about 33%as compared to the direct polarization-based INADEQUATE experiment.Further experimental results on natural rubber and ethylene propylene diene monomer(EPDM)rubber are also shown to demonstrate the robust performance of transient NOE enhanced INADEQUATE experiment.
基金supported by the National Natural Science Foundation of China(Grant No.12072299)the Fundamental Research Funds for the Central Universities(Grant No.2682020ZT102)。
文摘As an energetic material of great interest,the work capacity of dihydroxylammonium 5,5’-bistetrazole-1,1’-diolate(TKX-50)has been questioned recently.Although some research groups have explored the reasons for the low working ability of TKX-50,the plane impact experiment on powdered TKX-50 is obviously closer to the practical application,and the conclusions based on this are more guiding.Hence,we performed shock Hugoniot measurements of powdered TKX-50 between 5.65 and 16.29 GPa.The plane impact experiments of powdered TKX-50 were carried out and the shocked Raman spectra were collected.By Raman spectroscopy analysis,a new peak of powdered TKX-50 was found between19.47 GPa and 24.96 GPa,which may be caused by decomposition/phase transition and was related with the low work capacity.
基金funded by the National Key Research and Development Program of China(Nos.2022YFE03130000 and 2022YFE03130003)National Natural Science Foundation of China(Nos.12205336 and 12475208)+2 种基金The Strategic Priority Research Program of Chinese Academy of Sciences(No.XDB0790102)the Provincial Natural Science Foundation of Anhui(No.2408085J002)Interdisciplinary and Collaborative Teams of CAS。
文摘A feedback control of fuel recycling via real-time boron powder injection,addressing the issue of continuously increasing recycling in long-pulse plasma discharges,has been successfully developed and implemented on EAST tokamak.The feedback control system includes four main parts:the impurity powder dropper(IPD),a diagnostic system measuring fuel recycling level represented by D_(α)emission,a plasma control system(PCS)implementing the Proportional Integral Derivative(PID)algorithm,and a signal converter connecting the IPD and PCS.Based on this control system,both active control and feedback control experiments have recently been performed on EAST with a full metal wall.The experimental results show that the fuel recycling can be gradually reduced to lower level as PCS control voltage increases.In the feedback control experiments,it is also observed that the D_(α)emission is reduced to the level below the target D_(α)value by adjusting boron injection flow rate,indicating successful implementation of the fuel recycling feedback control on EAST.This technique provides a new method for fuel recycling control of long pulse and high parameter plasma operations in future fusion devices.
基金supported by the project of two children’s dairy products (201704810610483)。
文摘Diarrhea has become the leading cause of illness and death among infants and young children in developing countries.Clinically,patients with diarrhea showed damaged intestinal epithelial villi,usually accompanied by lactase deficiency.In this study,we evaluated the therapeutic effects of lactose-free milk powder on rats and children with diarrhea.Antibiotic-associated diarrhea(AAD)model was established by gavage with antibiotic mixture in SD rats,followed by administration of milk powder containing lactose or not.The results showed that lactose-free milk powder ameliorated A AD-related diarrhea symptoms,and accelerated the recovery from diarrhea.And 16S sequencing results indicated lactose-free milk powder contributed to increase theα-andβ-diversity of intestinal flora,and restore the intestinal microbiota disorder.In conclusion,our data demonstrate that lactose-free milk powder could alleviate diarrhea by restoring gut microbiota and intestinal barrier function.
基金supported by the Key Research and Development Plan of Shaanxi Province (2023-GHZD-12)the Opening Fund of State Key Laboratory for Strength and Vibration of Mechanical Structures (SVL2021-KF-12)+1 种基金Fundamental Research Funds for the Central Universities (G2020KY05112)the 111 Project (BP0719007)
文摘Nanorubber/epoxy composites containing 0,2,6 and 10 wt%nanorubber are subjected to uniaxial compression over a wide range of strain rate from 8×10^(-4) s^(-1) to~2×10^(4) s^(-1).Unexpectedly,their strain rate sensitivity and strain hardening index increase with increasing nanorubber content.Potential mechanisms are proposed based on numerical simulations using a unit cell model.An increase in the strain rate sensitivity with increasing nanorubber content results from the fact that the nanorubber becomes less incompressible at high strain,generating a higher hydro-static pressure.Adiabatic shear localization starts to occur in the epoxy under a strain rate of 22,000 s^(-1) when the strain exceeds 0.35.The presence of nanorubber in the epoxy reduces adiabatic shear localization by preventing it from propagating.
基金supported by the Hunan Chenyu Fuji New Energy Technology Co. Ltd (2022zkhx501)the Hunan Province University Teaching Reform and Research Project (HNJG-20230364)the Ministry of Education’s Industry-University Cooperation and Collaborative Talent Development Program(231106707093309)。
文摘Zn powder anodes have attracted much attention in aqueous Zn ion battery applications due to advantages such as low cost and processability.However,the high-activity Zn powder anode faces problems such as side reactions,hydrogen evolution,and dendrites,which limit the cycling stability of the cell.In this work,the high activity of Zn powder is weakened by introducing low-cost erythritol as a functional additive in the ZnSO_(4) electrolyte to improve the cycle life of the cell.Both theoretical calculations and empirical evidence demonstrate that the incorporation of erythritol alters the coordination sphere of Zn^(2+)and modifies the local molecular architecture of the electrolyte.This modification serves to diminish the reactivity of water molecules,thereby efficaciously suppressing dendrite formation and deleterious ancillary reactions on the zinc powder anode surfaces.Concurrently,erythritol functions as an interfacial cationic captor,enhancing reaction dynamics and facilitating the development of a favorable protective layer throughout the zinc plating/stripping process.Consequently,the symmetric cell paired with an erythritol-containing electrolyte manifests stable cycling performance for an extended duration of 850 h at a current density of 0.288 mA cm^(-2)and areal capacity of 0.144 mAh cm^(-2).Notably,it maintains a cycling life of 400 h even under intensified conditions (2.88 mA cm^(-2)/1.44 mA h cm^(-2)).Furthermore,the constructed Na_(2)V_(6)O_(16)·3H_(2)O full cell illustrated remarkable capacity retention of 155.8 mA h g^(-1)following 800 cycles at a high rate of 5 A g^(-1).
基金supported by the National Natural Science Foundation of China (Grant No.51991361 and Grant No.51874329)。
文摘The environmental hazards and"carbon footprint"of oil and gas drilling can be significantly reduced by replacing traditional petroleum-based chemical additives with natural materials derived from plants and animals.This paper explored for the first time the interaction mechanism between natural rubber latex(NRL)and bentonite suspensions(BTs)through a series of characterization experiments,as well as the potential applications in water-based drilling fluids(WBDF).The gel viscoelasticity experiments showed that NRL could decrease the consistency coefficient(k)and flow index(n)of BTs,and enhance the shear thinning performance of BTs as pseudo-plastic fluids.In addition,0.5 w/v%NRL not only increased the critical yield stress and strengthened the structural strength between the bentonite particles,but also facilitated the compatibility of pressure loss and flow efficiency.The evaluation of colloidal stability and WBDF performance indicated that NRL particles could promote the hydration and charge stability on the surface of BTs particles,and optimize the particle size distribution and flow resistance of WBDF under the"intercalation-exfoliation-encapsulation"synergistic interaction.Moreover,NRL can improve the rheological properties of WBDF at high temperatures(<150.C),and form a dense blocking layer by bridging and sealing the pores and cracks of the filter cake,which ultimately reduces the permeability of the cake and the filtration loss of WBDF.
基金supported by NIFS budgets,KOBF031,ULFF004,KUHR032partly supported by JSPS KAKENHI 18K04999+2 种基金JSPS-CAS Bilateral Joint Research Projects,“Control of wall recycling on metallic plasma-facing materials in fusion reactor”2019-2022,(No.GJHZ201984)the Chinese Academy of Sciences President’s International Fellowship Initiative Grant No.2024VMB0003 in FY2023the U.S.Department Of Energy under Contract No.DE-AC02-09CH11466 with Princeton University。
文摘In the Large Helical Device(LHD),diborane(B2H6)is used as a standard boron source for boronization,which is assisted by helium glow discharges.In 2019,a new Impurity Powder Dropper(IPD)system was installed and is under evaluation as a real-time wall conditioning technique.In the LHD,which is a large-sized heliotron device,an additional helium(He)glow discharge cleaning(GDC)after boronization was operated for a reduction in hydrogen recycling from the coated boron layers.This operational time of 3 h was determined by spectroscopic data during glow discharges.A flat hydrogen profile is obtained on the top surface of the coated boron on the specimen exposed to boronization.The results suggest a reduction in hydrogen at the top surface by He-GDC.Trapped oxygen in coated boron was obtained by boronization,and the coated boron,which has boron-oxide,on the first wall by B-IPD was also shown.Considering the difference in coating areas between B2H6 boronization and B-IPD operation,it would be most effective to use the IPD and B2H6 boronization coating together for optimized wall conditioning.
基金SASTRA Deemed University,India for its generous research support。
文摘Solid waste recycling is an economically sound strategy for preserving the environment,safeguarding natural resources,and diminishing the reliance on raw material consumption.Geopolymer technology offers a significant advantage by enabling the reuse and recycling of diverse materials.This research assesses how including silica fume and glass powder enhances the impact resistance of ultra-high-performance geopolymer concrete(UHPGC).In total,18 distinct mixtures were formulated by substituting ground granulated blast furnace slag with varying proportions of silica fume and glass powder,ranging from 10%to 40%.Similarly,for each of the mixtures above,steel fibre was added at a dosage of 1.5%to address the inherent brittleness of UHPGC.The mixtures were activated by combining sodium hydroxide and sodium silicate solution to generate geopolymer binders.The specimens were subjected to drop-weight impact testing,wherein an examination was carried out to evaluate various parameters,including flowability,density at fresh and hardened state,compressive strength,impact numbers indicative of cracking and failure occurrences,ductility index,and analysis of failure modes.Additionally,the variations in the impact test outcomes were analyzed using the Weibull distribution,and the findings corresponding to survival probability were offered.Furthermore,the microstructure of UHPGC was scrutinized through scanning electron microscopy.Findings reveal that the specimens incorporating glass powder exhibited lower cracking impact number values than those utilizing silica fume,with reductions ranging from 18.63%to 34.31%.Similarly,failure impact number values decreased from 8.26%to 28.46%across glass powder contents.The maximum compressive and impact strength was recorded in UHPGC,comprising 10%silica fume with fibres.
基金financial support from the French National Research Agency(ANR)[grant number ANR-22-CE06-0031]。
文摘Elastomer blends,among which natural rubber(NR)and butadiene rubber(BR),are involved in many components of the automotive/tire industry.A comprehensive understanding of their mechanical behavior requires,among other features,a detailed description of the crosslink density in these mixtures.In the case of vulcanized immiscible blends,the distribution of the cross-link density within each of the NR-and BR-rich domains is key information,but difficult to determine using the conventional approaches used for one-component crosslinked elastomers.In this study,the vulcanization within NR/BR blends is investigated using a robust^(1)H double-quantum(DQ)MAS recoupling experiment,BaBa-xy16.Two kinds of cross-linked NR/BR blends were considered with two different microstructures for the BR component.The bulk organization of the resulting blends was first probed by analyzing the^(1)H spin-lattice relaxation behavior.In a second step,BaBa-xy16 was used to investigate,in a selective way,the cross-link heterogeneities within NR/BR blends.In particular,for immiscible NR/BR mixtures,the distribution of the cross-link density between both phases was compared and the observed differences were discussed.
基金supported by the National Natural Science Foundation of China,China(Grant Nos.U20B2018,U21B2086,11972087)。
文摘A novel design of micro-aluminum(μAl)powder coated with bi-/tri-component alloy layer,such as:Ni-P and Ni-P-Cu(namely,Al@Ni-P,Al@Ni-P-Cu,respectively),as combustion catalysts,were introduced to release its huge energy inside Al-core and promote rapid pyrolysis of ammonium perchlorate(AP)at a lower temperature in aluminized propellants.The microstructure of Al@Ni-P-Cu demonstrates that a three-layer Ni-P-Cu shell,with the thickness of~100 nm,is uniformly supported byμAl carrier(fuel unit),which has an amorphous surface with a thickness of~2.3 nm(catalytic unit).The peak temperature of AP with the addition of Al@Ni-P-Cu(3.5%)could significantly drop to 316.2℃ at high-temperature thermal decomposition,reduced by 124.3℃,in comparison to that of pure AP with 440.5℃.It illustrated that the introduction of Al@Ni-P-Cu could weaken or even eliminate the obstacle of AP pyrolysis due to its reduction of activation energy with 118.28 kJ/mol.The laser ignition results showed that the ignition delay time of Al@Ni-P-Cu/AP mixture with 78 ms in air is shorter than that of Al@Ni-P/AP(118 ms),decreased by 33.90%.Those astonishing breakthroughs were attributed to the synergistic effects of adequate active sites on amorphous surface and oxidation exothermic reactions(7597.7 J/g)of Al@Ni-P-Cu,resulting in accelerated mass and/or heat transfer rate to catalyze AP pyrolysis and combustion.Moreover,it is believed to provide an alternative Al-based combustion catalyst for propellant designer,to promote the development the propellants toward a higher energy.
