Age is one of the factors which influnce foreign language learning, but not the most important one. Comparision on the effect of foreign language learning between adults and children cannot rely merely on age. So the ...Age is one of the factors which influnce foreign language learning, but not the most important one. Comparision on the effect of foreign language learning between adults and children cannot rely merely on age. So the question of an optimum age for foreign language learning is not a simple one which is only related to age. There are different optimum ages for different aims and demands of learning foreign language.展开更多
Reinforcement of slopes using soil nailing can effectively improve slope stability, and it has been widely used in upgrading cut slopes. Based on the assumptions of stresses on the slip surface, a new method for analy...Reinforcement of slopes using soil nailing can effectively improve slope stability, and it has been widely used in upgrading cut slopes. Based on the assumptions of stresses on the slip surface, a new method for analyzing the stability of a slope reinforced with soil nails was established in the limit equilibrium theory framework, by considering that slope sliding occurs owing to shear failure of the slip surface, which subjects to Mohr–Coulomb(M–C) strength criterion. Meanwhile, in order to easily analyze the stability of a soil nailed slope in actual engineering and facilitate optimum design of parameters for soil nailing, factor of safety(FOS) contour curve charts were drawn on the basis of the established linear proportional relationship between the spacing of soil nails and slope height, and the length of soil nails and slope height. Then, by analyzing and verifying the results obtained from classic examples, some conclusions can be got as follows: 1) The results obtained from the current method are close to those obtained from the traditional limit equilibrium methods, and the current method can provide a strict solution for the slope FOS as it satisfies all the static equilibrium conditions of a sliding body, thus confirming the feasibility of the current method; 2) The slope FOS contour curve charts can be used not only to reliably analyze the stability of a soil nailed slope, but also to design optimally the parameters of soil nailing for the slope with a certain safety requirement.展开更多
In the experiment, the brown rice whose moisture content was 12.5% was used as raw material. The brown rice was grouped, then moisturized differently and milled. While milling, the energy consumption, the rate of brok...In the experiment, the brown rice whose moisture content was 12.5% was used as raw material. The brown rice was grouped, then moisturized differently and milled. While milling, the energy consumption, the rate of broken rice and the crack rate were tested. It is confirmed that the stress crack owing to the moisture added to the brown rice can be avoided when the moisture amount added once is limited to no more than 1.5%. It is also proved that the energy consumption can be reduced, the yielding rate of rice can be increased and that the quality of rice can be improved.展开更多
The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtaine...The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtained. It is found that the stress distribution is very uneven, and the stress convergence is rather severe in the bridge of the aluminum profile extrusion mould. The optimum height of the mould is 70.527 mm, and the optimum radius of dividing holes are 70.182 mm and 80.663 mm. Increasing the height of the mould in the range of 61.282 mm to 70.422 mm can prolong its longevity, but when the height is over 70.422 mm, its longevity reduces.展开更多
To enhance machining efficiency,tool change time has to be reduced.Thus,for an automatic tool changer attached to a machining center,the tool change time is to be reduced.Also the automatic tool changer is a main part...To enhance machining efficiency,tool change time has to be reduced.Thus,for an automatic tool changer attached to a machining center,the tool change time is to be reduced.Also the automatic tool changer is a main part of the machining center as a driving source.The static attributes of the automatic tool changer using the commercial code,ANSYS Workbench V12,were tried to interpret.And the optimum design of automatic tool changer arm was proposed by performing the multi-stage optimum design.The shape optimization of the automatic tool changer was proposed and the result was verified to obtain acceptable improvements.It is possible to obtain an optimized model in which the maximum deformation,maximum stress,and mass are reduced by 10.46%,12.89% and 9.26%,respectively,compared with those of the initial model.Also,the results between conventional method by the design of experiments and proposed method by the multi-stage optimum design method were compared.展开更多
To enhance the quality of grade 20 carbon-steel on the continuous casting production line, the mechanism of forming blowholes and non-metallic inclusions in billets and numerical simulation of flow phenomena about liq...To enhance the quality of grade 20 carbon-steel on the continuous casting production line, the mechanism of forming blowholes and non-metallic inclusions in billets and numerical simulation of flow phenomena about liquid steel in tundish were studied. The results show that the configuration and operation of tundish play an important part in quality assurance of grade 20 carbon-steel products. By optimizing the configuration of the tundish, the depth of liquid bath in tundish is enhanced, the impact of liquid steel is decreased, and the residence time of liquid steel is lengthened, which is useful for eliminating inclusions and blowholes and improving the service life of tundish. Improving the pouring and tapping operation of liquid steel can avoid the contact of liquid steel with air, and decrease re-oxidation. Strict control of the superheat degree of casting liquid steel can decrease the non-metallic inclusion content of the re-oxidation in billets and reduce the erosion of tundish. The inclusions and blowholes in the continuous casting grade 20 steel billets are reduced to a great extent and qualification rate is enhanced from 60% to 80%.展开更多
Complex coupling problems have been existing in electromechanical systems. According to the principles of fractal geometry, an electromechanical system was to be resolved into some simple subsystems that can be easily...Complex coupling problems have been existing in electromechanical systems. According to the principles of fractal geometry, an electromechanical system was to be resolved into some simple subsystems that can be easily described and solved. Pattern recognition theory was applied to recognize the most probable solution space. Multipletarget decision method was used to synthesize the fractal solutions of a system. A kind of fractalconcurrentsynthetic design strategy, and some decoupling optimum techniques were suggested in the article.展开更多
A quality of service （QoS） or constraint-based routing selection needs to find a path subject to multiple constraints through a network. The problem of finding such a path is known as the multi-constrained path （MC...A quality of service （QoS） or constraint-based routing selection needs to find a path subject to multiple constraints through a network. The problem of finding such a path is known as the multi-constrained path （MCP） problem, and has been proven to be NP-complete that cannot be exactly solved in a polynomial time. The NPC problem is converted into a multiobjective optimization problem with constraints to be solved with a genetic algorithm. Based on the Pareto optimum, a constrained routing computation method is proposed to generate a set of nondominated optimal routes with the genetic algorithm mechanism. The convergence and time complexity of the novel algorithm is analyzed. Experimental results show that multiobjective evolution is highly responsive and competent for the Pareto optimum-based route selection. When this method is applied to a MPLS and metropolitan-area network, it will be capable of optimizing the transmission performance.展开更多
The major steps of oilfield development are given in this paper. The optimal model of oilfield development is built and the methods of optimum decision analysis are studied. The solution and analysis of the optimal ta...The major steps of oilfield development are given in this paper. The optimal model of oilfield development is built and the methods of optimum decision analysis are studied. The solution and analysis of the optimal tactics have been set up according to the data collected in the oilfield.展开更多
In this paper, the problem of locally optimum detection of weak pulse signals in narrow-band non-Gaussian noise is discussed. A generalized model is proposed for locally optimum detectors (LOD) and the corresponding p...In this paper, the problem of locally optimum detection of weak pulse signals in narrow-band non-Gaussian noise is discussed. A generalized model is proposed for locally optimum detectors (LOD) and the corresponding physical meaning is explained. On the basis of this generalized model, the LOD structures are derived for detecting both coherent- and incoherent-pulse signals in narrow-band non-Gaussian noise. The asymptotic relative efficiency (ARE) due to Pitman is used to evaluate the performance of these LODs. Finally, numerical calculations are carried out for the AREs of these LODs and some valuable results are obtained.展开更多
A new numerical differentiation method with local opti- mum by data segmentation is proposed. The segmentation of data is based on the second derivatives computed by a Fourier devel- opment method. A filtering process...A new numerical differentiation method with local opti- mum by data segmentation is proposed. The segmentation of data is based on the second derivatives computed by a Fourier devel- opment method. A filtering process is used to achieve acceptable segmentation. Numerical results are presented by using the data segmentation method, compared with the regularization method. For further investigation, the proposed algorithm is applied to the resistance capacitance （RC） networks identification problem, and improvements of the result are obtained by using this algorithm.展开更多
Random error of grinding process is central factor th at give an effect on grinding quality all through. Optimum methods are usually a pplied on grinding process for higher productivity and preferable grinding quali t...Random error of grinding process is central factor th at give an effect on grinding quality all through. Optimum methods are usually a pplied on grinding process for higher productivity and preferable grinding quali ty. But the grinding quality can’t be reliably controlled now and then while opt imal solution of grinding processing parameters have been applied in production, because of two involved aspects which are availability of established empirical formulas and reliability of setting up optimum mathematical model. That is to s ay, there is particular application of optimum methods in grinding process. This paper discussed that how to confirm conditions of grinding test which be po int to grinding peculiarity when test design and regression analysis are used to setting up some empirical formulas. In order to reduce effect of random errors on precision of the empirical formulas and enable them to be applied widely, a m ethod that a lot of random error can be sufficiently contained in grinding test was suggested. And then, A means to ameliorate restriction formulas of grinding quality is expounded based on marked level of the empirical formulas and improve d reliability of optimum mathematical model is given, which offer an effectual w ay for solving grinding quality out of control as a result of random error and w orkable optimal solution of grinding processing parameters can be applied in the production really. Finally, an example is presented.展开更多
An optimum PN guidance law for maneuvering target is developed using optimal control theory.By estimating the target position and setting the cost function,the guidance law can be deduced even without knowing the miss...An optimum PN guidance law for maneuvering target is developed using optimal control theory.By estimating the target position and setting the cost function,the guidance law can be deduced even without knowing the missile lateral acceleration.Since the quadratic cost function can make a compromise between the miss distance and the control constraint,the optimum guidance law obtained is more general.Also,introduced line of sight rate as the input,a practical form of this guidance law is derived.The simulation results show the effectiveness of the guidance laws.展开更多
文摘Age is one of the factors which influnce foreign language learning, but not the most important one. Comparision on the effect of foreign language learning between adults and children cannot rely merely on age. So the question of an optimum age for foreign language learning is not a simple one which is only related to age. There are different optimum ages for different aims and demands of learning foreign language.
基金Project(2015M580702)supported by the Postdoctoral Science Foundation of ChinaProject(51608541)supported by the National Natural Science Foundation of ChinaProject(2014122066)supported by the Guizhou Provincial Department of Transportation Foundation,China
文摘Reinforcement of slopes using soil nailing can effectively improve slope stability, and it has been widely used in upgrading cut slopes. Based on the assumptions of stresses on the slip surface, a new method for analyzing the stability of a slope reinforced with soil nails was established in the limit equilibrium theory framework, by considering that slope sliding occurs owing to shear failure of the slip surface, which subjects to Mohr–Coulomb(M–C) strength criterion. Meanwhile, in order to easily analyze the stability of a soil nailed slope in actual engineering and facilitate optimum design of parameters for soil nailing, factor of safety(FOS) contour curve charts were drawn on the basis of the established linear proportional relationship between the spacing of soil nails and slope height, and the length of soil nails and slope height. Then, by analyzing and verifying the results obtained from classic examples, some conclusions can be got as follows: 1) The results obtained from the current method are close to those obtained from the traditional limit equilibrium methods, and the current method can provide a strict solution for the slope FOS as it satisfies all the static equilibrium conditions of a sliding body, thus confirming the feasibility of the current method; 2) The slope FOS contour curve charts can be used not only to reliably analyze the stability of a soil nailed slope, but also to design optimally the parameters of soil nailing for the slope with a certain safety requirement.
基金Tenth Eive-Year Plan of the Committee of the Scientific Tech. of Heilongjiang Province (GB02B4040-1)Heilongjiang Education Bureau (10511012)
文摘In the experiment, the brown rice whose moisture content was 12.5% was used as raw material. The brown rice was grouped, then moisturized differently and milled. While milling, the energy consumption, the rate of broken rice and the crack rate were tested. It is confirmed that the stress crack owing to the moisture added to the brown rice can be avoided when the moisture amount added once is limited to no more than 1.5%. It is also proved that the energy consumption can be reduced, the yielding rate of rice can be increased and that the quality of rice can be improved.
文摘The finite element analysis and the optimum design of aluminum profile extrusion mould were investigated using the ANSYS software and its parameterized modeling method. The optimum dimensions of the mould were obtained. It is found that the stress distribution is very uneven, and the stress convergence is rather severe in the bridge of the aluminum profile extrusion mould. The optimum height of the mould is 70.527 mm, and the optimum radius of dividing holes are 70.182 mm and 80.663 mm. Increasing the height of the mould in the range of 61.282 mm to 70.422 mm can prolong its longevity, but when the height is over 70.422 mm, its longevity reduces.
基金Work(RTI04-01-03) supported by Grant from Regional Technology Innovation Program of the Ministry of Knowledge Economy (MKE),Korea
文摘To enhance machining efficiency,tool change time has to be reduced.Thus,for an automatic tool changer attached to a machining center,the tool change time is to be reduced.Also the automatic tool changer is a main part of the machining center as a driving source.The static attributes of the automatic tool changer using the commercial code,ANSYS Workbench V12,were tried to interpret.And the optimum design of automatic tool changer arm was proposed by performing the multi-stage optimum design.The shape optimization of the automatic tool changer was proposed and the result was verified to obtain acceptable improvements.It is possible to obtain an optimized model in which the maximum deformation,maximum stress,and mass are reduced by 10.46%,12.89% and 9.26%,respectively,compared with those of the initial model.Also,the results between conventional method by the design of experiments and proposed method by the multi-stage optimum design method were compared.
文摘To enhance the quality of grade 20 carbon-steel on the continuous casting production line, the mechanism of forming blowholes and non-metallic inclusions in billets and numerical simulation of flow phenomena about liquid steel in tundish were studied. The results show that the configuration and operation of tundish play an important part in quality assurance of grade 20 carbon-steel products. By optimizing the configuration of the tundish, the depth of liquid bath in tundish is enhanced, the impact of liquid steel is decreased, and the residence time of liquid steel is lengthened, which is useful for eliminating inclusions and blowholes and improving the service life of tundish. Improving the pouring and tapping operation of liquid steel can avoid the contact of liquid steel with air, and decrease re-oxidation. Strict control of the superheat degree of casting liquid steel can decrease the non-metallic inclusion content of the re-oxidation in billets and reduce the erosion of tundish. The inclusions and blowholes in the continuous casting grade 20 steel billets are reduced to a great extent and qualification rate is enhanced from 60% to 80%.
文摘Complex coupling problems have been existing in electromechanical systems. According to the principles of fractal geometry, an electromechanical system was to be resolved into some simple subsystems that can be easily described and solved. Pattern recognition theory was applied to recognize the most probable solution space. Multipletarget decision method was used to synthesize the fractal solutions of a system. A kind of fractalconcurrentsynthetic design strategy, and some decoupling optimum techniques were suggested in the article.
基金the Natural Science Foundation of Anhui Province of China (050420212)the Excellent Youth Science and Technology Foundation of Anhui Province of China (04042069).
文摘A quality of service （QoS） or constraint-based routing selection needs to find a path subject to multiple constraints through a network. The problem of finding such a path is known as the multi-constrained path （MCP） problem, and has been proven to be NP-complete that cannot be exactly solved in a polynomial time. The NPC problem is converted into a multiobjective optimization problem with constraints to be solved with a genetic algorithm. Based on the Pareto optimum, a constrained routing computation method is proposed to generate a set of nondominated optimal routes with the genetic algorithm mechanism. The convergence and time complexity of the novel algorithm is analyzed. Experimental results show that multiobjective evolution is highly responsive and competent for the Pareto optimum-based route selection. When this method is applied to a MPLS and metropolitan-area network, it will be capable of optimizing the transmission performance.
文摘The major steps of oilfield development are given in this paper. The optimal model of oilfield development is built and the methods of optimum decision analysis are studied. The solution and analysis of the optimal tactics have been set up according to the data collected in the oilfield.
文摘In this paper, the problem of locally optimum detection of weak pulse signals in narrow-band non-Gaussian noise is discussed. A generalized model is proposed for locally optimum detectors (LOD) and the corresponding physical meaning is explained. On the basis of this generalized model, the LOD structures are derived for detecting both coherent- and incoherent-pulse signals in narrow-band non-Gaussian noise. The asymptotic relative efficiency (ARE) due to Pitman is used to evaluate the performance of these LODs. Finally, numerical calculations are carried out for the AREs of these LODs and some valuable results are obtained.
基金supported by the National Basic Research Program of China(2011CB013103)
文摘A new numerical differentiation method with local opti- mum by data segmentation is proposed. The segmentation of data is based on the second derivatives computed by a Fourier devel- opment method. A filtering process is used to achieve acceptable segmentation. Numerical results are presented by using the data segmentation method, compared with the regularization method. For further investigation, the proposed algorithm is applied to the resistance capacitance （RC） networks identification problem, and improvements of the result are obtained by using this algorithm.
文摘Random error of grinding process is central factor th at give an effect on grinding quality all through. Optimum methods are usually a pplied on grinding process for higher productivity and preferable grinding quali ty. But the grinding quality can’t be reliably controlled now and then while opt imal solution of grinding processing parameters have been applied in production, because of two involved aspects which are availability of established empirical formulas and reliability of setting up optimum mathematical model. That is to s ay, there is particular application of optimum methods in grinding process. This paper discussed that how to confirm conditions of grinding test which be po int to grinding peculiarity when test design and regression analysis are used to setting up some empirical formulas. In order to reduce effect of random errors on precision of the empirical formulas and enable them to be applied widely, a m ethod that a lot of random error can be sufficiently contained in grinding test was suggested. And then, A means to ameliorate restriction formulas of grinding quality is expounded based on marked level of the empirical formulas and improve d reliability of optimum mathematical model is given, which offer an effectual w ay for solving grinding quality out of control as a result of random error and w orkable optimal solution of grinding processing parameters can be applied in the production really. Finally, an example is presented.
文摘An optimum PN guidance law for maneuvering target is developed using optimal control theory.By estimating the target position and setting the cost function,the guidance law can be deduced even without knowing the missile lateral acceleration.Since the quadratic cost function can make a compromise between the miss distance and the control constraint,the optimum guidance law obtained is more general.Also,introduced line of sight rate as the input,a practical form of this guidance law is derived.The simulation results show the effectiveness of the guidance laws.
