Compared to the commercial soft-magnetic alloys,the high saturation magnetic flux density(Bs)and low coercivity(Hc)of post-developed novel nanocrystalline alloys tend to realize the miniaturization and lightweight of ...Compared to the commercial soft-magnetic alloys,the high saturation magnetic flux density(Bs)and low coercivity(Hc)of post-developed novel nanocrystalline alloys tend to realize the miniaturization and lightweight of electronic products,thus attracting great attention.In this work,we designed a new FeNiBCuSi formulation with a novel atomic ratio,and the microstructure evolution and magnetic softness were investigated.Microstructure analysis revealed that the amount of Si prompted the differential chemical fluctuations of Cu element,favoring the different nucleation and growth processes ofα-Fe nanocrystals.Furthermore,microstructural defects associated with chemical heterogeneities were unveiled using the Maxwell-Voigt model with two Kelvin units and one Maxwell unit based on creeping analysis by nanoindentation.The defect,with a long relaxation time in relaxation spectra,was more likely to induce the formation of crystal nuclei that ultimately evolved into theα-Fe nanocrystals.As a result,Fe_(84)Ni_(2)B_(12.5)Cu_(1)Si_(0.5)alloy with refined uniform nanocrystalline microstructure exhibited excellent magnetic softness,including a high B_(s)of 1.79 T and very low H_(c)of 2.8 A/m.Our finding offers new insight into the influence of activated defects associated with chemical heterogeneities on the microstructures of nanocrystalline alloy with excellent magnetic softness.展开更多
Temperature effect on atomic deformation of nanotwinned Ni (nt-Ni) under localized nanoindentation is investigated in comparison with nanocrystalline Ni (nc-Ni) through molecular simulation.The nt-Ni exhibits enhanced...Temperature effect on atomic deformation of nanotwinned Ni (nt-Ni) under localized nanoindentation is investigated in comparison with nanocrystalline Ni (nc-Ni) through molecular simulation.The nt-Ni exhibits enhanced critical load and hardness compared to nc-Ni,where perfect,stair-rod and Shockley dislocations are activated at (111),(111) and (111) slip planes in nt-Ni compared to only SSockley dislocation nucleation at (111) and (111) slip planes of nc-Ni.The nt-Ni exhibits a less significant indentation size effect in comparison with nc-Ni due to the dislocation slips hindrance of the twin boundary.The atomic deformation associated with the indentation size effect is investigated during dislocation transmission.Different from the decreasing partial slips parallel to the indenter surface in nc-Ni with increasing temperature,the temperaturedependent atomic deformation of nt-Ni is closely related to the twin boundary:from the partial slips parallel to the twin boundary (~10 K),to increased confined layer slips and decreased twin migration(300 K–600 K),to decreased confined layer slips and increased dislocation interaction of dislocation pinning and dissociation (900 K–1200 K).Dislocation density and atomic structure types through quantitative analysis are implemented to further reveal the above-mentioned dislocation motion and atomic structure alteration.Our study is helpful for understanding the temperature-dependent plasticity of twin boundary in nanotwinned materials.展开更多
In coal mining industry,with the depth growing of coal mines,the creep behaviours of coal and rock can extensively affect the mining safety,coalbed methane recovery and geo-sequestration.To acquire a better insight in...In coal mining industry,with the depth growing of coal mines,the creep behaviours of coal and rock can extensively affect the mining safety,coalbed methane recovery and geo-sequestration.To acquire a better insight into their creep characteristics,an efficient and robust researching technique,nanoindentation,was applied to investigate the creep performances of coal and rock samples obtained from two coal mines in the east of China.Creep characteristics were reflected by evaluating the curves of creep depth versus creep time of nanoindentation tests during the load-holding period at the peak load of 30 mN.These curves can be divided into two stages:transient stage and steady stage;and the time of load-holding period of 5 s,which is the dividing point between two stages,can efficiently avoid the influence of creep displacement on the unloading curves.The exponential function can perfectly fit creep curves and Kelvin model can be used to calculate the rheological parameters of coal and rock samples.Calculated results yield values for the creep modulus and viscosity terms of coal and rock.This study also settled a particular emphasis on the selection of the positions of indentations to obtain the rheological properties of mineralogical constituents in heterogonous coal and rock samples and their elastic aftereffect.展开更多
The creep phenomenon of rocks is quite complex and the creep mechanisms are far from being well understood.Although laboratory creep tests have been carried out to determine the creep deformation of various rocks,thes...The creep phenomenon of rocks is quite complex and the creep mechanisms are far from being well understood.Although laboratory creep tests have been carried out to determine the creep deformation of various rocks,these tests are expensive and time-consuming.Nanoindentation creep tests,as an alternative method,can be performed to investigate the mechanical and viscoelastic properties of granite samples.In this study,the reduced Young’s modulus,hardness,fracture toughness,creep strain rate,stress exponent,activation volume and maximum creep displacement of common rock-forming minerals of granite were calculated from nanoindentation results.It was found that the hardness decreases with the increase of holding time and the initial decrease in hardness was swift,and then it decreased slowly.The stress exponent values obtained were in the range from 4.5 to 22.9,which indicates that dislocation climb is the creep deformation mechanism.In addition,fracture toughness of granite’s rock-forming minerals was calculated using energy-based method and homogenization method was adopted to upscale the micro-scale mechanical properties to macro-scale mechanical properties.Last but not least,both three-element Voigt model and Burgers model fit the nanoindentation creep curves well.This study is beneficial to the understanding of the long-term mechanical properties of rock samples from a microscale perspective,which is of great significance to the understanding of localized deformation processes of rocks.展开更多
The mechanical properties such as Young's modulus, hardness and fracture toughness of Lower Silurian Longmaxi shale samples from Youyang area in southeast Chongqing, China were investigated using dot matrix nanoin...The mechanical properties such as Young's modulus, hardness and fracture toughness of Lower Silurian Longmaxi shale samples from Youyang area in southeast Chongqing, China were investigated using dot matrix nanoindentation measurements. With the help of field emission scanning electron microscope(FESEM) and energy dispersive X-ray fluorescence spectroscopy(EDS), the indentation morphology and mineral composition in indentation area were quantitatively analyzed. According to mechanical strength classification, a micromechanical model with three components was introduced and the Mori-Tanaka model was used to upscale mechanical parameters from nano-scale to centimeter-size scale, which were further compared with uniaxial compression results. The experimental results show that there is a positive linear correlation between Young's modulus and hardness and between the Young's modulus and the fracture toughness under nano-scale; the Young's modulus, hardness and fracture toughness perpendicular to the bedding are slightly lower than those parallel with the bedding. According to data statistics, the mechanical properties at the nano-scale follow Weibull distribution feature and the dispersion degree of hardness results is the highest, which is mainly due to shale anisotropy and nanoindentation projection uncertainty. Comparing the results from nanoindentation test, with those from upscaling model and uniaxial compression test shows that the mechanical parameters at the nano-scale are higher than those from upscaling model and uniaxial compression test, which proves mechanical parameters at different scales have differences. It's because the larger the core, the more pores and internal weakness it contains, the less accurate the interpreted results of mechanical parameters will be.展开更多
In the present work, a three-dimensional molecular dynamics simulation is carried out to perform the nanoindentation experiment on Ni single crystal. The substrate indenter system is modeled using hybrid interatomic p...In the present work, a three-dimensional molecular dynamics simulation is carried out to perform the nanoindentation experiment on Ni single crystal. The substrate indenter system is modeled using hybrid interatomic potentials including the many-body potential embedded atom method （EAM）, and two-body morse potential. To simulate the in- dentation process, a spherical indenter （diameter = 80A, 1A=0.1 nm） is chosen. The results show that the mechanical behaviour of a monolithic Ni is not affected by crystalline orientation. To elucidate the effect of a heterogeneous interface, three bilayer interface systems are constructed, namely Ni（100）/Cu（111）, Ni（110）/Cu（111）, and Ni（111）/Cu（111）. The simulations along these systems clearly describe that mechanical behaviour directly depends on the lattice mismatch. The interface with the smaller mismatch between the specified crystal planes is proved to be harder and vice versa. To describe the relationship between film thickness and interface effect, we choose various values of film thickness ranging from 20 A to 50 A to perform the nanoindentation experiment. It is observed that the interface is significant only for the relatively small thickness of film and the separation between interface and the indenter tip. It is shown that with the increase in film thickness, the mechanical behaviour of the film shifts more toward that of monolithic material.展开更多
A novel Fe-10Cr ferritic/martensitic steel called SIMP was chosen to investigate synergistic effects of H and He on the mechanical properties of structural materials for innovative nuclear energy systems. Sequential a...A novel Fe-10Cr ferritic/martensitic steel called SIMP was chosen to investigate synergistic effects of H and He on the mechanical properties of structural materials for innovative nuclear energy systems. Sequential and separate irradiation experiments on SIMP steel specimens at room temperature using H and He ions with various energy levels were conducted to produce an ion deposition plateau at 300-650 nm. The indentation stress-strain responses were examined using spherical nanoindentation tests after the irradiation experiments. It was found that the sequential irradiation by He and H produced a higher indentation yield stress than separate irradiation, indicating that the hardening was enhanced by the synergy of the H and He irradiation. The micro-mechanism responsible for enhancing the hardening of the SIMP steel through the H and He synergy was investigated using Doppler broadening spectroscopy detection and transmission electron spectroscopy observations.展开更多
Mechanical heterogeneity is a major characteristic of the organic-rich shale.The relation between mechanical heterogeneity and formation in-situ stress has been seldomly addressed but important to understand hydraulic...Mechanical heterogeneity is a major characteristic of the organic-rich shale.The relation between mechanical heterogeneity and formation in-situ stress has been seldomly addressed but important to understand hydraulic fracture propagation,wellbore stability,and hydrocarbon flow.In this paper,the grid nanoindentation technique was used to characterize the heterogeneity of the mechanical properties of Longmaxi organic-rich shales from various burial depths and in-situ stress.The measured elastic modulus and hardness of each sample are deconvolved into three phases including soft phase,medium stiff phase and stiff phase according to mineral category.As the burial depth and corresponding in-situ stress increase,the overall elastic modulus and hardness of the sample enhance.Simultaneously,the percentage of soft minerals decreases,and the probability distribution tends to concentrate through 95%confidence interval evaluation which demonstrates weakened heterogeneity.Furthermore,SEM images provide evidence that extended cracking,initiated cracking,crushing and ductile deforming always occur around indentation imprints.This confirms that even under deep buried depth and high in-situ stress,brittle fracture and ductile deformation can exist synchronously.This paper demonstrates the influence of in-situ stress on the heterogeneity of shale micromechanics.展开更多
Characterizing the mechanical properties of wood cell walls will lead to better understanding and optimization of modifications made to wood infected by the blue-stain fungi.In this study,in situ nanoindentation was u...Characterizing the mechanical properties of wood cell walls will lead to better understanding and optimization of modifications made to wood infected by the blue-stain fungi.In this study,in situ nanoindentation was used to characterize the mechanical properties of the cell walls of Pinus massoniana infected by blue-stain fungi at the cellular level.The results show that in situ nanoindentation is an effective method for this purpose and that blue-stain fungi penetrate wood structures and degrade wood cell walls,significantly reducing the mechanical properties of the cell walls.The method can also be used to evaluate and improve the properties of other wood species infected by blue-stain fungi.展开更多
The dislocation slip behaviors in GaN bulk crystal are investigated by nanoindentation, the dislocation distribution patterns formed around an impress are observed by cathodoluminescence(CL) and cross-sectional transm...The dislocation slip behaviors in GaN bulk crystal are investigated by nanoindentation, the dislocation distribution patterns formed around an impress are observed by cathodoluminescence(CL) and cross-sectional transmission electron microscope(TEM). Dislocation loops, vacancy luminescence, and cross-slips show hexagonal symmetry around the 11-20 and 1-100 direction on c-plane. It is found that the slip planes of dislocation in GaN crystal are dominated in {0001}basal plane and {10-11} pyramid plane. According to the dislocation intersection theory, we come up with the dislocation formation process and the related mechanisms are discussed.展开更多
Molecular dynamics simulations are performed to study the nanoindentation models of monolayer suspended graphene and graphyne. Fullerenes are selected as indenters. Our results show that Young＇s modulus of monolayer-...Molecular dynamics simulations are performed to study the nanoindentation models of monolayer suspended graphene and graphyne. Fullerenes are selected as indenters. Our results show that Young＇s modulus of monolayer-thick graphyne is almost half of that of graphene, which is estimated to be 0.50 TPa. The mechanical properties of graphene and graphyne are different in the presence of strain. A pre-tension has an important effect on the mechanical properties of a membrane. Both the pre-tension and Young＇s modulus plots demonstrate index behavior. The toughness of graphyne is stronger than that of graphene due to Young＇s modulus magnitude. Young＇s moduli of graphene and graphyne are almost independent of the size ratio of indenter to membrane.展开更多
The exploration of Mars would heavily rely on Martian rocks mechanics and engineering technology.As the mechanical property of Martian rocks is uncertain,it is of utmost importance to predict the probability distribut...The exploration of Mars would heavily rely on Martian rocks mechanics and engineering technology.As the mechanical property of Martian rocks is uncertain,it is of utmost importance to predict the probability distribution of Martian rocks mechanical property for the success of Mars exploration.In this paper,a fast and accurate probability distribution method for predicting the macroscale elastic modulus of Martian rocks was proposed by integrating the microscale rock mechanical experiments(micro-RME),accurate grain-based modeling(AGBM)and upscaling methods based on reliability principles.Firstly,the microstructure of NWA12564 Martian sample and elastic modulus of each mineral were obtained by micro-RME with TESCAN integrated mineral analyzer(TIMA)and nanoindentation.The best probability distribution function of the minerals was determined by Kolmogorov-Smirnov(K-S)test.Secondly,based on best distribution function of each mineral,the Monte Carlo simulations(MCS)and upscaling methods were implemented to obtain the probability distribution of upscaled elastic modulus.Thirdly,the correlation between the upscaled elastic modulus and macroscale elastic modulus obtained by AGBM was established.The accurate probability distribution of the macroscale elastic modulus was obtained by this correlation relationship.The proposed method can predict the probability distribution of Martian rocks mechanical property with any size and shape samples.展开更多
The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale an...The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale and Qingshankou continental shale were studied by X-ray diffractometer(XRD),field emission scanning electron microscope(FE-SEM)with mineral analysis system,and nanoindentation.Additionally,the typical bedding layers area was properly stratified using Focused Ion Beam(FIB),and the effects of microstructure and mechanical properties on the distribution patterns of bedding fractures were analyzed.The results show that the Longmaxi marine shale sample contains more clay mineral grains,while the Qingshankou continental shale sample contains more hard brittle mineral grains such as feldspar.For Longmaxi marine shale sample,hard brittle minerals with grain sizes larger than 20μm is18.24%and those with grain sizes smaller than 20μm is 16.22%.For Qingshankou continental shale sample,hard brittle minerals with grain sizes larger than 20μm is 40.7%and those with grain sizes smaller than 20μm is 11.82%.In comparison to the Qingshankou continental shale sample,the Longmaxi marine shale sample has a lower modulus,hardness,and heterogeneity.Laminated shales are formed by alternating coarse-grained and fine-grained layers during deposition.The average single-layer thickness of Longmaxi marine shale sample is greater than Qingshankou continental shale sample.The two types of shale have similar bedding fractures distribution patterns and fractures tend to occur in the transition zone from coarse-grained to fine-grained deposition.The orientation of the fracture is usually parallel to the bedding plane and detour occurs in the presence of hard brittle grains.The fracture distribution density of the Longmaxi marine shale sample is lower than that of the Qingshankou continental shale sample due to the strong heterogeneity of the Qingshankou continental shale.The current research provides guidelines for the effective development of shale reservoirs in various sedimentary environments.展开更多
The degradation of mechanical properties of overdischarge battery materials manifests as a significant effect on the energy density,safety,and cycle life of the batteries.However,establishing the correlation between d...The degradation of mechanical properties of overdischarge battery materials manifests as a significant effect on the energy density,safety,and cycle life of the batteries.However,establishing the correlation between depth of overdischarge and mechanical properties is still a significant challenge.Studying the correlation between depth of overdischarge and mechanical properties is of great significance to improving the energy density and the ability to resist abuse of the batteries.In this paper,the mechanical properties of the battery materials during the whole process of overdischarge from discharge to complete failure were studied.The effects of depth of overdischarge on the elastic modulus and hardness of the cathode of the battery,the tensile strength and the thermal shrinkage rate of the separator,and the performance of binder were investigated.The precipitation of Cu dendrites on the separator and cathode after dissolution of anode copper foil is a key factor affecting the performance of battery materials.The Cu dendrites attached to the cathode penetrate the separator,causing irreversible damage to the coating and base film of the separator,which leads to a sharp decline in the tensile strength,thermal shrinkage rate and other properties of the separator.In addition,the Cu dendrites wrapping the cathode active particles reduce the adhesion of the active particles binder.Meanwhile,the active particles are damaged,resulting in a significant decrease in the elastic modulus and hardness of the cathode.展开更多
The controllable wire bonding of individual Ag nanowires onto a Au electrode was achieved at room temperature. The plastic deformation induced by pressure using nanoindentation could break the protective organic shell...The controllable wire bonding of individual Ag nanowires onto a Au electrode was achieved at room temperature. The plastic deformation induced by pressure using nanoindentation could break the protective organic shell on the surface of the Ag nanowires and cause atomic contact to promote the diffusion and nanojoining at the Ag and Au interface. Severe slip bands were observed in the Ag nanowires after the deformation. A metallic bond was formed at the interface, with the Ag diffusing into the Au more than the Au diffused into the Ag. This nanoscale wire bonding might present opportunities for nanoscale packaging and nanodevice design.展开更多
Residual thermal stress in the system is a serious problem that affects the application of tritium permeation barrier coatings in fusion reactors. The stress not only determines the adhesion between coating and substr...Residual thermal stress in the system is a serious problem that affects the application of tritium permeation barrier coatings in fusion reactors. The stress not only determines the adhesion between coating and substrate, but also changes the properties of the material. In this study,finite element analysis was used to investigate the relationship between the residual thermal stress and the mechanical properties of Al_2O_3 tritium penetration barrier systems. Moreover, the residual thermal stress influenced by factors such as different substrates, temperature, and substrate roughness was also analyzed. The calculation showed that the hardness and elastic modulus increased with increasing compressive stress. However, the hardness and elastic modulus decreased with increasing tensile stress. The systems composed of Al_2O_3 coatings and different substrates exhibited different trends in mechanical properties. As the temperature increased, the hardness and the elastic modulus increased in an Al_2O_3/316 L stainless steel system; the trend was opposite in an Al_2O_3/Si system.Apart from this, the roughness of the substrate surface in the system could magnify the change in hardness and elastic modulus of the coating. Results showed that all these factors led to variation in the mechanical properties of Al_2O_3 tritium permeation barrier systems. Thus, thedetailed reasons for the changes in mechanical properties of these materials need to be analyzed.展开更多
Structural relaxation through isothermal annealing at temperature below glass transition is conducted on Zr46.75 Ti8.25 CU7.5Ni11Be27.5 （Vitreloy-4） bulk metallic glass. Defect concentration is correlated with the a...Structural relaxation through isothermal annealing at temperature below glass transition is conducted on Zr46.75 Ti8.25 CU7.5Ni11Be27.5 （Vitreloy-4） bulk metallic glass. Defect concentration is correlated with the annealing time t according to differential scanning calorimetry thermalgrams. The effects of structural relaxation on mechanical properties and deformation behaviour are investigated by using instrumented nanoindentation. It is found that the as-cast alloy exhibits pronounced serration flow during the loading process of nanoindentation, and the size and number of the serrations decrease with the annealing time. The change of the deformation behaviour with structural relaxation is explained using a free volume model.展开更多
Effects of cold rolling deformation on the microstructure, hardness, and creep behavior of high nitrogen austenitic stainless steel （HNASS） are investigated. Microstructure characterization shows that 70% cold rolli...Effects of cold rolling deformation on the microstructure, hardness, and creep behavior of high nitrogen austenitic stainless steel （HNASS） are investigated. Microstructure characterization shows that 70% cold rolling deformation results in significant refinement of the microstructure of this steel, with its average twin thickness reducing from 6.4 μm to 14 nm. Nanoindentation tests at different strain rates demonstrate that the hardness of the steel with nano-scale twins （nt-HNASS） is about 2 times as high as that of steel with micro-scale twins （mt-HNASS）. The hardness of nt-HNASS exhibits a pronounced strain rate dependence with a strain rate sensitivity （m value） of 0.0319, which is far higher than that of mt-HNASS （m = 0.0029）. nt-HNASS shows more significant load plateaus and a higher creep rate than mt-HNASS. Analysis reveals that higher hardness and larger m value of nt-HNASS arise from stronger strain hardening role, which is caused by the higher storage rate of dislocations and the interactions between dislocations and high density twins. The more significant load plateaus and higher creep rates of nt-HNASS are due to the rapid relaxation of the dislocation structures generated during loading.展开更多
Nanocrystalline Cu with average grain sizes ranging from ～ 24.4 to 131.3 nm were prepared by the electric brushplating technique.Nanoindentation tests were performed within a wide strain rate range,and the creep proc...Nanocrystalline Cu with average grain sizes ranging from ～ 24.4 to 131.3 nm were prepared by the electric brushplating technique.Nanoindentation tests were performed within a wide strain rate range,and the creep process of nanocrystalline Cu during the holding period and its relationship to dislocation and twin structures were examined.It was demonstrated that creep strain and creep strain rate are considerably significant for smaller grain sizes and higher loading strain rates,and are far higher than those predicted by the models of Cobble creep and grain boundary sliding.The analysis based on the calculations and experiments reveals that the significant creep deformation arises from the rapid absorption of high density dislocations stored in the loading regime.Our experiments imply that stored dislocations during loading are highly unstable and dislocation activity can proceed and lead to significant post-loading plasticity.展开更多
Hard coatings have been widely applied to enhance tribological performance of mechanical components.However,it was predicted that thin hard coatings may have a weakening effect which could reduce the coating/substrate...Hard coatings have been widely applied to enhance tribological performance of mechanical components.However,it was predicted that thin hard coatings may have a weakening effect which could reduce the coating/substrate system’s resistance to plastic yielding compared with the uncoated substrate material.In this paper,analytical simulation is utilized to investigate the origin of weakening effect.The functions of material mechanical properties and coating thickness on the weakening effect are theoretically investigated.Partial-unloading spherical nanoindentation tests are performed on tungsten coated single crystalline silicon and copper to acquire the stress-strain curves and compared with the uncoated cases.The experimental results are in consistence with the analytical solutions,demonstrating the presence of weakening effect.展开更多
基金Project supported by the Anhui Provincial Natural Science Foundation(Grant No.2208085QE121)the Key Research&Development Plan of Anhui Province(Grant No.2022a05020016)+1 种基金the University Natural Science Research Project of Anhui Province(Grant No.2023AH051084)the National Natural Science Foundation of China(Grant No.52071078)。
文摘Compared to the commercial soft-magnetic alloys,the high saturation magnetic flux density(Bs)and low coercivity(Hc)of post-developed novel nanocrystalline alloys tend to realize the miniaturization and lightweight of electronic products,thus attracting great attention.In this work,we designed a new FeNiBCuSi formulation with a novel atomic ratio,and the microstructure evolution and magnetic softness were investigated.Microstructure analysis revealed that the amount of Si prompted the differential chemical fluctuations of Cu element,favoring the different nucleation and growth processes ofα-Fe nanocrystals.Furthermore,microstructural defects associated with chemical heterogeneities were unveiled using the Maxwell-Voigt model with two Kelvin units and one Maxwell unit based on creeping analysis by nanoindentation.The defect,with a long relaxation time in relaxation spectra,was more likely to induce the formation of crystal nuclei that ultimately evolved into theα-Fe nanocrystals.As a result,Fe_(84)Ni_(2)B_(12.5)Cu_(1)Si_(0.5)alloy with refined uniform nanocrystalline microstructure exhibited excellent magnetic softness,including a high B_(s)of 1.79 T and very low H_(c)of 2.8 A/m.Our finding offers new insight into the influence of activated defects associated with chemical heterogeneities on the microstructures of nanocrystalline alloy with excellent magnetic softness.
基金supported by the National Natural Science Foundation of China (Grant No.11572090)。
文摘Temperature effect on atomic deformation of nanotwinned Ni (nt-Ni) under localized nanoindentation is investigated in comparison with nanocrystalline Ni (nc-Ni) through molecular simulation.The nt-Ni exhibits enhanced critical load and hardness compared to nc-Ni,where perfect,stair-rod and Shockley dislocations are activated at (111),(111) and (111) slip planes in nt-Ni compared to only SSockley dislocation nucleation at (111) and (111) slip planes of nc-Ni.The nt-Ni exhibits a less significant indentation size effect in comparison with nc-Ni due to the dislocation slips hindrance of the twin boundary.The atomic deformation associated with the indentation size effect is investigated during dislocation transmission.Different from the decreasing partial slips parallel to the indenter surface in nc-Ni with increasing temperature,the temperaturedependent atomic deformation of nt-Ni is closely related to the twin boundary:from the partial slips parallel to the twin boundary (~10 K),to increased confined layer slips and decreased twin migration(300 K–600 K),to decreased confined layer slips and increased dislocation interaction of dislocation pinning and dissociation (900 K–1200 K).Dislocation density and atomic structure types through quantitative analysis are implemented to further reveal the above-mentioned dislocation motion and atomic structure alteration.Our study is helpful for understanding the temperature-dependent plasticity of twin boundary in nanotwinned materials.
基金the projects of the Fundamental Research Funds for the Central Universities(2020ZDPY0221)the Guizhou Science and Technology Department([2020]2Y026)。
文摘In coal mining industry,with the depth growing of coal mines,the creep behaviours of coal and rock can extensively affect the mining safety,coalbed methane recovery and geo-sequestration.To acquire a better insight into their creep characteristics,an efficient and robust researching technique,nanoindentation,was applied to investigate the creep performances of coal and rock samples obtained from two coal mines in the east of China.Creep characteristics were reflected by evaluating the curves of creep depth versus creep time of nanoindentation tests during the load-holding period at the peak load of 30 mN.These curves can be divided into two stages:transient stage and steady stage;and the time of load-holding period of 5 s,which is the dividing point between two stages,can efficiently avoid the influence of creep displacement on the unloading curves.The exponential function can perfectly fit creep curves and Kelvin model can be used to calculate the rheological parameters of coal and rock samples.Calculated results yield values for the creep modulus and viscosity terms of coal and rock.This study also settled a particular emphasis on the selection of the positions of indentations to obtain the rheological properties of mineralogical constituents in heterogonous coal and rock samples and their elastic aftereffect.
基金financial support provided by the China Scholarship Council(No.201706420055)funded by various projects,namely,China Postdoctoral Science Foundation(No.2020M673142)+3 种基金Chongqing Science and Technology Bureau Foundation(No.cstc2020jcyj-bsh0059)Chongqing Human Resources and Social Security Bureau Foundation(No.cx2019100)Chongqing Science and Technology Bureau Foundation(No.cstc2020jcyj-zdxm0122)National Natural Science Foundation of China(No.U19B2009)。
文摘The creep phenomenon of rocks is quite complex and the creep mechanisms are far from being well understood.Although laboratory creep tests have been carried out to determine the creep deformation of various rocks,these tests are expensive and time-consuming.Nanoindentation creep tests,as an alternative method,can be performed to investigate the mechanical and viscoelastic properties of granite samples.In this study,the reduced Young’s modulus,hardness,fracture toughness,creep strain rate,stress exponent,activation volume and maximum creep displacement of common rock-forming minerals of granite were calculated from nanoindentation results.It was found that the hardness decreases with the increase of holding time and the initial decrease in hardness was swift,and then it decreased slowly.The stress exponent values obtained were in the range from 4.5 to 22.9,which indicates that dislocation climb is the creep deformation mechanism.In addition,fracture toughness of granite’s rock-forming minerals was calculated using energy-based method and homogenization method was adopted to upscale the micro-scale mechanical properties to macro-scale mechanical properties.Last but not least,both three-element Voigt model and Burgers model fit the nanoindentation creep curves well.This study is beneficial to the understanding of the long-term mechanical properties of rock samples from a microscale perspective,which is of great significance to the understanding of localized deformation processes of rocks.
基金Supported by the National Natural Science Foundation of China(51704324,41728004,U1762213)China National Science and Technology Major Project(2016ZX05061)
文摘The mechanical properties such as Young's modulus, hardness and fracture toughness of Lower Silurian Longmaxi shale samples from Youyang area in southeast Chongqing, China were investigated using dot matrix nanoindentation measurements. With the help of field emission scanning electron microscope(FESEM) and energy dispersive X-ray fluorescence spectroscopy(EDS), the indentation morphology and mineral composition in indentation area were quantitatively analyzed. According to mechanical strength classification, a micromechanical model with three components was introduced and the Mori-Tanaka model was used to upscale mechanical parameters from nano-scale to centimeter-size scale, which were further compared with uniaxial compression results. The experimental results show that there is a positive linear correlation between Young's modulus and hardness and between the Young's modulus and the fracture toughness under nano-scale; the Young's modulus, hardness and fracture toughness perpendicular to the bedding are slightly lower than those parallel with the bedding. According to data statistics, the mechanical properties at the nano-scale follow Weibull distribution feature and the dispersion degree of hardness results is the highest, which is mainly due to shale anisotropy and nanoindentation projection uncertainty. Comparing the results from nanoindentation test, with those from upscaling model and uniaxial compression test shows that the mechanical parameters at the nano-scale are higher than those from upscaling model and uniaxial compression test, which proves mechanical parameters at different scales have differences. It's because the larger the core, the more pores and internal weakness it contains, the less accurate the interpreted results of mechanical parameters will be.
文摘In the present work, a three-dimensional molecular dynamics simulation is carried out to perform the nanoindentation experiment on Ni single crystal. The substrate indenter system is modeled using hybrid interatomic potentials including the many-body potential embedded atom method （EAM）, and two-body morse potential. To simulate the in- dentation process, a spherical indenter （diameter = 80A, 1A=0.1 nm） is chosen. The results show that the mechanical behaviour of a monolithic Ni is not affected by crystalline orientation. To elucidate the effect of a heterogeneous interface, three bilayer interface systems are constructed, namely Ni（100）/Cu（111）, Ni（110）/Cu（111）, and Ni（111）/Cu（111）. The simulations along these systems clearly describe that mechanical behaviour directly depends on the lattice mismatch. The interface with the smaller mismatch between the specified crystal planes is proved to be harder and vice versa. To describe the relationship between film thickness and interface effect, we choose various values of film thickness ranging from 20 A to 50 A to perform the nanoindentation experiment. It is observed that the interface is significant only for the relatively small thickness of film and the separation between interface and the indenter tip. It is shown that with the increase in film thickness, the mechanical behaviour of the film shifts more toward that of monolithic material.
基金supported by the National Natural Science Foundation of China under grants(Nos.U1832206,11505246,11605256,91426301,11405231,11575258,11375242,and 11505247)the key projects of the Chinese Academy of Sciences(No.ZDRW-CN-2017-1)。
文摘A novel Fe-10Cr ferritic/martensitic steel called SIMP was chosen to investigate synergistic effects of H and He on the mechanical properties of structural materials for innovative nuclear energy systems. Sequential and separate irradiation experiments on SIMP steel specimens at room temperature using H and He ions with various energy levels were conducted to produce an ion deposition plateau at 300-650 nm. The indentation stress-strain responses were examined using spherical nanoindentation tests after the irradiation experiments. It was found that the sequential irradiation by He and H produced a higher indentation yield stress than separate irradiation, indicating that the hardening was enhanced by the synergy of the H and He irradiation. The micro-mechanism responsible for enhancing the hardening of the SIMP steel through the H and He synergy was investigated using Doppler broadening spectroscopy detection and transmission electron spectroscopy observations.
基金financially supported by National Natural Science Foundation of China(No.U19B6003,No.52074315)。
文摘Mechanical heterogeneity is a major characteristic of the organic-rich shale.The relation between mechanical heterogeneity and formation in-situ stress has been seldomly addressed but important to understand hydraulic fracture propagation,wellbore stability,and hydrocarbon flow.In this paper,the grid nanoindentation technique was used to characterize the heterogeneity of the mechanical properties of Longmaxi organic-rich shales from various burial depths and in-situ stress.The measured elastic modulus and hardness of each sample are deconvolved into three phases including soft phase,medium stiff phase and stiff phase according to mineral category.As the burial depth and corresponding in-situ stress increase,the overall elastic modulus and hardness of the sample enhance.Simultaneously,the percentage of soft minerals decreases,and the probability distribution tends to concentrate through 95%confidence interval evaluation which demonstrates weakened heterogeneity.Furthermore,SEM images provide evidence that extended cracking,initiated cracking,crushing and ductile deforming always occur around indentation imprints.This confirms that even under deep buried depth and high in-situ stress,brittle fracture and ductile deformation can exist synchronously.This paper demonstrates the influence of in-situ stress on the heterogeneity of shale micromechanics.
文摘Characterizing the mechanical properties of wood cell walls will lead to better understanding and optimization of modifications made to wood infected by the blue-stain fungi.In this study,in situ nanoindentation was used to characterize the mechanical properties of the cell walls of Pinus massoniana infected by blue-stain fungi at the cellular level.The results show that in situ nanoindentation is an effective method for this purpose and that blue-stain fungi penetrate wood structures and degrade wood cell walls,significantly reducing the mechanical properties of the cell walls.The method can also be used to evaluate and improve the properties of other wood species infected by blue-stain fungi.
文摘The dislocation slip behaviors in GaN bulk crystal are investigated by nanoindentation, the dislocation distribution patterns formed around an impress are observed by cathodoluminescence(CL) and cross-sectional transmission electron microscope(TEM). Dislocation loops, vacancy luminescence, and cross-slips show hexagonal symmetry around the 11-20 and 1-100 direction on c-plane. It is found that the slip planes of dislocation in GaN crystal are dominated in {0001}basal plane and {10-11} pyramid plane. According to the dislocation intersection theory, we come up with the dislocation formation process and the related mechanisms are discussed.
基金Supported by the National Natural Science Foundation of China under Grant No 11274262the Natural Science Foundation of Hunan Province under Grand No 14JJ2046the Program for Changjiang Scholars and Innovative Research Team in Universities under Grant No IRT13093
文摘Molecular dynamics simulations are performed to study the nanoindentation models of monolayer suspended graphene and graphyne. Fullerenes are selected as indenters. Our results show that Young＇s modulus of monolayer-thick graphyne is almost half of that of graphene, which is estimated to be 0.50 TPa. The mechanical properties of graphene and graphyne are different in the presence of strain. A pre-tension has an important effect on the mechanical properties of a membrane. Both the pre-tension and Young＇s modulus plots demonstrate index behavior. The toughness of graphyne is stronger than that of graphene due to Young＇s modulus magnitude. Young＇s moduli of graphene and graphyne are almost independent of the size ratio of indenter to membrane.
文摘The exploration of Mars would heavily rely on Martian rocks mechanics and engineering technology.As the mechanical property of Martian rocks is uncertain,it is of utmost importance to predict the probability distribution of Martian rocks mechanical property for the success of Mars exploration.In this paper,a fast and accurate probability distribution method for predicting the macroscale elastic modulus of Martian rocks was proposed by integrating the microscale rock mechanical experiments(micro-RME),accurate grain-based modeling(AGBM)and upscaling methods based on reliability principles.Firstly,the microstructure of NWA12564 Martian sample and elastic modulus of each mineral were obtained by micro-RME with TESCAN integrated mineral analyzer(TIMA)and nanoindentation.The best probability distribution function of the minerals was determined by Kolmogorov-Smirnov(K-S)test.Secondly,based on best distribution function of each mineral,the Monte Carlo simulations(MCS)and upscaling methods were implemented to obtain the probability distribution of upscaled elastic modulus.Thirdly,the correlation between the upscaled elastic modulus and macroscale elastic modulus obtained by AGBM was established.The accurate probability distribution of the macroscale elastic modulus was obtained by this correlation relationship.The proposed method can predict the probability distribution of Martian rocks mechanical property with any size and shape samples.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52074315&U19B6003)。
文摘The difference in microstructure leads to the diversity of shale mechanical properties and bedding fractures distribution patterns.In this paper,the microstructure and mechanical properties of Longmaxi marine shale and Qingshankou continental shale were studied by X-ray diffractometer(XRD),field emission scanning electron microscope(FE-SEM)with mineral analysis system,and nanoindentation.Additionally,the typical bedding layers area was properly stratified using Focused Ion Beam(FIB),and the effects of microstructure and mechanical properties on the distribution patterns of bedding fractures were analyzed.The results show that the Longmaxi marine shale sample contains more clay mineral grains,while the Qingshankou continental shale sample contains more hard brittle mineral grains such as feldspar.For Longmaxi marine shale sample,hard brittle minerals with grain sizes larger than 20μm is18.24%and those with grain sizes smaller than 20μm is 16.22%.For Qingshankou continental shale sample,hard brittle minerals with grain sizes larger than 20μm is 40.7%and those with grain sizes smaller than 20μm is 11.82%.In comparison to the Qingshankou continental shale sample,the Longmaxi marine shale sample has a lower modulus,hardness,and heterogeneity.Laminated shales are formed by alternating coarse-grained and fine-grained layers during deposition.The average single-layer thickness of Longmaxi marine shale sample is greater than Qingshankou continental shale sample.The two types of shale have similar bedding fractures distribution patterns and fractures tend to occur in the transition zone from coarse-grained to fine-grained deposition.The orientation of the fracture is usually parallel to the bedding plane and detour occurs in the presence of hard brittle grains.The fracture distribution density of the Longmaxi marine shale sample is lower than that of the Qingshankou continental shale sample due to the strong heterogeneity of the Qingshankou continental shale.The current research provides guidelines for the effective development of shale reservoirs in various sedimentary environments.
基金supported by the National Natural Science Foundation of China(92266206,52227810)the Jilin Province Science and Technology Development Plan(YDZJ202101ZYTS129)the Fundamental Research Funds for the Central Universities(2022-JCXK-11)。
文摘The degradation of mechanical properties of overdischarge battery materials manifests as a significant effect on the energy density,safety,and cycle life of the batteries.However,establishing the correlation between depth of overdischarge and mechanical properties is still a significant challenge.Studying the correlation between depth of overdischarge and mechanical properties is of great significance to improving the energy density and the ability to resist abuse of the batteries.In this paper,the mechanical properties of the battery materials during the whole process of overdischarge from discharge to complete failure were studied.The effects of depth of overdischarge on the elastic modulus and hardness of the cathode of the battery,the tensile strength and the thermal shrinkage rate of the separator,and the performance of binder were investigated.The precipitation of Cu dendrites on the separator and cathode after dissolution of anode copper foil is a key factor affecting the performance of battery materials.The Cu dendrites attached to the cathode penetrate the separator,causing irreversible damage to the coating and base film of the separator,which leads to a sharp decline in the tensile strength,thermal shrinkage rate and other properties of the separator.In addition,the Cu dendrites wrapping the cathode active particles reduce the adhesion of the active particles binder.Meanwhile,the active particles are damaged,resulting in a significant decrease in the elastic modulus and hardness of the cathode.
基金supported by the National Natural Science Foundation of China(Grant Numbers 51375261,51520105007,51405258,51605019)support from the Beihang University,China,through Zhuoyue program
文摘The controllable wire bonding of individual Ag nanowires onto a Au electrode was achieved at room temperature. The plastic deformation induced by pressure using nanoindentation could break the protective organic shell on the surface of the Ag nanowires and cause atomic contact to promote the diffusion and nanojoining at the Ag and Au interface. Severe slip bands were observed in the Ag nanowires after the deformation. A metallic bond was formed at the interface, with the Ag diffusing into the Au more than the Au diffused into the Ag. This nanoscale wire bonding might present opportunities for nanoscale packaging and nanodevice design.
文摘Residual thermal stress in the system is a serious problem that affects the application of tritium permeation barrier coatings in fusion reactors. The stress not only determines the adhesion between coating and substrate, but also changes the properties of the material. In this study,finite element analysis was used to investigate the relationship between the residual thermal stress and the mechanical properties of Al_2O_3 tritium penetration barrier systems. Moreover, the residual thermal stress influenced by factors such as different substrates, temperature, and substrate roughness was also analyzed. The calculation showed that the hardness and elastic modulus increased with increasing compressive stress. However, the hardness and elastic modulus decreased with increasing tensile stress. The systems composed of Al_2O_3 coatings and different substrates exhibited different trends in mechanical properties. As the temperature increased, the hardness and the elastic modulus increased in an Al_2O_3/316 L stainless steel system; the trend was opposite in an Al_2O_3/Si system.Apart from this, the roughness of the substrate surface in the system could magnify the change in hardness and elastic modulus of the coating. Results showed that all these factors led to variation in the mechanical properties of Al_2O_3 tritium permeation barrier systems. Thus, thedetailed reasons for the changes in mechanical properties of these materials need to be analyzed.
基金Support by the National Natural Science Foundation of China under Grant Nos 50571109, 10572142 and 10432050, the Knowledge Innovation Project of Chinese Academy of Sciences, and the Natural Science Fund for 0utstanding Youth in Hunan Province under Grant No 02JJYB010.
文摘Structural relaxation through isothermal annealing at temperature below glass transition is conducted on Zr46.75 Ti8.25 CU7.5Ni11Be27.5 （Vitreloy-4） bulk metallic glass. Defect concentration is correlated with the annealing time t according to differential scanning calorimetry thermalgrams. The effects of structural relaxation on mechanical properties and deformation behaviour are investigated by using instrumented nanoindentation. It is found that the as-cast alloy exhibits pronounced serration flow during the loading process of nanoindentation, and the size and number of the serrations decrease with the annealing time. The change of the deformation behaviour with structural relaxation is explained using a free volume model.
基金Project supported by the National Natural Science Foundations of China (Grant Nos.51371089 and 51201068)the National Key Basic Research and Development Program of China (Grant No.2010CB631001)
文摘Effects of cold rolling deformation on the microstructure, hardness, and creep behavior of high nitrogen austenitic stainless steel （HNASS） are investigated. Microstructure characterization shows that 70% cold rolling deformation results in significant refinement of the microstructure of this steel, with its average twin thickness reducing from 6.4 μm to 14 nm. Nanoindentation tests at different strain rates demonstrate that the hardness of the steel with nano-scale twins （nt-HNASS） is about 2 times as high as that of steel with micro-scale twins （mt-HNASS）. The hardness of nt-HNASS exhibits a pronounced strain rate dependence with a strain rate sensitivity （m value） of 0.0319, which is far higher than that of mt-HNASS （m = 0.0029）. nt-HNASS shows more significant load plateaus and a higher creep rate than mt-HNASS. Analysis reveals that higher hardness and larger m value of nt-HNASS arise from stronger strain hardening role, which is caused by the higher storage rate of dislocations and the interactions between dislocations and high density twins. The more significant load plateaus and higher creep rates of nt-HNASS are due to the rapid relaxation of the dislocation structures generated during loading.
基金Project supported by the National Natural Science Foundation of China (Grant Nos. 50771049 and 50871046)the National Basic Research Program of China (Grant No. 2010CB631001)
文摘Nanocrystalline Cu with average grain sizes ranging from ～ 24.4 to 131.3 nm were prepared by the electric brushplating technique.Nanoindentation tests were performed within a wide strain rate range,and the creep process of nanocrystalline Cu during the holding period and its relationship to dislocation and twin structures were examined.It was demonstrated that creep strain and creep strain rate are considerably significant for smaller grain sizes and higher loading strain rates,and are far higher than those predicted by the models of Cobble creep and grain boundary sliding.The analysis based on the calculations and experiments reveals that the significant creep deformation arises from the rapid absorption of high density dislocations stored in the loading regime.Our experiments imply that stored dislocations during loading are highly unstable and dislocation activity can proceed and lead to significant post-loading plasticity.
基金Project supported by the National Natural Science Foundation of China(Grant No.51705533)the National Science and Technology Major Project of China(Grant No.2017-VII-0013-0110)+1 种基金the Fundamental Research Funds for the Central Universities,China(Grant No.2020YQJD17)the Tribology Science Fund of State Key Laboratory of Tribology(Grant No.SKLTKF18B15).
文摘Hard coatings have been widely applied to enhance tribological performance of mechanical components.However,it was predicted that thin hard coatings may have a weakening effect which could reduce the coating/substrate system’s resistance to plastic yielding compared with the uncoated substrate material.In this paper,analytical simulation is utilized to investigate the origin of weakening effect.The functions of material mechanical properties and coating thickness on the weakening effect are theoretically investigated.Partial-unloading spherical nanoindentation tests are performed on tungsten coated single crystalline silicon and copper to acquire the stress-strain curves and compared with the uncoated cases.The experimental results are in consistence with the analytical solutions,demonstrating the presence of weakening effect.
