CO_(2) huff-n-puff shows great potential to promote shale oil recovery after primary depletion.However,the extracting process of shale oil residing in different types of pores induced by the injected CO_(2) remains un...CO_(2) huff-n-puff shows great potential to promote shale oil recovery after primary depletion.However,the extracting process of shale oil residing in different types of pores induced by the injected CO_(2) remains unclear.Moreover,how to saturate shale core samples with oil is still an experimental challenge,and needs a recommended procedure.These issues significantly impede probing CO_(2) huff-n-puff in extracting shale oil as a means of enhanced oil recovery(EOR)processes.In this paper,the oil saturation process of shale core samples and their CO_(2) extraction response with respect to pore types were investigated using online T1-T2nuclear magnetic resonance(NMR)spectroscopy.The results indicated that the oil saturation of shale core samples rapidly increased in the first 16 days under the conditions of 60℃and 30 MPa and then tended to plateau.The maximum oil saturation could reach 46.2%after a vacuum and pressurization duration of 20 days.After saturation,three distinct regions were identified on the T1-T2NMR spectra of the shale core samples,corresponding to kerogen,organic pores(OPs),and inorganic pores(IPs),respectively.The oil trapped in IPs was the primary target for CO_(2) huff-n-puff in shale with a maximum cumulative oil recovery(COR)of 70%original oil in place(OOIP)after three cycles,while the oil trapped in OPs and kerogen presented challenges for extraction(COR<24.2%OOIP in OPs and almost none for kerogen).CO_(2) preferentially extracted the accessible oil trapped in large IPs,while due to the tiny pores and strong affinity of oil-wet walls,the oil saturated in OPs mainly existed in an adsorbed state,leading to an insignificant COR.Furthermore,COR demonstrated a linear increasing tendency with soaking pressure,even when the pressure noticeably exceeded the minimum miscible pressure,implying that the formation of a miscible phase between CO_(2) and oil was not the primary drive for CO_(2) huff-n-puff in shale.展开更多
Based on micro-CT scanning experiments, three-dimensional digital cores of tight sandstones were established to quantitatively evaluate pore-scale anisotropy and pore-distribution heterogeneity. The quartet structure ...Based on micro-CT scanning experiments, three-dimensional digital cores of tight sandstones were established to quantitatively evaluate pore-scale anisotropy and pore-distribution heterogeneity. The quartet structure generation set method was used to generate three-dimensional anisotropic, heterogeneous porous media models. A multi-relaxation-time lattice Boltzmann model was applied to analyze relationships of permeability with pore-scale anisotropy and pore distribution heterogeneity, and the microscopic influence mechanism was also investigated. The tight sandstones are of complex pore morphology, strong anisotropy and pore distribution heterogeneity, while anisotropy factor has obvious directivity. The obvious anisotropy influences the orientation of long axis of pores and fluid flow path, making tortuosity smaller and flowing energy loss less in the direction with the greater anisotropy factor. The strong correlation of tortuosity and anisotropy is the inherent reason of anisotropy acting on permeability. The influence of pore distribution heterogeneity on permeability is the combined effects of specific surface area and tortuosity, while the product of specific surface area and tortuosity shows significantly negative correlation with heterogeneity. The stronger the pore distribution heterogeneity, the smaller the product and the greater the permeability. In addition, the permeability and tortuosity of complex porous media satisfy a power relation with a high fitting precision, which can be applied for approximate estimation of core permeability.展开更多
Seismic inversion performed in the time or frequency domain cannot always recover the long-wavelength background of subsurface parameters due to the lack of low-frequency seismic records. Since the low-frequency respo...Seismic inversion performed in the time or frequency domain cannot always recover the long-wavelength background of subsurface parameters due to the lack of low-frequency seismic records. Since the low-frequency response becomes much richer in the Laplace mixed domains, one novel Bayesian impedance inversion approach in the complex Laplace mixed domains is established in this study to solve the model dependency problem. The derivation of a Laplace mixed-domain formula of the Robinson convolution is the first step in our work. With this formula, the Laplace seismic spectrum, the wavelet spectrum and time-domain reflectivity are joined together. Next, to improve inversion stability, the object inversion function accompanied by the initial constraint of the linear increment model is launched under a Bayesian framework. The likelihood function and prior probability distribution can be combined together by Bayesian formula to calculate the posterior probability distribution of subsurface parameters. By achieving the optimal solution corresponding to maximum posterior probability distribution, the low-frequency background of subsurface parameters can be obtained successfully. Then, with the regularization constraint of estimated low frequency in the Laplace mixed domains, multi-scale Bayesian inversion inthe pure frequency domain is exploited to obtain the absolute model parameters. The effectiveness, anti-noise capability and lateral continuity of Laplace mixed-domain inversion are illustrated by synthetic tests. Furthermore,one field case in the east of China is discussed carefully with different input frequency components and different inversion algorithms. This provides adequate proof to illustrate the reliability improvement in low-frequency estimation and resolution enhancement of subsurface parameters, in comparison with conventional Bayesian inversion in the frequency domain.展开更多
When using a miniature single sensor boundary layer probe, the time sequences of the stream-wise velocity in the turbulent boundary layer （TBL） are measured by using a hot wire anemometer. Beneath the fully develope...When using a miniature single sensor boundary layer probe, the time sequences of the stream-wise velocity in the turbulent boundary layer （TBL） are measured by using a hot wire anemometer. Beneath the fully developed TBL, the wall pressure fluctuations are attained by a microphone mechanism with high spatial resolution. Analysis on the statistic and spectrum properties of velocity and wall pressure reveals the relationship between the wall pressure fluctuation and the energy-containing structure in the buffer layer of the TBL. Wavelet transform shows the multi-scale natures of coherent structures contained in both signals of velocity and pressure. The most intermittent wall pressure scale is associated with the coherent structure in the buffer layer. Meanwhile the most energetic scale of velocity fluctuation at y＋ = 14 provides a specific frequency f9 ≈ 147 Hz for wall actuating control with Ret = 996.展开更多
A multi-scale numerical method coupled with the reactor,sheath and trench model is constructed to simulate dry etching of SiO_2 in inductively coupled C_4F_8 plasmas.Firstly,ion and neutral particle densities in the r...A multi-scale numerical method coupled with the reactor,sheath and trench model is constructed to simulate dry etching of SiO_2 in inductively coupled C_4F_8 plasmas.Firstly,ion and neutral particle densities in the reactor are decided using the CFD-ACE＋ commercial software.Then,the ion energy and angular distributions（IEDs and IADs） are obtained in the sheath model with the sheath boundary conditions provided with CFD-ACE＋.Finally,the trench profile evolution is simulated in the trench model.What we principally focus on is the effects of the discharge parameters on the etching results.It is found that the discharge parameters,including discharge pressure,radio-frequency（rf） power,gas mixture ratios,bias voltage and frequency,have synergistic effects on IEDs and IADs on the etched material surface,thus further affecting the trench profiles evolution.展开更多
This paper proposes a multi-scale self-recovery(MSSR)approach to protect images against content forgery.The main idea is to provide more resistance against image tampering while enabling the recovery process in a mult...This paper proposes a multi-scale self-recovery(MSSR)approach to protect images against content forgery.The main idea is to provide more resistance against image tampering while enabling the recovery process in a multi-scale quality manner.In the proposed approach,the reference data composed of several parts and each part is protected by a channel coding rate according to its importance.The first part,which is used to reconstruct a rough approximation of the original image,is highly protected in order to resist against higher tampering rates.Other parts are protected with lower rates according to their importance leading to lower tolerable tampering rate(TTR),but the higher quality of the recovered images.The proposed MSSR approach is an efficient solution for the main disadvantage of the current methods,which either recover a tampered image in low tampering rates or fails when tampering rate is above the TTR value.The simulation results on 10000 test images represent the efficiency of the multi-scale self-recovery feature of the proposed approach in comparison with the existing methods.展开更多
The high-frequency components in the traditional multi-scale transform method are approximately sparse, which can represent different information of the details. But in the low-frequency component, the coefficients ar...The high-frequency components in the traditional multi-scale transform method are approximately sparse, which can represent different information of the details. But in the low-frequency component, the coefficients around the zero value are very few, so we cannot sparsely represent low-frequency image information. The low-frequency component contains the main energy of the image and depicts the profile of the image. Direct fusion of the low-frequency component will not be conducive to obtain highly accurate fusion result. Therefore, this paper presents an infrared and visible image fusion method combining the multi-scale and top-hat transforms. On one hand, the new top-hat-transform can effectively extract the salient features of the low-frequency component. On the other hand, the multi-scale transform can extract highfrequency detailed information in multiple scales and from diverse directions. The combination of the two methods is conducive to the acquisition of more characteristics and more accurate fusion results. Among them, for the low-frequency component, a new type of top-hat transform is used to extract low-frequency features, and then different fusion rules are applied to fuse the low-frequency features and low-frequency background; for high-frequency components, the product of characteristics method is used to integrate the detailed information in high-frequency. Experimental results show that the proposed algorithm can obtain more detailed information and clearer infrared target fusion results than the traditional multiscale transform methods. Compared with the state-of-the-art fusion methods based on sparse representation, the proposed algorithm is simple and efficacious, and the time consumption is significantly reduced.展开更多
The numerical modeling of oil displacement by nanofluid based on three-dimensional micromodel of cores with different permeability was carried out by the volume of fluid(VOF)method with experimentally measured values ...The numerical modeling of oil displacement by nanofluid based on three-dimensional micromodel of cores with different permeability was carried out by the volume of fluid(VOF)method with experimentally measured values of interfacial tension,contact angle and viscosity.Water-based suspensions of SiO_(2) nanoparticles with a concentration of 0–1%and different particle sizes were considered to study the effect of concentration and size of nanoparticles,displacement fluid flow rate,oil viscosity and core permeability on the efficiency of oil displacement by nanofluid.The oil recovery factor(ORF)increases with the increase of mass fraction of nanoparticles.An increase in nanoparticles’concentration to 0.5% allows an increase in ORF by about 19% compared to water flooding.The ORF increases with the decrease of nanoparticle size,and declines with the increase of displacing rate.It has been shown that the use of nanosuspensions for enhanced oil recovery is most effective for low-permeable reservoirs with highly viscous oil in injection modes with capillary number close to the immobilization threshold,and the magnitude of oil recovery enhancement decreases with the increase of displacement speed.The higher the oil viscosity,the lower the reservoir rock permeability,the higher the ORF improved by nanofluids will be.展开更多
Nb3Sn and other A15 members have been widely applied in nuclear power, nuclear magnetic resonance, and high-energy particle accelerators for their high critical current density （Jc） and upper critical field （Bc2）....Nb3Sn and other A15 members have been widely applied in nuclear power, nuclear magnetic resonance, and high-energy particle accelerators for their high critical current density （Jc） and upper critical field （Bc2）. There have been comprehensive and intensive studies on the applications, the fundamental lattice dynamic and electronic properties, etc., of A15 superconductors. Various reviews on the preparations, structures, and properties have already been written in the last few years. Nevertheless, on account of the large amount of existing facts and views, a coherent view on the relations between the structures and properties has not appeared to unify the facts. This article sketches a multi-scale point of view on the relations between the multi- scale structures and the corresponding properties.展开更多
This paper studies consensus problems in weighted scale-free networks of asymmetrically coupled dynamical units, where the asymmetry in a given link is deter：mined by the relative degree of the involved nodes. It sho...This paper studies consensus problems in weighted scale-free networks of asymmetrically coupled dynamical units, where the asymmetry in a given link is deter：mined by the relative degree of the involved nodes. It shows that the asymmetry of interactions has a great effect on the consensus. Especially, when the interactions are dominant from higher- to lower-degree nodes, both the convergence speed and the robustness to communication delay are enhanced.展开更多
Many real communication networks, such as oceanic monitoring network and land environment observation network,can be described as space stereo multi-layer structure, and the traffic in these networks is concurrent. Un...Many real communication networks, such as oceanic monitoring network and land environment observation network,can be described as space stereo multi-layer structure, and the traffic in these networks is concurrent. Understanding how traffic dynamics depend on these real communication networks and finding an effective routing strategy that can fit the circumstance of traffic concurrency and enhance the network performance are necessary. In this light, we propose a traffic model for space stereo multi-layer complex network and introduce two kinds of global forward-predicting dynamic routing strategies, global forward-predicting hybrid minimum queue（HMQ） routing strategy and global forward-predicting hybrid minimum degree and queue（HMDQ） routing strategy, for traffic concurrency space stereo multi-layer scale-free networks. By applying forward-predicting strategy, the proposed routing strategies achieve better performances in traffic concurrency space stereo multi-layer scale-free networks. Compared with the efficient routing strategy and global dynamic routing strategy, HMDQ and HMQ routing strategies can optimize the traffic distribution, alleviate the number of congested packets effectively and reach much higher network capacity.展开更多
We extend the complexity entropy causality plane（CECP） to propose a multi-scale complexity entropy causality plane（MS-CECP） and further use the proposed method to discriminate the deterministic characteristics of ...We extend the complexity entropy causality plane（CECP） to propose a multi-scale complexity entropy causality plane（MS-CECP） and further use the proposed method to discriminate the deterministic characteristics of different oil-in-water flows. We first take several typical time series for example to investigate the characteristic of the MS-CECP and find that the MS-CECP not only describes the continuous loss of dynamical structure with the increase of scale, but also reflects the determinacy of the system. Then we calculate the MS-CECP for the conductance fluctuating signals measured from oil–water two-phase flow loop test facility. The results indicate that the MS-CECP could be an intrinsic measure for indicating oil-in-water two-phase flow structures.展开更多
Seismic energy decays while propagating subsurface, which may reduce the resolution of seismic data. This paper studies the method of seismic energy dispersion compensation which provides the basic principles for mult...Seismic energy decays while propagating subsurface, which may reduce the resolution of seismic data. This paper studies the method of seismic energy dispersion compensation which provides the basic principles for multi-scale morphology and the spectrum simulation method. These methods are applied in seismic energy compensation. First of all, the seismic data is decomposed into multiple scales and the effective frequency bandwidth is selectively broadened for some scales by using a spectrum simulation method. In this process, according to the amplitude spectrum of each scale, the best simulation range is selected to simulate the middle and low frequency components to ensure the authenticity of the simulation curve which is calculated by the median method, and the high frequency component is broadened. Finally, these scales are reconstructed with reasonable coefficients, and the compensated seismic data can be obtained. Examples are shown to illustrate the feasibility of the energy compensation method.展开更多
A straightforward multi-scale boundary element method is proposed for global and local mechanical analysis of heterogeneous material.The method is more accurate and convenient than finite element based multi-scale met...A straightforward multi-scale boundary element method is proposed for global and local mechanical analysis of heterogeneous material.The method is more accurate and convenient than finite element based multi-scale method.The formulations of this method are derived by combining the homogenization approach and the fundamental equations of boundary element method.The solution gives the convenient formulations to compute global elastic constants and the local stress field.Finally,two numerical examples of porous material are presented to prove the accuracy and the efficiency of the proposed method.The results show that the method does not require the iteration to obtain the solution of the displacement in micro level.展开更多
As the proportion of renewable energy increases, the interaction between renewable energy devices and the grid continues to enhance. Therefore, the renewable energy dynamic test in a power system has become more and m...As the proportion of renewable energy increases, the interaction between renewable energy devices and the grid continues to enhance. Therefore, the renewable energy dynamic test in a power system has become more and more important. Traditional dynamic simulation systems and digital-analog hybrid simulation systems are difficult to compromise on the economy, flexibility and accuracy. A multi-time scale test system of doubly fed induction generator based on FPGA+ CPU heterogeneous calculation is proposed in this paper. The proposed test system is based on the ADPSS simulation platform. The power circuit part of the test system is setup up using the EMT(electromagnetic transient simulation) simulation, and the control part uses the actual physical devices. In order to realize the close-loop testing for the physical devices, the power circuit must be simulated in real-time. This paper proposes a multi-time scale simulation algorithm, in which the decoupling component divides the power circuit into a large time scale system and a small time scale system in order to reduce computing effort. This paper also proposes the FPGA+CPU heterogeneous computing architecture for implementing this multitime scale simulation. In FPGA, there is a complete small time-scale EMT engine, which support the flexibly circuit modeling with any topology. Finally, the test system is connected to an DFIG controller based on Labview to verify the feasibility of the test system.展开更多
基金the financial support of National Key Research and Development Program of China(2023YFE0120700)National Natural Science Foundation of China(52274041)Distinguished Young Sichuan Science Scholars(2023NSFSC1954)。
文摘CO_(2) huff-n-puff shows great potential to promote shale oil recovery after primary depletion.However,the extracting process of shale oil residing in different types of pores induced by the injected CO_(2) remains unclear.Moreover,how to saturate shale core samples with oil is still an experimental challenge,and needs a recommended procedure.These issues significantly impede probing CO_(2) huff-n-puff in extracting shale oil as a means of enhanced oil recovery(EOR)processes.In this paper,the oil saturation process of shale core samples and their CO_(2) extraction response with respect to pore types were investigated using online T1-T2nuclear magnetic resonance(NMR)spectroscopy.The results indicated that the oil saturation of shale core samples rapidly increased in the first 16 days under the conditions of 60℃and 30 MPa and then tended to plateau.The maximum oil saturation could reach 46.2%after a vacuum and pressurization duration of 20 days.After saturation,three distinct regions were identified on the T1-T2NMR spectra of the shale core samples,corresponding to kerogen,organic pores(OPs),and inorganic pores(IPs),respectively.The oil trapped in IPs was the primary target for CO_(2) huff-n-puff in shale with a maximum cumulative oil recovery(COR)of 70%original oil in place(OOIP)after three cycles,while the oil trapped in OPs and kerogen presented challenges for extraction(COR<24.2%OOIP in OPs and almost none for kerogen).CO_(2) preferentially extracted the accessible oil trapped in large IPs,while due to the tiny pores and strong affinity of oil-wet walls,the oil saturated in OPs mainly existed in an adsorbed state,leading to an insignificant COR.Furthermore,COR demonstrated a linear increasing tendency with soaking pressure,even when the pressure noticeably exceeded the minimum miscible pressure,implying that the formation of a miscible phase between CO_(2) and oil was not the primary drive for CO_(2) huff-n-puff in shale.
基金Supported by National Natural Science Foundation of China(U1562217)National Basic Research Program of China(2015CB250900)
文摘Based on micro-CT scanning experiments, three-dimensional digital cores of tight sandstones were established to quantitatively evaluate pore-scale anisotropy and pore-distribution heterogeneity. The quartet structure generation set method was used to generate three-dimensional anisotropic, heterogeneous porous media models. A multi-relaxation-time lattice Boltzmann model was applied to analyze relationships of permeability with pore-scale anisotropy and pore distribution heterogeneity, and the microscopic influence mechanism was also investigated. The tight sandstones are of complex pore morphology, strong anisotropy and pore distribution heterogeneity, while anisotropy factor has obvious directivity. The obvious anisotropy influences the orientation of long axis of pores and fluid flow path, making tortuosity smaller and flowing energy loss less in the direction with the greater anisotropy factor. The strong correlation of tortuosity and anisotropy is the inherent reason of anisotropy acting on permeability. The influence of pore distribution heterogeneity on permeability is the combined effects of specific surface area and tortuosity, while the product of specific surface area and tortuosity shows significantly negative correlation with heterogeneity. The stronger the pore distribution heterogeneity, the smaller the product and the greater the permeability. In addition, the permeability and tortuosity of complex porous media satisfy a power relation with a high fitting precision, which can be applied for approximate estimation of core permeability.
基金the sponsorship of National Natural Science Foundation Project(U1562215,41604101)National Grand Project for Science and Technology(2016ZX05024-004,2017ZX05032-003)+2 种基金the Post-graduate Innovation Program of China University of Petroleum(YCX2017005)Science Foundation from SINOPEC Key Laboratory of Geophysics(wtyjy-wx2016-04-10)the Fundamental Research Funds for the Central Universities
文摘Seismic inversion performed in the time or frequency domain cannot always recover the long-wavelength background of subsurface parameters due to the lack of low-frequency seismic records. Since the low-frequency response becomes much richer in the Laplace mixed domains, one novel Bayesian impedance inversion approach in the complex Laplace mixed domains is established in this study to solve the model dependency problem. The derivation of a Laplace mixed-domain formula of the Robinson convolution is the first step in our work. With this formula, the Laplace seismic spectrum, the wavelet spectrum and time-domain reflectivity are joined together. Next, to improve inversion stability, the object inversion function accompanied by the initial constraint of the linear increment model is launched under a Bayesian framework. The likelihood function and prior probability distribution can be combined together by Bayesian formula to calculate the posterior probability distribution of subsurface parameters. By achieving the optimal solution corresponding to maximum posterior probability distribution, the low-frequency background of subsurface parameters can be obtained successfully. Then, with the regularization constraint of estimated low frequency in the Laplace mixed domains, multi-scale Bayesian inversion inthe pure frequency domain is exploited to obtain the absolute model parameters. The effectiveness, anti-noise capability and lateral continuity of Laplace mixed-domain inversion are illustrated by synthetic tests. Furthermore,one field case in the east of China is discussed carefully with different input frequency components and different inversion algorithms. This provides adequate proof to illustrate the reliability improvement in low-frequency estimation and resolution enhancement of subsurface parameters, in comparison with conventional Bayesian inversion in the frequency domain.
基金Project supported by the National Basic Research Program of China(Grant Nos.2012CB720101 and 2012CB720103)the National Natural Science Foundation of China(Grant Nos.11272233,11332006,and 11411130150)
文摘When using a miniature single sensor boundary layer probe, the time sequences of the stream-wise velocity in the turbulent boundary layer （TBL） are measured by using a hot wire anemometer. Beneath the fully developed TBL, the wall pressure fluctuations are attained by a microphone mechanism with high spatial resolution. Analysis on the statistic and spectrum properties of velocity and wall pressure reveals the relationship between the wall pressure fluctuation and the energy-containing structure in the buffer layer of the TBL. Wavelet transform shows the multi-scale natures of coherent structures contained in both signals of velocity and pressure. The most intermittent wall pressure scale is associated with the coherent structure in the buffer layer. Meanwhile the most energetic scale of velocity fluctuation at y＋ = 14 provides a specific frequency f9 ≈ 147 Hz for wall actuating control with Ret = 996.
基金supported by National Natural Science Foundation of China(No.11375040)the Important National Science&Technology Specific Project of China(No.2011ZX02403-002)
文摘A multi-scale numerical method coupled with the reactor,sheath and trench model is constructed to simulate dry etching of SiO_2 in inductively coupled C_4F_8 plasmas.Firstly,ion and neutral particle densities in the reactor are decided using the CFD-ACE＋ commercial software.Then,the ion energy and angular distributions（IEDs and IADs） are obtained in the sheath model with the sheath boundary conditions provided with CFD-ACE＋.Finally,the trench profile evolution is simulated in the trench model.What we principally focus on is the effects of the discharge parameters on the etching results.It is found that the discharge parameters,including discharge pressure,radio-frequency（rf） power,gas mixture ratios,bias voltage and frequency,have synergistic effects on IEDs and IADs on the etched material surface,thus further affecting the trench profiles evolution.
文摘This paper proposes a multi-scale self-recovery(MSSR)approach to protect images against content forgery.The main idea is to provide more resistance against image tampering while enabling the recovery process in a multi-scale quality manner.In the proposed approach,the reference data composed of several parts and each part is protected by a channel coding rate according to its importance.The first part,which is used to reconstruct a rough approximation of the original image,is highly protected in order to resist against higher tampering rates.Other parts are protected with lower rates according to their importance leading to lower tolerable tampering rate(TTR),but the higher quality of the recovered images.The proposed MSSR approach is an efficient solution for the main disadvantage of the current methods,which either recover a tampered image in low tampering rates or fails when tampering rate is above the TTR value.The simulation results on 10000 test images represent the efficiency of the multi-scale self-recovery feature of the proposed approach in comparison with the existing methods.
基金Project supported by the National Natural Science Foundation of China(Grant No.61402368)Aerospace Support Fund,China(Grant No.2017-HT-XGD)Aerospace Science and Technology Innovation Foundation,China(Grant No.2017 ZD 53047)
文摘The high-frequency components in the traditional multi-scale transform method are approximately sparse, which can represent different information of the details. But in the low-frequency component, the coefficients around the zero value are very few, so we cannot sparsely represent low-frequency image information. The low-frequency component contains the main energy of the image and depicts the profile of the image. Direct fusion of the low-frequency component will not be conducive to obtain highly accurate fusion result. Therefore, this paper presents an infrared and visible image fusion method combining the multi-scale and top-hat transforms. On one hand, the new top-hat-transform can effectively extract the salient features of the low-frequency component. On the other hand, the multi-scale transform can extract highfrequency detailed information in multiple scales and from diverse directions. The combination of the two methods is conducive to the acquisition of more characteristics and more accurate fusion results. Among them, for the low-frequency component, a new type of top-hat transform is used to extract low-frequency features, and then different fusion rules are applied to fuse the low-frequency features and low-frequency background; for high-frequency components, the product of characteristics method is used to integrate the detailed information in high-frequency. Experimental results show that the proposed algorithm can obtain more detailed information and clearer infrared target fusion results than the traditional multiscale transform methods. Compared with the state-of-the-art fusion methods based on sparse representation, the proposed algorithm is simple and efficacious, and the time consumption is significantly reduced.
文摘The numerical modeling of oil displacement by nanofluid based on three-dimensional micromodel of cores with different permeability was carried out by the volume of fluid(VOF)method with experimentally measured values of interfacial tension,contact angle and viscosity.Water-based suspensions of SiO_(2) nanoparticles with a concentration of 0–1%and different particle sizes were considered to study the effect of concentration and size of nanoparticles,displacement fluid flow rate,oil viscosity and core permeability on the efficiency of oil displacement by nanofluid.The oil recovery factor(ORF)increases with the increase of mass fraction of nanoparticles.An increase in nanoparticles’concentration to 0.5% allows an increase in ORF by about 19% compared to water flooding.The ORF increases with the decrease of nanoparticle size,and declines with the increase of displacing rate.It has been shown that the use of nanosuspensions for enhanced oil recovery is most effective for low-permeable reservoirs with highly viscous oil in injection modes with capillary number close to the immobilization threshold,and the magnitude of oil recovery enhancement decreases with the increase of displacement speed.The higher the oil viscosity,the lower the reservoir rock permeability,the higher the ORF improved by nanofluids will be.
基金financially supported by the Science Foundation for International Cooperation of Sichuan Province (2014HH0016)the Fundamental Research Funds for the Central Universities (SWJTU2014: A0920502051113-10000)National Magnetic Confinement Fusion Science Program (2011GB112001)
文摘Nb3Sn and other A15 members have been widely applied in nuclear power, nuclear magnetic resonance, and high-energy particle accelerators for their high critical current density （Jc） and upper critical field （Bc2）. There have been comprehensive and intensive studies on the applications, the fundamental lattice dynamic and electronic properties, etc., of A15 superconductors. Various reviews on the preparations, structures, and properties have already been written in the last few years. Nevertheless, on account of the large amount of existing facts and views, a coherent view on the relations between the structures and properties has not appeared to unify the facts. This article sketches a multi-scale point of view on the relations between the multi- scale structures and the corresponding properties.
基金Project supported by the National Natural Science Foundation of China (Grant Nos 10775060 and 10805033)the Doctoral Education Foundation of National Education Committeethe Natural Science Foundation of Gansu Province
文摘This paper studies consensus problems in weighted scale-free networks of asymmetrically coupled dynamical units, where the asymmetry in a given link is deter：mined by the relative degree of the involved nodes. It shows that the asymmetry of interactions has a great effect on the consensus. Especially, when the interactions are dominant from higher- to lower-degree nodes, both the convergence speed and the robustness to communication delay are enhanced.
基金Project supported by the Youth Science Funds of Shandong Academy of Sciences,China(Grant No.2014QN032)
文摘Many real communication networks, such as oceanic monitoring network and land environment observation network,can be described as space stereo multi-layer structure, and the traffic in these networks is concurrent. Understanding how traffic dynamics depend on these real communication networks and finding an effective routing strategy that can fit the circumstance of traffic concurrency and enhance the network performance are necessary. In this light, we propose a traffic model for space stereo multi-layer complex network and introduce two kinds of global forward-predicting dynamic routing strategies, global forward-predicting hybrid minimum queue（HMQ） routing strategy and global forward-predicting hybrid minimum degree and queue（HMDQ） routing strategy, for traffic concurrency space stereo multi-layer scale-free networks. By applying forward-predicting strategy, the proposed routing strategies achieve better performances in traffic concurrency space stereo multi-layer scale-free networks. Compared with the efficient routing strategy and global dynamic routing strategy, HMDQ and HMQ routing strategies can optimize the traffic distribution, alleviate the number of congested packets effectively and reach much higher network capacity.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.41174109 and 61104148)the National Science and Technology Major Project of China(Grant No.2011ZX05020-006)the Zhejiang Key Discipline of Instrument Science and Technology,China(Grant No.JL130106)
文摘We extend the complexity entropy causality plane（CECP） to propose a multi-scale complexity entropy causality plane（MS-CECP） and further use the proposed method to discriminate the deterministic characteristics of different oil-in-water flows. We first take several typical time series for example to investigate the characteristic of the MS-CECP and find that the MS-CECP not only describes the continuous loss of dynamical structure with the increase of scale, but also reflects the determinacy of the system. Then we calculate the MS-CECP for the conductance fluctuating signals measured from oil–water two-phase flow loop test facility. The results indicate that the MS-CECP could be an intrinsic measure for indicating oil-in-water two-phase flow structures.
文摘Seismic energy decays while propagating subsurface, which may reduce the resolution of seismic data. This paper studies the method of seismic energy dispersion compensation which provides the basic principles for multi-scale morphology and the spectrum simulation method. These methods are applied in seismic energy compensation. First of all, the seismic data is decomposed into multiple scales and the effective frequency bandwidth is selectively broadened for some scales by using a spectrum simulation method. In this process, according to the amplitude spectrum of each scale, the best simulation range is selected to simulate the middle and low frequency components to ensure the authenticity of the simulation curve which is calculated by the median method, and the high frequency component is broadened. Finally, these scales are reconstructed with reasonable coefficients, and the compensated seismic data can be obtained. Examples are shown to illustrate the feasibility of the energy compensation method.
基金Supported by the National Natural Science Foundation of China(51105195,51075204)the Aeronautical Science Foundation of China(2011ZB52024)
文摘A straightforward multi-scale boundary element method is proposed for global and local mechanical analysis of heterogeneous material.The method is more accurate and convenient than finite element based multi-scale method.The formulations of this method are derived by combining the homogenization approach and the fundamental equations of boundary element method.The solution gives the convenient formulations to compute global elastic constants and the local stress field.Finally,two numerical examples of porous material are presented to prove the accuracy and the efficiency of the proposed method.The results show that the method does not require the iteration to obtain the solution of the displacement in micro level.
基金supported by the State Grid Science and Technology Project (Title: Technology Research On Large Scale EMT Real-time simulation customized platform, FX71-17-001)
文摘As the proportion of renewable energy increases, the interaction between renewable energy devices and the grid continues to enhance. Therefore, the renewable energy dynamic test in a power system has become more and more important. Traditional dynamic simulation systems and digital-analog hybrid simulation systems are difficult to compromise on the economy, flexibility and accuracy. A multi-time scale test system of doubly fed induction generator based on FPGA+ CPU heterogeneous calculation is proposed in this paper. The proposed test system is based on the ADPSS simulation platform. The power circuit part of the test system is setup up using the EMT(electromagnetic transient simulation) simulation, and the control part uses the actual physical devices. In order to realize the close-loop testing for the physical devices, the power circuit must be simulated in real-time. This paper proposes a multi-time scale simulation algorithm, in which the decoupling component divides the power circuit into a large time scale system and a small time scale system in order to reduce computing effort. This paper also proposes the FPGA+CPU heterogeneous computing architecture for implementing this multitime scale simulation. In FPGA, there is a complete small time-scale EMT engine, which support the flexibly circuit modeling with any topology. Finally, the test system is connected to an DFIG controller based on Labview to verify the feasibility of the test system.
