The unit cell configuration of lattice structures critically influences their load-bearing and energy absorption performance.In this study,three novel lattice structures were developed by modifying the conventional FB...The unit cell configuration of lattice structures critically influences their load-bearing and energy absorption performance.In this study,three novel lattice structures were developed by modifying the conventional FBCCZ unit cell through reversing,combining,and turning strategies.The designed lattices were fabricated via laser powder bed fusion(LPBF)using Ti-6Al-4V powder,and the mechanical properties,energy absorption capacity,and deformation behaviors were systematically investigated through quasi-static compression tests and finite element simulations.The results demonstrate that the three modified lattices exhibit superior performance over the conventional FBCCZ structure in terms of fracture strain,specific yield strength,specific ultimate strength,specific energy absorption,and energy absorption efficiency,thereby validating the efficacy of unit cell modifications in enhancing lattice performance.Notably,the CFBCCZ and TFBCCZ lattices significantly outperform both the FBCCZ and RFBCCZ lattice structures in load-bearing and energy absorption.While TFBCCZ shows marginally higher specific elastic modulus and energy absorption efficiency than CFBCCZ,the latter achieves superior energy absorption due to its highest ultimate strength and densification strain.Finite element simulations further reveal that the modified lattices,through optimized redistribution and adjustment of internal nodes and struts,effectively alleviate stress concentration during loading.This structural modification enhances the structural integrity and deformation stability under external loads,enabling a synergistic enhancement of load-bearing capacity and energy absorption performance.展开更多
The mechanical properties of many materials prepared by additive manufacturing technology have been greatly improved.High strength is attributed to grain refinement,formation of high density dislocation and existence ...The mechanical properties of many materials prepared by additive manufacturing technology have been greatly improved.High strength is attributed to grain refinement,formation of high density dislocation and existence of cellular structures with nanoscale during manufacturing.In addition,the super-saturated solid solution of elements in the matrix and the solid solution segregation along the wall of the cellular structures also promote the improvement of strength by enhancing dislocation pinning.Hence,the existence of cellular structure in grains leads to differences in the prediction of material strength by Hall-Petch relationship,and there is no unified calculation method to determine the d value as grain size or cell size.In this work,representative materials including austenite 316L SS were printed by selective laser melting(SLM),and the strength was predicted.The values of cell size and grain size were substituted into Hall-Petch formula,and the results showed that the calculation error for 316L is increased from 4.1%to 11.9%.Therefore,it is concluded that the strength predicted by grain size is more accurate than that predicted by cell size in additive manufacturing materials.When calculating the yield strength of laser additive manufacturing metal materials through the Hall-Petch formula,the grain size should be used as the basis for calculation.展开更多
A yttrium-containing high-temperature titanium alloy(Ti-6Al-2.7Sn-4Zr-0.4Mo-0.45Si-0.1Y, mass fraction, %) has been additively manufactured using selective electron beam melting(SEBM). The resulting microstructure and...A yttrium-containing high-temperature titanium alloy(Ti-6Al-2.7Sn-4Zr-0.4Mo-0.45Si-0.1Y, mass fraction, %) has been additively manufactured using selective electron beam melting(SEBM). The resulting microstructure and textures were studied using scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD) and electron backscattered diffraction(EBSD) and compared with the conventionally manufactured form. A notable distinct difference of microstructures is that additive manufacturing by SEBM enables homogeneous precipitation of fine Y2O3 dispersoids in the size range of 50-250 nm throughout the as-fabricated alloy, despite the presence of just trace levels of oxygen(7×10-4, mass fraction) and yttrium(10-3, mass fraction) in the alloy. In contrast, the conventionally manufactured alloy shows inhomogeneously distributed coarse Y2O3 precipitates, including cracked or debonded Y2O3 particles.展开更多
NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emph...NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emphasis on its phase composition,microstructure,mechanical property and deformation mechanism.The results show that the yield strength and ductility obtained by SLM are 100 MPa and 8%,respectively,which are remarkably different from DED result with 700 MPa and 2%.The load path of SLM sample presents shape memory effect,corresponding to martensite phase detected by XRD;while the load path of DED presents pseudo-elasticity with austenite phase.In SLM sample,fine grain and hole provide a uniform deformation during tensile test,resulting in a better elongation.Furthermore,the nonequilibrium solidification was studied by a temperature field simulation to understand the difference of the two 3D printing methods.Both temperature gradient G and growth rate R determine the microstructure and phase in the SLM sample and DED sample,which leads to similar grain morphologies because of similar G/R.While higher G×R of SLM leads to a finer grain size in SLM sample,providing enough driving force for martensite transition and subsequently changing texture compared to DED sample.展开更多
A slotting method for cosine gears was proposed by using the involute cutter based on the conjugate theories of digital surface and gear meshing. The slotting model between the cosine tooth surface represented by disc...A slotting method for cosine gears was proposed by using the involute cutter based on the conjugate theories of digital surface and gear meshing. The slotting model between the cosine tooth surface represented by discrete points and the cutter figuration determined by analytic function was built for their geometrical relationship and conjugate motion during the machining process. Conjugate points in the cutter section corresponding to the discrete points on the cosine gear tooth surface and the conjugate movements were solved. By using the flexible control of the CNC procedure, the active control of the cutting trace of the slotting cutter was accomplished and the envelop forming of the cosine gear was obtained. Based on the software C++ and Matlab, the computer aided manufacturing(CAM) system of the cosine gear was developed, and the simulation of the slotting process was accomplished. Several examples were provided to illustrate the approach. The result of the simulation demonstrates that the proposed slotting method is feasible.展开更多
Production of ceramic armour solutions on-demand/in-theatre would have significant logistical and military advantages.However,even assuming that such technologies could be successfully deployed in the field,such near ...Production of ceramic armour solutions on-demand/in-theatre would have significant logistical and military advantages.However,even assuming that such technologies could be successfully deployed in the field,such near net-shape manufacturing technology is relatively immature compared to conventional sintering of ceramics.In this study,the ballistic performance of a series of additively manufactured(AM)/rapidly-prototyped(RP)alumina tiles of 97.2%of the density of Sintox FATM were investigated using both forward-and reverse-ballistic experiments.These experiments,undertaken with compressed gasguns,employed the depth-of-penetration technique and flash X-ray as primary diagnostics to interrogate both efficiency of penetration and projectile-target interaction,respectively.The RP alumina was found to exhibit useful ballistic properties,successfully defeating steel-cored(AP)7.62×39 mm BXN rounds at velocities of up-to c.a.850 m/s,while exhibiting comparable failure modes to conventionally sintered armour-grade Sintox FATM.However,where a<1%by vol.Cu dopant was introduced into the RP material failure modes changed dramatically with performance dropping below that of conventionally sintered alumina.Overall,the results from both sets of experiments were complimentary and clearly indicated the potential of such RP materials to play an active role in provision of real-world body armour solutions provided quality control of the RP material can be maintained.展开更多
This paper presents the first-ever investigation of Menger fractal cubes'quasi-static compression and impact behaviour.Menger cubes with different void ratios were 3D printed using polylactic acid(PLA)with dimensi...This paper presents the first-ever investigation of Menger fractal cubes'quasi-static compression and impact behaviour.Menger cubes with different void ratios were 3D printed using polylactic acid(PLA)with dimensions of 40 mm×40 mm×40 mm.Three different orders of Menger cubes with different void ratios were considered,namely M1 with a void ratio of 0.26,M2 with a void ratio of 0.45,and M3with a void ratio of 0.60.Quasi-static Compression tests were conducted using a universal testing machine,while the drop hammer was used to observe the behaviour under impact loading.The fracture mechanism,energy efficiency and force-time histories were studied.With the structured nature of the void formation and predictability of the failure modes,the Menger geometry showed some promise compared to other alternatives,such as foams and honeycombs.With the increasing void ratio,the Menger geometries show force-displacement behaviour similar to hyper-elastic materials such as rubber and polymers.The third-order Menger cubes showed the highest energy absorption efficiency compared to the other two geometries in this study.The findings of the present work reveal the possibility of using additively manufactured Menger geometries as an energy-efficient system capable of reducing the transmitting force in applications such as crash barriers.展开更多
Wire-arc additive manufacture(WAAM)has great potential for manufacturing of Al-Cu components.However,inferior mechanical properties of WAAM deposited material restrict its industrial application.Inter-layer cold rolli...Wire-arc additive manufacture(WAAM)has great potential for manufacturing of Al-Cu components.However,inferior mechanical properties of WAAM deposited material restrict its industrial application.Inter-layer cold rolling and thermo-mechanical heat treatment(T8)with pre-stretching deformation between solution and aging treatment were adopted in this study.Their effects on hardness,mechanical properties and microstructure were analyzed and compared to the conventional heat treatment(T6).The results show that cold rolling increases the hardness and strengths,which further increase with T8 treatment.The ultimate tensile strength(UTS)of 513 MPa and yield stress(YS)of 413 MPa can be obtained in the inter-layer cold-rolled sample with T8 treatment,which is much higher than that in the as-deposited samples.The cold-rolled samples show higher elongation than that of as-deposited ones due to significant elimination of porosity in cold rolling;while both the T6 and T8 treatments decrease the elongation.The cold rolling and pre-stretching deformation both contribute to the formation of dense and dispersive precipitatedθ′phases,which inhibits the dislocation movement and enhances the strengths;as a result,T8 treatment shows better strengthening effect than the T6 treatment.The strengthening mechanism was analyzed and it was mainly related to work hardening and precipitation strengthening.展开更多
Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects s...Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects such as porosity issues, significant deformation, surface cracks, and challenging control of surface morphology encountered during the selective laser melting(SLM) additive manufacturing(AM) process of specialized Micro Electromechanical System(MEMS) components, multiparameter optimization and micro powder melt pool/macro-scale mechanical properties control simulation of specialized components are conducted. The optimal parameters obtained through highprecision preparation and machining of components and static/high dynamic verification are: laser power of 110 W, laser speed of 600 mm/s, laser diameter of 75 μm, and scanning spacing of 50 μm. The density of the subordinate components under this reference can reach 99.15%, the surface hardness can reach 51.9 HRA, the yield strength can reach 550 MPa, the maximum machining error of the components is 4.73%, and the average surface roughness is 0.45 μm. Through dynamic hammering and high dynamic firing verification, SLM components meet the requirements for overload resistance. The results have proven that MEM technology can provide a new means for the processing of MEMS components applied in high dynamic environments. The parameters obtained in the conclusion can provide a design basis for the additive preparation of MEMS components.展开更多
According to different damage modes,warheads are roughly divided into three types:fragmentation warheads,shaped charge warheads,and penetrating warheads.Due to limitations in material and structural manufacturing,trad...According to different damage modes,warheads are roughly divided into three types:fragmentation warheads,shaped charge warheads,and penetrating warheads.Due to limitations in material and structural manufacturing,traditional manufacturing methods make it difficult to fully utilize the damage ability of the warhead.Additive manufacturing(AM)technology can fabricate complex structures,with classified materials composition and customized components,while achieving low cost,high accuracy,and rapid production of the parts.The maturity of AM technology has brought about a new round of revolution in the field of warheads.In this paper,we first review the principles,classifications,and characteristics of different AM technologies.The development trends of AM technologies are pointed out,including multi-material AM technology,hybrid AM technology,and smart AM technology.From our survey,PBF,DED,and EBM technologies are mainly used to manufacture warhead damage elements.FDM and DIW technologies are mainly used to manufacture warhead charges.Then,the research on the application of AM technology in three types of warhead and warhead charges was reviewed and the existing problems and progress of AM technologies in each warhead were analyzed.Finally,we summarized the typical applications and look forward to the application prospects of AM technology in the field of warheads.展开更多
Because of an unfortunate mistake during the production of this article,the Acknowledgements have been omitted.The Acknowledgements are added as follows:Sasan YAZDANI would like to thank the Scientific and Technologic...Because of an unfortunate mistake during the production of this article,the Acknowledgements have been omitted.The Acknowledgements are added as follows:Sasan YAZDANI would like to thank the Scientific and Technological Research Council of Turkey(TÜB˙ITAK)for receiving financial support for this work through the 2221 Fellowship Program for Visiting Scientists and Scientists on Sabbatical Leave(Grant ID:E 21514107-115.02-228864).Sasan YAZDANI also expresses his gratitude to Sahand University of Technology for granting him sabbatical leave to facilitate the completion of this research.展开更多
Military missions in hostile environments are often costly and unpredictable,with squadrons sometimes facing isolation and resource scarcity.In such scenarios,critical components in vehicles,drones,and energy generato...Military missions in hostile environments are often costly and unpredictable,with squadrons sometimes facing isolation and resource scarcity.In such scenarios,critical components in vehicles,drones,and energy generators may require structural reinforcement or repair due to damage.This paper proposes a portable,on-site production method for molds under challenging conditions,where material supply is limited.The method utilizes large format additive manufacturing(LFAM)with recycled composite materials,sourced from end-of-life components and waste,as feedstock.The study investigates the microstructural effects of recycling through shredding techniques,using microscopic imaging.Three potential defense-sector applications are explored,specifically in the aerospace,automotive,and energy industries.Additionally,the influence of key printing parameters,particularly nonparallel plane deposition at a 45-degree angle,on the mechanical behavior of ABS reinforced with 20%glass fiber(GF)is examined.The results demonstrate the feasibility of this manufacturing approach,highlighting reductions in waste material and production times compared to traditional methods.Shorter layer times were found to reduce thermal gradients between layers,thereby improving layer adhesion.While 45-degree deposition enhanced Young's modulus,it slightly reduced interlayer adhesion quality.Furthermore,recycling-induced fiber length reduction led to material degradation,aligning with findings from previous studies.Challenges encountered during implementation included weak part adherence to the print bed and local excess material deposition.Overall,the proposed methodology offers a cost-effective alternative to traditional CNC machining for mold production,demonstrating its potential for on-demand manufacturing in resource-constrained environments.展开更多
The present work explores the feasibility of fabricating porous 3D parts in TiAl intermetallic alloy directly from Tie6Ale4V and Al powders. This approach uses a binder jetting additive manufacturing process followed ...The present work explores the feasibility of fabricating porous 3D parts in TiAl intermetallic alloy directly from Tie6Ale4V and Al powders. This approach uses a binder jetting additive manufacturing process followed by reactive sintering. The results demonstrate that the present approach is successful for realizing parts in TiAl intermetallic alloy.展开更多
Pursuing the green manufacturing (GM) of products i s very beneficial in the alleviation of environment burdens. In order to reap such benefits, green manufacturing is involved in every aspect of manufacturing proc es...Pursuing the green manufacturing (GM) of products i s very beneficial in the alleviation of environment burdens. In order to reap such benefits, green manufacturing is involved in every aspect of manufacturing proc esses. During the machining process, cutting fluid is one of the main roots of e nvironmental pollution. And how to make an optimal selection for cutting fluid f or GM is an important path to reduce the environmental pollution. The objective factors of decision-making problems in the traditional selection of cutting flu id are usually two: quality and cost. But from the viewpoint of GM, environmenta l impact (E) should be considered together. In this paper, a multi-object d ecision-making model of cutting fluid selection for GM is put forward, in which the objects of Quality (Q), Cost(C) and Environmental impact (E) are considered together. In this model, E means to minimize the environmental impact, Q means to maximize the quality and C means to minimize the cost. Each objective is anal yzed in detail too. A case study on a decision-making problem of cutting fluid selection in a gear hobbing process is analyzed, and the result shows the model is practical.展开更多
Achieving sustainable patterns of consumption and production is perhaps the biggest challenge facing our society today. The de-mand for more safe environmentally benign products is rising and many companies are lookin...Achieving sustainable patterns of consumption and production is perhaps the biggest challenge facing our society today. The de-mand for more safe environmentally benign products is rising and many companies are looking for new ways to progressively improve the sus-tainability of their products. Moreover, there are numerous opportunities and countless innovations, technological as well as non-technologi-cal,that need to be exploited to improve the sustainability of products. Manufacturing industry is an important sector of any economy and hasthe potential to become a driving force for enabling sustainable patterns of production and consumption through introducing efficient productionpractices and developing products and services that help reduce environmental impacts. The benefits of adopting an integrated policy towardsproduct development based on life cycle thinking and eco-design to stimulate improvement of the environmental performance of each part ofproduct life cycle phases and achieve sustainable patterns of production and consumption are emphasized. The challenges in implementingsustainable manufacturing and the circular economy approaches are listed. A number of solutions are suggested to face up these challenges,for instance, increased awareness of enterprises particularly SME's of product life cycle issues and the opportunities that are available for costsavings and profit making from eco-innovation in product development for both the domestic and export markets and providing practical helpand advice directly to enterprises on integrated product development to promote enterprise led Eco-innovation. Aiming at contributing to sus-tainable manufacturing in China, Sino-UK Low Carbon Manufacturing Consortium, a multi-disciplinary research and educational partnershipbetween academia, industry and government agencies in the UK and China with interest in sustainable manufacturing issues, has been formedrecently.The vision, aims and benefits of membership of the consortium are also discussed.展开更多
Additive manufacturing is a new emerging technology which is ideal for low-to-zero waste production, and it is considered to be a green and clean process that has the potential to lower the cost and energy consumption...Additive manufacturing is a new emerging technology which is ideal for low-to-zero waste production, and it is considered to be a green and clean process that has the potential to lower the cost and energy consumption of production. However, the cost of the feedstock for additive manufacturing and the additive manufactured parts is usually very high, which hinders the further application of additive manufacturing, especially for the metal additive manufacturing. The concept of circular metal additive manufacturing involves the recycling of the metal feedstock and the additive manufactured parts leading to the truly zero waste production and the most energy saving. This paper reviews the technologies that help the formation of a circular metal additive manufacturing through recycling of the feedstocks and the damaged metal parts. Reactive metals, such as titanium, tend to be contaminated easily during handling and production. Recycling of the titanium for achieving a circular titanium additive manufacturing is reviewed in detail.展开更多
Cloud manufacturing is a specific implementation form of the "Internet + manufacturing" strategy. Why and how to develop cloud manufacturing platform(CMP), however, remains the key concern of both platform o...Cloud manufacturing is a specific implementation form of the "Internet + manufacturing" strategy. Why and how to develop cloud manufacturing platform(CMP), however, remains the key concern of both platform operators and users. A microscopic model is proposed to investigate advantages and diffusion forces of CMP through exploration of its diffusion process and mechanism. Specifically, a three-stage basic evolution process of CMP is innovatively proposed. Then, based on this basic process, a more complex CMP evolution model has been established in virtue of complex network theory, with five diffusion forces identified. Thereafter, simulations on CMP diffusion have been conducted. The results indicate that, CMP possesses better resource utilization,user satisfaction, and enterprise utility. Results of simulation on impacts of different diffusion forces show that both the time required for CMP to reach an equilibrium state and the final network size are affected simultaneously by the five diffusion forces. All these analyses indicate that CMP could create an open online cooperation environment and turns out to be an effective implementation of the "Internet + manufacturing" strategy.展开更多
How to deal with the collaboration between task decomposition and task scheduling is the key problem of the integrated manufacturing system for complex products. With the development of manufacturing technology, we ca...How to deal with the collaboration between task decomposition and task scheduling is the key problem of the integrated manufacturing system for complex products. With the development of manufacturing technology, we can probe a new way to solve this problem. Firstly, a new method for task granularity quantitative analysis is put forward, which can precisely evaluate the task granularity of complex product cooperation workflow in the integrated manufacturing system, on the above basis; this method is used to guide the coarse-grained task decomposition and recombine the subtasks with low cohesion coefficient. Then, a multi-objective optimieation model and an algorithm are set up for the scheduling optimization of task scheduling. Finally, the application feasibility of the model and algorithm is ultimately validated through an application case study.展开更多
基金supported by National Key Lab of Aerospace Power System and Plasma Technology Foundation of China(Grant No.APSPT202301002)National Natural Science Foundation of China(Grant No.52001038)Natural Science Foundation of Chongqing,China(Grant Nos.cstc2019jcyj-msxm X0787 and cstc2021jcyj-msxm X0011)。
文摘The unit cell configuration of lattice structures critically influences their load-bearing and energy absorption performance.In this study,three novel lattice structures were developed by modifying the conventional FBCCZ unit cell through reversing,combining,and turning strategies.The designed lattices were fabricated via laser powder bed fusion(LPBF)using Ti-6Al-4V powder,and the mechanical properties,energy absorption capacity,and deformation behaviors were systematically investigated through quasi-static compression tests and finite element simulations.The results demonstrate that the three modified lattices exhibit superior performance over the conventional FBCCZ structure in terms of fracture strain,specific yield strength,specific ultimate strength,specific energy absorption,and energy absorption efficiency,thereby validating the efficacy of unit cell modifications in enhancing lattice performance.Notably,the CFBCCZ and TFBCCZ lattices significantly outperform both the FBCCZ and RFBCCZ lattice structures in load-bearing and energy absorption.While TFBCCZ shows marginally higher specific elastic modulus and energy absorption efficiency than CFBCCZ,the latter achieves superior energy absorption due to its highest ultimate strength and densification strain.Finite element simulations further reveal that the modified lattices,through optimized redistribution and adjustment of internal nodes and struts,effectively alleviate stress concentration during loading.This structural modification enhances the structural integrity and deformation stability under external loads,enabling a synergistic enhancement of load-bearing capacity and energy absorption performance.
基金Projects(51505166,51871249)supported by the National Natural Science Foundation of ChinaProject(Guike AB19050002)supported by the Guangxi Key Research and Development Program,China+1 种基金Project(2020JJ2046)supported by the Hunan Science Fund for Distinguished Young Scholars,ChinaProject(2020WK2027)supported by the Hunan Key R&D Plan,China。
文摘The mechanical properties of many materials prepared by additive manufacturing technology have been greatly improved.High strength is attributed to grain refinement,formation of high density dislocation and existence of cellular structures with nanoscale during manufacturing.In addition,the super-saturated solid solution of elements in the matrix and the solid solution segregation along the wall of the cellular structures also promote the improvement of strength by enhancing dislocation pinning.Hence,the existence of cellular structure in grains leads to differences in the prediction of material strength by Hall-Petch relationship,and there is no unified calculation method to determine the d value as grain size or cell size.In this work,representative materials including austenite 316L SS were printed by selective laser melting(SLM),and the strength was predicted.The values of cell size and grain size were substituted into Hall-Petch formula,and the results showed that the calculation error for 316L is increased from 4.1%to 11.9%.Therefore,it is concluded that the strength predicted by grain size is more accurate than that predicted by cell size in additive manufacturing materials.When calculating the yield strength of laser additive manufacturing metal materials through the Hall-Petch formula,the grain size should be used as the basis for calculation.
基金Projects(2014KTZB01-02-03,2014KTZB01-02-04)supported by Shaanxi Science and Technology Coordination and Innovation Program,ChinaProject(DP120101672)supported by Australian Research Council(ARC)Discovery Grant,ARC Centre of Excellence for Design in Light Metals,Australia
文摘A yttrium-containing high-temperature titanium alloy(Ti-6Al-2.7Sn-4Zr-0.4Mo-0.45Si-0.1Y, mass fraction, %) has been additively manufactured using selective electron beam melting(SEBM). The resulting microstructure and textures were studied using scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD) and electron backscattered diffraction(EBSD) and compared with the conventionally manufactured form. A notable distinct difference of microstructures is that additive manufacturing by SEBM enables homogeneous precipitation of fine Y2O3 dispersoids in the size range of 50-250 nm throughout the as-fabricated alloy, despite the presence of just trace levels of oxygen(7×10-4, mass fraction) and yttrium(10-3, mass fraction) in the alloy. In contrast, the conventionally manufactured alloy shows inhomogeneously distributed coarse Y2O3 precipitates, including cracked or debonded Y2O3 particles.
基金Project(2020JJ2046)supported by the Science Fund for Hunan Distinguished Young Scholars,ChinaProject(S2020GXKJGG0416)supported by the Special Project for Hunan Innovative Province Construction,China+1 种基金Project(2018RS3007)supported by the Huxiang Young Talents,ChinaProject(GuikeAB19050002)supported by the Science Project of Guangxi,China。
文摘NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emphasis on its phase composition,microstructure,mechanical property and deformation mechanism.The results show that the yield strength and ductility obtained by SLM are 100 MPa and 8%,respectively,which are remarkably different from DED result with 700 MPa and 2%.The load path of SLM sample presents shape memory effect,corresponding to martensite phase detected by XRD;while the load path of DED presents pseudo-elasticity with austenite phase.In SLM sample,fine grain and hole provide a uniform deformation during tensile test,resulting in a better elongation.Furthermore,the nonequilibrium solidification was studied by a temperature field simulation to understand the difference of the two 3D printing methods.Both temperature gradient G and growth rate R determine the microstructure and phase in the SLM sample and DED sample,which leads to similar grain morphologies because of similar G/R.While higher G×R of SLM leads to a finer grain size in SLM sample,providing enough driving force for martensite transition and subsequently changing texture compared to DED sample.
基金Projects(51205335,50975242,51375411) supported by the National Natural Science Foundation of ChinaProject(2013J01209) supported by the Natural Science Foundation of Fujian Province,China
文摘A slotting method for cosine gears was proposed by using the involute cutter based on the conjugate theories of digital surface and gear meshing. The slotting model between the cosine tooth surface represented by discrete points and the cutter figuration determined by analytic function was built for their geometrical relationship and conjugate motion during the machining process. Conjugate points in the cutter section corresponding to the discrete points on the cosine gear tooth surface and the conjugate movements were solved. By using the flexible control of the CNC procedure, the active control of the cutting trace of the slotting cutter was accomplished and the envelop forming of the cosine gear was obtained. Based on the software C++ and Matlab, the computer aided manufacturing(CAM) system of the cosine gear was developed, and the simulation of the slotting process was accomplished. Several examples were provided to illustrate the approach. The result of the simulation demonstrates that the proposed slotting method is feasible.
文摘Production of ceramic armour solutions on-demand/in-theatre would have significant logistical and military advantages.However,even assuming that such technologies could be successfully deployed in the field,such near net-shape manufacturing technology is relatively immature compared to conventional sintering of ceramics.In this study,the ballistic performance of a series of additively manufactured(AM)/rapidly-prototyped(RP)alumina tiles of 97.2%of the density of Sintox FATM were investigated using both forward-and reverse-ballistic experiments.These experiments,undertaken with compressed gasguns,employed the depth-of-penetration technique and flash X-ray as primary diagnostics to interrogate both efficiency of penetration and projectile-target interaction,respectively.The RP alumina was found to exhibit useful ballistic properties,successfully defeating steel-cored(AP)7.62×39 mm BXN rounds at velocities of up-to c.a.850 m/s,while exhibiting comparable failure modes to conventionally sintered armour-grade Sintox FATM.However,where a<1%by vol.Cu dopant was introduced into the RP material failure modes changed dramatically with performance dropping below that of conventionally sintered alumina.Overall,the results from both sets of experiments were complimentary and clearly indicated the potential of such RP materials to play an active role in provision of real-world body armour solutions provided quality control of the RP material can be maintained.
文摘This paper presents the first-ever investigation of Menger fractal cubes'quasi-static compression and impact behaviour.Menger cubes with different void ratios were 3D printed using polylactic acid(PLA)with dimensions of 40 mm×40 mm×40 mm.Three different orders of Menger cubes with different void ratios were considered,namely M1 with a void ratio of 0.26,M2 with a void ratio of 0.45,and M3with a void ratio of 0.60.Quasi-static Compression tests were conducted using a universal testing machine,while the drop hammer was used to observe the behaviour under impact loading.The fracture mechanism,energy efficiency and force-time histories were studied.With the structured nature of the void formation and predictability of the failure modes,the Menger geometry showed some promise compared to other alternatives,such as foams and honeycombs.With the increasing void ratio,the Menger geometries show force-displacement behaviour similar to hyper-elastic materials such as rubber and polymers.The third-order Menger cubes showed the highest energy absorption efficiency compared to the other two geometries in this study.The findings of the present work reveal the possibility of using additively manufactured Menger geometries as an energy-efficient system capable of reducing the transmitting force in applications such as crash barriers.
基金Project(ZZYJKT2024-08)supported by the State Key Laboratory of Precision Manufacturing for Extreme Service Performance,ChinaProject(2022JB11GX004)supported by Selection of the best Candidates to Undertake Key Research Projects by Dalian City,ChinaProject(201806835007)supported by China Scholarship Council。
文摘Wire-arc additive manufacture(WAAM)has great potential for manufacturing of Al-Cu components.However,inferior mechanical properties of WAAM deposited material restrict its industrial application.Inter-layer cold rolling and thermo-mechanical heat treatment(T8)with pre-stretching deformation between solution and aging treatment were adopted in this study.Their effects on hardness,mechanical properties and microstructure were analyzed and compared to the conventional heat treatment(T6).The results show that cold rolling increases the hardness and strengths,which further increase with T8 treatment.The ultimate tensile strength(UTS)of 513 MPa and yield stress(YS)of 413 MPa can be obtained in the inter-layer cold-rolled sample with T8 treatment,which is much higher than that in the as-deposited samples.The cold-rolled samples show higher elongation than that of as-deposited ones due to significant elimination of porosity in cold rolling;while both the T6 and T8 treatments decrease the elongation.The cold rolling and pre-stretching deformation both contribute to the formation of dense and dispersive precipitatedθ′phases,which inhibits the dislocation movement and enhances the strengths;as a result,T8 treatment shows better strengthening effect than the T6 treatment.The strengthening mechanism was analyzed and it was mainly related to work hardening and precipitation strengthening.
基金funded by the National Natural Science Foundation of China Youth Fund(Grant No.62304022)Science and Technology on Electromechanical Dynamic Control Laboratory(China,Grant No.6142601012304)the 2022e2024 China Association for Science and Technology Innovation Integration Association Youth Talent Support Project(Grant No.2022QNRC001).
文摘Metal Additive Manufacturing(MAM) technology has become an important means of rapid prototyping precision manufacturing of special high dynamic heterogeneous complex parts. In response to the micromechanical defects such as porosity issues, significant deformation, surface cracks, and challenging control of surface morphology encountered during the selective laser melting(SLM) additive manufacturing(AM) process of specialized Micro Electromechanical System(MEMS) components, multiparameter optimization and micro powder melt pool/macro-scale mechanical properties control simulation of specialized components are conducted. The optimal parameters obtained through highprecision preparation and machining of components and static/high dynamic verification are: laser power of 110 W, laser speed of 600 mm/s, laser diameter of 75 μm, and scanning spacing of 50 μm. The density of the subordinate components under this reference can reach 99.15%, the surface hardness can reach 51.9 HRA, the yield strength can reach 550 MPa, the maximum machining error of the components is 4.73%, and the average surface roughness is 0.45 μm. Through dynamic hammering and high dynamic firing verification, SLM components meet the requirements for overload resistance. The results have proven that MEM technology can provide a new means for the processing of MEMS components applied in high dynamic environments. The parameters obtained in the conclusion can provide a design basis for the additive preparation of MEMS components.
基金sponsored by the National Key Research and Development Program of China(Grant No.2022YFC3320500)the National Natural Science Foundation of China(Grant Nos.12372333,12221002 and 12072037)。
文摘According to different damage modes,warheads are roughly divided into three types:fragmentation warheads,shaped charge warheads,and penetrating warheads.Due to limitations in material and structural manufacturing,traditional manufacturing methods make it difficult to fully utilize the damage ability of the warhead.Additive manufacturing(AM)technology can fabricate complex structures,with classified materials composition and customized components,while achieving low cost,high accuracy,and rapid production of the parts.The maturity of AM technology has brought about a new round of revolution in the field of warheads.In this paper,we first review the principles,classifications,and characteristics of different AM technologies.The development trends of AM technologies are pointed out,including multi-material AM technology,hybrid AM technology,and smart AM technology.From our survey,PBF,DED,and EBM technologies are mainly used to manufacture warhead damage elements.FDM and DIW technologies are mainly used to manufacture warhead charges.Then,the research on the application of AM technology in three types of warhead and warhead charges was reviewed and the existing problems and progress of AM technologies in each warhead were analyzed.Finally,we summarized the typical applications and look forward to the application prospects of AM technology in the field of warheads.
文摘Because of an unfortunate mistake during the production of this article,the Acknowledgements have been omitted.The Acknowledgements are added as follows:Sasan YAZDANI would like to thank the Scientific and Technological Research Council of Turkey(TÜB˙ITAK)for receiving financial support for this work through the 2221 Fellowship Program for Visiting Scientists and Scientists on Sabbatical Leave(Grant ID:E 21514107-115.02-228864).Sasan YAZDANI also expresses his gratitude to Sahand University of Technology for granting him sabbatical leave to facilitate the completion of this research.
基金Generalitat Valenciana(GVA)and Spanish Ministry of Science and Innovation(Grant Nos.TED2021-130879 B-C21,CIACIF/2021/286,PID2023-151110OB-I00,and CIPROM/2022/3)to provide funds for conducting experiments and software licensessupported by the National Research Foundation,Prime Minister's Office,Singapore under its Campus for Research Excellence and Technological Enterprise(CREATE)programme。
文摘Military missions in hostile environments are often costly and unpredictable,with squadrons sometimes facing isolation and resource scarcity.In such scenarios,critical components in vehicles,drones,and energy generators may require structural reinforcement or repair due to damage.This paper proposes a portable,on-site production method for molds under challenging conditions,where material supply is limited.The method utilizes large format additive manufacturing(LFAM)with recycled composite materials,sourced from end-of-life components and waste,as feedstock.The study investigates the microstructural effects of recycling through shredding techniques,using microscopic imaging.Three potential defense-sector applications are explored,specifically in the aerospace,automotive,and energy industries.Additionally,the influence of key printing parameters,particularly nonparallel plane deposition at a 45-degree angle,on the mechanical behavior of ABS reinforced with 20%glass fiber(GF)is examined.The results demonstrate the feasibility of this manufacturing approach,highlighting reductions in waste material and production times compared to traditional methods.Shorter layer times were found to reduce thermal gradients between layers,thereby improving layer adhesion.While 45-degree deposition enhanced Young's modulus,it slightly reduced interlayer adhesion quality.Furthermore,recycling-induced fiber length reduction led to material degradation,aligning with findings from previous studies.Challenges encountered during implementation included weak part adherence to the print bed and local excess material deposition.Overall,the proposed methodology offers a cost-effective alternative to traditional CNC machining for mold production,demonstrating its potential for on-demand manufacturing in resource-constrained environments.
文摘The present work explores the feasibility of fabricating porous 3D parts in TiAl intermetallic alloy directly from Tie6Ale4V and Al powders. This approach uses a binder jetting additive manufacturing process followed by reactive sintering. The results demonstrate that the present approach is successful for realizing parts in TiAl intermetallic alloy.
文摘Pursuing the green manufacturing (GM) of products i s very beneficial in the alleviation of environment burdens. In order to reap such benefits, green manufacturing is involved in every aspect of manufacturing proc esses. During the machining process, cutting fluid is one of the main roots of e nvironmental pollution. And how to make an optimal selection for cutting fluid f or GM is an important path to reduce the environmental pollution. The objective factors of decision-making problems in the traditional selection of cutting flu id are usually two: quality and cost. But from the viewpoint of GM, environmenta l impact (E) should be considered together. In this paper, a multi-object d ecision-making model of cutting fluid selection for GM is put forward, in which the objects of Quality (Q), Cost(C) and Environmental impact (E) are considered together. In this model, E means to minimize the environmental impact, Q means to maximize the quality and C means to minimize the cost. Each objective is anal yzed in detail too. A case study on a decision-making problem of cutting fluid selection in a gear hobbing process is analyzed, and the result shows the model is practical.
文摘Achieving sustainable patterns of consumption and production is perhaps the biggest challenge facing our society today. The de-mand for more safe environmentally benign products is rising and many companies are looking for new ways to progressively improve the sus-tainability of their products. Moreover, there are numerous opportunities and countless innovations, technological as well as non-technologi-cal,that need to be exploited to improve the sustainability of products. Manufacturing industry is an important sector of any economy and hasthe potential to become a driving force for enabling sustainable patterns of production and consumption through introducing efficient productionpractices and developing products and services that help reduce environmental impacts. The benefits of adopting an integrated policy towardsproduct development based on life cycle thinking and eco-design to stimulate improvement of the environmental performance of each part ofproduct life cycle phases and achieve sustainable patterns of production and consumption are emphasized. The challenges in implementingsustainable manufacturing and the circular economy approaches are listed. A number of solutions are suggested to face up these challenges,for instance, increased awareness of enterprises particularly SME's of product life cycle issues and the opportunities that are available for costsavings and profit making from eco-innovation in product development for both the domestic and export markets and providing practical helpand advice directly to enterprises on integrated product development to promote enterprise led Eco-innovation. Aiming at contributing to sus-tainable manufacturing in China, Sino-UK Low Carbon Manufacturing Consortium, a multi-disciplinary research and educational partnershipbetween academia, industry and government agencies in the UK and China with interest in sustainable manufacturing issues, has been formedrecently.The vision, aims and benefits of membership of the consortium are also discussed.
基金Project(51922108)supported by the National Natural Science Foundation of ChinaProject(2019JJ20031)supported by Hunan Natural Science Foundation,ChinaProject(2019SK2061)supported by Hunan Key Research and Development Program,China。
文摘Additive manufacturing is a new emerging technology which is ideal for low-to-zero waste production, and it is considered to be a green and clean process that has the potential to lower the cost and energy consumption of production. However, the cost of the feedstock for additive manufacturing and the additive manufactured parts is usually very high, which hinders the further application of additive manufacturing, especially for the metal additive manufacturing. The concept of circular metal additive manufacturing involves the recycling of the metal feedstock and the additive manufactured parts leading to the truly zero waste production and the most energy saving. This paper reviews the technologies that help the formation of a circular metal additive manufacturing through recycling of the feedstocks and the damaged metal parts. Reactive metals, such as titanium, tend to be contaminated easily during handling and production. Recycling of the titanium for achieving a circular titanium additive manufacturing is reviewed in detail.
基金supported by the National High-Tech R&D Program,China(2015AA042101)
文摘Cloud manufacturing is a specific implementation form of the "Internet + manufacturing" strategy. Why and how to develop cloud manufacturing platform(CMP), however, remains the key concern of both platform operators and users. A microscopic model is proposed to investigate advantages and diffusion forces of CMP through exploration of its diffusion process and mechanism. Specifically, a three-stage basic evolution process of CMP is innovatively proposed. Then, based on this basic process, a more complex CMP evolution model has been established in virtue of complex network theory, with five diffusion forces identified. Thereafter, simulations on CMP diffusion have been conducted. The results indicate that, CMP possesses better resource utilization,user satisfaction, and enterprise utility. Results of simulation on impacts of different diffusion forces show that both the time required for CMP to reach an equilibrium state and the final network size are affected simultaneously by the five diffusion forces. All these analyses indicate that CMP could create an open online cooperation environment and turns out to be an effective implementation of the "Internet + manufacturing" strategy.
基金supported by the National Natural Science Foundation of China(71401131)the MOE(Ministry of Education in China)Project of Humanities and Social Sciences(13XJC630011)the Ministry of Education Research Fund for the Doctoral Program of Higher Education(20120184120040)
文摘How to deal with the collaboration between task decomposition and task scheduling is the key problem of the integrated manufacturing system for complex products. With the development of manufacturing technology, we can probe a new way to solve this problem. Firstly, a new method for task granularity quantitative analysis is put forward, which can precisely evaluate the task granularity of complex product cooperation workflow in the integrated manufacturing system, on the above basis; this method is used to guide the coarse-grained task decomposition and recombine the subtasks with low cohesion coefficient. Then, a multi-objective optimieation model and an algorithm are set up for the scheduling optimization of task scheduling. Finally, the application feasibility of the model and algorithm is ultimately validated through an application case study.
