The gears of new energy vehicles are required to withstand higher rotational speeds and greater loads,which puts forward higher precision essentials for gear manufacturing.However,machining process parameters can caus...The gears of new energy vehicles are required to withstand higher rotational speeds and greater loads,which puts forward higher precision essentials for gear manufacturing.However,machining process parameters can cause changes in cutting force/heat,resulting in affecting gear machining precision.Therefore,this paper studies the effect of different process parameters on gear machining precision.A multi-objective optimization model is established for the relationship between process parameters and tooth surface deviations,tooth profile deviations,and tooth lead deviations through the cutting speed,feed rate,and cutting depth of the worm wheel gear grinding machine.The response surface method(RSM)is used for experimental design,and the corresponding experimental results and optimal process parameters are obtained.Subsequently,gray relational analysis-principal component analysis(GRA-PCA),particle swarm optimization(PSO),and genetic algorithm-particle swarm optimization(GA-PSO)methods are used to analyze the experimental results and obtain different optimal process parameters.The results show that optimal process parameters obtained by the GRA-PCA,PSO,and GA-PSO methods improve the gear machining precision.Moreover,the gear machining precision obtained by GA-PSO is superior to other methods.展开更多
介绍了STEP-NC的概念、数据模型及其结构特点,然后通过对比MLP(Machining Line Planner)和STEP-NC数控程序对特征和操作的不同定义方法,分析了在MLP中特征及加工工艺与STEP-NC的对应关系,探讨了在MLP中实现输出STEP-NC格式的零件加工程...介绍了STEP-NC的概念、数据模型及其结构特点,然后通过对比MLP(Machining Line Planner)和STEP-NC数控程序对特征和操作的不同定义方法,分析了在MLP中特征及加工工艺与STEP-NC的对应关系,探讨了在MLP中实现输出STEP-NC格式的零件加工程序的方法。展开更多
The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was develo...The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was developed to predict the shape evolution during the ECM by mask.The current density distribution is sensitive to mask wall angle.The evolution of cavity is determined by the current density distribution of evolving workpiece surface.The maximum depth is away from the center of holes machined,which leads to the island appearing at the center of cavity for mask wall angles greater than or equal to 90°(β≥90°).The experimental system was established and the simulation results were experimentally verified.The results indicate that the simulation results of cavity shape are consistent with the actual ones.The experiments also show that the repetition accuracy of matrix-hole for β≥90° is higher than that for β<90°.A hole taper is diminished,and the machining accuracy is improved with the mask wall angle increasing.展开更多
Powder Mixed Electric Discharge Machining (PMEDM) has different mechanism from conventional EDM, which can improve the surface roughness and surface quality distinctly and to obtain nearly mirror surface effects. It i...Powder Mixed Electric Discharge Machining (PMEDM) has different mechanism from conventional EDM, which can improve the surface roughness and surface quality distinctly and to obtain nearly mirror surface effects. It is a useful finish machining method and is researched and applied by many countries. However there are little research on rough machining of PMEDM. Experiments show that PMEDM machining makes discharge breakdown easier, enlarges the discharge gaps and widens discharge passage, and at last forms even distributed and "large and shadow" shaped etched cavities. Because of much loss of discharge energy in the discharge gaps and reduction of ejecting force on the melted material, the machining efficiency gets lower and the surface roughness gets small in PMEDM machining in comparison with conventional EDM machining. This paper performs experimental research on the machining efficiency and surface roughness of PMEDM in rough machining. The machining efficiency of PMEDM can be highly increased by selecting proper discharge parameters (increasing peak current, reducing pulse width) with approximate surface roughness in comparison with conventional EDM machining. Although PMEDM can improve machining efficiency in rough efficiency, but a series of problems like electrode wear, efficiently separation of machined scraps from the powder mixed working fluid, should be solved before PMEDM machining is really applied in rough machining. Experiments result shows that powder mixed EDM machining can obviously improve machining efficiency at the same surface roughness by selecting proper discharging parameters, and can provide reference accordingly for the application of PMEDM machining technology in rough machining.展开更多
Electrochemical machining (ECM) is one of the best al ternatives for producing complex shapes in advanced materials used in aircraft a nd aerospace industries. However, the reduction of the stray material removal co n...Electrochemical machining (ECM) is one of the best al ternatives for producing complex shapes in advanced materials used in aircraft a nd aerospace industries. However, the reduction of the stray material removal co ntinues to be major challenges for industries in addressing accuracy improvement . This study presents a method of improving machining accuracy in ECM by using a dual pole tool with a metallic bush outside the insulated coating of a cathode tool. The bush is connected with anode and so the electric field at the side gap area is substantially weakened. The modeling and simulation indicate that the p ositive bush brings down the current density at the side gap area of the machine d hole and hence reduces the stray material removal there. It has been experimen tally observed that the machining accuracy and the process stability are signifi cantly improved.展开更多
The Al 2O 3 particles reinforced aluminum matrix composite (Al 2O 3p/Al) are more and more widely used for their excellent physical and chemical properties. However, their poor machinability leads to severe tool wear ...The Al 2O 3 particles reinforced aluminum matrix composite (Al 2O 3p/Al) are more and more widely used for their excellent physical and chemical properties. However, their poor machinability leads to severe tool wear and bad machined surface. In this paper laser assisted machining is adopted in machining Al 2O 3p/Al composite and good result was obtained. The result of experiment shows in machining Al 2O 3p/Al composites the cutting force is reduced in 30%～50%, the tool wear is reduced in 20%～30% and machined surface quality is improved in laser assisted machining as compared with conventional cutting. The physical model of the cutting process is set up and explains the reason why the cutting forced are reduced. The state of the particles is the main influence of the change. When the material of cutting zone is heating by laser, the aluminum matrix becomes softer and easier in plastic deformation, which leads to the reduction of the pushing force from the tool to the machined surface. The soften aluminum matrix is more easy to be squeezed out from the machined surface, and it leads the concentration of the Al 2O 3 particles in the surface layer of machined surface. The softening effect of laser heating on aluminum matrix reduces the pushing forces of the Al 2O 3 particles on the clearance face of cutting tool, which is just the reason for the severe cutting tool wear in conventional machining of Al 2O 3p/Al composite. Because the Al 2O 3 particles were pushed in during the cutting process, the particles increased in the surface layer. Because of the difference in thermal conductivity and thermal expansion between the Al-matrix and Al 2O 3 particle, residual stress is changed in the matrix after machining due to the extrusion of the tool, deformation of the matrix and displacement of the Al 2O 3 particle in the matrix. Temperature gradient comes into the cutting zone and the work-piece surface layer, it will lead to the increase of thermal stress and misfit dislocation in the matrix. The residual stress is compressive in the laser assisted hot cutting surface, the compressive stress is nearly triple times than that in the conventional cutting surface. Some analysis on the mechanism of laser heat assisted machining of Al 2O 3p/Al composite is given in the paper too.展开更多
For electro-discharge machining, only in the optimum state could the highest material removal rate be realized. In practical machining process, the timely elevation of the tool electrode is needed to eliminate chippin...For electro-discharge machining, only in the optimum state could the highest material removal rate be realized. In practical machining process, the timely elevation of the tool electrode is needed to eliminate chipping, which ordinarily occupies quite a lot of time. Therefore, besides the control of the machining parameters, the control of the optimum discharge gap and the conversion of different machining states is also needed. In this paper, the adaptive fuzzy control system of servomechanism for EDM combined with ultrasonic vibration is studied, the servomechanism of which is composed of the stepping motor comprising variable steps and the inductive synchronizer. The fuzzy control technology is used to realize the control of the frequency and the step of the servomechanism. The adaptive fuzzy controller has three inputs and two outputs, which can well meet the actual control requirements. The constitution of the fuzzy control regulation for the step frequency is the key to the design of the whole fuzzy control system of the servomechanism. The step frequency is mainly determined by the position error and the change rate of the position error. When the value of the position error is high or medium, the controlled parameters are selected to eliminate the error; when the position error is lower, the controlled parameters are selected to avoid the over-orientation and thus keep the stability of the system. According to these, a fuzzy control table is established in advanced, which is used to express the relations between the fuzzy input parameters and the fuzzy output parameters. The input parameters and the output parameters are all expressed by the level-values in fuzzy field. Therefore, the output parameters used for control can be obtained for the fuzzy control table according to the detected actual input parameters, by which the EDM combined with ultrasonic vibration is improved and the machining efficiency is increased. In addition, a stimulation program is designed by means of Microsoft Visual Basic展开更多
In this study, a newly developed titanium superalloy, i.e., the Ti-5553 alloy has used for hot machining. This material replaced Ti-grade-5 alloy in the application of aerospace, automobile, and biomedical sector. How...In this study, a newly developed titanium superalloy, i.e., the Ti-5553 alloy has used for hot machining. This material replaced Ti-grade-5 alloy in the application of aerospace, automobile, and biomedical sector. However, similar to Ti-grade-5 alloy, the Ti-5553 alloy has a low thermal conductivity which makes it difficult-to-cut material categories hence, high tool wear, cutting force and bad surface finish. Hot machining of Ti-5553 has been studied at different machining condition (room and hot) using Deform-2D finite element analysis. The result from the simulation test was compared with the experimental value and reduction of cutting and thrust forces was observed. The experiment was carried out with the same input parameters as simulation, and good coherence between them observed. Additionally, cutting zone temperature, effective stress, etc. for both room and elevated the temperature are also discussed.展开更多
An impeller is difficult to machine because of severe collision due to the complex shape,overlapping and twisted shape of the impeller blades.So,most computer aided manufacturing(CAM)software companies have developed ...An impeller is difficult to machine because of severe collision due to the complex shape,overlapping and twisted shape of the impeller blades.So,most computer aided manufacturing(CAM)software companies have developed CAM module for manufacturing impeller according to their CAM software.But these dedicated modules are difficult to use for inexperienced users.The purpose of this work is to develop a tool-path generation module for impellers.For this purpose,it is based on Visual Basic language and used CATIA graphical environment.The result of simulation for generated tool-path by the module is satisfactory.And it has slow processing speed compared to other commercial modules,but it is easy to use.展开更多
This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface wi...This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.展开更多
The investigation was carried out on the technical problems of finishing the inner surface of elbow parts and the action mechanism of particles in elbow precision machining by abrasive flow.This work was analyzed and ...The investigation was carried out on the technical problems of finishing the inner surface of elbow parts and the action mechanism of particles in elbow precision machining by abrasive flow.This work was analyzed and researched by combining theory,numerical and experimental methods.The direct simulation Monte Carlo(DSMC)method and the finite element analysis method were combined to reveal the random collision of particles during the precision machining of abrasive flow.Under different inlet velocity,volume fraction and abrasive particle size,the dynamic pressure and turbulence flow energy of abrasive flow in elbow were analyzed,and the machining mechanism of particles on the wall and the influence of different machining parameters on the precision machining quality of abrasive flow were obtained.The test results show the order of the influence of different parameters on the quality of abrasive flow precision machining and establish the optimal process parameters.The results of the surface morphology before and after the precision machining of the inner surface of the elbow are discussed,and the surface roughness Ra value is reduced from 1.125μm to 0.295μm after the precision machining of the abrasive flow.The application of DSMC method provides special insights for the development of abrasive flow technology.展开更多
The electric double layer with the transmission of particles was presented based on the principle of electrochemistry.In accordance with this theory,the cavitation catalysis removal mechanism of ultrasonic-pulse elect...The electric double layer with the transmission of particles was presented based on the principle of electrochemistry.In accordance with this theory,the cavitation catalysis removal mechanism of ultrasonic-pulse electrochemical compound machining(UPECM) based on particles was proposed.The removal mechanism was a particular focus and was thus validated by experiments.The principles and experiments of UPECM were introduced,and the removal model of the UPECM based on the principles of UPECM was established.Furthermore,the effects of the material removal rate for the main processing parameters,including the particles size,the ultrasonic vibration amplitude,the pulse voltage and the minimum machining gap between the tool and the workpiece,were also studied through UPECM.The results show that the particles promote ultrasonic-pulse electrochemical compound machining and thus act as the catalyzer of UPECM.The results also indicate that the processing speed,machining accuracy and surface quality can be improved under UPECM compound machining.展开更多
For laser assisted machining,shape of preheating laser heat source is changed irregularly because of complexity of material shape.So,the preheating temperature should be controlled by adjusting the feed rate or the la...For laser assisted machining,shape of preheating laser heat source is changed irregularly because of complexity of material shape.So,the preheating temperature should be controlled by adjusting the feed rate or the laser power.Thermal analyses of the laser assisted machining process for inclination planes were performed.By analyzing the obtained temperature profile,a proper feed rate control method was proposed according to the inclination angles.In addition,the temperature distribution of the cross section after feed rate control was predicted.The correlation equation between inclination angles and adjusted proper feed rate was proposed.The results of this analysis can be used to predict the preheating effect on workpiece and can be applied as a preheating temperature control method in laser assisted machining processes.展开更多
Wire electric discharge machining(WEDM)process is used for precision manufacturing.The accuracy of machining is function of various parameters like current,voltage,wire speed,gap between wire and work piece,wire oscil...Wire electric discharge machining(WEDM)process is used for precision manufacturing.The accuracy of machining is function of various parameters like current,voltage,wire speed,gap between wire and work piece,wire oscillation,work material,wire material,etc.Once the process parameters are selected,it is important that the wire vibrations are less to obtain a good surface finish.Due to the importance of wire vibration in obtaining the surface finish,it is necessary to study the wire vibration.This paper discusses different models of wire vibration presented in the literature and simulates a closed form solution of wire vibration using MATLAB.The transverse vibration of wire is analysed as forced vibration of moving wire with excitation due to the sparks during machining.The resulting partial differential equation is solved by using finite difference method and vibration is also simulated in the finite element package‘ANSYS’.The wire behaviour is investigated under different operating conditions and results of the two methods are展开更多
During five-axis machining of impeller, the excessive local interference avoidance leads to inconsistency of cutter posture, low quality of machined surface and increase of processing time. Therefore, in order to impr...During five-axis machining of impeller, the excessive local interference avoidance leads to inconsistency of cutter posture, low quality of machined surface and increase of processing time. Therefore, in order to improve the efficiency of five-axis machining of impellers, it is necessary to minimize the cutter posture changes and create a continuous tool path while avoiding interference. By using an MC-space algorithm for interference avoidance, an MB-spline algorithm for continuous control was intended to create a five-axis machining tool path with excellent surface quality and economic feasibility. A five-axis cutting experiment was performed to verify the effectiveness of the continuity control. The result shows that the surface shape with continuous method is greatly improved, and the surface roughness is generally favorable. Consequently, the effectiveness of the suggested method is verified by identifying the improvement of efficiency of five-axis machining of an impeller in aspects of surface quality and machining time.展开更多
Ultrasonic machining (USM) is considered as an effective method for machining hard and brittle materials such as glass, engineering ceramics, semiconductors, diamonds, metal composites and so on. However, the low mate...Ultrasonic machining (USM) is considered as an effective method for machining hard and brittle materials such as glass, engineering ceramics, semiconductors, diamonds, metal composites and so on. However, the low material removal rate due to using abrasive slurry limits further application of USM. Rotary ultrasonic machining (rotary USM) superimposes rotational movement on the tool head that vibrates at ultrasonic frequency (20 kHz) simultaneously. The tool is made of mild steel coated or bonded with diamond abrasive. Therefore, abrasive slurry is abandoned and coolant is used to carry debris out of working area. Compared with USM, rotary USM can obtain much higher material removal rate, deep holes, and fine precision, which leads to its further application. Combined with CNC technology, rotary USM can be used to conduct contour machining of hard and brittle materials. In this paper, the movement of abrasive particles in tool tip of rotary ultrasonic machining is analyzed. The impacting and grinding of abrasive in tool tip to machined surface are considered as main factors to material removal rate. The process of crack forming and growing in one loading and unloading cycle can be described as following stages: a) When abrasive particle acts the pressure on work-piece, the macro cracks in periphery of contact area are exerted increasing tensile stress. b) As the tensile stress increase to the critical of material tension, the one of cracks in periphery of contact area begins to propagate around contact area and develop beneath the surface to certain depth. c) Indentation area varies with increasing of load, the circle crack around contact area steadily or dynamical propagates towards inside of work-piece. d) As tensile stress in crack increases to critical of crack steady failure, circle crack suddenly becomes conic crack. e) Further increase load, the crack continues to grow while contact area is surrounded by conic cracks. f) During unloading, conic crack begins to close, some of cracks continue their extension towards the surface and forms a circle groove. The mathematical model for material removal rate shows that the factors affecting on material removal rate are static load, grid and concentration of abrasive, mechanical properties of machined materials, rotational speed of tool and feed speed of work-piece.展开更多
As the cutting speed goes higher, the mechanism of chip deformation will be changed significantly, i.e., continuous chip in low cutting speed will shift to serrated chip with shear localization. For the shear localize...As the cutting speed goes higher, the mechanism of chip deformation will be changed significantly, i.e., continuous chip in low cutting speed will shift to serrated chip with shear localization. For the shear localized chip, the parameters used to assess the chip deformation for continuous chip, such as shorten coefficient ξ, shear angle φ and shear strain ε, can not describe the chip deformation correctly or comprehensively. This paper deals with the assessment of chip deformation of shear localization. There are two deformation regions in shear localized chip, one is the chip segment body with relative smaller plastic deformation, another one is the boundary between segments with shear localization, so called shear band. Considering the two distinct deformation regions, two parameters are used to define their deformation respectively. According to the analysis of chip formation process, the equations have been deduced to calculate the shear strains of shear band ε, shear strain of chip segment ε 1 and shear rate so that the shear localized chip deformation can be assessed correctly and comprehensively. By use of this assessment, the chip deformation in machining selenium treated stainless steel (STSS) and common stainless steel at various cutting conditions is investigated. The experiment results obtained by the machining of stainless steel prove that: (1) the shear strain and strain rate increase with the increasing of cutting speed; (2) the shear strain in shear band can be over 10 when cutting speed exceeding 200 m/min for both types of stainless steel, and it is much higher than the strain of chip segment. The difference will be enlarged as the cutting speed increasing; (3) As the comparison, the shear strain for the STSS is a little lower than that for JIS304; (4) The stain rate is extremely high (= 2.5×10 5 1/s ). In range of cutting speed less than 180 m/min, the strain rate for STSS is lower than that for JIS304. However, when the cutting speed is higher than 180 m/min, the strain rate for STSS is higher than that for JIS304.展开更多
In the process of numerical control machining simulation,the workpiece surface is usually described with the uniform triangular mesh model.To alleviate the contradiction between the simulation speed and accuracy in th...In the process of numerical control machining simulation,the workpiece surface is usually described with the uniform triangular mesh model.To alleviate the contradiction between the simulation speed and accuracy in this model,two improved methods,i.e.,the local refinement triangular mesh modeling method and the adaptive triangular mesh modeling method were presented.The simulation results show that when the final shape of the workpiece is known and its mathematic representation is simple,the local refinement triangular mesh modeling method is preferred;when the final shape of the workpiece is unknown and its mathematic description is complicated,the adaptive triangular mesh modeling method is more suitable.The experimental results show that both methods are more targeted and practical and can meet the requirements of real-time and precision in simulation.展开更多
This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes...This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes are involved simultaneously i.e.spark erosion,chemical etching,and abrasive grinding for removal of material while the classical electrochemical discharge machining process involves double actions i.e.spark erosion,and chemical etching.The powder-mixed electrolyte process resulted in rapid material removal along with a better surface finish as compared to the classical microelectrochemical discharge machining(MECDM).Further,the results are optimized through a multiobjective optimization approach and study of the surface topography of the hole wall surface obtained at optimized parameters.In the selected range of experimental parameters,PMECDM shows a higher material removal rate(MRR) and lower surface roughness(R_(a))(MRR:2.8 mg/min and R_(a) of 0.61 μm) as compared to the MECDM process(MRR:2.01 mg/min and corresponding Raof 1.11 μm).A detailed analysis of the results is presented in this paper.展开更多
Laser-assisted machining has been considered as a new alternative machining method of difficult-to-cut materials. A laser module with one-axis manipulator is developed to focus on preheating laser beam effectively. Fi...Laser-assisted machining has been considered as a new alternative machining method of difficult-to-cut materials. A laser module with one-axis manipulator is developed to focus on preheating laser beam effectively. First of all, the thermal characteristic analysis was performed to verify the importance of laser module location. Laser module should be moved within 1 mm. Analysis conditions of three positions in driving range of the one-axis manipulator are selected. And a C coupling is used as a connection device for spindle and laser module. An initial model has one C coupling, and the number of C coupling has been increased from 1 to 2 in an improved model. And the analysis is carried out again for the one-axis manipulator. The results of the static analysis, the maximum displacement and the maximum stress are decreased by 22% and 11%, respectively, for the improved model when the laser module is located at farthest away from the spindle unit. As a result of the modal analysis, the first natural frequency mode is increased by 13%, 18% and 12% at these positions of the improved model, respectively. The harmonic analysis of the improved model was performed by analyzing the results of the modal analysis. The maximum deformation was 0.33 mm in driving unit at 222 Hz. And the maximum compliance of the ISO axis direction was 0.23 mm/N. Finally, the one-axis manipulator has been fabricated successfully using the analysis result.展开更多
基金Projects(U22B2084,52275483,52075142)supported by the National Natural Science Foundation of ChinaProject(2023ZY01050)supported by the Ministry of Industry and Information Technology High Quality Development,China。
文摘The gears of new energy vehicles are required to withstand higher rotational speeds and greater loads,which puts forward higher precision essentials for gear manufacturing.However,machining process parameters can cause changes in cutting force/heat,resulting in affecting gear machining precision.Therefore,this paper studies the effect of different process parameters on gear machining precision.A multi-objective optimization model is established for the relationship between process parameters and tooth surface deviations,tooth profile deviations,and tooth lead deviations through the cutting speed,feed rate,and cutting depth of the worm wheel gear grinding machine.The response surface method(RSM)is used for experimental design,and the corresponding experimental results and optimal process parameters are obtained.Subsequently,gray relational analysis-principal component analysis(GRA-PCA),particle swarm optimization(PSO),and genetic algorithm-particle swarm optimization(GA-PSO)methods are used to analyze the experimental results and obtain different optimal process parameters.The results show that optimal process parameters obtained by the GRA-PCA,PSO,and GA-PSO methods improve the gear machining precision.Moreover,the gear machining precision obtained by GA-PSO is superior to other methods.
基金Project(50635040) supported by the National Natural Science Foundation of ChinaProject(2009AA044205) supported by the National High Technology Research and Development ProgramProject(BK2008043) supported by the Jiangsu Provincial Natural Science Foundation,China
文摘The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was developed to predict the shape evolution during the ECM by mask.The current density distribution is sensitive to mask wall angle.The evolution of cavity is determined by the current density distribution of evolving workpiece surface.The maximum depth is away from the center of holes machined,which leads to the island appearing at the center of cavity for mask wall angles greater than or equal to 90°(β≥90°).The experimental system was established and the simulation results were experimentally verified.The results indicate that the simulation results of cavity shape are consistent with the actual ones.The experiments also show that the repetition accuracy of matrix-hole for β≥90° is higher than that for β<90°.A hole taper is diminished,and the machining accuracy is improved with the mask wall angle increasing.
文摘Powder Mixed Electric Discharge Machining (PMEDM) has different mechanism from conventional EDM, which can improve the surface roughness and surface quality distinctly and to obtain nearly mirror surface effects. It is a useful finish machining method and is researched and applied by many countries. However there are little research on rough machining of PMEDM. Experiments show that PMEDM machining makes discharge breakdown easier, enlarges the discharge gaps and widens discharge passage, and at last forms even distributed and "large and shadow" shaped etched cavities. Because of much loss of discharge energy in the discharge gaps and reduction of ejecting force on the melted material, the machining efficiency gets lower and the surface roughness gets small in PMEDM machining in comparison with conventional EDM machining. This paper performs experimental research on the machining efficiency and surface roughness of PMEDM in rough machining. The machining efficiency of PMEDM can be highly increased by selecting proper discharge parameters (increasing peak current, reducing pulse width) with approximate surface roughness in comparison with conventional EDM machining. Although PMEDM can improve machining efficiency in rough efficiency, but a series of problems like electrode wear, efficiently separation of machined scraps from the powder mixed working fluid, should be solved before PMEDM machining is really applied in rough machining. Experiments result shows that powder mixed EDM machining can obviously improve machining efficiency at the same surface roughness by selecting proper discharging parameters, and can provide reference accordingly for the application of PMEDM machining technology in rough machining.
文摘Electrochemical machining (ECM) is one of the best al ternatives for producing complex shapes in advanced materials used in aircraft a nd aerospace industries. However, the reduction of the stray material removal co ntinues to be major challenges for industries in addressing accuracy improvement . This study presents a method of improving machining accuracy in ECM by using a dual pole tool with a metallic bush outside the insulated coating of a cathode tool. The bush is connected with anode and so the electric field at the side gap area is substantially weakened. The modeling and simulation indicate that the p ositive bush brings down the current density at the side gap area of the machine d hole and hence reduces the stray material removal there. It has been experimen tally observed that the machining accuracy and the process stability are signifi cantly improved.
文摘The Al 2O 3 particles reinforced aluminum matrix composite (Al 2O 3p/Al) are more and more widely used for their excellent physical and chemical properties. However, their poor machinability leads to severe tool wear and bad machined surface. In this paper laser assisted machining is adopted in machining Al 2O 3p/Al composite and good result was obtained. The result of experiment shows in machining Al 2O 3p/Al composites the cutting force is reduced in 30%～50%, the tool wear is reduced in 20%～30% and machined surface quality is improved in laser assisted machining as compared with conventional cutting. The physical model of the cutting process is set up and explains the reason why the cutting forced are reduced. The state of the particles is the main influence of the change. When the material of cutting zone is heating by laser, the aluminum matrix becomes softer and easier in plastic deformation, which leads to the reduction of the pushing force from the tool to the machined surface. The soften aluminum matrix is more easy to be squeezed out from the machined surface, and it leads the concentration of the Al 2O 3 particles in the surface layer of machined surface. The softening effect of laser heating on aluminum matrix reduces the pushing forces of the Al 2O 3 particles on the clearance face of cutting tool, which is just the reason for the severe cutting tool wear in conventional machining of Al 2O 3p/Al composite. Because the Al 2O 3 particles were pushed in during the cutting process, the particles increased in the surface layer. Because of the difference in thermal conductivity and thermal expansion between the Al-matrix and Al 2O 3 particle, residual stress is changed in the matrix after machining due to the extrusion of the tool, deformation of the matrix and displacement of the Al 2O 3 particle in the matrix. Temperature gradient comes into the cutting zone and the work-piece surface layer, it will lead to the increase of thermal stress and misfit dislocation in the matrix. The residual stress is compressive in the laser assisted hot cutting surface, the compressive stress is nearly triple times than that in the conventional cutting surface. Some analysis on the mechanism of laser heat assisted machining of Al 2O 3p/Al composite is given in the paper too.
文摘For electro-discharge machining, only in the optimum state could the highest material removal rate be realized. In practical machining process, the timely elevation of the tool electrode is needed to eliminate chipping, which ordinarily occupies quite a lot of time. Therefore, besides the control of the machining parameters, the control of the optimum discharge gap and the conversion of different machining states is also needed. In this paper, the adaptive fuzzy control system of servomechanism for EDM combined with ultrasonic vibration is studied, the servomechanism of which is composed of the stepping motor comprising variable steps and the inductive synchronizer. The fuzzy control technology is used to realize the control of the frequency and the step of the servomechanism. The adaptive fuzzy controller has three inputs and two outputs, which can well meet the actual control requirements. The constitution of the fuzzy control regulation for the step frequency is the key to the design of the whole fuzzy control system of the servomechanism. The step frequency is mainly determined by the position error and the change rate of the position error. When the value of the position error is high or medium, the controlled parameters are selected to eliminate the error; when the position error is lower, the controlled parameters are selected to avoid the over-orientation and thus keep the stability of the system. According to these, a fuzzy control table is established in advanced, which is used to express the relations between the fuzzy input parameters and the fuzzy output parameters. The input parameters and the output parameters are all expressed by the level-values in fuzzy field. Therefore, the output parameters used for control can be obtained for the fuzzy control table according to the detected actual input parameters, by which the EDM combined with ultrasonic vibration is improved and the machining efficiency is increased. In addition, a stimulation program is designed by means of Microsoft Visual Basic
文摘In this study, a newly developed titanium superalloy, i.e., the Ti-5553 alloy has used for hot machining. This material replaced Ti-grade-5 alloy in the application of aerospace, automobile, and biomedical sector. However, similar to Ti-grade-5 alloy, the Ti-5553 alloy has a low thermal conductivity which makes it difficult-to-cut material categories hence, high tool wear, cutting force and bad surface finish. Hot machining of Ti-5553 has been studied at different machining condition (room and hot) using Deform-2D finite element analysis. The result from the simulation test was compared with the experimental value and reduction of cutting and thrust forces was observed. The experiment was carried out with the same input parameters as simulation, and good coherence between them observed. Additionally, cutting zone temperature, effective stress, etc. for both room and elevated the temperature are also discussed.
基金Project supported by the Second Stage of Brain Korea 21 Projects
文摘An impeller is difficult to machine because of severe collision due to the complex shape,overlapping and twisted shape of the impeller blades.So,most computer aided manufacturing(CAM)software companies have developed CAM module for manufacturing impeller according to their CAM software.But these dedicated modules are difficult to use for inexperienced users.The purpose of this work is to develop a tool-path generation module for impellers.For this purpose,it is based on Visual Basic language and used CATIA graphical environment.The result of simulation for generated tool-path by the module is satisfactory.And it has slow processing speed compared to other commercial modules,but it is easy to use.
文摘This paper describes a new method of surface modification by Electrical Discharge Machining (EDM). By using ordinary EDM machine tool and kerosene fluid, a hard ceramic layer can be created on the workpiece surface with Ti or other compressed powder electrode in a certain condition. This new revolutionary method is called Electrical Discharge Coating (EDC). The process of EDC begins with electrode wear during EDM,then a kind of hard carbide is created through the thermal and chemical reaction between the worn electrode material and the carbon particle decomposed from kerosene fluid under high temperature. The carbide is piled up on a workpiece quickly and becomes a hard layer of ceramic about 20 μm in several minutes. This paper studies the principle and process of EDC systemically by using Ti powder green compact electrode. In order to obtain a layer of compact ceramic film, it is very important to select proper electric pulse parameters, such as pulse width, pulse interval, peak current. Meantime, the electrode materials and its forming mode will effect the machining surface quality greatly. This paper presents a series of experiment results to study the EDC process by adopt different technology parameters. Experiments and analyses show that a compact TiC ceramic layer can be created on the surface of metal workpiece. The hardness of ceramic layer is more 3 times higher than the base body, and the hardness changes gradiently from surface to base body. The method will have a great future because many materials can be easily added to the electrode and then be coated on the workpiece surface. Gearing the parameters ceramic can be created with different thickness. The switch between deposition and removal process is carried out easily by changing the polarity, thus the gear to the thickness and shape of the composite ceramic layer is carried out easily. This kind of composite ceramic layer will be used to deal with the surface of the cutting tools or molds possibly, in order to lengthen their life. It also can be found wide application in the fields of surface repairing and strengthening of the ship or aircraft.
基金Projects(51206011,U1937201)supported by the National Natural Science Foundation of ChinaProject(20200301040RQ)supported by the Science and Technology Development Program of Jilin Province,China+1 种基金Project(JJKH20190541KJ)supported by the Education Department of Jilin Province,ChinaProject(18DY017)supported by Changchun Science and Technology Program of Changchun City,China。
文摘The investigation was carried out on the technical problems of finishing the inner surface of elbow parts and the action mechanism of particles in elbow precision machining by abrasive flow.This work was analyzed and researched by combining theory,numerical and experimental methods.The direct simulation Monte Carlo(DSMC)method and the finite element analysis method were combined to reveal the random collision of particles during the precision machining of abrasive flow.Under different inlet velocity,volume fraction and abrasive particle size,the dynamic pressure and turbulence flow energy of abrasive flow in elbow were analyzed,and the machining mechanism of particles on the wall and the influence of different machining parameters on the precision machining quality of abrasive flow were obtained.The test results show the order of the influence of different parameters on the quality of abrasive flow precision machining and establish the optimal process parameters.The results of the surface morphology before and after the precision machining of the inner surface of the elbow are discussed,and the surface roughness Ra value is reduced from 1.125μm to 0.295μm after the precision machining of the abrasive flow.The application of DSMC method provides special insights for the development of abrasive flow technology.
基金Project(51275116)supported by the National Natural Science Foundation of ChinaProject(2012ZE77010)supported by the Aero Science Foundation of ChinaProject(LBH-Q11090)supported by the Postdoctoral Science Research Development Foundation of Heilongjiang Province,China
文摘The electric double layer with the transmission of particles was presented based on the principle of electrochemistry.In accordance with this theory,the cavitation catalysis removal mechanism of ultrasonic-pulse electrochemical compound machining(UPECM) based on particles was proposed.The removal mechanism was a particular focus and was thus validated by experiments.The principles and experiments of UPECM were introduced,and the removal model of the UPECM based on the principles of UPECM was established.Furthermore,the effects of the material removal rate for the main processing parameters,including the particles size,the ultrasonic vibration amplitude,the pulse voltage and the minimum machining gap between the tool and the workpiece,were also studied through UPECM.The results show that the particles promote ultrasonic-pulse electrochemical compound machining and thus act as the catalyzer of UPECM.The results also indicate that the processing speed,machining accuracy and surface quality can be improved under UPECM compound machining.
基金Project(2011-0017407)supported by the National Research Foundation of Korea(NRF)grant funded by the Korea government(MEST)
文摘For laser assisted machining,shape of preheating laser heat source is changed irregularly because of complexity of material shape.So,the preheating temperature should be controlled by adjusting the feed rate or the laser power.Thermal analyses of the laser assisted machining process for inclination planes were performed.By analyzing the obtained temperature profile,a proper feed rate control method was proposed according to the inclination angles.In addition,the temperature distribution of the cross section after feed rate control was predicted.The correlation equation between inclination angles and adjusted proper feed rate was proposed.The results of this analysis can be used to predict the preheating effect on workpiece and can be applied as a preheating temperature control method in laser assisted machining processes.
文摘Wire electric discharge machining(WEDM)process is used for precision manufacturing.The accuracy of machining is function of various parameters like current,voltage,wire speed,gap between wire and work piece,wire oscillation,work material,wire material,etc.Once the process parameters are selected,it is important that the wire vibrations are less to obtain a good surface finish.Due to the importance of wire vibration in obtaining the surface finish,it is necessary to study the wire vibration.This paper discusses different models of wire vibration presented in the literature and simulates a closed form solution of wire vibration using MATLAB.The transverse vibration of wire is analysed as forced vibration of moving wire with excitation due to the sparks during machining.The resulting partial differential equation is solved by using finite difference method and vibration is also simulated in the finite element package‘ANSYS’.The wire behaviour is investigated under different operating conditions and results of the two methods are
基金Work supported by the Second Stage of Brain Korea 21 ProjectsProject(RTI04-01-03) supported by the Regional Technology Innovation Program of the Ministry of Knowledge Economy (MKE) of Korea
文摘During five-axis machining of impeller, the excessive local interference avoidance leads to inconsistency of cutter posture, low quality of machined surface and increase of processing time. Therefore, in order to improve the efficiency of five-axis machining of impellers, it is necessary to minimize the cutter posture changes and create a continuous tool path while avoiding interference. By using an MC-space algorithm for interference avoidance, an MB-spline algorithm for continuous control was intended to create a five-axis machining tool path with excellent surface quality and economic feasibility. A five-axis cutting experiment was performed to verify the effectiveness of the continuity control. The result shows that the surface shape with continuous method is greatly improved, and the surface roughness is generally favorable. Consequently, the effectiveness of the suggested method is verified by identifying the improvement of efficiency of five-axis machining of an impeller in aspects of surface quality and machining time.
文摘Ultrasonic machining (USM) is considered as an effective method for machining hard and brittle materials such as glass, engineering ceramics, semiconductors, diamonds, metal composites and so on. However, the low material removal rate due to using abrasive slurry limits further application of USM. Rotary ultrasonic machining (rotary USM) superimposes rotational movement on the tool head that vibrates at ultrasonic frequency (20 kHz) simultaneously. The tool is made of mild steel coated or bonded with diamond abrasive. Therefore, abrasive slurry is abandoned and coolant is used to carry debris out of working area. Compared with USM, rotary USM can obtain much higher material removal rate, deep holes, and fine precision, which leads to its further application. Combined with CNC technology, rotary USM can be used to conduct contour machining of hard and brittle materials. In this paper, the movement of abrasive particles in tool tip of rotary ultrasonic machining is analyzed. The impacting and grinding of abrasive in tool tip to machined surface are considered as main factors to material removal rate. The process of crack forming and growing in one loading and unloading cycle can be described as following stages: a) When abrasive particle acts the pressure on work-piece, the macro cracks in periphery of contact area are exerted increasing tensile stress. b) As the tensile stress increase to the critical of material tension, the one of cracks in periphery of contact area begins to propagate around contact area and develop beneath the surface to certain depth. c) Indentation area varies with increasing of load, the circle crack around contact area steadily or dynamical propagates towards inside of work-piece. d) As tensile stress in crack increases to critical of crack steady failure, circle crack suddenly becomes conic crack. e) Further increase load, the crack continues to grow while contact area is surrounded by conic cracks. f) During unloading, conic crack begins to close, some of cracks continue their extension towards the surface and forms a circle groove. The mathematical model for material removal rate shows that the factors affecting on material removal rate are static load, grid and concentration of abrasive, mechanical properties of machined materials, rotational speed of tool and feed speed of work-piece.
文摘As the cutting speed goes higher, the mechanism of chip deformation will be changed significantly, i.e., continuous chip in low cutting speed will shift to serrated chip with shear localization. For the shear localized chip, the parameters used to assess the chip deformation for continuous chip, such as shorten coefficient ξ, shear angle φ and shear strain ε, can not describe the chip deformation correctly or comprehensively. This paper deals with the assessment of chip deformation of shear localization. There are two deformation regions in shear localized chip, one is the chip segment body with relative smaller plastic deformation, another one is the boundary between segments with shear localization, so called shear band. Considering the two distinct deformation regions, two parameters are used to define their deformation respectively. According to the analysis of chip formation process, the equations have been deduced to calculate the shear strains of shear band ε, shear strain of chip segment ε 1 and shear rate so that the shear localized chip deformation can be assessed correctly and comprehensively. By use of this assessment, the chip deformation in machining selenium treated stainless steel (STSS) and common stainless steel at various cutting conditions is investigated. The experiment results obtained by the machining of stainless steel prove that: (1) the shear strain and strain rate increase with the increasing of cutting speed; (2) the shear strain in shear band can be over 10 when cutting speed exceeding 200 m/min for both types of stainless steel, and it is much higher than the strain of chip segment. The difference will be enlarged as the cutting speed increasing; (3) As the comparison, the shear strain for the STSS is a little lower than that for JIS304; (4) The stain rate is extremely high (= 2.5×10 5 1/s ). In range of cutting speed less than 180 m/min, the strain rate for STSS is lower than that for JIS304. However, when the cutting speed is higher than 180 m/min, the strain rate for STSS is higher than that for JIS304.
基金Project(60772089) supported by the National Natural Science Foundation of ChinaProject(20080440939) supported by the China Postdoctoral Science Foundation
文摘In the process of numerical control machining simulation,the workpiece surface is usually described with the uniform triangular mesh model.To alleviate the contradiction between the simulation speed and accuracy in this model,two improved methods,i.e.,the local refinement triangular mesh modeling method and the adaptive triangular mesh modeling method were presented.The simulation results show that when the final shape of the workpiece is known and its mathematic representation is simple,the local refinement triangular mesh modeling method is preferred;when the final shape of the workpiece is unknown and its mathematic description is complicated,the adaptive triangular mesh modeling method is more suitable.The experimental results show that both methods are more targeted and practical and can meet the requirements of real-time and precision in simulation.
文摘This work demonstrates the viability of the powder-mixed micro-electrochemical discharge machining(PMECDM) process to fabricate micro-holes on C103 niobium-based alloy for high temperature applications.Three processes are involved simultaneously i.e.spark erosion,chemical etching,and abrasive grinding for removal of material while the classical electrochemical discharge machining process involves double actions i.e.spark erosion,and chemical etching.The powder-mixed electrolyte process resulted in rapid material removal along with a better surface finish as compared to the classical microelectrochemical discharge machining(MECDM).Further,the results are optimized through a multiobjective optimization approach and study of the surface topography of the hole wall surface obtained at optimized parameters.In the selected range of experimental parameters,PMECDM shows a higher material removal rate(MRR) and lower surface roughness(R_(a))(MRR:2.8 mg/min and R_(a) of 0.61 μm) as compared to the MECDM process(MRR:2.01 mg/min and corresponding Raof 1.11 μm).A detailed analysis of the results is presented in this paper.
基金Project(2012-0005688) supported by the National Research Foundation of Korea (NRF) Grant funded by the Korea Government (MEST)
文摘Laser-assisted machining has been considered as a new alternative machining method of difficult-to-cut materials. A laser module with one-axis manipulator is developed to focus on preheating laser beam effectively. First of all, the thermal characteristic analysis was performed to verify the importance of laser module location. Laser module should be moved within 1 mm. Analysis conditions of three positions in driving range of the one-axis manipulator are selected. And a C coupling is used as a connection device for spindle and laser module. An initial model has one C coupling, and the number of C coupling has been increased from 1 to 2 in an improved model. And the analysis is carried out again for the one-axis manipulator. The results of the static analysis, the maximum displacement and the maximum stress are decreased by 22% and 11%, respectively, for the improved model when the laser module is located at farthest away from the spindle unit. As a result of the modal analysis, the first natural frequency mode is increased by 13%, 18% and 12% at these positions of the improved model, respectively. The harmonic analysis of the improved model was performed by analyzing the results of the modal analysis. The maximum deformation was 0.33 mm in driving unit at 222 Hz. And the maximum compliance of the ISO axis direction was 0.23 mm/N. Finally, the one-axis manipulator has been fabricated successfully using the analysis result.
