The Microcystis aeruginosa(MA) was immobilized on sodium alginate and used as biosorbent for removal of Cd(Ⅱ) ions from aqueous solution.The biosorption process is pH dependent,and the optimum biosorption was observe...The Microcystis aeruginosa(MA) was immobilized on sodium alginate and used as biosorbent for removal of Cd(Ⅱ) ions from aqueous solution.The biosorption process is pH dependent,and the optimum biosorption was observed at pH 6.0 with the biosorption capacity of 98.38 mg/g.Among Langmuir,Freundlich and Temkin isotherm models,the Freundlich and the Temkin isotherm fit well with the experimental data.Cd(Ⅱ) ions biosorption follows the pseudo-second-order kinetic model.The rate controlling mechanism study reveals that film diffusion is the rate-limiting step and intraparticle diffusion is also involved in biosorption.Thermodynamic parameters,such as Gibbs free energy(ΔG°),the enthalpy(ΔH°) and entropy(ΔS°) were calculated,and revealed that the biosorption process is spontaneous,exothermic and random.Furthermore,the immobilized MA can be regenerated using 0.1 mol/L HCl solutions.展开更多
This work aims to investigate the efficiency of Fariman sepiolite from Iran as an adsorbent to remove Cd from aqueous solutions. The effects of different experimental factors such as the initial Cd concentration, cont...This work aims to investigate the efficiency of Fariman sepiolite from Iran as an adsorbent to remove Cd from aqueous solutions. The effects of different experimental factors such as the initial Cd concentration, contact time and the sorbent dose were investigated through a series of batch adsorption experiments. The results show that the adsorption capacity of sepiolite for Cd increases with the contact time, the initial concentration of Cd solutions and the sorbent dose. Sorption of Cd by Fariman sepiolite is rapid within the first hour of the experiment and then slowly increases until a pseudo equilibrium is approached at 8 h. The results also show that the time-dependent Cd sorption data are better described with pseudo second-order （7〉0.999） than that of pseudo first-order （r2〉0.971） kinetic model. Equilibrium isotherm studies show that the experimental data are better correlated by the Freundlich adsorption isotherm （7〉0.995） than the Langmuir （P〉0.825）. It is suggested that both adsorption and cation exchange reactions are responsible for the sorption of Cd by the sepiolite, and the mineral has a very good potential to remove Cd from aqueous solutions.展开更多
Cold-rolling was conducted on AZ31 magnesium alloy with fine and coarse grains to produce plates with high density of shear bands and{101^(-)1}twins,respectively.Then,these two kinds of plates are subjected to isother...Cold-rolling was conducted on AZ31 magnesium alloy with fine and coarse grains to produce plates with high density of shear bands and{101^(-)1}twins,respectively.Then,these two kinds of plates are subjected to isothermal annealing to reveal the effect of shear bands and{101^(-)1}twins on recrystallization behavior.During annealing,static recrystallization occurs firstly in shear band zones and{101^(-)1}twin zones,which has different effect on texture and mechanical properties.With the increase of annealing temperature,strong basal texture remains in annealed SG-17%while the basal texture is weakened gradually in annealed LG-15%.Recrystallized grains from twin zones have a random orientation which is responsible for the weakened basal texture in annealed LG-15%.In addition,microhardness decreases gradually with the prolonged annealing time due to static recrystallization.LG-15%has a lower recrystallization activation energy because{101^(-)1}twins are in favor of the nucleation and growth of recrystallized grains.After 500℃annealing,the yield strength decreases significantly with a significant improvement in failure strain.The annealed LG-15%has a much higher compressive strain than the annealed SG-17%due to texture weakening effect.展开更多
Roasting bastnaesite concentrates is a crucial process in extracting rare earths.This study explored an efficient suspension roasting technology and investigated the bastnaesite pyrolysis and cerium(Ce)oxidation.Relev...Roasting bastnaesite concentrates is a crucial process in extracting rare earths.This study explored an efficient suspension roasting technology and investigated the bastnaesite pyrolysis and cerium(Ce)oxidation.Relevant analytical tests were applied to evaluate the phase and surface property variations of bastnaesite,and isothermal kinetic analysis of bastnaesite pyrolysis and Ce oxidation was performed.The results revealed that bastnaesite decomposed rapidly and accompanied by Ce oxidation,and the gas-solid products were identified as CO_(2),Ce_(7)O_(12),La_(2)O_(3),CeF_(3) and LaF_(3),with Ce oxidation restricted by bastnaesite pyrolysis.As roasting time prolonged,cracks and pores appeared on bastnaesite surface;the BET specific surface and pore diameter increased.In later roasting period,the pore diameter continued to increase but the specific surface decreased,assigned to particle fusion agglomeration and pore consolidation.Additionally,the surface C content reduced and Ce(Ⅳ)content increased gradually as roasting progressed.The reaction kinetics all followed Avrami-Erofeev equations,the reaction orders of bastnaesite pyrolysis and Ce oxidation decreased with decreasing reaction temperature.The calculated activation energies at lower temperatures were higher than those calculated at higher temperatures.This study analyzed the bastnaesite reaction mechanism to supply a reference for the application of suspension roasting technology in bastnaesite smelting.展开更多
In order to analyze the influences of storage aging on the safety of typical elemental explosives,the aged cyclotrimethylene trinitramine(RDX)and cyclotetramethylene tetranitramine(HMX)were prepared by isothermal agin...In order to analyze the influences of storage aging on the safety of typical elemental explosives,the aged cyclotrimethylene trinitramine(RDX)and cyclotetramethylene tetranitramine(HMX)were prepared by isothermal aging tests.The reaction thresholds of aged RDX and HMX under any ignition probability were studied by Langlie-Optimal D method.The thermal decomposition characteristics of RDX and HMX after aging were analyzed by DSC and ARC.Experimental results showed that compared with unaged RDX and HMX,on the one hand,the critical impact energy and critical friction of RDX and HMX aged for 14,28,and 56 days are significantly reduced at an explosion probability of 50%,0.01%,and 0.0001%,respectively.With the increase of aging time,the mechanical sensitivity of RDX and HMX increases obviously.On the other hand,the initial decomposition temperature of RDX and HMX after 56 days of aging decreases,the decomposition heat decreases,the activation energy increases,and the reaction difficulty increases.展开更多
The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the...The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the adsorption process of W obeys the Freundlich model very well whereas the exchange process with Mo approximately follows the Henry model.The kinetic experiments show that the intraparticle diffusion process was the rate-determining step for W sorption on the resin,and the corresponding activation energy is calculated to be 21.976 k J/mol.展开更多
Brine,which is used to produce high-purity magnesia,was purified by XSC-700 to remove boron.Boron adsorption capacity of XSC-700 was investigated by varying the initial boron concentration,temperature,resin/brine rati...Brine,which is used to produce high-purity magnesia,was purified by XSC-700 to remove boron.Boron adsorption capacity of XSC-700 was investigated by varying the initial boron concentration,temperature,resin/brine ratio and stirring speed,while keeping the diameter at constant.The results show that boron adsorption capacity increases with increasing boron concentration,temperature,and decreases with increasing resin/brine ratio.And the stirring speed could slightly affect the boron adsorption capacity.The adsorption kinetics obeys the pseudo-second-order model.Equilibrium data were both examined by Freundlich and Langmuir isotherm equations and it can be well represented by the Freundlich isotherm equation.展开更多
Endotoxins(also known as lipopolysaccharides(LPS)) are undesirable by-products of recombinant proteins,purified from Escherichia coli.LPS can be considered stable under a wide range of temperature and pH,making their ...Endotoxins(also known as lipopolysaccharides(LPS)) are undesirable by-products of recombinant proteins,purified from Escherichia coli.LPS can be considered stable under a wide range of temperature and pH,making their removal one of the most difficult tasks in downstream processes during protein purification.The inherent toxicity of LPS makes their removal an important step for the application of these proteins in several biological assays and for a safe parenteral administration.Immobilized metal affinity chromatography(IMAC) enables the affinity interactions between the metal ions(immobilized on the support through the chelating compound) and the target molecules,thus enabling high-efficiency separation of the target molecules from other components present in a mixture.Affinity chromatography is applied with Ca2+-iminodiacetic acid(IDA) to remove most of the LPS contaminants from the end product(more than90%).In this study,the adsorption of LPS on an IDA-Ca2+ was investigated.The adsorption Freundlich isotherm of LPS-IDA-Ca2+ provides a theoretical basis for LPS removal.It was found that LPS is bound mainly by interactions between the phosphate group in LPS and Ca2+ ligands on the beads.The factors such as pH(4.0 or 5.5) and ionic strength(1.0 mol/L) are essential to obtain effective removal of LPS for contaminant levels between endotoxin' concentration values less than100 EU/mL and 100 000 EU/mL.This new protocol represents a substantial advantage in time,effort,and production costs.展开更多
To establish a theoretical foundation for simultaneous removal of multi-heavy metals,the adsorption of Cu（Ⅱ） and Pb（Ⅱ） ions from their single and binary systems by Ca-alginate immobilized activated carbon and Sa...To establish a theoretical foundation for simultaneous removal of multi-heavy metals,the adsorption of Cu（Ⅱ） and Pb（Ⅱ） ions from their single and binary systems by Ca-alginate immobilized activated carbon and Saccharomyces cerevisiae （CAS） was investigated.The CAS beads were characterized by Scanning electron microscope （SEM） and Fourier transformed infrared spectroscopy （FTTR）.The effect of initial pH,adsorbent dosage,contact time and initial metal ions concentration on the adsorption process was systematically investigated.The experimental maximum contents of Cu（Ⅱ） and Pb（Ⅱ） uptake capacity were determined as 64.90 and 166.31 mg/g,respectively.The pseudo-second-order rate equation and Langmuir isotherm model could explain respectively the kinetic and isotherm experimental data of Cu（Ⅱ） and Pb（Ⅱ） ions in single-component systems with much satisfaction.The experimental adsorption data of Cu（Ⅱ） and Pb（Ⅱ） ions in binary system were best described by the extended Freundlich isotherm and the extended Langmuir isotherm,respectively.The removal of Cu（lⅡ） ions was more significantly influenced by the presence of the coexistent Pb（Ⅱ） species,while the Pb（Ⅱ） removal was affected slightly by varying the initial concentration of Cu（Ⅱ）.The CAS was successfully regenerated using 1 mol/L HNO3 solution.展开更多
In order to amend the superficial performance of palygorskite and improve its application, the natural palygorskite(NP) was treated in the dipping and ionic exchanging experiments using 6mol/L hydrochloric acid treatm...In order to amend the superficial performance of palygorskite and improve its application, the natural palygorskite(NP) was treated in the dipping and ionic exchanging experiments using 6mol/L hydrochloric acid treatment. The performance and pore structure of the treated palygorskite(TP) were investigated by means of microscope analyses, FT-IR, XRF, BET-SSA and full hole distribution analytical techniques. The results show that the hydrochloric acid treatment can make the gracile and aggregating compact crystal bundles inside palygorskite clay broken and dispersed, the roughness of microcrystalline surface increases, which not only can dissolve or remove dolomite but vary the superficial performance of palygorskite to some degree. The specific surface area and pore volume increase a lot, while the mean pore size decreases. The pore structure of TP changes remarkably compared with that of NP after 6mol/L hydrochloric acid treatment, and the relevant physicochemical performance can be improved.展开更多
A batch experiment was conducted to investigate the adsorption of an acid dye(Acid Orange 51) and a basic dye(Safranine) from aqueous solutions by the sludge-based activated carbon(SBAC). The results show that the ads...A batch experiment was conducted to investigate the adsorption of an acid dye(Acid Orange 51) and a basic dye(Safranine) from aqueous solutions by the sludge-based activated carbon(SBAC). The results show that the adsorption of Acid Orange 51 decreases at high p H values, whereas the uptake of Safranine is higher in neutral and alkaline solutions than that in acidic conditions. The adsorption time needed for Safranine to reach equilibrium is shorter than that for Acid Orange 51. The uptakes of the dyes both increase with temperature increasing, indicating that the adsorption process of the dyes onto SBAC is endothermic. The equilibrium data of the dyes are both best represented by the Redlich-Peterson model. At 25 °C, the maximum adsorption capacities of SBAC for Acid Orange 51 and Safranine are 248.70 mg/g and 525.84 mg/g, respectively. The Elovich model is found to best describe the adsorption process of both dyes, indicating that the rate-limiting step involves the chemisorption. It can be concluded that SBAC is a promising material for the removal of Acid Orange 51 and Safranine from aqueous solutions.展开更多
The adsorption capacity of Pb(Ⅱ) on litchi pericarps was investigated as a function of temperature,pH,and adsorbent dose using batch experiments.The experimental data obtained were evaluated using adsorption equilibr...The adsorption capacity of Pb(Ⅱ) on litchi pericarps was investigated as a function of temperature,pH,and adsorbent dose using batch experiments.The experimental data obtained were evaluated using adsorption equilibrium isotherms and a kinetic model.Additionally,the removal of Pb(Ⅱ) in leachate of litchi pericarps was also evaluated.The results show that litchi pericarps exhibit a high adsorption capacity to Pb(Ⅱ),with the maximum removal efficiency occurring at a temperature of 25 ℃,a pH of 6.0-7.0 and an adsorbent dosage of 10 g/L.Langmuir and Freundlich isotherms and the pseudo-second-order kinetic model can all fit the equilibrium adsorption satisfactorily,with correlation coefficients(R^2) of 0.9935,0.9918 and 1.0,respectively.An average removal efficiency of 66.65% is found for Pb(Ⅱ) in leachate of litchi pericarps.展开更多
Different mesoporous activated carbons were prepared by both chemical and physical activation processes and were examined for methane uptake in the presence of water.Methane isotherms were obtained at wet condition by...Different mesoporous activated carbons were prepared by both chemical and physical activation processes and were examined for methane uptake in the presence of water.Methane isotherms were obtained at wet condition by wetting samples with water at mass ratio of water/carbon(R) close to 1.0.To compare,the amount of methane storage were also measured at dry situation.The maximum amount of methane stored was attained as 237 V/V at R=1.0 by hydrate formation at the methane critical pressure.In the next step,mass ratios of water/carbon were changed to investigate various amount of water for methane storage enhancement.Two other values of mass ratio of water/carbon(R=0.8 and 1.4) were selected and methane isotherms were obtained at the same conditions.Maximum values of 210 and 248 V/V were reached for methane storage,respectively.It was also observed that,in the pressure range lower than hydrate pressure,by increasing water ratio the hydrate formation pressure was decreased and methane uptake was much less than that of dry condition due to pore filling by water.展开更多
The microstructure and Gd-rich phase evolution of as-cast AZ31-xGd(x=0,1.5 wt.%,2.0 wt.%and 2.5 wt.%)magnesium alloys during semi-solid isothermal heat treatment were investigated deeply in the present work.Results sh...The microstructure and Gd-rich phase evolution of as-cast AZ31-xGd(x=0,1.5 wt.%,2.0 wt.%and 2.5 wt.%)magnesium alloys during semi-solid isothermal heat treatment were investigated deeply in the present work.Results showed that the lamellar(Mg,Al)3Gd phases transformed into the particle-like Al2Gd phases in AZ31 magnesium alloys with Gd addition during semi-solid isothermal heat treatment,leading to yielding more sphericalα-Mg grains.When Gd content is 2.0 wt.%,the size of semi-solid spherical grains reaches the minimum.The main mechanism of grain refinement lies in the remelting of dendritic branches as well as the auxiliary effect of a small number of Al2Gd particles as grain refining inoculants.Meanwhile,Al2Gd particles enriched at the solid-liquid interfaces can remarkably retard the growth rate ofα-Mg grains.A reduction of deformation resistance has been successfully achieved in AZ31-2.0Gd magnesium alloy after semi-solid isothermal heat treatment,which shows a moderate compressive deformation resistance(230 MPa),comparing to the as-cast AZ31 magnesium alloy(280 MPa)and semi-solid AZ31 magnesium alloy(209 MPa).展开更多
The potential of di-(m-Formylphenol)-1,2-cyclohexandiimine as an environmentally friendly corrosion inhibitor for steel was investigated in 1 mol/L HCl using potentiodynamic polarization, electrochemical impedance spe...The potential of di-(m-Formylphenol)-1,2-cyclohexandiimine as an environmentally friendly corrosion inhibitor for steel was investigated in 1 mol/L HCl using potentiodynamic polarization, electrochemical impedance spectroscopy and chronoamperometry measurements. All electrochemical measurements suggest that this compound is an excellent corrosion inhibitor for mild steel and the inhibition efficiency increases with the increase in inhibitor concentration. The effect of temperature on the corrosion behavior of mild steel with the addition of the Schiff base was studied in the temperature range from 25 °C to 65 °C. It is found that the adsorption of this inhibitor follows the Langmuir adsorption isotherms. The value of activation energy and the thermodynamic parameters such as ΔHads, ΔSads, Kads and ΔGads were calculated by the corrosion currents at different temperatures using the adsorption isotherm. The morphology of mild steel surface in the absence and presence of inhibitor was examined by scanning electron microscopy(SEM) images.展开更多
The isotherm,mechanism and kinetics of carbon tetrachloride(CT) adsorption by polyacrylonitrile-based activated carbon fiber(PAN-ACF) were investigated in batch reactors and a continuous flow reactor,and the regenerat...The isotherm,mechanism and kinetics of carbon tetrachloride(CT) adsorption by polyacrylonitrile-based activated carbon fiber(PAN-ACF) were investigated in batch reactors and a continuous flow reactor,and the regeneration of PAN-ACF was also studied.Freundlich and Dubinin-Radushkevich(D-R) adsorption equations can well describe the adsorption isotherm.CT is mainly adsorbed on the exterior surface of PAN-ACF with low boundary layer effect and rate-controlling step of intra-particle diffusion.The adsorption dynamics in the batch reactor well fits with the pseudo-first-order model,and the breakthrough curves in the continuous flow reactor can be well described by the Yoon-Nelson model.The ACF can be recycled through thermal regeneration,whereas the adsorption capacity decreases from 7.87 to 4.98 mg/g after the fourth regeneration.78%-94%of CT can be removed from the wastewater of a fluorine chemical plant on a pilot scale,which confirms the efficacy of ACF under industrial conditions.The results indicate that PAN-ACF is applicable to CT removal from wastewater.展开更多
The inhibition ability of 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol （APTT）, ethylenediaminetetra-acetic acid （EDTA） and thiourea （TU） for mild steel corrosion in 1.0 moFL HC1 solution at 30 ℃ was investigated...The inhibition ability of 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol （APTT）, ethylenediaminetetra-acetic acid （EDTA） and thiourea （TU） for mild steel corrosion in 1.0 moFL HC1 solution at 30 ℃ was investigated. Tafel polarization and electrochemical impedance spectroscopy （EIS） were used to investigate the influence of these organic compounds as corrosion inhibitors of mild steel in 1.0 mol/L HC1 solution at 30 ℃. The inhibition mechanism was discussed in terms of Langrnuir isotherm model. Results obtained from Tafel polarization and impedance measurements are in a good agreement. The inhibition efficiency increases with the increase of the inhibitor concentration. The adsorption of the inhibitors on the mild steel surface follows Langmuir adsorption isotherm and the free energy of adsorption AGads indicates that the adsorption of APTT, EDTA, and TU molecules is a spontaneous process and a typical chemisorption.展开更多
A low-cost adsorbent modified kaolin clay(MKC) was synthesized and utilized for Cr(VI) removal from aqueous solution. Adsorption experiments were carried out as a function of adsorbent dosage, solution pH, Cr(VI) mass...A low-cost adsorbent modified kaolin clay(MKC) was synthesized and utilized for Cr(VI) removal from aqueous solution. Adsorption experiments were carried out as a function of adsorbent dosage, solution pH, Cr(VI) mass concentration, contact time, electrolyte, and temperature. It is found that the adsorption efficiency is high within a wide pH range of 2.5-11.5, and equilibrium is achieved within 180 min. Increases in temperature and electrolyte concentration decrease the adsorption. The adsorption follows the pseudo-second-order kinetic model. The Langmuir isotherm shows better fit than Freundlich isotherm. The maximum uptake capacities calculated from the Langmuir model are 15.82, 15.55 and 15.22 mg/g at 298, 308 and 318 K, respectively. Thermodynamic parameters reveals the spontaneous and exothermic nature of the adsorption. The FTIR study indicates that hydroxyl groups, NH4+ ions and NO3- ions on MKC surface play a key role in Cr(VI) adsorption. The Cr(VI) desorbability of 86.53% is achieved at a Na2CO3 solution. The results show that MKC is suitable as a low-cost adsorbent for Cr(VI) removal which has higher adsorption capacity and faster adsorption rate at pH close to that where pollutants are usually found in the environment.展开更多
The ablation properties of C/C composites with four different needled preforms prepared by isothermal chemical vapor infiltration （ICVI）, which are super-thin mat lay-up, 0°/90° weftless fabric lay-up, 0&#...The ablation properties of C/C composites with four different needled preforms prepared by isothermal chemical vapor infiltration （ICVI）, which are super-thin mat lay-up, 0°/90° weftless fabric lay-up, 0°/45° weftless fabric lay-up and 0°/45° twill fabric lay-up, were quantitatively evaluated by performing the ablation tests with an engine torch. And their ablation discrepancies were analyzed according to the surface characteristic, porosity and thermal diffusivity. The results show that the 0°/45° weftless composite has a fiat eroded surface with no obvious macroscopic pits. Its thickness and mass erosion rates are decreased by about 46.8% and 34.8%, 25.0% and 27.5%, and 17.5% and 19.4% compared with those of the mat, the 0°/90° weftless and the 0°/45° twill composites, respectively. The ablation properties are mainly controlled by the thermo-chemical effect （oxidation）, and a little by the thermo-mechanical effect （mechanical denudation）. The needling fiber bundles play an important role in accelerating the ablation process and resulting in the heterogeneous ablation.展开更多
基金Project(41271332) supported by the National Natural Science Foundation of ChinaProject(11JJ2031) supported by the Natural Science Foundation of Hunan Province,China+1 种基金Project(2012SK2021) supported by the Science and Technology Planning Program of Hunan Province,ChinaProject(CX2012B138) supported by the Hunan Provincial Innovation Foundation for Postgraduate,China
文摘The Microcystis aeruginosa(MA) was immobilized on sodium alginate and used as biosorbent for removal of Cd(Ⅱ) ions from aqueous solution.The biosorption process is pH dependent,and the optimum biosorption was observed at pH 6.0 with the biosorption capacity of 98.38 mg/g.Among Langmuir,Freundlich and Temkin isotherm models,the Freundlich and the Temkin isotherm fit well with the experimental data.Cd(Ⅱ) ions biosorption follows the pseudo-second-order kinetic model.The rate controlling mechanism study reveals that film diffusion is the rate-limiting step and intraparticle diffusion is also involved in biosorption.Thermodynamic parameters,such as Gibbs free energy(ΔG°),the enthalpy(ΔH°) and entropy(ΔS°) were calculated,and revealed that the biosorption process is spontaneous,exothermic and random.Furthermore,the immobilized MA can be regenerated using 0.1 mol/L HCl solutions.
基金Shahid Chamran University of Ahvaz and Isfahan University of Technology for the financial supports they provided for this study
文摘This work aims to investigate the efficiency of Fariman sepiolite from Iran as an adsorbent to remove Cd from aqueous solutions. The effects of different experimental factors such as the initial Cd concentration, contact time and the sorbent dose were investigated through a series of batch adsorption experiments. The results show that the adsorption capacity of sepiolite for Cd increases with the contact time, the initial concentration of Cd solutions and the sorbent dose. Sorption of Cd by Fariman sepiolite is rapid within the first hour of the experiment and then slowly increases until a pseudo equilibrium is approached at 8 h. The results also show that the time-dependent Cd sorption data are better described with pseudo second-order （7〉0.999） than that of pseudo first-order （r2〉0.971） kinetic model. Equilibrium isotherm studies show that the experimental data are better correlated by the Freundlich adsorption isotherm （7〉0.995） than the Langmuir （P〉0.825）. It is suggested that both adsorption and cation exchange reactions are responsible for the sorption of Cd by the sepiolite, and the mineral has a very good potential to remove Cd from aqueous solutions.
基金Project(52405369) supported by National Natural Science Foundation of ChinaProject(BK20210891) supported by the Natural Science Foundation of Jiangsu Province,ChinaProject(BX2022030) supported by the Special Project of Introducing Foreign Talents of Jiangsu Province,China。
文摘Cold-rolling was conducted on AZ31 magnesium alloy with fine and coarse grains to produce plates with high density of shear bands and{101^(-)1}twins,respectively.Then,these two kinds of plates are subjected to isothermal annealing to reveal the effect of shear bands and{101^(-)1}twins on recrystallization behavior.During annealing,static recrystallization occurs firstly in shear band zones and{101^(-)1}twin zones,which has different effect on texture and mechanical properties.With the increase of annealing temperature,strong basal texture remains in annealed SG-17%while the basal texture is weakened gradually in annealed LG-15%.Recrystallized grains from twin zones have a random orientation which is responsible for the weakened basal texture in annealed LG-15%.In addition,microhardness decreases gradually with the prolonged annealing time due to static recrystallization.LG-15%has a lower recrystallization activation energy because{101^(-)1}twins are in favor of the nucleation and growth of recrystallized grains.After 500℃annealing,the yield strength decreases significantly with a significant improvement in failure strain.The annealed LG-15%has a much higher compressive strain than the annealed SG-17%due to texture weakening effect.
基金Projects(2022YFC2905800,2021YFC2901000)supported by the National Key R&D Program of ChinaProject(52174242)supported by the National Science and Technology of ChinaProject(52130406)supported by the National Science and Technology Major Project of China。
文摘Roasting bastnaesite concentrates is a crucial process in extracting rare earths.This study explored an efficient suspension roasting technology and investigated the bastnaesite pyrolysis and cerium(Ce)oxidation.Relevant analytical tests were applied to evaluate the phase and surface property variations of bastnaesite,and isothermal kinetic analysis of bastnaesite pyrolysis and Ce oxidation was performed.The results revealed that bastnaesite decomposed rapidly and accompanied by Ce oxidation,and the gas-solid products were identified as CO_(2),Ce_(7)O_(12),La_(2)O_(3),CeF_(3) and LaF_(3),with Ce oxidation restricted by bastnaesite pyrolysis.As roasting time prolonged,cracks and pores appeared on bastnaesite surface;the BET specific surface and pore diameter increased.In later roasting period,the pore diameter continued to increase but the specific surface decreased,assigned to particle fusion agglomeration and pore consolidation.Additionally,the surface C content reduced and Ce(Ⅳ)content increased gradually as roasting progressed.The reaction kinetics all followed Avrami-Erofeev equations,the reaction orders of bastnaesite pyrolysis and Ce oxidation decreased with decreasing reaction temperature.The calculated activation energies at lower temperatures were higher than those calculated at higher temperatures.This study analyzed the bastnaesite reaction mechanism to supply a reference for the application of suspension roasting technology in bastnaesite smelting.
基金supported by the National Key Laboratory of Energetic Materials, China (Grant No. 2023-LB-036-09).
文摘In order to analyze the influences of storage aging on the safety of typical elemental explosives,the aged cyclotrimethylene trinitramine(RDX)and cyclotetramethylene tetranitramine(HMX)were prepared by isothermal aging tests.The reaction thresholds of aged RDX and HMX under any ignition probability were studied by Langlie-Optimal D method.The thermal decomposition characteristics of RDX and HMX after aging were analyzed by DSC and ARC.Experimental results showed that compared with unaged RDX and HMX,on the one hand,the critical impact energy and critical friction of RDX and HMX aged for 14,28,and 56 days are significantly reduced at an explosion probability of 50%,0.01%,and 0.0001%,respectively.With the increase of aging time,the mechanical sensitivity of RDX and HMX increases obviously.On the other hand,the initial decomposition temperature of RDX and HMX after 56 days of aging decreases,the decomposition heat decreases,the activation energy increases,and the reaction difficulty increases.
基金Project (2014CB643405) supported by National Research Development Program of China
文摘The equilibrium adsorption isotherm and kinetic of the sorption process for W and Mo on macro chelating resin D403 were investigated on single Na2 Mo O4 and Na2WO4 solutions.The sorption isotherm results show that the adsorption process of W obeys the Freundlich model very well whereas the exchange process with Mo approximately follows the Henry model.The kinetic experiments show that the intraparticle diffusion process was the rate-determining step for W sorption on the resin,and the corresponding activation energy is calculated to be 21.976 k J/mol.
基金Project(2008BAB35B04) supported by the National Key Technology R&D Program of China
文摘Brine,which is used to produce high-purity magnesia,was purified by XSC-700 to remove boron.Boron adsorption capacity of XSC-700 was investigated by varying the initial boron concentration,temperature,resin/brine ratio and stirring speed,while keeping the diameter at constant.The results show that boron adsorption capacity increases with increasing boron concentration,temperature,and decreases with increasing resin/brine ratio.And the stirring speed could slightly affect the boron adsorption capacity.The adsorption kinetics obeys the pseudo-second-order model.Equilibrium data were both examined by Freundlich and Langmuir isotherm equations and it can be well represented by the Freundlich isotherm equation.
基金supported by grants from the Brazilian Agency Coordination of Graduate Level Training(CAPES,project 0366/09-9)State of So Paulo Research Support Foundation(FAPESP-Brazil,project 2005/60159-7)
文摘Endotoxins(also known as lipopolysaccharides(LPS)) are undesirable by-products of recombinant proteins,purified from Escherichia coli.LPS can be considered stable under a wide range of temperature and pH,making their removal one of the most difficult tasks in downstream processes during protein purification.The inherent toxicity of LPS makes their removal an important step for the application of these proteins in several biological assays and for a safe parenteral administration.Immobilized metal affinity chromatography(IMAC) enables the affinity interactions between the metal ions(immobilized on the support through the chelating compound) and the target molecules,thus enabling high-efficiency separation of the target molecules from other components present in a mixture.Affinity chromatography is applied with Ca2+-iminodiacetic acid(IDA) to remove most of the LPS contaminants from the end product(more than90%).In this study,the adsorption of LPS on an IDA-Ca2+ was investigated.The adsorption Freundlich isotherm of LPS-IDA-Ca2+ provides a theoretical basis for LPS removal.It was found that LPS is bound mainly by interactions between the phosphate group in LPS and Ca2+ ligands on the beads.The factors such as pH(4.0 or 5.5) and ionic strength(1.0 mol/L) are essential to obtain effective removal of LPS for contaminant levels between endotoxin' concentration values less than100 EU/mL and 100 000 EU/mL.This new protocol represents a substantial advantage in time,effort,and production costs.
基金Project(11JJ2031)supported by the Key Project of Natural Science Foundation of Hunan Province,China
文摘To establish a theoretical foundation for simultaneous removal of multi-heavy metals,the adsorption of Cu（Ⅱ） and Pb（Ⅱ） ions from their single and binary systems by Ca-alginate immobilized activated carbon and Saccharomyces cerevisiae （CAS） was investigated.The CAS beads were characterized by Scanning electron microscope （SEM） and Fourier transformed infrared spectroscopy （FTTR）.The effect of initial pH,adsorbent dosage,contact time and initial metal ions concentration on the adsorption process was systematically investigated.The experimental maximum contents of Cu（Ⅱ） and Pb（Ⅱ） uptake capacity were determined as 64.90 and 166.31 mg/g,respectively.The pseudo-second-order rate equation and Langmuir isotherm model could explain respectively the kinetic and isotherm experimental data of Cu（Ⅱ） and Pb（Ⅱ） ions in single-component systems with much satisfaction.The experimental adsorption data of Cu（Ⅱ） and Pb（Ⅱ） ions in binary system were best described by the extended Freundlich isotherm and the extended Langmuir isotherm,respectively.The removal of Cu（lⅡ） ions was more significantly influenced by the presence of the coexistent Pb（Ⅱ） species,while the Pb（Ⅱ） removal was affected slightly by varying the initial concentration of Cu（Ⅱ）.The CAS was successfully regenerated using 1 mol/L HNO3 solution.
基金Project(10200202002) supported by the National Tobacco Monopolistic Bureau of China project(40473006) supportedby the National Natural Science Foundation of China project(2006KJ010A) supported by the Natural Science Key Research Foundation ofAnhui Province
文摘In order to amend the superficial performance of palygorskite and improve its application, the natural palygorskite(NP) was treated in the dipping and ionic exchanging experiments using 6mol/L hydrochloric acid treatment. The performance and pore structure of the treated palygorskite(TP) were investigated by means of microscope analyses, FT-IR, XRF, BET-SSA and full hole distribution analytical techniques. The results show that the hydrochloric acid treatment can make the gracile and aggregating compact crystal bundles inside palygorskite clay broken and dispersed, the roughness of microcrystalline surface increases, which not only can dissolve or remove dolomite but vary the superficial performance of palygorskite to some degree. The specific surface area and pore volume increase a lot, while the mean pore size decreases. The pore structure of TP changes remarkably compared with that of NP after 6mol/L hydrochloric acid treatment, and the relevant physicochemical performance can be improved.
基金Project(51008106)supported by the National Natural Science Foundation of China
文摘A batch experiment was conducted to investigate the adsorption of an acid dye(Acid Orange 51) and a basic dye(Safranine) from aqueous solutions by the sludge-based activated carbon(SBAC). The results show that the adsorption of Acid Orange 51 decreases at high p H values, whereas the uptake of Safranine is higher in neutral and alkaline solutions than that in acidic conditions. The adsorption time needed for Safranine to reach equilibrium is shorter than that for Acid Orange 51. The uptakes of the dyes both increase with temperature increasing, indicating that the adsorption process of the dyes onto SBAC is endothermic. The equilibrium data of the dyes are both best represented by the Redlich-Peterson model. At 25 °C, the maximum adsorption capacities of SBAC for Acid Orange 51 and Safranine are 248.70 mg/g and 525.84 mg/g, respectively. The Elovich model is found to best describe the adsorption process of both dyes, indicating that the rate-limiting step involves the chemisorption. It can be concluded that SBAC is a promising material for the removal of Acid Orange 51 and Safranine from aqueous solutions.
基金Project(51208173)supported by the National Natural Science Foundation of ChinaProject(ZR2014EEM005)supported by the Natural Science Foundation of Shandong Province,China
文摘The adsorption capacity of Pb(Ⅱ) on litchi pericarps was investigated as a function of temperature,pH,and adsorbent dose using batch experiments.The experimental data obtained were evaluated using adsorption equilibrium isotherms and a kinetic model.Additionally,the removal of Pb(Ⅱ) in leachate of litchi pericarps was also evaluated.The results show that litchi pericarps exhibit a high adsorption capacity to Pb(Ⅱ),with the maximum removal efficiency occurring at a temperature of 25 ℃,a pH of 6.0-7.0 and an adsorbent dosage of 10 g/L.Langmuir and Freundlich isotherms and the pseudo-second-order kinetic model can all fit the equilibrium adsorption satisfactorily,with correlation coefficients(R^2) of 0.9935,0.9918 and 1.0,respectively.An average removal efficiency of 66.65% is found for Pb(Ⅱ) in leachate of litchi pericarps.
基金Shahid Hashemi Nejad Gas refinery for supporting this project
文摘Different mesoporous activated carbons were prepared by both chemical and physical activation processes and were examined for methane uptake in the presence of water.Methane isotherms were obtained at wet condition by wetting samples with water at mass ratio of water/carbon(R) close to 1.0.To compare,the amount of methane storage were also measured at dry situation.The maximum amount of methane stored was attained as 237 V/V at R=1.0 by hydrate formation at the methane critical pressure.In the next step,mass ratios of water/carbon were changed to investigate various amount of water for methane storage enhancement.Two other values of mass ratio of water/carbon(R=0.8 and 1.4) were selected and methane isotherms were obtained at the same conditions.Maximum values of 210 and 248 V/V were reached for methane storage,respectively.It was also observed that,in the pressure range lower than hydrate pressure,by increasing water ratio the hydrate formation pressure was decreased and methane uptake was much less than that of dry condition due to pore filling by water.
基金Project(20171BAB206005)supported by the Natural Science Foundation of Jiangxi Province,ChinaProject(20153BCB23023)supported by the Training Program Foundation for Young Scientists of Jiangxi Province,ChinaProject(51961026)supported by the National Natural Science Foundation of China。
文摘The microstructure and Gd-rich phase evolution of as-cast AZ31-xGd(x=0,1.5 wt.%,2.0 wt.%and 2.5 wt.%)magnesium alloys during semi-solid isothermal heat treatment were investigated deeply in the present work.Results showed that the lamellar(Mg,Al)3Gd phases transformed into the particle-like Al2Gd phases in AZ31 magnesium alloys with Gd addition during semi-solid isothermal heat treatment,leading to yielding more sphericalα-Mg grains.When Gd content is 2.0 wt.%,the size of semi-solid spherical grains reaches the minimum.The main mechanism of grain refinement lies in the remelting of dendritic branches as well as the auxiliary effect of a small number of Al2Gd particles as grain refining inoculants.Meanwhile,Al2Gd particles enriched at the solid-liquid interfaces can remarkably retard the growth rate ofα-Mg grains.A reduction of deformation resistance has been successfully achieved in AZ31-2.0Gd magnesium alloy after semi-solid isothermal heat treatment,which shows a moderate compressive deformation resistance(230 MPa),comparing to the as-cast AZ31 magnesium alloy(280 MPa)and semi-solid AZ31 magnesium alloy(209 MPa).
文摘The potential of di-(m-Formylphenol)-1,2-cyclohexandiimine as an environmentally friendly corrosion inhibitor for steel was investigated in 1 mol/L HCl using potentiodynamic polarization, electrochemical impedance spectroscopy and chronoamperometry measurements. All electrochemical measurements suggest that this compound is an excellent corrosion inhibitor for mild steel and the inhibition efficiency increases with the increase in inhibitor concentration. The effect of temperature on the corrosion behavior of mild steel with the addition of the Schiff base was studied in the temperature range from 25 °C to 65 °C. It is found that the adsorption of this inhibitor follows the Langmuir adsorption isotherms. The value of activation energy and the thermodynamic parameters such as ΔHads, ΔSads, Kads and ΔGads were calculated by the corrosion currents at different temperatures using the adsorption isotherm. The morphology of mild steel surface in the absence and presence of inhibitor was examined by scanning electron microscopy(SEM) images.
基金Project(2004C33068) supported by the Science and Technology Programs of Zhejiang Province,ChinaProject(20100933B17) supported by the Social Development and Science Research Program of Hangzhou,China
文摘The isotherm,mechanism and kinetics of carbon tetrachloride(CT) adsorption by polyacrylonitrile-based activated carbon fiber(PAN-ACF) were investigated in batch reactors and a continuous flow reactor,and the regeneration of PAN-ACF was also studied.Freundlich and Dubinin-Radushkevich(D-R) adsorption equations can well describe the adsorption isotherm.CT is mainly adsorbed on the exterior surface of PAN-ACF with low boundary layer effect and rate-controlling step of intra-particle diffusion.The adsorption dynamics in the batch reactor well fits with the pseudo-first-order model,and the breakthrough curves in the continuous flow reactor can be well described by the Yoon-Nelson model.The ACF can be recycled through thermal regeneration,whereas the adsorption capacity decreases from 7.87 to 4.98 mg/g after the fourth regeneration.78%-94%of CT can be removed from the wastewater of a fluorine chemical plant on a pilot scale,which confirms the efficacy of ACF under industrial conditions.The results indicate that PAN-ACF is applicable to CT removal from wastewater.
基金Project(UKM-GUP-BTT-07-25-170) supported by Universiti Kebangsaan Malaysia
文摘The inhibition ability of 4-amino-5-phenyl-4H-1, 2, 4-trizole-3-thiol （APTT）, ethylenediaminetetra-acetic acid （EDTA） and thiourea （TU） for mild steel corrosion in 1.0 moFL HC1 solution at 30 ℃ was investigated. Tafel polarization and electrochemical impedance spectroscopy （EIS） were used to investigate the influence of these organic compounds as corrosion inhibitors of mild steel in 1.0 mol/L HC1 solution at 30 ℃. The inhibition mechanism was discussed in terms of Langrnuir isotherm model. Results obtained from Tafel polarization and impedance measurements are in a good agreement. The inhibition efficiency increases with the increase of the inhibitor concentration. The adsorption of the inhibitors on the mild steel surface follows Langmuir adsorption isotherm and the free energy of adsorption AGads indicates that the adsorption of APTT, EDTA, and TU molecules is a spontaneous process and a typical chemisorption.
基金Project(2012BAJ24B03)supported by the National Science and Technology Support Program of China
文摘A low-cost adsorbent modified kaolin clay(MKC) was synthesized and utilized for Cr(VI) removal from aqueous solution. Adsorption experiments were carried out as a function of adsorbent dosage, solution pH, Cr(VI) mass concentration, contact time, electrolyte, and temperature. It is found that the adsorption efficiency is high within a wide pH range of 2.5-11.5, and equilibrium is achieved within 180 min. Increases in temperature and electrolyte concentration decrease the adsorption. The adsorption follows the pseudo-second-order kinetic model. The Langmuir isotherm shows better fit than Freundlich isotherm. The maximum uptake capacities calculated from the Langmuir model are 15.82, 15.55 and 15.22 mg/g at 298, 308 and 318 K, respectively. Thermodynamic parameters reveals the spontaneous and exothermic nature of the adsorption. The FTIR study indicates that hydroxyl groups, NH4+ ions and NO3- ions on MKC surface play a key role in Cr(VI) adsorption. The Cr(VI) desorbability of 86.53% is achieved at a Na2CO3 solution. The results show that MKC is suitable as a low-cost adsorbent for Cr(VI) removal which has higher adsorption capacity and faster adsorption rate at pH close to that where pollutants are usually found in the environment.
基金Project(200202AA305207) supported by the National High Technology Research and Development Program of China
文摘The ablation properties of C/C composites with four different needled preforms prepared by isothermal chemical vapor infiltration （ICVI）, which are super-thin mat lay-up, 0°/90° weftless fabric lay-up, 0°/45° weftless fabric lay-up and 0°/45° twill fabric lay-up, were quantitatively evaluated by performing the ablation tests with an engine torch. And their ablation discrepancies were analyzed according to the surface characteristic, porosity and thermal diffusivity. The results show that the 0°/45° weftless composite has a fiat eroded surface with no obvious macroscopic pits. Its thickness and mass erosion rates are decreased by about 46.8% and 34.8%, 25.0% and 27.5%, and 17.5% and 19.4% compared with those of the mat, the 0°/90° weftless and the 0°/45° twill composites, respectively. The ablation properties are mainly controlled by the thermo-chemical effect （oxidation）, and a little by the thermo-mechanical effect （mechanical denudation）. The needling fiber bundles play an important role in accelerating the ablation process and resulting in the heterogeneous ablation.
