RBOE is a new type of DNAN-based high-energy melt-cast mixed explosive,whose safety under thermal stimulation is significantly affected by heating conditions and venting area of the warhead.Based on the thermal decomp...RBOE is a new type of DNAN-based high-energy melt-cast mixed explosive,whose safety under thermal stimulation is significantly affected by heating conditions and venting area of the warhead.Based on the thermal decomposition reaction characteristics and combustion characteristics of each component of RBOE explosive,the cook-off calculation models of RBOE warhead before and after ignition were established.In addition,closed and vented warheads were designed,as well as fast and slow cook-off test devices.The cook-off characteristics and thermal safety venting area of RBOE warhead were extensively studied.The results showed that the closed RBOE warhead underwent deflagration reaction under both slow and fast cook-off conditions.The calculation result of the shell wall temperature before slow cookoff ignition response of the warhead was 454.06 K,with an error of+1.75%compared to the test result of462.15 K,and the temperature rise rate calculated was in good agreement with the test.The calculated ignition time of RBOE warhead under fast cook-off was 161 s,with an error of+8.8%compared to the test result of 148 s,which verified the accuracy of cook-off model of RBOE warhead before ignition.According to the cook-off calculation model of the warhead after ignition and cook-off test of the vented warhead,it was determined that the thermal safety venting area was 1124.61 mm^(2)for fast cook-off and 530.66 mm~2 for slow cook-off,effectively preventing the reaction of warhead above combustion.Therefore,this study provides a scientific basis for the thermal safety design and evaluation of insensitive warheads.展开更多
In the field of calculating the attack area of air-to-air missiles in modern air combat scenarios,the limitations of existing research,including real-time calculation,accuracy efficiency trade-off,and the absence of t...In the field of calculating the attack area of air-to-air missiles in modern air combat scenarios,the limitations of existing research,including real-time calculation,accuracy efficiency trade-off,and the absence of the three-dimensional attack area model,restrict their practical applications.To address these issues,an improved backtracking algorithm is proposed to improve calculation efficiency.A significant reduction in solution time and maintenance of accuracy in the three-dimensional attack area are achieved by using the proposed algorithm.Furthermore,the age-layered population structure genetic programming(ALPS-GP)algorithm is introduced to determine an analytical polynomial model of the three-dimensional attack area,considering real-time requirements.The accuracy of the polynomial model is enhanced through the coefficient correction using an improved gradient descent algorithm.The study reveals a remarkable combination of high accuracy and efficient real-time computation,with a mean error of 91.89 m using the analytical polynomial model of the three-dimensional attack area solved in just 10^(-4)s,thus meeting the requirements of real-time combat scenarios.展开更多
In the paper, the distribution characteristics of strong earthquakes in Sichuan-Yunnan area and their geological tectonic background, especially the relation to Sichuan-Yunnan and Sichuan-Qinghai crustal blocks have b...In the paper, the distribution characteristics of strong earthquakes in Sichuan-Yunnan area and their geological tectonic background, especially the relation to Sichuan-Yunnan and Sichuan-Qinghai crustal blocks have been studied. The main results are: a) Strong earthquakes in Sichuan-Yunnan area distribute mainly in Sichuan-Yunnan and Sichuan-Qinghai crustal blocks; b) Most of strong earthquakes of the two blocks distribute mainly along their boundary faults; c) A few strong earthquakes are not obviously related to active faults. It shows that the relation between strong earthquakes and geological tectonics can be very complex; d) There is a certain correlativity for seismic activities among boundary faults of the two blocks, but they have different features; e) There are some anomalous changes of velocity structures in the deep crust of boundary faults of the two blocks. Many boundary faults, especially Longmenshan fault, cut obviously the Moho discontinuity. The Xianshuihe fault, a typical strike-slip fault, has no obvious indication of cutting the Moho discontinuity, but has distinct low-velocity zone in different depths.展开更多
The essence and the main contribution of this paper are consisted of the suggested novel method for estimation of a projected surface area of an irregularly shaped fragment, which represents a significant step toward ...The essence and the main contribution of this paper are consisted of the suggested novel method for estimation of a projected surface area of an irregularly shaped fragment, which represents a significant step toward a new method of an aerodynamic force estimation of a fragment motion through a resistive medium. The suggested method is to use a tri-axial ellipsoid that has a continuous surface(given as a mathematical function) to approximate an irregularly shaped fragment so that the fragment trajectory can be estimated faster taking into consideration that the aerodynamic force is proportional to a projected surface area of the fragment.During their motion, fragments can take any orientation relative to the velocity vector and aerodynamic force is proportional to a projected surface area of fragment perpendicular to the velocity vector,so it is necessary to have a method for correct estimation of the projected area in an arbitrary direction relatively to the fragment.The model was validated with analytical and CAD techniques, and verified using 3D model of a real fragment. The comparison of the projected surface area values for the fragment, obtained using the CAD tools and using our model, are generally in good agreement, This method represents a step toward modeling that does not require a CFD result for estimation of the aerodynamic force of irregularly shaped bodies.展开更多
Solving the financing problem in rural areas and improving the level of economic development in rural areas become important guarantees for the expansion of domestic demand. This research, through studying the current...Solving the financing problem in rural areas and improving the level of economic development in rural areas become important guarantees for the expansion of domestic demand. This research, through studying the current situation of rural financing, pointed out the main factors restricting the financing in rural areas, such as high risk credit, slow income growth, high financing cost and difficult mortgage and guaranteed loans. Based on those, the author worked out the objectives and direction of China＇s rural financing reform, from two aspects of path selection of reform and innovation and specific embodiments for adjusting the overall reconstruction, and put forward some relevant countermeasures.展开更多
3 degrees of freedom(DOF)exterior ballistic computer models are used in fragment studies to calculate individual trajectories of each fragment based on drag coefficient and the projected(presented)area in the directio...3 degrees of freedom(DOF)exterior ballistic computer models are used in fragment studies to calculate individual trajectories of each fragment based on drag coefficient and the projected(presented)area in the direction of velocity of center of mass.The expectation of a randomly distributed projected area is commonly used for fragments that tumble(random rotation)during flight.We forecast a model where the expected drag coefficient is dependent of shape and Mach number.Rotation or tumbling only affects the expected projected area.Models of projected areas during tumbling and rotation are presented.An examination of the data by Mc Cleskey(1988)indicates that the volume of the fragment to the power of2/3 is a better parameter to characterize the drag coefficient of the fragments than the maximum projected area.Hydrocode simulations are used to verify results and to study projected area and drag coefficient of fragments.展开更多
There were differences between real boundary and blast hole controlling boundary of irregular mined-out area in underground metal mines. There were errors in numerical analysis of stability for goaf, if it was analyze...There were differences between real boundary and blast hole controlling boundary of irregular mined-out area in underground metal mines. There were errors in numerical analysis of stability for goaf, if it was analyzed as regular 3D mined-out area and the influence of coupling stress-seepage-disturbance was not considered adequately. Taking a lead zinc mine as the background, the model was built by the coupling of Surpac and Midas-Gts based on the goaf model precisely measured by CMS.According to seepage stress fundamental equations based on the equivalent continuum mechanical and the theory about equivalent load of dynamic disturbance in deep-hole blasting, the stability of mined-out area under multi-field coupling of stress-seepage-dynamic disturbance was numerically analyzed. The results show that it is more consistent between the numerical analysis model based on the real model of irregular 3D shape goaf and the real situation, which could faithfully reappear the change rule of stress–strain about the surrounding rock under synthetic action of blasting dynamic loading and the seepage pressure. The mined-out area multi-field coupling formed by blasting excavation is stable. Based on combination of the advantages of the CMS,Surpac and Midas-Gts, and fully consideration of the effects of multi-field coupling, the accurate and effective way could be provided for numerical analysis of stability for mined-out area.展开更多
Employing the pot experiment of the complete random block design with 6 replications,four varieties of japonica rice (Fujisaka 5,Honenwase,Akitakomachi and Taichung 65) were used to study the varietal differences in l...Employing the pot experiment of the complete random block design with 6 replications,four varieties of japonica rice (Fujisaka 5,Honenwase,Akitakomachi and Taichung 65) were used to study the varietal differences in leaf nitrogen content(LNC) and leaf area during mature period,their relation and effects to the ripening rate.The results showed that(1) thee were varietal differences in LNC at the heading stage and the LNC decrease rate during the matue period,the high LNC at the heading stage was related to the rapid LNC decrease.(2) There were two phases of the leaf area changing process during the mature period,first was the stable,and second was the decreased phase.There was varietal difference in the critical time of phase 1 and phase 2.The hign leaf area in the phase 1 was in relation to the rapid leaf area decrease in the phase 2.It was not found that there was relation between the leaf quality and quantity.(3)It wa unfavorable to the ripening rate for the high leaf area at the heading stage and the rapid decrease of the leaf area during the mature period.(4)It was put forward that the super high yield rice variety should possess the not very high leaf area and high LNC at the heading stage,slow senescence in the leaf area during the mature period.展开更多
The three-pool and first-order model separates the mineralizable organic carbon into active,slow,and passive carbon pools.This paper used the model and decomposition curves of the soil organic carbon to fit the active...The three-pool and first-order model separates the mineralizable organic carbon into active,slow,and passive carbon pools.This paper used the model and decomposition curves of the soil organic carbon to fit the active pool and its decomposition rate,slow pool and its decomposition rate.The results showed that the size of the active pool from different profiles accounted for 2.09%-3.08% of the total soil organic carbon and the mean residue time was 3.57-17.21 days.And the size of the slow pool accounted for 3.19%-43.55% and the mean residue time was 1.12-4.94 years.Acid hydrolysis（6M HCl） was used to fractionate the passive organic carbon,which accounted for 50.83%-94.44% of the total soil organic carbon.展开更多
Total concentrations of arsenic, lead, cadmium, mercury, nickel, chromium, and copper in the soils from near a coal mine area in southwest Guizhou, China, were measured to evaluate the level of contamination, and the ...Total concentrations of arsenic, lead, cadmium, mercury, nickel, chromium, and copper in the soils from near a coal mine area in southwest Guizhou, China, were measured to evaluate the level of contamination, and the potential ecological risks posed by the heavy metals were quantitatively estimated. Results reveal that all heavy metals/metalloid exceeded the background values for soil environmental quality of heavy metals in Guizhou area. Geo-accumulation index(I_(geo)) showed that arsenic had the highest contamination level(I_(geo)=4) among the seven heavy metals/metalloid, and the contamination levels of mercury and lead were also relatively high(I_(geo)=3). Pearson correlation and cluster analysis identified that mercury, copper and arsenic had a relationship, and their presence might be mainly related to mining activity, coal and oil combustion, and vehicle emissions. Improved Nemerow index indicated that the overall level of heavy metal contamination in the studied area ranged from moderately–heavily contaminated to heavily contaminated level. Potential ecological risk index(R_I) analysis manifested that the whole ecological risk level ranged from high degree to very high degree(325.30≤R_I≤801.02) in the studied soil samples, and the potential ecological risk factors (E_r^i) of heavy metals/metalloid were as follows: Hg > As > Cd > Pb > Cu > Ni > Cr, and the E_r^i of Hg and As reached very high risk grade.展开更多
Introduction There are big disputes on the uplift of the Tibetan Plateau. Some scientists believe the plateau uplifted to its highest elevation by 14Ma BP,and it decreased in elevation afterward. The second idea about...Introduction There are big disputes on the uplift of the Tibetan Plateau. Some scientists believe the plateau uplifted to its highest elevation by 14Ma BP,and it decreased in elevation afterward. The second idea about the uplift of the plateau was similar to the first one in tectonic theory, but they consider the time of C3 plant change to C4 in the South Asia, as the time when the plateau reached its highest elevation. This time is 8Ma BP. The third idea, the most Chinese scientists believed, the nearest uplift of the plateau took place since 3 4Ma BP. The occurrence of fault depression and gravel deposit with large thickness in the inner and the marge of the plateau represented the speed uplift. After the collision of the India plate and the Eurasia plateau by the 36Ma, the Tibetean area uplifted several times, but it had been planed to lower area. The plateau with 4500m elevation formed in the Quaternary. While our recent research in the Kunlun Pass area suggest , the nearest uplift occurred at the border of the Early and Middle Pleistocene, and before that time, the elevation of this area was no more than 1500 m.展开更多
For better reflecting the interactive defense between targets in practical combat scenarios,the basic weapon-target allocation(WTA)framework needs to be improved.A multi-stage attack WTA method is proposed.First,a def...For better reflecting the interactive defense between targets in practical combat scenarios,the basic weapon-target allocation(WTA)framework needs to be improved.A multi-stage attack WTA method is proposed.First,a defense area analysis is presented according to the targets’positions and the radii of the defense areas to analyze the interactive coverage and protection between targets’defense areas.Second,with the coverage status and coverage layer number,a multi-stage attack planning method is proposed and the multi-stage attack objective function model is established.Simulation is conducted with interactive defense combat scenarios,the traditional WTA method and the multi-stage WTA method are compared,and the objective function model is validated with the Monte-Carlo method.The results suggest that if the combat scenario involves interactive coverage of targets’defense areas,it is imperative to analyze the defense areas and apply the multi-stage attack method to weakening the target defense progressively for better combat effectiveness.展开更多
The deepwater area of southern Qiongdongnan Basin is a hydrocarbon exploration frontier and mainly located on the continental slope in the northwestern South China Sea.Its tectonic and depositional evolution is simila...The deepwater area of southern Qiongdongnan Basin is a hydrocarbon exploration frontier and mainly located on the continental slope in the northwestern South China Sea.Its tectonic and depositional evolution is similar to the typical marginal deepwater areas abroad where oils have been discovered.Favorable hydrocarbon conditions in this area are as follows:(1) three sets of source rocks (including lacustrine mudstone of Eocene,coastal plain coal-bearing strata and semi-closed shallow sea mudstone of Oligocene,and marine mudstone展开更多
Dynamic analysis steps and general flow of fast lagrangian analysis of continua in 3 dimensions(FLAC3D) were discussed. Numerical simulation for influence of excavation and blasting vibration on stability of mined-out...Dynamic analysis steps and general flow of fast lagrangian analysis of continua in 3 dimensions(FLAC3D) were discussed. Numerical simulation for influence of excavation and blasting vibration on stability of mined-out area was carried out with FLAC3D. The whole analytical process was divided into two steps, including the static analysis and the dynamic analysis which were used to simulate the influence of excavation process and blasting vibration respectively. The results show that the shape of right upper boundary is extremely irregular after excavation, and stress concentration occurs at many places and higher tensile stress appears. The maximum tensile stress is higher than the tensile strength of rock mass, and surrounding rock of right roof will be damaged with tension fracture. The maximum displacement of surrounding rock is 4.75 mm after excavation. However, the maximum displacement increases to 5.47 mm after the blasting dynamic load is applied. And the covering area of plastic zones expands obviously, especially at the foot of right upper slope. The analytical results are in basic accordance with the observed results on the whole. Damage and disturbance on surrounding rock to some degree are caused by excavation, while blasting dynamic load increases the possibility of occurrence of dynamic instability and destruction further. So the effective supporting and vibration reducing measures should be taken during mining.展开更多
基金National Natural Science Foundation of china(Grant No.12402468)。
文摘RBOE is a new type of DNAN-based high-energy melt-cast mixed explosive,whose safety under thermal stimulation is significantly affected by heating conditions and venting area of the warhead.Based on the thermal decomposition reaction characteristics and combustion characteristics of each component of RBOE explosive,the cook-off calculation models of RBOE warhead before and after ignition were established.In addition,closed and vented warheads were designed,as well as fast and slow cook-off test devices.The cook-off characteristics and thermal safety venting area of RBOE warhead were extensively studied.The results showed that the closed RBOE warhead underwent deflagration reaction under both slow and fast cook-off conditions.The calculation result of the shell wall temperature before slow cookoff ignition response of the warhead was 454.06 K,with an error of+1.75%compared to the test result of462.15 K,and the temperature rise rate calculated was in good agreement with the test.The calculated ignition time of RBOE warhead under fast cook-off was 161 s,with an error of+8.8%compared to the test result of 148 s,which verified the accuracy of cook-off model of RBOE warhead before ignition.According to the cook-off calculation model of the warhead after ignition and cook-off test of the vented warhead,it was determined that the thermal safety venting area was 1124.61 mm^(2)for fast cook-off and 530.66 mm~2 for slow cook-off,effectively preventing the reaction of warhead above combustion.Therefore,this study provides a scientific basis for the thermal safety design and evaluation of insensitive warheads.
基金National Natural Science Foundation of China(62373187)Forward-looking Layout Special Projects(ILA220591A22)。
文摘In the field of calculating the attack area of air-to-air missiles in modern air combat scenarios,the limitations of existing research,including real-time calculation,accuracy efficiency trade-off,and the absence of the three-dimensional attack area model,restrict their practical applications.To address these issues,an improved backtracking algorithm is proposed to improve calculation efficiency.A significant reduction in solution time and maintenance of accuracy in the three-dimensional attack area are achieved by using the proposed algorithm.Furthermore,the age-layered population structure genetic programming(ALPS-GP)algorithm is introduced to determine an analytical polynomial model of the three-dimensional attack area,considering real-time requirements.The accuracy of the polynomial model is enhanced through the coefficient correction using an improved gradient descent algorithm.The study reveals a remarkable combination of high accuracy and efficient real-time computation,with a mean error of 91.89 m using the analytical polynomial model of the three-dimensional attack area solved in just 10^(-4)s,thus meeting the requirements of real-time combat scenarios.
基金State Key Basic Research Development and Programming Project of China (G1998040700/95-13-02-03).
文摘In the paper, the distribution characteristics of strong earthquakes in Sichuan-Yunnan area and their geological tectonic background, especially the relation to Sichuan-Yunnan and Sichuan-Qinghai crustal blocks have been studied. The main results are: a) Strong earthquakes in Sichuan-Yunnan area distribute mainly in Sichuan-Yunnan and Sichuan-Qinghai crustal blocks; b) Most of strong earthquakes of the two blocks distribute mainly along their boundary faults; c) A few strong earthquakes are not obviously related to active faults. It shows that the relation between strong earthquakes and geological tectonics can be very complex; d) There is a certain correlativity for seismic activities among boundary faults of the two blocks, but they have different features; e) There are some anomalous changes of velocity structures in the deep crust of boundary faults of the two blocks. Many boundary faults, especially Longmenshan fault, cut obviously the Moho discontinuity. The Xianshuihe fault, a typical strike-slip fault, has no obvious indication of cutting the Moho discontinuity, but has distinct low-velocity zone in different depths.
文摘The essence and the main contribution of this paper are consisted of the suggested novel method for estimation of a projected surface area of an irregularly shaped fragment, which represents a significant step toward a new method of an aerodynamic force estimation of a fragment motion through a resistive medium. The suggested method is to use a tri-axial ellipsoid that has a continuous surface(given as a mathematical function) to approximate an irregularly shaped fragment so that the fragment trajectory can be estimated faster taking into consideration that the aerodynamic force is proportional to a projected surface area of the fragment.During their motion, fragments can take any orientation relative to the velocity vector and aerodynamic force is proportional to a projected surface area of fragment perpendicular to the velocity vector,so it is necessary to have a method for correct estimation of the projected area in an arbitrary direction relatively to the fragment.The model was validated with analytical and CAD techniques, and verified using 3D model of a real fragment. The comparison of the projected surface area values for the fragment, obtained using the CAD tools and using our model, are generally in good agreement, This method represents a step toward modeling that does not require a CFD result for estimation of the aerodynamic force of irregularly shaped bodies.
文摘Solving the financing problem in rural areas and improving the level of economic development in rural areas become important guarantees for the expansion of domestic demand. This research, through studying the current situation of rural financing, pointed out the main factors restricting the financing in rural areas, such as high risk credit, slow income growth, high financing cost and difficult mortgage and guaranteed loans. Based on those, the author worked out the objectives and direction of China＇s rural financing reform, from two aspects of path selection of reform and innovation and specific embodiments for adjusting the overall reconstruction, and put forward some relevant countermeasures.
文摘3 degrees of freedom(DOF)exterior ballistic computer models are used in fragment studies to calculate individual trajectories of each fragment based on drag coefficient and the projected(presented)area in the direction of velocity of center of mass.The expectation of a randomly distributed projected area is commonly used for fragments that tumble(random rotation)during flight.We forecast a model where the expected drag coefficient is dependent of shape and Mach number.Rotation or tumbling only affects the expected projected area.Models of projected areas during tumbling and rotation are presented.An examination of the data by Mc Cleskey(1988)indicates that the volume of the fragment to the power of2/3 is a better parameter to characterize the drag coefficient of the fragments than the maximum projected area.Hydrocode simulations are used to verify results and to study projected area and drag coefficient of fragments.
基金Project(2012BAK09B02-05)supported by the National"Twelfth Five"Science and Technology Support Program,ChinaProject(51274250)supported by the National Natural Science Foundation of China+2 种基金Project(2013zzts057)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(11KF02)supported by the Research Fund of the State Key Laboratory of Coal Resources and Mine safety,CUMT,ChinaProject(2012M511417)supported by China Postdoctoral Science Foundation
文摘There were differences between real boundary and blast hole controlling boundary of irregular mined-out area in underground metal mines. There were errors in numerical analysis of stability for goaf, if it was analyzed as regular 3D mined-out area and the influence of coupling stress-seepage-disturbance was not considered adequately. Taking a lead zinc mine as the background, the model was built by the coupling of Surpac and Midas-Gts based on the goaf model precisely measured by CMS.According to seepage stress fundamental equations based on the equivalent continuum mechanical and the theory about equivalent load of dynamic disturbance in deep-hole blasting, the stability of mined-out area under multi-field coupling of stress-seepage-dynamic disturbance was numerically analyzed. The results show that it is more consistent between the numerical analysis model based on the real model of irregular 3D shape goaf and the real situation, which could faithfully reappear the change rule of stress–strain about the surrounding rock under synthetic action of blasting dynamic loading and the seepage pressure. The mined-out area multi-field coupling formed by blasting excavation is stable. Based on combination of the advantages of the CMS,Surpac and Midas-Gts, and fully consideration of the effects of multi-field coupling, the accurate and effective way could be provided for numerical analysis of stability for mined-out area.
文摘Employing the pot experiment of the complete random block design with 6 replications,four varieties of japonica rice (Fujisaka 5,Honenwase,Akitakomachi and Taichung 65) were used to study the varietal differences in leaf nitrogen content(LNC) and leaf area during mature period,their relation and effects to the ripening rate.The results showed that(1) thee were varietal differences in LNC at the heading stage and the LNC decrease rate during the matue period,the high LNC at the heading stage was related to the rapid LNC decrease.(2) There were two phases of the leaf area changing process during the mature period,first was the stable,and second was the decreased phase.There was varietal difference in the critical time of phase 1 and phase 2.The hign leaf area in the phase 1 was in relation to the rapid leaf area decrease in the phase 2.It was not found that there was relation between the leaf quality and quantity.(3)It wa unfavorable to the ripening rate for the high leaf area at the heading stage and the rapid decrease of the leaf area during the mature period.(4)It was put forward that the super high yield rice variety should possess the not very high leaf area and high LNC at the heading stage,slow senescence in the leaf area during the mature period.
基金Supported by the Work Project of China Geological Survey (1212010911062)Guangxi Zhuang Autonomous Region Innovation Project (0842008)National Natural Science Foundation (40872213)
文摘The three-pool and first-order model separates the mineralizable organic carbon into active,slow,and passive carbon pools.This paper used the model and decomposition curves of the soil organic carbon to fit the active pool and its decomposition rate,slow pool and its decomposition rate.The results showed that the size of the active pool from different profiles accounted for 2.09%-3.08% of the total soil organic carbon and the mean residue time was 3.57-17.21 days.And the size of the slow pool accounted for 3.19%-43.55% and the mean residue time was 1.12-4.94 years.Acid hydrolysis（6M HCl） was used to fractionate the passive organic carbon,which accounted for 50.83%-94.44% of the total soil organic carbon.
基金Project(21467005)supported by the National Natural Science Foundation of China
文摘Total concentrations of arsenic, lead, cadmium, mercury, nickel, chromium, and copper in the soils from near a coal mine area in southwest Guizhou, China, were measured to evaluate the level of contamination, and the potential ecological risks posed by the heavy metals were quantitatively estimated. Results reveal that all heavy metals/metalloid exceeded the background values for soil environmental quality of heavy metals in Guizhou area. Geo-accumulation index(I_(geo)) showed that arsenic had the highest contamination level(I_(geo)=4) among the seven heavy metals/metalloid, and the contamination levels of mercury and lead were also relatively high(I_(geo)=3). Pearson correlation and cluster analysis identified that mercury, copper and arsenic had a relationship, and their presence might be mainly related to mining activity, coal and oil combustion, and vehicle emissions. Improved Nemerow index indicated that the overall level of heavy metal contamination in the studied area ranged from moderately–heavily contaminated to heavily contaminated level. Potential ecological risk index(R_I) analysis manifested that the whole ecological risk level ranged from high degree to very high degree(325.30≤R_I≤801.02) in the studied soil samples, and the potential ecological risk factors (E_r^i) of heavy metals/metalloid were as follows: Hg > As > Cd > Pb > Cu > Ni > Cr, and the E_r^i of Hg and As reached very high risk grade.
文摘Introduction There are big disputes on the uplift of the Tibetan Plateau. Some scientists believe the plateau uplifted to its highest elevation by 14Ma BP,and it decreased in elevation afterward. The second idea about the uplift of the plateau was similar to the first one in tectonic theory, but they consider the time of C3 plant change to C4 in the South Asia, as the time when the plateau reached its highest elevation. This time is 8Ma BP. The third idea, the most Chinese scientists believed, the nearest uplift of the plateau took place since 3 4Ma BP. The occurrence of fault depression and gravel deposit with large thickness in the inner and the marge of the plateau represented the speed uplift. After the collision of the India plate and the Eurasia plateau by the 36Ma, the Tibetean area uplifted several times, but it had been planed to lower area. The plateau with 4500m elevation formed in the Quaternary. While our recent research in the Kunlun Pass area suggest , the nearest uplift occurred at the border of the Early and Middle Pleistocene, and before that time, the elevation of this area was no more than 1500 m.
基金the National Natural Science Foundation of China(41871376,41971416,41631072).
文摘For better reflecting the interactive defense between targets in practical combat scenarios,the basic weapon-target allocation(WTA)framework needs to be improved.A multi-stage attack WTA method is proposed.First,a defense area analysis is presented according to the targets’positions and the radii of the defense areas to analyze the interactive coverage and protection between targets’defense areas.Second,with the coverage status and coverage layer number,a multi-stage attack planning method is proposed and the multi-stage attack objective function model is established.Simulation is conducted with interactive defense combat scenarios,the traditional WTA method and the multi-stage WTA method are compared,and the objective function model is validated with the Monte-Carlo method.The results suggest that if the combat scenario involves interactive coverage of targets’defense areas,it is imperative to analyze the defense areas and apply the multi-stage attack method to weakening the target defense progressively for better combat effectiveness.
文摘The deepwater area of southern Qiongdongnan Basin is a hydrocarbon exploration frontier and mainly located on the continental slope in the northwestern South China Sea.Its tectonic and depositional evolution is similar to the typical marginal deepwater areas abroad where oils have been discovered.Favorable hydrocarbon conditions in this area are as follows:(1) three sets of source rocks (including lacustrine mudstone of Eocene,coastal plain coal-bearing strata and semi-closed shallow sea mudstone of Oligocene,and marine mudstone
基金Project (50490272) supported by the National Natural Science Foundation of China project(NCET-05-0687) supportedby Programfor New Century Excellent Talents project (040109) supported bythe Doctor Degree Paper Innovation Engineering of CentralSouth University
文摘Dynamic analysis steps and general flow of fast lagrangian analysis of continua in 3 dimensions(FLAC3D) were discussed. Numerical simulation for influence of excavation and blasting vibration on stability of mined-out area was carried out with FLAC3D. The whole analytical process was divided into two steps, including the static analysis and the dynamic analysis which were used to simulate the influence of excavation process and blasting vibration respectively. The results show that the shape of right upper boundary is extremely irregular after excavation, and stress concentration occurs at many places and higher tensile stress appears. The maximum tensile stress is higher than the tensile strength of rock mass, and surrounding rock of right roof will be damaged with tension fracture. The maximum displacement of surrounding rock is 4.75 mm after excavation. However, the maximum displacement increases to 5.47 mm after the blasting dynamic load is applied. And the covering area of plastic zones expands obviously, especially at the foot of right upper slope. The analytical results are in basic accordance with the observed results on the whole. Damage and disturbance on surrounding rock to some degree are caused by excavation, while blasting dynamic load increases the possibility of occurrence of dynamic instability and destruction further. So the effective supporting and vibration reducing measures should be taken during mining.
