Backoff mechanism is a key component of contention-based medium access control（MAC） layer protocol.It has been shown that the backoff mechanism of IEEE 802.11 standard may be very inefficient especially when the net...Backoff mechanism is a key component of contention-based medium access control（MAC） layer protocol.It has been shown that the backoff mechanism of IEEE 802.11 standard may be very inefficient especially when the network is congested.Numbers of methods have been proposed to tune the contention window（CW） with the aim to achieve the optimal throughput in IEEE 802.11 WLANs.However,the mechanisms do not specifically address proper settings for the variable packet length influence and CW diverging problem.This paper proposes a novel four-way handshaking full-feedback backoff algorithm named adoptive contention window backoff（ACWB） to overcome these drawbacks.The performance of the proposed algorithm is investigated through analysis and simulation.Simulation results demonstrate that the ACWB algorithm provides a remarkable performance improvement in terms of short-term fairness,packet delay and delay jitter,while maintaining an optimal throughput close to the theoretical throughput limit of the IEEE 802.11 distributed coordination function（DCF） access scheme.展开更多
Aseries of [(Fe_(0.6)Co_(0.2)Ni_(0.2))_(0.75-0.03x)B_(0.2)Si_(0.05+0.03x)]_(96)Nb_(4) amorphous alloy composite coatings were prepared by adjusting the silicon content(x=0,1,2,3,4,5,and 6)and their microstructures and...Aseries of [(Fe_(0.6)Co_(0.2)Ni_(0.2))_(0.75-0.03x)B_(0.2)Si_(0.05+0.03x)]_(96)Nb_(4) amorphous alloy composite coatings were prepared by adjusting the silicon content(x=0,1,2,3,4,5,and 6)and their microstructures and tribological properties were investigated by laser cladding technique.Additionally,the effect of Si on the glass forming ability(GFA)of the layers was understood.Results show that an appropriate Si content can refine the microstructure of the FeCoNiBSiNb laser cladding layers and improve the mechanical and tribological properties.The hardness of the coating layer increases monotonically with the Si content.At the Si content of 4.8at%(x=0),the coating layer exhibits a relatively low hardness(734.2HV 0.1).Conversely,at the silicon content of 13.44at%(x=3),the coating layer exhibits the highest hardness(1106HV 0.1).The non-crystalline content and tensile strength exhibit an initial increase,followed by a subsequent decrease.At x=2,the coating exhibits its maximum fracture strength(2880 MPa).However,when x>2,the fracture strength of the coating decreases with an increase in x.Conversely,with an increase in Si content,the wear volume loss initially decreases and then increases.At a Si content of 10.56at%(x=2),the coating exhibits the highest non-crystalline content(42%),the highest tensile strength(2880 MPa),and the most favorable dry friction performance.展开更多
Water is a critical factor affecting the mechanical properties of rocks, leading to their degradation. Understanding the creep mechanical behavior of deep roadway surrounding rock under the influence of underground wa...Water is a critical factor affecting the mechanical properties of rocks, leading to their degradation. Understanding the creep mechanical behavior of deep roadway surrounding rock under the influence of underground water is of great significance. Compression and creep experiments on sandstone with varying water contents were conducted using a deep soft rock five-linked rheological experiment system. The experimental conditions, including water content (0%, 0.8%, 1.6%, 2.4% and 3.3%) and confining pressure (0, 6, 9 and 12 MPa), were determined based on pressure-free water absorption tests and in-situ stress measurements. The experimental results show that the compressive strength, creep failure stress, and dilatancy stress of sandstone decrease exponentially with increasing water content, while they increase exponentially with confining pressure. The ratio of lateral to axial instantaneous strain increases nearly linearly with the increase of stress, and the lateral creep strain characteristics of the sample are more significant than the axial ones. The duration of the attenuation creep stage of sandstone decreases with increasing water content and increases with increasing confining pressure. The lateral strain enters the steady-state creep stage before the axial strain, and the onset time of the accelerated creep stage of lateral strain under the failure stress is earlier than that of axial strain. The long-term strength of sandstone was determined based on the lateral steady-state creep rate curve, showing a negative exponential relationship with water content and a positive exponential relationship with confining pressure. A method for determining the long-term strength of rocks based on the ratio of lateral strain to axial strain (μc) is proposed, which is independent of water content. The research results provide a reliable theoretical basis for the analysis of the long-term stability of roadways under the influence of groundwater and the early prediction of creep failure.展开更多
本文从专家推荐网站入手对学科网站进行研究,以气象学为例,通过检索ISI Current Contents Connect数据库,对学科网站的地理分布、语种分布、信息来源、出版者及关键词进行统计分析,总结出学科网站的一些特点。最后对目前学科网络信息资...本文从专家推荐网站入手对学科网站进行研究,以气象学为例,通过检索ISI Current Contents Connect数据库,对学科网站的地理分布、语种分布、信息来源、出版者及关键词进行统计分析,总结出学科网站的一些特点。最后对目前学科网络信息资源研究提出了自己的看法。展开更多
In order to analyze mechanism of casing damage,the uniaxial compression experiment and creep experiment of interbedded mudstone samples from Sanan development area of Daqing Oilfield under different water contents wer...In order to analyze mechanism of casing damage,the uniaxial compression experiment and creep experiment of interbedded mudstone samples from Sanan development area of Daqing Oilfield under different water contents were carried out.The changes of the mudstone's mechanical parameters and creep characteristics with the increment of water saturation were studied.The results indicate that the rock strength and elastic modulus decrease rapidly with the increment of water content,at the same time,the creep strain and creep strain rate of steady state increase with the increment of water content,and also the steady state creep strain rate is enhanced with the increment of deviatoric stress.Through the creep characteristic curves,a non-linear creep constitutive equation of mudstone considering the change of water contents is established,which will be used in future numerical analysis.展开更多
An experiment about rice milling was made to study on the relationship between the different moisture content of brown rice and the energy consumption, the broken rice rate, the crack rate and the head rice yield. It ...An experiment about rice milling was made to study on the relationship between the different moisture content of brown rice and the energy consumption, the broken rice rate, the crack rate and the head rice yield. It could be concluded that the head rice yield increased at first falls and then along with the raise of moisture content and it could reach the maximum 70.78% when moisture content was 15.5%; the energy consumption of rice milling decreased along with the increase of moisture contents; the broken rice rate fell at first and then increased along with the raise of moisture contents and it could reach the minimum 4.28% when the moisture content was 15.5%.展开更多
Employing the pot experiment of the complete random block design with 6 replications,four varieties of japonica rice (Fujisaka 5,Honenwase,Akitakomachi and Taichung 65) were used to study the varietal differences in l...Employing the pot experiment of the complete random block design with 6 replications,four varieties of japonica rice (Fujisaka 5,Honenwase,Akitakomachi and Taichung 65) were used to study the varietal differences in leaf nitrogen content(LNC) and leaf area during mature period,their relation and effects to the ripening rate.The results showed that(1) thee were varietal differences in LNC at the heading stage and the LNC decrease rate during the matue period,the high LNC at the heading stage was related to the rapid LNC decrease.(2) There were two phases of the leaf area changing process during the mature period,first was the stable,and second was the decreased phase.There was varietal difference in the critical time of phase 1 and phase 2.The hign leaf area in the phase 1 was in relation to the rapid leaf area decrease in the phase 2.It was not found that there was relation between the leaf quality and quantity.(3)It wa unfavorable to the ripening rate for the high leaf area at the heading stage and the rapid decrease of the leaf area during the mature period.(4)It was put forward that the super high yield rice variety should possess the not very high leaf area and high LNC at the heading stage,slow senescence in the leaf area during the mature period.展开更多
A novel copyright protection scheme for digital content is presented, which is a private watermarking scheme based on the watermark embedding in the DCT domain and watermark extraction Using independent component anal...A novel copyright protection scheme for digital content is presented, which is a private watermarking scheme based on the watermark embedding in the DCT domain and watermark extraction Using independent component analysis （ICA）. The system includes the key for watermark extraction and the host image. The algorithm splits the original image into blocks and classifies these blocks based on visual masking, that is, noise visibility function （NVF）. Watermark components with different strength are inserted into chosen direct current components of DCT coefficients according to the classifier. The watermark extraction is based on the characteristic of the statistic independence of the host image, watermark and key. Principle component analysis （PCA） whitening process and FastICA techniques are introduced to ensure a blind watermark extraction without requiring the original image. Experirnental results show the proposed technique is robust under attacks such as image filtering and adding noise, cropping and resizing. In addition, the proposed private watermarking system can be improved to the application of the DTV content protection system.展开更多
Nine inbred lines of rapeseed （Brassica napus L.） used as male were crossed to five recessive genetic male sterile （RGMS） lines used as female to produce 45 single crosses. The crosses, their parents and a check h...Nine inbred lines of rapeseed （Brassica napus L.） used as male were crossed to five recessive genetic male sterile （RGMS） lines used as female to produce 45 single crosses. The crosses, their parents and a check hybrid were tested at two locations during 2007 to 2008 for testing the performance and heterosis of hybrids for seed yield and other characters. Results showed that variations for seed yield, oil content, days to flowering and days to maturity were significant. Mean squares for hybrids were significant for all characters. High heterosis （-4.5%-88.3%）, heterobeltiosis （-15.6%-81.1%） and standard heterosis G34.8%-33.1%） were found for the seed yield. The highest heterosis and heterobeltiosis were found in the cross QH303-4A× 1190. The highest standard heterosis was found in the cross Qianyou8A×Q034. Both positive and negative heterosis of single crosses were detected for the oil content. Small heterosis was found for days to flowering and days to maturity. Among parents, Ⅲ 188, Ⅲ224, and Q034 were proved to be the superior for seed yield when used as parents in most of the hybrid combinations. 2365, Ⅲ224, and QH303-4AB were good for high oil content breeding, Ⅲ 176, 2313 and Qianyou3AB were good for the early hybrid breeding. Total 11 hybrids yielded higher than 2 500 kg·hm^-2 and also gave significantly positive heterosis, heterobeltiosis and standard heterosis. Among them, 10 crosses gave higher oil content than that of check. These crosses can be used in the future breeding program for the seed yield and the oil content. Two crosses including Qianyou3A × Ⅲ224 and Qianyou3A×2313 can be used for the early breeding program.展开更多
Well-sintered polycrystalline cubic boron nitride(PCBN)composites with different contents of cubic boron nitride(CBN) were obtained using Al and TiN as additives under pressure of 5.5 GPa and temperature of 1450 ℃.Th...Well-sintered polycrystalline cubic boron nitride(PCBN)composites with different contents of cubic boron nitride(CBN) were obtained using Al and TiN as additives under pressure of 5.5 GPa and temperature of 1450 ℃.The network structure of CBN grains and bonding materials was observed using scanning electron microscope(SEM).With the help of X-ray diffraction(XRD) analysis,TiB2 and AlN could be determined as main products and Al3 Ti also was detected in the Al-rich samples after sintering process.Furthermore,it was shown that Vickers hardness of composites was improved with the increase of CBN contents.However,the lifetime of PCBN composites was in negative correlation with the amount of CBN in turning GCr15 hardened steels,and the surface roughness of workpieces machined by these PCBN composites also showed the same trend.A series of cutting data confirmed that the low CBN content in PCBN composites could enhance the working durability and improve the surface quality in turning hardened steels.The present experiments also indicated that the lowest value of flank wear was not constant for different PCBN composites when they were used to machine several workpieces with different hardness.展开更多
The effect of sulfur addition/solids content(SA/SC)ratio on heavy metals(e.g.copper,zinc and lead)obtained from mine tailings by indigenous sulfur-oxidizing bacteria was studied,and the changes in the chemical forms o...The effect of sulfur addition/solids content(SA/SC)ratio on heavy metals(e.g.copper,zinc and lead)obtained from mine tailings by indigenous sulfur-oxidizing bacteria was studied,and the changes in the chemical forms of heavy metals after bioleaching were explored.The results show that the solubilization of metals is significantly influenced by SA/SC ratio,and SA/SC ratio of 2.50 is found to be the best for bacterial activity and metal solubilization among six SA/SC ratios tested(such as 1.00,1.33,1.50,1.67,2.00 and 2.50)under the chosen experimental conditions.The pH decreases fast and the maximum solubilizations of copper and zinc are respectively 81.76% and 84.35% while that of lead only reaches 40.36%.After bioleaching,the chemical forms of heavy metals have changed.The metals remained in mine tailings are mainly found in residual fractions,which is harmless to the surrounding environment.展开更多
Visible and near-infrared(VNIR)spectroscopy is an eco-friendly method used for estimating plant nutrient deficiencies.The aim of this study was to investigate the possibility of using VNIR method for estimating Zn con...Visible and near-infrared(VNIR)spectroscopy is an eco-friendly method used for estimating plant nutrient deficiencies.The aim of this study was to investigate the possibility of using VNIR method for estimating Zn content in cherry orchard leaves under field conditions.The study was conducted in 3different locations in Isparta region of Turkey.Fifteen cherry orchards containing normal and Zn deficient plants were chosen,and 60 leaf samples were collected from each location.The reflectance spectra of the leaves were measured with an ASD FieldSpec HandHeld spectroradiometer and a plant probe.The Zn contents of leaf samples were predicted through laboratory analysis.The spectral reflectance measurements were used to estimate the Zn levels using stepwise multiple linear regression analysis method.Prediction models were created using the highest coefficient of determination value.The results show that Zn content of cherry trees can be estimated using the VNIR spectroscopic method(87.5<r2<96.79).Moreover,plant nutrient contents can be estimated without using chemicals.However,further research is necessary to develop a standard method for field conditions.Because spectral reflectance is affected by ecological conditions,agricultural applications and nutrient interactions,more effective models must be developed depending on the geographical location,period and plant type.展开更多
Particle size and content of RDX are the two main factors that affect the burning stability of RDX-based propellants. However, these effects and the corresponding mechanisms are still controversial. In this work, we i...Particle size and content of RDX are the two main factors that affect the burning stability of RDX-based propellants. However, these effects and the corresponding mechanisms are still controversial. In this work, we investigated the physicochemical processes during burning and the corresponding mechanisms through the technologies of structure compactness analysis on the base of voidage measurement and theoretical interfacial area estimation, apparent burning rate measurement using closed vessel(CV)and extinguished burning surface characterization relying on interrupted closed vessel(ICV) and scanning electron microscope(SEM). The results indicate that the voidage increased with the increase of RDX content and particle size due to the increasing interfacial area and increasing interface gap size,respectively. The apparent burning rate increased with the increase of RDX particle size because of the decreasing RDX specific surface area on the burning surface, which could decrease the heat absorbing rates of the melting and evaporation processes of RDX in the condensed phase. Similarly, the apparent burning rate decreased with the increase of RDX content at pressures lower than around 55 MPa due to the increasing RDX specific surface area. Whereas, an opposite trend could be observed at pressures higher than around 55 MPa, which was attributed to the increasing heat feedback from the gas phase as the result of the increasing propellant energy. For propellants containing very coarse RDX particles, such as 97.8 and 199.4 μm average size, the apparent burning rate increased stably with a flat extinguished surface at pressures lower than around 30 MPa, while increased sharply above around 30 MPa with the extinguished surface becoming more and more rugged as the pressure increased. In addition, the turning degree of u-p curve increased with the increase of coarse RDX content and particle size, and could be reduced by improving the structure compactness.展开更多
According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accur...According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.展开更多
Reduction of Cr(VI)using zero-valent iron(ZVI)could not only decrease the amounts of chemicals used for reduction,but also decrease the discharge of sludge.In order to find a desirable ZVI material,reduction of Cr(VI)...Reduction of Cr(VI)using zero-valent iron(ZVI)could not only decrease the amounts of chemicals used for reduction,but also decrease the discharge of sludge.In order to find a desirable ZVI material,reduction of Cr(VI)with a relative high concentration using different kinds of ZVI powders(mainly carbon differences)including reduced Fe,grey cast iron,pig iron,nodular pig iron was carried out.Parameters such as ZVI dosage,type and size affecting on Cr(VI)reduction were firstly examined and grey cast iron was selected as a preferable reducing material,followed by pig iron.Additionally,it was found that the parameters had significant influences on experimental kinetics.Then,morphology and composition of the sample before and after reaction were characterized by SEM,EPMA and XPS analyses to disclose carbon effect on the reducibility.In order to further interpret reaction mechanism,different reaction models were constructed.It was revealed that not only the carbon content could affect the Cr(VI)reduction,but also the carbon structure had an important effect on its reduction.展开更多
The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 （CBS） glass ceramics were investigated by Fourier transform infrared spectroscopy （FTIR）, X-ray diff...The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 （CBS） glass ceramics were investigated by Fourier transform infrared spectroscopy （FTIR）, X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. The results show that the increasing amount of B203 causes the increase of the contents of [BO3], [BO4] and [SiO4], which deduces the increase of CaB204 and a-SiO2 and the decrease of CaSiO3 correspondingly. No new phase is observed throughout the entire experiments. A bulk density of 2.54 g/cm3, a thermal expansion coefficient value of 11.95× 10-6 ℃-1 （20-500℃）, a dielectric constant er value of 6.42 and a dielectric loss tanδ value of 0.000 9 （measured at 9.7 GHz） are obtained for CBS glass ceramics containing 35%-B203 （mass fraction） sintered at 850 ℃ for 15 min.展开更多
On the basis of previous studies dealing with the variation of major agronomic and yield characteristics of regenerated plants derived from single cell culture in vitro of common wheat (Triticum aestivum L.Cult...On the basis of previous studies dealing with the variation of major agronomic and yield characteristics of regenerated plants derived from single cell culture in vitro of common wheat (Triticum aestivum L.Cultivar NE 7742), the grain protein content and its fractions from regenerated plants with stable agronomic characteristics were studied from 1992 to 1995. The results showed that the variation of grain protein content and its fractions in somaclones from single cell culture in vitro were very significant and the range was very wide (11531770%). Several types of variation were found in the studies, especially the type with higher protein content than that of cultivar NE 7742 (non-culture parent). Among them, -2069% of lines the grain protein content was significantly higher than that of NE 7742 and combined with high yielding potential. The tendency of variation of the four protein fractions showed that the variation of albumin was not obvious and maintained the same level as NE774 increased in some somaclones and decreased in others. However, the percentages both globulin and glutenin tended to increase. The variation of total amount of structural protein and the ratio between globulin and glutenin tended to increase. The variation of total amount of structural protein and the ratio between globulin and albumm was mainly influenced by globulin under the condition of culture in vitro. The variation of total amount of storage protein and the ratio between gliadin and glutenin was mainly affected by glutenin. The results mentioned above demonstrated that the induction and screening of somaclonal variation could be an effective way in wheat improvement in combining high protein content with high yield.展开更多
The improved granular mixtures are widely used as the fillings of railway 8ubgrade, and in order to investigate the effect of coarse grain content on granular mixtures, a series of field tests were conducted. The expe...The improved granular mixtures are widely used as the fillings of railway 8ubgrade, and in order to investigate the effect of coarse grain content on granular mixtures, a series of field tests were conducted. The experimental results indicate that the permeability coefficient increases significantly with the increment of granite gravel content, especially in the range of 60%-70%. Thcrc exists a coarse grain content limit defined as 53%-58.5% to reform the permeable granular skeleton. Beyond this limit, the permeable granular skeleton is efficiently formed, and the macro pores between the separate gravels are partially filled, which is the explanation lbr the permeability increase. The investigations indicate the subgrade resistance modulus （ks0, Ev2, and Evd） depends on the granite gravel content, and the resistance modulus increases significantly beyond granite gravel content of 50%. The skeletons of granitc gravel clayey sand mixture change in the long-term deformation objected to the train-induced dynamic load, which involves three main repeated and circular deformation stages. Generally, the long-time deformation is explained as the gravel crushing and filling the internal porous space with crushed gravel fragments. Through these investigations, the C40-G60 or C30-G70 is recommended as an optimum soil mixture for the good permeability and high resistance modulus.展开更多
Surface tension of calcium aluminate refining slag was measured by the Slide method at 1823 K.Based on different levels of the MgO content and the mass ratio of CaO to Al_2O_3,the effects of MgO content and the mass r...Surface tension of calcium aluminate refining slag was measured by the Slide method at 1823 K.Based on different levels of the MgO content and the mass ratio of CaO to Al_2O_3,the effects of MgO content and the mass ratio of CaO to Al_2O_3 on surface tension were investigated.The results indicate that surface tension decreased with increasing MgO content(from 0 to 4.86%),followed by an increase with further increasing MgO content up to 11.33%.The trend that surface tension changed with the mass ratio of CaO to Al_2O_3 was the same as the trend that surface tension changed with the MgO content.The surface tension was varied from 0.617 N/m to 0.710 N/m,for the mass ratio of CaO to Al_2O_3 varying between 0.60 and 1.28.An attempt was made to estimate surface tension of CaO-Al_2O_3-MgO slag and its sub-system,and the application showed that the model worked well.展开更多
文摘Backoff mechanism is a key component of contention-based medium access control（MAC） layer protocol.It has been shown that the backoff mechanism of IEEE 802.11 standard may be very inefficient especially when the network is congested.Numbers of methods have been proposed to tune the contention window（CW） with the aim to achieve the optimal throughput in IEEE 802.11 WLANs.However,the mechanisms do not specifically address proper settings for the variable packet length influence and CW diverging problem.This paper proposes a novel four-way handshaking full-feedback backoff algorithm named adoptive contention window backoff（ACWB） to overcome these drawbacks.The performance of the proposed algorithm is investigated through analysis and simulation.Simulation results demonstrate that the ACWB algorithm provides a remarkable performance improvement in terms of short-term fairness,packet delay and delay jitter,while maintaining an optimal throughput close to the theoretical throughput limit of the IEEE 802.11 distributed coordination function（DCF） access scheme.
文摘Aseries of [(Fe_(0.6)Co_(0.2)Ni_(0.2))_(0.75-0.03x)B_(0.2)Si_(0.05+0.03x)]_(96)Nb_(4) amorphous alloy composite coatings were prepared by adjusting the silicon content(x=0,1,2,3,4,5,and 6)and their microstructures and tribological properties were investigated by laser cladding technique.Additionally,the effect of Si on the glass forming ability(GFA)of the layers was understood.Results show that an appropriate Si content can refine the microstructure of the FeCoNiBSiNb laser cladding layers and improve the mechanical and tribological properties.The hardness of the coating layer increases monotonically with the Si content.At the Si content of 4.8at%(x=0),the coating layer exhibits a relatively low hardness(734.2HV 0.1).Conversely,at the silicon content of 13.44at%(x=3),the coating layer exhibits the highest hardness(1106HV 0.1).The non-crystalline content and tensile strength exhibit an initial increase,followed by a subsequent decrease.At x=2,the coating exhibits its maximum fracture strength(2880 MPa).However,when x>2,the fracture strength of the coating decreases with an increase in x.Conversely,with an increase in Si content,the wear volume loss initially decreases and then increases.At a Si content of 10.56at%(x=2),the coating exhibits the highest non-crystalline content(42%),the highest tensile strength(2880 MPa),and the most favorable dry friction performance.
基金Projects(52174096, 52304110) supported by the National Natural Science Foundation of China。
文摘Water is a critical factor affecting the mechanical properties of rocks, leading to their degradation. Understanding the creep mechanical behavior of deep roadway surrounding rock under the influence of underground water is of great significance. Compression and creep experiments on sandstone with varying water contents were conducted using a deep soft rock five-linked rheological experiment system. The experimental conditions, including water content (0%, 0.8%, 1.6%, 2.4% and 3.3%) and confining pressure (0, 6, 9 and 12 MPa), were determined based on pressure-free water absorption tests and in-situ stress measurements. The experimental results show that the compressive strength, creep failure stress, and dilatancy stress of sandstone decrease exponentially with increasing water content, while they increase exponentially with confining pressure. The ratio of lateral to axial instantaneous strain increases nearly linearly with the increase of stress, and the lateral creep strain characteristics of the sample are more significant than the axial ones. The duration of the attenuation creep stage of sandstone decreases with increasing water content and increases with increasing confining pressure. The lateral strain enters the steady-state creep stage before the axial strain, and the onset time of the accelerated creep stage of lateral strain under the failure stress is earlier than that of axial strain. The long-term strength of sandstone was determined based on the lateral steady-state creep rate curve, showing a negative exponential relationship with water content and a positive exponential relationship with confining pressure. A method for determining the long-term strength of rocks based on the ratio of lateral strain to axial strain (μc) is proposed, which is independent of water content. The research results provide a reliable theoretical basis for the analysis of the long-term stability of roadways under the influence of groundwater and the early prediction of creep failure.
基金Project(2002CB412704) supported by the Major State Basic Research Development Program of China
文摘In order to analyze mechanism of casing damage,the uniaxial compression experiment and creep experiment of interbedded mudstone samples from Sanan development area of Daqing Oilfield under different water contents were carried out.The changes of the mudstone's mechanical parameters and creep characteristics with the increment of water saturation were studied.The results indicate that the rock strength and elastic modulus decrease rapidly with the increment of water content,at the same time,the creep strain and creep strain rate of steady state increase with the increment of water content,and also the steady state creep strain rate is enhanced with the increment of deviatoric stress.Through the creep characteristic curves,a non-linear creep constitutive equation of mudstone considering the change of water contents is established,which will be used in future numerical analysis.
基金Tenth Five-year Plan of the Committee of the Science and Technology of Heilongjiang Province (GB02B4040-1)Item of Heilongjiang Education Bureau (10511012)
文摘An experiment about rice milling was made to study on the relationship between the different moisture content of brown rice and the energy consumption, the broken rice rate, the crack rate and the head rice yield. It could be concluded that the head rice yield increased at first falls and then along with the raise of moisture content and it could reach the maximum 70.78% when moisture content was 15.5%; the energy consumption of rice milling decreased along with the increase of moisture contents; the broken rice rate fell at first and then increased along with the raise of moisture contents and it could reach the minimum 4.28% when the moisture content was 15.5%.
文摘Employing the pot experiment of the complete random block design with 6 replications,four varieties of japonica rice (Fujisaka 5,Honenwase,Akitakomachi and Taichung 65) were used to study the varietal differences in leaf nitrogen content(LNC) and leaf area during mature period,their relation and effects to the ripening rate.The results showed that(1) thee were varietal differences in LNC at the heading stage and the LNC decrease rate during the matue period,the high LNC at the heading stage was related to the rapid LNC decrease.(2) There were two phases of the leaf area changing process during the mature period,first was the stable,and second was the decreased phase.There was varietal difference in the critical time of phase 1 and phase 2.The hign leaf area in the phase 1 was in relation to the rapid leaf area decrease in the phase 2.It was not found that there was relation between the leaf quality and quantity.(3)It wa unfavorable to the ripening rate for the high leaf area at the heading stage and the rapid decrease of the leaf area during the mature period.(4)It was put forward that the super high yield rice variety should possess the not very high leaf area and high LNC at the heading stage,slow senescence in the leaf area during the mature period.
基金This project was supported by the Digital TV Special Foundation of National Development and Reform Commission ofChina (040313) Home Coming Scholars Science Activity Foundation of Ministry of Personnel (20041231) the Graduate In-novation Foundation of Xidian University (innovaion 0509)
文摘A novel copyright protection scheme for digital content is presented, which is a private watermarking scheme based on the watermark embedding in the DCT domain and watermark extraction Using independent component analysis （ICA）. The system includes the key for watermark extraction and the host image. The algorithm splits the original image into blocks and classifies these blocks based on visual masking, that is, noise visibility function （NVF）. Watermark components with different strength are inserted into chosen direct current components of DCT coefficients according to the classifier. The watermark extraction is based on the characteristic of the statistic independence of the host image, watermark and key. Principle component analysis （PCA） whitening process and FastICA techniques are introduced to ensure a blind watermark extraction without requiring the original image. Experirnental results show the proposed technique is robust under attacks such as image filtering and adding noise, cropping and resizing. In addition, the proposed private watermarking system can be improved to the application of the DTV content protection system.
基金Supported by the 11th Five Year Plan of Rapessed Program in Guizhou Province, Scientific Contract of Guizhou N2 No.(2005) 3006-02-03
文摘Nine inbred lines of rapeseed （Brassica napus L.） used as male were crossed to five recessive genetic male sterile （RGMS） lines used as female to produce 45 single crosses. The crosses, their parents and a check hybrid were tested at two locations during 2007 to 2008 for testing the performance and heterosis of hybrids for seed yield and other characters. Results showed that variations for seed yield, oil content, days to flowering and days to maturity were significant. Mean squares for hybrids were significant for all characters. High heterosis （-4.5%-88.3%）, heterobeltiosis （-15.6%-81.1%） and standard heterosis G34.8%-33.1%） were found for the seed yield. The highest heterosis and heterobeltiosis were found in the cross QH303-4A× 1190. The highest standard heterosis was found in the cross Qianyou8A×Q034. Both positive and negative heterosis of single crosses were detected for the oil content. Small heterosis was found for days to flowering and days to maturity. Among parents, Ⅲ 188, Ⅲ224, and Q034 were proved to be the superior for seed yield when used as parents in most of the hybrid combinations. 2365, Ⅲ224, and QH303-4AB were good for high oil content breeding, Ⅲ 176, 2313 and Qianyou3AB were good for the early hybrid breeding. Total 11 hybrids yielded higher than 2 500 kg·hm^-2 and also gave significantly positive heterosis, heterobeltiosis and standard heterosis. Among them, 10 crosses gave higher oil content than that of check. These crosses can be used in the future breeding program for the seed yield and the oil content. Two crosses including Qianyou3A × Ⅲ224 and Qianyou3A×2313 can be used for the early breeding program.
文摘Well-sintered polycrystalline cubic boron nitride(PCBN)composites with different contents of cubic boron nitride(CBN) were obtained using Al and TiN as additives under pressure of 5.5 GPa and temperature of 1450 ℃.The network structure of CBN grains and bonding materials was observed using scanning electron microscope(SEM).With the help of X-ray diffraction(XRD) analysis,TiB2 and AlN could be determined as main products and Al3 Ti also was detected in the Al-rich samples after sintering process.Furthermore,it was shown that Vickers hardness of composites was improved with the increase of CBN contents.However,the lifetime of PCBN composites was in negative correlation with the amount of CBN in turning GCr15 hardened steels,and the surface roughness of workpieces machined by these PCBN composites also showed the same trend.A series of cutting data confirmed that the low CBN content in PCBN composites could enhance the working durability and improve the surface quality in turning hardened steels.The present experiments also indicated that the lowest value of flank wear was not constant for different PCBN composites when they were used to machine several workpieces with different hardness.
基金Project(11JJ2031)supported by the Key Project of Natural Fund of Hunan Province,ChinaProject(2009SK3029)supported by the Plan of Hunan Provincial Science and Technology Department,China
文摘The effect of sulfur addition/solids content(SA/SC)ratio on heavy metals(e.g.copper,zinc and lead)obtained from mine tailings by indigenous sulfur-oxidizing bacteria was studied,and the changes in the chemical forms of heavy metals after bioleaching were explored.The results show that the solubilization of metals is significantly influenced by SA/SC ratio,and SA/SC ratio of 2.50 is found to be the best for bacterial activity and metal solubilization among six SA/SC ratios tested(such as 1.00,1.33,1.50,1.67,2.00 and 2.50)under the chosen experimental conditions.The pH decreases fast and the maximum solubilizations of copper and zinc are respectively 81.76% and 84.35% while that of lead only reaches 40.36%.After bioleaching,the chemical forms of heavy metals have changed.The metals remained in mine tailings are mainly found in residual fractions,which is harmless to the surrounding environment.
文摘Visible and near-infrared(VNIR)spectroscopy is an eco-friendly method used for estimating plant nutrient deficiencies.The aim of this study was to investigate the possibility of using VNIR method for estimating Zn content in cherry orchard leaves under field conditions.The study was conducted in 3different locations in Isparta region of Turkey.Fifteen cherry orchards containing normal and Zn deficient plants were chosen,and 60 leaf samples were collected from each location.The reflectance spectra of the leaves were measured with an ASD FieldSpec HandHeld spectroradiometer and a plant probe.The Zn contents of leaf samples were predicted through laboratory analysis.The spectral reflectance measurements were used to estimate the Zn levels using stepwise multiple linear regression analysis method.Prediction models were created using the highest coefficient of determination value.The results show that Zn content of cherry trees can be estimated using the VNIR spectroscopic method(87.5<r2<96.79).Moreover,plant nutrient contents can be estimated without using chemicals.However,further research is necessary to develop a standard method for field conditions.Because spectral reflectance is affected by ecological conditions,agricultural applications and nutrient interactions,more effective models must be developed depending on the geographical location,period and plant type.
基金the support of Key Laboratory of Special Energy Materials,Ministry of Education,Nanjing,210094,China.
文摘Particle size and content of RDX are the two main factors that affect the burning stability of RDX-based propellants. However, these effects and the corresponding mechanisms are still controversial. In this work, we investigated the physicochemical processes during burning and the corresponding mechanisms through the technologies of structure compactness analysis on the base of voidage measurement and theoretical interfacial area estimation, apparent burning rate measurement using closed vessel(CV)and extinguished burning surface characterization relying on interrupted closed vessel(ICV) and scanning electron microscope(SEM). The results indicate that the voidage increased with the increase of RDX content and particle size due to the increasing interfacial area and increasing interface gap size,respectively. The apparent burning rate increased with the increase of RDX particle size because of the decreasing RDX specific surface area on the burning surface, which could decrease the heat absorbing rates of the melting and evaporation processes of RDX in the condensed phase. Similarly, the apparent burning rate decreased with the increase of RDX content at pressures lower than around 55 MPa due to the increasing RDX specific surface area. Whereas, an opposite trend could be observed at pressures higher than around 55 MPa, which was attributed to the increasing heat feedback from the gas phase as the result of the increasing propellant energy. For propellants containing very coarse RDX particles, such as 97.8 and 199.4 μm average size, the apparent burning rate increased stably with a flat extinguished surface at pressures lower than around 30 MPa, while increased sharply above around 30 MPa with the extinguished surface becoming more and more rugged as the pressure increased. In addition, the turning degree of u-p curve increased with the increase of coarse RDX content and particle size, and could be reduced by improving the structure compactness.
基金Supported by the National Natural Science Foundation of China(51275145)
文摘According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.
基金Project(51604131)supported by the National Natural Science Foundation of ChinaProject(2017FB084)supported by the Yunnan Province Applied Basic Research,China+1 种基金Project(KKSY201563041)supported by the Talent&Training Program of Yunnan Province,ChinaProjects(2017T20090159,2018T20150055)supported by the Testing and Analyzing Funds of Kunming University of Science and Technology,China
文摘Reduction of Cr(VI)using zero-valent iron(ZVI)could not only decrease the amounts of chemicals used for reduction,but also decrease the discharge of sludge.In order to find a desirable ZVI material,reduction of Cr(VI)with a relative high concentration using different kinds of ZVI powders(mainly carbon differences)including reduced Fe,grey cast iron,pig iron,nodular pig iron was carried out.Parameters such as ZVI dosage,type and size affecting on Cr(VI)reduction were firstly examined and grey cast iron was selected as a preferable reducing material,followed by pig iron.Additionally,it was found that the parameters had significant influences on experimental kinetics.Then,morphology and composition of the sample before and after reaction were characterized by SEM,EPMA and XPS analyses to disclose carbon effect on the reducibility.In order to further interpret reaction mechanism,different reaction models were constructed.It was revealed that not only the carbon content could affect the Cr(VI)reduction,but also the carbon structure had an important effect on its reduction.
基金Project(2007AA03Z0455) supported by the National High-Technology Research and Development Program of ChinaProject(BE2009168) supported by the Natural Science Foundation of Jiangsu Province in ChinaProject supported by the Priority Academic Program Development of Jiangsu Higher Education Institution,China
文摘The effects of B2O3 addition on both the sintering behavior and microwave dielectric properties of CaO-B2O3-SiO2 （CBS） glass ceramics were investigated by Fourier transform infrared spectroscopy （FTIR）, X-ray diffractometry （XRD） and scanning electron microscopy （SEM）. The results show that the increasing amount of B203 causes the increase of the contents of [BO3], [BO4] and [SiO4], which deduces the increase of CaB204 and a-SiO2 and the decrease of CaSiO3 correspondingly. No new phase is observed throughout the entire experiments. A bulk density of 2.54 g/cm3, a thermal expansion coefficient value of 11.95× 10-6 ℃-1 （20-500℃）, a dielectric constant er value of 6.42 and a dielectric loss tanδ value of 0.000 9 （measured at 9.7 GHz） are obtained for CBS glass ceramics containing 35%-B203 （mass fraction） sintered at 850 ℃ for 15 min.
文摘On the basis of previous studies dealing with the variation of major agronomic and yield characteristics of regenerated plants derived from single cell culture in vitro of common wheat (Triticum aestivum L.Cultivar NE 7742), the grain protein content and its fractions from regenerated plants with stable agronomic characteristics were studied from 1992 to 1995. The results showed that the variation of grain protein content and its fractions in somaclones from single cell culture in vitro were very significant and the range was very wide (11531770%). Several types of variation were found in the studies, especially the type with higher protein content than that of cultivar NE 7742 (non-culture parent). Among them, -2069% of lines the grain protein content was significantly higher than that of NE 7742 and combined with high yielding potential. The tendency of variation of the four protein fractions showed that the variation of albumin was not obvious and maintained the same level as NE774 increased in some somaclones and decreased in others. However, the percentages both globulin and glutenin tended to increase. The variation of total amount of structural protein and the ratio between globulin and glutenin tended to increase. The variation of total amount of structural protein and the ratio between globulin and albumm was mainly influenced by globulin under the condition of culture in vitro. The variation of total amount of storage protein and the ratio between gliadin and glutenin was mainly affected by glutenin. The results mentioned above demonstrated that the induction and screening of somaclonal variation could be an effective way in wheat improvement in combining high protein content with high yield.
基金Project(51378514)supported by the National Natural Science Foundation of China
文摘The improved granular mixtures are widely used as the fillings of railway 8ubgrade, and in order to investigate the effect of coarse grain content on granular mixtures, a series of field tests were conducted. The experimental results indicate that the permeability coefficient increases significantly with the increment of granite gravel content, especially in the range of 60%-70%. Thcrc exists a coarse grain content limit defined as 53%-58.5% to reform the permeable granular skeleton. Beyond this limit, the permeable granular skeleton is efficiently formed, and the macro pores between the separate gravels are partially filled, which is the explanation lbr the permeability increase. The investigations indicate the subgrade resistance modulus （ks0, Ev2, and Evd） depends on the granite gravel content, and the resistance modulus increases significantly beyond granite gravel content of 50%. The skeletons of granitc gravel clayey sand mixture change in the long-term deformation objected to the train-induced dynamic load, which involves three main repeated and circular deformation stages. Generally, the long-time deformation is explained as the gravel crushing and filling the internal porous space with crushed gravel fragments. Through these investigations, the C40-G60 or C30-G70 is recommended as an optimum soil mixture for the good permeability and high resistance modulus.
基金Project(51204115)supported by the National Natural Science Foundation of ChinaProject(BK20130308)supported by the Basic Research Program of Jiangsu Province,ChinaProject(2014M561710)supported by China Postdoctoral Science Foundation
文摘Surface tension of calcium aluminate refining slag was measured by the Slide method at 1823 K.Based on different levels of the MgO content and the mass ratio of CaO to Al_2O_3,the effects of MgO content and the mass ratio of CaO to Al_2O_3 on surface tension were investigated.The results indicate that surface tension decreased with increasing MgO content(from 0 to 4.86%),followed by an increase with further increasing MgO content up to 11.33%.The trend that surface tension changed with the mass ratio of CaO to Al_2O_3 was the same as the trend that surface tension changed with the MgO content.The surface tension was varied from 0.617 N/m to 0.710 N/m,for the mass ratio of CaO to Al_2O_3 varying between 0.60 and 1.28.An attempt was made to estimate surface tension of CaO-Al_2O_3-MgO slag and its sub-system,and the application showed that the model worked well.
