This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standar...This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standard system was established for comprehensive quality evaluation of HTD.There were obvious changes in the physicochemical properties,enzyme activities,and volatile flavor components at different storage periods,which affected the sensory evaluation of HTD to a certain extent.The results of high-throughput sequencing revealed significant microbial diversity,and showed that the bacterial community changed significantly more than did the fungal community.During the storage process,the dominant bacterial genera were Kroppenstedtia and Thermoascus.The correlation between dominant microorganisms and quality indicators highlighted their role in HTD quality.Lactococcus,Candida,Pichia,Paecilomyces,and protease activity played a crucial role in the formation of isovaleraldehyde.Acidic protease activity had the greatest impact on the microbial community.Moisture promoted isobutyric acid generation.Furthermore,the comprehensive quality evaluation standard system was established by the entropy weight method combined with multi-factor fuzzy mathematics.Consequently,this study provides innovative insights for comprehensive quality evaluation of HTD during storage and establishes a groundwork for scientific and rational storage of HTD and quality control of sauce-flavor Baijiu.展开更多
High-temperature piezoelectric sen-sors are very important in severe environments such as fire safety,aerospace and oil drills,however,most current sensors are not heat res-istant(<300℃)and are fragile,which limit...High-temperature piezoelectric sen-sors are very important in severe environments such as fire safety,aerospace and oil drills,however,most current sensors are not heat res-istant(<300℃)and are fragile,which limits their use,especially in high-temperature environ-ments.A high-temperature resistant flexible piezoelectric film based on graphene oxide(GO)/polyacrylonitrile(PAN)composites was prepared by electrospinning and thermal treat-ment.It was packed into a micro-device,which could work continuously at 500℃.The intro-duction of GO significantly increased the mechanical properties of the PAN nanofibers because the oxygen-containing func-tional groups(electronegative groups)on the surface of the GO initiated a nucleophilic attack on the PAN molecule during heat treatment,enabling the GO to initiate the cyclization of the PAN at lower heat-treatment temperatures.In addition,the abund-ant oxygen-containing functional groups on GO acted as pro-oxidants to hasten the oxidation of PAN during heat treatment.The effects of GO content and heat treatment temperature on the properties of the nanofiber films were investigated.A GO/PAN nanofiber piezoelectric sensor heat-treated at 300℃had a 9.10 V and 2.25μA peak output,which are respectively 101.3%and 78.6%higher than those of the untreated films.Cyclic testing over 5000 cycles at 350℃confirmed the stable out-put performance of the GO/PAN nanofiber piezoelectric sensor.Furthermore,a sensor heat-treated at 400℃had a sensitivity of 1.7 V/N,which is 83.5%higher than that of an untreated one.The results show that the prepared GO/PAN nanofiber piezo-electric sensor combines high temperature resistance,high flexibility,stability and high sensitivity,and may have broad applic-ations in high temperature environments such as the aerospace and petroleum industries.展开更多
To investigate the influence of temperature on the physical,mechanical and acoustic emission characteristics of granites,uniaxial compression test,variable-angle shear test,acoustic emission signal monitoring and the ...To investigate the influence of temperature on the physical,mechanical and acoustic emission characteristics of granites,uniaxial compression test,variable-angle shear test,acoustic emission signal monitoring and the measurement of physical parameters including mass,size and P-wave velocity were carried out on granite samples treated at temperatures T ranging from 25 to 900℃.The results show that the density and P-wave velocity decrease gradually with increasing T.As the temperature increases,the peak compressive stress decreases while the peak strain increases,due to the fact that a high temperature induces the escaping of waters within granites,the expanding of mineral grains and the generations of fractures.With the increment of T,both the peak shear stress and the cohesion decrease,whereas the frictional angle increases.During the compressing and shearing tests,the maximum acoustic emission counts show a decreasing trend when T increases from 25 to 900℃.When T exceeds 573℃,the crystal lattice structure of quartz changes fromα-phase toβ-phase,decreasing the mechanical behavior of granites to a great extent.In addition,the results also indicate that T=500−600℃ is the critical temperature ramge to characterize the influence of temperature on the physical,mechanical and acoustic emission characteristics of granites.展开更多
Two new binary near-azeotropic mixtures named M1 and M2 were developed as the refrigerants of the high-temperature heat pump(HTHP).The experimental research was used to analyze and compare the performance of M1 and M2...Two new binary near-azeotropic mixtures named M1 and M2 were developed as the refrigerants of the high-temperature heat pump(HTHP).The experimental research was used to analyze and compare the performance of M1 and M2-based in the HTHP in different running conditions.The results demonstrated the feasibility and reliability of M1 and M2 as new high-temperature refrigerants.Additionally,the exploration and analyses of the support vector machine(SVM)and back propagation(BP)neural network models were made to find a practical way to predict the performance of HTHP system.The results showed that SVM-Linear,SVM-RBF and BP models shared the similar ability to predict the heat capacity and power input with high accuracy.SVM-RBF demonstrated better stability for coefficient of performance prediction.Finally,the proposed SVM model was used to assess the potential of the M1 and M2.The results indicated that the HTHP system using M1 could produce heat at the temperature of 130°C with good performance.展开更多
To understand the response characteristics of soybean seedling resistance systems to high-temperature stress,the spring soybean varieties HN44 and HN65 were selected in this study as the experimental materials,as they...To understand the response characteristics of soybean seedling resistance systems to high-temperature stress,the spring soybean varieties HN44 and HN65 were selected in this study as the experimental materials,as they had substantial differences in stress resistance.Soybean physiological status was studied under high-temperature stress.Sand culture was used in the experiment,and soybeans at the seedling stage were treated with high-temperature stress.The results showed that the activity of antioxidases and osmotic regulatory substance contents in soybean increased under high-temperature treatment for a certain period of time,the activity of antioxidases and osmotic regulatory substance contents decreased after continuous treatment,and high temperatures continuously increased malondialdehyde contents in the two varieties.At high temperatures,the antioxidant activity and osmotic regulator contents of HN44 were higher than those of HN65,and the malondialdehyde contents of HN44 were higher than those of HN65.The above results showed that HN44 soybeans exhibited significantly higher resistance to high-temperature stress than HN65 variety.展开更多
Soil cement bentonite(SCB)is a common material for constructing vertical cutoff walls to prevent groundwater migration at contaminated industrial sites.However,site contaminants can degrade the durability of the cutof...Soil cement bentonite(SCB)is a common material for constructing vertical cutoff walls to prevent groundwater migration at contaminated industrial sites.However,site contaminants can degrade the durability of the cutoff wall.To enhance its performance,this study developed a silica fume-SCB(SSCB).The macroscopic and microscopic properties of SSCB were assessed by unconfined compressive strength test,variable head permeability test,X-ray diffraction(XRD),scanning electron microscopy(SEM)and nuclear magnetic resonance(NMR)spectroscopy.The correlation between its multi-scale properties was analyzed based on pore characteristics.The results indicate that increasing the silica fume substitution ratio improved SSCB strength,especially in the middle and late curing stages.Moreover,increasing the substitution ratio decreased SSCB permeability coefficient,with a more pronounced effect in earlier curing stages.Silica fume addition also refined SSCB pore structure and reduced its porosity.The fractal dimension was used to quantify SSCB pore structure complexity.Increasing silica fume content reduced small pore fractal dimension in SSCB.Concurrently,SSCB strength increased and SSCB permeability coefficient decreased.The findings of this research will demonstrate the great potential of SSCB backfill for practical applications.展开更多
Die wall lubrication was applied on warm compaction powder metallurgy in hope to reduce the concentration level of the admixed lubricant since lubricant is harmful to the mechanical property of the sintered materials....Die wall lubrication was applied on warm compaction powder metallurgy in hope to reduce the concentration level of the admixed lubricant since lubricant is harmful to the mechanical property of the sintered materials. Iron-based samples were prepared by die wall lubricated warm compaction at 135 ℃ and 175 ℃, using polytetrafluoroethylene (PTFE) emulsion as die wall lubricant. A compacting pressure of 700 MPa and 550 MPa were used. The admixed lubricant concentration ranging from 0 to 0.6 wt.% was used in this study. Compared with non-die wall lubricated samples, the die wall lubricated samples have higher green densities. Results show that in addition to the decrease in ejection forces, green density of the compacts increased linearly with the decrease in admixed lubricant content. Mechanical property of the sintered compacts increase sharply when the admixed lubricant concentration reduced to 0.125 wt.% or less. Ejection force data indicated that samples with die wall lubrication show lower ejection forces when compared with samples without die wall lubrication. No scoring was observed in all experiments even for samples contain no admixed lubricant. Our results indicated that under experimental condition used in this study, no matter at which compaction pressure, compaction temperature, graphite and lubricant contents in the powder the die wall lubricated warm compaction would give the highest green density and lowest ejection force. It can be concluded that combination of die wall lubrication and warm compaction can provide P/M products with higher density and better quality. It is a feasible way to produce high performance P/M parts if suitable die wall lubrication system was applied.展开更多
In many fields of high-tech industry the ultra-t hi n wall parts are employed. In this paper the experiments were carried out to dis cuss the surface microstructure of the camera’s guided drawtube by applying ult ras...In many fields of high-tech industry the ultra-t hi n wall parts are employed. In this paper the experiments were carried out to dis cuss the surface microstructure of the camera’s guided drawtube by applying ult rasonic vibration cutting device to the traditional lathe. The influence rule of the cutting condition on the surface roughness was put forward, which was drawn by comparing the ultrasonic cutting with the common cutting by use of the cemen ted carbide tool and the polycrystalline diamond (PCD) tool. The test results sh owed that the ultrasonic cutting performs better than the common cutting in the same condition. According to the test results analyzing, the surface characteriz ation is influenced clearly by the rigidity of the acoustic system and the machi ne tool, as well the setting height of the tool tip. Otherwise, the dense regula r low frequency vibration ripples will be scraped on the machined surface. When the tool tip is set higher than the rotating center of the work piece by three t imes of the amplitude of ultrasonic vibration, the vibration ripples behave alig ht; they turn light and shade alternatively when the tool tip is lower than the rotating center of the work piece by three times of the amplitude of ultrasonic vibration. According to the test result analyzing, the following conclusions are put forward: 1) The surface roughness in ultrasonic cutting is better than that in common cutting. Under a one third critical cutting velocity, the value of th e surface roughness in ultrasonic cutting rise slightly along with the cutting v elocity, while in common cutting it decreases contrast to the cutting velocity; the curves of the surface roughness in ultrasonic cutting and common cutting see m to be alike, both increase along with the feed rate and the cutting depth, but the value in ultrasonic cutting is smaller in the same condition.2) The influen ce of the coolant on the surface roughness cannot be ignored. The kerosene can b e employed to improve the surface roughness in ultrasonic machining.3) In ultras onic cutting process of aluminum alloy ultra-thin wall work piece, the PCD tool performs better than the cemented carbide tools.4) The vibration ripples result from the not enough rigidity of the acoustic system and the improper setting he ight of the tool tip. The departure of the tool tip from the rotating center of the work piece to some extent causes the vibration ripples on the machined surfa ce.展开更多
A plane strain finite element model was established to investigate the effect of friction between diaphragm wall and soil on braced excavation. The behavior of interface between diaphragm wall and soil was simulated w...A plane strain finite element model was established to investigate the effect of friction between diaphragm wall and soil on braced excavation. The behavior of interface between diaphragm wall and soil was simulated with the interface model of ABAQUS. Parametric studies were conducted with different diaphragm wall external friction angles δ. The results show that deflection of diaphragm wall and ground surface settlement decrease with the decrease of δ. However, the reduction effect on diaphragm wall deflection is the most significant at the depth where the maximum wall deflection occurs and can be neglected at the wall base. The ratio between wall deep inward component and wall cantilever component reaches its peak value 2.7 when δ=5°. The ratio of the maximum ground surface settlement to the maximum wall lateral deflection decreases at a reduced rate with the increase of δ. For excavation with braced diaphragm wall, the effect of friction between diaphragm and soil on the deflection of diaphragm wall and ground settlement, especially the distribution of ground surface settlement behind diaphragm, should be taken into account.展开更多
In order to reduce the errors of the reliability of the retaining wall structure in the establishment of function, in the estimation of parameter and algorithm, firstly, two new reliability and stability models of ant...In order to reduce the errors of the reliability of the retaining wall structure in the establishment of function, in the estimation of parameter and algorithm, firstly, two new reliability and stability models of anti-slipping and anti-overturning based on the upper-bound theory of limit analysis were established, and two kinds of failure modes were regarded as a series of systems with multiple correlated failure modes. Then, statistical characteristics of parameters of the retaining wall structure were inferred by maximal entropy principle. At last, the structural reliabilities of single failure mode and multiple failure modes were calculated by Monte Carlo method in MATLAB and the results were compared and analyzed on the sensitivity. It indicates that this method, with a high precision, is not only easy to program and quick in calculation, but also without the limit of nonlinear functions and non-normal random variables. And the results calculated by this method which applies both the limit analysis theory, maximal entropy principle and Monte Carlo method into analyzing the reliability of the retaining wall structures is more scientific, accurate and reliable, in comparison with those calculated by traditional method.展开更多
Soil-bentonite （SB） vertical slurry cutoff wall is a useful treatment for urban industrial contaminated sites. Due to the clay-heavy metal interaction, significant changes would occur in the engineering behavior of ...Soil-bentonite （SB） vertical slurry cutoff wall is a useful treatment for urban industrial contaminated sites. Due to the clay-heavy metal interaction, significant changes would occur in the engineering behavior of SB cutoff walls. However, previous study is limited to kaolinitic soils or montmorillonitic soils along using solidum chloride and/or calcium chloride as target contaminant. In this work, a series of oedometer tests were conducted to investigate the effects of lead （Pb） on the compressibility and the permeability of kaolin-bentonite （KB） mixtures, a simplified model of in-situ SB cutoff wall backfills. In addition, sedimentation tests were conducted to interpret the mechanism controlling the change of compressibility and permeability from the perspective of soil fabric. The Pb-contaminated KB mixtures for oedometer tests and sedimentation tests were prepared with bentonite contents of 0, 5%, 10%, and 15% by dry mass, and they were mixed with pre-determined volume of lead nitrate solution based on designed Pb concentration and solid-to-solution ratio. The Pb concentration was controlled as 0, 0.1, 0.5, 1.0, 5.0, 10, and 50 mg/g with a solid-to-solution ratio of approximate 0.5. The prepared KB mixtures with bentonite contents of 0, 5%, and 10% were chosen for the sedimentation tests. They were freeze-dried and mixed with DDI with a solid-to-solution ratio of 10 g/100 mL. The results indicate that pH, compressibility, and permeability of KB mixture changed considerably with respect to Pb concentration. It is concluded that the fabric of KB mixture, depending on the particle-particle interaction subjected to different ranges of pH and Pb concentration, governs the sedimentation behavior and permeability. The results of liquid limit （WE） cannot be explained in terms of the sedimentation behavior since it is only ionic-dependent.展开更多
The aim of this study is to examine the effects of local curvature and elastic wall effects of an isothermal hot wall for the purpose of jet impingement cooling performance.Finite element method was used with ALE.Diff...The aim of this study is to examine the effects of local curvature and elastic wall effects of an isothermal hot wall for the purpose of jet impingement cooling performance.Finite element method was used with ALE.Different important parametric effects such as Re number(between 100 and 700),Ha number(between 0 and 20),elasticity(between 104 and 109),curvature of the surface(elliptic,radius ratio between 1 and 0.25) and nanoparticle volume fraction(between 0 and 0.05) on the cooling performance were investigated numerically.The results showed that the average Nu number enhances for higher Hartmann number,higher values of elastic modulus of partly flexible wall and higher nanoparticle volume fraction.When the magnetic field is imposed at the highest strength,there is an increase of3.85% in the average Nu for the curved elastic wall whereas it is 89.22% for the hot part above it,which is due to the vortex suppression effects.Nanoparticle inclusion in the base fluid improves the heat transfer rate by about 27.6% in the absence of magnetic field whereas it is 20.5% under the effects of magnetic field at Ha=20.Curvature effects become important for higher Re numbers and at Re=700,there is 14.11% variation in the average Nu between the cases with the lowest and highest radius ratio.The elastic wall effects on the heat transfer are reduced with the increased curvature of the bottom wall.展开更多
文摘This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standard system was established for comprehensive quality evaluation of HTD.There were obvious changes in the physicochemical properties,enzyme activities,and volatile flavor components at different storage periods,which affected the sensory evaluation of HTD to a certain extent.The results of high-throughput sequencing revealed significant microbial diversity,and showed that the bacterial community changed significantly more than did the fungal community.During the storage process,the dominant bacterial genera were Kroppenstedtia and Thermoascus.The correlation between dominant microorganisms and quality indicators highlighted their role in HTD quality.Lactococcus,Candida,Pichia,Paecilomyces,and protease activity played a crucial role in the formation of isovaleraldehyde.Acidic protease activity had the greatest impact on the microbial community.Moisture promoted isobutyric acid generation.Furthermore,the comprehensive quality evaluation standard system was established by the entropy weight method combined with multi-factor fuzzy mathematics.Consequently,this study provides innovative insights for comprehensive quality evaluation of HTD during storage and establishes a groundwork for scientific and rational storage of HTD and quality control of sauce-flavor Baijiu.
文摘High-temperature piezoelectric sen-sors are very important in severe environments such as fire safety,aerospace and oil drills,however,most current sensors are not heat res-istant(<300℃)and are fragile,which limits their use,especially in high-temperature environ-ments.A high-temperature resistant flexible piezoelectric film based on graphene oxide(GO)/polyacrylonitrile(PAN)composites was prepared by electrospinning and thermal treat-ment.It was packed into a micro-device,which could work continuously at 500℃.The intro-duction of GO significantly increased the mechanical properties of the PAN nanofibers because the oxygen-containing func-tional groups(electronegative groups)on the surface of the GO initiated a nucleophilic attack on the PAN molecule during heat treatment,enabling the GO to initiate the cyclization of the PAN at lower heat-treatment temperatures.In addition,the abund-ant oxygen-containing functional groups on GO acted as pro-oxidants to hasten the oxidation of PAN during heat treatment.The effects of GO content and heat treatment temperature on the properties of the nanofiber films were investigated.A GO/PAN nanofiber piezoelectric sensor heat-treated at 300℃had a 9.10 V and 2.25μA peak output,which are respectively 101.3%and 78.6%higher than those of the untreated films.Cyclic testing over 5000 cycles at 350℃confirmed the stable out-put performance of the GO/PAN nanofiber piezoelectric sensor.Furthermore,a sensor heat-treated at 400℃had a sensitivity of 1.7 V/N,which is 83.5%higher than that of an untreated one.The results show that the prepared GO/PAN nanofiber piezo-electric sensor combines high temperature resistance,high flexibility,stability and high sensitivity,and may have broad applic-ations in high temperature environments such as the aerospace and petroleum industries.
基金Projects(51979272,BZ2020066)supported by the National Natural Science Foundation of ChinaProjet supported by the Department of Science and Technology of Jiangsu Province,China。
文摘To investigate the influence of temperature on the physical,mechanical and acoustic emission characteristics of granites,uniaxial compression test,variable-angle shear test,acoustic emission signal monitoring and the measurement of physical parameters including mass,size and P-wave velocity were carried out on granite samples treated at temperatures T ranging from 25 to 900℃.The results show that the density and P-wave velocity decrease gradually with increasing T.As the temperature increases,the peak compressive stress decreases while the peak strain increases,due to the fact that a high temperature induces the escaping of waters within granites,the expanding of mineral grains and the generations of fractures.With the increment of T,both the peak shear stress and the cohesion decrease,whereas the frictional angle increases.During the compressing and shearing tests,the maximum acoustic emission counts show a decreasing trend when T increases from 25 to 900℃.When T exceeds 573℃,the crystal lattice structure of quartz changes fromα-phase toβ-phase,decreasing the mechanical behavior of granites to a great extent.In addition,the results also indicate that T=500−600℃ is the critical temperature ramge to characterize the influence of temperature on the physical,mechanical and acoustic emission characteristics of granites.
基金Project (2015CB251403) supported by the National Key Basic Research Program of China(973)
文摘Two new binary near-azeotropic mixtures named M1 and M2 were developed as the refrigerants of the high-temperature heat pump(HTHP).The experimental research was used to analyze and compare the performance of M1 and M2-based in the HTHP in different running conditions.The results demonstrated the feasibility and reliability of M1 and M2 as new high-temperature refrigerants.Additionally,the exploration and analyses of the support vector machine(SVM)and back propagation(BP)neural network models were made to find a practical way to predict the performance of HTHP system.The results showed that SVM-Linear,SVM-RBF and BP models shared the similar ability to predict the heat capacity and power input with high accuracy.SVM-RBF demonstrated better stability for coefficient of performance prediction.Finally,the proposed SVM model was used to assess the potential of the M1 and M2.The results indicated that the HTHP system using M1 could produce heat at the temperature of 130°C with good performance.
基金Supported by the National Key Research and Development Program(2018YFD1000903)。
文摘To understand the response characteristics of soybean seedling resistance systems to high-temperature stress,the spring soybean varieties HN44 and HN65 were selected in this study as the experimental materials,as they had substantial differences in stress resistance.Soybean physiological status was studied under high-temperature stress.Sand culture was used in the experiment,and soybeans at the seedling stage were treated with high-temperature stress.The results showed that the activity of antioxidases and osmotic regulatory substance contents in soybean increased under high-temperature treatment for a certain period of time,the activity of antioxidases and osmotic regulatory substance contents decreased after continuous treatment,and high temperatures continuously increased malondialdehyde contents in the two varieties.At high temperatures,the antioxidant activity and osmotic regulator contents of HN44 were higher than those of HN65,and the malondialdehyde contents of HN44 were higher than those of HN65.The above results showed that HN44 soybeans exhibited significantly higher resistance to high-temperature stress than HN65 variety.
基金Project(2019YFC1803601)supported by the National Key Research and Development Program of ChinaProject(52274182)supported by the National Natural Science Foundation of China+1 种基金Project(2021zzts0274)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(CX20210295)supported by the Postgraduate Scientific Research Innovation Project of Hunan Province,China。
文摘Soil cement bentonite(SCB)is a common material for constructing vertical cutoff walls to prevent groundwater migration at contaminated industrial sites.However,site contaminants can degrade the durability of the cutoff wall.To enhance its performance,this study developed a silica fume-SCB(SSCB).The macroscopic and microscopic properties of SSCB were assessed by unconfined compressive strength test,variable head permeability test,X-ray diffraction(XRD),scanning electron microscopy(SEM)and nuclear magnetic resonance(NMR)spectroscopy.The correlation between its multi-scale properties was analyzed based on pore characteristics.The results indicate that increasing the silica fume substitution ratio improved SSCB strength,especially in the middle and late curing stages.Moreover,increasing the substitution ratio decreased SSCB permeability coefficient,with a more pronounced effect in earlier curing stages.Silica fume addition also refined SSCB pore structure and reduced its porosity.The fractal dimension was used to quantify SSCB pore structure complexity.Increasing silica fume content reduced small pore fractal dimension in SSCB.Concurrently,SSCB strength increased and SSCB permeability coefficient decreased.The findings of this research will demonstrate the great potential of SSCB backfill for practical applications.
文摘Die wall lubrication was applied on warm compaction powder metallurgy in hope to reduce the concentration level of the admixed lubricant since lubricant is harmful to the mechanical property of the sintered materials. Iron-based samples were prepared by die wall lubricated warm compaction at 135 ℃ and 175 ℃, using polytetrafluoroethylene (PTFE) emulsion as die wall lubricant. A compacting pressure of 700 MPa and 550 MPa were used. The admixed lubricant concentration ranging from 0 to 0.6 wt.% was used in this study. Compared with non-die wall lubricated samples, the die wall lubricated samples have higher green densities. Results show that in addition to the decrease in ejection forces, green density of the compacts increased linearly with the decrease in admixed lubricant content. Mechanical property of the sintered compacts increase sharply when the admixed lubricant concentration reduced to 0.125 wt.% or less. Ejection force data indicated that samples with die wall lubrication show lower ejection forces when compared with samples without die wall lubrication. No scoring was observed in all experiments even for samples contain no admixed lubricant. Our results indicated that under experimental condition used in this study, no matter at which compaction pressure, compaction temperature, graphite and lubricant contents in the powder the die wall lubricated warm compaction would give the highest green density and lowest ejection force. It can be concluded that combination of die wall lubrication and warm compaction can provide P/M products with higher density and better quality. It is a feasible way to produce high performance P/M parts if suitable die wall lubrication system was applied.
文摘In many fields of high-tech industry the ultra-t hi n wall parts are employed. In this paper the experiments were carried out to dis cuss the surface microstructure of the camera’s guided drawtube by applying ult rasonic vibration cutting device to the traditional lathe. The influence rule of the cutting condition on the surface roughness was put forward, which was drawn by comparing the ultrasonic cutting with the common cutting by use of the cemen ted carbide tool and the polycrystalline diamond (PCD) tool. The test results sh owed that the ultrasonic cutting performs better than the common cutting in the same condition. According to the test results analyzing, the surface characteriz ation is influenced clearly by the rigidity of the acoustic system and the machi ne tool, as well the setting height of the tool tip. Otherwise, the dense regula r low frequency vibration ripples will be scraped on the machined surface. When the tool tip is set higher than the rotating center of the work piece by three t imes of the amplitude of ultrasonic vibration, the vibration ripples behave alig ht; they turn light and shade alternatively when the tool tip is lower than the rotating center of the work piece by three times of the amplitude of ultrasonic vibration. According to the test result analyzing, the following conclusions are put forward: 1) The surface roughness in ultrasonic cutting is better than that in common cutting. Under a one third critical cutting velocity, the value of th e surface roughness in ultrasonic cutting rise slightly along with the cutting v elocity, while in common cutting it decreases contrast to the cutting velocity; the curves of the surface roughness in ultrasonic cutting and common cutting see m to be alike, both increase along with the feed rate and the cutting depth, but the value in ultrasonic cutting is smaller in the same condition.2) The influen ce of the coolant on the surface roughness cannot be ignored. The kerosene can b e employed to improve the surface roughness in ultrasonic machining.3) In ultras onic cutting process of aluminum alloy ultra-thin wall work piece, the PCD tool performs better than the cemented carbide tools.4) The vibration ripples result from the not enough rigidity of the acoustic system and the improper setting he ight of the tool tip. The departure of the tool tip from the rotating center of the work piece to some extent causes the vibration ripples on the machined surfa ce.
基金Project (07FDZDSF01200) supported by Tianjin Science and Technology Innovation Special Funds
文摘A plane strain finite element model was established to investigate the effect of friction between diaphragm wall and soil on braced excavation. The behavior of interface between diaphragm wall and soil was simulated with the interface model of ABAQUS. Parametric studies were conducted with different diaphragm wall external friction angles δ. The results show that deflection of diaphragm wall and ground surface settlement decrease with the decrease of δ. However, the reduction effect on diaphragm wall deflection is the most significant at the depth where the maximum wall deflection occurs and can be neglected at the wall base. The ratio between wall deep inward component and wall cantilever component reaches its peak value 2.7 when δ=5°. The ratio of the maximum ground surface settlement to the maximum wall lateral deflection decreases at a reduced rate with the increase of δ. For excavation with braced diaphragm wall, the effect of friction between diaphragm and soil on the deflection of diaphragm wall and ground settlement, especially the distribution of ground surface settlement behind diaphragm, should be taken into account.
基金Project(2013CB036004) supported by the National Basic Research Program of ChinaProjects(51178468,51174086) supported by the National Natural Science Foundation of ChinaProject(201102) supported by the Open Foundation of Hunan Key Laboratory of Safe Mining Techniques of Coal Mines,China
文摘In order to reduce the errors of the reliability of the retaining wall structure in the establishment of function, in the estimation of parameter and algorithm, firstly, two new reliability and stability models of anti-slipping and anti-overturning based on the upper-bound theory of limit analysis were established, and two kinds of failure modes were regarded as a series of systems with multiple correlated failure modes. Then, statistical characteristics of parameters of the retaining wall structure were inferred by maximal entropy principle. At last, the structural reliabilities of single failure mode and multiple failure modes were calculated by Monte Carlo method in MATLAB and the results were compared and analyzed on the sensitivity. It indicates that this method, with a high precision, is not only easy to program and quick in calculation, but also without the limit of nonlinear functions and non-normal random variables. And the results calculated by this method which applies both the limit analysis theory, maximal entropy principle and Monte Carlo method into analyzing the reliability of the retaining wall structures is more scientific, accurate and reliable, in comparison with those calculated by traditional method.
基金Project(51278100) supported by the National Natural Science Foundation of ChinaProjects(BK2010060, BK2012022) supported by the Natural Science Foundation of Jiangsu Province, ChinaProject(103) supported by the Scientific Innovation Research of University Graduate Students of Jiangsu Province, China
文摘Soil-bentonite （SB） vertical slurry cutoff wall is a useful treatment for urban industrial contaminated sites. Due to the clay-heavy metal interaction, significant changes would occur in the engineering behavior of SB cutoff walls. However, previous study is limited to kaolinitic soils or montmorillonitic soils along using solidum chloride and/or calcium chloride as target contaminant. In this work, a series of oedometer tests were conducted to investigate the effects of lead （Pb） on the compressibility and the permeability of kaolin-bentonite （KB） mixtures, a simplified model of in-situ SB cutoff wall backfills. In addition, sedimentation tests were conducted to interpret the mechanism controlling the change of compressibility and permeability from the perspective of soil fabric. The Pb-contaminated KB mixtures for oedometer tests and sedimentation tests were prepared with bentonite contents of 0, 5%, 10%, and 15% by dry mass, and they were mixed with pre-determined volume of lead nitrate solution based on designed Pb concentration and solid-to-solution ratio. The Pb concentration was controlled as 0, 0.1, 0.5, 1.0, 5.0, 10, and 50 mg/g with a solid-to-solution ratio of approximate 0.5. The prepared KB mixtures with bentonite contents of 0, 5%, and 10% were chosen for the sedimentation tests. They were freeze-dried and mixed with DDI with a solid-to-solution ratio of 10 g/100 mL. The results indicate that pH, compressibility, and permeability of KB mixture changed considerably with respect to Pb concentration. It is concluded that the fabric of KB mixture, depending on the particle-particle interaction subjected to different ranges of pH and Pb concentration, governs the sedimentation behavior and permeability. The results of liquid limit （WE） cannot be explained in terms of the sedimentation behavior since it is only ionic-dependent.
文摘The aim of this study is to examine the effects of local curvature and elastic wall effects of an isothermal hot wall for the purpose of jet impingement cooling performance.Finite element method was used with ALE.Different important parametric effects such as Re number(between 100 and 700),Ha number(between 0 and 20),elasticity(between 104 and 109),curvature of the surface(elliptic,radius ratio between 1 and 0.25) and nanoparticle volume fraction(between 0 and 0.05) on the cooling performance were investigated numerically.The results showed that the average Nu number enhances for higher Hartmann number,higher values of elastic modulus of partly flexible wall and higher nanoparticle volume fraction.When the magnetic field is imposed at the highest strength,there is an increase of3.85% in the average Nu for the curved elastic wall whereas it is 89.22% for the hot part above it,which is due to the vortex suppression effects.Nanoparticle inclusion in the base fluid improves the heat transfer rate by about 27.6% in the absence of magnetic field whereas it is 20.5% under the effects of magnetic field at Ha=20.Curvature effects become important for higher Re numbers and at Re=700,there is 14.11% variation in the average Nu between the cases with the lowest and highest radius ratio.The elastic wall effects on the heat transfer are reduced with the increased curvature of the bottom wall.
