The ohmic contact interface between diamond and metal is essential for the application of diamond detectors.Surface modification can significantly affect the contact performance and eliminate the interface polarizatio...The ohmic contact interface between diamond and metal is essential for the application of diamond detectors.Surface modification can significantly affect the contact performance and eliminate the interface polarization effect.However,the radiation stability of a diamond detector is also sensitive to surface modification.In this work,the influence of surface modification technology on a diamond ohmic contact under high-energy radiation was investigated.Before radiation,the specific contact resistivities(ρc)between Ti/Pt/Au-hydrogen-terminated diamond(H-diamond)and Ti/Pt/Au-oxygenterminated diamond(O-diamond)were 2.0×10^(-4)W·cm^(2) and 4.3×10^(-3)Wcm^(2),respectively.After 10 MeV electron radiation,the ρc of Ti/Pt/Au H-diamond and Ti/Pt/Au O-diamond were 5.3×10^(-3)W·cm^(2)and 9.1×10^(-3)W·cm^(2),respectively.The rates of change of ρc of H-diamond and O-diamond after radiation were 2550%and 112%,respectively.The electron radiation promotes bond reconstruction of the diamond surface,resulting in an increase in ρc.展开更多
Nonalloyed ohmic contacts regrown by metal-organic chemical vapor deposition are performed on AlGaN/GaN high-electron-mobility transistors. Low ohmic contact resistance of 0.15Ω.mm is obtained. It is found that the s...Nonalloyed ohmic contacts regrown by metal-organic chemical vapor deposition are performed on AlGaN/GaN high-electron-mobility transistors. Low ohmic contact resistance of 0.15Ω.mm is obtained. It is found that the sidewall obliquity near the regrown interface induced by the plasma dry etching has great influence on the total contact resistance. The fabricated device with a 100-nm T-shaped gate demonstrates a maximum drain current density of 0.95 A/mm at Vgs = 1 V and a maximum peak extrinsic transcondutance Gm of 216mS/ram. Moreover, a current gain cut-off frequency fT of 115 GHz and a maximum oscillation frequency fmax of 127 GHz are achieved.展开更多
Contact electrification(CE)is a pretty common phenomenon,but still is poorly understood.The long-standing controversy over the mechanisms of CE related to polymers is particularly intense due to their complexity.In th...Contact electrification(CE)is a pretty common phenomenon,but still is poorly understood.The long-standing controversy over the mechanisms of CE related to polymers is particularly intense due to their complexity.In this paper,the CE between metals and polymers is systematically studied,which shows the evolution of surfaces is accompanied by variations of CE outputs.The variations of CE charge quantity are closely related to the creep and deformation of the polymer and metal surfaces.Then the relationship between CE and polymer structures is put forward,which is essentially determined by the electronegativity of elements and the functional groups in the polymers.The effects of load and contact frequency on the CE process and outputs are also investigated,indicating the increase of CE charge quantity with load and frequency.Material transfer from polymer to metal is observed during CE while electrons transfer from metal to polymer,both of which are believed to have an influence on each other.The findings advance our understanding of the mechanism of CE between metal and polymers,and provides insights into the performance of CE-based application in various conditions,which sheds light on the design and optimization of CE-based energy harvest and self-powered sensing devices.展开更多
Interactions between water and solid substrates are of fundamental importance to various processes in nature and industry.Electric control is widely used to modify interfacial water,where the influence of surface char...Interactions between water and solid substrates are of fundamental importance to various processes in nature and industry.Electric control is widely used to modify interfacial water,where the influence of surface charges is inevitable.Here we obtain positively and negatively charged surfaces using Li Ta O_(3) crystals and observe that a large net surface charge up to 0.1 C/m;can nominally change the contact angles of pure water droplets comparing to the same uncharged surface.However,even a small amount of surface charge can efficiently increase the water contact angle in the presence of aerosols.Our results indicate that such surface charges can hardly affect the structure of interfacial water molecular layers and the morphology of the macroscopic droplet,while adsorption of a small amount of organic contaminants from aerosols with the help of Coulomb attraction can notably decrease the wettability of solid surface.Our results not only provide a fundamental understanding of the interactions between charged surfaces and water,but also help to develop new techniques on electric control of wettability and microfluidics in real aerosol environments.展开更多
Traditional microstructure scale parameters have difficulty describing the structure and distribution of a roughmaterial’s surface morphology comprehensively and quantitatively. This study constructs hydrophilic and ...Traditional microstructure scale parameters have difficulty describing the structure and distribution of a roughmaterial’s surface morphology comprehensively and quantitatively. This study constructs hydrophilic and underwateroleophobic surfaces based on polyvinylidene fluoride (PVDF) using a chemical modification method, and the fractaldimension and multifractal spectrum are used to quantitatively characterize the microscopic morphology. A new contactangle prediction model for underwater oleophobic surfaces is established. The results show that the fractal dimension ofthe PVDF surface first increases and then decreases with the reaction time. The uniformity characterized by the multifractalspectrum was generally consistent with scanning electron microscope observations. The contact angle of water droplets onthe PVDF surface is negatively correlated with the fractal dimension, and oil droplets in water are positively correlated.When the fractal dimension is 2.0975, the new contact angle prediction model has higher prediction accuracy. Themaximum and minimum relative deviations of the contact angle between the theoretical and measured data are 18.20%and 0.72%, respectively. For water ring transportation, the larger the fractal dimension and spectral width of the materialsurface, the smaller the absolute value of the spectral difference, the stronger the hydrophilic and oleophobic properties, andthe better the water ring transportation stability.展开更多
Superhydrophobic aluminum surfaces have been prepared by means of electrodeposition of copper on aluminum surfaces, followed by electrochemical modification using stearic acid organic molecules. Scanning electron micr...Superhydrophobic aluminum surfaces have been prepared by means of electrodeposition of copper on aluminum surfaces, followed by electrochemical modification using stearic acid organic molecules. Scanning electron microscopy(SEM) images show that the electrodeposited copper films follow "island growth mode" in the form of microdots and their number densities increase with the rise of the negative deposition potentials. At an electrodeposition potential of-0.2 V the number density of the copper microdots are found to be 4.5×104cm^(-2)that are increased to 2.9×105cm^(-2)at a potential of-0.8 V. Systematically, the distances between the microdots are found to be reduced from 26.6 μm to 11.03 μm with the increase of negative electrochemical potential from-0.2 V to-0.8 V. X-ray diffraction(XRD) analyses have confirmed the formation of copper stearate on the stearic acid modified copper films. The roughness of the stearic acid modified electrodeposited copper films is found to increase with the increase in the density of the copper microdots. A critical copper deposition potential of-0.6 V in conjunction with the stearic acid modification provides a surface roughness of 6.2 μm with a water contact angle of 157?, resulting in superhydrophobic properties on the aluminum substrates.展开更多
Nanosecond-pulse diffuse discharges could provide high-density plasma and high-energy electrons at atmospheric pressure. In this paper, the surface treatment of Cu by nanosecond-pulse diffuse discharges is conducted i...Nanosecond-pulse diffuse discharges could provide high-density plasma and high-energy electrons at atmospheric pressure. In this paper, the surface treatment of Cu by nanosecond-pulse diffuse discharges is conducted in atmospheric air. Factors influencing the water contact angle （WCA）, chemical composition and microhardness, such as the gap spacing and treatment time, are investigated. The results show that after the plasma surface treatment, the WCA considerably decreases from 87~ to 42.3~, and the surface energy increases from 20.46 mJ m-2 to 66.28 mJ m-2. Results of energy dispersive x-ray analysis show that the concentration of carbon decreases, but the concentrations of oxygen and nitrogen increase significantly. Moreover, the microhardness increases by approximately 30% after the plasma treatment. The aforementioned changes on the Cu surface indicate the plasma surface treatment enhances the hydrophilicity and microhardness, and it cleans the carbon and achieves oxidization on the Cu surface. Furthermore, by increasing the gap spacing and treatment time, better treatment effects can be obtained. The micmhardness in the case of a 2.5 cm gap is higher than that in the case of a 3 cm gap. More oxygen and nitrogen species appear on the Cu surface for the 2.5 cm gap treatment than for the 3 cm gap treatment. The WCA significantly decreases with the treatment thne when it is no longer than 90 s, and then it reaches saturation. In addition, more oxygen-containing and nitrogen-containing groups appear after extended plasma treatment time. They contribute to the improvement of the hydrophilicity and oxidation on the Cu surface.展开更多
An atmospheric pressure plasma jet generated in Ar and O2/Ar mixtures has been investigated by specially designed equipment with double power electrodes at 20~32 kHz, and their effects on the cleaning of surfaces have...An atmospheric pressure plasma jet generated in Ar and O2/Ar mixtures has been investigated by specially designed equipment with double power electrodes at 20~32 kHz, and their effects on the cleaning of surfaces have been studied. Properties of the jet discharge are studied by electrical diagnostics, including the waveform of discharge voltage, discharge current and the Q-V Lissajous figures. The optical emission spectroscopy is used to measure the plasma parameters, such as the excitation temperature and the gas temperature. It is found that the consumed power and the excitation temperature increase with increase of the discharge frequency. On the other hand, at the same discharge frequency, these parameters in O2/Ar mixture plasma are found to be much larger. The effect on surface cleaning is studied from the changes in the contact angle. For Ar plasma jet, the contact angle decreases with increase of the discharge frequency. For O2/Ar mixture plasma jet, the contact angle decreases with increase of discharge frequency up to 26 kHz, however, further increase of discharge frequency does not show further decrease in the contact angle. At the same discharge frequency, the contact angle after O2/Ar mixture plasma cleaning is found to be much lower compared to the case of pure Ar. From the results of quadrupole mass-spectrum analysis, we can identify more fragment molecules of CO and H2O in the emitted gases after O2/Ar plasma jet treatment compared with Ar plasma jet treatment, which are produced by the decomposition of surface organic contaminants during the cleaning process.展开更多
In this study, the contact angles of three different reference liquids （including distilled water, diiodomethane, and formamide） and PF resin on the surfaces of Chinese fir （Cunningharnia lanceolata） samples untre...In this study, the contact angles of three different reference liquids （including distilled water, diiodomethane, and formamide） and PF resin on the surfaces of Chinese fir （Cunningharnia lanceolata） samples untreated or treated with different concentrations of ACQ-D （ammoniacal copper quat Type D） solutions were measured. Then, the surface free energy was calculated by two approaches： acid-base approach and geometric mean approach. ACQ-D treatment caused higher contact angles and lower surface free energies at a retention level corresponding to the commodity treated wood products. When wood was treated with much higher concentrations of ACQ-D, the total surface free energy of wood would be higher than the untreated control. Acid-base/polar components related with the hydrogen bonding state in wood were considered to be responsible for the observed changes according to the applied approaches. The hydrophobic properties and also higher contact angles of PF resin drop on wood surfaces after ACQ-D treatment at a reasonable retention level confirms the changes on surface free energy.展开更多
An atmospheric pressure argon plasma brush with air addition is employed to treat polyethylene terephthalate(PET)surface in order to improve its hydrophilicity.Results indicate that the plasma plume generated by the p...An atmospheric pressure argon plasma brush with air addition is employed to treat polyethylene terephthalate(PET)surface in order to improve its hydrophilicity.Results indicate that the plasma plume generated by the plasma brush presents periodically pulsed current despite a direct current voltage is applied.Voltage-current curve reveals that there is a transition from a Townsend discharge regime to a glow one during one discharge period.Optical emission spectrum indicates that more oxygen atoms are produced in the plume with increasing air content,which leads to the better hydrophilicity of PET surface after plasma treatment.Besides,an aging behavior is also observed.The hydrophilicity improvement is attributed to the production of oxygen functional groups,which increase in number with increasing air content.Moreover,some grain-like structures are observed on the treated PET surface,and its mean roughness increases with increasing air content.These results are of great importance for the hydrophilicity improvement of PET surface with a large scale.展开更多
The observations of long-lived surface nanobubbles in various experiments have presented a theoretical challenge, as they were supposed to be dissolved in microseconds owing to the high Laplace pressure. However, an i...The observations of long-lived surface nanobubbles in various experiments have presented a theoretical challenge, as they were supposed to be dissolved in microseconds owing to the high Laplace pressure. However, an increasing number of studies suggest that contact line pinning, together with certain levels of oversaturation, is responsible for the anomalous stability of surface nanobubbles. This mechanism can interpret most characteristics of surface nanobubbles. Here, we summarize recent theoretical and computational work to explain how the surface nanobubbles become stable with contact line pinning. Other related work devoted to understanding the unusual behaviors of pinned surface nanobubbles is also reviewed here.展开更多
Wettability alteration of carbonate reservoirs from oil-wet to water-wet is an important method to increase the efficiency of oil recovery. Interaction between surfactants and polymers can enhance the effectiveness of...Wettability alteration of carbonate reservoirs from oil-wet to water-wet is an important method to increase the efficiency of oil recovery. Interaction between surfactants and polymers can enhance the effectiveness of surfactants in EOR applications. In this study, the interaction of polyethylene glycol(PEG) with an ionic surfactant, sodium dodecyl sulphate(SDS),is evaluated on an oil-wet carbonate rock surface by using contact angle measurements. The results reveal that wettability alteration of carbonate rocks is achieved through PEG/SDS interaction on the rock surface above a critical aggregation concentration(CAC). The behaviour of PEG/SDS aqueous solutions is evaluated using surface and interfacial tension measurements. Furthermore, the effect of PEG and SDS concentrations and impact of electrolyte addition on PEG/SDS interaction are investigated. It is shown that electrolyte(NaCl) can effectively decrease the CAC values and accordingly initiate the wettability alteration of rocks. Moreover, in a constant SDS concentration, the addition of NaCl leads to a reduction in the contact angle, which can also be obtained by increasing the aging time, temperature and pre-adsorption of PEG on the rock surface.展开更多
To achieve an atmospheric pressure glow discharge（APGD）in air and modify the surface of polyester thread using plasma,the electric field distribution and discharge characteristics under different conditions were stu...To achieve an atmospheric pressure glow discharge（APGD）in air and modify the surface of polyester thread using plasma,the electric field distribution and discharge characteristics under different conditions were studied.We found that the region with a strong electric field,which was formed in a tiny gap between two electrodes constituting a line-line contact electrode structure,provided the initial electron for the entire discharge process.Thus,the discharge voltage was reduced.The dielectric barrier of the line-line contact electrodes can inhibit the generation of secondary electrons.Thus,the transient current pulse discharge was reduced significantly,and an APGD in air was achieved.We designed double layer line-line contact electrodes,which can generate the APGD on the surface of a material under treatment directly.A noticeable change in the surface morphology of polyester fiber was visualized with the aid of a scanning electron microscope（SEM）.Two electrode structures-the multi-row line-line and double-helix line-line contact electrodes-were designed.A large area of the APGD plasma with flat and curved surfaces can be formed in air using these contact electrodes.This can improve the efficiency of surface treatment and is significant for the application of the APGD plasma in industries.展开更多
Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topogra...Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topography and surface chemistry of the treated F2311 films were characterized by contact angle measurement, atomic force microscopy （AFM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The experimental results showed that a short time air plasma treatment led to morphological, wettability and chemical changes in the F2311 films. The surface hydrophilicity increased greatly after the plasma treatment, the static water contact angle decreased from 98.6° to 32°, and oxygen containing groups （C=O, O-C=O, etc. ） were introduced. Atomic force microscopy revealed that plasma produced by DBD etched F2311 films obviously. The roughness of the samples increased remarkably with the formation of peaks and valleys on the treated surfaces. The increased surface wettability may be correlated with both the introduction of hydrophilic groups due to air plasma oxidation of the surface and the change in surface morphology etched by DBD.展开更多
The wettability of rocks affects the balance between capillary and viscous forces during multiphase flow through porous media,which in turn determines the fluid displacement process governing the recovery of oil from ...The wettability of rocks affects the balance between capillary and viscous forces during multiphase flow through porous media,which in turn determines the fluid displacement process governing the recovery of oil from subsurface formations.In this work,the mechanism of wettability reversal of aged synthetic sandstones by metal oxide nanoparticles(SiO_(2) and Al_(2)O_(3))was investigated with particular focus on the impact of surface roughness,zeta potential,and temperature.The synthetic surfaces were prepared from powders of Berea sandstone with known grain size ranges and their average roughness and roughness ratio were obtained from the 3D surface reconstruction of their microscope images.Each surface was subsequently aged in Permian crude oil to alter its wettability.For surfaces with larger grain sizes and lower surface roughness ratios,the lower capillary pressure allowed stronger oil/surface interactions,leading to enhanced oil-wetness.The wettability alteration effects of nanoparticles were then examined through real-time top view imaging and dynamic front view contact angle experiments.The negatively charged SiO_(2) nanoparticles rapidly reversed the sandstone wettability,indicating their potential applicability as wettability alteration agents.By contrast,the positively charged Al_(2)O_(3) counterpart caused no wettability reversal.The mechanism of wettability alteration was further studied by microscale interaction analyses and nanoscale transmission electron microscopy.Because nanoparticles were only a few nanometers large,the microscale roughness had a negligible effect on the wettability reversal.Instead,the combined effect of van der Waals dispersion forces and surface-charge-induced electrostatic forces were recognized as the two key factors affecting the wettability of sandstone particles.Such interactions may be curbed at elevated temperatures due to a decrease in the zeta potential and colloidal stability of the particles.展开更多
Superhydrophobic surfaces have attracted extensive interests and researches into their fundamentals and potential applications.Laser texturing provides the convenience to fabricate the hierarchical micro/nanostructure...Superhydrophobic surfaces have attracted extensive interests and researches into their fundamentals and potential applications.Laser texturing provides the convenience to fabricate the hierarchical micro/nanostructures for superhydrophobicity.However,after laser texturing,long wettability transition time from superhydrophilicity to superhydrophobicity is a barrier to mass production and practical industrial applications.External stimuli have been applied to change the surface composition and/or the surface morphology to reduce wettability transition time.Herein,by temperature tuning,wettability transition of laser textured brass surfaces is investigated.Scanning electron microscopy and surface contact angle measurement are employed to characterize the surface morphology and wettability behavior of the textured brass surfaces.By low-temperature heating(100℃~150℃),partial deoxidation of the top Cu O layer occurs to form hydrophobic Cu_2O.Therefore,superhydrophobicity without any chemical coating and surface modification could be achieved in a short time.Furthermore,after low-temperature heating,the low adhesive force between the water droplet and the sample surface is demonstrated for the laser textured brass surface.This study provides a simple method to fabricate the micro/nanostructure surfaces with controllable wettability for the potential applications.展开更多
The tobacco leaves were treated with low-temperature plasma in Ar, N2, O2, and air atmospheres at different powers (60―130 W). The surface-elemental components, their relative contents, and the functional groups of t...The tobacco leaves were treated with low-temperature plasma in Ar, N2, O2, and air atmospheres at different powers (60―130 W). The surface-elemental components, their relative contents, and the functional groups of the surface components of the tobacco leaves were determined using XPS (X-ray photoelectron spectroscopy). The ex- perimental results showed that the percentage of the elements C, N, and O had changed considerably and a large number of polar functional groups containing oxygen atoms were incorporated into the components on the tobacco surfaces. The measurements of the surface contact angle showed that the surface contact angle of the modified tobacco leaves was 0 degree, whereas it was 110 degrees before the plasma treatment. These results indicate that the wettability of the modified tobacco leaves improved dramatically. This work may be significant for future researches on the surface modification of the tobacco leaves.展开更多
Liquid metal alloys(LMAs) are the potential candidates of thermal interface materials(TIMs) for electronics cooling.In the present work, buffer layers of Ag, Ti, Cu, Ni, Mo, and W were deposited on polished Cu plates ...Liquid metal alloys(LMAs) are the potential candidates of thermal interface materials(TIMs) for electronics cooling.In the present work, buffer layers of Ag, Ti, Cu, Ni, Mo, and W were deposited on polished Cu plates by DC magnetron sputtering, the contact angles of de-ionized water and diiodomethane on the buffer layers were measured by an easy drop shape analyzer and the surface free energies(SFEs) of the buffer layers were calculated by the Owens–Wendt–Kaelble equation. Samples were prepared by sandwiching the filmed Cu plates and LMAs. The thermal properties of the samples were measured by laser flash analysis method. The SFE of the buffer layer has a strong influence on the interface heat transfer, whereas the measurement temperature has no obvious effect on the thermal properties of the samples. As the SFE of the buffer layer increases, the wettability, thermal diffusivity, and thermal conductivity are enhanced, and the thermal contact resistance is decreased.展开更多
In this work, three-dimensional graphene foams （GFs） are synthesized and characterized by scanning electron micro- scope （SEM） and Raman spectroscopy. The SEM images indicate that after the growth of graphene, the...In this work, three-dimensional graphene foams （GFs） are synthesized and characterized by scanning electron micro- scope （SEM） and Raman spectroscopy. The SEM images indicate that after the growth of graphene, the graphene covers the surface of nickel （Ni） foam uniformly. Raman spectra show that the percentages of monolayer, bilayer, trilayer, and multilayer graphenes are - 58%, - 32%, - 8%, and ,.o 2%, respectively. The contact angle （CA） （-- 12°） of water droplet （3 p-L） on GF is found to be larger than that on Ni foam （,- 107°）, indicating that graphenes have changed the surface wettability of the Ni foam. Meanwhile, the dynamic characteristics of CA of water droplet on GF are different from those on Ni foam. The mechanisms for different behaviors are discussed, which are attributed to volatilization and seepage of water droplets.展开更多
Cupric hydroxide films with a new hierarchical architecture consisting of beautiful nanotubes and nanoflowers were directly fabricated on copper substrate via a solution-immersion process at a constant temperature of ...Cupric hydroxide films with a new hierarchical architecture consisting of beautiful nanotubes and nanoflowers were directly fabricated on copper substrate via a solution-immersion process at a constant temperature of 23 ℃. Stable superhydrophobic Cu（OH）2 surface was obtained after Cu（OH）2 films were modified with hydrolyzed 1H, 1H, 2H, 2H-perfluorooctyltrichlorosilane （CsH4CI3F13Si, FOTMS）. The surface morphology and composition of the film were studied using scanning electron microscopy （SEM）, X-ray diffraction （XRD）, and X-ray photoelectron spectroscopy （XPS）, respectively. Result shows that the surface of Cu（OH）2 films directly grown on copper substrate was hydrophilic, whereas the modified Cu（OH）2 films exhibited the superhydrophobicity with a water contact angle （CA） of about 160.8°, as well as a small sliding angle （SA） of about 1°. The special hierarchical structure, along with the slow surface energy leads to the high superhydrophobicity of the surface.展开更多
基金Project supported by the National Key Research and Development Program of China(Grant No.2022YFB3608601).
文摘The ohmic contact interface between diamond and metal is essential for the application of diamond detectors.Surface modification can significantly affect the contact performance and eliminate the interface polarization effect.However,the radiation stability of a diamond detector is also sensitive to surface modification.In this work,the influence of surface modification technology on a diamond ohmic contact under high-energy radiation was investigated.Before radiation,the specific contact resistivities(ρc)between Ti/Pt/Au-hydrogen-terminated diamond(H-diamond)and Ti/Pt/Au-oxygenterminated diamond(O-diamond)were 2.0×10^(-4)W·cm^(2) and 4.3×10^(-3)Wcm^(2),respectively.After 10 MeV electron radiation,the ρc of Ti/Pt/Au H-diamond and Ti/Pt/Au O-diamond were 5.3×10^(-3)W·cm^(2)and 9.1×10^(-3)W·cm^(2),respectively.The rates of change of ρc of H-diamond and O-diamond after radiation were 2550%and 112%,respectively.The electron radiation promotes bond reconstruction of the diamond surface,resulting in an increase in ρc.
基金Supported by the National Natural Science Foundation of China under Grant No 61306113
文摘Nonalloyed ohmic contacts regrown by metal-organic chemical vapor deposition are performed on AlGaN/GaN high-electron-mobility transistors. Low ohmic contact resistance of 0.15Ω.mm is obtained. It is found that the sidewall obliquity near the regrown interface induced by the plasma dry etching has great influence on the total contact resistance. The fabricated device with a 100-nm T-shaped gate demonstrates a maximum drain current density of 0.95 A/mm at Vgs = 1 V and a maximum peak extrinsic transcondutance Gm of 216mS/ram. Moreover, a current gain cut-off frequency fT of 115 GHz and a maximum oscillation frequency fmax of 127 GHz are achieved.
基金supported by the National Natural Science Foundation of China(Grant Nos.52075249,51505217,51435008,and 51705247)。
文摘Contact electrification(CE)is a pretty common phenomenon,but still is poorly understood.The long-standing controversy over the mechanisms of CE related to polymers is particularly intense due to their complexity.In this paper,the CE between metals and polymers is systematically studied,which shows the evolution of surfaces is accompanied by variations of CE outputs.The variations of CE charge quantity are closely related to the creep and deformation of the polymer and metal surfaces.Then the relationship between CE and polymer structures is put forward,which is essentially determined by the electronegativity of elements and the functional groups in the polymers.The effects of load and contact frequency on the CE process and outputs are also investigated,indicating the increase of CE charge quantity with load and frequency.Material transfer from polymer to metal is observed during CE while electrons transfer from metal to polymer,both of which are believed to have an influence on each other.The findings advance our understanding of the mechanism of CE between metal and polymers,and provides insights into the performance of CE-based application in various conditions,which sheds light on the design and optimization of CE-based energy harvest and self-powered sensing devices.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12025407,11934003,9185012011774328)+1 种基金the Key R&D Program of China(Grant No.2016YFA0300902)the Chinese Academy of Sciences。
文摘Interactions between water and solid substrates are of fundamental importance to various processes in nature and industry.Electric control is widely used to modify interfacial water,where the influence of surface charges is inevitable.Here we obtain positively and negatively charged surfaces using Li Ta O_(3) crystals and observe that a large net surface charge up to 0.1 C/m;can nominally change the contact angles of pure water droplets comparing to the same uncharged surface.However,even a small amount of surface charge can efficiently increase the water contact angle in the presence of aerosols.Our results indicate that such surface charges can hardly affect the structure of interfacial water molecular layers and the morphology of the macroscopic droplet,while adsorption of a small amount of organic contaminants from aerosols with the help of Coulomb attraction can notably decrease the wettability of solid surface.Our results not only provide a fundamental understanding of the interactions between charged surfaces and water,but also help to develop new techniques on electric control of wettability and microfluidics in real aerosol environments.
基金the Natural Science Basic Research Program of Shaanxi(Program No.2023-JC-YB-351)the Scientific Research Program Funded by the Shaanxi Provincial Education Department(Program No.20JS118)the Xi’an Shiyou University Graduate Innovation and Practice Ability Training Plan(YCS21212097,YCS21212092).
文摘Traditional microstructure scale parameters have difficulty describing the structure and distribution of a roughmaterial’s surface morphology comprehensively and quantitatively. This study constructs hydrophilic and underwateroleophobic surfaces based on polyvinylidene fluoride (PVDF) using a chemical modification method, and the fractaldimension and multifractal spectrum are used to quantitatively characterize the microscopic morphology. A new contactangle prediction model for underwater oleophobic surfaces is established. The results show that the fractal dimension ofthe PVDF surface first increases and then decreases with the reaction time. The uniformity characterized by the multifractalspectrum was generally consistent with scanning electron microscope observations. The contact angle of water droplets onthe PVDF surface is negatively correlated with the fractal dimension, and oil droplets in water are positively correlated.When the fractal dimension is 2.0975, the new contact angle prediction model has higher prediction accuracy. Themaximum and minimum relative deviations of the contact angle between the theoretical and measured data are 18.20%and 0.72%, respectively. For water ring transportation, the larger the fractal dimension and spectral width of the materialsurface, the smaller the absolute value of the spectral difference, the stronger the hydrophilic and oleophobic properties, andthe better the water ring transportation stability.
基金the financial support provided by the Natural Sciences and Engineering Research Council of Canada(NSERC)
文摘Superhydrophobic aluminum surfaces have been prepared by means of electrodeposition of copper on aluminum surfaces, followed by electrochemical modification using stearic acid organic molecules. Scanning electron microscopy(SEM) images show that the electrodeposited copper films follow "island growth mode" in the form of microdots and their number densities increase with the rise of the negative deposition potentials. At an electrodeposition potential of-0.2 V the number density of the copper microdots are found to be 4.5×104cm^(-2)that are increased to 2.9×105cm^(-2)at a potential of-0.8 V. Systematically, the distances between the microdots are found to be reduced from 26.6 μm to 11.03 μm with the increase of negative electrochemical potential from-0.2 V to-0.8 V. X-ray diffraction(XRD) analyses have confirmed the formation of copper stearate on the stearic acid modified copper films. The roughness of the stearic acid modified electrodeposited copper films is found to increase with the increase in the density of the copper microdots. A critical copper deposition potential of-0.6 V in conjunction with the stearic acid modification provides a surface roughness of 6.2 μm with a water contact angle of 157?, resulting in superhydrophobic properties on the aluminum substrates.
基金partly supported by National Natural Science Foundation of China under Grant No. 51477164the National Basic Research Program of China under Grant No. 2014CB239505-03+1 种基金the State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources under Grant No. LAPS16013the Science and Technology Project of State Grid Corporation of China
文摘Nanosecond-pulse diffuse discharges could provide high-density plasma and high-energy electrons at atmospheric pressure. In this paper, the surface treatment of Cu by nanosecond-pulse diffuse discharges is conducted in atmospheric air. Factors influencing the water contact angle （WCA）, chemical composition and microhardness, such as the gap spacing and treatment time, are investigated. The results show that after the plasma surface treatment, the WCA considerably decreases from 87~ to 42.3~, and the surface energy increases from 20.46 mJ m-2 to 66.28 mJ m-2. Results of energy dispersive x-ray analysis show that the concentration of carbon decreases, but the concentrations of oxygen and nitrogen increase significantly. Moreover, the microhardness increases by approximately 30% after the plasma treatment. The aforementioned changes on the Cu surface indicate the plasma surface treatment enhances the hydrophilicity and microhardness, and it cleans the carbon and achieves oxidization on the Cu surface. Furthermore, by increasing the gap spacing and treatment time, better treatment effects can be obtained. The micmhardness in the case of a 2.5 cm gap is higher than that in the case of a 3 cm gap. More oxygen and nitrogen species appear on the Cu surface for the 2.5 cm gap treatment than for the 3 cm gap treatment. The WCA significantly decreases with the treatment thne when it is no longer than 90 s, and then it reaches saturation. In addition, more oxygen-containing and nitrogen-containing groups appear after extended plasma treatment time. They contribute to the improvement of the hydrophilicity and oxidation on the Cu surface.
基金supported by National Natural Science Foundation of China(Nos.51077008 and 11247239)
文摘An atmospheric pressure plasma jet generated in Ar and O2/Ar mixtures has been investigated by specially designed equipment with double power electrodes at 20~32 kHz, and their effects on the cleaning of surfaces have been studied. Properties of the jet discharge are studied by electrical diagnostics, including the waveform of discharge voltage, discharge current and the Q-V Lissajous figures. The optical emission spectroscopy is used to measure the plasma parameters, such as the excitation temperature and the gas temperature. It is found that the consumed power and the excitation temperature increase with increase of the discharge frequency. On the other hand, at the same discharge frequency, these parameters in O2/Ar mixture plasma are found to be much larger. The effect on surface cleaning is studied from the changes in the contact angle. For Ar plasma jet, the contact angle decreases with increase of the discharge frequency. For O2/Ar mixture plasma jet, the contact angle decreases with increase of discharge frequency up to 26 kHz, however, further increase of discharge frequency does not show further decrease in the contact angle. At the same discharge frequency, the contact angle after O2/Ar mixture plasma cleaning is found to be much lower compared to the case of pure Ar. From the results of quadrupole mass-spectrum analysis, we can identify more fragment molecules of CO and H2O in the emitted gases after O2/Ar plasma jet treatment compared with Ar plasma jet treatment, which are produced by the decomposition of surface organic contaminants during the cleaning process.
基金Supported by the Foundation for the Author of National Excellent Doctoral Dissertation of China (Grant No. 200352)
文摘In this study, the contact angles of three different reference liquids （including distilled water, diiodomethane, and formamide） and PF resin on the surfaces of Chinese fir （Cunningharnia lanceolata） samples untreated or treated with different concentrations of ACQ-D （ammoniacal copper quat Type D） solutions were measured. Then, the surface free energy was calculated by two approaches： acid-base approach and geometric mean approach. ACQ-D treatment caused higher contact angles and lower surface free energies at a retention level corresponding to the commodity treated wood products. When wood was treated with much higher concentrations of ACQ-D, the total surface free energy of wood would be higher than the untreated control. Acid-base/polar components related with the hydrogen bonding state in wood were considered to be responsible for the observed changes according to the applied approaches. The hydrophobic properties and also higher contact angles of PF resin drop on wood surfaces after ACQ-D treatment at a reasonable retention level confirms the changes on surface free energy.
基金supported by National Natural Science Foundation of China(Nos.11875121,11575050 and51977057)the Midwest Universities Comprehensive Strength Promotion Project+4 种基金the Natural Science Foundation of Hebei Province,China(Nos.A2019201100,A2020201025)College Hundred Outstanding Innovative Talent Support Program of Hebei Education Bureau(No.SLRC2017021)Post-graduate’s Innovation Fund Project of Hebei Province(Nos.CXZZBS2019023,CXZZBS2019029)the Natural Science Interdisciplinary Research Program of Hebei University(No.DXK201908)Post-graduate’s Innovation Fund Project of Hebei University(No.HBU2021bs011)。
文摘An atmospheric pressure argon plasma brush with air addition is employed to treat polyethylene terephthalate(PET)surface in order to improve its hydrophilicity.Results indicate that the plasma plume generated by the plasma brush presents periodically pulsed current despite a direct current voltage is applied.Voltage-current curve reveals that there is a transition from a Townsend discharge regime to a glow one during one discharge period.Optical emission spectrum indicates that more oxygen atoms are produced in the plume with increasing air content,which leads to the better hydrophilicity of PET surface after plasma treatment.Besides,an aging behavior is also observed.The hydrophilicity improvement is attributed to the production of oxygen functional groups,which increase in number with increasing air content.Moreover,some grain-like structures are observed on the treated PET surface,and its mean roughness increases with increasing air content.These results are of great importance for the hydrophilicity improvement of PET surface with a large scale.
基金Project supported by the National Natural Science Foundation of China(Grant No.91434204)
文摘The observations of long-lived surface nanobubbles in various experiments have presented a theoretical challenge, as they were supposed to be dissolved in microseconds owing to the high Laplace pressure. However, an increasing number of studies suggest that contact line pinning, together with certain levels of oversaturation, is responsible for the anomalous stability of surface nanobubbles. This mechanism can interpret most characteristics of surface nanobubbles. Here, we summarize recent theoretical and computational work to explain how the surface nanobubbles become stable with contact line pinning. Other related work devoted to understanding the unusual behaviors of pinned surface nanobubbles is also reviewed here.
文摘Wettability alteration of carbonate reservoirs from oil-wet to water-wet is an important method to increase the efficiency of oil recovery. Interaction between surfactants and polymers can enhance the effectiveness of surfactants in EOR applications. In this study, the interaction of polyethylene glycol(PEG) with an ionic surfactant, sodium dodecyl sulphate(SDS),is evaluated on an oil-wet carbonate rock surface by using contact angle measurements. The results reveal that wettability alteration of carbonate rocks is achieved through PEG/SDS interaction on the rock surface above a critical aggregation concentration(CAC). The behaviour of PEG/SDS aqueous solutions is evaluated using surface and interfacial tension measurements. Furthermore, the effect of PEG and SDS concentrations and impact of electrolyte addition on PEG/SDS interaction are investigated. It is shown that electrolyte(NaCl) can effectively decrease the CAC values and accordingly initiate the wettability alteration of rocks. Moreover, in a constant SDS concentration, the addition of NaCl leads to a reduction in the contact angle, which can also be obtained by increasing the aging time, temperature and pre-adsorption of PEG on the rock surface.
文摘To achieve an atmospheric pressure glow discharge（APGD）in air and modify the surface of polyester thread using plasma,the electric field distribution and discharge characteristics under different conditions were studied.We found that the region with a strong electric field,which was formed in a tiny gap between two electrodes constituting a line-line contact electrode structure,provided the initial electron for the entire discharge process.Thus,the discharge voltage was reduced.The dielectric barrier of the line-line contact electrodes can inhibit the generation of secondary electrons.Thus,the transient current pulse discharge was reduced significantly,and an APGD in air was achieved.We designed double layer line-line contact electrodes,which can generate the APGD on the surface of a material under treatment directly.A noticeable change in the surface morphology of polyester fiber was visualized with the aid of a scanning electron microscope（SEM）.Two electrode structures-the multi-row line-line and double-helix line-line contact electrodes-were designed.A large area of the APGD plasma with flat and curved surfaces can be formed in air using these contact electrodes.This can improve the efficiency of surface treatment and is significant for the application of the APGD plasma in industries.
基金the Joint Foundation of the Council of National Natural Science Foundation of China(NSFC)China Academy of Engineering Physics(CAEP)the National Natural Science Foundation of China(NSAF United Foundation)
文摘Fluoride rubber F2311 film, an alternating copolymer of CF2-CFC1 （CTFE） and CH2-CF2 （VF2） components, was treated by atmospheric pressure dielectric barrier discharge （DBD） in air. The surface structure, topography and surface chemistry of the treated F2311 films were characterized by contact angle measurement, atomic force microscopy （AFM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The experimental results showed that a short time air plasma treatment led to morphological, wettability and chemical changes in the F2311 films. The surface hydrophilicity increased greatly after the plasma treatment, the static water contact angle decreased from 98.6° to 32°, and oxygen containing groups （C=O, O-C=O, etc. ） were introduced. Atomic force microscopy revealed that plasma produced by DBD etched F2311 films obviously. The roughness of the samples increased remarkably with the formation of peaks and valleys on the treated surfaces. The increased surface wettability may be correlated with both the introduction of hydrophilic groups due to air plasma oxidation of the surface and the change in surface morphology etched by DBD.
基金the financial support from Baker Hughes Company and the U.S.National Science Foundation(NSF CAREER Award 1351296).
文摘The wettability of rocks affects the balance between capillary and viscous forces during multiphase flow through porous media,which in turn determines the fluid displacement process governing the recovery of oil from subsurface formations.In this work,the mechanism of wettability reversal of aged synthetic sandstones by metal oxide nanoparticles(SiO_(2) and Al_(2)O_(3))was investigated with particular focus on the impact of surface roughness,zeta potential,and temperature.The synthetic surfaces were prepared from powders of Berea sandstone with known grain size ranges and their average roughness and roughness ratio were obtained from the 3D surface reconstruction of their microscope images.Each surface was subsequently aged in Permian crude oil to alter its wettability.For surfaces with larger grain sizes and lower surface roughness ratios,the lower capillary pressure allowed stronger oil/surface interactions,leading to enhanced oil-wetness.The wettability alteration effects of nanoparticles were then examined through real-time top view imaging and dynamic front view contact angle experiments.The negatively charged SiO_(2) nanoparticles rapidly reversed the sandstone wettability,indicating their potential applicability as wettability alteration agents.By contrast,the positively charged Al_(2)O_(3) counterpart caused no wettability reversal.The mechanism of wettability alteration was further studied by microscale interaction analyses and nanoscale transmission electron microscopy.Because nanoparticles were only a few nanometers large,the microscale roughness had a negligible effect on the wettability reversal.Instead,the combined effect of van der Waals dispersion forces and surface-charge-induced electrostatic forces were recognized as the two key factors affecting the wettability of sandstone particles.Such interactions may be curbed at elevated temperatures due to a decrease in the zeta potential and colloidal stability of the particles.
基金supported by the National Natural Science Foundation of China (U1609209)Open Program of Laser Precision Machining Engineering Technology Research Center of Fujian Province (2016JZA001)
文摘Superhydrophobic surfaces have attracted extensive interests and researches into their fundamentals and potential applications.Laser texturing provides the convenience to fabricate the hierarchical micro/nanostructures for superhydrophobicity.However,after laser texturing,long wettability transition time from superhydrophilicity to superhydrophobicity is a barrier to mass production and practical industrial applications.External stimuli have been applied to change the surface composition and/or the surface morphology to reduce wettability transition time.Herein,by temperature tuning,wettability transition of laser textured brass surfaces is investigated.Scanning electron microscopy and surface contact angle measurement are employed to characterize the surface morphology and wettability behavior of the textured brass surfaces.By low-temperature heating(100℃~150℃),partial deoxidation of the top Cu O layer occurs to form hydrophobic Cu_2O.Therefore,superhydrophobicity without any chemical coating and surface modification could be achieved in a short time.Furthermore,after low-temperature heating,the low adhesive force between the water droplet and the sample surface is demonstrated for the laser textured brass surface.This study provides a simple method to fabricate the micro/nanostructure surfaces with controllable wettability for the potential applications.
基金Supported by Research Fund of Monopoly Administration of Tobacco of China (No. 110200201016)
文摘The tobacco leaves were treated with low-temperature plasma in Ar, N2, O2, and air atmospheres at different powers (60―130 W). The surface-elemental components, their relative contents, and the functional groups of the surface components of the tobacco leaves were determined using XPS (X-ray photoelectron spectroscopy). The ex- perimental results showed that the percentage of the elements C, N, and O had changed considerably and a large number of polar functional groups containing oxygen atoms were incorporated into the components on the tobacco surfaces. The measurements of the surface contact angle showed that the surface contact angle of the modified tobacco leaves was 0 degree, whereas it was 110 degrees before the plasma treatment. These results indicate that the wettability of the modified tobacco leaves improved dramatically. This work may be significant for future researches on the surface modification of the tobacco leaves.
基金Project supported by the National Natural Science Foundation of China(Grant No.11874191)the Natural Science Foundation of Shandong Province,China(Grant No.ZR2016FM38)
文摘Liquid metal alloys(LMAs) are the potential candidates of thermal interface materials(TIMs) for electronics cooling.In the present work, buffer layers of Ag, Ti, Cu, Ni, Mo, and W were deposited on polished Cu plates by DC magnetron sputtering, the contact angles of de-ionized water and diiodomethane on the buffer layers were measured by an easy drop shape analyzer and the surface free energies(SFEs) of the buffer layers were calculated by the Owens–Wendt–Kaelble equation. Samples were prepared by sandwiching the filmed Cu plates and LMAs. The thermal properties of the samples were measured by laser flash analysis method. The SFE of the buffer layer has a strong influence on the interface heat transfer, whereas the measurement temperature has no obvious effect on the thermal properties of the samples. As the SFE of the buffer layer increases, the wettability, thermal diffusivity, and thermal conductivity are enhanced, and the thermal contact resistance is decreased.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.10774032 and 90921001)the Key Knowledge Innovation Project ofthe Chinese Academy of Sciences on Water Science Research,Instrument Developing Project of the Chinese Academy of Sciences(Grant No.Y2010031)
文摘In this work, three-dimensional graphene foams （GFs） are synthesized and characterized by scanning electron micro- scope （SEM） and Raman spectroscopy. The SEM images indicate that after the growth of graphene, the graphene covers the surface of nickel （Ni） foam uniformly. Raman spectra show that the percentages of monolayer, bilayer, trilayer, and multilayer graphenes are - 58%, - 32%, - 8%, and ,.o 2%, respectively. The contact angle （CA） （-- 12°） of water droplet （3 p-L） on GF is found to be larger than that on Ni foam （,- 107°）, indicating that graphenes have changed the surface wettability of the Ni foam. Meanwhile, the dynamic characteristics of CA of water droplet on GF are different from those on Ni foam. The mechanisms for different behaviors are discussed, which are attributed to volatilization and seepage of water droplets.
基金Sponsored by the National Natural Science Foundation of China(20773014/B030202)the "111" Project of China(B07012)
文摘Cupric hydroxide films with a new hierarchical architecture consisting of beautiful nanotubes and nanoflowers were directly fabricated on copper substrate via a solution-immersion process at a constant temperature of 23 ℃. Stable superhydrophobic Cu（OH）2 surface was obtained after Cu（OH）2 films were modified with hydrolyzed 1H, 1H, 2H, 2H-perfluorooctyltrichlorosilane （CsH4CI3F13Si, FOTMS）. The surface morphology and composition of the film were studied using scanning electron microscopy （SEM）, X-ray diffraction （XRD）, and X-ray photoelectron spectroscopy （XPS）, respectively. Result shows that the surface of Cu（OH）2 films directly grown on copper substrate was hydrophilic, whereas the modified Cu（OH）2 films exhibited the superhydrophobicity with a water contact angle （CA） of about 160.8°, as well as a small sliding angle （SA） of about 1°. The special hierarchical structure, along with the slow surface energy leads to the high superhydrophobicity of the surface.
