When the interface of a multilayered saturated soil is rough with noticeable gaps, heat flow lines converge towards the actual contact points, causing thermal flow contraction. Conversely, in the interface between two...When the interface of a multilayered saturated soil is rough with noticeable gaps, heat flow lines converge towards the actual contact points, causing thermal flow contraction. Conversely, in the interface between two layers of soil with different properties, pore water flows slowly along the pore channels, demonstrating laminar flow phenomenon. To predict the thermal contact resistance and flow contact resistance at the interface, this paper constructs general imperfect thermal contact model and general imperfect flow contact model, respectively. Utilizing a thermo-hydro- mechanical coupling model, the thermal consolidation behavior of multilayered saturated soil under two-dimensional conditions is investigated. Fourier and Laplace transformations are applied to decouple the governing equations, yielding expressions for the temperature increment, pore water pressure, and displacement in multilayered saturated soil. The inverse Fourier-Laplace transformation is then used to obtain numerical solutions, which are compared with degeneration solutions to validate the computational accuracy. The differences in the thermal consolidation process under various thermal contact and flow contact resistance models are discussed. Furthermore, the impact of parameters such as the thermal resistance coefficient, partition thermal contact coefficient, flow contact resistance coefficient, and partition flow contact coefficient on thermal consolidation are investigated. Results indicate that thermal contact resistance creates a relative thermal gradient at the interface, leading to increased pore water pressure and reduced displacement nearby. In contrast, flow contact resistance generates a relative pore pressure gradient at the interface, resulting in increased displacement within the saturated soil with minimal effect on temperature increment distribution.展开更多
Asphalt mixture pavement reheating is one of the important steps in hot in-place recycling(HIR).To improve the heating speed of asphalt pavement in HIR,based on the numerical analysis model of asphalt mixture heating ...Asphalt mixture pavement reheating is one of the important steps in hot in-place recycling(HIR).To improve the heating speed of asphalt pavement in HIR,based on the numerical analysis model of asphalt mixture heating process,a new multi-layer low-temperature heating method(MLHM)was proposed.Considering input heat flux,the thermal capacity and thermal resistance of asphalt mixture,the heat transfer model was established based on energy conservation law.By heating the asphalt mixture in layers,it changes the situation that the heat energy can only be input from the upper surface of the asphalt mixture pavement.Through the simulation of the heating method of asphalt mixture in the existing technology,the result shows that the existing heating methods lead to serious aging or charring of the asphalt mixture.By MLHM,the upper and the bottom of the asphalt mixture are heated at the same time,and the heating temperature is lower than other heat methods,which not only reduces the heating thickness and increases the heating area of the asphalt mixture pavement,but also improves the heating speed,saves the energy resource and ensures the heating quality.Especially,by MLHM,the heating uniformity is better and speed is faster.展开更多
Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the co...Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the conditions of COFCC with n(O)-n(C) (molar ratio) as 1.00-0.84 and n(SiO2)-n(CaO) as 1.00-0.39, the samples were heated by 10 kW microwave power to reach the given temperatures and held for different times respectively. The results show that the low-C-Cr ferrochromium metal phase in the reduced materials forms before the high-C-Cr ferrochromium metal phase does. With increasing temperature the C content of ferrochromium metals is in a positive correlation with the content of Cr. The C content of ferrochromium metal in reduced materials is 0-10.07% with an average value of 4.68%. With the increase of holding time the Cr content in ferrochromium metals is in a negative correlation with the content of C, while the content of Fe changes in the contrary way. In the microwave field the kinetic conditions of carburization are closely related with the temperature of microwave heating, holding time and carbon fitting ratio.展开更多
Double self-adaptive fuzzy PID algorithm-based control strategy was proposed to construct quasi-cascade control system to control the speed of the acid-pickling process of titanium plates and strips. It is very useful...Double self-adaptive fuzzy PID algorithm-based control strategy was proposed to construct quasi-cascade control system to control the speed of the acid-pickling process of titanium plates and strips. It is very useful in overcoming non-linear dynamic behavior, uncertain and time-varying parameters, un-modeled dynamics, and couples between the automatic turbulence control (ATC) and the automatic acid temperature control (AATC) with varying parameters during the operation process. The quasi-cascade control system of inner and outer loop self-adaptive fuzzy PID controller was built, which could effectively control the pickling speed of plates and strips. The simulated results and real application indicate that the plates and strips acid pickling speed control system has good performances of adaptively tracking the parameter variations and anti-disturbances, which ensures the match of acid pickling temperature and turbulence of flowing with acid pickling speed, improving the surface quality of plates and strips acid pickling, and energy efficiency.展开更多
The exothermic efficiency of microwave heating an electrolyte/water solution is remarkably high due to the dielectric heating by orientation polarization of water and resistance heating by the Joule process occurred s...The exothermic efficiency of microwave heating an electrolyte/water solution is remarkably high due to the dielectric heating by orientation polarization of water and resistance heating by the Joule process occurred simultaneously compared with pure water.A three-dimensional finite element numerical model of multi-feed microwave heating industrial liquids continuously flowing in a meter-scale circular tube is presented.The temperature field inside the applicator tube in the cavity is solved by COMSOL Multiphysics and professional programming to describe the momentum,energy and Maxwell's equations.The evaluations of the electromagnetic field,the temperature distribution and the velocity field are simulated for the fluids dynamically heated by singleand multi-feed microwave system,respectively.Both the pilot experimental investigations and numerical results of microwave with single-feed heating for fluids with different effective permittivity and flow rates show that the presented numerical modeling makes it possible to analyze dynamic process of multi-feed microwave heating the industrial liquid.The study aids in enhancing the understanding and optimizing of dynamic process in the use of multi-feed microwave heating industrial continuous flow for a variety of material properties and technical parameters.展开更多
In this paper,the performance of a solar thermal system with a focus on space heating was investigated.A 70 m^(2) detached house was considered in the weather conditions of the city of Tehran,Iran.A thermosyphon solar...In this paper,the performance of a solar thermal system with a focus on space heating was investigated.A 70 m^(2) detached house was considered in the weather conditions of the city of Tehran,Iran.A thermosyphon solar water heater with a flat plate collector combined with an auxiliary electrical heater supplies the heating demand of the house.The proposed system was modeled and analyzed using TRNSYS software.In this regard,the TRNBuild module was employed for the building load calculation.The model has been simulated for one year of operation.The effects of the solar collector’s surface area and storage volume were assessed.The results show that for a solar collector with a 15 m^(2) surface area,the solar fraction is 0.29 in January,during which the solar radiation is the lowest.Using solar collectors of10 m^(2) and 5 m^(2) surface areas,the solar fraction falls to 0.23 and 0.14,respectively in January.Besides,two cases of 150 L and 300 L storage tanks are taken into account.Eventually,it is found that using a 15 m^(2) solar collector and a 150 L storage tank can appropriately provide the building’ s heating demand taking the thermal performance and economic aspects into consideration.展开更多
In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1...In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1400-2600 r/min）, ambient air temperature（2.4-17.8 ℃） and condenser water inlet temperature（30-50℃）. The results show that as engine speed increases from 1400 r/min to 2600 r/min, the total heating capacity and energy consumption increase by about 30% and 89%, respectively; while the heat pump coefficient of performance（COP） and system primary energy ratio（PER） decrease by 44% and 31%, respectively. With the increase of ambient air temperature from 2.4 ℃ to 17.8 ℃, the heat pump COP and system PER increase by 32% and 19%, respectively. Moreover, the heat pump COP and system PER decrease by 27% and 15%, respectively, when the condenser water inlet temperature changes from 30 ℃ to 50 ℃. So, it is obvious that the effect of engine speed on the performance is more significant than the effects of ambient air temperature and condenser water inlet temperature.展开更多
A new iron-making process using carburized pre-reduced iron ore pellets and microwave heating is investigated. The pre-reduced pellets, with a porous structure, and fine particles are carburized homogeneously at 400-6...A new iron-making process using carburized pre-reduced iron ore pellets and microwave heating is investigated. The pre-reduced pellets, with a porous structure, and fine particles are carburized homogeneously at 400-650 ℃ in a CO atmosphere. The carburized carbon not only acts reaction as a reduction agent, but also absorbs microwave in the reduction process. Hence, the carburized pre-reduced pellets can be rapidly reduced by microwave heating. There are three procedures involved in the process, namely, gas-based pre-reduction, low-temperatttre carburization and deep reduction by microwave heating. Carburized pre-reduced iron ore pellets show a rapid temperature rise that is twice as fast as the results for pre-reduced pellets in the laboratory. This not only improves the efficiency of the microwave heating, but also accelerates the reduction of iron oxides. The temperature of the pre-reduced pellets rises to 1050 ℃ in 45 min when the carburization rate is 2.02%, and the metallization rate and compressive strength reach 94.24% and 1725 N/pellet, respectively.展开更多
The resistance heating method has been one of the prospective techniques for hot processing and welding techniques. The thermal behavior under different densities of electric current and the effect of electric current...The resistance heating method has been one of the prospective techniques for hot processing and welding techniques. The thermal behavior under different densities of electric current and the effect of electric current at temperature of 780 oC using low density of electric current of 6.70 A/mm^2 on the B2+O lamellar microstructure were investigated for Ti2AlNb alloy sheet. The stable temperature denoted a balanced state between the Joule heat and the dissipation of heat including heat conduction, convection and radiation while the distribution of temperature was nonuniform. The highest temperatures of electric current heating samples increased as the density of electric current was elevated. In order to understand the specific effect of electric current on B2+O microstructure, heat treatment for microstructural homogeneity was introduced to this study. After that, according to the microstructural observations by common characterization techniques in the resistance-heating sample and the isothermal furnace-heating sample after homogenizing treatment, few significant differences in content and orientation of phases can be directly and explicitly found except the thermal effect from the applied electric current. The results will provide reference to this prospective forming and welding techniques and the application for Ti2AlNb alloys using resistance heating in the near future.展开更多
Personal conditioning system(PCS)is receiving considerable attention due to its energy-saving potential and the ability to satisfy individual comfort requirements.As a part of PCS,personal heating systems can maintain...Personal conditioning system(PCS)is receiving considerable attention due to its energy-saving potential and the ability to satisfy individual comfort requirements.As a part of PCS,personal heating systems can maintain human thermal comfort in cold environments,which leads to their potential role of important heating mode in cold winter,especially in the Hot Summer and Cold Winter regions of China.In order to better promote the development and application of personal heating systems,this paper reviews the published studies.Personal heating systems can be divided into four types based on the mode of heat transfer:conductive,convective,radiative and combinative type.Characteristics of each category and respective devices are introduced.Furthermore,identifying the effects of personal heating on thermal comfort and the models for predicting or evaluating thermal comfort during local heating.This paper would provide users with a guideline for choosing suitable heating equipment during winter.展开更多
The technology that waste activated carbon after extracting gold is regenerated with steam under microwave heating was studied. The influence of the activation temperature, activation duration and steam flow rate on i...The technology that waste activated carbon after extracting gold is regenerated with steam under microwave heating was studied. The influence of the activation temperature, activation duration and steam flow rate on iodine adsorption value and regeneration yield of activated carbon was investigated. The response surface methodology （RSM） technique was utilized to optimize the process conditions. The optimum conditions for the preparation of activated carbon are identified to be activation temperature of 831 ℃, activation duration of 40 min and steam flow rate of 2.67 mL/min. The optimum conditions result in an activated carbon with an iodine number of 1048 mg/g and a yield of 40%, and the BET surface area evaluated using nitrogen adsorption isotherm is 1493 m2/g, with total pore volume of 1.242 cm3/g. And the pore structure of activated carbon regenerated is mainly composed of micropores and a small amount of mesopores.展开更多
Nanofluids have attracted many scientists due to their remarkable thermophysical properties.Small percentage of nanoparticles when added to conventional fluid significantly enhances the heat transfer features.Sustaina...Nanofluids have attracted many scientists due to their remarkable thermophysical properties.Small percentage of nanoparticles when added to conventional fluid significantly enhances the heat transfer features.Sustainability and efficiency of nanomaterials have key role in the advancement of nanotechnology.This article analyzes the Hall,Ohmic heating and velocity slip effects on the peristalsis of nanofluid.Convective boundary conditions and heat generation/absorption are considered to facilitate the heat transfer characteristics.Governing equations for the peristaltic flow through a curved channel are derived in curvilinear coordinates.The equations are numerically solved under the assumption of long wavelength and small Reynold number.It has been observed that nanofluid enhances the heat transfer rate and reduces the fluid temperature.Hartman number and Hall parameter show reverse behavior in fluid motion and heat transfer characteristics.In the presence of velocity slip,the pressure gradient rapidly decreases and dominant effect is seen in narrow portion of channel.展开更多
In order to investigate Joule heating power,a three-dimensional finite element model(FEM) was developed to predict Joule heating power in the channels of double-loop inductor. The simulated results were compared with ...In order to investigate Joule heating power,a three-dimensional finite element model(FEM) was developed to predict Joule heating power in the channels of double-loop inductor. The simulated results were compared with experimental data from low load trials for a 400 kW inductor. The results,such as power factor and Joule heating power,show reasonable correlation with experimental data,and Joule heating rate reaches the maximum at the corners and the minimum at the centre of the cross-section area. With increasing relative permeability of iron core,length of coils,current frequency and resistivity of metal melt,the power factor and Joule heating power change. It is concluded that current frequency,the resistivity and length of the coil play a critical role in determining the power factor and Joule heating power,whereas relative permeability of the magnetic core shows no significant influence on them.展开更多
This paper presented a preliminary research on the central solar heating system with seasonal storage(CSHSSS)used in cold climate in China.A mathematical model of the solar energy seasonal storage water tank used in t...This paper presented a preliminary research on the central solar heating system with seasonal storage(CSHSSS)used in cold climate in China.A mathematical model of the solar energy seasonal storage water tank used in the central solar heating system was firstly developed based on energy conservation.This was followed by the simulation of the CSHSSS used in a two-floor villa in Harbin,and analysis of the impacts on storage water temperature of tank volume,solar collector area,tank burial depth,insulation thickness around the tank,etc.The results show there is a relatively economical tank volume to optimize the system efficiency,which decreases with increasing tank volume at the constant collector area,and increases with increasing collector area at the constant tank volume.Furthermore,the insulation thickness has obvious effect on avoiding heat loss,while the tank burial depth doesn't.In addition,the relationship between the solar collector efficiency and storage water temperature is also obtained,it decreases quickly with increasing storing water temperature,and then increases slowly after starting space heating system.These may be helpful for relevant design and optimization in cold climates in China and all over the world.展开更多
A district heating and hot water supply system is presented which synthetically utilizes geothermal energy,solar thermal energy and natural gas thermal energy.The multi-energy utilization system has been set at the ne...A district heating and hot water supply system is presented which synthetically utilizes geothermal energy,solar thermal energy and natural gas thermal energy.The multi-energy utilization system has been set at the new campus of Tianjin Polytechnic University(TPU),A couple of deep geothermal wells which are 2 300 m in depth were dug,Deep geothermal energy cascade utilization is achieved by two stages of plate heat exchangers(PHE) and two stages of water source heat pumps(WSHP).Shallow geothermal energy is used in assistant heating by two ground coupled heat pumps(GCHPs) with 580 vertical ground wells which are 120 m in depth.Solar thermal energy collected by vacuum tube arrays(VTAs) and geothermal energy are complementarily utilized to make domestic hot water.Superfluous solar energy can be stored in shallow soil for the GCHP utilization.The system can use fossil fuel thermal energy by two natural gas boilers(NGB) to assist in heating and making hot water.The heating energy efficiency was measured in the winter of 2010-2011.The coefficients of performance(COP) under different heating conditions are discussed.The performance of hot water production is tested in a local typical winter day and the solar thermal energy utilization factor is presented.The rusults show that the average system COP is 5.75 or 4.96 under different working conditions,and the typical solar energy utilization factor is 0.324.展开更多
Heating-only fan coil(HFC)is one of the suited end users,which is not only compact but also highly efficient.And the major factors affecting the heat dissipation performance of HFC include leakage through coil bypass,...Heating-only fan coil(HFC)is one of the suited end users,which is not only compact but also highly efficient.And the major factors affecting the heat dissipation performance of HFC include leakage through coil bypass,distance between fan and coil,fan structure and air inlet type.Under natural air convection or forced,experimental studies were made on the effects of these factors upon the heat dissipation performance of HFC.The results show that:1)After reducing the leakage through coil bypass,the heat dissipation of HFC increases 16.9%under natural convection,and increases 8.3%under forced convection.2)After the distance between fan and coil be raised from 23.2cm to 41.7cm,the heat dissipation of HFC decreases 21.3%under natural convection,but increases12.8%under forced convection.3)After changing the fan structure,the heat dissipation of HFC increases 41.8%under natural convection,and the heat dissipation per motor power increases 96.1%under forced convection.4)The heat dissipations of HFC with round pass,slit and strip type of air inlet are different,whose proportion is about 100%,110%,136%under natural convection,and 100%,105%,116%under forced convection.展开更多
Two-dimensional boundary layer flow of an incompressible third grade nanofluid over a stretching surface is investigated.Influence of thermophoresis and Brownian motion is considered in the presence of Newtonian heati...Two-dimensional boundary layer flow of an incompressible third grade nanofluid over a stretching surface is investigated.Influence of thermophoresis and Brownian motion is considered in the presence of Newtonian heating and viscous dissipation.Governing nonlinear problems of velocity, temperature and nanoparticle concentration are solved via homotopic procedure.Convergence is examined graphically and numerically. Results of temperature and nanoparticle concentration are plotted and discussed for various values of material parameters, Prandtl number, Lewis number, Newtonian heating parameter, Eckert number and thermophoresis and Brownian motion parameters. Numerical computations are performed. The results show that the change in temperature and nanoparticle concentration distribution functions is similar when we use higher values of material parameters β1 andβ2. It is seen that the temperature and thermal boundary layer thickness are increasing functions of Newtonian heating parameter γ.An increase in thermophoresis and Brownian motion parameters tends to an enhancement in the temperature.展开更多
The magnetohydrodynamic(MHD) three-dimensional flow of Jeffrey fluid in the presence of Newtonian heating is investigated. Flow is caused by a bidirectional stretching surface. Series solutions are constructed for the...The magnetohydrodynamic(MHD) three-dimensional flow of Jeffrey fluid in the presence of Newtonian heating is investigated. Flow is caused by a bidirectional stretching surface. Series solutions are constructed for the velocity and temperature fields. Convergence of series solutions is ensured graphically and numerically. The variations of key parameters on the physical quantities are shown and discussed in detail. Constructed series solutions are compared with the existing solutions in the limiting case and an excellent agreement is noticed. Nusselt numbers are computed with and without magnetic fields. It is observed that the Nusselt number decreases in the presence of magnetic field.展开更多
The peristaltic transport of viscous fluid in an asymmetric channel is concentrated. The channel walls exhibit convective boundary conditions. Both cases of hydrodynamic and magnetohydrodynamic(MHD) fluids are conside...The peristaltic transport of viscous fluid in an asymmetric channel is concentrated. The channel walls exhibit convective boundary conditions. Both cases of hydrodynamic and magnetohydrodynamic(MHD) fluids are considered. Mathematical analysis has been presented in a wave frame of reference. The resulting problems are non-dimensionalized. Long wavelength and low Reynolds number approximations are employed. Joule heating effect on the thermal equation is retained. Analytic solutions for stream function and temperature are constructed. Numerical integration is carried out for pressure rise per wavelength. Effects of influential flow parameters have been pointed out through graphs.展开更多
In order to understand the initial surface damage of Al piston in unsteady thermal environment like knock combustion,T6 heat treated cast Al-Si-Cu alloy was thermal shocked under different heating speeds between room ...In order to understand the initial surface damage of Al piston in unsteady thermal environment like knock combustion,T6 heat treated cast Al-Si-Cu alloy was thermal shocked under different heating speeds between room temperature and 450°C by adjusting the environmental temperature.The surface evolution was mainly characterized in view of roughness,hardness,morphology,texture,phase and element distribution.Results indicated that both the roughness and hardness went up to the maximum and then decreased with rising heating speed.Micro-structure and phase analysis suggested that the interactions of solid phase transition and oxidation with enhancing thermal stress took responsible for the surface evolution.展开更多
基金Projects(52108347, 52179112, 52178371) supported by the National Natural Science Foundation of ChinaProjects(2020C01147, 2023C01165) supported by the Primary Research and Development Plan of Zhejiang Province,ChinaProject(LQ22E080010) supported by the Outstanding Youth Project of Natural Science Foundation of Zhejiang Province,China。
文摘When the interface of a multilayered saturated soil is rough with noticeable gaps, heat flow lines converge towards the actual contact points, causing thermal flow contraction. Conversely, in the interface between two layers of soil with different properties, pore water flows slowly along the pore channels, demonstrating laminar flow phenomenon. To predict the thermal contact resistance and flow contact resistance at the interface, this paper constructs general imperfect thermal contact model and general imperfect flow contact model, respectively. Utilizing a thermo-hydro- mechanical coupling model, the thermal consolidation behavior of multilayered saturated soil under two-dimensional conditions is investigated. Fourier and Laplace transformations are applied to decouple the governing equations, yielding expressions for the temperature increment, pore water pressure, and displacement in multilayered saturated soil. The inverse Fourier-Laplace transformation is then used to obtain numerical solutions, which are compared with degeneration solutions to validate the computational accuracy. The differences in the thermal consolidation process under various thermal contact and flow contact resistance models are discussed. Furthermore, the impact of parameters such as the thermal resistance coefficient, partition thermal contact coefficient, flow contact resistance coefficient, and partition flow contact coefficient on thermal consolidation are investigated. Results indicate that thermal contact resistance creates a relative thermal gradient at the interface, leading to increased pore water pressure and reduced displacement nearby. In contrast, flow contact resistance generates a relative pore pressure gradient at the interface, resulting in increased displacement within the saturated soil with minimal effect on temperature increment distribution.
基金Project(2017JM5077)supported by the Natural Science Basic Research Plan in Shaanxi Province,ChinaProjects(300102259109,300102259306)supported by the Fundamental Research Funds for the Central Universities,China。
文摘Asphalt mixture pavement reheating is one of the important steps in hot in-place recycling(HIR).To improve the heating speed of asphalt pavement in HIR,based on the numerical analysis model of asphalt mixture heating process,a new multi-layer low-temperature heating method(MLHM)was proposed.Considering input heat flux,the thermal capacity and thermal resistance of asphalt mixture,the heat transfer model was established based on energy conservation law.By heating the asphalt mixture in layers,it changes the situation that the heat energy can only be input from the upper surface of the asphalt mixture pavement.Through the simulation of the heating method of asphalt mixture in the existing technology,the result shows that the existing heating methods lead to serious aging or charring of the asphalt mixture.By MLHM,the upper and the bottom of the asphalt mixture are heated at the same time,and the heating temperature is lower than other heat methods,which not only reduces the heating thickness and increases the heating area of the asphalt mixture pavement,but also improves the heating speed,saves the energy resource and ensures the heating quality.Especially,by MLHM,the heating uniformity is better and speed is faster.
基金Project(50474083) supported by the National Natural Science Foundation of ChinaProject supported by the Baoshan Iron & Steel Co. Ltd. of China
文摘Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the conditions of COFCC with n(O)-n(C) (molar ratio) as 1.00-0.84 and n(SiO2)-n(CaO) as 1.00-0.39, the samples were heated by 10 kW microwave power to reach the given temperatures and held for different times respectively. The results show that the low-C-Cr ferrochromium metal phase in the reduced materials forms before the high-C-Cr ferrochromium metal phase does. With increasing temperature the C content of ferrochromium metals is in a positive correlation with the content of Cr. The C content of ferrochromium metal in reduced materials is 0-10.07% with an average value of 4.68%. With the increase of holding time the Cr content in ferrochromium metals is in a negative correlation with the content of C, while the content of Fe changes in the contrary way. In the microwave field the kinetic conditions of carburization are closely related with the temperature of microwave heating, holding time and carbon fitting ratio.
基金Project(51090385) supported by the National Natural Science Foundation of ChinaProject(2001IB001) supported by Yunnan Provincial Science and Technology Fund, China
文摘Double self-adaptive fuzzy PID algorithm-based control strategy was proposed to construct quasi-cascade control system to control the speed of the acid-pickling process of titanium plates and strips. It is very useful in overcoming non-linear dynamic behavior, uncertain and time-varying parameters, un-modeled dynamics, and couples between the automatic turbulence control (ATC) and the automatic acid temperature control (AATC) with varying parameters during the operation process. The quasi-cascade control system of inner and outer loop self-adaptive fuzzy PID controller was built, which could effectively control the pickling speed of plates and strips. The simulated results and real application indicate that the plates and strips acid pickling speed control system has good performances of adaptively tracking the parameter variations and anti-disturbances, which ensures the match of acid pickling temperature and turbulence of flowing with acid pickling speed, improving the surface quality of plates and strips acid pickling, and energy efficiency.
基金Project(KKSY201503006)supported by Scientific Research Foundation of Kunming University of Science and Technology,ChinaProject(2014FD009)supported by the Applied Basic Research Foundation(Youth Program)of ChinaProject(51090385)supported by the National Natural Science Foundation of China
文摘The exothermic efficiency of microwave heating an electrolyte/water solution is remarkably high due to the dielectric heating by orientation polarization of water and resistance heating by the Joule process occurred simultaneously compared with pure water.A three-dimensional finite element numerical model of multi-feed microwave heating industrial liquids continuously flowing in a meter-scale circular tube is presented.The temperature field inside the applicator tube in the cavity is solved by COMSOL Multiphysics and professional programming to describe the momentum,energy and Maxwell's equations.The evaluations of the electromagnetic field,the temperature distribution and the velocity field are simulated for the fluids dynamically heated by singleand multi-feed microwave system,respectively.Both the pilot experimental investigations and numerical results of microwave with single-feed heating for fluids with different effective permittivity and flow rates show that the presented numerical modeling makes it possible to analyze dynamic process of multi-feed microwave heating the industrial liquid.The study aids in enhancing the understanding and optimizing of dynamic process in the use of multi-feed microwave heating industrial continuous flow for a variety of material properties and technical parameters.
文摘In this paper,the performance of a solar thermal system with a focus on space heating was investigated.A 70 m^(2) detached house was considered in the weather conditions of the city of Tehran,Iran.A thermosyphon solar water heater with a flat plate collector combined with an auxiliary electrical heater supplies the heating demand of the house.The proposed system was modeled and analyzed using TRNSYS software.In this regard,the TRNBuild module was employed for the building load calculation.The model has been simulated for one year of operation.The effects of the solar collector’s surface area and storage volume were assessed.The results show that for a solar collector with a 15 m^(2) surface area,the solar fraction is 0.29 in January,during which the solar radiation is the lowest.Using solar collectors of10 m^(2) and 5 m^(2) surface areas,the solar fraction falls to 0.23 and 0.14,respectively in January.Besides,two cases of 150 L and 300 L storage tanks are taken into account.Eventually,it is found that using a 15 m^(2) solar collector and a 150 L storage tank can appropriately provide the building’ s heating demand taking the thermal performance and economic aspects into consideration.
基金Project(hx2013-87)supported by the Qingdao Economic and Technology Development Zone Haier Water-Heater Co.Ltd.,China
文摘In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1400-2600 r/min）, ambient air temperature（2.4-17.8 ℃） and condenser water inlet temperature（30-50℃）. The results show that as engine speed increases from 1400 r/min to 2600 r/min, the total heating capacity and energy consumption increase by about 30% and 89%, respectively; while the heat pump coefficient of performance（COP） and system primary energy ratio（PER） decrease by 44% and 31%, respectively. With the increase of ambient air temperature from 2.4 ℃ to 17.8 ℃, the heat pump COP and system PER increase by 32% and 19%, respectively. Moreover, the heat pump COP and system PER decrease by 27% and 15%, respectively, when the condenser water inlet temperature changes from 30 ℃ to 50 ℃. So, it is obvious that the effect of engine speed on the performance is more significant than the effects of ambient air temperature and condenser water inlet temperature.
基金Project(NCET-04-0748)supported by the New Century Excellent Talent Planning of China
文摘A new iron-making process using carburized pre-reduced iron ore pellets and microwave heating is investigated. The pre-reduced pellets, with a porous structure, and fine particles are carburized homogeneously at 400-650 ℃ in a CO atmosphere. The carburized carbon not only acts reaction as a reduction agent, but also absorbs microwave in the reduction process. Hence, the carburized pre-reduced pellets can be rapidly reduced by microwave heating. There are three procedures involved in the process, namely, gas-based pre-reduction, low-temperatttre carburization and deep reduction by microwave heating. Carburized pre-reduced iron ore pellets show a rapid temperature rise that is twice as fast as the results for pre-reduced pellets in the laboratory. This not only improves the efficiency of the microwave heating, but also accelerates the reduction of iron oxides. The temperature of the pre-reduced pellets rises to 1050 ℃ in 45 min when the carburization rate is 2.02%, and the metallization rate and compressive strength reach 94.24% and 1725 N/pellet, respectively.
基金Project(51875122)supported by the National Natural Science Foundation of China
文摘The resistance heating method has been one of the prospective techniques for hot processing and welding techniques. The thermal behavior under different densities of electric current and the effect of electric current at temperature of 780 oC using low density of electric current of 6.70 A/mm^2 on the B2+O lamellar microstructure were investigated for Ti2AlNb alloy sheet. The stable temperature denoted a balanced state between the Joule heat and the dissipation of heat including heat conduction, convection and radiation while the distribution of temperature was nonuniform. The highest temperatures of electric current heating samples increased as the density of electric current was elevated. In order to understand the specific effect of electric current on B2+O microstructure, heat treatment for microstructural homogeneity was introduced to this study. After that, according to the microstructural observations by common characterization techniques in the resistance-heating sample and the isothermal furnace-heating sample after homogenizing treatment, few significant differences in content and orientation of phases can be directly and explicitly found except the thermal effect from the applied electric current. The results will provide reference to this prospective forming and welding techniques and the application for Ti2AlNb alloys using resistance heating in the near future.
基金Projects(51978661,51778625)supported by the National Natural Science Foundation of ChinaProject(ACSKL2018KT12)supported by State Key Laboratory of Air-conditioning Equipment and System Energy Conservation,China。
文摘Personal conditioning system(PCS)is receiving considerable attention due to its energy-saving potential and the ability to satisfy individual comfort requirements.As a part of PCS,personal heating systems can maintain human thermal comfort in cold environments,which leads to their potential role of important heating mode in cold winter,especially in the Hot Summer and Cold Winter regions of China.In order to better promote the development and application of personal heating systems,this paper reviews the published studies.Personal heating systems can be divided into four types based on the mode of heat transfer:conductive,convective,radiative and combinative type.Characteristics of each category and respective devices are introduced.Furthermore,identifying the effects of personal heating on thermal comfort and the models for predicting or evaluating thermal comfort during local heating.This paper would provide users with a guideline for choosing suitable heating equipment during winter.
基金Project(2013AA064003)supported by the National High Technology Research and Development Program of ChinaProject(2012HB008)supported by Young and Middle-aged Academic Technology Leader Backup Talent Cultivation Program in Yunnan Province,China
文摘The technology that waste activated carbon after extracting gold is regenerated with steam under microwave heating was studied. The influence of the activation temperature, activation duration and steam flow rate on iodine adsorption value and regeneration yield of activated carbon was investigated. The response surface methodology （RSM） technique was utilized to optimize the process conditions. The optimum conditions for the preparation of activated carbon are identified to be activation temperature of 831 ℃, activation duration of 40 min and steam flow rate of 2.67 mL/min. The optimum conditions result in an activated carbon with an iodine number of 1048 mg/g and a yield of 40%, and the BET surface area evaluated using nitrogen adsorption isotherm is 1493 m2/g, with total pore volume of 1.242 cm3/g. And the pore structure of activated carbon regenerated is mainly composed of micropores and a small amount of mesopores.
文摘Nanofluids have attracted many scientists due to their remarkable thermophysical properties.Small percentage of nanoparticles when added to conventional fluid significantly enhances the heat transfer features.Sustainability and efficiency of nanomaterials have key role in the advancement of nanotechnology.This article analyzes the Hall,Ohmic heating and velocity slip effects on the peristalsis of nanofluid.Convective boundary conditions and heat generation/absorption are considered to facilitate the heat transfer characteristics.Governing equations for the peristaltic flow through a curved channel are derived in curvilinear coordinates.The equations are numerically solved under the assumption of long wavelength and small Reynold number.It has been observed that nanofluid enhances the heat transfer rate and reduces the fluid temperature.Hartman number and Hall parameter show reverse behavior in fluid motion and heat transfer characteristics.In the presence of velocity slip,the pressure gradient rapidly decreases and dominant effect is seen in narrow portion of channel.
基金Project(50876116) supported by the National Natural Science Foundation of ChinaProject(2007CK3077) supported by Innovative Program of Hunan Science and Technology AgencyProject(1343-77225) supported by the Graduate School of Central South University
文摘In order to investigate Joule heating power,a three-dimensional finite element model(FEM) was developed to predict Joule heating power in the channels of double-loop inductor. The simulated results were compared with experimental data from low load trials for a 400 kW inductor. The results,such as power factor and Joule heating power,show reasonable correlation with experimental data,and Joule heating rate reaches the maximum at the corners and the minimum at the centre of the cross-section area. With increasing relative permeability of iron core,length of coils,current frequency and resistivity of metal melt,the power factor and Joule heating power change. It is concluded that current frequency,the resistivity and length of the coil play a critical role in determining the power factor and Joule heating power,whereas relative permeability of the magnetic core shows no significant influence on them.
基金Supported by Multi-Discipline Scientific Rearch Foundation of Harbin Institute of Technology(HIT MD2003.1)Postdoctoral Scientific Rearch Foundation of Heilongjiang Provine(LBH-Q06066)
文摘This paper presented a preliminary research on the central solar heating system with seasonal storage(CSHSSS)used in cold climate in China.A mathematical model of the solar energy seasonal storage water tank used in the central solar heating system was firstly developed based on energy conservation.This was followed by the simulation of the CSHSSS used in a two-floor villa in Harbin,and analysis of the impacts on storage water temperature of tank volume,solar collector area,tank burial depth,insulation thickness around the tank,etc.The results show there is a relatively economical tank volume to optimize the system efficiency,which decreases with increasing tank volume at the constant collector area,and increases with increasing collector area at the constant tank volume.Furthermore,the insulation thickness has obvious effect on avoiding heat loss,while the tank burial depth doesn't.In addition,the relationship between the solar collector efficiency and storage water temperature is also obtained,it decreases quickly with increasing storing water temperature,and then increases slowly after starting space heating system.These may be helpful for relevant design and optimization in cold climates in China and all over the world.
基金Project(2010DFA72740-06) supported by International Science & Technology Cooperation Program of China
文摘A district heating and hot water supply system is presented which synthetically utilizes geothermal energy,solar thermal energy and natural gas thermal energy.The multi-energy utilization system has been set at the new campus of Tianjin Polytechnic University(TPU),A couple of deep geothermal wells which are 2 300 m in depth were dug,Deep geothermal energy cascade utilization is achieved by two stages of plate heat exchangers(PHE) and two stages of water source heat pumps(WSHP).Shallow geothermal energy is used in assistant heating by two ground coupled heat pumps(GCHPs) with 580 vertical ground wells which are 120 m in depth.Solar thermal energy collected by vacuum tube arrays(VTAs) and geothermal energy are complementarily utilized to make domestic hot water.Superfluous solar energy can be stored in shallow soil for the GCHP utilization.The system can use fossil fuel thermal energy by two natural gas boilers(NGB) to assist in heating and making hot water.The heating energy efficiency was measured in the winter of 2010-2011.The coefficients of performance(COP) under different heating conditions are discussed.The performance of hot water production is tested in a local typical winter day and the solar thermal energy utilization factor is presented.The rusults show that the average system COP is 5.75 or 4.96 under different working conditions,and the typical solar energy utilization factor is 0.324.
基金Supported by National11th Five-Year Plan Major Scientific and Technological Issues of China(2006BAJ01A04)
文摘Heating-only fan coil(HFC)is one of the suited end users,which is not only compact but also highly efficient.And the major factors affecting the heat dissipation performance of HFC include leakage through coil bypass,distance between fan and coil,fan structure and air inlet type.Under natural air convection or forced,experimental studies were made on the effects of these factors upon the heat dissipation performance of HFC.The results show that:1)After reducing the leakage through coil bypass,the heat dissipation of HFC increases 16.9%under natural convection,and increases 8.3%under forced convection.2)After the distance between fan and coil be raised from 23.2cm to 41.7cm,the heat dissipation of HFC decreases 21.3%under natural convection,but increases12.8%under forced convection.3)After changing the fan structure,the heat dissipation of HFC increases 41.8%under natural convection,and the heat dissipation per motor power increases 96.1%under forced convection.4)The heat dissipations of HFC with round pass,slit and strip type of air inlet are different,whose proportion is about 100%,110%,136%under natural convection,and 100%,105%,116%under forced convection.
基金funded by the Deanship of Scientific Research (DSR), King Abdulaziz University (KAU), under Grant No. 37-130-35-HiCi
文摘Two-dimensional boundary layer flow of an incompressible third grade nanofluid over a stretching surface is investigated.Influence of thermophoresis and Brownian motion is considered in the presence of Newtonian heating and viscous dissipation.Governing nonlinear problems of velocity, temperature and nanoparticle concentration are solved via homotopic procedure.Convergence is examined graphically and numerically. Results of temperature and nanoparticle concentration are plotted and discussed for various values of material parameters, Prandtl number, Lewis number, Newtonian heating parameter, Eckert number and thermophoresis and Brownian motion parameters. Numerical computations are performed. The results show that the change in temperature and nanoparticle concentration distribution functions is similar when we use higher values of material parameters β1 andβ2. It is seen that the temperature and thermal boundary layer thickness are increasing functions of Newtonian heating parameter γ.An increase in thermophoresis and Brownian motion parameters tends to an enhancement in the temperature.
文摘The magnetohydrodynamic(MHD) three-dimensional flow of Jeffrey fluid in the presence of Newtonian heating is investigated. Flow is caused by a bidirectional stretching surface. Series solutions are constructed for the velocity and temperature fields. Convergence of series solutions is ensured graphically and numerically. The variations of key parameters on the physical quantities are shown and discussed in detail. Constructed series solutions are compared with the existing solutions in the limiting case and an excellent agreement is noticed. Nusselt numbers are computed with and without magnetic fields. It is observed that the Nusselt number decreases in the presence of magnetic field.
基金support from Higher Education Commission (HEC) of Pakistan through Ph.D Indigeous Scheme.
文摘The peristaltic transport of viscous fluid in an asymmetric channel is concentrated. The channel walls exhibit convective boundary conditions. Both cases of hydrodynamic and magnetohydrodynamic(MHD) fluids are considered. Mathematical analysis has been presented in a wave frame of reference. The resulting problems are non-dimensionalized. Long wavelength and low Reynolds number approximations are employed. Joule heating effect on the thermal equation is retained. Analytic solutions for stream function and temperature are constructed. Numerical integration is carried out for pressure rise per wavelength. Effects of influential flow parameters have been pointed out through graphs.
基金Project(DLBF2018-KY-JS-066-J)supported by the China North Engine Research InstituteProject(51902239)supported by the National Natural Science Foundation of China+3 种基金Project(2020JQ-808)supported by the Science and Technology Fund of Shaanxi Province,ChinaProjects(19JK0400,19JK0402)supported by the Education Fund of Shaanxi Province,ChinaProject(S202010702070)supported by the Innovation and Entrepreneurship Training Program for College Students,ChinaProject supported by the Youth Innovation Team of Shaanxi Universities:Metal Corrosion Protection and Surface Engineering Technology,China。
文摘In order to understand the initial surface damage of Al piston in unsteady thermal environment like knock combustion,T6 heat treated cast Al-Si-Cu alloy was thermal shocked under different heating speeds between room temperature and 450°C by adjusting the environmental temperature.The surface evolution was mainly characterized in view of roughness,hardness,morphology,texture,phase and element distribution.Results indicated that both the roughness and hardness went up to the maximum and then decreased with rising heating speed.Micro-structure and phase analysis suggested that the interactions of solid phase transition and oxidation with enhancing thermal stress took responsible for the surface evolution.
