The measurement of the surface quality and the profile preciseness is major issues in many industrial branches such that the surface quality of semi products directly affects the subsequent production steps.Although,t...The measurement of the surface quality and the profile preciseness is major issues in many industrial branches such that the surface quality of semi products directly affects the subsequent production steps.Although,there are many ways to obtain required data,the hardware necessary for the measurements such as 2D or 3D scanners,depending on the problem’s complexity,is too expensive.Therefore,in this paper,what we put forward as a novelty is an algorithm which is verified on the model of simple 3D scanner on the image processing basis with the resolution of 0.1 mm.There are many ways to scan surface profile;however,the image processing currently is the most trending topic in industry automation.Most importantly,in order to obtain surface images,standard high resolution reflex camera is used and thus the post processing could be realized with MatLab as the software environment.Therefore,this solution is an alternative to the expensive scanners,and single-purpose devices could be extended by many additional functions.展开更多
The influence of three factors, such as volume percentage of reinforcement particles(i.e. Al2O3), tool tilt angle and concave angle of shoulder, on the mechanical properties of Cue Al2O3 surface composites fabricated ...The influence of three factors, such as volume percentage of reinforcement particles(i.e. Al2O3), tool tilt angle and concave angle of shoulder, on the mechanical properties of Cue Al2O3 surface composites fabricated via friction stir processing was studied. Taguchi method was used to optimize these factors for maximizing the mechanical properties of surface composites. The fabricated surface composites were examined by optical microscope for dispersion of reinforcement particles. It was found that Al2O3 particles are uniformly dispersed in the stir zone. The tensile properties of the surface composites increased with the increase in the volume percentage of the Al2O3 reinforcement particles.This is due to the addition of the reinforcement particles which increases the temperature of recrystallization by pinning the grain boundaries of the copper matrix and blocking the movement of the dislocations. The observed mechanical properties are correlated with microstructure and fracture features.展开更多
A new method to detect steel ball's surface flaws is presented based on computer techniques of image processing and pattern recognition. The steel ball's surface flaws is the primary factor causing bearing fai...A new method to detect steel ball's surface flaws is presented based on computer techniques of image processing and pattern recognition. The steel ball's surface flaws is the primary factor causing bearing failure. The high efficient and precision detections for the surface flaws of steel ball can be conducted by the presented method, including spot, abrasion, burn, scratch and crack, etc. The design of main components of the detecting system is described in detail including automatic feeding mechanism, automatic spreading mechanism of steel ball's surface, optical system of microscope, image acquisition system, image processing system. The whole automatic system is controlled by an industrial control computer, which can carry out the recognition of flaws of steel ball's surface effectively.展开更多
An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the ma...An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the main stress trajectories as the representation of force flows on a free-form surface,an automatic grid generation approach is proposed for the architectural design.The algorithm automatically plots the main stress trajectories on a 3D free-form surface,and adopts a modified advancing front meshing technique to generate the structural grid.Based on the proposed algorithm,an automatic grid generator named "St-Surmesh" is developed for the practical architectural design of free-form surface structure.The surface geometry of one of the Sun Valleys in Expo Axis for the Expo Shanghai 2010 is selected as a numerical example for validating the proposed approach.Comparative studies are performed to demonstrate how different structural grids affect the design of a free-form surface structure.展开更多
With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu c...With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu ctive materials away and polishes work-piece of free-form surface. The study o f the contact force between the end of polishing tool and the surface of work-p iece is the key for the compliant EDM to study its cutting mechanism and to make better use of it. This paper makes a model for the contact force and verifies i t by experiments and simulation based on the theory of elastic body kinetics and dynamic stress concentration. The research work shows that this contact force i s caused by both the electrical impulsion of EDM and the mechanical force of ult rasonic vibration, the discharge frequency of compliant EDM has a much more clos er connection with the vibration frequency of polishing tool rather than the fre quency of ultrasonic vibration.展开更多
The aim of present study is to analyze the influence of volume percentage(vol.%) of nano-sized particles(TiB_2: average size is 35 nm) on microstructure, mechanical and tribological behavior of 6061-T6 Al alloy surfac...The aim of present study is to analyze the influence of volume percentage(vol.%) of nano-sized particles(TiB_2: average size is 35 nm) on microstructure, mechanical and tribological behavior of 6061-T6 Al alloy surface nano composite prepared via Friction stir process(FSP). The microstructure of the fabricated surface nanocomposites is examined using optical microscopy(OM) and scanning electron microscope(SEM) for distribution of TiB_2 nano reinforcement particles, thickness of nano composite layer formed on the Aluminum alloy substrate and fracture features. The depth of surface nano composite layer is measured as 3683.82 m m along the cross section of stir zone of nano composite perpendicular to FSP. It was observed that increase in volume percentage of TiB_2 particles, the microhardness is increased up to132 Hv and it is greater than as-received Al alloy's microhardness(104 Hv). It is also observed that at 4volume percentage higher tensile properties exhibited as compared with the 2 and 8 vol. %. It is found that high wear resistance exhibited at 4 volume percentage as-compared with the 2 and 8 vol. %. The observed wear and mechanical properties are interrelated with microstructure, fractography and worn morphology.展开更多
To reduce the fuel consumption and emissions and also enhance the molten aluminum quality, a mathematical model with user-developed melting model and burning capacity model, were established according to the features ...To reduce the fuel consumption and emissions and also enhance the molten aluminum quality, a mathematical model with user-developed melting model and burning capacity model, were established according to the features of melting process of regenerative aluminum melting furnaces. Based on validating results by heat balance test for an aluminum melting furnace, CFD （computational fluid dynamics） technique, in association with statistical experimental design were used to optimize the melting process of the aluminum melting furnace. Four important factors influencing the melting time, such as horizontal angle between burners, height-to-radius ratio, natural gas mass flow and air preheated temperature, were identified by PLACKETT-BURMAN design. A steepest descent method was undertaken to determine the optimal regions of these factors. Response surface methodology with BOX-BEHNKEN design was adopted to further investigate the mutual interactions between these variables on RSD （relative standard deviation） of aluminum temperature, RSD of furnace temperature and melting time. Multiple-response optimization by desirability function approach was used to determine the optimum melting process parameters. The results indicate that the interaction between the height-to-radius ratio and horizontal angle between burners affects the response variables significantly. The predicted results show that the minimum RSD of aluminum temperature （12.13%）, RSD of furnace temperature （18.50%） and melting time （3.9 h） could be obtained under the optimum conditions of horizontal angle between burners as 64°, height-to-radius ratio as 0.3, natural gas mass flow as 599 m3/h, and air preheated temperature as 639 ℃. These predicted values were further verified by validation experiments. The excellent correlation between the predicted and experimental values confirms the validity and practicability of this statistical optimum strategy.展开更多
Carrying out experiments and researches on tool bre ak age and undercut of work-piece of free-form surface by using wavelet analysis, both the fault features can be extracted in a special frequency segment of wave let...Carrying out experiments and researches on tool bre ak age and undercut of work-piece of free-form surface by using wavelet analysis, both the fault features can be extracted in a special frequency segment of wave let decompose. According to the feature of transient fault, the author proposes for the first time the automatic determination technology of the threshold by us e of the adaptive filter characteristic of wavelet transform. Based on profound researches on steady fault feature, this dissertation makes an effective token o f steady fault feature by using wavelet energy method, and proposes the new idea to identify cut-in case and cut-out case, thereby successfully gives an uniqu e description quantitatively on the characterization of the variation of fault a nd cutting condition in the monitoring system.展开更多
The heat treatable aluminum-copper alloy AA2014 finds wide application in the aerospace and defence industry due to its high strength-toweight ratio and good ductility. Friction stir welding(FSW) process, an emerging ...The heat treatable aluminum-copper alloy AA2014 finds wide application in the aerospace and defence industry due to its high strength-toweight ratio and good ductility. Friction stir welding(FSW) process, an emerging solid state joining process, is suitable for joining this alloy compared to fusion welding processes. This work presents the formulation of a mathematical model with process parameters and tool geometry to predict the responses of friction stir welds of AA 2014-T6 aluminum alloy, viz yield strength, tensile strength and ductility. The most influential process parameters considered are spindle speed, welding speed, tilt angle and tool pin profile. A four-factor, five-level central composite design was used and a response surface methodology(RSM) was employed to develop the regression models to predict the responses.The mechanical properties, such as yield strength(YS), ultimate tensile strength(UTS) and percentage elongation(%El), are considered as responses. Method of analysis of variance was used to determine the important process parameters that affect the responses. Validation trials were carried out to validate these results. These results indicate that the friction stir welds of AA 2014-T6 aluminum alloy welded with hexagonal tool pin profile have the highest tensile strength and elongation, whereas the joints fabricated with conical tool pin profile have the lowest tensile strength and elongation.展开更多
A feasible method to improve the reliability and processing efficiency of large vibrating screen via the application of an elastic screen surface with multiple attached substructures （ESSMAS） was proposed. In the ES...A feasible method to improve the reliability and processing efficiency of large vibrating screen via the application of an elastic screen surface with multiple attached substructures （ESSMAS） was proposed. In the ESSMAS, every screen rod, with ends embedded into elastomer, is coupled to the main screen structure in a relatively flexible manner. The theoretical analysis was conducted, which consists of establishing dynamic model promoted from the fuzzy structure theory as well as calculating for the equivalent stiffness of each attached structure. According to the numerical simulation using the NEWMARK-fl integration method, this assembling pattern significantly leads to the screen surface/rod having larger vibration intensity than that of the corresponding position on screen structure, which specifically, with an averaged acceleration amplitude increasing ratio of 11.37% in theoretical analysis and 20.27% in experimental test. The experimental results, within a tolerant error, also confirm the established model and demonstrate the feasibility of ESSMAS.展开更多
High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Amon...High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160 μm sized boron carbide powder was procured and was reduced to 60 μm and 30 μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing.Ballistic performance testing as per the military standard(JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites was developed. This method was based on energy balance, i.e., the initial energy of impact is same as that of energy absorbed by multi layers. An attempt also has been made to validate the analytical results with the experimental findings. Variation between the analytical and experimental results may be accounted due to the assumptions considering such as isotropic behavior of target and shearing area of contact as cylindrical instead of conical interface As the analytical model yields the ballistic performance in the closer proximity of experimentally obtained, it can be considered to be an approximation to evaluate the ballistic performance of targets.展开更多
An attempt is made in the present study to obtain the relationships among process parameters and physical dimensions of AA6063 aluminium alloy coating on IS2062 mild steel obtained through friction surfacing and their...An attempt is made in the present study to obtain the relationships among process parameters and physical dimensions of AA6063 aluminium alloy coating on IS2062 mild steel obtained through friction surfacing and their impact on strength and ductility of the coating. Factorial experimental design technique was used to investigate and select the parameter combination to achieve a coating with adequate strength and ductility. Spindle speed, axial force and table traverse speed were observed to be the most significant factors on physical dimensions. It was observed that the thickness of the coating decreased as the coating width increased. In addition, the width and thickness of the coatings are higher at low and high torques. At intermediate torque values, when the force is high, the width of the coating is high, and its thickness is thin; and when the force is low, the width and thickness are low. The interaction effect between axial force(F)-table traverse speed(Vx) and spindle speed(N)-table traverse speed(Vx) produced an increasing effect on coating width and thickness, but other interactions exhibited decreasing influence. It has also been observed that sound coatings could be obtained in a narrow set of parameter range as the substrate-coating materials are metallurgically incompatible and have a propensity to form brittle intermetallics.展开更多
Researches on the processing method of ceramic bearing ball,the formation and propagation of defects in the manufacturing and the nondestructive evaluation(NDE) are summarized in this paper.The key for successful proc...Researches on the processing method of ceramic bearing ball,the formation and propagation of defects in the manufacturing and the nondestructive evaluation(NDE) are summarized in this paper.The key for successful processing of high strength ceramic balls is to avoid producing related defects.Many investigations show that the material microstructures,defects as well as mechanical processing parameters influence the final surface quality significantly.Most of NDE technologies,such as radiation,ultrasonic,dye-penetration and laser scatter,have been studied for ceramic bearing ball surface inspection around the world.So far,the difficulties to develop the perfect NDE system for ceramic bearing balls,which are caused by the defect variety and surface unfolding,have not been overcome yet.展开更多
基金Project(2102–2020)supported by the SPEV Project,University of Hradec Kralove,FIM,Czech RepublicProject(Vot-20H04)supported by Universiti Teknologi Malaysia(UTM)+1 种基金Project(Vot 4L876)supported by Malaysia Research University Network(MRUN)Project(Vot 5F073)supported by the Fundamental Research Grant Scheme(FRGS),Ministry of Education Malaysia。
文摘The measurement of the surface quality and the profile preciseness is major issues in many industrial branches such that the surface quality of semi products directly affects the subsequent production steps.Although,there are many ways to obtain required data,the hardware necessary for the measurements such as 2D or 3D scanners,depending on the problem’s complexity,is too expensive.Therefore,in this paper,what we put forward as a novelty is an algorithm which is verified on the model of simple 3D scanner on the image processing basis with the resolution of 0.1 mm.There are many ways to scan surface profile;however,the image processing currently is the most trending topic in industry automation.Most importantly,in order to obtain surface images,standard high resolution reflex camera is used and thus the post processing could be realized with MatLab as the software environment.Therefore,this solution is an alternative to the expensive scanners,and single-purpose devices could be extended by many additional functions.
文摘The influence of three factors, such as volume percentage of reinforcement particles(i.e. Al2O3), tool tilt angle and concave angle of shoulder, on the mechanical properties of Cue Al2O3 surface composites fabricated via friction stir processing was studied. Taguchi method was used to optimize these factors for maximizing the mechanical properties of surface composites. The fabricated surface composites were examined by optical microscope for dispersion of reinforcement particles. It was found that Al2O3 particles are uniformly dispersed in the stir zone. The tensile properties of the surface composites increased with the increase in the volume percentage of the Al2O3 reinforcement particles.This is due to the addition of the reinforcement particles which increases the temperature of recrystallization by pinning the grain boundaries of the copper matrix and blocking the movement of the dislocations. The observed mechanical properties are correlated with microstructure and fracture features.
基金Sponsored by Technology Project Itemof Department of Education of Jilin Province (2006JYT02)
文摘A new method to detect steel ball's surface flaws is presented based on computer techniques of image processing and pattern recognition. The steel ball's surface flaws is the primary factor causing bearing failure. The high efficient and precision detections for the surface flaws of steel ball can be conducted by the presented method, including spot, abrasion, burn, scratch and crack, etc. The design of main components of the detecting system is described in detail including automatic feeding mechanism, automatic spreading mechanism of steel ball's surface, optical system of microscope, image acquisition system, image processing system. The whole automatic system is controlled by an industrial control computer, which can carry out the recognition of flaws of steel ball's surface effectively.
基金Project(51378457)supported by the National Natural Science Foundation of China
文摘An essential step for the realization of free-form surface structures is to create an efficient structural gird that satisfies not only the architectural aesthetics,but also the structural performance.Employing the main stress trajectories as the representation of force flows on a free-form surface,an automatic grid generation approach is proposed for the architectural design.The algorithm automatically plots the main stress trajectories on a 3D free-form surface,and adopts a modified advancing front meshing technique to generate the structural grid.Based on the proposed algorithm,an automatic grid generator named "St-Surmesh" is developed for the practical architectural design of free-form surface structure.The surface geometry of one of the Sun Valleys in Expo Axis for the Expo Shanghai 2010 is selected as a numerical example for validating the proposed approach.Comparative studies are performed to demonstrate how different structural grids affect the design of a free-form surface structure.
文摘With an elastic negative pole being driven by ultra so nic vibration and being moved along the surface of work-piece compliantly by ro bot, a new kind of effective EDM, the compliant EDM, cuts the electrically condu ctive materials away and polishes work-piece of free-form surface. The study o f the contact force between the end of polishing tool and the surface of work-p iece is the key for the compliant EDM to study its cutting mechanism and to make better use of it. This paper makes a model for the contact force and verifies i t by experiments and simulation based on the theory of elastic body kinetics and dynamic stress concentration. The research work shows that this contact force i s caused by both the electrical impulsion of EDM and the mechanical force of ult rasonic vibration, the discharge frequency of compliant EDM has a much more clos er connection with the vibration frequency of polishing tool rather than the fre quency of ultrasonic vibration.
文摘The aim of present study is to analyze the influence of volume percentage(vol.%) of nano-sized particles(TiB_2: average size is 35 nm) on microstructure, mechanical and tribological behavior of 6061-T6 Al alloy surface nano composite prepared via Friction stir process(FSP). The microstructure of the fabricated surface nanocomposites is examined using optical microscopy(OM) and scanning electron microscope(SEM) for distribution of TiB_2 nano reinforcement particles, thickness of nano composite layer formed on the Aluminum alloy substrate and fracture features. The depth of surface nano composite layer is measured as 3683.82 m m along the cross section of stir zone of nano composite perpendicular to FSP. It was observed that increase in volume percentage of TiB_2 particles, the microhardness is increased up to132 Hv and it is greater than as-received Al alloy's microhardness(104 Hv). It is also observed that at 4volume percentage higher tensile properties exhibited as compared with the 2 and 8 vol. %. It is found that high wear resistance exhibited at 4 volume percentage as-compared with the 2 and 8 vol. %. The observed wear and mechanical properties are interrelated with microstructure, fractography and worn morphology.
基金Project(2009BSXT022) supported by the Dissertation Innovation Foundation of Central South University, ChinaProject(07JJ4016) supported by Natural Science Foundation of Hunan Province, ChinaProject(U0937604) supported by National Natural Science Foundation of China
文摘To reduce the fuel consumption and emissions and also enhance the molten aluminum quality, a mathematical model with user-developed melting model and burning capacity model, were established according to the features of melting process of regenerative aluminum melting furnaces. Based on validating results by heat balance test for an aluminum melting furnace, CFD （computational fluid dynamics） technique, in association with statistical experimental design were used to optimize the melting process of the aluminum melting furnace. Four important factors influencing the melting time, such as horizontal angle between burners, height-to-radius ratio, natural gas mass flow and air preheated temperature, were identified by PLACKETT-BURMAN design. A steepest descent method was undertaken to determine the optimal regions of these factors. Response surface methodology with BOX-BEHNKEN design was adopted to further investigate the mutual interactions between these variables on RSD （relative standard deviation） of aluminum temperature, RSD of furnace temperature and melting time. Multiple-response optimization by desirability function approach was used to determine the optimum melting process parameters. The results indicate that the interaction between the height-to-radius ratio and horizontal angle between burners affects the response variables significantly. The predicted results show that the minimum RSD of aluminum temperature （12.13%）, RSD of furnace temperature （18.50%） and melting time （3.9 h） could be obtained under the optimum conditions of horizontal angle between burners as 64°, height-to-radius ratio as 0.3, natural gas mass flow as 599 m3/h, and air preheated temperature as 639 ℃. These predicted values were further verified by validation experiments. The excellent correlation between the predicted and experimental values confirms the validity and practicability of this statistical optimum strategy.
文摘Carrying out experiments and researches on tool bre ak age and undercut of work-piece of free-form surface by using wavelet analysis, both the fault features can be extracted in a special frequency segment of wave let decompose. According to the feature of transient fault, the author proposes for the first time the automatic determination technology of the threshold by us e of the adaptive filter characteristic of wavelet transform. Based on profound researches on steady fault feature, this dissertation makes an effective token o f steady fault feature by using wavelet energy method, and proposes the new idea to identify cut-in case and cut-out case, thereby successfully gives an uniqu e description quantitatively on the characterization of the variation of fault a nd cutting condition in the monitoring system.
基金Financial assistance from Defence Research and Development Organization(DRDO)
文摘The heat treatable aluminum-copper alloy AA2014 finds wide application in the aerospace and defence industry due to its high strength-toweight ratio and good ductility. Friction stir welding(FSW) process, an emerging solid state joining process, is suitable for joining this alloy compared to fusion welding processes. This work presents the formulation of a mathematical model with process parameters and tool geometry to predict the responses of friction stir welds of AA 2014-T6 aluminum alloy, viz yield strength, tensile strength and ductility. The most influential process parameters considered are spindle speed, welding speed, tilt angle and tool pin profile. A four-factor, five-level central composite design was used and a response surface methodology(RSM) was employed to develop the regression models to predict the responses.The mechanical properties, such as yield strength(YS), ultimate tensile strength(UTS) and percentage elongation(%El), are considered as responses. Method of analysis of variance was used to determine the important process parameters that affect the responses. Validation trials were carried out to validate these results. These results indicate that the friction stir welds of AA 2014-T6 aluminum alloy welded with hexagonal tool pin profile have the highest tensile strength and elongation, whereas the joints fabricated with conical tool pin profile have the lowest tensile strength and elongation.
基金Projects(50574091,50774084) supported by the National Natural Science Foundation of China
文摘A feasible method to improve the reliability and processing efficiency of large vibrating screen via the application of an elastic screen surface with multiple attached substructures （ESSMAS） was proposed. In the ESSMAS, every screen rod, with ends embedded into elastomer, is coupled to the main screen structure in a relatively flexible manner. The theoretical analysis was conducted, which consists of establishing dynamic model promoted from the fuzzy structure theory as well as calculating for the equivalent stiffness of each attached structure. According to the numerical simulation using the NEWMARK-fl integration method, this assembling pattern significantly leads to the screen surface/rod having larger vibration intensity than that of the corresponding position on screen structure, which specifically, with an averaged acceleration amplitude increasing ratio of 11.37% in theoretical analysis and 20.27% in experimental test. The experimental results, within a tolerant error, also confirm the established model and demonstrate the feasibility of ESSMAS.
基金Financial assistance from Armament research board,New Delhi,India
文摘High strength-to-weight ratio of non-ferrous alloys, such as aluminium, magnesium and titanium alloys, are considered to be possible replacement of widely accepted steels in transportation and automobile sectors. Among these alloys, magnesium is self explosive and titanium is costlier, and aluminium is most likely to replace steels. Application of aluminium or its alloys is also thought of as an appropriate replacement in defence field, especially to enhance the easiness in mobility of combat vehicles while maintaining the same standard as that of conventional armour grade steels. Hence most of the investigations have been confined to aluminium or its alloys as base material and open an era of developing the newer composite materials to address the major limitation, i.e. tribological properties. The surface composites can be fabricated by incorporating the ceramic carbides like silicon carbide, carbides of transition metals and oxides of aluminium using surface modification techniques, such as high energy laser melt treatment, high energy electron beam irradiation and thermal spray process which are based on fusion route. These techniques yield the fusion related problems, such as interfacial reaction, pin holes, shrinkage cavities or voids and other casting related defects, and pave the way to need of an efficient technique which must be based on solid state. Recently developed friction stir processing technique was used in the present investigation for surface modification of AA7075 aluminum alloy, which is an alternative to steels. In the present investigation, 160 μm sized boron carbide powder was procured and was reduced to 60 μm and 30 μm using high energy ball mill. Subsequently these powders were used to fabricate the surface composites using friction stir processing.Ballistic performance testing as per the military standard(JIS.0108.01) was carried out. In the present work, an analytical method of predicting the ballistic behavior of surface composites was developed. This method was based on energy balance, i.e., the initial energy of impact is same as that of energy absorbed by multi layers. An attempt also has been made to validate the analytical results with the experimental findings. Variation between the analytical and experimental results may be accounted due to the assumptions considering such as isotropic behavior of target and shearing area of contact as cylindrical instead of conical interface As the analytical model yields the ballistic performance in the closer proximity of experimentally obtained, it can be considered to be an approximation to evaluate the ballistic performance of targets.
文摘An attempt is made in the present study to obtain the relationships among process parameters and physical dimensions of AA6063 aluminium alloy coating on IS2062 mild steel obtained through friction surfacing and their impact on strength and ductility of the coating. Factorial experimental design technique was used to investigate and select the parameter combination to achieve a coating with adequate strength and ductility. Spindle speed, axial force and table traverse speed were observed to be the most significant factors on physical dimensions. It was observed that the thickness of the coating decreased as the coating width increased. In addition, the width and thickness of the coatings are higher at low and high torques. At intermediate torque values, when the force is high, the width of the coating is high, and its thickness is thin; and when the force is low, the width and thickness are low. The interaction effect between axial force(F)-table traverse speed(Vx) and spindle speed(N)-table traverse speed(Vx) produced an increasing effect on coating width and thickness, but other interactions exhibited decreasing influence. It has also been observed that sound coatings could be obtained in a narrow set of parameter range as the substrate-coating materials are metallurgically incompatible and have a propensity to form brittle intermetallics.
基金the National Nature Science Foundation of China (50275031)
文摘Researches on the processing method of ceramic bearing ball,the formation and propagation of defects in the manufacturing and the nondestructive evaluation(NDE) are summarized in this paper.The key for successful processing of high strength ceramic balls is to avoid producing related defects.Many investigations show that the material microstructures,defects as well as mechanical processing parameters influence the final surface quality significantly.Most of NDE technologies,such as radiation,ultrasonic,dye-penetration and laser scatter,have been studied for ceramic bearing ball surface inspection around the world.So far,the difficulties to develop the perfect NDE system for ceramic bearing balls,which are caused by the defect variety and surface unfolding,have not been overcome yet.
