To investigate the process optimizationof Cu-en/AP composite microspheres preparation via electrostatic spraying,and to reveal the effects of droplet properties and flow rate variations on the experimental results dur...To investigate the process optimizationof Cu-en/AP composite microspheres preparation via electrostatic spraying,and to reveal the effects of droplet properties and flow rate variations on the experimental results during the electrostatic spraying process,the prepared process parameters of Cu-en/AP composite microspheres by electrostatic spray method under the orthogonal experimental design simulated by ANSYS(Fluent).The influence of flow rate,solvent ratio,and solid mass on the experimental results is examined using a controlled variable method.The results indicate that under the conditions of a flow rate of 2.67×10^(-3)kg/s an acetone-to-deionized water ratio of 1.5∶1.0,and a solid mass of 200 mg,the theoretical particle size of the composite microspheres can reach e nanoscale.Droplet trajectories in the electric field remain stable without significant deviation.The simulation results show that particle diameter decreases with increasing flow rate,with the trend leveling off around a flow rate of 1×10^(-3)kg/s.As the solvent ratio increases(with higher acetone content),particle diameter initially decreases,reaching a minimum around a ratio of 1.5∶1.0 before gradually increasing.Increasing the solid mass also reduces the particle diameter,with a linear increase in diameter observed at around 220 mg.Cu-en/AP composite microspheres with nanoscale dimensions were confirmed under these conditions by the final SEM images.展开更多
With the increasing importance of ocean exploitation,providing anti-rolling stability for ships at anchor has become more and more important.The lift-generation theory of traditional fin stabilizers is based on incomi...With the increasing importance of ocean exploitation,providing anti-rolling stability for ships at anchor has become more and more important.The lift-generation theory of traditional fin stabilizers is based on incoming flow velocity,which is not suitable for explaining lift generated at anchor.We analyzed non-steady flows,with forces on fin stabilizers generated by non-incoming flow velocity conditions,and gave a new lift-generation model.The correctness of the model was proven by comparing experimental results of fin stabilizer motion under non-incoming velocity conditions from the fluid computation software with that from the emulator of the lift-generation model.Finally,the model was used in an anti-rolling system on a ship and the reduction of roll was much better than what could be achieved by passive anti-rolling tanks.展开更多
The sleeve sealing ball seat is one of the important components in the multistage fracturing process of horizontal wells.The erosion and wear of the surface will decrease the sealing performance of the fracturing ball...The sleeve sealing ball seat is one of the important components in the multistage fracturing process of horizontal wells.The erosion and wear of the surface will decrease the sealing performance of the fracturing ball and the ball seat.This leads to pressure leakage during the fracturing process and fracturing failure.In this paper,combined with the actual ball seat materials and working conditions during the fracturing process,the erosion tests of ductile iron and tungsten carbide materials under different erosion speeds,angles,and mortar concentrations are carried out.Then the erosion test results were analyzed by mathematical fitting,and a set of erosion models suitable for sliding sleeve setting ball seat materials were innovatively established.For the first time,this paper combines the erosion model obtained from the experiment and the computational fluid dynamics(CFD)with Fluent software to simulate the erosion of the ball seat.Based on the simulation results,the morphology of the sliding sleeve seat ball after erosion is predicted.Through analysis of the test and simulation results,it is showed that the erosion rate of tungsten carbide material is lower and the wear resistance is better under the condition of small angle erosion.This research can offer a strong basis for fracturing site selection,surface treatment methods,and prediction of failure time of ball seats.展开更多
基金National Natural Science Foundation of China(No.2275150)。
文摘To investigate the process optimizationof Cu-en/AP composite microspheres preparation via electrostatic spraying,and to reveal the effects of droplet properties and flow rate variations on the experimental results during the electrostatic spraying process,the prepared process parameters of Cu-en/AP composite microspheres by electrostatic spray method under the orthogonal experimental design simulated by ANSYS(Fluent).The influence of flow rate,solvent ratio,and solid mass on the experimental results is examined using a controlled variable method.The results indicate that under the conditions of a flow rate of 2.67×10^(-3)kg/s an acetone-to-deionized water ratio of 1.5∶1.0,and a solid mass of 200 mg,the theoretical particle size of the composite microspheres can reach e nanoscale.Droplet trajectories in the electric field remain stable without significant deviation.The simulation results show that particle diameter decreases with increasing flow rate,with the trend leveling off around a flow rate of 1×10^(-3)kg/s.As the solvent ratio increases(with higher acetone content),particle diameter initially decreases,reaching a minimum around a ratio of 1.5∶1.0 before gradually increasing.Increasing the solid mass also reduces the particle diameter,with a linear increase in diameter observed at around 220 mg.Cu-en/AP composite microspheres with nanoscale dimensions were confirmed under these conditions by the final SEM images.
基金Supported by the National Natural Science Fundation of China under Grant No.50575048,No.50879012Heilongjiang Province Postdoctoral Science Foudation under Grant No.LBH-Z05052
文摘With the increasing importance of ocean exploitation,providing anti-rolling stability for ships at anchor has become more and more important.The lift-generation theory of traditional fin stabilizers is based on incoming flow velocity,which is not suitable for explaining lift generated at anchor.We analyzed non-steady flows,with forces on fin stabilizers generated by non-incoming flow velocity conditions,and gave a new lift-generation model.The correctness of the model was proven by comparing experimental results of fin stabilizer motion under non-incoming velocity conditions from the fluid computation software with that from the emulator of the lift-generation model.Finally,the model was used in an anti-rolling system on a ship and the reduction of roll was much better than what could be achieved by passive anti-rolling tanks.
基金This research was funded by the National Natural Science Foundation of China(grant number 51675534).
文摘The sleeve sealing ball seat is one of the important components in the multistage fracturing process of horizontal wells.The erosion and wear of the surface will decrease the sealing performance of the fracturing ball and the ball seat.This leads to pressure leakage during the fracturing process and fracturing failure.In this paper,combined with the actual ball seat materials and working conditions during the fracturing process,the erosion tests of ductile iron and tungsten carbide materials under different erosion speeds,angles,and mortar concentrations are carried out.Then the erosion test results were analyzed by mathematical fitting,and a set of erosion models suitable for sliding sleeve setting ball seat materials were innovatively established.For the first time,this paper combines the erosion model obtained from the experiment and the computational fluid dynamics(CFD)with Fluent software to simulate the erosion of the ball seat.Based on the simulation results,the morphology of the sliding sleeve seat ball after erosion is predicted.Through analysis of the test and simulation results,it is showed that the erosion rate of tungsten carbide material is lower and the wear resistance is better under the condition of small angle erosion.This research can offer a strong basis for fracturing site selection,surface treatment methods,and prediction of failure time of ball seats.
