Aim To design and experimentally study an 80C196KC-based SRD (switched re- luctance motor drive drive sytem) controller,Methods with the guidelines of the digitized SRD system controller,the circuit design and softwar...Aim To design and experimentally study an 80C196KC-based SRD (switched re- luctance motor drive drive sytem) controller,Methods with the guidelines of the digitized SRD system controller,the circuit design and software programming were completed,and a relevantexperimental system was PUT forward to test the newly designed controller.Result The experi-mental study showed that the newlydesigned controller had good speed-adjusting characteristicfor a switched reluctance motor ,its stable error was less than 5% and its full-load startingtime was shorter than 1.8s .Conclusion The new controller has reasonable circuit design and suitable controlling algorithm,and it is a feasible SRD system controller design scheme.展开更多
Theoretical analysis and field monitoring show that lateral vibration has very important effect on casing wear in deep & ultra-deep well drilling. The wear mechanism of casing under impact-sliding work conditions ...Theoretical analysis and field monitoring show that lateral vibration has very important effect on casing wear in deep & ultra-deep well drilling. The wear mechanism of casing under impact-sliding work conditions has been investigated and many experiments have been completed with a newly developed full-scale casing wear test machine. Test results present that adhesion wear, contact fatigue, and grinding abrasion are the main wear mechanisms under impact-sliding test conditions. The friction coefficient and linear wear rate of the casing rise obviously with an increase in impact load. And the larger the impact load, the rougher the worn surface of the casing. The linear wear rate decreased slightly but the average friction coefficient increased slightly with an increase in impact frequency under an impact load of 2,500 N. Both the linear wear rate of the casing and the average friction coefficient increased substantially with an increase in impact frequency under an impact load of 4,000 N. Under lower impact load conditions, grinding abrasion and contact fatigue are the main mechanisms of casing wear; under higher impact load conditions, adhesion wear and contact fatigue are the main mechanisms of casing wear.展开更多
This paper presented the results of an experimental investigation into the resistance performance of a wave-piercing trimaran with three alternative side hull forms,including asymmetric inboard,asymmetric outboard,and...This paper presented the results of an experimental investigation into the resistance performance of a wave-piercing trimaran with three alternative side hull forms,including asymmetric inboard,asymmetric outboard,and symmetric at various stagger/separation positions.Model tests were carried out at the National Iranian Marine Laboratory(NIMALA)towing tank using a scale model of a trimaran at the Froude numbers from 0.225 to 0.60.Results showed that by moving the side hulls to the forward of the main hull transom,the total resistance coefficient of trimaran decreased.Findings,furthermore,demonstrated that the symmetry shape of the side hull had the best performance on total resistance among three side hull forms.Results of this study are useful for selecting the side hull configuration from the resistance viewpoint.展开更多
Effective control of hypersonic transition is essential.In order to avoid affecting the structural proflle of the aircraft,as well as reducing power consumption and electromagnetic interference,a low-frequency surface...Effective control of hypersonic transition is essential.In order to avoid affecting the structural proflle of the aircraft,as well as reducing power consumption and electromagnetic interference,a low-frequency surface arc plasma disturbance experiment to promote hypersonic transition was carried out in theΦ0.25 m double-throat Ludwieg tube wind tunnel at Huazhong University of Science and Technology.Contacting printed circuit board sensors and non-contact focused laser differential interferometry testing technology were used in combination.Experimental results showed that the low-frequency surface arc plasma actuation had obvious stimulation effects on the second-mode unstable wave and could promote boundary layer transition by changing the spectral characteristics of the second-mode unstable wave.At the same time,the plasma actuation could promote energy exchange between the second-mode unstable wave and other unstable waves.Finally,the corresponding control mechanism is discussed.展开更多
Usually, the electrical breakdown of dielectric barrier discharge (DBD) at atmo-spheric pressure leads to a filamentary non-homogeneous discharge. However, it is also possible to obtain a diffuse DBD in homogeneous fo...Usually, the electrical breakdown of dielectric barrier discharge (DBD) at atmo-spheric pressure leads to a filamentary non-homogeneous discharge. However, it is also possible to obtain a diffuse DBD in homogeneous form, called atmospheric pressure glow discharge (APGD). We obtained a uniform APGD in helium and in the mixture of argon with alcohol, and studied the electrical characteristics of helium APGD. It is found that the relationship between discharge current and source frequency is different depending on the difference in gas gap when the applied voltage is kept constant. The discharge current shows an increasing trend with the increased frequency when gas gap is 0.8 cm, but the discharge current tends to decrease with the increased frequency when the gas gap increases. The discharge current always increases with the increased applied voltage when the source frequency is kept constant. We also observed a glow-like discharge in nitrogen at atmospheric pressure.展开更多
The investigation of beta-delayed proton decay mode has become a powerful probe to study the proton-rich nuclei and their nuc/eax structure. To study exotic nuclei with extremely low purity produced by the Radioactive...The investigation of beta-delayed proton decay mode has become a powerful probe to study the proton-rich nuclei and their nuc/eax structure. To study exotic nuclei with extremely low purity produced by the Radioactive Ion Beam Line in Lanzhou, we perform an experiment of beta-delayed proton emission of 36,37^Ca under a high-intensity continuous-beam mode. Ions are implanted into a double-sided silicon strip detector, where the subsequent decays are correlated to the preceding implantations in time sequence. The energy spectra of delayed protons from 36,37^Caβ decay, half-lives and decay branching ratios axe measured. The experimental results confirm the previous literature data and some improved results are obtained as well, demonstrating the feasibility of our detection approach and the reliability of our data analysis procedure. This allows for the development of more powerful detection arrays and further research on nuclei closer to proton-drip line on the basis of present work.展开更多
A coaxial multi-gap multi-channel spark switch with stainless-steel-spring ring gap electrodes is designed and investigated. The switch is triggered by a pulse applied to the cylindrical electrode outside the discharg...A coaxial multi-gap multi-channel spark switch with stainless-steel-spring ring gap electrodes is designed and investigated. The switch is triggered by a pulse applied to the cylindrical electrode outside the discharging channel through a parasitic capacitance coupling. The jitter of the switch is reduced by several short-distance gas gaps in series, and its inductance is reduced by a multi-channel discharge on account of the inductance isolation between the coils of the spring ring electrode. The experimental results indicate that the switch is of low inductance (15-30 nH), low jitter (-3 ns), and stable breakdown performance展开更多
A 10 J, 4o us XeCl laser interaction with LY12 aluminum and optical glass K9 targets is reported. The properties of laser-produced plasma (LPP) are analyzed. As a result, some parameters such as plasma ignition thresh...A 10 J, 4o us XeCl laser interaction with LY12 aluminum and optical glass K9 targets is reported. The properties of laser-produced plasma (LPP) are analyzed. As a result, some parameters such as plasma ignition threshold and plasma plume expansion velocity are obtained. Also, Laser induced pulse on irradiated targets are given.展开更多
The compression stroke characteristics of free-piston engine generator were studied. The numerical model of the compression stroke was established based on thermodynamics and dynamics equation,and the leak loss,heat l...The compression stroke characteristics of free-piston engine generator were studied. The numerical model of the compression stroke was established based on thermodynamics and dynamics equation,and the leak loss,heat loss and friction loss were considered. Through solving numerical equations,the in-cylinder pressure of compression stroke under different compression ratios was calculated,energy transfer and conversion process was analyzed,and the calculated results were experimentally verified. The results showed that the actual effective output of electronic energy and the compression energy stored in the com-pressed gas accounted for about 70%. The compression energy gradually increased with the increasing com-pression ratio. When the compression ratio was more than 7. 5,the actual compression energy increased slowly and the energy error between simulation and test decreased.展开更多
Two quinary high-entropy alloys （HEAs） with equiatomic concentrations formed by doping either Cu or A1 elements into the quaternary NiFeCoCr alloy are produced by arc melting and spray casting techniques. Their entr...Two quinary high-entropy alloys （HEAs） with equiatomic concentrations formed by doping either Cu or A1 elements into the quaternary NiFeCoCr alloy are produced by arc melting and spray casting techniques. Their entropy of fusion, thermal expansion coefficient and thermal diffusivity are experimentally investigated with differential scanning cMorimetry, dilatometry and laser flash methods. The NiFeCoCrCu HEAs contain a face- centered cubic high-entropy phase plus a minor interdendritic （Cu） phase and display a lower entropy of fasion and the Vickers hardness. The NiFeCoCrAl HEAs consist of two body-centered cubie high-entropy phases with coarse dendritic structures and show higher entropy of fusion and the Vickers hardness. Both the thermal expansion coefficient and the thermal diffusivity of the former Cu-doped alloy are signitieantly larger than those of the latter At-doped M1oy. Although the temperature dependence of thermal diffusivity is similar for both HEAs, it is peculiar that the thermal expansion curve of the NiFeCoCrAl alloy exhibits an inflexion at temperatures of 860-912 K.展开更多
The interaction between the high pressure gas and the control fluid and the movement mechanism of the control fluid in compound perforation were studied by a series of large-scale experiments, where the movement behav...The interaction between the high pressure gas and the control fluid and the movement mechanism of the control fluid in compound perforation were studied by a series of large-scale experiments, where the movement behavior of the control fluid was observed. The curves of measured pressure were analyzed, a mathematical model for the rigid movement of the control fluid was established, and the movement velocity of control fluid was analyzed. Moreover, the velocity from experimental results and velocity from an analytical solution were contrasted. The movement of the control fluid in the initial stage was similar to the rigid movement; however, the propagation of the pressure wave in the control fluid should be taken into account. Experimental results are significant for research on the movement mechanism of control fluid in compound perforation.展开更多
The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry...The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry rock.At present,how temporary plugging agents plug artificial fractures under high temperature remains unclear.In this paper,by establishing an improved experimental system for the evaluation of temporary plugging performance at high temperature,we clarified the effects of high temperature,injection rate,and fracture width on the pressure response and plugging efficiency of the fracture.The results revealed that the temporary plugging process of artificial fractures in hot dry rock can be divided into four main stages:the initial stage of temporary plugging,the bridging stage of the particles,the plugging formation stage,and the high-pressure dense plugging stage.As the temperature increases,the distribution distance of the temporary plugging agent,the number of pressure fluctuations,and the time required for crack plugging increases.Particularly,when the temperature increases by 100℃,the complete plugging time increases by 90.7%.展开更多
The launching and recovery process of a human-occupied vehicle(HOV)faces more complex wave effects than other types of submersible operations.However,due to the nonlinearity between the HOV and its mother ship,difficu...The launching and recovery process of a human-occupied vehicle(HOV)faces more complex wave effects than other types of submersible operations.However,due to the nonlinearity between the HOV and its mother ship,difficulties occur in theoretically simulating their coupled motion and hydrodynamics.The coupled motion responses and the load under different regular wave conditions are investigated experimentally in this study.The optimized design of the experimental scheme simulated the launching and recovery process of the mother ship and HOV in regular waves.The attitude sensor performed synchronous real-time measurement of the coupled motion between the mother ship and HOV as well as obtained the load data on the coupled motion under different cable lengths.The results show that models in heading waves mainly lead to the vertical motion of the hoisting point.In beam waves,the transverse and vertical motions of the hoisting point occur in a certain frequency of waves.Under the heading and beam wave conditions,the longer the hoisting cable is,the greater the movement amplitude of the submersible is.Moreover,compared with the condition of the beam waves,the hoisting submersible has less influence on the mother ship under the condition of the heading waves.The findings provide theoretical support for the design optimization of the launching and recovery operation.展开更多
Various sources of solid particles might exist in the coolant flow of a liquid metal cooled fast reactor(e.g.,through chemical interaction between the coolant and impurities,air,or water,through corrosion of structura...Various sources of solid particles might exist in the coolant flow of a liquid metal cooled fast reactor(e.g.,through chemical interaction between the coolant and impurities,air,or water,through corrosion of structural materials,or from damaged/molten fuel).Such particles may cause flow blockage accidents in a fuel assembly,resulting in a reduction in coolant flow,which potentially causes a local temperature rise in the fuel cladding,cladding failure,and fuel melt.To understand the blockage formation mechanism,in this study,a series of simulated experiments was conducted by releasing different solid particles from a release device into a reducer pipe using gravity.Through detailed analyses,the influence of various experimental parameters(e.g.,particle diameter,capacity,shape,and static friction coefficient,and the diameter and height of the particle release nozzle)on the blockage characteristics(i.e.,blockage probability and position)was examined.Under the current range of experimental conditions,the blockage was significantly influenced by the aforementioned parameters.The ratio between the particle diameter and outlet size of the reducer pipe might be one of the determining factors governing the occurrence of blockage.Specifically,increasing the ratio enhanced blockage(i.e.,larger probability and higher position within the reducer pipe).Increasing the particle size,particle capacity,particle static friction coefficient,and particle release nozzle diameter led to a rise in the blockage probability;however,increasing the particle release nozzle height had a downward influence on the blockage probability.Finally,blockage was more likely to occur in non-spherical particles case than that of spherical particles.This study provides a large experimental database to promote an understanding of the flow blockage mechanism and improve the validation process of fast reactor safety analysis codes.展开更多
Mainly for the problem that the friction force generated by the existing process of bind-ing,fixing and fastening the flexible cable on the satellite is unknown,the friction force analysis and experimental research on...Mainly for the problem that the friction force generated by the existing process of bind-ing,fixing and fastening the flexible cable on the satellite is unknown,the friction force analysis and experimental research on the binding point of the flexible cable are carried out.The equivalent model of the cable bundle bound by nylon cable ties is established,the force on the binding point is analyzed,and the empirical formula for calculating the friction force at the binding point is estab-lished.The formula shows that the friction force is related to the cable bundle diameter,the number of winding cycles of silicone rubber tape,the width of nylon cable ties,and the binding force.The friction force tests of the cable diameter of 5.06 mm,8.02 mm,24.02 mm,38.04 mm under different winding turns of tape were carried out,which was compared with the theoretical calculation value.It is concluded that the calculation accuracy of the theoretical model is more than 95%,which can estimate the actual friction force value accurately.This provides a reference and basis for the theoretical and experimental research on the friction force of the flexible cable binding point on satellite.展开更多
The poor fatigue properties and high rigidity of cement asphalt emulsion treated mis(CETM) have for a long time been problems restricting its further development making it impossible for C-ETMto be used as surface lay...The poor fatigue properties and high rigidity of cement asphalt emulsion treated mis(CETM) have for a long time been problems restricting its further development making it impossible for C-ETMto be used as surface layer materials. In this paper, a new kind of cement asphalt emulsion composite-rubberized asphalt emulsion modified Portland cement concrete (RACC) was proposed, which was formed by dispersing rubberized aSPhalt emulsion coated coarse aggregates into cement mortar matrix. In order to evaluate systematically the performance of RACC, laboratory tests with nearly one thousand SPecimen were conducted for resilient modulus, fatigue properties, ultimate ban and length,abrasion, temperature contraction, and dry shrinkage. The experimental results show that the problems existed in C-ETM have to a great extends been solved by RACc. To verify the field performance and inquire into paving technology, teSt road appearsatlsfactory it is concluded that when thed ape surface laycr of semi-rigid base course, RACC is more for surface layer material than both Portland cement concrete(PCC) and asphalt concrete(AC)展开更多
Output performance of a continuous-wave TIn：YAP laser pumped passively Q-switched Ho：YLF laser is demon- strated with a polycrystalline Cr2＋ ：ZnS as the saturable absorber. We compare the experimental results at t...Output performance of a continuous-wave TIn：YAP laser pumped passively Q-switched Ho：YLF laser is demon- strated with a polycrystalline Cr2＋ ：ZnS as the saturable absorber. We compare the experimental results at the three different distances L of the polycrystalline Cr2＋ ：ZnS saturable absorber to the output coupler. The pulse width almost remains constant for different L, when the incident pump power is changed in the range of 7.9 27.1 W. The shortest pulse duration of 33.3 ns for L = 105 mm and the highest average output power of 6.8 W for L = 5 mm are obtMned at the incident pump power of 27.1 W. The output wavelength of the passively Q-switched laser shifts to 2045.2nm from 2064.7nm in the cw operation. The beam quality factor of M2 is 1.2.展开更多
By using a longitudinal static magnetic field, we have shown that it is possible to excite an intensive plasma in a simple stainless steel tube which is connected with a RF power supply. Under certain conditions, the ...By using a longitudinal static magnetic field, we have shown that it is possible to excite an intensive plasma in a simple stainless steel tube which is connected with a RF power supply. Under certain conditions, the very bright Ar II lines were excited. The emission intensities of Ar II lines were increased with the increase in RF power, magnetic field, and the decrease in argon pressure. As the plasma-sheath boundary oscillating under the RF voltage, the plasma column is periodically compressed by the oscillating boundary.展开更多
Double resonance optical pumping spectroscopy has an outstanding advantage of high signal-to-noise ratio, thus having potential applications in precision measurement. With the counter propagated 780nm and 776nm laser ...Double resonance optical pumping spectroscopy has an outstanding advantage of high signal-to-noise ratio, thus having potential applications in precision measurement. With the counter propagated 780nm and 776nm laser beams acting on a rubidium vapor cell, the high resolution spectrum of 5S1/2 - 5P3/2 - 5D5/2 ladder-type transition of ST Rb atoms is obtained by monitoring the population of the 5S1/2 ground state. The dependence of the spectroscopy lineshape on the probe and coupling fields are comprehensively studied in theory and experiment. This research is helpful for measurement of fundamental physical constants by high resolution spectroscopy.展开更多
This paper presents the surface temperature behavior of M42 high-speed tool steel samples during N+ implantation in an industrialized GLZ-100 metal-ion implantation machine. A detail study has been made on the paramet...This paper presents the surface temperature behavior of M42 high-speed tool steel samples during N+ implantation in an industrialized GLZ-100 metal-ion implantation machine. A detail study has been made on the parameters of N+ implantation. Optimized technical parameters have been presented. The microhardness of the sample surface implanted under these parameters has been increased by a factor of 2.3, and the wear-resistance has been improved by about 5.4 times. The research on the mechanism of surface modification of M42 steel by nitrogen ion implantation has also been made.展开更多
文摘Aim To design and experimentally study an 80C196KC-based SRD (switched re- luctance motor drive drive sytem) controller,Methods with the guidelines of the digitized SRD system controller,the circuit design and software programming were completed,and a relevantexperimental system was PUT forward to test the newly designed controller.Result The experi-mental study showed that the newlydesigned controller had good speed-adjusting characteristicfor a switched reluctance motor ,its stable error was less than 5% and its full-load startingtime was shorter than 1.8s .Conclusion The new controller has reasonable circuit design and suitable controlling algorithm,and it is a feasible SRD system controller design scheme.
基金supported by the National Natural Science Foundation of China (No.50475037)
文摘Theoretical analysis and field monitoring show that lateral vibration has very important effect on casing wear in deep & ultra-deep well drilling. The wear mechanism of casing under impact-sliding work conditions has been investigated and many experiments have been completed with a newly developed full-scale casing wear test machine. Test results present that adhesion wear, contact fatigue, and grinding abrasion are the main wear mechanisms under impact-sliding test conditions. The friction coefficient and linear wear rate of the casing rise obviously with an increase in impact load. And the larger the impact load, the rougher the worn surface of the casing. The linear wear rate decreased slightly but the average friction coefficient increased slightly with an increase in impact frequency under an impact load of 2,500 N. Both the linear wear rate of the casing and the average friction coefficient increased substantially with an increase in impact frequency under an impact load of 4,000 N. Under lower impact load conditions, grinding abrasion and contact fatigue are the main mechanisms of casing wear; under higher impact load conditions, adhesion wear and contact fatigue are the main mechanisms of casing wear.
文摘This paper presented the results of an experimental investigation into the resistance performance of a wave-piercing trimaran with three alternative side hull forms,including asymmetric inboard,asymmetric outboard,and symmetric at various stagger/separation positions.Model tests were carried out at the National Iranian Marine Laboratory(NIMALA)towing tank using a scale model of a trimaran at the Froude numbers from 0.225 to 0.60.Results showed that by moving the side hulls to the forward of the main hull transom,the total resistance coefficient of trimaran decreased.Findings,furthermore,demonstrated that the symmetry shape of the side hull had the best performance on total resistance among three side hull forms.Results of this study are useful for selecting the side hull configuration from the resistance viewpoint.
基金supported by National Science and Technology Major Project(No.J2019-II-0014-0035)。
文摘Effective control of hypersonic transition is essential.In order to avoid affecting the structural proflle of the aircraft,as well as reducing power consumption and electromagnetic interference,a low-frequency surface arc plasma disturbance experiment to promote hypersonic transition was carried out in theΦ0.25 m double-throat Ludwieg tube wind tunnel at Huazhong University of Science and Technology.Contacting printed circuit board sensors and non-contact focused laser differential interferometry testing technology were used in combination.Experimental results showed that the low-frequency surface arc plasma actuation had obvious stimulation effects on the second-mode unstable wave and could promote boundary layer transition by changing the spectral characteristics of the second-mode unstable wave.At the same time,the plasma actuation could promote energy exchange between the second-mode unstable wave and other unstable waves.Finally,the corresponding control mechanism is discussed.
基金This work was supported by the National Science Foundation of China No.19835030.
文摘Usually, the electrical breakdown of dielectric barrier discharge (DBD) at atmo-spheric pressure leads to a filamentary non-homogeneous discharge. However, it is also possible to obtain a diffuse DBD in homogeneous form, called atmospheric pressure glow discharge (APGD). We obtained a uniform APGD in helium and in the mixture of argon with alcohol, and studied the electrical characteristics of helium APGD. It is found that the relationship between discharge current and source frequency is different depending on the difference in gas gap when the applied voltage is kept constant. The discharge current shows an increasing trend with the increased frequency when gas gap is 0.8 cm, but the discharge current tends to decrease with the increased frequency when the gas gap increases. The discharge current always increases with the increased applied voltage when the source frequency is kept constant. We also observed a glow-like discharge in nitrogen at atmospheric pressure.
基金Supported by the National Basic Research Program of China under Grant No 2013CB834404the National Natural Science Foundation of China under Grant Nos 11375268,11475263,U1432246 and U1432127
文摘The investigation of beta-delayed proton decay mode has become a powerful probe to study the proton-rich nuclei and their nuc/eax structure. To study exotic nuclei with extremely low purity produced by the Radioactive Ion Beam Line in Lanzhou, we perform an experiment of beta-delayed proton emission of 36,37^Ca under a high-intensity continuous-beam mode. Ions are implanted into a double-sided silicon strip detector, where the subsequent decays are correlated to the preceding implantations in time sequence. The energy spectra of delayed protons from 36,37^Caβ decay, half-lives and decay branching ratios axe measured. The experimental results confirm the previous literature data and some improved results are obtained as well, demonstrating the feasibility of our detection approach and the reliability of our data analysis procedure. This allows for the development of more powerful detection arrays and further research on nuclei closer to proton-drip line on the basis of present work.
基金This work was supported by the National Natural Science Foundation of China, Grant No. 10035020
文摘A coaxial multi-gap multi-channel spark switch with stainless-steel-spring ring gap electrodes is designed and investigated. The switch is triggered by a pulse applied to the cylindrical electrode outside the discharging channel through a parasitic capacitance coupling. The jitter of the switch is reduced by several short-distance gas gaps in series, and its inductance is reduced by a multi-channel discharge on account of the inductance isolation between the coils of the spring ring electrode. The experimental results indicate that the switch is of low inductance (15-30 nH), low jitter (-3 ns), and stable breakdown performance
文摘A 10 J, 4o us XeCl laser interaction with LY12 aluminum and optical glass K9 targets is reported. The properties of laser-produced plasma (LPP) are analyzed. As a result, some parameters such as plasma ignition threshold and plasma plume expansion velocity are obtained. Also, Laser induced pulse on irradiated targets are given.
基金Supported by the National Natural Science Foundation of China(51006010)the Program of Introducing Talents of Discipline to Universities(B12022)
文摘The compression stroke characteristics of free-piston engine generator were studied. The numerical model of the compression stroke was established based on thermodynamics and dynamics equation,and the leak loss,heat loss and friction loss were considered. Through solving numerical equations,the in-cylinder pressure of compression stroke under different compression ratios was calculated,energy transfer and conversion process was analyzed,and the calculated results were experimentally verified. The results showed that the actual effective output of electronic energy and the compression energy stored in the com-pressed gas accounted for about 70%. The compression energy gradually increased with the increasing com-pression ratio. When the compression ratio was more than 7. 5,the actual compression energy increased slowly and the energy error between simulation and test decreased.
基金Supported by the National Natural Science Foundation of China under Grant Nos 51571163,51371150,51271150 and 51327901
文摘Two quinary high-entropy alloys （HEAs） with equiatomic concentrations formed by doping either Cu or A1 elements into the quaternary NiFeCoCr alloy are produced by arc melting and spray casting techniques. Their entropy of fusion, thermal expansion coefficient and thermal diffusivity are experimentally investigated with differential scanning cMorimetry, dilatometry and laser flash methods. The NiFeCoCrCu HEAs contain a face- centered cubic high-entropy phase plus a minor interdendritic （Cu） phase and display a lower entropy of fasion and the Vickers hardness. The NiFeCoCrAl HEAs consist of two body-centered cubie high-entropy phases with coarse dendritic structures and show higher entropy of fusion and the Vickers hardness. Both the thermal expansion coefficient and the thermal diffusivity of the former Cu-doped alloy are signitieantly larger than those of the latter At-doped M1oy. Although the temperature dependence of thermal diffusivity is similar for both HEAs, it is peculiar that the thermal expansion curve of the NiFeCoCrAl alloy exhibits an inflexion at temperatures of 860-912 K.
文摘The interaction between the high pressure gas and the control fluid and the movement mechanism of the control fluid in compound perforation were studied by a series of large-scale experiments, where the movement behavior of the control fluid was observed. The curves of measured pressure were analyzed, a mathematical model for the rigid movement of the control fluid was established, and the movement velocity of control fluid was analyzed. Moreover, the velocity from experimental results and velocity from an analytical solution were contrasted. The movement of the control fluid in the initial stage was similar to the rigid movement; however, the propagation of the pressure wave in the control fluid should be taken into account. Experimental results are significant for research on the movement mechanism of control fluid in compound perforation.
基金supported financially by the Beijing Natural Science Foundation Project(No.3222030)the National Natural Science Foundation of China(No.51936001,No.52274002 and No.52192622)+1 种基金the PetroChina Science and Technology Innovation Foundation Project(2021DQ02–0201)Award Cultivation Foundation from Beijing Institute of Petrochemical Technology(No.BIPTACF-002).
文摘The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry rock.At present,how temporary plugging agents plug artificial fractures under high temperature remains unclear.In this paper,by establishing an improved experimental system for the evaluation of temporary plugging performance at high temperature,we clarified the effects of high temperature,injection rate,and fracture width on the pressure response and plugging efficiency of the fracture.The results revealed that the temporary plugging process of artificial fractures in hot dry rock can be divided into four main stages:the initial stage of temporary plugging,the bridging stage of the particles,the plugging formation stage,and the high-pressure dense plugging stage.As the temperature increases,the distribution distance of the temporary plugging agent,the number of pressure fluctuations,and the time required for crack plugging increases.Particularly,when the temperature increases by 100℃,the complete plugging time increases by 90.7%.
基金National Natural Science Foundation of China(Grant No.51909039)Shandong Provincial Key Laboratory of Ocean Engineering(Grant No.201807).
文摘The launching and recovery process of a human-occupied vehicle(HOV)faces more complex wave effects than other types of submersible operations.However,due to the nonlinearity between the HOV and its mother ship,difficulties occur in theoretically simulating their coupled motion and hydrodynamics.The coupled motion responses and the load under different regular wave conditions are investigated experimentally in this study.The optimized design of the experimental scheme simulated the launching and recovery process of the mother ship and HOV in regular waves.The attitude sensor performed synchronous real-time measurement of the coupled motion between the mother ship and HOV as well as obtained the load data on the coupled motion under different cable lengths.The results show that models in heading waves mainly lead to the vertical motion of the hoisting point.In beam waves,the transverse and vertical motions of the hoisting point occur in a certain frequency of waves.Under the heading and beam wave conditions,the longer the hoisting cable is,the greater the movement amplitude of the submersible is.Moreover,compared with the condition of the beam waves,the hoisting submersible has less influence on the mother ship under the condition of the heading waves.The findings provide theoretical support for the design optimization of the launching and recovery operation.
基金supported by the Basic and Applied Basic Research Foundation of Guangdong Province(Nos.2021A1515010343,2022A1515011582)the Science and Technology Program of Guangdong Province(Nos.2021A0505030026,2022A0505050029).
文摘Various sources of solid particles might exist in the coolant flow of a liquid metal cooled fast reactor(e.g.,through chemical interaction between the coolant and impurities,air,or water,through corrosion of structural materials,or from damaged/molten fuel).Such particles may cause flow blockage accidents in a fuel assembly,resulting in a reduction in coolant flow,which potentially causes a local temperature rise in the fuel cladding,cladding failure,and fuel melt.To understand the blockage formation mechanism,in this study,a series of simulated experiments was conducted by releasing different solid particles from a release device into a reducer pipe using gravity.Through detailed analyses,the influence of various experimental parameters(e.g.,particle diameter,capacity,shape,and static friction coefficient,and the diameter and height of the particle release nozzle)on the blockage characteristics(i.e.,blockage probability and position)was examined.Under the current range of experimental conditions,the blockage was significantly influenced by the aforementioned parameters.The ratio between the particle diameter and outlet size of the reducer pipe might be one of the determining factors governing the occurrence of blockage.Specifically,increasing the ratio enhanced blockage(i.e.,larger probability and higher position within the reducer pipe).Increasing the particle size,particle capacity,particle static friction coefficient,and particle release nozzle diameter led to a rise in the blockage probability;however,increasing the particle release nozzle height had a downward influence on the blockage probability.Finally,blockage was more likely to occur in non-spherical particles case than that of spherical particles.This study provides a large experimental database to promote an understanding of the flow blockage mechanism and improve the validation process of fast reactor safety analysis codes.
基金supported by National Defense Basic Scientific Research Funding Project(No.JCKY2022203C048)Equipment Advanced Research Funding Program(No.41423010401).
文摘Mainly for the problem that the friction force generated by the existing process of bind-ing,fixing and fastening the flexible cable on the satellite is unknown,the friction force analysis and experimental research on the binding point of the flexible cable are carried out.The equivalent model of the cable bundle bound by nylon cable ties is established,the force on the binding point is analyzed,and the empirical formula for calculating the friction force at the binding point is estab-lished.The formula shows that the friction force is related to the cable bundle diameter,the number of winding cycles of silicone rubber tape,the width of nylon cable ties,and the binding force.The friction force tests of the cable diameter of 5.06 mm,8.02 mm,24.02 mm,38.04 mm under different winding turns of tape were carried out,which was compared with the theoretical calculation value.It is concluded that the calculation accuracy of the theoretical model is more than 95%,which can estimate the actual friction force value accurately.This provides a reference and basis for the theoretical and experimental research on the friction force of the flexible cable binding point on satellite.
文摘The poor fatigue properties and high rigidity of cement asphalt emulsion treated mis(CETM) have for a long time been problems restricting its further development making it impossible for C-ETMto be used as surface layer materials. In this paper, a new kind of cement asphalt emulsion composite-rubberized asphalt emulsion modified Portland cement concrete (RACC) was proposed, which was formed by dispersing rubberized aSPhalt emulsion coated coarse aggregates into cement mortar matrix. In order to evaluate systematically the performance of RACC, laboratory tests with nearly one thousand SPecimen were conducted for resilient modulus, fatigue properties, ultimate ban and length,abrasion, temperature contraction, and dry shrinkage. The experimental results show that the problems existed in C-ETM have to a great extends been solved by RACc. To verify the field performance and inquire into paving technology, teSt road appearsatlsfactory it is concluded that when thed ape surface laycr of semi-rigid base course, RACC is more for surface layer material than both Portland cement concrete(PCC) and asphalt concrete(AC)
基金Supported by the National Natural Science Foundation of China under Grant Nos 61308009,61405047,and 50990301the Postdoctoral Science Foundation of China under Grant No 2013M540288+1 种基金the Fundamental Research Funds for the Central Universities under Grant Nos HIT.NSRIF.2014044 and HIT.NSRIF.2015042the Science Fund for Outstanding Youths of Heilongjiang Province under Grant No JQ201310
文摘Output performance of a continuous-wave TIn：YAP laser pumped passively Q-switched Ho：YLF laser is demon- strated with a polycrystalline Cr2＋ ：ZnS as the saturable absorber. We compare the experimental results at the three different distances L of the polycrystalline Cr2＋ ：ZnS saturable absorber to the output coupler. The pulse width almost remains constant for different L, when the incident pump power is changed in the range of 7.9 27.1 W. The shortest pulse duration of 33.3 ns for L = 105 mm and the highest average output power of 6.8 W for L = 5 mm are obtMned at the incident pump power of 27.1 W. The output wavelength of the passively Q-switched laser shifts to 2045.2nm from 2064.7nm in the cw operation. The beam quality factor of M2 is 1.2.
文摘By using a longitudinal static magnetic field, we have shown that it is possible to excite an intensive plasma in a simple stainless steel tube which is connected with a RF power supply. Under certain conditions, the very bright Ar II lines were excited. The emission intensities of Ar II lines were increased with the increase in RF power, magnetic field, and the decrease in argon pressure. As the plasma-sheath boundary oscillating under the RF voltage, the plasma column is periodically compressed by the oscillating boundary.
基金Supported by the National Key R&D Program of China under Grant No 2017YFA0304203the National Natural Science Foundation of China under Grant Nos 61575116,61705122,61728502,91736209 and 11434007+2 种基金the Changjiang Scholars and Innovative Research Team in University of Ministry of Education of China under Grant No IRT13076the Program for Sanjin Scholars of Shanxi Province,the Applied Basic Research Project of Shanxi Province under Grant No 201701D221004the Fund for Shanxi ‘1331 Project’ Key Subjects Construction
文摘Double resonance optical pumping spectroscopy has an outstanding advantage of high signal-to-noise ratio, thus having potential applications in precision measurement. With the counter propagated 780nm and 776nm laser beams acting on a rubidium vapor cell, the high resolution spectrum of 5S1/2 - 5P3/2 - 5D5/2 ladder-type transition of ST Rb atoms is obtained by monitoring the population of the 5S1/2 ground state. The dependence of the spectroscopy lineshape on the probe and coupling fields are comprehensively studied in theory and experiment. This research is helpful for measurement of fundamental physical constants by high resolution spectroscopy.
文摘This paper presents the surface temperature behavior of M42 high-speed tool steel samples during N+ implantation in an industrialized GLZ-100 metal-ion implantation machine. A detail study has been made on the parameters of N+ implantation. Optimized technical parameters have been presented. The microhardness of the sample surface implanted under these parameters has been increased by a factor of 2.3, and the wear-resistance has been improved by about 5.4 times. The research on the mechanism of surface modification of M42 steel by nitrogen ion implantation has also been made.
