[Background and purposes]In recent years,there has been growing attention in academia and industry on the development of high-performance electromagnetic wave(EMW)absorbing materials.However,creating lightweight broad...[Background and purposes]In recent years,there has been growing attention in academia and industry on the development of high-performance electromagnetic wave(EMW)absorbing materials.However,creating lightweight broadband absorbers remains a challenge in terms of practical applications.EMW absorbing materials primarily rely on the magnetic loss of magnetic materials and/or the dielectric loss of dielectric materials to convert EMW energy into thermal energy for dissipation.Among various magnetic materials,Fe_(3)O_(4) plays an irreplaceable role in EMW absorption due to its high saturation magnetization,low cost and compatible dielectric loss in the gigahertz frequency range.Nevertheless,the high density,large matching thickness and narrow absorption bandwidth of Fe_(3)O_(4) pose significant challenges for practical applications.In contrast,one-dimensional(1D)structures not only retain the characteristic properties of lightweight,chemical stability and high dielectric loss,but also exhibit anisotropic structures and large aspect ratios.Additionally,researchers have found that the minimum reflection loss(RL)of hollow carbon materials with mesopores is nearly four times that of non-porous hollow carbon materials and nine times that of dense carbon materials.According to Maxwell's EMW theory,composites consisting of Fe_(3)O_(4) and one-dimensional(1D)mesoporous carbon materials can leverage their respective advantages by optimizing the composition and structure of the composites to balance u,and Er,thereby enhancing EMW absorption performance.Additionally,numerous studies have demonstrated that composites composed of multi-component heterostructures significantly enhance the EAB.This enhancement is primarily ascribed to the numerous interface polarization losses generated by the additional heterostructure interfaces,which also improve the overall impedance matching of the composites.In this study,we leverage the advantages of magnetic/carbon composites,one-dimensional(1D)mesoporous carbon and multi-component heterostructures to prepare a composite of 1D mesoporous carbon-coated manganese oxide(Mn_(3)O_(4) and MnO,denoted as Mn_(x)O_(y))embedded with Fe_(3)0_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4)).This composite was synthesized and its formation mechanism and microstructure were analyzed in detail.At the same time,the influence of this Mn_(x)O_(y)/C@Fe_(3)O_(4) structure on EMW properties and absorbing performance was further discussed.[Methods]Firstly,MnO_(2) nanowires were synthesized by using a simple hydrothermal method.Then,the MnO_(2) nanowires served as templates for the synthesis of MnO_(2)/PDA@Fe^(3+)composites through the in-situ polymerization of dopamine and Fe^(3+)adsorption.Finally,1D mesoporous carbon-coated manganese oxide composite embedded with Fe_(3)O_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4))composites were obtained after heat treatment at 550℃ in N_(2).The crystal structure of the samples was analyzed using X-ray diffractometer with Cu Ka irradiation.Scanning electron microscopy(SEM)and high-resolution transmission electron microscopy(TEM)were used to observe microstructure and morphology of the samples.Nitrogen sorption measurements were obtained at 77 K on a Quantachrome surface area and pore size analyzer to measure the specific surface area and pore size distribution.XPS analysis was performed on X-ray photoelectron spectrometer with monochromatic Al Ka radiation.Magnetization curves of the samples were recorded with a Quantum Design physical property measurement system(PPMS-9)at room temperature.The electromagnetic parameters of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites were measured using an Agilent N5230C network analyzer in the frequency range of 2-18 GHz.For electromagentic testing,the Mn,Oy/C@Fe34 composites and paraffin wax were mixed at 50°C according to the mass ratio of 15 wt.%,20 wt.%and 25 wt.%,and pressed in a special mold to make coaxial rings(inner diameter=3.04 mm,outer diameter-7 mm),which were denoted as S-1,S-2 and S-3,respectively.[Results]SEM images illustrate the preparation process of iD mesoporous carbon-coated manganese oxide embedded with Fe3O4 nanoparticles composites(Mn_(x)O_(y)/C@Fe_(3)O_(4)).Most of the manganese oxide(Mn,Oy)was reduced to granular after heat treatment,while the outer carbon layer remains its 1D morphology and the carbon layer is interspersed with Fe_(3)O_(4) nanoparticles.The diffraction peaks of MnO_(2) nanowires align well with the body-centered tetragonal a-MnO2.For the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites,the signals of α-MnO_(2) disappears,followed by the emergence of Mn_(3)O_(4) and three prominent diffraction peaks for the cubic MnO.In addition,four weak diffraction peaks correspond to the magnetite Fe_(3)O_(4),consistent with the HRTEM results.The corresponding nitrogen adsorption-desorption isotherm and pore size distribution curve are presented to further analyze the mesoporous structure of composite.The surface composition and element valence states of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite were investigated by using XPS.The polarization relaxation processes were analyzed according to the Debye theory which describes the relationship between e'and e".Besides the polarization loss,the contribution of the conduction loss plays an important role for the overall dielectric loss.The magnetization curve of Mn_(x)O_(y)/C@Fe_(3)O_(4) exhibits typical ferromagnetic behavior.The permittivity parameter(Co),defined as Co=u"(u)^(-2)f^(-1) determine the contribution of eddy current effect to magnetic loss.The tand values are all larger than those of tand,for the three samples,indicating that the loss capacity of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites is mainly derived from the dielectric loss.Although tand,is smaller,it plays an important role in improving the impedance matching of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites.When the filler loading is 15 wt.%,the RL of sample S-1 is about-10.0 dB at the thickness of 1.5 mm with narrow EAB.As the filler loading increased to 20 wt.%,the RL of sample S-2 reached-62.0 dB at a thickness of 2.2 mm and the EAB was 6.4 GHz at a small thickness of 1.7 mm.When the filler loading is further increased to 25 wt.%,the microwave absorption performance of sample S3 decreased significantly with a little region of RL<-10.0 dB at the thickness of 5.0 mm.The values of[Zin/Zol of the three samples at thicknesses of 1.5-5.0 mm were calculated.Due to good impedance matching of S-2,the incident EMW can enter the material and then can be dissipated through dipole polarization loss,interface polarization loss,conduction loss,eddy current loss and natural ferromagnetic resonance loss.[Conclusions]1D Mn_(x)O_(y)/C@Fe_(3)O_(4) was synthesized via a process involving the coating of polydopamine,adsorption of Fe(ll)salts and heat treatment,using MnO_(2) nanowires as templates.The multi-component heterostructure of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite(Mn_(3)O_(4),MnO,Fe_(3)O_(4),and C)enhances the interfacial interactions between the different phases,providing increased interface polarization loss under the action of an alternating electromagnetic field.The numerous defects and terminal groups in the mesoporous carbon provide abundant dipole polarization centers.Additionally,the presence of mesopores reduces the weight of the material while increasing the multiple scattering losses of the electromagnetic waves within the material.The ID carbon structure in the matrix forms a conductive network between adjacent fibers,facilitating electron migration and transition,thereby enhancing conductive loss.The incorporation of magnetic Fe_(3)O_(4) nanoparticles introduces eddy current loss and natural ferromagnetic resonance loss,thus increasing magnetic loss.Moreover,the synergistic effect between dielectric and magnetic losses improves the impedance matching of the material,leading to excellent EMW absorption performance.展开更多
Constructing a photoconductive semiconductor switch (PCSS)-metal coil structure, we discovered anew phenomenon of electromagnetic oscillation in vanadium-compensation semi-insulating (VCSI) PCSS. Here thePCSS responds...Constructing a photoconductive semiconductor switch (PCSS)-metal coil structure, we discovered anew phenomenon of electromagnetic oscillation in vanadium-compensation semi-insulating (VCSI) PCSS. Here thePCSS responds to laser pulse and high-voltage signal while the metal coil generates an oscillating voltage pulseenvelope signal. The generation of this oscillating signal is not related to the input bias voltage of the PCSS, the pulsecircuit components, or the electrode structure of the PCSS, rather it is related to the output characteristic of the PCSS.This physical phenomenon can be explained using the current surge model in photoconducting antenna. Preparingohmic contact electrode on the silicon carbide material forms the PCSS, which generates a large number ofphotogenerated carriers when ultra-fast laser pulses irradiate the surface of the material and Simultaneously applies abias voltage signal between the electrode. At this time inside the PCSS the electric field causes the transient current,radiating electromagnetic wave to the metal coil to generate oscillating signal.展开更多
In this study,the potential application of shaped charge jets as transient antennas for electromagnetic signal transmission was explored and an electromagnetic pulse radiation system with a shaped charge jet as a tran...In this study,the potential application of shaped charge jets as transient antennas for electromagnetic signal transmission was explored and an electromagnetic pulse radiation system with a shaped charge jet as a transient antenna was proposed.During the research,crucial characteristics of the transient antenna formed by a shaped charge with a 30 mm diameter,such as resonant frequency,radiation pattern,and radiation efficiency,were evaluated.The typical shaped charge jet morphology was obtained based on the simulations,in which it could insight the dynamic behavior of the shaped charge jet selected.An equivalent model experiment was employed to test the radiation efficiency,and it showed that a shorting pin loading method could increase the relative bandwidth of the jet antenna to 32.8%,and the experimental results correlate with the theoretical predictions for half-wave dipole antennas reasonably well.Additionally,variations in the diameter of the shaped charge jet were found to affect the input impedance and impedance bandwidth,while the length of the jet influenced the resonant frequency of the antenna.This suggests that altering these parameters can achieve reconfigurability of the jet antenna.展开更多
Space electromagnetic docking technology, free of propellant and plume contamination, offers continuous, reversible and synchronous controllability, which is widely applied in the future routine on-orbit servicing mis...Space electromagnetic docking technology, free of propellant and plume contamination, offers continuous, reversible and synchronous controllability, which is widely applied in the future routine on-orbit servicing missions. Due to the inherent nonlinearities, couplings and uncertainties of an electromagnetic force model, the dynamics and control problems of them are difficult. A new modeling approach for relative motion dynamics with intersatellite force is proposed. To resolve these control problems better, a novel nonlinear control method for soft space electro-magnetic docking is proposed, which combines merits of artificial potential function method, Lyapunov theory and extended state observer. In addition, the angular momentum management problem of space electromagnetic docking and approaches of handling it by exploiting the Earth＇s magnetic torque are investigated. Finally, nonlinear simulation results demonstrate the feasibility of the dynamic model and the novel nonlinear control method.展开更多
This paper presents the principle of electromagnetic missile from the mathematical point of view, and verifies rigorously that the radiating power over whole space is limited.
In the earth there exist various forms of natural and artificial electromagnetic fields;the study of their formation, laws of development and practical application constitute the fundamental tasks of the discipline of...In the earth there exist various forms of natural and artificial electromagnetic fields;the study of their formation, laws of development and practical application constitute the fundamental tasks of the discipline of geoelectromagnetics.The currently app展开更多
As semiconductor technologies have been shrinking,the speed of circuits,integration density,and the number of I/O interfaces have been significantly increasing.As a consequence,electromagnetic emanation(EME)becomes a ...As semiconductor technologies have been shrinking,the speed of circuits,integration density,and the number of I/O interfaces have been significantly increasing.As a consequence,electromagnetic emanation(EME)becomes a critical issue in digital system designs.Electronic devices must meet electromagnetic compatibility(EMC)requirements to ensure that they operate properly,and safely without interference.I/O buffers consume high currents when they operate.The bonding wires,and lead frames are long enough to play as efficient antennas to radiate electromagnetic interference(EMI).Therefore,I/O switching activities significantly contribute to the EMI.In this paper,we evaluate and analyze the impact of I/O switching activities on the EME.We will change the circuit configurations such as the supply voltage for I/O banks,their switching frequency,driving current,and slew rate.Additionally,a trade-off between the switching frequencies and the number of simultaneous switching outputs(SSOs)is also considered in terms of EME.Moreover,we evaluate the electromagnetic emissions that are associated with the different I/O switching patterns.The results show that the electromagnetic emissions associated I/O switching activities depend strongly on their operating parameters and configurations.All the circuit implementations and measurements are carried out on a Xilinx Spartan-3 FPGA.展开更多
The rails of electromagnetic railgun can be ablated by the temperature rise due to current concentration.The current distributions on the rails and armature are not only affected by the skin effect,but also influenced...The rails of electromagnetic railgun can be ablated by the temperature rise due to current concentration.The current distributions on the rails and armature are not only affected by the skin effect,but also influenced by the proximity effect which is rarely mentioned.This paper illustrated the difference between skin effect and proximity effect,and the influencing factors of proximity effect were investigated.Results show that the current is concentrated on the surface around rails due to the skin effect,and the proximity effect exacerbates the current density on the inner surfaces of rails.Decrease in distance from rails enhances the proximity effect,but has nothing to do with the skin effect,which also augments the rail resistance,resulting in temperature rise.It can explain the reason why the ablation is often detected in the small caliber railgun.Research results in this paper can provide support for design and optimization of electromagnetic railgun.展开更多
The design of solid armature of railgun should take full account of its operating conditions and material properties because the armature is subjected to dynamic loading conditions and experiences a complicated electr...The design of solid armature of railgun should take full account of its operating conditions and material properties because the armature is subjected to dynamic loading conditions and experiences a complicated electrical,thermal and mechanical process in the interior ballistic cycle.In this paper present,we first introduced a multi-physical field model of railgun,followed by several examples to investigate the launching process.Especially,we used the explicit finite element method,in which material nonlinearity and geometric nonlinearity were accounted,to investigate the deform behaviors of solid armature.The results show that the dynamic mechanical process of armature is dependent on the armature geometry,material and exciting electric current.By the numerical simulation,the understanding of the fracture mechanism of solid armature was deepened.展开更多
Electromagnetic railgun attracts more and more attention due to its advantage in speed,cost,and obscurity.It is found that the rail should withstand huge mechanical and thermal shocks during the launching operation.Th...Electromagnetic railgun attracts more and more attention due to its advantage in speed,cost,and obscurity.It is found that the rail should withstand huge mechanical and thermal shocks during the launching operation.The forms of rail failure are accompanied by gouge,grooving,transition,and arc ablation,etc.The service life of the rail has become a bottleneck restricting the development of electromagnetic railgun technology.A series of researches are carried out to solve rail failure,including analysing the failure mechanism and using various advanced rail materials.This paper provides a comprehensive review of rail materials,including material composition,preparation,microstructure,and properties.We begin from a short background of the requirement of the rail material.Then a detailed investigation of rail materials is described,and the performances of those materials are introduced.Finally,further development prospect of rail material is discussed.展开更多
Facing the problems lack of considering the non-uniform distribution of the static bias magnetic field and computing the panicle displacements in the simulation model of electromagnetic acoustic transducer （EMAT）, a...Facing the problems lack of considering the non-uniform distribution of the static bias magnetic field and computing the panicle displacements in the simulation model of electromagnetic acoustic transducer （EMAT）, a multi-field coupled model was established and the finite element method （FEM） was presented to calculate the entire transduction process. The multi-field coupled model included the static magnetic field, pulsed eddy current field and mechanical field. The FEM equations of the three fields were derived by Garlerkin FEM method. Thus, the entire transduction process of the EMAT was calculated through sequentially coupling the three fields. The transduction process of a Lamb wave EMAT was calculated according to the present model and method. The results show that, by the present method, it is valid to calculate the particle displacement under the given excitation signal and non-uniformly distributed static magnetic field. Calculation error will be brought about if the non-uniform distribution of the static bias magnetic field is neglected.展开更多
Switched reluctance motors(SRM)with full-pitch windings and segmental rotors are particularly suitable for the drive systems in aerospace environments because of low wind(oil)resistance and iron losses at high speed.I...Switched reluctance motors(SRM)with full-pitch windings and segmental rotors are particularly suitable for the drive systems in aerospace environments because of low wind(oil)resistance and iron losses at high speed.In this paper,the authors have been studying electromagnetic design of this motor.展开更多
Effect of electromagnetic stirring on microstructure of AZ91-0.8%Ce magnesium alloy was investigated. The results show that electromagnetic stirring causes a change of morphology of α-Mg phase from coarse dendrites t...Effect of electromagnetic stirring on microstructure of AZ91-0.8%Ce magnesium alloy was investigated. The results show that electromagnetic stirring causes a change of morphology of α-Mg phase from coarse dendrites to fine rosette-like or spherical shape. Grain size is significantly refined within the range of input voltage 75?125 V, moreover, the optimum input voltage corresponded to the minimum value (64 μm) of grain size is 125 V. Compared to the non-stirred condition, the amount of β-Mg17Al12 precipitate under the stirred condition obviously increases. The grain refinement of AZ91-0.8%Ce alloy is mainly attributed to multiplication of existing grains in the melt caused by forced fluid flow under electromagnetic stirring condition. Addition of 0.8% Ce results in the formation of ‘necking’ at secondary dendrite arm roots of α-Mg crystals, and consequently, it is helpful to increase the number of heterogeneous nucleation.展开更多
In order to study the distribution of shale gas reservoir in the Babaoshan Basin of Eastern Kunlun,the wide-field electromagnetic(WFEM)survey was carried out to obtain the spatial distribution characteristics of the u...In order to study the distribution of shale gas reservoir in the Babaoshan Basin of Eastern Kunlun,the wide-field electromagnetic(WFEM)survey was carried out to obtain the spatial distribution characteristics of the underground electrical volume resistivity based on the delineation of the scope of the Babaoshan Basin by regional gravity data.The basic characteristics of the basement,basin framework,and extension,vertical change,burial depth of dark mud shale in this area were identified,and the electrical distribution of the Babaoshan mud shale horizon was revealed,which has been proved to be a good geological effect by drilling.The exploration results show that the WFEM has significant effects on the exploration of shale gas occurrence strata,which meets the needs of investigation and evaluation of multi-layered and large-scale shale gas,and plays a good demonstration role in the follow-up shale gas exploration.展开更多
A new modified LuGre friction model is presented for electromagnetic valve actuator system.The modification to the traditional LuGre friction model is made by adding an acceleration-dependent part and a nonlinear cont...A new modified LuGre friction model is presented for electromagnetic valve actuator system.The modification to the traditional LuGre friction model is made by adding an acceleration-dependent part and a nonlinear continuous switch function.The proposed new friction model solves the implementation problems with the traditional LuGre model at high speeds.An improved artificial fish swarm algorithm(IAFSA)method which combines the chaotic search and Gauss mutation operator into traditional artificial fish swarm algorithm is used to identify the parameters in the proposed modified LuGre friction model.The steady state response experiments and dynamic friction experiments are implemented to validate the effectiveness of IAFSA algorithm.The comparisons between the measured dynamic friction forces and the ones simulated with the established mathematic friction model at different frequencies and magnitudes demonstrate that the proposed modified LuGre friction model can give accurate simulation about the dynamic friction characteristics existing in the electromagnetic valve actuator system.The presented modelling and parameter identification methods are applicable for many other high-speed mechanical systems with friction.展开更多
Electromagnetic scattering from targets situated in half space is solved by applying fast inhomogeneous plane wave algorithm combined with a tabulation and interpolation method. The integral equation is set up based o...Electromagnetic scattering from targets situated in half space is solved by applying fast inhomogeneous plane wave algorithm combined with a tabulation and interpolation method. The integral equation is set up based on derivation of dyadic Green＇s functions in this environment. The coupling is divided into nearby region and well-separated region by grouping. The Green＇s function can be divided into two parts： primary term and reflected term. In the well-separated region, the two terms are both expressed as Sommerfeld integral, which can be accelerated by deforming integral path and taking interpolation and extrapolation. For the nearby region, the direct Sommerfeld integral makes the filling of impedance matrix time-expensive. A tabulation and interpolation method is applied to speed up this process. This infinite integral is pre-computed in sampling region, and a two-dimensional table is then set up. The impedance elements can then be obtained by interpolation. Numerical results demonstrate the accuracy and efficiency of this algorithm.展开更多
The existing direction of arrival （DOA） estimation algorithms based on the electromagnetic vector sensors array barely deal with the coexisting of independent and coherent signals. A two-dimensional direction findin...The existing direction of arrival （DOA） estimation algorithms based on the electromagnetic vector sensors array barely deal with the coexisting of independent and coherent signals. A two-dimensional direction finding method using an L-shape electromagnetic vector sensors array is proposed. According to this method, the DOAs of the independent signals and the coherent signals are estimated separately, so that the array aperture can be exploited sufficiently. Firstly, the DOAs of the independent signals are estimated by the estimation of signal parameters via rotational invariance techniques, and the influence of the co- herent signals can be eliminated by utilizing the property of the coherent signals. Then the data covariance matrix containing the information of the coherent signals only is obtained by exploiting the Toeplitz property of the independent signals, and an improved polarimetric angular smoothing technique is proposed to de-correlate the coherent signals. This new method is more practical in actual signal environment than common DOA estimation algorithms and can expand the array aperture. Simulation results are presented to show the estimating performance of the proposed method.展开更多
The Experimental Satellite on Electromagnetism Monitoring(ESEM) was proposed in 2003 and proved in 2013 after 10-years' scientific demonstration. The ESEM mission was proposed to be the first satellite of space-ba...The Experimental Satellite on Electromagnetism Monitoring(ESEM) was proposed in 2003 and proved in 2013 after 10-years' scientific demonstration. The ESEM mission was proposed to be the first satellite of space-based geophysical fields observation system in China with a lot of application prospects in earthquake science, geophysics, space sciences and so on. And coincide with the mission objectives, the satellite decides to use the Circular Sun Synchronous Orbit with an altitude of 507 km and descending node time at 14:00 LT. The payload assemble includes 8 instruments,Search-Coil Magnetometer, Electric Field Detector, High precision Magnetometer, GNSS occupation Receiver, Plasma Analyzer, Langmuir Probe, Energetic Particle Detector, and Three-frequency Transmitter. According to the planned schedule, the satellite is due to be launched in 2016–2017 and will be onboard operated for 5 years.展开更多
To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulate...To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulated discharge flow of steering pump to realize variable assist characteristic as well as uniquely transfer on-demand power from engine to steering pump. The model of ESC was established and the dynamic characteristics of ESC were presented by the way of simulation and experiment. Upon the layout of the assist characteristics, output torque of ESC was derived. Based on the ESC model, the output torque characteristics of ESC were simulated under steering situation and straight driving situation, respectively. The consistency of simulated ESC output torque and the one deduced from assist characteristics verifies the correctness of the ESC dynamic model. To illustrate energy saving characteristics of ESC-HPS, energy consumption comparison of ESC-HPS and conventional HPS was carried out qualitatively and quantitatively. It follows that the energy consumption of ESC-HPS decreases by 50% compared with that of HPS.展开更多
A typical electronic communication system, such as GPS receiver, unmanned aerial vehicle＇s （UAV＇s） data link, and radar, faces multi-dimensional and complicated electromagnetic interference in operating environmen...A typical electronic communication system, such as GPS receiver, unmanned aerial vehicle＇s （UAV＇s） data link, and radar, faces multi-dimensional and complicated electromagnetic interference in operating environment. To measure the anti- interference performance of the electronic communication system in the complicated electromagnetic interference environment, a method of multi-dimensional and complicated electromagnetic interference hardware-in-the-loop simulation in an anechoic room is proposed. It takes into account the characteristics of interference signals and the positional relationship among interference, the receiver and the transmitter of the electronic communication system. It uses the grey relational method and the angular domain mapping error correction method to control the relevant parameters, the microwave switch and so on, thus achieving the approximately actual mapping of the outdoor multi-dimensional and complicated electromagnetic interference in the anechoic room. To verify the effectiveness of this method, the multi-dimensional and complicated electromagnetic interference of the UAV＇s data link is simulated as an example. The results show that the degree of correlation between the calculated signal to interference ratio of the data link receiver in the actual scene and the measured signal to interference ratio of the data link receiver simulated with this method in the anechoic room is 0.968 1, proving that the method is effective for simulating the complicated electromagnetic interference.展开更多
基金National Natural Science Foundation of China (52371171, 52222106, 51971008, 52121001)Fund of National Key Laboratory of Scattering and Radiation (Beijing Institute of Environmental Features)。
文摘[Background and purposes]In recent years,there has been growing attention in academia and industry on the development of high-performance electromagnetic wave(EMW)absorbing materials.However,creating lightweight broadband absorbers remains a challenge in terms of practical applications.EMW absorbing materials primarily rely on the magnetic loss of magnetic materials and/or the dielectric loss of dielectric materials to convert EMW energy into thermal energy for dissipation.Among various magnetic materials,Fe_(3)O_(4) plays an irreplaceable role in EMW absorption due to its high saturation magnetization,low cost and compatible dielectric loss in the gigahertz frequency range.Nevertheless,the high density,large matching thickness and narrow absorption bandwidth of Fe_(3)O_(4) pose significant challenges for practical applications.In contrast,one-dimensional(1D)structures not only retain the characteristic properties of lightweight,chemical stability and high dielectric loss,but also exhibit anisotropic structures and large aspect ratios.Additionally,researchers have found that the minimum reflection loss(RL)of hollow carbon materials with mesopores is nearly four times that of non-porous hollow carbon materials and nine times that of dense carbon materials.According to Maxwell's EMW theory,composites consisting of Fe_(3)O_(4) and one-dimensional(1D)mesoporous carbon materials can leverage their respective advantages by optimizing the composition and structure of the composites to balance u,and Er,thereby enhancing EMW absorption performance.Additionally,numerous studies have demonstrated that composites composed of multi-component heterostructures significantly enhance the EAB.This enhancement is primarily ascribed to the numerous interface polarization losses generated by the additional heterostructure interfaces,which also improve the overall impedance matching of the composites.In this study,we leverage the advantages of magnetic/carbon composites,one-dimensional(1D)mesoporous carbon and multi-component heterostructures to prepare a composite of 1D mesoporous carbon-coated manganese oxide(Mn_(3)O_(4) and MnO,denoted as Mn_(x)O_(y))embedded with Fe_(3)0_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4)).This composite was synthesized and its formation mechanism and microstructure were analyzed in detail.At the same time,the influence of this Mn_(x)O_(y)/C@Fe_(3)O_(4) structure on EMW properties and absorbing performance was further discussed.[Methods]Firstly,MnO_(2) nanowires were synthesized by using a simple hydrothermal method.Then,the MnO_(2) nanowires served as templates for the synthesis of MnO_(2)/PDA@Fe^(3+)composites through the in-situ polymerization of dopamine and Fe^(3+)adsorption.Finally,1D mesoporous carbon-coated manganese oxide composite embedded with Fe_(3)O_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4))composites were obtained after heat treatment at 550℃ in N_(2).The crystal structure of the samples was analyzed using X-ray diffractometer with Cu Ka irradiation.Scanning electron microscopy(SEM)and high-resolution transmission electron microscopy(TEM)were used to observe microstructure and morphology of the samples.Nitrogen sorption measurements were obtained at 77 K on a Quantachrome surface area and pore size analyzer to measure the specific surface area and pore size distribution.XPS analysis was performed on X-ray photoelectron spectrometer with monochromatic Al Ka radiation.Magnetization curves of the samples were recorded with a Quantum Design physical property measurement system(PPMS-9)at room temperature.The electromagnetic parameters of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites were measured using an Agilent N5230C network analyzer in the frequency range of 2-18 GHz.For electromagentic testing,the Mn,Oy/C@Fe34 composites and paraffin wax were mixed at 50°C according to the mass ratio of 15 wt.%,20 wt.%and 25 wt.%,and pressed in a special mold to make coaxial rings(inner diameter=3.04 mm,outer diameter-7 mm),which were denoted as S-1,S-2 and S-3,respectively.[Results]SEM images illustrate the preparation process of iD mesoporous carbon-coated manganese oxide embedded with Fe3O4 nanoparticles composites(Mn_(x)O_(y)/C@Fe_(3)O_(4)).Most of the manganese oxide(Mn,Oy)was reduced to granular after heat treatment,while the outer carbon layer remains its 1D morphology and the carbon layer is interspersed with Fe_(3)O_(4) nanoparticles.The diffraction peaks of MnO_(2) nanowires align well with the body-centered tetragonal a-MnO2.For the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites,the signals of α-MnO_(2) disappears,followed by the emergence of Mn_(3)O_(4) and three prominent diffraction peaks for the cubic MnO.In addition,four weak diffraction peaks correspond to the magnetite Fe_(3)O_(4),consistent with the HRTEM results.The corresponding nitrogen adsorption-desorption isotherm and pore size distribution curve are presented to further analyze the mesoporous structure of composite.The surface composition and element valence states of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite were investigated by using XPS.The polarization relaxation processes were analyzed according to the Debye theory which describes the relationship between e'and e".Besides the polarization loss,the contribution of the conduction loss plays an important role for the overall dielectric loss.The magnetization curve of Mn_(x)O_(y)/C@Fe_(3)O_(4) exhibits typical ferromagnetic behavior.The permittivity parameter(Co),defined as Co=u"(u)^(-2)f^(-1) determine the contribution of eddy current effect to magnetic loss.The tand values are all larger than those of tand,for the three samples,indicating that the loss capacity of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites is mainly derived from the dielectric loss.Although tand,is smaller,it plays an important role in improving the impedance matching of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites.When the filler loading is 15 wt.%,the RL of sample S-1 is about-10.0 dB at the thickness of 1.5 mm with narrow EAB.As the filler loading increased to 20 wt.%,the RL of sample S-2 reached-62.0 dB at a thickness of 2.2 mm and the EAB was 6.4 GHz at a small thickness of 1.7 mm.When the filler loading is further increased to 25 wt.%,the microwave absorption performance of sample S3 decreased significantly with a little region of RL<-10.0 dB at the thickness of 5.0 mm.The values of[Zin/Zol of the three samples at thicknesses of 1.5-5.0 mm were calculated.Due to good impedance matching of S-2,the incident EMW can enter the material and then can be dissipated through dipole polarization loss,interface polarization loss,conduction loss,eddy current loss and natural ferromagnetic resonance loss.[Conclusions]1D Mn_(x)O_(y)/C@Fe_(3)O_(4) was synthesized via a process involving the coating of polydopamine,adsorption of Fe(ll)salts and heat treatment,using MnO_(2) nanowires as templates.The multi-component heterostructure of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite(Mn_(3)O_(4),MnO,Fe_(3)O_(4),and C)enhances the interfacial interactions between the different phases,providing increased interface polarization loss under the action of an alternating electromagnetic field.The numerous defects and terminal groups in the mesoporous carbon provide abundant dipole polarization centers.Additionally,the presence of mesopores reduces the weight of the material while increasing the multiple scattering losses of the electromagnetic waves within the material.The ID carbon structure in the matrix forms a conductive network between adjacent fibers,facilitating electron migration and transition,thereby enhancing conductive loss.The incorporation of magnetic Fe_(3)O_(4) nanoparticles introduces eddy current loss and natural ferromagnetic resonance loss,thus increasing magnetic loss.Moreover,the synergistic effect between dielectric and magnetic losses improves the impedance matching of the material,leading to excellent EMW absorption performance.
基金supported by Major Projects of Shanxi Province (202101030201001)。
文摘Constructing a photoconductive semiconductor switch (PCSS)-metal coil structure, we discovered anew phenomenon of electromagnetic oscillation in vanadium-compensation semi-insulating (VCSI) PCSS. Here thePCSS responds to laser pulse and high-voltage signal while the metal coil generates an oscillating voltage pulseenvelope signal. The generation of this oscillating signal is not related to the input bias voltage of the PCSS, the pulsecircuit components, or the electrode structure of the PCSS, rather it is related to the output characteristic of the PCSS.This physical phenomenon can be explained using the current surge model in photoconducting antenna. Preparingohmic contact electrode on the silicon carbide material forms the PCSS, which generates a large number ofphotogenerated carriers when ultra-fast laser pulses irradiate the surface of the material and Simultaneously applies abias voltage signal between the electrode. At this time inside the PCSS the electric field causes the transient current,radiating electromagnetic wave to the metal coil to generate oscillating signal.
基金supported by the"Fundamental Research Funds for the Central Universities"(Grant No.30924010801).
文摘In this study,the potential application of shaped charge jets as transient antennas for electromagnetic signal transmission was explored and an electromagnetic pulse radiation system with a shaped charge jet as a transient antenna was proposed.During the research,crucial characteristics of the transient antenna formed by a shaped charge with a 30 mm diameter,such as resonant frequency,radiation pattern,and radiation efficiency,were evaluated.The typical shaped charge jet morphology was obtained based on the simulations,in which it could insight the dynamic behavior of the shaped charge jet selected.An equivalent model experiment was employed to test the radiation efficiency,and it showed that a shorting pin loading method could increase the relative bandwidth of the jet antenna to 32.8%,and the experimental results correlate with the theoretical predictions for half-wave dipole antennas reasonably well.Additionally,variations in the diameter of the shaped charge jet were found to affect the input impedance and impedance bandwidth,while the length of the jet influenced the resonant frequency of the antenna.This suggests that altering these parameters can achieve reconfigurability of the jet antenna.
基金supported by the National Natural Science Foundation of China(11172322)
文摘Space electromagnetic docking technology, free of propellant and plume contamination, offers continuous, reversible and synchronous controllability, which is widely applied in the future routine on-orbit servicing missions. Due to the inherent nonlinearities, couplings and uncertainties of an electromagnetic force model, the dynamics and control problems of them are difficult. A new modeling approach for relative motion dynamics with intersatellite force is proposed. To resolve these control problems better, a novel nonlinear control method for soft space electro-magnetic docking is proposed, which combines merits of artificial potential function method, Lyapunov theory and extended state observer. In addition, the angular momentum management problem of space electromagnetic docking and approaches of handling it by exploiting the Earth＇s magnetic torque are investigated. Finally, nonlinear simulation results demonstrate the feasibility of the dynamic model and the novel nonlinear control method.
文摘This paper presents the principle of electromagnetic missile from the mathematical point of view, and verifies rigorously that the radiating power over whole space is limited.
文摘In the earth there exist various forms of natural and artificial electromagnetic fields;the study of their formation, laws of development and practical application constitute the fundamental tasks of the discipline of geoelectromagnetics.The currently app
基金Project(2018R1D1A1B07043399)supported by Basic Science Research Program through the National Research Foundation,Korea
文摘As semiconductor technologies have been shrinking,the speed of circuits,integration density,and the number of I/O interfaces have been significantly increasing.As a consequence,electromagnetic emanation(EME)becomes a critical issue in digital system designs.Electronic devices must meet electromagnetic compatibility(EMC)requirements to ensure that they operate properly,and safely without interference.I/O buffers consume high currents when they operate.The bonding wires,and lead frames are long enough to play as efficient antennas to radiate electromagnetic interference(EMI).Therefore,I/O switching activities significantly contribute to the EMI.In this paper,we evaluate and analyze the impact of I/O switching activities on the EME.We will change the circuit configurations such as the supply voltage for I/O banks,their switching frequency,driving current,and slew rate.Additionally,a trade-off between the switching frequencies and the number of simultaneous switching outputs(SSOs)is also considered in terms of EME.Moreover,we evaluate the electromagnetic emissions that are associated with the different I/O switching patterns.The results show that the electromagnetic emissions associated I/O switching activities depend strongly on their operating parameters and configurations.All the circuit implementations and measurements are carried out on a Xilinx Spartan-3 FPGA.
文摘The rails of electromagnetic railgun can be ablated by the temperature rise due to current concentration.The current distributions on the rails and armature are not only affected by the skin effect,but also influenced by the proximity effect which is rarely mentioned.This paper illustrated the difference between skin effect and proximity effect,and the influencing factors of proximity effect were investigated.Results show that the current is concentrated on the surface around rails due to the skin effect,and the proximity effect exacerbates the current density on the inner surfaces of rails.Decrease in distance from rails enhances the proximity effect,but has nothing to do with the skin effect,which also augments the rail resistance,resulting in temperature rise.It can explain the reason why the ablation is often detected in the small caliber railgun.Research results in this paper can provide support for design and optimization of electromagnetic railgun.
文摘The design of solid armature of railgun should take full account of its operating conditions and material properties because the armature is subjected to dynamic loading conditions and experiences a complicated electrical,thermal and mechanical process in the interior ballistic cycle.In this paper present,we first introduced a multi-physical field model of railgun,followed by several examples to investigate the launching process.Especially,we used the explicit finite element method,in which material nonlinearity and geometric nonlinearity were accounted,to investigate the deform behaviors of solid armature.The results show that the dynamic mechanical process of armature is dependent on the armature geometry,material and exciting electric current.By the numerical simulation,the understanding of the fracture mechanism of solid armature was deepened.
基金This work is supported by the National Key R&D Program of China(No.2017YFB1200800)the National Natural Science Foundation of China(No.11725210,11572281,51827810,51637009)+1 种基金the Fundamental Research Funds for the Central Universities(2018XZZX001-05)the National Student’s Platform for Innovation and Entrepreneurship Training Program(201910335115).
文摘Electromagnetic railgun attracts more and more attention due to its advantage in speed,cost,and obscurity.It is found that the rail should withstand huge mechanical and thermal shocks during the launching operation.The forms of rail failure are accompanied by gouge,grooving,transition,and arc ablation,etc.The service life of the rail has become a bottleneck restricting the development of electromagnetic railgun technology.A series of researches are carried out to solve rail failure,including analysing the failure mechanism and using various advanced rail materials.This paper provides a comprehensive review of rail materials,including material composition,preparation,microstructure,and properties.We begin from a short background of the requirement of the rail material.Then a detailed investigation of rail materials is described,and the performances of those materials are introduced.Finally,further development prospect of rail material is discussed.
基金Project(10974115) supported by the National Natural Science Foundation of China
文摘Facing the problems lack of considering the non-uniform distribution of the static bias magnetic field and computing the panicle displacements in the simulation model of electromagnetic acoustic transducer （EMAT）, a multi-field coupled model was established and the finite element method （FEM） was presented to calculate the entire transduction process. The multi-field coupled model included the static magnetic field, pulsed eddy current field and mechanical field. The FEM equations of the three fields were derived by Garlerkin FEM method. Thus, the entire transduction process of the EMAT was calculated through sequentially coupling the three fields. The transduction process of a Lamb wave EMAT was calculated according to the present model and method. The results show that, by the present method, it is valid to calculate the particle displacement under the given excitation signal and non-uniformly distributed static magnetic field. Calculation error will be brought about if the non-uniform distribution of the static bias magnetic field is neglected.
文摘Switched reluctance motors(SRM)with full-pitch windings and segmental rotors are particularly suitable for the drive systems in aerospace environments because of low wind(oil)resistance and iron losses at high speed.In this paper,the authors have been studying electromagnetic design of this motor.
基金Project(2004ABA110) supported by the Natural Science Foundation of Hubei Province project(471-38300843) supported by the Research Foundation for the Doctoral Program of Wuhan University of Technology
文摘Effect of electromagnetic stirring on microstructure of AZ91-0.8%Ce magnesium alloy was investigated. The results show that electromagnetic stirring causes a change of morphology of α-Mg phase from coarse dendrites to fine rosette-like or spherical shape. Grain size is significantly refined within the range of input voltage 75?125 V, moreover, the optimum input voltage corresponded to the minimum value (64 μm) of grain size is 125 V. Compared to the non-stirred condition, the amount of β-Mg17Al12 precipitate under the stirred condition obviously increases. The grain refinement of AZ91-0.8%Ce alloy is mainly attributed to multiplication of existing grains in the melt caused by forced fluid flow under electromagnetic stirring condition. Addition of 0.8% Ce results in the formation of ‘necking’ at secondary dendrite arm roots of α-Mg crystals, and consequently, it is helpful to increase the number of heterogeneous nucleation.
基金Project(2019-SF-141)supported by Science and Technology Program of Qinghai Province,ChinaProjects(2017042105kc055,2017042014ky014)supported by Geological Exploration Foundation of Qinghai Province,China。
文摘In order to study the distribution of shale gas reservoir in the Babaoshan Basin of Eastern Kunlun,the wide-field electromagnetic(WFEM)survey was carried out to obtain the spatial distribution characteristics of the underground electrical volume resistivity based on the delineation of the scope of the Babaoshan Basin by regional gravity data.The basic characteristics of the basement,basin framework,and extension,vertical change,burial depth of dark mud shale in this area were identified,and the electrical distribution of the Babaoshan mud shale horizon was revealed,which has been proved to be a good geological effect by drilling.The exploration results show that the WFEM has significant effects on the exploration of shale gas occurrence strata,which meets the needs of investigation and evaluation of multi-layered and large-scale shale gas,and plays a good demonstration role in the follow-up shale gas exploration.
基金Project(2015BAG06B00)supported by the National Key Technology Research from Development Program of the Ministry of Science and Technology of China
文摘A new modified LuGre friction model is presented for electromagnetic valve actuator system.The modification to the traditional LuGre friction model is made by adding an acceleration-dependent part and a nonlinear continuous switch function.The proposed new friction model solves the implementation problems with the traditional LuGre model at high speeds.An improved artificial fish swarm algorithm(IAFSA)method which combines the chaotic search and Gauss mutation operator into traditional artificial fish swarm algorithm is used to identify the parameters in the proposed modified LuGre friction model.The steady state response experiments and dynamic friction experiments are implemented to validate the effectiveness of IAFSA algorithm.The comparisons between the measured dynamic friction forces and the ones simulated with the established mathematic friction model at different frequencies and magnitudes demonstrate that the proposed modified LuGre friction model can give accurate simulation about the dynamic friction characteristics existing in the electromagnetic valve actuator system.The presented modelling and parameter identification methods are applicable for many other high-speed mechanical systems with friction.
文摘Electromagnetic scattering from targets situated in half space is solved by applying fast inhomogeneous plane wave algorithm combined with a tabulation and interpolation method. The integral equation is set up based on derivation of dyadic Green＇s functions in this environment. The coupling is divided into nearby region and well-separated region by grouping. The Green＇s function can be divided into two parts： primary term and reflected term. In the well-separated region, the two terms are both expressed as Sommerfeld integral, which can be accelerated by deforming integral path and taking interpolation and extrapolation. For the nearby region, the direct Sommerfeld integral makes the filling of impedance matrix time-expensive. A tabulation and interpolation method is applied to speed up this process. This infinite integral is pre-computed in sampling region, and a two-dimensional table is then set up. The impedance elements can then be obtained by interpolation. Numerical results demonstrate the accuracy and efficiency of this algorithm.
基金supported by the National Natural Science Foundation of China (61102106)the Fundamental Research Funds for the Central Universities (HEUCF1208 HEUCF100801)
文摘The existing direction of arrival （DOA） estimation algorithms based on the electromagnetic vector sensors array barely deal with the coexisting of independent and coherent signals. A two-dimensional direction finding method using an L-shape electromagnetic vector sensors array is proposed. According to this method, the DOAs of the independent signals and the coherent signals are estimated separately, so that the array aperture can be exploited sufficiently. Firstly, the DOAs of the independent signals are estimated by the estimation of signal parameters via rotational invariance techniques, and the influence of the co- herent signals can be eliminated by utilizing the property of the coherent signals. Then the data covariance matrix containing the information of the coherent signals only is obtained by exploiting the Toeplitz property of the independent signals, and an improved polarimetric angular smoothing technique is proposed to de-correlate the coherent signals. This new method is more practical in actual signal environment than common DOA estimation algorithms and can expand the array aperture. Simulation results are presented to show the estimating performance of the proposed method.
文摘The Experimental Satellite on Electromagnetism Monitoring(ESEM) was proposed in 2003 and proved in 2013 after 10-years' scientific demonstration. The ESEM mission was proposed to be the first satellite of space-based geophysical fields observation system in China with a lot of application prospects in earthquake science, geophysics, space sciences and so on. And coincide with the mission objectives, the satellite decides to use the Circular Sun Synchronous Orbit with an altitude of 507 km and descending node time at 14:00 LT. The payload assemble includes 8 instruments,Search-Coil Magnetometer, Electric Field Detector, High precision Magnetometer, GNSS occupation Receiver, Plasma Analyzer, Langmuir Probe, Energetic Particle Detector, and Three-frequency Transmitter. According to the planned schedule, the satellite is due to be launched in 2016–2017 and will be onboard operated for 5 years.
基金Project(51275211)supported by the National Natural Science Foundation of ChinaProject(11KJA580001)supported by the Natural Science Fund for Colleges and Universities in Jiangsu Province,ChinaProject(CXZZ12_0665)supported by the Postgraduate Innovation Natural Science Foundation of Jiangsu Province,China
文摘To improve high-speed road feel and enhance energetic efficiency of hydraulic power steering(HPS) system in heavy-duty vehicles, an electromagnetic slip coupling(ESC) was applied to the steering system, which regulated discharge flow of steering pump to realize variable assist characteristic as well as uniquely transfer on-demand power from engine to steering pump. The model of ESC was established and the dynamic characteristics of ESC were presented by the way of simulation and experiment. Upon the layout of the assist characteristics, output torque of ESC was derived. Based on the ESC model, the output torque characteristics of ESC were simulated under steering situation and straight driving situation, respectively. The consistency of simulated ESC output torque and the one deduced from assist characteristics verifies the correctness of the ESC dynamic model. To illustrate energy saving characteristics of ESC-HPS, energy consumption comparison of ESC-HPS and conventional HPS was carried out qualitatively and quantitatively. It follows that the energy consumption of ESC-HPS decreases by 50% compared with that of HPS.
基金supported by the National Natural Science Foundation of China(61571368)the certain Ministry Foundation(2014607B006)
文摘A typical electronic communication system, such as GPS receiver, unmanned aerial vehicle＇s （UAV＇s） data link, and radar, faces multi-dimensional and complicated electromagnetic interference in operating environment. To measure the anti- interference performance of the electronic communication system in the complicated electromagnetic interference environment, a method of multi-dimensional and complicated electromagnetic interference hardware-in-the-loop simulation in an anechoic room is proposed. It takes into account the characteristics of interference signals and the positional relationship among interference, the receiver and the transmitter of the electronic communication system. It uses the grey relational method and the angular domain mapping error correction method to control the relevant parameters, the microwave switch and so on, thus achieving the approximately actual mapping of the outdoor multi-dimensional and complicated electromagnetic interference in the anechoic room. To verify the effectiveness of this method, the multi-dimensional and complicated electromagnetic interference of the UAV＇s data link is simulated as an example. The results show that the degree of correlation between the calculated signal to interference ratio of the data link receiver in the actual scene and the measured signal to interference ratio of the data link receiver simulated with this method in the anechoic room is 0.968 1, proving that the method is effective for simulating the complicated electromagnetic interference.
