The cavity characteristics in liquid-filled containers caused by high-velocity impacts represent an important area of research in hydrodynamic ram phenomena.The dynamic expansion of the cavity induces liquid pressure ...The cavity characteristics in liquid-filled containers caused by high-velocity impacts represent an important area of research in hydrodynamic ram phenomena.The dynamic expansion of the cavity induces liquid pressure variations,potentially causing catastrophic damage to the container.Current studies mainly focus on non-deforming projectiles,such as fragments,with limited exploration of shaped charge jets.In this paper,a uniquely experimental system was designed to record cavity profiles in behind-armor liquid-filled containers subjected to shaped charge jet impacts.The impact process was then numerically reproduced using the explicit simulation program ANSYS LS-DYNA with the Structured Arbitrary Lagrangian-Eulerian(S-ALE)solver.The formation mechanism,along with the dimensional and shape evolution of the cavity was investigated.Additionally,the influence of the impact kinetic energy of the jet on the cavity characteristics was analyzed.The findings reveal that the cavity profile exhibits a conical shape,primarily driven by direct jet impact and inertial effects.The expansion rates of both cavity length and maximum radius increase with jet impact kinetic energy.When the impact kinetic energy is reduced to 28.2 kJ or below,the length-to-diameter ratio of the cavity ultimately stabilizes at approximately 7.展开更多
Liquid-filled containers(LFC)are widely used to store and transport petroleum,chemical reagents,and other resources.As an important target of military strikes and terrorist bombings,LFC are vulnerable to blast waves a...Liquid-filled containers(LFC)are widely used to store and transport petroleum,chemical reagents,and other resources.As an important target of military strikes and terrorist bombings,LFC are vulnerable to blast waves and fragments.To explore the protective effect of polyurea elastomer on LFC,the damage characteristics of polyurea coated liquid-filled container(PLFC)under the combined loading of blast shock wave and fragments were studied experimentally.The microstructure of the polyurea layer was observed by scanning electron microscopy,and the fracture and self-healing phenomena were analyzed.The simulation approach was used to explain the combined blast-and fragments-induced on the PLFC in detail.Finally,the effects of shock wave and fragment alone and in combination on the damage of PLFC were comprehensively compared.Results showed that the polyurea reduces the perforation rate of the fragment to the LFC,and the self-healing phenomenon could also reduce the liquid loss rate inside the container.The polyurea reduces the degree of depression in the center of the LFC,resulting in a decrease in the distance between adjacent fragments penetrating the LFC,and an increase in the probability of transfixion and fracture between holes.Under the close-in blast,the detonation shock wave reached the LFC before the fragment.Polyurea does not all have an enhanced effect on the protection of LFC.The presence of internal water enhances the anti-blast performance of the container,and the hydrodynamic ram(HRAM)formed by the fragment impacting the water aggravated the plastic deformation of the container.The combined action has an enhancement effect on the deformation of the LFC.The depth of the container depression was 27%higher than that of the blast shock wave alone;thus,it cannot be simply summarized as linear superposition.展开更多
The impact of high-velocity penetrators into liquid-filled containers can generate hydrodynamic ram effects,potentially causing catastrophic structural damage to the container.Previous studies have primarily focused o...The impact of high-velocity penetrators into liquid-filled containers can generate hydrodynamic ram effects,potentially causing catastrophic structural damage to the container.Previous studies have primarily focused on undeformed penetrators,such as fragments or bullets,with limited attention directed toward shaped charge jets.This study investigates the penetration characteristics of shaped charge jets impacting behind-armor liquid-filled containers,with particular emphasis on jet-liquid interactions.A theoretical penetration model incorporating material compressibility and jet stretching was developed based on the virtual origin theory.A high-speed imaging experimental system was designed to capture the jet motion within the container.The impact process was numerically reproduced using ANSYS/LSDYNA,and the effects of standoff and overmatch on jet penetration were analyzed.The results reveal that jet stretching induced by increased standoff enhances the penetration velocity of the jet.A proportional relationship between the stretching factor(λ)and the overmatch parameter(I)was identified,withλranging from approximately 1.22 to 1.38 times I across the studied standoff range(80-220 mm).The findings offer a basis for future studies on the pressure distribution in the liquid and the structural response of containers.展开更多
To evaluate the dynamic behavior of a container crane under seismic loads accurately,the contact state between the wheels and the rails or the ground that significantly affect the seismic response of the structure mus...To evaluate the dynamic behavior of a container crane under seismic loads accurately,the contact state between the wheels and the rails or the ground that significantly affect the seismic response of the structure must be considered elaborately.This paper has proposed a modeling method based on the theory of contact and friction for simulating the nonlinear seismic response of large and flexible structure of a jumbo movable container crane,including the contact problem regarding the wheels attached to the bottom of its legs and the rails on which they ride.These models are used to perform extensive dynamic time-history analysis in order to find out their nonlinear dynamic behavior under various excitation modes.It is found that the presented numerical modeling method simulates the nonlinear seismic response of a container crane quite well.Notably,it can verify and expand our understanding of the seismic behaviors by evaluating response performance for the large seaport cranes.展开更多
When conducting dynamic tests of underground structure by a rigid container, reasonable boundary conditions are one of the essential factors related to the accuracy of test results, especially the artificial boundary ...When conducting dynamic tests of underground structure by a rigid container, reasonable boundary conditions are one of the essential factors related to the accuracy of test results, especially the artificial boundary perpendicular to the excitation direction. On the basis of numerous studies, shaking table tests with four different typical boundaries are performed in this study. The tests consider the seismic intensity and seismic wave types. Then, the simulation effects of the four boundary conditions are evaluated from four aspects as follows: the differential rate of peak acceleration, acceleration curve, similarity of Fourier frequency spectra, and uneven soil settlement in rigid containers. Results show that the simulation effects of the boundary conditions are not only affected by the nature of the boundary material but also related to the seismic intensity, types of seismic waves, and filter characteristic of the filling medium in containers. In comparison with the other three types of boundary condition, foamed polyethylene shows the best simulation effect and its effect decreases gradually with the increase in earthquake intensity. Finally, on the basis of existing studies, the evaluation criteria of boundary effect, the principle for the selection of boundary material type and the thickness of boundary material are discussed and summarized, and the corresponding design methods and suggestions are then provided.展开更多
In the present work,effects of various heat transfer fluids on the discharging performance of a phase change material(PCM) included cylindrical container are numerically assessed during forced convection.The heat tran...In the present work,effects of various heat transfer fluids on the discharging performance of a phase change material(PCM) included cylindrical container are numerically assessed during forced convection.The heat transfer fluid air,hydrogen,water and nanofluid with alumina particles are used and the the geometric variation of the PCM embedded region is also considered.The finite element method is used as the solver.Dynamic features of heat exchange with various phases are explored for different heat transfer fluid types,Reynolds number(between 100 and 300) and PCM embedded region geometric variation(h_(x)between 0.01 d_(1) and 0.65 d_(1),hybetween 0.1 h_(1) and 0.4 h_(1)).It is observed that discharging time is significantly influenced by the heat transfer fluid type while full phase transition time for air is obtained as more than 10 times when hydrogen is utilized as heat transfer fluid.The best performance is achieved with nanofluid.When the PCM integrated region size is reduced,discharging time is generally reduced while due to the form of the geometry,vortex formation is established in the PCM region.This results in performance degeneration at the highest radius and height of the inner cylinder.Discharging time increases by about 12% when radius of the inner cylinder is increased from h_(x)=0.35 d_(1) to h_(x)=0.45 d_(1).Dynamic features of PCM temperature and liquid fraction are affected with Reynolds number while discharging time is reduced by about 48% when configurations with the lowest and highest Reynolds number are compared.展开更多
CIFER software is used to identify steering and roll dynamics of a container ship. In this software, advanced features such as the Chirp-Z transform(CZT) and composite window optimization are applied to the time histo...CIFER software is used to identify steering and roll dynamics of a container ship. In this software, advanced features such as the Chirp-Z transform(CZT) and composite window optimization are applied to the time history of steering and roll dynamics to extract high quality frequency responses. From the extracted frequency responses, two linear transfer functions of Nomoto model are fitted for yaw and roll dynamics of the vessel. Based on the identified Nomoto model, a PID heading controller and a Kalman filter observer are constructed. The simulation results of heading controller for line of sight(LOS) waypoint guidance show excellent tracking of pilot inputs in the presence of wave induced motions and forces.展开更多
To study the aerodynamic performance of a new six-axis X2K double-deck container vehicle, numerical simulation was done based on three-dimensional, steady Navier-Stokes equations and k-e turbulence model. The results ...To study the aerodynamic performance of a new six-axis X2K double-deck container vehicle, numerical simulation was done based on three-dimensional, steady Navier-Stokes equations and k-e turbulence model. The results show that the pressure on the front surface of vehicle is positive, and others are negative. The maximum negative one appears as a ＂gate＂ shape on front surfaces. The pressure on vehicle increases with train speed, and pressure on vehicles with cross-loaded structure is smaller than that without it. The airflow around vehicles is symmetrical about train vertical axis, and the flow velocity decreases gradually along the axis to ground. Airflow around vehicles with cross-loaded structure is weaker than that without the structure. The aerodynamic drag increases linearly with the train speed, and it is minimum for the mid-vehicle. The linear coefficient for mid-vehicle without cross-loaded structure is 29.75, nearly one time larger than that with the structure valued as 15.425. So, from the view-point of aerodynamic drag, the cross-loaded structure is more reasonable for the six-axis X2K double-deck container vehicle.展开更多
Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the co...Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the conditions of COFCC with n(O)-n(C) (molar ratio) as 1.00-0.84 and n(SiO2)-n(CaO) as 1.00-0.39, the samples were heated by 10 kW microwave power to reach the given temperatures and held for different times respectively. The results show that the low-C-Cr ferrochromium metal phase in the reduced materials forms before the high-C-Cr ferrochromium metal phase does. With increasing temperature the C content of ferrochromium metals is in a positive correlation with the content of Cr. The C content of ferrochromium metal in reduced materials is 0-10.07% with an average value of 4.68%. With the increase of holding time the Cr content in ferrochromium metals is in a negative correlation with the content of C, while the content of Fe changes in the contrary way. In the microwave field the kinetic conditions of carburization are closely related with the temperature of microwave heating, holding time and carbon fitting ratio.展开更多
A method of recovering indium from complex smelting residue containing indium was investiga ted. Indium was extracted by technique of low acid leaching and solvent extraction. The conditions of separating iron and ind...A method of recovering indium from complex smelting residue containing indium was investiga ted. Indium was extracted by technique of low acid leaching and solvent extraction. The conditions of separating iron and indium were studied and the optimal conditions were determined. When the residue is two class countercurrent leached with 2 mol/L H 2SO 4 and 30 40 g/L NaCl at 100 ℃, the leaching rate of indium is 80%. The extraction rate of indium is over 98% and that of iron is less than 5% after it is third class countercurrent extracted by P204, and when sulfonated kerosene is used as solvent, acidity in aqueous phase remains the same as that of leaching liquid, and phase is for 1∶3. Using 2 mol/L HCl as back extraction agent, with phase ratio being 5∶1, by third class countercurrent back extraction, the back extraction rate of indium is over 99%, but that of iron is very low, which can meet the need of separating indium and iron.展开更多
Pelletization is one of useful processes for the agglomeration of iron ore or concentrates. However, manganese ore fines are mainly agglomerated by sintering due to its high combined water which adversely affects the ...Pelletization is one of useful processes for the agglomeration of iron ore or concentrates. However, manganese ore fines are mainly agglomerated by sintering due to its high combined water which adversely affects the roasting performance of pellets. In this work, high pressure roll grinding(HPRG) process and optimization of temperature elevation system were investigated to improve the strength of fired manganese ore pellets. It is shown that the manganese ore possesses good ballability after being pretreated by HPRG twice, and good green balls were produced under the conditions of blending 2.0% bentonite in the feed, balling for 7 min at 16.00% moisture. High quality roasted pellets with the compressive strength of 2711 N per pellet were manufactured through preheating at 1050 °C for 10 min and firing at 1335 °C for 15 min by controlling the cracks formation. The fired manganese pellets keep the strength by the solid interconnection of recrystallized pyrolusite grains and the binding of manganite liquid phase which filled the pores and clearance among minerals. The product pellets contain high Mn grade and low impurities, and can be used to smelt ferromanganese, which provides a possible way to use imported manganese ore fines containing high combined water to produce high value ferromanganese.展开更多
The flow stress behavior of Al-3.5Cu-1.5Li-0.25(Sc+Zr) alloy during hot compression deformation was studied by isothermal compression test using Gleeble-1500 thermal-mechanical simulator. Compression tests were prefor...The flow stress behavior of Al-3.5Cu-1.5Li-0.25(Sc+Zr) alloy during hot compression deformation was studied by isothermal compression test using Gleeble-1500 thermal-mechanical simulator. Compression tests were preformed in the temperature range of 653-773 K and in the strain rate range of 0.001-10 s-1 up to a true plastic strain of 0.7. The results indicate that the flow stress of the alloy increases with increasing strain rate at a given temperature,and decreases with increasing temperature at a given imposed strain rate. The relationship between the flow stress and the strain rate and the temperature was derived by analyzing the experimental data. The flow stress is in a hyperbolic sine relationship with the strain rate,and in an Arrhenius relationship with the temperature,which imply that the process of plastic deformation at an elevated temperature for this material is thermally activated. The flow stress of the alloy during the elevated temperature deformation can be represented by a Zener-Hollomon parameter with the inclusion of the Arrhenius term. The values of n,α and A in the analytical expressions of flow stress σ are fitted to be 5.62,0.019 MPa-1 and 1.51×1016 s-1,respectively. The hot deformation activation energy is 240.85 kJ/mol.展开更多
An innovative multi-layer composite explosion containment vessel(CECV)utilizing a sliding steel platealuminum honeycomb-fiber cloth sandwich is put forward to improve the anti-explosion capacity of a conventional sing...An innovative multi-layer composite explosion containment vessel(CECV)utilizing a sliding steel platealuminum honeycomb-fiber cloth sandwich is put forward to improve the anti-explosion capacity of a conventional single-layer explosion containment vessel(SECV).Firstly,a series of experiments and finite element(FE)simulations of internal explosions are implemented to understand the basic anti-explosion characteristics of a SECV and the rationality of the computational models and methods is verified by the comparison between the experimental results and simulation results.Based on this,the CECV is designed in detail and a variety of FE simulations are carried out to investigate effects of the sandwich structure,the explosive quantity and the laying mode of the fiber cloth on anti-explosion performance and dynamic response of the CECV under internal explosions.Simulation results indicate that the end cover is the critical position for both the SECV and CECV.The maximum pressure of the explosion shock wave and the maximum strain of the CECV can be extremely declined compared to those of the SECV.As a result,the explosive quantity the CECV can sustain is up to 20 times of that the SECV can sustain.Besides,as the explosive quantity increases,the internal pressure of the CECV keeps growing and the plastic deformation and failure of the sandwich structure become more and more severe,yielding plastic strain of the CECV in addition to elastic strain.The results also reveal that the laying angles of the fiber cloth's five layers have an impact on the anti-explosion performance of the CECV.For example,the CECV with fiber cloth layered in 0°/45°/90°/45°/0°mode has the optimal anti-capacity,compared to 0°/0°/0°/0°/0°and 0°/30°/60°/30°/0°modes.Overall,owing to remarkable anti-explosion capacity,this CECV can be regarded as a promising candidate for explosion resistance.展开更多
The effects of silver sulfide (Ag 2S) on the bioleaching of chalcopyrite and pyrite were investigated in this paper. It has been shown that Ag 2S enhanced the yields of bioleaching of chalcopyrite but inhibited the bi...The effects of silver sulfide (Ag 2S) on the bioleaching of chalcopyrite and pyrite were investigated in this paper. It has been shown that Ag 2S enhanced the yields of bioleaching of chalcopyrite but inhibited the bio oxidation of pyrite. The addition of Ag 2S selectively increased the copper dissolution from the chalcopyrite containing ores in shake flasks with a recovery of 85.3% compared with 24.3% without Ag 2S, while slightly decreased the iron yields from 51% to 41.8%. The copper extraction of the chalcoopyrite containing waste rock in column leaching charged with 18 kg mass increased up to 21.7% in the presence of Ag 2S, while only 3.4% in the absence of the catalyst. The mechanism of Ag 2S catalysis could be explained well by the "Mixed potential model".展开更多
The effect of forging on the microstructure and texture evolution of a high Nb containing Ti-45Al-7Nb-0.3W(at.%)alloy was investigated by X-ray diffractometer(XRD),scanning electron microscopy(SEM),and transmission el...The effect of forging on the microstructure and texture evolution of a high Nb containing Ti-45Al-7Nb-0.3W(at.%)alloy was investigated by X-ray diffractometer(XRD),scanning electron microscopy(SEM),and transmission electron microscopy(TEM).The results show that the as-cast alloy is mainly composed of α_(2)/γ lamellar colonies with a mean size of 70μm,but the hot-forged pancake displays a near duplex microstructure(DP).Kinking and bending of lamellar colonies,deformation twinning and dynamic recrystallization(DRX)occur during hot forging.Meanwhile,dense dislocations in theβphase after forging suggest that the high-temperature β phase with a disordered structure is favorable for improving the hot-workability of the alloy.Unlike the common TiAl casting texture,the solidification process of the investigated as-cast alloy with high Nb content is completely via the β phase region,resulting in the formation of a<110>γ fiber texture where the<110>γ aligns parallel to the heat-flow direction.In comparison,the relatively strong<001>and weak<302>texture components in the as-forged alloy are attributed to the deformation twinning.After annealing,static recrystallization occurs at the twin boundary and intersections,which weakens the deformation texture.展开更多
基金financial support from the National Natural Science Foundation of China(Grant No.11572159).
文摘The cavity characteristics in liquid-filled containers caused by high-velocity impacts represent an important area of research in hydrodynamic ram phenomena.The dynamic expansion of the cavity induces liquid pressure variations,potentially causing catastrophic damage to the container.Current studies mainly focus on non-deforming projectiles,such as fragments,with limited exploration of shaped charge jets.In this paper,a uniquely experimental system was designed to record cavity profiles in behind-armor liquid-filled containers subjected to shaped charge jet impacts.The impact process was then numerically reproduced using the explicit simulation program ANSYS LS-DYNA with the Structured Arbitrary Lagrangian-Eulerian(S-ALE)solver.The formation mechanism,along with the dimensional and shape evolution of the cavity was investigated.Additionally,the influence of the impact kinetic energy of the jet on the cavity characteristics was analyzed.The findings reveal that the cavity profile exhibits a conical shape,primarily driven by direct jet impact and inertial effects.The expansion rates of both cavity length and maximum radius increase with jet impact kinetic energy.When the impact kinetic energy is reduced to 28.2 kJ or below,the length-to-diameter ratio of the cavity ultimately stabilizes at approximately 7.
基金supported by the National Natural Science Foundation of China(Grant Nos.12102480,52278543 and 51978660)Natural Science Foundation of Jiangsu Province(Grant No.BK20231489)。
文摘Liquid-filled containers(LFC)are widely used to store and transport petroleum,chemical reagents,and other resources.As an important target of military strikes and terrorist bombings,LFC are vulnerable to blast waves and fragments.To explore the protective effect of polyurea elastomer on LFC,the damage characteristics of polyurea coated liquid-filled container(PLFC)under the combined loading of blast shock wave and fragments were studied experimentally.The microstructure of the polyurea layer was observed by scanning electron microscopy,and the fracture and self-healing phenomena were analyzed.The simulation approach was used to explain the combined blast-and fragments-induced on the PLFC in detail.Finally,the effects of shock wave and fragment alone and in combination on the damage of PLFC were comprehensively compared.Results showed that the polyurea reduces the perforation rate of the fragment to the LFC,and the self-healing phenomenon could also reduce the liquid loss rate inside the container.The polyurea reduces the degree of depression in the center of the LFC,resulting in a decrease in the distance between adjacent fragments penetrating the LFC,and an increase in the probability of transfixion and fracture between holes.Under the close-in blast,the detonation shock wave reached the LFC before the fragment.Polyurea does not all have an enhanced effect on the protection of LFC.The presence of internal water enhances the anti-blast performance of the container,and the hydrodynamic ram(HRAM)formed by the fragment impacting the water aggravated the plastic deformation of the container.The combined action has an enhancement effect on the deformation of the LFC.The depth of the container depression was 27%higher than that of the blast shock wave alone;thus,it cannot be simply summarized as linear superposition.
基金the financial support from the National Natural Science Foundation of China(Grant No.11572159)。
文摘The impact of high-velocity penetrators into liquid-filled containers can generate hydrodynamic ram effects,potentially causing catastrophic structural damage to the container.Previous studies have primarily focused on undeformed penetrators,such as fragments or bullets,with limited attention directed toward shaped charge jets.This study investigates the penetration characteristics of shaped charge jets impacting behind-armor liquid-filled containers,with particular emphasis on jet-liquid interactions.A theoretical penetration model incorporating material compressibility and jet stretching was developed based on the virtual origin theory.A high-speed imaging experimental system was designed to capture the jet motion within the container.The impact process was numerically reproduced using ANSYS/LSDYNA,and the effects of standoff and overmatch on jet penetration were analyzed.The results reveal that jet stretching induced by increased standoff enhances the penetration velocity of the jet.A proportional relationship between the stretching factor(λ)and the overmatch parameter(I)was identified,withλranging from approximately 1.22 to 1.38 times I across the studied standoff range(80-220 mm).The findings offer a basis for future studies on the pressure distribution in the liquid and the structural response of containers.
基金National Natural Science Foundation of China(No.51275369)
文摘To evaluate the dynamic behavior of a container crane under seismic loads accurately,the contact state between the wheels and the rails or the ground that significantly affect the seismic response of the structure must be considered elaborately.This paper has proposed a modeling method based on the theory of contact and friction for simulating the nonlinear seismic response of large and flexible structure of a jumbo movable container crane,including the contact problem regarding the wheels attached to the bottom of its legs and the rails on which they ride.These models are used to perform extensive dynamic time-history analysis in order to find out their nonlinear dynamic behavior under various excitation modes.It is found that the presented numerical modeling method simulates the nonlinear seismic response of a container crane quite well.Notably,it can verify and expand our understanding of the seismic behaviors by evaluating response performance for the large seaport cranes.
基金Projects(51978669,U1734208)supported by the National Natural Science Foundation of ChinaProject(2018JJ3657)supported by the Natural Science Foundation of Hunan Province,China
文摘When conducting dynamic tests of underground structure by a rigid container, reasonable boundary conditions are one of the essential factors related to the accuracy of test results, especially the artificial boundary perpendicular to the excitation direction. On the basis of numerous studies, shaking table tests with four different typical boundaries are performed in this study. The tests consider the seismic intensity and seismic wave types. Then, the simulation effects of the four boundary conditions are evaluated from four aspects as follows: the differential rate of peak acceleration, acceleration curve, similarity of Fourier frequency spectra, and uneven soil settlement in rigid containers. Results show that the simulation effects of the boundary conditions are not only affected by the nature of the boundary material but also related to the seismic intensity, types of seismic waves, and filter characteristic of the filling medium in containers. In comparison with the other three types of boundary condition, foamed polyethylene shows the best simulation effect and its effect decreases gradually with the increase in earthquake intensity. Finally, on the basis of existing studies, the evaluation criteria of boundary effect, the principle for the selection of boundary material type and the thickness of boundary material are discussed and summarized, and the corresponding design methods and suggestions are then provided.
文摘In the present work,effects of various heat transfer fluids on the discharging performance of a phase change material(PCM) included cylindrical container are numerically assessed during forced convection.The heat transfer fluid air,hydrogen,water and nanofluid with alumina particles are used and the the geometric variation of the PCM embedded region is also considered.The finite element method is used as the solver.Dynamic features of heat exchange with various phases are explored for different heat transfer fluid types,Reynolds number(between 100 and 300) and PCM embedded region geometric variation(h_(x)between 0.01 d_(1) and 0.65 d_(1),hybetween 0.1 h_(1) and 0.4 h_(1)).It is observed that discharging time is significantly influenced by the heat transfer fluid type while full phase transition time for air is obtained as more than 10 times when hydrogen is utilized as heat transfer fluid.The best performance is achieved with nanofluid.When the PCM integrated region size is reduced,discharging time is generally reduced while due to the form of the geometry,vortex formation is established in the PCM region.This results in performance degeneration at the highest radius and height of the inner cylinder.Discharging time increases by about 12% when radius of the inner cylinder is increased from h_(x)=0.35 d_(1) to h_(x)=0.45 d_(1).Dynamic features of PCM temperature and liquid fraction are affected with Reynolds number while discharging time is reduced by about 48% when configurations with the lowest and highest Reynolds number are compared.
文摘CIFER software is used to identify steering and roll dynamics of a container ship. In this software, advanced features such as the Chirp-Z transform(CZT) and composite window optimization are applied to the time history of steering and roll dynamics to extract high quality frequency responses. From the extracted frequency responses, two linear transfer functions of Nomoto model are fitted for yaw and roll dynamics of the vessel. Based on the identified Nomoto model, a PID heading controller and a Kalman filter observer are constructed. The simulation results of heading controller for line of sight(LOS) waypoint guidance show excellent tracking of pilot inputs in the presence of wave induced motions and forces.
基金Project(50975289) supported by the National Natural Science Foundation of ChinaProject(2009J007-C) supported by the Technological Research and Development Program of the Ministry of Railways,ChinaProject(CX2010B122) supported by Hunan Provincial Innovation Foundation for Postgraduate Students,China
文摘To study the aerodynamic performance of a new six-axis X2K double-deck container vehicle, numerical simulation was done based on three-dimensional, steady Navier-Stokes equations and k-e turbulence model. The results show that the pressure on the front surface of vehicle is positive, and others are negative. The maximum negative one appears as a ＂gate＂ shape on front surfaces. The pressure on vehicle increases with train speed, and pressure on vehicles with cross-loaded structure is smaller than that without it. The airflow around vehicles is symmetrical about train vertical axis, and the flow velocity decreases gradually along the axis to ground. Airflow around vehicles with cross-loaded structure is weaker than that without the structure. The aerodynamic drag increases linearly with the train speed, and it is minimum for the mid-vehicle. The linear coefficient for mid-vehicle without cross-loaded structure is 29.75, nearly one time larger than that with the structure valued as 15.425. So, from the view-point of aerodynamic drag, the cross-loaded structure is more reasonable for the six-axis X2K double-deck container vehicle.
基金Project(50474083) supported by the National Natural Science Foundation of ChinaProject supported by the Baoshan Iron & Steel Co. Ltd. of China
文摘Chromium ore fines containing coal (COFCC) can be rapidly heated by microwave to conduct the voluminal reduction, which lays a foundation of getting sponge ferrochromium powders with a lower content of C. Under the conditions of COFCC with n(O)-n(C) (molar ratio) as 1.00-0.84 and n(SiO2)-n(CaO) as 1.00-0.39, the samples were heated by 10 kW microwave power to reach the given temperatures and held for different times respectively. The results show that the low-C-Cr ferrochromium metal phase in the reduced materials forms before the high-C-Cr ferrochromium metal phase does. With increasing temperature the C content of ferrochromium metals is in a positive correlation with the content of Cr. The C content of ferrochromium metal in reduced materials is 0-10.07% with an average value of 4.68%. With the increase of holding time the Cr content in ferrochromium metals is in a negative correlation with the content of C, while the content of Fe changes in the contrary way. In the microwave field the kinetic conditions of carburization are closely related with the temperature of microwave heating, holding time and carbon fitting ratio.
文摘A method of recovering indium from complex smelting residue containing indium was investiga ted. Indium was extracted by technique of low acid leaching and solvent extraction. The conditions of separating iron and indium were studied and the optimal conditions were determined. When the residue is two class countercurrent leached with 2 mol/L H 2SO 4 and 30 40 g/L NaCl at 100 ℃, the leaching rate of indium is 80%. The extraction rate of indium is over 98% and that of iron is less than 5% after it is third class countercurrent extracted by P204, and when sulfonated kerosene is used as solvent, acidity in aqueous phase remains the same as that of leaching liquid, and phase is for 1∶3. Using 2 mol/L HCl as back extraction agent, with phase ratio being 5∶1, by third class countercurrent back extraction, the back extraction rate of indium is over 99%, but that of iron is very low, which can meet the need of separating indium and iron.
基金Project(2011GH561685)supported by the China Torch Program
文摘Pelletization is one of useful processes for the agglomeration of iron ore or concentrates. However, manganese ore fines are mainly agglomerated by sintering due to its high combined water which adversely affects the roasting performance of pellets. In this work, high pressure roll grinding(HPRG) process and optimization of temperature elevation system were investigated to improve the strength of fired manganese ore pellets. It is shown that the manganese ore possesses good ballability after being pretreated by HPRG twice, and good green balls were produced under the conditions of blending 2.0% bentonite in the feed, balling for 7 min at 16.00% moisture. High quality roasted pellets with the compressive strength of 2711 N per pellet were manufactured through preheating at 1050 °C for 10 min and firing at 1335 °C for 15 min by controlling the cracks formation. The fired manganese pellets keep the strength by the solid interconnection of recrystallized pyrolusite grains and the binding of manganite liquid phase which filled the pores and clearance among minerals. The product pellets contain high Mn grade and low impurities, and can be used to smelt ferromanganese, which provides a possible way to use imported manganese ore fines containing high combined water to produce high value ferromanganese.
基金Project(2002AA305104) supported by the National High-Tech Research and Development Program of China
文摘The flow stress behavior of Al-3.5Cu-1.5Li-0.25(Sc+Zr) alloy during hot compression deformation was studied by isothermal compression test using Gleeble-1500 thermal-mechanical simulator. Compression tests were preformed in the temperature range of 653-773 K and in the strain rate range of 0.001-10 s-1 up to a true plastic strain of 0.7. The results indicate that the flow stress of the alloy increases with increasing strain rate at a given temperature,and decreases with increasing temperature at a given imposed strain rate. The relationship between the flow stress and the strain rate and the temperature was derived by analyzing the experimental data. The flow stress is in a hyperbolic sine relationship with the strain rate,and in an Arrhenius relationship with the temperature,which imply that the process of plastic deformation at an elevated temperature for this material is thermally activated. The flow stress of the alloy during the elevated temperature deformation can be represented by a Zener-Hollomon parameter with the inclusion of the Arrhenius term. The values of n,α and A in the analytical expressions of flow stress σ are fitted to be 5.62,0.019 MPa-1 and 1.51×1016 s-1,respectively. The hot deformation activation energy is 240.85 kJ/mol.
基金supported by the National Natural Science Foundation of China (Grant No.11902157)Natural Science Foundation of Jiangsu Province (Grant No.BK20180417)the Scientific and Technological Innovation Project of Army Engineering Univeristy of PLA (Grant No.KYGYZXJK150025)。
文摘An innovative multi-layer composite explosion containment vessel(CECV)utilizing a sliding steel platealuminum honeycomb-fiber cloth sandwich is put forward to improve the anti-explosion capacity of a conventional single-layer explosion containment vessel(SECV).Firstly,a series of experiments and finite element(FE)simulations of internal explosions are implemented to understand the basic anti-explosion characteristics of a SECV and the rationality of the computational models and methods is verified by the comparison between the experimental results and simulation results.Based on this,the CECV is designed in detail and a variety of FE simulations are carried out to investigate effects of the sandwich structure,the explosive quantity and the laying mode of the fiber cloth on anti-explosion performance and dynamic response of the CECV under internal explosions.Simulation results indicate that the end cover is the critical position for both the SECV and CECV.The maximum pressure of the explosion shock wave and the maximum strain of the CECV can be extremely declined compared to those of the SECV.As a result,the explosive quantity the CECV can sustain is up to 20 times of that the SECV can sustain.Besides,as the explosive quantity increases,the internal pressure of the CECV keeps growing and the plastic deformation and failure of the sandwich structure become more and more severe,yielding plastic strain of the CECV in addition to elastic strain.The results also reveal that the laying angles of the fiber cloth's five layers have an impact on the anti-explosion performance of the CECV.For example,the CECV with fiber cloth layered in 0°/45°/90°/45°/0°mode has the optimal anti-capacity,compared to 0°/0°/0°/0°/0°and 0°/30°/60°/30°/0°modes.Overall,owing to remarkable anti-explosion capacity,this CECV can be regarded as a promising candidate for explosion resistance.
文摘The effects of silver sulfide (Ag 2S) on the bioleaching of chalcopyrite and pyrite were investigated in this paper. It has been shown that Ag 2S enhanced the yields of bioleaching of chalcopyrite but inhibited the bio oxidation of pyrite. The addition of Ag 2S selectively increased the copper dissolution from the chalcopyrite containing ores in shake flasks with a recovery of 85.3% compared with 24.3% without Ag 2S, while slightly decreased the iron yields from 51% to 41.8%. The copper extraction of the chalcoopyrite containing waste rock in column leaching charged with 18 kg mass increased up to 21.7% in the presence of Ag 2S, while only 3.4% in the absence of the catalyst. The mechanism of Ag 2S catalysis could be explained well by the "Mixed potential model".
基金Projects(52274402,52174381)supported by the National Natural Science Foundation of China。
文摘The effect of forging on the microstructure and texture evolution of a high Nb containing Ti-45Al-7Nb-0.3W(at.%)alloy was investigated by X-ray diffractometer(XRD),scanning electron microscopy(SEM),and transmission electron microscopy(TEM).The results show that the as-cast alloy is mainly composed of α_(2)/γ lamellar colonies with a mean size of 70μm,but the hot-forged pancake displays a near duplex microstructure(DP).Kinking and bending of lamellar colonies,deformation twinning and dynamic recrystallization(DRX)occur during hot forging.Meanwhile,dense dislocations in theβphase after forging suggest that the high-temperature β phase with a disordered structure is favorable for improving the hot-workability of the alloy.Unlike the common TiAl casting texture,the solidification process of the investigated as-cast alloy with high Nb content is completely via the β phase region,resulting in the formation of a<110>γ fiber texture where the<110>γ aligns parallel to the heat-flow direction.In comparison,the relatively strong<001>and weak<302>texture components in the as-forged alloy are attributed to the deformation twinning.After annealing,static recrystallization occurs at the twin boundary and intersections,which weakens the deformation texture.
