Based on microstructure analysis,diffusion theory,and hot deformation experiments,the solidification microstructure and element segregation of the Alloy 625 Plus ingot,the diffusion kinetics of Ti,Nb,and Mo during hom...Based on microstructure analysis,diffusion theory,and hot deformation experiments,the solidification microstructure and element segregation of the Alloy 625 Plus ingot,the diffusion kinetics of Ti,Nb,and Mo during homogenization and the hot deformation behavior of the homogenized ingot were investigated in this study.The results indicate that:(1)the solidified ingot exhibits a typical dendritic microstructure,and significant element segregation occurs,leading to the presence of Ti,Nb,and Mo-rich precipitates in the interdendritic region;(2)Following homogenization,the degree of element segregation in the ingot is significantly reduced.The diffusion coefficients(D)of Ti,Nb,and Mo under various homogenization conditions were calculated.Subsequently,the diffusion constants(D_(0))and activation energies(Q)of Ti,Nb,and Mo were obtained to be 0.01432,0.00397 and 0.00195 cm^(2)/s and 244.851,230.312,and 222.125 kJ/mol,respectively.Finally,the diffusion kinetics formulas for Ti,Nb,and Mo in Alloy 625 Plus were established.After homogenization at 1220℃for 8 h,the alloy exhibits low deformation resistance,a high degree of recrystallization,and optimal deformation coordination ability.Therefore,this represents a rational single-stage homogenization process.展开更多
In this study, to meet the development and application requirements for high-strength and hightoughness energetic structural materials, a representative volume element of a TA15 matrix embedded with a TaZrNb sphere wa...In this study, to meet the development and application requirements for high-strength and hightoughness energetic structural materials, a representative volume element of a TA15 matrix embedded with a TaZrNb sphere was designed and fabricated via diffusion bonding. The mechanisms of the microstructural evolution of the TaZrNb/TA15 interface were investigated via SEM, EBSD, EDS, and XRD.Interface mechanical property tests and in-situ tensile tests were conducted on the sphere-containing structure, and an equivalent tensile-strength model was established for the structure. The results revealed that the TA15 titanium alloy and joint had high density and no pores or cracks. The thickness of the planar joint was approximately 50-60 μm. The average tensile and shear strengths were 767 MPa and 608 MPa, respectively. The thickness of the spherical joint was approximately 60 μm. The Zr and Nb elements in the joint diffused uniformly and formed strong bonds with Ti without forming intermetallic compounds. The interface exhibited submicron grain refinement and a concave-convex interlocking structure. The tensile fracture surface primarily exhibited intergranular fracture combined with some transgranular fracture, which constituted a quasi-brittle fracture mode. The shear fracture surface exhibited brittle fracture with regular arrangements of furrows. Internal fracture occurred along the spherical interface, as revealed by advanced in-situ X-ray microcomputed tomography. The experimental results agreed well with the theoretical predictions, indicating that the high-strength interface contributes to the overall strength and toughness of the sphere-containing structure.展开更多
Recently,foamed polymers have been widely used in the repair of underground engineering disasters by grouting(trenchless technology)due to controllable gelation time and self-expansion.However,the grouting process bec...Recently,foamed polymers have been widely used in the repair of underground engineering disasters by grouting(trenchless technology)due to controllable gelation time and self-expansion.However,the grouting process becomes more complicated due to the complex geological conditions and the self-expansion of slurry.Therefore,this paper adopts a self-made visual experimental device with peripheral pressure and water plugging rate(WPR)monitoring functions to study the influence of main influencing parameters(particle size distribution,grouting amount and dynamic water pump pressure(DWPP))on the spatiotemporal distribution of slurry WPR and diffusion dynamic response(peripheral pressure).The results show that:When grouting amount is 563 g and DWPP is 0.013 MPa,the expansion force of the slurry in the diffusion process is dominant and can significantly change the local sand and gravel skeleton structure.When grouting amount is 563 g,DWPP is 0.013 MPa,and particle size distribution type isⅢ,the flow time of the polymer is shortened,the pores of the gravel are rapidly blocked.Then,the peripheral pressure decreases rapidly with the increase of the distance,and the time to reach the inflection point WPR is shortened.The instantaneous blockage of the pores leads to the delayed transmission of flow field blockage information.展开更多
Effects of ultrasonic bonding parameters on atomic diffusion, microstructure at the Al-Au interface, and shear strength of Al-Au ultrasonic bonding were investigated by the combining experiments and finite element (FE...Effects of ultrasonic bonding parameters on atomic diffusion, microstructure at the Al-Au interface, and shear strength of Al-Au ultrasonic bonding were investigated by the combining experiments and finite element (FE) simulation. The quantitative model of atomic diffusion, which is related to the ultrasonic bonding parameters, time and distance, is established to calculate the atomic diffusion of the Al-Au interface. The maximum relative error between the calculated and experimental fraction of Al atom is 7.35%, indicating high prediction accuracy of this model. During the process of ultrasonic bonding, Au8Al3 is the main intermetallic compound (IMC) at the Al-Au interface. With larger bonding forces, higher ultrasonic powers and longer bonding time, it is more difficult to remove the oxide particles from the Al-Au interface, which hinders the atomic diffusion. Therefore, the complicated stress state and the existence of oxide particles both promotes the formation of holes. The shear strength of Al-Au ultrasonic bonding increases with increasing bonding force, ultrasonic power and bonding time. However, combined with the presence of holes at especial parameters, the optimal ultrasonic bonding parameter is confirmed to be a bonding force of 23 gf, ultrasonic power of 75 mW and bonding time of 21 ms.展开更多
The development of InGaAs/InP single-photon avalanche photodiodes(SPADs)necessitates the utiliza-tion of a two-element diffusion technique to achieve accurate manipulation of the multiplication width and the dis-tribu...The development of InGaAs/InP single-photon avalanche photodiodes(SPADs)necessitates the utiliza-tion of a two-element diffusion technique to achieve accurate manipulation of the multiplication width and the dis-tribution of its electric field.Regarding the issue of accurately predicting the depth of diffusion in InGaAs/InP SPAD,simulation analysis and device development were carried out,focusing on the dual diffusion behavior of zinc atoms.A formula of X_(j)=k√t-t_(0)+c to quantitatively predict the diffusion depth is obtained by fitting the simulated twice-diffusion depths based on a two-dimensional(2D)model.The 2D impurity morphologies and the one-dimensional impurity profiles for the dual-diffused region are characterized by using scanning electron micros-copy and secondary ion mass spectrometry as a function of the diffusion depth,respectively.InGaAs/InP SPAD devices with different dual-diffusion conditions are also fabricated,which show breakdown behaviors well consis-tent with the simulated results under the same junction geometries.The dark count rate(DCR)of the device de-creased as the multiplication width increased,as indicated by the results.DCRs of 2×10^(6),1×10^(5),4×10^(4),and 2×10^(4) were achieved at temperatures of 300 K,273 K,263 K,and 253 K,respectively,with a bias voltage of 3 V,when the multiplication width was 1.5µm.These results demonstrate an effective prediction route for accu-rately controlling the dual-diffused zinc junction geometry in InP-based planar device processing.展开更多
In this paper,we investigate the strong Feller property of stochastic differential equations(SDEs)with super-linear drift and Hölder diffusion coefficients.By utilizing the Girsanov theorem,coupling method,trunca...In this paper,we investigate the strong Feller property of stochastic differential equations(SDEs)with super-linear drift and Hölder diffusion coefficients.By utilizing the Girsanov theorem,coupling method,truncation method and the Yamada-Watanabe approximation technique,we derived the strong Feller property of the solution.展开更多
Lithium metal stands out as an exceptionally promising anode material,boasting an extraordinarily high theoretical capacity and impressive energy density.Despite these advantageous characters,the issues of dendrite fo...Lithium metal stands out as an exceptionally promising anode material,boasting an extraordinarily high theoretical capacity and impressive energy density.Despite these advantageous characters,the issues of dendrite formation and volume expansion of lithium metal anodes lead to performance decay and safety concerns,significantly impeding their advancement towards widespread commercial viability.Herein,a lithium-rich Li-B-In composite anode with abundant lithophilic sites and outstanding structural stability is reported to address the mentioned challenges.The evenly distributed Li-In alloy in the bulk phase of anodes act as mixed ion/electron conductors and nucleation sites,facilitating accelerated Li ions transport dynamics and suppressing lithium dendrite formation.Additionally,these micron-sized Li-In particles in LiB fibers framework can enhance overall structural integrity and provide sufficient interior space to accommodate the volume changes during cycling.The electrochemical performance of Li-B-In composite anode exhibits long-term cyclability,superior rate performance and high-capacity retention.This work confirms that the synergy between a 3 D skeleton and hetero-metallic lithiophilic sites can achieve stable and durable lithium metal anodes,offering innovative insights for the practical deployment of lithium metal batteries.展开更多
Comparative studies of four common-used anode gas diffusion layers(A-GDLs),namely carbon cloth,carbon paper,carbon paper based on XC-72(in short XC-72)and GDL made of carbon nanotubes(CNT)for direct methanol fuel cell...Comparative studies of four common-used anode gas diffusion layers(A-GDLs),namely carbon cloth,carbon paper,carbon paper based on XC-72(in short XC-72)and GDL made of carbon nanotubes(CNT)for direct methanol fuel cells(DMFCs)were carried out and discussed.The results of scanning electron microscope(SEM),mercury intrusion porosimeter(MIP)and electrochemical test show that CNT has large pore size distribution in pore size of 1000-3000nm and the largest total porosity compared with those of the other three.Carbon paper and XC-72show disadvantageous influences on cell performances at high current density,because carbon paper has many large pores which are unsuited for water transport,while XC-72has many small pores which are unsuited for gas transport.Though cell with carbon cloth has the highest methanol diffusion coefficient,it shows a little lower performance than that with CNT due to its thickness.Anode polarization(AP)results also display that the cell with CNT has the least methanol mass transfer resistance.As a result,the cell with CNT shows the best performance with the highest limiting current density and peak power density of 460 mA·cm^(-2)and 110mW·cm^(-2),respectively.展开更多
NT build 443, or profile fitting method, is often used to measure the diffusion coefficient of chloride in concrete. However, this method is quite laborious and needs special equipment. Colorimetric method is a quick ...NT build 443, or profile fitting method, is often used to measure the diffusion coefficient of chloride in concrete. However, this method is quite laborious and needs special equipment. Colorimetric method is a quick and simple method to measure the penetration depth of chloride by spraying 0.1 mol/L silver nitrate solution. The objective of this work is to study the possibility of the use of colorimetric method in the calculation of non-steady-state diffusion coefficient. Twelve concrete mixtures with different supplementary cementitious materials and water-to-cement ratios of 0.35, 0.48 and 0.6 were used for study. According to NT build 443, the concrete specimens were immersed in 165 g/L NaC1 （2.8 mol/L） solution for 42 d. Both water-soluble （convert to free chloride） chloride and acid-soluble chloride at different layers of specimens were measured. The results show that the mean value of free chloride concentration at the color change boundary Cd was 0.306 mol/L. The surface free chloride concentration cs was obtained by profile fitting method, which was 40% lower than the chloride concentration of exposure solution after an immersion period of 42 d. Chloride diffusion coefficients obtained by the colorimetric method was not well correlated with those obtained by profile fitting method.展开更多
To denoise the diffusion weighted images （DWls） featured as multi-boundary, which was very important for the calculation of accurate DTIs （diffusion tensor magnetic resonance imaging）, a modified Wiener filter was...To denoise the diffusion weighted images （DWls） featured as multi-boundary, which was very important for the calculation of accurate DTIs （diffusion tensor magnetic resonance imaging）, a modified Wiener filter was proposed. Through analyzing the widely accepted adaptive Wiener filter in image denoising fields, which suffered from annoying noise around the edges of DWIs and in turn greatly affected the denoising effect of DWIs, a local-shift method capable of overcoming the defect of the adaptive Wiener filter was proposed to help better denoising DWIs and the modified Wiener filter was constructed accordingly. To verify the denoising effect of the proposed method, the modified Wiener filter and adaptive Wiener filter were performed on the noisy DWI data, respectively, and the results of different methods were analyzed in detail and put into comparison. The experimental data show that, with the modified Wiener method, more satisfactory results such as lower non-positive tensor percentage and lower mean square errors of the fractional anisotropy map and trace map are obtained than those with the adaptive Wiener method, which in turn helps to produce more accurate DTIs.展开更多
A CFD simulation was carried out to investigate the mixing process in a Y-shape micromixer with the software Fluent 6.3. The definition of the "diffusion angle" is proposed to describe the molecular diffusio...A CFD simulation was carried out to investigate the mixing process in a Y-shape micromixer with the software Fluent 6.3. The definition of the "diffusion angle" is proposed to describe the molecular diffusion process associated with the flow at low Reynolds number. The linear relationship between the diffusion angle and the Peclet number(Pe) is determined by both theoretical analysis and numerical simulation. Moreover, the simulation results reveal that the diffusion angle is only related to the Peclet number whilst it is irrelevant to the changes of Re(Reynolds number) and Sc(Schmidt number). The range of Peclet number and Reynolds number for experimental measurement are also suggested as Pe≤10000 and Re≤10.展开更多
The halide-activated pack cementation process was used to form molybdenum diffusion coating on titanium substrate. The morphology, structure, elements diffusion distribution and microhardness of the coatings formed at...The halide-activated pack cementation process was used to form molybdenum diffusion coating on titanium substrate. The morphology, structure, elements diffusion distribution and microhardness of the coatings formed at different diffusion temperatures were studied. The results indicate that the coating is made up of deposition layer and diffusion layer, and the surface roughness of specimens is increased after diffusion. In the diffusion layer, the major phases are Mo and β-Ti phase with addition of α′-Ti phase and α″-Ti phase. And the phase composition of Mo→β→α″→α′ is formed for different Mo contents in the diffusion layer from outside to inside. The diffusion of Ti element is very obvious as well as Mo element. With increasing the diffusion temperature, the thickness of diffusion layer is increased rapidly, and the microhardness is changed more smoothly with diffusion depth, which shows the same distribution rules as the Mo content.展开更多
The solution diffusion coefficient is a great important intrinsical parameter in crystal growth.On earth,it is impossible to accurately determine the diffusion coefficient since there is nature convection.One of the m...The solution diffusion coefficient is a great important intrinsical parameter in crystal growth.On earth,it is impossible to accurately determine the diffusion coefficient since there is nature convection.One of the marked charateristics of space-crystal growth is to eleminate nature convection,so that purely diffusion-controlled condition of crystal growth could be realized and precise measurement of the diffusion coefficient should be approved.展开更多
The chemical fluid property and the capillary structure of soil are important factors that affect grouting diffusion. Ignoring either factor will produce large errors in understanding the inherent laws of the diffusio...The chemical fluid property and the capillary structure of soil are important factors that affect grouting diffusion. Ignoring either factor will produce large errors in understanding the inherent laws of the diffusion process. Based on fractal geometry and the constitutive equation of Herschel-Bulkley fluid, an analytical model for Herschel-Bulkley fluid flowing in a porous geo-material with fractal characteristics is derived. The proposed model provides a theoretical basis for grouting design and helps to understand the chemical fluid flow in soil in real environments. The results indicate that the predictions from the proposed model show good consistency with the literature data and application results. Grouting pressure decreases with increasing diffusion distance. Under the condition that the chemical fluid flows the same distance, the grouting pressure undergoes almost no change at first and then decreases nonlinearly with increasing tortuosity dimension. With increasing rheological index, the pressure difference first decreases linearly, then presents a trend of nonlinear decrease, and then decreases linearly again. The pressure difference gradually increases with increasing viscosity and yield stress of the chemical fluid. The decreasing trend of the grouting pressure difference is non-linear and rapid for porosity Φ>0.4, while there is a linear and slow decrease in pressure difference for high porosity.展开更多
In the process of sulfuric acid production from pyrite, there is a lot of waste acid produced in fume washing with dilute acid. Acid recovery from this sort of waste sulfuric acid by diffusion dialysis is studied in t...In the process of sulfuric acid production from pyrite, there is a lot of waste acid produced in fume washing with dilute acid. Acid recovery from this sort of waste sulfuric acid by diffusion dialysis is studied in the paper. The mass transfer dialysis coefficient of sulfuric acid of the membrane AFX is measured, the effect of the flowrate of the feed and ratio of feed to water is investigated, and the two kinds of membrane (AFX and S203) are compared. The results show that diffusion dialysis process can separate the metal cation from sulfuric acid effectively, but it is difficult to separate non cation impurities as As - and F -. The contrast tests of the two membranes show that the dialysis mass transfer coefficient of the membrane AFX is larger, while capacity of the removing impurities of membrane S203 is somewhat better.展开更多
To improve the understanding of the transport mechanism in shale gas reservoirs and build a theoretical basic for further researches on productivity evaluation and efficient exploitation, various gas transport mechani...To improve the understanding of the transport mechanism in shale gas reservoirs and build a theoretical basic for further researches on productivity evaluation and efficient exploitation, various gas transport mechanisms within a shale gas reservoir exploited by a horizontal well were thoroughly investigated, which took diffusion, adsorption/desorption and Darcy flow into account. The characteristics of diffusion in nano-scale pores in matrix and desorption on the matrix surface were both considered in the improved differential equations for seepage flow. By integrating the Langmuir isotherm desorption items into the new total dimensionless compression coefficient in matrix, the transport function and seepage flow could be formalized, simplified and consistent with the conventional form of diffusion equation. Furthermore, by utilizing the Laplace change and Sethfest inversion changes, the calculated results were obtained and further discussions indicated that transfer mechanisms were influenced by diffusion, adsorption/desorption. The research shows that when the matrix permeability is closed to magnitude of 10^-9D, the matrix flow only occurs near the surfacial matrix; as to the actual production, the central matrix blocks are barely involved in the production; the closer to the surface of matrix, the lower the pressure is and the more obvious the diffusion effect is; the behavior of adsorption/desorption can increase the matrix flow rate significantly and slow down the pressure of horizontal well obviously.展开更多
Considering both the compaction effect of pile surrounding soil and the stress diffusion effect of pile end soil,this paper theoretically investigates the torsional vibration characteristics of tapered pile.Utilizing ...Considering both the compaction effect of pile surrounding soil and the stress diffusion effect of pile end soil,this paper theoretically investigates the torsional vibration characteristics of tapered pile.Utilizing the complex stiffness transfer model to simulate compaction effect and tapered fictitious soil pile model to simulate stress diffusion,the analytical solution for the torsional impedance at tapered pile top is obtained by virtue of Laplace transform technique and impedance transfer method.Based on the present solution,a parametric study is conducted to investigate the rationality of the present solution and the influence of soil and pile properties on the torsional vibration characteristics of tapered pile embedded in layered soil.The results show that,both the compaction effect and stress diffusion effect have significant influence on the torsional vibration characteristics of tapered pile,and these two factors should be considered during the dynamic design of pile foundation.展开更多
In arid regions, water vapor diffusion predominates the total water migration in unsaturated soil, which significantly influences agriculture and engineering applications. With the aim of revealing the diffusion mecha...In arid regions, water vapor diffusion predominates the total water migration in unsaturated soil, which significantly influences agriculture and engineering applications. With the aim of revealing the diffusion mechanism of water vapor in unsaturated soil, a water vapor migration test device was developed to conduct the water vapor migration indoor test. The test results demonstrate that the characteristics of water vapor diffusion in unsaturated soil conformed to Fick’s second law. A mathematical model for water vapor diffusion under isothermal conditions in unsaturated soil was established based on Fick’s law. Factors including the initial moisture content gradient, initial moisture content distribution, soil type and temperature that affect the water vapor diffusion coefficient were analyzed. The results show that there was good agreement between the moisture content calculated by the mathematical model and obtained by the indoor experiment. The vapor diffusion coefficient increased with increasing initial moisture content gradient and temperature. When the initial moisture content gradient is constant, the vapor diffusion coefficient increases with the increase of matrix suction ratio in dry and wet soil section. The effect of soil type on the water vapor diffusion coefficient was complex, as both the moisture content and soil particle sizes affected the water vapor diffusion.展开更多
基金Project(52174303)supported by the National Natural Science Foundation of ChinaProject(2023JH2/101700302)supported by the Joint Program of Science and Technology Plans in Liaoning Province,China。
文摘Based on microstructure analysis,diffusion theory,and hot deformation experiments,the solidification microstructure and element segregation of the Alloy 625 Plus ingot,the diffusion kinetics of Ti,Nb,and Mo during homogenization and the hot deformation behavior of the homogenized ingot were investigated in this study.The results indicate that:(1)the solidified ingot exhibits a typical dendritic microstructure,and significant element segregation occurs,leading to the presence of Ti,Nb,and Mo-rich precipitates in the interdendritic region;(2)Following homogenization,the degree of element segregation in the ingot is significantly reduced.The diffusion coefficients(D)of Ti,Nb,and Mo under various homogenization conditions were calculated.Subsequently,the diffusion constants(D_(0))and activation energies(Q)of Ti,Nb,and Mo were obtained to be 0.01432,0.00397 and 0.00195 cm^(2)/s and 244.851,230.312,and 222.125 kJ/mol,respectively.Finally,the diffusion kinetics formulas for Ti,Nb,and Mo in Alloy 625 Plus were established.After homogenization at 1220℃for 8 h,the alloy exhibits low deformation resistance,a high degree of recrystallization,and optimal deformation coordination ability.Therefore,this represents a rational single-stage homogenization process.
基金supported by the National Natural Science Foundation of China(Grant No.12372351).
文摘In this study, to meet the development and application requirements for high-strength and hightoughness energetic structural materials, a representative volume element of a TA15 matrix embedded with a TaZrNb sphere was designed and fabricated via diffusion bonding. The mechanisms of the microstructural evolution of the TaZrNb/TA15 interface were investigated via SEM, EBSD, EDS, and XRD.Interface mechanical property tests and in-situ tensile tests were conducted on the sphere-containing structure, and an equivalent tensile-strength model was established for the structure. The results revealed that the TA15 titanium alloy and joint had high density and no pores or cracks. The thickness of the planar joint was approximately 50-60 μm. The average tensile and shear strengths were 767 MPa and 608 MPa, respectively. The thickness of the spherical joint was approximately 60 μm. The Zr and Nb elements in the joint diffused uniformly and formed strong bonds with Ti without forming intermetallic compounds. The interface exhibited submicron grain refinement and a concave-convex interlocking structure. The tensile fracture surface primarily exhibited intergranular fracture combined with some transgranular fracture, which constituted a quasi-brittle fracture mode. The shear fracture surface exhibited brittle fracture with regular arrangements of furrows. Internal fracture occurred along the spherical interface, as revealed by advanced in-situ X-ray microcomputed tomography. The experimental results agreed well with the theoretical predictions, indicating that the high-strength interface contributes to the overall strength and toughness of the sphere-containing structure.
基金Project(2022YFC3801000)supported by the National Key Research and Development Program of ChinaProject(232300421064)supported by the Natural Science Foundation of Henan Province,China+1 种基金Project(241111322700)supported by the Key Research and Development Projects in Henan Province,ChinaProject(52008379)supported by the National Natural Science Foundation of China。
文摘Recently,foamed polymers have been widely used in the repair of underground engineering disasters by grouting(trenchless technology)due to controllable gelation time and self-expansion.However,the grouting process becomes more complicated due to the complex geological conditions and the self-expansion of slurry.Therefore,this paper adopts a self-made visual experimental device with peripheral pressure and water plugging rate(WPR)monitoring functions to study the influence of main influencing parameters(particle size distribution,grouting amount and dynamic water pump pressure(DWPP))on the spatiotemporal distribution of slurry WPR and diffusion dynamic response(peripheral pressure).The results show that:When grouting amount is 563 g and DWPP is 0.013 MPa,the expansion force of the slurry in the diffusion process is dominant and can significantly change the local sand and gravel skeleton structure.When grouting amount is 563 g,DWPP is 0.013 MPa,and particle size distribution type isⅢ,the flow time of the polymer is shortened,the pores of the gravel are rapidly blocked.Then,the peripheral pressure decreases rapidly with the increase of the distance,and the time to reach the inflection point WPR is shortened.The instantaneous blockage of the pores leads to the delayed transmission of flow field blockage information.
基金Project(2022YFB3707201) supported by the National Key R&D Program of ChinaProject(U2341254) supported by the Ye Qisun Science Foundation of National Natural Science Foundation of China+1 种基金Projects(0604022GH0202143,0604022SH0201143) supported by the NPU Aoxiang Distinguished Young Scholars,ChinaProject supported by the Funding of Young Top-notch Talent of the National Ten Thousand Talent Program,China。
文摘Effects of ultrasonic bonding parameters on atomic diffusion, microstructure at the Al-Au interface, and shear strength of Al-Au ultrasonic bonding were investigated by the combining experiments and finite element (FE) simulation. The quantitative model of atomic diffusion, which is related to the ultrasonic bonding parameters, time and distance, is established to calculate the atomic diffusion of the Al-Au interface. The maximum relative error between the calculated and experimental fraction of Al atom is 7.35%, indicating high prediction accuracy of this model. During the process of ultrasonic bonding, Au8Al3 is the main intermetallic compound (IMC) at the Al-Au interface. With larger bonding forces, higher ultrasonic powers and longer bonding time, it is more difficult to remove the oxide particles from the Al-Au interface, which hinders the atomic diffusion. Therefore, the complicated stress state and the existence of oxide particles both promotes the formation of holes. The shear strength of Al-Au ultrasonic bonding increases with increasing bonding force, ultrasonic power and bonding time. However, combined with the presence of holes at especial parameters, the optimal ultrasonic bonding parameter is confirmed to be a bonding force of 23 gf, ultrasonic power of 75 mW and bonding time of 21 ms.
基金Supported by Shanghai Natural Science Foundation(22ZR1472600).
文摘The development of InGaAs/InP single-photon avalanche photodiodes(SPADs)necessitates the utiliza-tion of a two-element diffusion technique to achieve accurate manipulation of the multiplication width and the dis-tribution of its electric field.Regarding the issue of accurately predicting the depth of diffusion in InGaAs/InP SPAD,simulation analysis and device development were carried out,focusing on the dual diffusion behavior of zinc atoms.A formula of X_(j)=k√t-t_(0)+c to quantitatively predict the diffusion depth is obtained by fitting the simulated twice-diffusion depths based on a two-dimensional(2D)model.The 2D impurity morphologies and the one-dimensional impurity profiles for the dual-diffused region are characterized by using scanning electron micros-copy and secondary ion mass spectrometry as a function of the diffusion depth,respectively.InGaAs/InP SPAD devices with different dual-diffusion conditions are also fabricated,which show breakdown behaviors well consis-tent with the simulated results under the same junction geometries.The dark count rate(DCR)of the device de-creased as the multiplication width increased,as indicated by the results.DCRs of 2×10^(6),1×10^(5),4×10^(4),and 2×10^(4) were achieved at temperatures of 300 K,273 K,263 K,and 253 K,respectively,with a bias voltage of 3 V,when the multiplication width was 1.5µm.These results demonstrate an effective prediction route for accu-rately controlling the dual-diffused zinc junction geometry in InP-based planar device processing.
基金Supported by the National Natural Science Foundation of China(11926322)the Fundamental Research Funds for the Central Universities of South-Central MinZu University(CZY22013,3212023sycxjj001)。
文摘In this paper,we investigate the strong Feller property of stochastic differential equations(SDEs)with super-linear drift and Hölder diffusion coefficients.By utilizing the Girsanov theorem,coupling method,truncation method and the Yamada-Watanabe approximation technique,we derived the strong Feller property of the solution.
基金Project(2023YFC3905904)supported by the National Key Research and Development Program,ChinaProject(2220197000221)supported by the Team of Foshan National Hi-Tech Industrial Development Zone Industrialization Entrepreneurial Teams Program,ChinaProject(2024ZZTS0373)supported by the Central South University Graduate Student Autonomous Exploration Innovative Programme,China。
文摘Lithium metal stands out as an exceptionally promising anode material,boasting an extraordinarily high theoretical capacity and impressive energy density.Despite these advantageous characters,the issues of dendrite formation and volume expansion of lithium metal anodes lead to performance decay and safety concerns,significantly impeding their advancement towards widespread commercial viability.Herein,a lithium-rich Li-B-In composite anode with abundant lithophilic sites and outstanding structural stability is reported to address the mentioned challenges.The evenly distributed Li-In alloy in the bulk phase of anodes act as mixed ion/electron conductors and nucleation sites,facilitating accelerated Li ions transport dynamics and suppressing lithium dendrite formation.Additionally,these micron-sized Li-In particles in LiB fibers framework can enhance overall structural integrity and provide sufficient interior space to accommodate the volume changes during cycling.The electrochemical performance of Li-B-In composite anode exhibits long-term cyclability,superior rate performance and high-capacity retention.This work confirms that the synergy between a 3 D skeleton and hetero-metallic lithiophilic sites can achieve stable and durable lithium metal anodes,offering innovative insights for the practical deployment of lithium metal batteries.
文摘Comparative studies of four common-used anode gas diffusion layers(A-GDLs),namely carbon cloth,carbon paper,carbon paper based on XC-72(in short XC-72)and GDL made of carbon nanotubes(CNT)for direct methanol fuel cells(DMFCs)were carried out and discussed.The results of scanning electron microscope(SEM),mercury intrusion porosimeter(MIP)and electrochemical test show that CNT has large pore size distribution in pore size of 1000-3000nm and the largest total porosity compared with those of the other three.Carbon paper and XC-72show disadvantageous influences on cell performances at high current density,because carbon paper has many large pores which are unsuited for water transport,while XC-72has many small pores which are unsuited for gas transport.Though cell with carbon cloth has the highest methanol diffusion coefficient,it shows a little lower performance than that with CNT due to its thickness.Anode polarization(AP)results also display that the cell with CNT has the least methanol mass transfer resistance.As a result,the cell with CNT shows the best performance with the highest limiting current density and peak power density of 460 mA·cm^(-2)and 110mW·cm^(-2),respectively.
基金Project(2010QZZD018) supported by Central South Universtiy,China,and Ghent University,Belgium
文摘NT build 443, or profile fitting method, is often used to measure the diffusion coefficient of chloride in concrete. However, this method is quite laborious and needs special equipment. Colorimetric method is a quick and simple method to measure the penetration depth of chloride by spraying 0.1 mol/L silver nitrate solution. The objective of this work is to study the possibility of the use of colorimetric method in the calculation of non-steady-state diffusion coefficient. Twelve concrete mixtures with different supplementary cementitious materials and water-to-cement ratios of 0.35, 0.48 and 0.6 were used for study. According to NT build 443, the concrete specimens were immersed in 165 g/L NaC1 （2.8 mol/L） solution for 42 d. Both water-soluble （convert to free chloride） chloride and acid-soluble chloride at different layers of specimens were measured. The results show that the mean value of free chloride concentration at the color change boundary Cd was 0.306 mol/L. The surface free chloride concentration cs was obtained by profile fitting method, which was 40% lower than the chloride concentration of exposure solution after an immersion period of 42 d. Chloride diffusion coefficients obtained by the colorimetric method was not well correlated with those obtained by profile fitting method.
基金Project(2009AA04Z214) supported by the National High Technology Research and Development Program of ChinaProject(07JJ6133) supported by the Natural Science Foundation of Hunan Province, China
文摘To denoise the diffusion weighted images （DWls） featured as multi-boundary, which was very important for the calculation of accurate DTIs （diffusion tensor magnetic resonance imaging）, a modified Wiener filter was proposed. Through analyzing the widely accepted adaptive Wiener filter in image denoising fields, which suffered from annoying noise around the edges of DWIs and in turn greatly affected the denoising effect of DWIs, a local-shift method capable of overcoming the defect of the adaptive Wiener filter was proposed to help better denoising DWIs and the modified Wiener filter was constructed accordingly. To verify the denoising effect of the proposed method, the modified Wiener filter and adaptive Wiener filter were performed on the noisy DWI data, respectively, and the results of different methods were analyzed in detail and put into comparison. The experimental data show that, with the modified Wiener method, more satisfactory results such as lower non-positive tensor percentage and lower mean square errors of the fractional anisotropy map and trace map are obtained than those with the adaptive Wiener method, which in turn helps to produce more accurate DTIs.
基金Project(51106184)supported by the National Natural Science Foundation of China
文摘A CFD simulation was carried out to investigate the mixing process in a Y-shape micromixer with the software Fluent 6.3. The definition of the "diffusion angle" is proposed to describe the molecular diffusion process associated with the flow at low Reynolds number. The linear relationship between the diffusion angle and the Peclet number(Pe) is determined by both theoretical analysis and numerical simulation. Moreover, the simulation results reveal that the diffusion angle is only related to the Peclet number whilst it is irrelevant to the changes of Re(Reynolds number) and Sc(Schmidt number). The range of Peclet number and Reynolds number for experimental measurement are also suggested as Pe≤10000 and Re≤10.
文摘The halide-activated pack cementation process was used to form molybdenum diffusion coating on titanium substrate. The morphology, structure, elements diffusion distribution and microhardness of the coatings formed at different diffusion temperatures were studied. The results indicate that the coating is made up of deposition layer and diffusion layer, and the surface roughness of specimens is increased after diffusion. In the diffusion layer, the major phases are Mo and β-Ti phase with addition of α′-Ti phase and α″-Ti phase. And the phase composition of Mo→β→α″→α′ is formed for different Mo contents in the diffusion layer from outside to inside. The diffusion of Ti element is very obvious as well as Mo element. With increasing the diffusion temperature, the thickness of diffusion layer is increased rapidly, and the microhardness is changed more smoothly with diffusion depth, which shows the same distribution rules as the Mo content.
文摘The solution diffusion coefficient is a great important intrinsical parameter in crystal growth.On earth,it is impossible to accurately determine the diffusion coefficient since there is nature convection.One of the marked charateristics of space-crystal growth is to eleminate nature convection,so that purely diffusion-controlled condition of crystal growth could be realized and precise measurement of the diffusion coefficient should be approved.
基金Project(2015CB060200)supported by the National Basic Research Program of ChinaProject supported by the R-D Program of Gangxi Province of ChinaProject(201622ts093)supported by the Fundamental Research Funds for the Central Universities,China
文摘The chemical fluid property and the capillary structure of soil are important factors that affect grouting diffusion. Ignoring either factor will produce large errors in understanding the inherent laws of the diffusion process. Based on fractal geometry and the constitutive equation of Herschel-Bulkley fluid, an analytical model for Herschel-Bulkley fluid flowing in a porous geo-material with fractal characteristics is derived. The proposed model provides a theoretical basis for grouting design and helps to understand the chemical fluid flow in soil in real environments. The results indicate that the predictions from the proposed model show good consistency with the literature data and application results. Grouting pressure decreases with increasing diffusion distance. Under the condition that the chemical fluid flows the same distance, the grouting pressure undergoes almost no change at first and then decreases nonlinearly with increasing tortuosity dimension. With increasing rheological index, the pressure difference first decreases linearly, then presents a trend of nonlinear decrease, and then decreases linearly again. The pressure difference gradually increases with increasing viscosity and yield stress of the chemical fluid. The decreasing trend of the grouting pressure difference is non-linear and rapid for porosity Φ>0.4, while there is a linear and slow decrease in pressure difference for high porosity.
文摘In the process of sulfuric acid production from pyrite, there is a lot of waste acid produced in fume washing with dilute acid. Acid recovery from this sort of waste sulfuric acid by diffusion dialysis is studied in the paper. The mass transfer dialysis coefficient of sulfuric acid of the membrane AFX is measured, the effect of the flowrate of the feed and ratio of feed to water is investigated, and the two kinds of membrane (AFX and S203) are compared. The results show that diffusion dialysis process can separate the metal cation from sulfuric acid effectively, but it is difficult to separate non cation impurities as As - and F -. The contrast tests of the two membranes show that the dialysis mass transfer coefficient of the membrane AFX is larger, while capacity of the removing impurities of membrane S203 is somewhat better.
基金Foundation item： Project（PLN1129）supported by Opening Fund of State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation （Southwest Petroleum University）, China
文摘To improve the understanding of the transport mechanism in shale gas reservoirs and build a theoretical basic for further researches on productivity evaluation and efficient exploitation, various gas transport mechanisms within a shale gas reservoir exploited by a horizontal well were thoroughly investigated, which took diffusion, adsorption/desorption and Darcy flow into account. The characteristics of diffusion in nano-scale pores in matrix and desorption on the matrix surface were both considered in the improved differential equations for seepage flow. By integrating the Langmuir isotherm desorption items into the new total dimensionless compression coefficient in matrix, the transport function and seepage flow could be formalized, simplified and consistent with the conventional form of diffusion equation. Furthermore, by utilizing the Laplace change and Sethfest inversion changes, the calculated results were obtained and further discussions indicated that transfer mechanisms were influenced by diffusion, adsorption/desorption. The research shows that when the matrix permeability is closed to magnitude of 10^-9D, the matrix flow only occurs near the surfacial matrix; as to the actual production, the central matrix blocks are barely involved in the production; the closer to the surface of matrix, the lower the pressure is and the more obvious the diffusion effect is; the behavior of adsorption/desorption can increase the matrix flow rate significantly and slow down the pressure of horizontal well obviously.
基金Projects(51578164,51678547,51878634,51878185,41807262)supported by the National Natural Science Foundation of China。
文摘Considering both the compaction effect of pile surrounding soil and the stress diffusion effect of pile end soil,this paper theoretically investigates the torsional vibration characteristics of tapered pile.Utilizing the complex stiffness transfer model to simulate compaction effect and tapered fictitious soil pile model to simulate stress diffusion,the analytical solution for the torsional impedance at tapered pile top is obtained by virtue of Laplace transform technique and impedance transfer method.Based on the present solution,a parametric study is conducted to investigate the rationality of the present solution and the influence of soil and pile properties on the torsional vibration characteristics of tapered pile embedded in layered soil.The results show that,both the compaction effect and stress diffusion effect have significant influence on the torsional vibration characteristics of tapered pile,and these two factors should be considered during the dynamic design of pile foundation.
基金Projects(51878064, 51378072) supported by the National Natural Science Foundation of ChinaProjects(300102218408, 300102219108) supported by the Fundamental Research Funds for the Central Universities, China。
文摘In arid regions, water vapor diffusion predominates the total water migration in unsaturated soil, which significantly influences agriculture and engineering applications. With the aim of revealing the diffusion mechanism of water vapor in unsaturated soil, a water vapor migration test device was developed to conduct the water vapor migration indoor test. The test results demonstrate that the characteristics of water vapor diffusion in unsaturated soil conformed to Fick’s second law. A mathematical model for water vapor diffusion under isothermal conditions in unsaturated soil was established based on Fick’s law. Factors including the initial moisture content gradient, initial moisture content distribution, soil type and temperature that affect the water vapor diffusion coefficient were analyzed. The results show that there was good agreement between the moisture content calculated by the mathematical model and obtained by the indoor experiment. The vapor diffusion coefficient increased with increasing initial moisture content gradient and temperature. When the initial moisture content gradient is constant, the vapor diffusion coefficient increases with the increase of matrix suction ratio in dry and wet soil section. The effect of soil type on the water vapor diffusion coefficient was complex, as both the moisture content and soil particle sizes affected the water vapor diffusion.
