A comprehensive thermodynamic model, which combined the Helgeson Kirkham-Flowers （HKF） equation of state for standard-state thermodynamic properties of all species with realistic activity coefficient model developed...A comprehensive thermodynamic model, which combined the Helgeson Kirkham-Flowers （HKF） equation of state for standard-state thermodynamic properties of all species with realistic activity coefficient model developed by BROMLEY, was used to calculate the thermodynamic equilibrium, and a graphical method was developed to construct predominance existence diagrams （PED） for copper-ammonia-chloride in the presence of realistically modeled aqueous solutions. The existence of the different predominant chemical species for Cu（lI） predicted by the diagrams was corroborated by spectrophotometrical studies and X-ray diffractometry. The simulated and experimental results indicate that the predominance of a given species in solution strongly depends on the pH value in this system. More quantitative information on real copper hydrometallurgy in the presence of ammonia and chloride can be obtained from these diagrams compared with the conventional predominance existence diagrams.展开更多
Aqueous E pH Diagram is an essential tool for analyzing hydrometallurgical and corrosion processes. Due to the requirements for environmental protection and energy saving in recent years, waste water processing a...Aqueous E pH Diagram is an essential tool for analyzing hydrometallurgical and corrosion processes. Due to the requirements for environmental protection and energy saving in recent years, waste water processing and hydrometallurgical process of concentrate have been greatly developed. The construction of E pH diagrams has turned to multi component systems. However, there are some limits in plotting such diagrams. There is only one diagram for one multi component system, which can not reflect the truth of the aqueous reaction. In the paper, a new computation method is proposed to construct E pH diagrams. Component activity term is used to determine the boundary of stable areas. For the multi component systems, different atom ratios of elements have been taken into account. M S H 2O system is chosen to study since it is of importance in metallurgical solution. Compared with conventional methods, the algorithm is simple and conforms to real conditions.展开更多
System of systems architecture（SoSA） has received increasing emphasis by scholars since Zachman ignited its flame in 1987. Given its complexity and abstractness, it is critical to validate and evaluate SoSA to ensur...System of systems architecture（SoSA） has received increasing emphasis by scholars since Zachman ignited its flame in 1987. Given its complexity and abstractness, it is critical to validate and evaluate SoSA to ensure requirements have been met.Multiple qualities are discussed in the literature of SoSA evaluation, while research on functionality is scarce. In order to assess SoSA functionality, an extended influence diagram（EID） is developed in this paper. Meanwhile, a simulation method is proposed to elicit the conditional probabilities in EID through designing and executing SoSA. An illustrative anti-missile architecture case is introduced for EID development, architecture design, and simulation.展开更多
[Objective]The work is devoted to the study of irreversible deformation of artificial samples subjected to a set of standard experiments,with an aim to study their mechanical properties.The principal idea of the study...[Objective]The work is devoted to the study of irreversible deformation of artificial samples subjected to a set of standard experiments,with an aim to study their mechanical properties.The principal idea of the study is related to the preparation of an artificial material with an established constitutive behavior model.The existence of such a well-described material provides future opportunities to conduct controllable experiments on various mechanical processes in rock-like material for further development and validation of theoretical models used in rock mechanics.[Methods]A set of artificial samples was prepared for careful assessment through a number of loading tests.Experimental work was carried out to determine the rheological properties under conditions of triaxial compression tests and uniaxial tension.Triaxial loading tests are completed for 9 samples with varying radial stress levels(0-5 MPa).The samples are loaded up to the yield point with control of radial and volumetric strain.The experimental results,which contain the obtained interrelationships between axial and radial stresses and strains,are analyzed using the Drucker-Prager yield surface.Material hardening is taken into account through the non-associated plastic flow law with the cap model.Numerical modeling of sample loading is performed through the finite difference method.Mathematical model parameters are adjusted to minimize the discrepancy between numerical modeling results and experimental data.The design of a series of experimental studies necessary to determine all the parameters of the model has been studied.[Results]It is shown that the formulated mathematical model allows to reliably reproduce the inelastic behavior of the studied material,and it can be used to solve a set of applied problems in continuum mechanics,the problem of numerical simulation of hydraulic fracture growth in an elastoplastic medium in particular.It was found that for the entire range of applied lateral loads(0-5 MPa),the elastic limit varied from 2 to 4 MPa,after which the material began to behave plastically.It was also determined that at lateral loads≥3 MPa,compaction began to appear in the material beyond the yield point.Judging by the dependence of volumetric strains under a lateral load equal to 1.4 MPa,compaction should begin to appear even at lateral loads lower than 3 MPa.[Conclusion]Taking the plastic behavior of the material into account is necessary when moving on to modeling the hydraulic fracturing process in such a material,and the resultant plasticity parameters for the model material can be used for numerical modeling of elastoplastic deformation of the rock under consideration,including processes such as hydraulic fracture growth in a poroelastoplastic medium.[Significance]The suggested procedure to interpret results of experimental studies can be used for further numerical modeling of mechanical processes in rock masses with inelastic strain accumulation.This opportunity can increase the reliability of geomechanical models used for the optimization of hydrocarbon fields development.展开更多
Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material stru...Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material structure simulation has become more and more perfect.This study employs numerical simulation to investigate the microstructure evolution of Al-Cu-Mg-Ag alloys during solidification with the aim of controlling its structure.The size distribution of Ti-containing particles in an Al-Ti-B master alloy was characterized via microstructure observation,serving as a basis for optimizing the nucleation density parameters for particles of varying radii in the phase field model.The addition of refiner inhibited the growth of dendrites and no longer produced coarse dendrites.With the increase of refiner,the grains gradually tended to form cellular morphology.The refined grains were about 100μm in size.Experimental validation of the simulated as-cast grain morphology was conducted.The samples were observed by metallographic microscope and scanning electron microscope.The addition of refiner had a significant effect on the refinement of the alloy,and the average grain size after refinement was also about 100μm.At the same time,the XRD phase identification of the alloy was carried out.The observation of the microstructure morphology under the scanning electron microscope showed that the precipitated phase was mainly concentrated on the grain boundary.The Al_(2)Cu accounted for about 5%,and the matrix phase FCC accounted for about 95%,which also corresponded well with the simulation results.展开更多
This paper proposes a reliability evaluation model for a multi-dimensional network system,which has potential to be applied to the internet of things or other practical networks.A multi-dimensional network system with...This paper proposes a reliability evaluation model for a multi-dimensional network system,which has potential to be applied to the internet of things or other practical networks.A multi-dimensional network system with one source element and multiple sink elements is considered first.Each element can con-nect with other elements within a stochastic connection ranges.The system is regarded as successful as long as the source ele-ment remains connected with all sink elements.An importance measure is proposed to evaluate the performance of non-source elements.Furthermore,to calculate the system reliability and the element importance measure,a multi-valued decision diagram based approach is structured and its complexity is analyzed.Finally,a numerical example about the signal transfer station system is illustrated to analyze the system reliability and the ele-ment importance measure.展开更多
The article deals with the motion of the breech block carrier and the weapon casing of an automatic weapon mounted on a flexible carriage and the base of the weapon.Earlier works,which did not consider the dynamic pro...The article deals with the motion of the breech block carrier and the weapon casing of an automatic weapon mounted on a flexible carriage and the base of the weapon.Earlier works,which did not consider the dynamic properties of the base of the weapon,did not allow to reconcile the calculated and experimental results of the weapon casing displacement when shooting from firing rests.For the analysis of the motion of individual parts,the methods of mathematical modelling and firing experiments using a high-speed camera were chosen.Calculations show the best accord with experiment when modelling the system with 4 degrees of freedom.The oscillation of the system regarding the movement of the breech block carrier and the weapon casing was investigated under changed conditions of rate of fire,the use of a muzzle brake and different types of shock absorbers.The velocities and displacements of the weapon casing and the breech block carrier at different values of the impulse of the gases to the breech block carrier were determined.展开更多
以立方结构的纯金属为研究对象,在文献报道的实验信息的基础上,运用改进的半经验模型优化并计算了金属在不同温度时的杨氏模量.借鉴相图计算的CALPHAD(calculation of phase diagrams)方法,构建了二元合金杨氏模量计算的新模型.基于二...以立方结构的纯金属为研究对象,在文献报道的实验信息的基础上,运用改进的半经验模型优化并计算了金属在不同温度时的杨氏模量.借鉴相图计算的CALPHAD(calculation of phase diagrams)方法,构建了二元合金杨氏模量计算的新模型.基于二元合金的实验信息,对Ag-Au、Ta-W、Pt-Rh和Pt-Ir 4个二元合金的杨氏模量计算参数进行了优化,计算了合金在不同温度、成分时的杨氏模量,计算结果与实验信息取得了良好的一致性.展开更多
Lower Silurian Longmaxi Shale(SLS) in southeastern Sichuan Basin, China, was analyzed for major and selected trace elements, and their provenance, intensity of palaeoweathering of the source rocks were analyzed based ...Lower Silurian Longmaxi Shale(SLS) in southeastern Sichuan Basin, China, was analyzed for major and selected trace elements, and their provenance, intensity of palaeoweathering of the source rocks were analyzed based on these elements. The results show that SiO_2, Al_2O_3 and Fe_2O_3, are dominant major elements with average contents of 60.59%, 15.91% and 5.87% in Upper Silurian Longmaxi Shale(USLS), and 65.14%, 13.24% and 4.68% in Lower Silurian Longmaxi Shale(LSLS). The TiO_2-Zr plot, Hf(ppm) versus La/Th discriminant diagram, and abundance of Cr and Ni suggest a dominantly felsic source for the Longmaxi sediments. Average chemical index of alteration(CIA), plagioclase index of alteration(PIA) values(64.05% and 72.86%, respectively) imply low-degree chemical weathering of the source material in early Longmaxi time, and average CIA, PIA values(68.44% and 80.35%, respectively) imply moderate chemical weathering of the source material in late Longmaxi time.展开更多
The constructed potential-pH diagrams of Li-Ni(Co,Mn)-H_(2)O system indicate that the LiNiO_(2),LiCoO_(2)and LiMnO_(2)are thermodynamically stable in aqueous solution within the temperature range of 25-200℃and the ac...The constructed potential-pH diagrams of Li-Ni(Co,Mn)-H_(2)O system indicate that the LiNiO_(2),LiCoO_(2)and LiMnO_(2)are thermodynamically stable in aqueous solution within the temperature range of 25-200℃and the activity range of 0.01-1.00.A predominant co-region of LiNiO_(2),LiCoO_(2)and LiMnO_(2)oxides(Li-Ni-Co-Mncomposite oxide)is found in the Li-Ni-Co-Mn-H_(2)O potential-pH diagrams,in which the co-precipitation region expands towards lower pH with rising temperature,indicating the enhanced possibility of synthesizing Li-Ni-Co-Mn composite oxide in aqueous solution.The experimental results prove that it is feasible to prepare the LiNi_(0.5)Co_(0.2)Mn_(0.3)O_(2)cathode materials(NCM523)by an aqueous routine.The as-prepared lithiated precursor and NCM523 both inherit the spherical morphology of the hydroxide precursor and the obtained NCM523 has a hexagonalα-NaFeO_(2)structure with good crystallinity.It is reasonable to conclude that the aqueous routine for preparing NCM cathode materials is a promising method with the guidance of the reliable potential-pH diagrams to some extent.展开更多
From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the A...From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the AUTOCAD model into 3DEC (3-dimensional distinct element code) model was developed, and a numerical model was established in 3DEC. Moreover, the results of triaxial compression tests of columnar jointed rock masses were simulated numerically. The REV (representative element volume) scale was studied, and the result shows that the REV size is 3 m × 3 m. The proposed approach, the established model and the numerical simulation were applied to study the macro-mechanical properties and the equivalent strength parameters of the columnar jointed rock mass. The numerical simulation results are in good accordance with the in-situ test results.展开更多
A multi-stage influence diagram is used to model the pilot＇s sequential decision making in one on one air combat. The model based on the multi-stage influence diagram graphically describes the elements of decision pr...A multi-stage influence diagram is used to model the pilot＇s sequential decision making in one on one air combat. The model based on the multi-stage influence diagram graphically describes the elements of decision process, and contains a point-mass model for the dynamics of an aircraft and takes into account the decision maker＇s preferences under uncertain conditions. Considering an active opponent, the opponent＇s maneuvers can be modeled stochastically. The solution of multistage influence diagram can be obtained by converting the multistage influence diagram into a two-level optimization problem. The simulation results show the model is effective.展开更多
Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that ...Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that the SDOF systems are accurate in predicting the failure mode of the slab under blast loads by incorporating the effects of the strain rate effect caused by rapid load application. Based on different damage criteria, pressure-impulse (P-I) diagrams of the two failure modes were analyzed with the SDOF systems. The effects of span length, concrete strength, and reinforcement ratio of the slab on the P-I diagram were also investigated. Results indicate that a slab tends to fail in direct shear mode when it is of a smaller span length and tends to fail in flexure mode when it is of a larger span length. With the increase of the concrete strength or reinforced ratio, both the flexure and shear capacity increase. Based on numerical results, a simplified method and a semi analytical equation for deriving the P-I diagram are proposed for different failure modes and damage levels.展开更多
基金Project(2007CB613601) supported by the National Basic Research Program of China
文摘A comprehensive thermodynamic model, which combined the Helgeson Kirkham-Flowers （HKF） equation of state for standard-state thermodynamic properties of all species with realistic activity coefficient model developed by BROMLEY, was used to calculate the thermodynamic equilibrium, and a graphical method was developed to construct predominance existence diagrams （PED） for copper-ammonia-chloride in the presence of realistically modeled aqueous solutions. The existence of the different predominant chemical species for Cu（lI） predicted by the diagrams was corroborated by spectrophotometrical studies and X-ray diffractometry. The simulated and experimental results indicate that the predominance of a given species in solution strongly depends on the pH value in this system. More quantitative information on real copper hydrometallurgy in the presence of ammonia and chloride can be obtained from these diagrams compared with the conventional predominance existence diagrams.
文摘Aqueous E pH Diagram is an essential tool for analyzing hydrometallurgical and corrosion processes. Due to the requirements for environmental protection and energy saving in recent years, waste water processing and hydrometallurgical process of concentrate have been greatly developed. The construction of E pH diagrams has turned to multi component systems. However, there are some limits in plotting such diagrams. There is only one diagram for one multi component system, which can not reflect the truth of the aqueous reaction. In the paper, a new computation method is proposed to construct E pH diagrams. Component activity term is used to determine the boundary of stable areas. For the multi component systems, different atom ratios of elements have been taken into account. M S H 2O system is chosen to study since it is of importance in metallurgical solution. Compared with conventional methods, the algorithm is simple and conforms to real conditions.
基金supported by the National Natural Science Foundation of China(71571189)
文摘System of systems architecture（SoSA） has received increasing emphasis by scholars since Zachman ignited its flame in 1987. Given its complexity and abstractness, it is critical to validate and evaluate SoSA to ensure requirements have been met.Multiple qualities are discussed in the literature of SoSA evaluation, while research on functionality is scarce. In order to assess SoSA functionality, an extended influence diagram（EID） is developed in this paper. Meanwhile, a simulation method is proposed to elicit the conditional probabilities in EID through designing and executing SoSA. An illustrative anti-missile architecture case is introduced for EID development, architecture design, and simulation.
文摘[Objective]The work is devoted to the study of irreversible deformation of artificial samples subjected to a set of standard experiments,with an aim to study their mechanical properties.The principal idea of the study is related to the preparation of an artificial material with an established constitutive behavior model.The existence of such a well-described material provides future opportunities to conduct controllable experiments on various mechanical processes in rock-like material for further development and validation of theoretical models used in rock mechanics.[Methods]A set of artificial samples was prepared for careful assessment through a number of loading tests.Experimental work was carried out to determine the rheological properties under conditions of triaxial compression tests and uniaxial tension.Triaxial loading tests are completed for 9 samples with varying radial stress levels(0-5 MPa).The samples are loaded up to the yield point with control of radial and volumetric strain.The experimental results,which contain the obtained interrelationships between axial and radial stresses and strains,are analyzed using the Drucker-Prager yield surface.Material hardening is taken into account through the non-associated plastic flow law with the cap model.Numerical modeling of sample loading is performed through the finite difference method.Mathematical model parameters are adjusted to minimize the discrepancy between numerical modeling results and experimental data.The design of a series of experimental studies necessary to determine all the parameters of the model has been studied.[Results]It is shown that the formulated mathematical model allows to reliably reproduce the inelastic behavior of the studied material,and it can be used to solve a set of applied problems in continuum mechanics,the problem of numerical simulation of hydraulic fracture growth in an elastoplastic medium in particular.It was found that for the entire range of applied lateral loads(0-5 MPa),the elastic limit varied from 2 to 4 MPa,after which the material began to behave plastically.It was also determined that at lateral loads≥3 MPa,compaction began to appear in the material beyond the yield point.Judging by the dependence of volumetric strains under a lateral load equal to 1.4 MPa,compaction should begin to appear even at lateral loads lower than 3 MPa.[Conclusion]Taking the plastic behavior of the material into account is necessary when moving on to modeling the hydraulic fracturing process in such a material,and the resultant plasticity parameters for the model material can be used for numerical modeling of elastoplastic deformation of the rock under consideration,including processes such as hydraulic fracture growth in a poroelastoplastic medium.[Significance]The suggested procedure to interpret results of experimental studies can be used for further numerical modeling of mechanical processes in rock masses with inelastic strain accumulation.This opportunity can increase the reliability of geomechanical models used for the optimization of hydrocarbon fields development.
文摘Al-Cu-Mg-Ag alloys have become a research hotspot because of its good heat resistance.Its excellent mechanical properties are inseparable from the regulation of the structure by researchers.The method of material structure simulation has become more and more perfect.This study employs numerical simulation to investigate the microstructure evolution of Al-Cu-Mg-Ag alloys during solidification with the aim of controlling its structure.The size distribution of Ti-containing particles in an Al-Ti-B master alloy was characterized via microstructure observation,serving as a basis for optimizing the nucleation density parameters for particles of varying radii in the phase field model.The addition of refiner inhibited the growth of dendrites and no longer produced coarse dendrites.With the increase of refiner,the grains gradually tended to form cellular morphology.The refined grains were about 100μm in size.Experimental validation of the simulated as-cast grain morphology was conducted.The samples were observed by metallographic microscope and scanning electron microscope.The addition of refiner had a significant effect on the refinement of the alloy,and the average grain size after refinement was also about 100μm.At the same time,the XRD phase identification of the alloy was carried out.The observation of the microstructure morphology under the scanning electron microscope showed that the precipitated phase was mainly concentrated on the grain boundary.The Al_(2)Cu accounted for about 5%,and the matrix phase FCC accounted for about 95%,which also corresponded well with the simulation results.
基金supported by the National Natural Science Foundation of China(72101025,72271049),the Interdisciplinary Research Project for Young Teachers of USTB(Fundamental Research Funds for the Central Universities,FRF-IDRY-24-024)the Hebei Natural Science Foundation(F2023501011)+1 种基金the Fundamental Research Funds for the Central Universities(FRF-TP-20-073A1)the R&D Program of Beijing Municipal Education Commission(KM202411232015).
文摘This paper proposes a reliability evaluation model for a multi-dimensional network system,which has potential to be applied to the internet of things or other practical networks.A multi-dimensional network system with one source element and multiple sink elements is considered first.Each element can con-nect with other elements within a stochastic connection ranges.The system is regarded as successful as long as the source ele-ment remains connected with all sink elements.An importance measure is proposed to evaluate the performance of non-source elements.Furthermore,to calculate the system reliability and the element importance measure,a multi-valued decision diagram based approach is structured and its complexity is analyzed.Finally,a numerical example about the signal transfer station system is illustrated to analyze the system reliability and the ele-ment importance measure.
基金supported by the Research project VAROPS(Military autonomous and robotic assets)of the Ministry of Defence of The Czech Republicby the Specific Research Support Project(Grant No.SV22-201)financed from funds of the Ministry of Education,Youth and Sports of The Czech Republic。
文摘The article deals with the motion of the breech block carrier and the weapon casing of an automatic weapon mounted on a flexible carriage and the base of the weapon.Earlier works,which did not consider the dynamic properties of the base of the weapon,did not allow to reconcile the calculated and experimental results of the weapon casing displacement when shooting from firing rests.For the analysis of the motion of individual parts,the methods of mathematical modelling and firing experiments using a high-speed camera were chosen.Calculations show the best accord with experiment when modelling the system with 4 degrees of freedom.The oscillation of the system regarding the movement of the breech block carrier and the weapon casing was investigated under changed conditions of rate of fire,the use of a muzzle brake and different types of shock absorbers.The velocities and displacements of the weapon casing and the breech block carrier at different values of the impulse of the gases to the breech block carrier were determined.
文摘以立方结构的纯金属为研究对象,在文献报道的实验信息的基础上,运用改进的半经验模型优化并计算了金属在不同温度时的杨氏模量.借鉴相图计算的CALPHAD(calculation of phase diagrams)方法,构建了二元合金杨氏模量计算的新模型.基于二元合金的实验信息,对Ag-Au、Ta-W、Pt-Rh和Pt-Ir 4个二元合金的杨氏模量计算参数进行了优化,计算了合金在不同温度、成分时的杨氏模量,计算结果与实验信息取得了良好的一致性.
基金Project(41302076)supported by the National Natural Science Foundation of ChinaProject(BJ14266)supported by MOST Special Fund from the State Key Laboratory of Continental Dynamics,Northwest University,ChinaProject(2014JQ5191)supported by Natural Science Basic Research Plan of Shaanxi Province,China
文摘Lower Silurian Longmaxi Shale(SLS) in southeastern Sichuan Basin, China, was analyzed for major and selected trace elements, and their provenance, intensity of palaeoweathering of the source rocks were analyzed based on these elements. The results show that SiO_2, Al_2O_3 and Fe_2O_3, are dominant major elements with average contents of 60.59%, 15.91% and 5.87% in Upper Silurian Longmaxi Shale(USLS), and 65.14%, 13.24% and 4.68% in Lower Silurian Longmaxi Shale(LSLS). The TiO_2-Zr plot, Hf(ppm) versus La/Th discriminant diagram, and abundance of Cr and Ni suggest a dominantly felsic source for the Longmaxi sediments. Average chemical index of alteration(CIA), plagioclase index of alteration(PIA) values(64.05% and 72.86%, respectively) imply low-degree chemical weathering of the source material in early Longmaxi time, and average CIA, PIA values(68.44% and 80.35%, respectively) imply moderate chemical weathering of the source material in late Longmaxi time.
基金Project(FA2019015)supported by the Government of Chongzuo,Guangxi Zhuang Autonomous Region,ChinaProject(AD18281073)supported by Science and Technology Department of Guangxi Zhuang Autonomous Region,China
文摘The constructed potential-pH diagrams of Li-Ni(Co,Mn)-H_(2)O system indicate that the LiNiO_(2),LiCoO_(2)and LiMnO_(2)are thermodynamically stable in aqueous solution within the temperature range of 25-200℃and the activity range of 0.01-1.00.A predominant co-region of LiNiO_(2),LiCoO_(2)and LiMnO_(2)oxides(Li-Ni-Co-Mncomposite oxide)is found in the Li-Ni-Co-Mn-H_(2)O potential-pH diagrams,in which the co-precipitation region expands towards lower pH with rising temperature,indicating the enhanced possibility of synthesizing Li-Ni-Co-Mn composite oxide in aqueous solution.The experimental results prove that it is feasible to prepare the LiNi_(0.5)Co_(0.2)Mn_(0.3)O_(2)cathode materials(NCM523)by an aqueous routine.The as-prepared lithiated precursor and NCM523 both inherit the spherical morphology of the hydroxide precursor and the obtained NCM523 has a hexagonalα-NaFeO_(2)structure with good crystallinity.It is reasonable to conclude that the aqueous routine for preparing NCM cathode materials is a promising method with the guidance of the reliable potential-pH diagrams to some extent.
基金Projects(50911130366, 50979030) supported by the National Natural Science Foundation of China
文摘From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the AUTOCAD model into 3DEC (3-dimensional distinct element code) model was developed, and a numerical model was established in 3DEC. Moreover, the results of triaxial compression tests of columnar jointed rock masses were simulated numerically. The REV (representative element volume) scale was studied, and the result shows that the REV size is 3 m × 3 m. The proposed approach, the established model and the numerical simulation were applied to study the macro-mechanical properties and the equivalent strength parameters of the columnar jointed rock mass. The numerical simulation results are in good accordance with the in-situ test results.
文摘A multi-stage influence diagram is used to model the pilot＇s sequential decision making in one on one air combat. The model based on the multi-stage influence diagram graphically describes the elements of decision process, and contains a point-mass model for the dynamics of an aircraft and takes into account the decision maker＇s preferences under uncertain conditions. Considering an active opponent, the opponent＇s maneuvers can be modeled stochastically. The solution of multistage influence diagram can be obtained by converting the multistage influence diagram into a two-level optimization problem. The simulation results show the model is effective.
基金Project(JC11-02-18) supported by the Scientific Foundation of National University of Defense Technology, ChinaProject(11202236) supported by the National Natural Science Foundation of China
文摘Two loosely coupled single degree of freedom (SDOF) systems were used to model the flexural and direct shear responses of one-way reinforced concrete slabs subjected to explosive loading. Blast test results show that the SDOF systems are accurate in predicting the failure mode of the slab under blast loads by incorporating the effects of the strain rate effect caused by rapid load application. Based on different damage criteria, pressure-impulse (P-I) diagrams of the two failure modes were analyzed with the SDOF systems. The effects of span length, concrete strength, and reinforcement ratio of the slab on the P-I diagram were also investigated. Results indicate that a slab tends to fail in direct shear mode when it is of a smaller span length and tends to fail in flexure mode when it is of a larger span length. With the increase of the concrete strength or reinforced ratio, both the flexure and shear capacity increase. Based on numerical results, a simplified method and a semi analytical equation for deriving the P-I diagram are proposed for different failure modes and damage levels.
