The process of ground vehicle dynamic gravimetry is inevitably affected by the carrier’s maneuvering acceleration,which makes the result contain a large amount of dynamic error.In this paper,we propose a dynamic erro...The process of ground vehicle dynamic gravimetry is inevitably affected by the carrier’s maneuvering acceleration,which makes the result contain a large amount of dynamic error.In this paper,we propose a dynamic error suppression method of gravimetry based on the high-precision acquisition of external velocity for compensating the horizontal error of the inertial plat-form.On the basis of platform gravity measurement,firstly,the dynamic performance of the system is enhanced by optimizing the horizontal damping network of the inertial platform and selecting its parameter.Secondly,an improved federal Kalman filtering algorithm and a fault diagnosis method are designed using strapdown inertial navigation system(SINS),odometer(OD),and laser Doppler velocimeter(LDV).Simulation validates that these methods can improve the accuracy and robustness of the external velocity acquisition.Three survey lines are selected in Tianjin,China,for the gravimetry experiments with different maneuvering levels,and the results demonstrate that after dynamic error suppression,the internal coincidence accuracies of smooth and uniform operation,obvious acceleration and deceleration operation,and high-dynamic operation are improved by 70.2%,73.6%,and 77.9%to reach 0.81 mGal,1.30 mGal,and 1.94 mGal,respectively,and the external coinci-dence accuracies during smooth and uniform operation are improved by 48.6%up to 1.66 mGal.It is shown that the pro-posed method can effectively suppress the dynamic error,and that the accuracy improvement increases with carrier maneuver-ability.However,the amount of residual error that can not be entirely eliminated increases as well,so the ground vehicle dynamic gravimetry should be maintained in the carrier for smooth and uniform operation.展开更多
A study was conducted to analyze the deformation mechanism of strongly weathered quartz schist in the Daliangshan Tunnel,located in the western Transverse Mountain area.A large deformation problem was experienced duri...A study was conducted to analyze the deformation mechanism of strongly weathered quartz schist in the Daliangshan Tunnel,located in the western Transverse Mountain area.A large deformation problem was experienced during the tunnel construction.To mitigate this problem,a support system was designed incorporating negative Poisson ratio(NPR)anchor cables with negative Poisson ratio effect.Physical model experiments,field experiments,and numerical simulation experiments were conducted to investigate the compensation mechanical behavior of NPR anchor cables.The large deformations of soft rocks in the Daliangshan Tunnel are caused by a high ground stress,a high degree of joint fracture development,and a high degree of surrounding rock fragmentation.A compensation mechanics support system combining long and short NPR anchor cables was suggested to provide sufficient counter-support force(approximately 350 kN)for the surrounding rock inside the tunnel.Comparing the NPR anchor cable support system with the original support system used in the Daliangshan tunnel showed that an NPR anchor cable support system,combining cables of 6.3 m and 10.3 m in length,effectively prevented convergence of surrounding rock deformation,and the integrated settlement convergence value remained below 300 mm.This study provides an effective scientific basis for resolving large deformation problems in deeply buried soft rocks in western transverse mountain areas.展开更多
Engineering shallow,large-span rock tunnels challenges deformation control and escalates construction costs.This study investigates the excavation compensation method(ECM)and its associated technologies to address the...Engineering shallow,large-span rock tunnels challenges deformation control and escalates construction costs.This study investigates the excavation compensation method(ECM)and its associated technologies to address these issues.Utilizing five key technologies,the ECM effectively modulates radial stress post-excavation,redistributes stress in the surrounding rock,and eliminates tensile stress at the excavation face.Pre-tensioning measures further enhance the rock’s residual strength,establishing a new stability equilibrium.Field tests corroborate the method’s effectiveness,demonstrating a crown settlement reduction of 3–8 mm,a nearly 50%decrease compared to conventional construction approaches.Additionally,material consumption and construction duration were reduced by approximately 30%–35%and 1.75 months per 100 m,respectively.Thus,the ECM represents a significant innovation in enhancing the stability and construction efficiency of large-span rock tunnels,marking a novel contribution to the engineering field.展开更多
To analyze the influence of time synchronization error,phase synchronization error,frequency synchronization error,internal delay of the transceiver system,and range error and angle error between the unit radars on th...To analyze the influence of time synchronization error,phase synchronization error,frequency synchronization error,internal delay of the transceiver system,and range error and angle error between the unit radars on the target detection performance,firstly,a spatial detection model of distributed high-frequency surface wave radar(distributed-HFSWR)is established in this paper.In this model,a method for accurate extraction of direct wave spectrum based on curve fitting is proposed to obtain accurate system internal delay and frequency synchronization error under complex electromagnetic environment background and low signal to noise ratio(SNR),and to compensate for the shift of range and Doppler frequency caused by time-frequency synchronization error.The direct wave component is extracted from the spectrum,the range estimation error and Doppler estimation error are reduced by the method of curve fitting,and the fitting accuracy of the parameters is improved.Then,the influence of frequency synchronization error on target range and radial Doppler velocity is quantitatively analyzed.The relationship between frequency synchronization error and radial Doppler velocity shift and range shift is given.Finally,the system synchronization parameters of the trial distributed-HFSWR are obtained by the proposed spectrum extraction method based on curve fitting,the experimental data is compensated to correct the shift of the target,and finally the correct target parameter information is obtained.Simulations and experimental results demonstrate the superiority and correctness of the proposed method,theoretical derivation and detection model proposed in this paper.展开更多
To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design...To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design problem can be solved using QFT but it fails to guarantee a high precision tracking. This problem is solved by a robust digital QFT control scheme based on zero phase error （ZPE） feed forward compensation. This scheme consists of two parts： a QFT controller in the closed-loop system and a ZPE feed-forward compensator. Digital QFT controller is designed to overcome the uncertainties in the system. Digital ZPE feed forward controller is used to improve the tracking precision. Simulation and real-time examples for flight simulator servo system indicate that this control scheme can guarantee both high robust performance and high position tracking precision.展开更多
The forest ecological compensation is an important factor to balance the interests of different areas for sustainable development and environment protection. Mudanjiang City in Heilongjiang Province of China is rich o...The forest ecological compensation is an important factor to balance the interests of different areas for sustainable development and environment protection. Mudanjiang City in Heilongjiang Province of China is rich of forest resources. The forestry coverage rate reached 62.3% in 2014, after forestry conservation program from 2002. The authors explored the factors impacted on forest ecological compensation in Mudanjiang City, which was a demonstration as a case study, through experts＇ evaluation scores and AHP methodology to analyze the forest ecological compensation factors and lay the foundation for the establishment of ecological compensation mechanism. At the same time, we provided an example to explore the effective way and speed up the establishment of ecological compensation mechanism. The study found that the main factors that determined forest ecological compensation in Mudanjiang City were ecology and natural resources. Based on the analyses, some suggestions were put forward to promote the mechanism in a sustainable way.展开更多
The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of ...The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of the thermal error modeling for machine tools, a new approach of regression orthogonal design is proposed, which combines the statistic theory with machine structures, surrounding condition, engineering judgements, and experience in modeling. A whole computation and analysis procedure is given. Therefore, the model got from this method are more robust and practical than those got from the present method that depends on the modeling data completely. At last more than 100 applications of CNC turning center with only one thermal error model are given. The cutting diameter variation reduces from more than 35 μm to about 12 μm with the orthogonal regression modeling and compensation of thermal error.展开更多
The natural frequency of the electrohydraulic system in mobile machinery is always very low,which brings difficulties to the controller design.To improve the tracking performance of the hydraulic system,mathematical m...The natural frequency of the electrohydraulic system in mobile machinery is always very low,which brings difficulties to the controller design.To improve the tracking performance of the hydraulic system,mathematical modeling of the electrohydraulic lifting system and the rubber hose was accomplished according to an electrohydraulic lifting test rig built in the laboratory.Then,valve compensation strategy,including spool opening compensation (SOC) and dead zone compensation (DZC),was designed based on the flow-pressure characteristic of a closed-centered proportional valve.Comparative experiments on point-to-point trajectory tracking between a proportional controller with the proposed compensations and a traditional PI controller were conducted.Experiment results show that the maximal absolute values of the tracking error are reduced from 0.039 m to 0.019 m for the slow point-to-point motion trajectory and from 0.085 m to 0.054 m for the fast point-to-point motion trajectory with the proposed compensations.Moreover,tracking error of the proposed controller was analyzed and corresponding suggestions to reduce the tracking error were put forward.展开更多
A comparison of the effectiveness of installing reactive power compensators,such as shunt capacitors,static var compensators(SVCs),and static synchronous compensators(STATCOMs),was presented in large-scale power netwo...A comparison of the effectiveness of installing reactive power compensators,such as shunt capacitors,static var compensators(SVCs),and static synchronous compensators(STATCOMs),was presented in large-scale power networks.A suitable bus was first identified using modal analysis method.The single shunt capacitor,single SVC,and single STATCOM were installed separately on the most critical bus.The effects of the installation of different devices on power loss reduction,voltage profile improvement,and voltage stability margin enhancement were examined and compared for 57-and 118-bus transmission systems.The comparative study results show that SVC,and STATCOM are expensive compared to shunt capacitor,yet the effect of installing STATCOM is better than SVC and the effect of installing SVC is better than that of shunt capacitor in achieving power loss reduction,voltage profile improvement and voltage stability margin enhancement.展开更多
On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point a...On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point are established according to the three usual methods of mounting workpieces on a turning machine. Further a prediction system for diameter errors is developed; a new method, called discrete nodes output, is presented and applied to expressing workpiece diameter errors at given points along the part axis, then off-line compensation is implemented according to the prediction values to diminish machining errors. The results indicate that the method can diminish diameter errors more than 70%, greatly improve the machining accuracy of bars.展开更多
An adaptive actuator failure compensation control scheme is developed using an indirect adaptive control method,by calculating the controller parameters from adaptive estimates of system parameters and actuator failur...An adaptive actuator failure compensation control scheme is developed using an indirect adaptive control method,by calculating the controller parameters from adaptive estimates of system parameters and actuator failure parameters.A key technical issue is how to deal with the actuator failure uncertainties such as failure pattern,time and values.A complete parametrization covering all possible failures is used to solve this issue for adaptive parameter estimation.A simultaneous mapping from the estimated system/failure parameters to the controller parameters is employed to make the control system capable of ensuring the desired system performance under failures,which is verified by simulation results.展开更多
According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accur...According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.展开更多
Adaptive antenna arrays have been used to mitigate the interference on global navigation satellite system（GNSS） receivers. The performance of interference mitigation depends on the beamforming algorithms adopted by ...Adaptive antenna arrays have been used to mitigate the interference on global navigation satellite system（GNSS） receivers. The performance of interference mitigation depends on the beamforming algorithms adopted by the antenna array. However,the adaptive beamforming will change the array pattern in realtime, which has the potential to introduce phase center biases into the antenna array. For precise applications, these phase biases must be mitigated or compensated because they will bring errors in code phase and carrier phase measurements. A novel adaptive beamforming algorithm is proposed firstly, then the phase bias induced by the proposed algorithm is estimated, and finally a compensation strategy is addressed. Simulations demonstrate that the proposed beamforming algorithm suppresses effectively the strong interference and improves significantly the capturing performance of GNSS signals. Simultaneously, the bias compensation method avoids the loss of the carrier phase lock and reduces the phase measurement errors for GNSS receivers.展开更多
This work presents an integrated pressure-tracking controller for a novel electro-hydraulic brake(EHB) system considering friction and hydraulic disturbances. To this end, a mathematical model of an EHB system, consis...This work presents an integrated pressure-tracking controller for a novel electro-hydraulic brake(EHB) system considering friction and hydraulic disturbances. To this end, a mathematical model of an EHB system, consisting of actuator and hydraulic sub-systems, is derived for describing the fundamental dynamics of the system and designing the controller. Due to sensor inaccuracy and measurement noise, a Kalman filter is constructed to estimate push rod stroke for generating desired master cylinder pressure. To improve pressure-tracking accuracy, a linear friction model is generated by linearizing the nonlinear Tustin friction model, and the unmodeled friction disturbances are assumed unknown but bounded. A sliding mode controller is designed for compensating friction disturbances, and the stability of the controller is investigated using the Lyapunov method. The performance of the proposed integrated controller is evaluated with a hardware-in-the-loop(HIL) test platform equipped with the EHB prototype. The test results demonstrate that the EHB system with the proposed integrated controller not only achieves good pressure-tracking performance, but also maintains robustness to friction disturbances.展开更多
In order to validate the simulation model and develop heave compensation control strategy,heave compensation model tests were performed.The model test installation includes themining ship motion simulator,the heave co...In order to validate the simulation model and develop heave compensation control strategy,heave compensation model tests were performed.The model test installation includes themining ship motion simulator,the heave compensation system,the lifting pipe simulator,the buffer simulator and the water pool.The tests ofmining ship motion simulator show that it is able to perform under the predetermined attitude path smoothly and can meet the requirements of themining ship motions.The heave compensation effect is more than 60% under random wave and the goal is set to be 50%.The model test results indicate that this heave compensation system is effective and feasible.展开更多
LuGre model has been widely used in friction modeling and compensation.However,the new friction regime,named prestiction regime,cannot be accurately characterized by LuGre model in the latest research.With the extensi...LuGre model has been widely used in friction modeling and compensation.However,the new friction regime,named prestiction regime,cannot be accurately characterized by LuGre model in the latest research.With the extensive experimental observations of friction behaviors in the prestiction,some variables were abstracted to depict the rules in the prestiction regime.Based upon the knowledge of friction modeling,a novel friction model including the presliding regime,the gross sliding regime and the prestiction regime was then presented to overcome the shortcomings of the LuGre model.The reason that LuGre model cannot estimate the prestiction friction was analyzed in theory.Feasibility analysis of the proposed model in modeling the prestiction friction was also addressed.A parameter identification method for the proposed model based on multilevel coordinate search algorithm was presented.The proposed friction compensation strategy was composed of a nonlinear friction observer and a feedforward mechanism.The friction observer was designed to estimate the friction force in the presliding and the gross sliding regimes.And the friction force was estimated based on the model in the prestiction regime.The comparative trajectory tracking experiments were conducted on a simulator of inertially stabilization platforms among three control schemes:the single proportional–derivative(PD)control,the PD with LuGre model-based compensation and the PD with compensator based on the presented model.The experimental results reveal that the control scheme based on the proposed model has the best tracking performance.It reduces the peak-to-peak value(PPV)of tracking error to 0.2 mrad,which is improved almost 50%compared with the PD with LuGre model-based compensation.Compared to the single PD control,it reduces the PPV of error by 66.7%.展开更多
The stability for a class of linear neutral systems with time-varying delays is studied in this paper, where delay in neutral-type term includes a fast-varying case (i.e., the derivative of delay is more than one), wh...The stability for a class of linear neutral systems with time-varying delays is studied in this paper, where delay in neutral-type term includes a fast-varying case (i.e., the derivative of delay is more than one), which has never been considered in current literature. The less conservative delaydependent stability criteria for this system are proposed by applying new Lyapunov-Krasovskii functional and novel polynomials with time-varying delay (PTVD) compensation technique. The aim to deal with systems with fast-varying neutral-type delay can be achieved by using the new functional. The benefit brought by applying the PTVD compensation technique is that some useful elements can be included in criteria, which are generally ignored when estimating the upper bound of derivative of Lyapunov-Krasovskii functional. A numerical example is provided to verify the effectiveness of the proposed results.展开更多
Inverse synthetic aperture radar(ISAR)imaging of the target with the non-rigid body is very important in the field of radar signal processing.In this paper,a motion compensation method combined with the preprocessing ...Inverse synthetic aperture radar(ISAR)imaging of the target with the non-rigid body is very important in the field of radar signal processing.In this paper,a motion compensation method combined with the preprocessing and global technique is proposed to reduce the influence of micro-motion components in the fast time domain,and the micro-Doppler(m-D)signal in the slow time domain is separated by the improved complex-valued empirical-mode decomposition(CEMD)algorithm,which makes the m-D signal more effectively distinguishable from the signal for the main body by translating the target to the Doppler center.Then,a better focused ISAR image of the target with the non-rigid body can be obtained consequently.Results of the simulated and raw data demonstrate the effectiveness of the algorithm.展开更多
Synthetic aperture radar(SAR) is usually sensitive to trajectory deviations that cause serious motion error in the recorded data. In this paper, a coherent range-dependent mapdrift(CRDMD) algorithm is developed to acc...Synthetic aperture radar(SAR) is usually sensitive to trajectory deviations that cause serious motion error in the recorded data. In this paper, a coherent range-dependent mapdrift(CRDMD) algorithm is developed to accommodate the range-variant motion errors. By utilizing the algorithm as an estimate core, robust motion compensation strategy is proposed for unmanned aerial vehicle(UAV) SAR imagery. CRDMD outperforms the conventional map-drift algorithms in both accuracy and efficiency. Real data experiments show that the proposed approach is appropriate for precise motion compensation for UAV SAR.展开更多
In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error m...In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error model for the laser annealing table was established. It supports the identification of 7 geometric errors affecting the annealing accuracy. An original identification method was presented to recognize these geometric errors. Positioning errors of 5 lines in the workspace were measured by a laser interferometer, and the 7 geometric errors were identified by the proposed algorithm. Finally, a software-based error compensation method was adopted, and a compensation mechanism was developed in a postprocessor based on LabVIEW. The identified geometric errors can be compensated by converting ideal NC codes to actual NC codes. A validation experiment has been conducted on the laser annealing table, and the results indicate that positioning errors of two validation lines decreased from ±37 μm and ±33 μm to ±5 μm and ±4.5 μm, respectively. The geometric error modeling, identification and compensation method presented in this work can be straightforwardly extended to any configurations of 2-dimensional worktable.展开更多
基金supported by the Shanxi Provincial Natural Science Basic Research Program Young Talent Project(S2019-JC-QN-2408).
文摘The process of ground vehicle dynamic gravimetry is inevitably affected by the carrier’s maneuvering acceleration,which makes the result contain a large amount of dynamic error.In this paper,we propose a dynamic error suppression method of gravimetry based on the high-precision acquisition of external velocity for compensating the horizontal error of the inertial plat-form.On the basis of platform gravity measurement,firstly,the dynamic performance of the system is enhanced by optimizing the horizontal damping network of the inertial platform and selecting its parameter.Secondly,an improved federal Kalman filtering algorithm and a fault diagnosis method are designed using strapdown inertial navigation system(SINS),odometer(OD),and laser Doppler velocimeter(LDV).Simulation validates that these methods can improve the accuracy and robustness of the external velocity acquisition.Three survey lines are selected in Tianjin,China,for the gravimetry experiments with different maneuvering levels,and the results demonstrate that after dynamic error suppression,the internal coincidence accuracies of smooth and uniform operation,obvious acceleration and deceleration operation,and high-dynamic operation are improved by 70.2%,73.6%,and 77.9%to reach 0.81 mGal,1.30 mGal,and 1.94 mGal,respectively,and the external coinci-dence accuracies during smooth and uniform operation are improved by 48.6%up to 1.66 mGal.It is shown that the pro-posed method can effectively suppress the dynamic error,and that the accuracy improvement increases with carrier maneuver-ability.However,the amount of residual error that can not be entirely eliminated increases as well,so the ground vehicle dynamic gravimetry should be maintained in the carrier for smooth and uniform operation.
基金Project(41941018)supported by the National Natural Science Foundation of China for the Special Project FundingProject(22-JKCF-08)supported by the Study on in-situ Stress Database and 3D in-situ Stress Inversion Technology of Highway Tunnel in Shanxi Province,China+1 种基金Project(2022-JKKJ-6)supported by the Study on Disaster Mechanism and NPR Anchor Cable Prevention and Control of Coal Mining Caving Subsidence in Operating Tunnel in Mountainous Area,ChinaProject(BBJ2024032)supported by the Fundamental Research Funds for the Central Universities(PhD Top Innovative Talents Fund of CUMTB),China。
文摘A study was conducted to analyze the deformation mechanism of strongly weathered quartz schist in the Daliangshan Tunnel,located in the western Transverse Mountain area.A large deformation problem was experienced during the tunnel construction.To mitigate this problem,a support system was designed incorporating negative Poisson ratio(NPR)anchor cables with negative Poisson ratio effect.Physical model experiments,field experiments,and numerical simulation experiments were conducted to investigate the compensation mechanical behavior of NPR anchor cables.The large deformations of soft rocks in the Daliangshan Tunnel are caused by a high ground stress,a high degree of joint fracture development,and a high degree of surrounding rock fragmentation.A compensation mechanics support system combining long and short NPR anchor cables was suggested to provide sufficient counter-support force(approximately 350 kN)for the surrounding rock inside the tunnel.Comparing the NPR anchor cable support system with the original support system used in the Daliangshan tunnel showed that an NPR anchor cable support system,combining cables of 6.3 m and 10.3 m in length,effectively prevented convergence of surrounding rock deformation,and the integrated settlement convergence value remained below 300 mm.This study provides an effective scientific basis for resolving large deformation problems in deeply buried soft rocks in western transverse mountain areas.
基金Projects(42377148,51674265)supported by the National Natural Science Foundation of ChinaProject(2018YFC0603705)supported by the National Key Research and Development Program of China。
文摘Engineering shallow,large-span rock tunnels challenges deformation control and escalates construction costs.This study investigates the excavation compensation method(ECM)and its associated technologies to address these issues.Utilizing five key technologies,the ECM effectively modulates radial stress post-excavation,redistributes stress in the surrounding rock,and eliminates tensile stress at the excavation face.Pre-tensioning measures further enhance the rock’s residual strength,establishing a new stability equilibrium.Field tests corroborate the method’s effectiveness,demonstrating a crown settlement reduction of 3–8 mm,a nearly 50%decrease compared to conventional construction approaches.Additionally,material consumption and construction duration were reduced by approximately 30%–35%and 1.75 months per 100 m,respectively.Thus,the ECM represents a significant innovation in enhancing the stability and construction efficiency of large-span rock tunnels,marking a novel contribution to the engineering field.
基金supported by the National Natural Science Foundation of China(61701140).
文摘To analyze the influence of time synchronization error,phase synchronization error,frequency synchronization error,internal delay of the transceiver system,and range error and angle error between the unit radars on the target detection performance,firstly,a spatial detection model of distributed high-frequency surface wave radar(distributed-HFSWR)is established in this paper.In this model,a method for accurate extraction of direct wave spectrum based on curve fitting is proposed to obtain accurate system internal delay and frequency synchronization error under complex electromagnetic environment background and low signal to noise ratio(SNR),and to compensate for the shift of range and Doppler frequency caused by time-frequency synchronization error.The direct wave component is extracted from the spectrum,the range estimation error and Doppler estimation error are reduced by the method of curve fitting,and the fitting accuracy of the parameters is improved.Then,the influence of frequency synchronization error on target range and radial Doppler velocity is quantitatively analyzed.The relationship between frequency synchronization error and radial Doppler velocity shift and range shift is given.Finally,the system synchronization parameters of the trial distributed-HFSWR are obtained by the proposed spectrum extraction method based on curve fitting,the experimental data is compensated to correct the shift of the target,and finally the correct target parameter information is obtained.Simulations and experimental results demonstrate the superiority and correctness of the proposed method,theoretical derivation and detection model proposed in this paper.
基金This project was supported by the Aeronautics Foundation of China (00E51022).
文摘To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design problem can be solved using QFT but it fails to guarantee a high precision tracking. This problem is solved by a robust digital QFT control scheme based on zero phase error （ZPE） feed forward compensation. This scheme consists of two parts： a QFT controller in the closed-loop system and a ZPE feed-forward compensator. Digital QFT controller is designed to overcome the uncertainties in the system. Digital ZPE feed forward controller is used to improve the tracking precision. Simulation and real-time examples for flight simulator servo system indicate that this control scheme can guarantee both high robust performance and high position tracking precision.
基金Supported by by the National Social Science(14BGL090)Humanities and Social Science Project of Educational Department in Heilongjiang Province(12542019)
文摘The forest ecological compensation is an important factor to balance the interests of different areas for sustainable development and environment protection. Mudanjiang City in Heilongjiang Province of China is rich of forest resources. The forestry coverage rate reached 62.3% in 2014, after forestry conservation program from 2002. The authors explored the factors impacted on forest ecological compensation in Mudanjiang City, which was a demonstration as a case study, through experts＇ evaluation scores and AHP methodology to analyze the forest ecological compensation factors and lay the foundation for the establishment of ecological compensation mechanism. At the same time, we provided an example to explore the effective way and speed up the establishment of ecological compensation mechanism. The study found that the main factors that determined forest ecological compensation in Mudanjiang City were ecology and natural resources. Based on the analyses, some suggestions were put forward to promote the mechanism in a sustainable way.
文摘The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of the thermal error modeling for machine tools, a new approach of regression orthogonal design is proposed, which combines the statistic theory with machine structures, surrounding condition, engineering judgements, and experience in modeling. A whole computation and analysis procedure is given. Therefore, the model got from this method are more robust and practical than those got from the present method that depends on the modeling data completely. At last more than 100 applications of CNC turning center with only one thermal error model are given. The cutting diameter variation reduces from more than 35 μm to about 12 μm with the orthogonal regression modeling and compensation of thermal error.
基金Project(2006CB705400)supported by the National Basic Research Program of China
文摘The natural frequency of the electrohydraulic system in mobile machinery is always very low,which brings difficulties to the controller design.To improve the tracking performance of the hydraulic system,mathematical modeling of the electrohydraulic lifting system and the rubber hose was accomplished according to an electrohydraulic lifting test rig built in the laboratory.Then,valve compensation strategy,including spool opening compensation (SOC) and dead zone compensation (DZC),was designed based on the flow-pressure characteristic of a closed-centered proportional valve.Comparative experiments on point-to-point trajectory tracking between a proportional controller with the proposed compensations and a traditional PI controller were conducted.Experiment results show that the maximal absolute values of the tracking error are reduced from 0.039 m to 0.019 m for the slow point-to-point motion trajectory and from 0.085 m to 0.054 m for the fast point-to-point motion trajectory with the proposed compensations.Moreover,tracking error of the proposed controller was analyzed and corresponding suggestions to reduce the tracking error were put forward.
文摘A comparison of the effectiveness of installing reactive power compensators,such as shunt capacitors,static var compensators(SVCs),and static synchronous compensators(STATCOMs),was presented in large-scale power networks.A suitable bus was first identified using modal analysis method.The single shunt capacitor,single SVC,and single STATCOM were installed separately on the most critical bus.The effects of the installation of different devices on power loss reduction,voltage profile improvement,and voltage stability margin enhancement were examined and compared for 57-and 118-bus transmission systems.The comparative study results show that SVC,and STATCOM are expensive compared to shunt capacitor,yet the effect of installing STATCOM is better than SVC and the effect of installing SVC is better than that of shunt capacitor in achieving power loss reduction,voltage profile improvement and voltage stability margin enhancement.
文摘On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point are established according to the three usual methods of mounting workpieces on a turning machine. Further a prediction system for diameter errors is developed; a new method, called discrete nodes output, is presented and applied to expressing workpiece diameter errors at given points along the part axis, then off-line compensation is implemented according to the prediction values to diminish machining errors. The results indicate that the method can diminish diameter errors more than 70%, greatly improve the machining accuracy of bars.
基金supported by the US National Science Foundation (ECS0601475)the National Natural Science Foundation of China (60904042)
文摘An adaptive actuator failure compensation control scheme is developed using an indirect adaptive control method,by calculating the controller parameters from adaptive estimates of system parameters and actuator failure parameters.A key technical issue is how to deal with the actuator failure uncertainties such as failure pattern,time and values.A complete parametrization covering all possible failures is used to solve this issue for adaptive parameter estimation.A simultaneous mapping from the estimated system/failure parameters to the controller parameters is employed to make the control system capable of ensuring the desired system performance under failures,which is verified by simulation results.
基金Supported by the National Natural Science Foundation of China(51275145)
文摘According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.
基金supported by the National Natural Science Foundation of China(61301094)the Postdoctoral Science Foundation of China(2014M552490)
文摘Adaptive antenna arrays have been used to mitigate the interference on global navigation satellite system（GNSS） receivers. The performance of interference mitigation depends on the beamforming algorithms adopted by the antenna array. However,the adaptive beamforming will change the array pattern in realtime, which has the potential to introduce phase center biases into the antenna array. For precise applications, these phase biases must be mitigated or compensated because they will bring errors in code phase and carrier phase measurements. A novel adaptive beamforming algorithm is proposed firstly, then the phase bias induced by the proposed algorithm is estimated, and finally a compensation strategy is addressed. Simulations demonstrate that the proposed beamforming algorithm suppresses effectively the strong interference and improves significantly the capturing performance of GNSS signals. Simultaneously, the bias compensation method avoids the loss of the carrier phase lock and reduces the phase measurement errors for GNSS receivers.
基金Projects(51405008,51175015)supported by the National Natural Science Foundation of ChinaProject(2012AA110904)supported by the National High Technology Research and Development Program of China
文摘This work presents an integrated pressure-tracking controller for a novel electro-hydraulic brake(EHB) system considering friction and hydraulic disturbances. To this end, a mathematical model of an EHB system, consisting of actuator and hydraulic sub-systems, is derived for describing the fundamental dynamics of the system and designing the controller. Due to sensor inaccuracy and measurement noise, a Kalman filter is constructed to estimate push rod stroke for generating desired master cylinder pressure. To improve pressure-tracking accuracy, a linear friction model is generated by linearizing the nonlinear Tustin friction model, and the unmodeled friction disturbances are assumed unknown but bounded. A sliding mode controller is designed for compensating friction disturbances, and the stability of the controller is investigated using the Lyapunov method. The performance of the proposed integrated controller is evaluated with a hardware-in-the-loop(HIL) test platform equipped with the EHB prototype. The test results demonstrate that the EHB system with the proposed integrated controller not only achieves good pressure-tracking performance, but also maintains robustness to friction disturbances.
基金Project(50675226) supported by the National Natural Science Foundation of China Project(DYXM-115-04-02-01) supported by the Eleventh Five-Year Plan of China
文摘In order to validate the simulation model and develop heave compensation control strategy,heave compensation model tests were performed.The model test installation includes themining ship motion simulator,the heave compensation system,the lifting pipe simulator,the buffer simulator and the water pool.The tests ofmining ship motion simulator show that it is able to perform under the predetermined attitude path smoothly and can meet the requirements of themining ship motions.The heave compensation effect is more than 60% under random wave and the goal is set to be 50%.The model test results indicate that this heave compensation system is effective and feasible.
基金Projects(51135009,51105371) supported by the National Natural Science Foundation of China
文摘LuGre model has been widely used in friction modeling and compensation.However,the new friction regime,named prestiction regime,cannot be accurately characterized by LuGre model in the latest research.With the extensive experimental observations of friction behaviors in the prestiction,some variables were abstracted to depict the rules in the prestiction regime.Based upon the knowledge of friction modeling,a novel friction model including the presliding regime,the gross sliding regime and the prestiction regime was then presented to overcome the shortcomings of the LuGre model.The reason that LuGre model cannot estimate the prestiction friction was analyzed in theory.Feasibility analysis of the proposed model in modeling the prestiction friction was also addressed.A parameter identification method for the proposed model based on multilevel coordinate search algorithm was presented.The proposed friction compensation strategy was composed of a nonlinear friction observer and a feedforward mechanism.The friction observer was designed to estimate the friction force in the presliding and the gross sliding regimes.And the friction force was estimated based on the model in the prestiction regime.The comparative trajectory tracking experiments were conducted on a simulator of inertially stabilization platforms among three control schemes:the single proportional–derivative(PD)control,the PD with LuGre model-based compensation and the PD with compensator based on the presented model.The experimental results reveal that the control scheme based on the proposed model has the best tracking performance.It reduces the peak-to-peak value(PPV)of tracking error to 0.2 mrad,which is improved almost 50%compared with the PD with LuGre model-based compensation.Compared to the single PD control,it reduces the PPV of error by 66.7%.
基金Supported by National Basic Research Program of China(973 Program)(2009CB320601)National Natural Science Foundation of China(50977008,60774048)the Program for Cheung Kong Scholars
文摘The stability for a class of linear neutral systems with time-varying delays is studied in this paper, where delay in neutral-type term includes a fast-varying case (i.e., the derivative of delay is more than one), which has never been considered in current literature. The less conservative delaydependent stability criteria for this system are proposed by applying new Lyapunov-Krasovskii functional and novel polynomials with time-varying delay (PTVD) compensation technique. The aim to deal with systems with fast-varying neutral-type delay can be achieved by using the new functional. The benefit brought by applying the PTVD compensation technique is that some useful elements can be included in criteria, which are generally ignored when estimating the upper bound of derivative of Lyapunov-Krasovskii functional. A numerical example is provided to verify the effectiveness of the proposed results.
基金supported by the National Natural Science Foundation of China(61871146)the Fundamental Research Funds for the Central Universitiesthe State Key Laboratory of Millimeter Waves(K202022)。
文摘Inverse synthetic aperture radar(ISAR)imaging of the target with the non-rigid body is very important in the field of radar signal processing.In this paper,a motion compensation method combined with the preprocessing and global technique is proposed to reduce the influence of micro-motion components in the fast time domain,and the micro-Doppler(m-D)signal in the slow time domain is separated by the improved complex-valued empirical-mode decomposition(CEMD)algorithm,which makes the m-D signal more effectively distinguishable from the signal for the main body by translating the target to the Doppler center.Then,a better focused ISAR image of the target with the non-rigid body can be obtained consequently.Results of the simulated and raw data demonstrate the effectiveness of the algorithm.
基金supported by the Key R&D Program Projects in Hainan Province (ZDY 2019008)the State Key Laboratory of Rail T ransit Engineering Information (SKLK22-08)。
文摘Synthetic aperture radar(SAR) is usually sensitive to trajectory deviations that cause serious motion error in the recorded data. In this paper, a coherent range-dependent mapdrift(CRDMD) algorithm is developed to accommodate the range-variant motion errors. By utilizing the algorithm as an estimate core, robust motion compensation strategy is proposed for unmanned aerial vehicle(UAV) SAR imagery. CRDMD outperforms the conventional map-drift algorithms in both accuracy and efficiency. Real data experiments show that the proposed approach is appropriate for precise motion compensation for UAV SAR.
基金Projects(2012ZX04010-011,2009ZX02037-02) supported by the Key National Science and Technology Project of China
文摘In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error model for the laser annealing table was established. It supports the identification of 7 geometric errors affecting the annealing accuracy. An original identification method was presented to recognize these geometric errors. Positioning errors of 5 lines in the workspace were measured by a laser interferometer, and the 7 geometric errors were identified by the proposed algorithm. Finally, a software-based error compensation method was adopted, and a compensation mechanism was developed in a postprocessor based on LabVIEW. The identified geometric errors can be compensated by converting ideal NC codes to actual NC codes. A validation experiment has been conducted on the laser annealing table, and the results indicate that positioning errors of two validation lines decreased from ±37 μm and ±33 μm to ±5 μm and ±4.5 μm, respectively. The geometric error modeling, identification and compensation method presented in this work can be straightforwardly extended to any configurations of 2-dimensional worktable.
