The ductile-to-brittle transition temperature(DBTT)of high strength steels can be optimized by tailoring microstructure and crystallographic orientation characteristics,where the start cooling temperature plays a key ...The ductile-to-brittle transition temperature(DBTT)of high strength steels can be optimized by tailoring microstructure and crystallographic orientation characteristics,where the start cooling temperature plays a key role.In this work,X70 steels with different start cooling temperatures were prepared through thermo-mechanical control process.The quasi-polygonal ferrite(QF),granular bainite(GB),bainitic ferrite(BF)and martensite-austenite constituents were formed at the start cooling temperatures of 780℃(C1),740℃(C2)and 700℃(C3).As start cooling temperature decreased,the amount of GB decreased,the microstructure of QF and BF increased.Microstructure characteristics of the three samples,such as high-angle grain boundaries(HAGBs),MA constituents and crystallographic orientation,also varied with the start cooling temperatures.C2 sample had the lowest DBTT value(−86℃)for its highest fraction of HAGBs,highest content of<110>oriented grains and lowest content of<001>oriented grains parallel to TD.The high density of{332}<113>and low density of rotated cube{001}<110>textures also contributed to the best impact toughness of C2 sample.In addition,a modified model was used in this paper to quantitatively predict the approximate DBTT value of steels.展开更多
The influence of crystallographic orientation on the void growth in FCC crystals was numerically simulated with 3D crystal plasticity finite element by using a 3D unit cell including a spherical void, and the rate-dep...The influence of crystallographic orientation on the void growth in FCC crystals was numerically simulated with 3D crystal plasticity finite element by using a 3D unit cell including a spherical void, and the rate-dependent crystal plasticity theory was implemented as a user material subroutine. The results of the simulations show that crystallographic orientation has significant influence on the growth behavior of the void. Different active slip systems of the regions around the void cause the discontinuity in lattice rotation around the void, and the corner-like region is formed. In the case of the void located at grain boundary, large heterogeneous deformation occurs between the two grains, and the equivalent plastic deformation along grain boundary near the void in the case of θ=45^o （θ is the angle between grain boundary direction and X-axis） is larger than the others. Large difference of orientation factor of the two grains leads to large equivalent plastic deformation along grain boundary, and the unit cell is more likely to fail by intergranular fracture.展开更多
The mechanical and microstructural properties as well as crystallographic textures of asymmetrically rolled low carbon steel were studied.The modelling of plastic deformation was carried out in two scales:in the macro...The mechanical and microstructural properties as well as crystallographic textures of asymmetrically rolled low carbon steel were studied.The modelling of plastic deformation was carried out in two scales:in the macro-scale,using the finite elements method,and in the crystallographic scale,using the polycrystalline deformation model.The internal stress distribution in the rolling gap was calculated using the finite elements method and these stresses were then applied to the polycrystalline elasto-plastic deformation model.Selected mechanical properties,namely residual stress distribution,deformation work,applied force and torques,and bend amplitude,were calculated.The diffraction measurements,X-ray and electron backscatter diffraction,enabled the examination of texture heterogeneity and selected microstructure characteristics.The predicted textures agree well with those determined experimentally.The plastic anisotropy of cold rolled ferritic steel samples,connected with texture,was expressed by Lankford coefficient.展开更多
基金Project(2018XK2301) supported by the Change-Zhu-Tan National Independent Innavation Demonstration Zone Special Program,China。
文摘The ductile-to-brittle transition temperature(DBTT)of high strength steels can be optimized by tailoring microstructure and crystallographic orientation characteristics,where the start cooling temperature plays a key role.In this work,X70 steels with different start cooling temperatures were prepared through thermo-mechanical control process.The quasi-polygonal ferrite(QF),granular bainite(GB),bainitic ferrite(BF)and martensite-austenite constituents were formed at the start cooling temperatures of 780℃(C1),740℃(C2)and 700℃(C3).As start cooling temperature decreased,the amount of GB decreased,the microstructure of QF and BF increased.Microstructure characteristics of the three samples,such as high-angle grain boundaries(HAGBs),MA constituents and crystallographic orientation,also varied with the start cooling temperatures.C2 sample had the lowest DBTT value(−86℃)for its highest fraction of HAGBs,highest content of<110>oriented grains and lowest content of<001>oriented grains parallel to TD.The high density of{332}<113>and low density of rotated cube{001}<110>textures also contributed to the best impact toughness of C2 sample.In addition,a modified model was used in this paper to quantitatively predict the approximate DBTT value of steels.
基金Project(2005CB623706) supported by the Major State Basic Research Development Program of China
文摘The influence of crystallographic orientation on the void growth in FCC crystals was numerically simulated with 3D crystal plasticity finite element by using a 3D unit cell including a spherical void, and the rate-dependent crystal plasticity theory was implemented as a user material subroutine. The results of the simulations show that crystallographic orientation has significant influence on the growth behavior of the void. Different active slip systems of the regions around the void cause the discontinuity in lattice rotation around the void, and the corner-like region is formed. In the case of the void located at grain boundary, large heterogeneous deformation occurs between the two grains, and the equivalent plastic deformation along grain boundary near the void in the case of θ=45^o （θ is the angle between grain boundary direction and X-axis） is larger than the others. Large difference of orientation factor of the two grains leads to large equivalent plastic deformation along grain boundary, and the unit cell is more likely to fail by intergranular fracture.
基金Projects(DEC-2011/01/B/ST8/07394,DEC-2011/01/D/ST8/07399)supported by the Polish National Centre for Science(NCN)The support of the Polish Ministry of Science and Higher Education and of the French ANR 05-BLAN-0383 project
文摘The mechanical and microstructural properties as well as crystallographic textures of asymmetrically rolled low carbon steel were studied.The modelling of plastic deformation was carried out in two scales:in the macro-scale,using the finite elements method,and in the crystallographic scale,using the polycrystalline deformation model.The internal stress distribution in the rolling gap was calculated using the finite elements method and these stresses were then applied to the polycrystalline elasto-plastic deformation model.Selected mechanical properties,namely residual stress distribution,deformation work,applied force and torques,and bend amplitude,were calculated.The diffraction measurements,X-ray and electron backscatter diffraction,enabled the examination of texture heterogeneity and selected microstructure characteristics.The predicted textures agree well with those determined experimentally.The plastic anisotropy of cold rolled ferritic steel samples,connected with texture,was expressed by Lankford coefficient.
