The effects of magnesium/polytetrafluoroethylene(Mg/PTFE)pyrotechnic compositions on the coupled flow field and reignition mechanism are important aspects governing the perfommance and range of base bleed projectiles(...The effects of magnesium/polytetrafluoroethylene(Mg/PTFE)pyrotechnic compositions on the coupled flow field and reignition mechanism are important aspects governing the perfommance and range of base bleed projectiles(BBPs).Owing to a decrease in pressure and temperature when the BBP leaves the muzzle,rapid depressurization occurs,which extinguishes the base bleed propellant.The Mg/PTFE py-rotechnic composition pressed in the igniter of the base bleed unit(BBU)provides additional energy to the BBU via a chemical reaction.Thus,the extinguished base bleed propellant is reignited under the effect of high-temperature combustion gas jets from the igniter.In this study,a numerical analysis is conducted to evaluate the effects of PTFE and Mg granularity as well as Mg/PTFE pyrotechnic compo-sitions.Owing to the rapid depressurization,the temperature and pressure was found to decrease fordifferent Mg/PIFE pyrotechnic compositions.However,the depressurization time increased as the PTFE granularity increased,the Mg granularity decreased,and the Mg content increased.When the pressure in the combustion chamber of the BBU decreased to the atmospheric pressure,the combustion gas jets from the igniter expand upstream(rather than downstream).However,these combustion gas jets exhibit different axial and radial expansion characteristics depending on the pyrotechnic compositions used,The results show that the reignition delay time,ta,of the base bleed propellant was 377.608,94.27,387.243,523.966,and 221.094 ms for cases A-E,respectively.Therefore,it was concluded that the Mg/PTFE pyrotechnic composition of case B was the most beneficial for the reignition of the base bleed propellant,with the earliest addition of energy and mass to the BBP.展开更多
Uranium ore is an essential material in the preparation of nuclear fuel for civilian and military uses.Uranium deposits are also important sources of energy for countries which depend heavily on nuclear power(e.g.Fran...Uranium ore is an essential material in the preparation of nuclear fuel for civilian and military uses.Uranium deposits are also important sources of energy for countries which depend heavily on nuclear power(e.g.France).展开更多
Source apportionment of particulate matters with aerodynamic diameter less than 10 μm （PM10） was conducted in the suburban area of Changsha, China. PM10 samples for 24 h collected with TEOM 1400a and ACCU system in...Source apportionment of particulate matters with aerodynamic diameter less than 10 μm （PM10） was conducted in the suburban area of Changsha, China. PM10 samples for 24 h collected with TEOM 1400a and ACCU system in July and October 2008 were chemically analyzed by the wavelength dispersive X-ray fluorescence （WD-XRF）. Source appointment was implemented by the principal component analysis/absolute principal component analysis （PCA/APCA） to identify the possible sources and to quantify the contributions of the sources to PM10. Results show that as the PM10 concentration is increased from （85.6±43.7） μg/m3 in July 2008 to （107.6±35.7） μg/m^3 in October 2008, the concentrations of the anthropogenic elements （P, S, C1, K, Mn, Ni, Cu, Zn, and Pb） are basically increased but concentrations of the natural elements （Na, Mg, Al, Si, Ca, Ti, and Fe） are essentially decreased. Six main sources of PM10 are identified in the suburban of Changsha, China： soil dust, secondary aerosols, domestic oil combustion, waste incineration, traffic emission, and industrial emission contribute 57.7%, 24.0%, 9.8%, 5.0%, 2.0%, and 1.5%, respectively. Soil dust and secondary aerosols are the two major sources of particulate air pollution in suburban area of Changsha, China, so effective measures should be taken to control these two particulate pollutants.展开更多
Upper atmosphere composition data were obtained for the last half year with a quadruple mass spectrometer on board spacecraft "SZ-2" launched on 10 Jan uary 2001. Based on the analysis of these data, the var...Upper atmosphere composition data were obtained for the last half year with a quadruple mass spectrometer on board spacecraft "SZ-2" launched on 10 Jan uary 2001. Based on the analysis of these data, the variations of atmospheric compositions in solar and geomagnetic quiet conditions are reported first, then a detailed discussion on the atmospheric composition variations under the so lar and geomagnetic disturbed conditions is given. The results show that near the altitude of 400 km the variations of main atmospheric compositions corre sponding to solar disturbances are more remarkable in the sunlit area than in the shade area. On the contrary, in geomagnetic disturbance events the corre sponding variations are more obvious in the shade area, an evident increase of N2 density at relatively higher latitudes was observed.展开更多
The phase compositions and properties of Ti3SiC2-based composites with SiC addition of 5%-30% in mass fraction fabricated by in-situ reaction and hot pressing sintering were studied. SiC addition effectively prevented...The phase compositions and properties of Ti3SiC2-based composites with SiC addition of 5%-30% in mass fraction fabricated by in-situ reaction and hot pressing sintering were studied. SiC addition effectively prevented TiC synthesis but facilitated SiC synthesis. The Ti3SiC2/Ti C-SiC composite had better oxidation resistance when SiC added quantity reached 20% but poorer oxidation resistance with SiC addition under 15% than Ti3SiC2/TiC composite at higher temperatures. There were more than half of the original SiC and a few Ti3SiC2 remaining in Ti3SiC2/Ti C-SiC with 20% SiC addition, but all constituents in Ti3Si2/TiC composite were oxidized after 12 h in air at 1500 °C. The oxidation scale thickness of TS30, 1505.78 μm, was near a half of that of T,2715 μm, at 1500 °C for 20 h. Ti3SiC2/Ti C composite had a flexural strength of 474 MPa, which was surpassed by Ti3SiC2/TiC-SiC composites when SiC added amount reached 15%. The strength reached the peak of 518 MPa at 20% SiC added amount.展开更多
The Lesser Himalaya in central Nepal consists of greenschist\|facies metasedimentary rocks, which are overthrust by the amphibolite\|facies rocks of the Higher Himalaya along the Upper Main Central Thrust (UMCT). Desp...The Lesser Himalaya in central Nepal consists of greenschist\|facies metasedimentary rocks, which are overthrust by the amphibolite\|facies rocks of the Higher Himalaya along the Upper Main Central Thrust (UMCT). Despite a number of works on metamorphism of the MCT zone and the Higher Himalaya, the low\|grade metamorphic rocks to the south of the MCT zone have not been studied yet.In the present study, an attempt was made to constrain the metamorphic events and thermal structure of the whole Lesser Himalaya by means of white mica (Ms) compositions. About 600Ms grains in 48 metapelitic samples from the Lesser Himalaya were analysed by the EPMA. Compositional zoning in individual Ms grains was checked by means of X\|ray compositional mapping. There exist wide intersample, intrasample and within grain compositional variations in Ms in the samples from the Lesser Himalaya. Sheared Ms phenocrysts in pegmatites and gneisses have compositions very close to that of the ideal muscovite. Detrital Ms show wide variation in phengite content, most of which are poor in phengite content, and are most probably derived from older higher\|grade metamorphic rocks.展开更多
Wild native Elymus(Elymus dahuricus)is one of the most important and valuable forage grass on Qinghai-Tibetan Plateau(QTP)pasture of China.It mainly distributes above sea-level of 1700 to 3000 m on the QTP.The objecti...Wild native Elymus(Elymus dahuricus)is one of the most important and valuable forage grass on Qinghai-Tibetan Plateau(QTP)pasture of China.It mainly distributes above sea-level of 1700 to 3000 m on the QTP.The objective of this study was to investigate how the nutritive composition of Elymus responsed to the changes of altitude in local environments.Two test sites located at Minghe and Huangzhong counties,in which four sampling plots were arranged with sea levels of 1714,1872,2097 and 2185 m in Minhe County,while other four in Huangzhong County were with sea-level of 2560,2613,2668 and 2775 m.The whole plants of Elymus during anthesis stage were collected from all the plots for determining the indexes of crude protein(CP),crude fat(CF),neutral detergent fiber(NDF),acid detergent fiber(ADF),crude ash(ASH),calcium(Ca)and phosphorus(P).The results showed that the content of CP,crude ash and Ca changed irregularly corresponding to the altitude in the two counties,but significant higher with CP(1.09%),Ash(0.33%)and Ca(0.34%)in the low altitude areas(1714-2185 m)than those in the high altitude areas.NDF and ADF in the low altitude areas were significantly lower by 5.35% and 2.61% compared with those in the high altitude areas.There was no significant difference of CF as well as P in plant from different altitudes.Comprehensive evaluation revealed that superior nutritional composition of Elymus dahuricus presented at the sampling plots of altitude of 1714 m in Minhe County.展开更多
The penetration-deflagration coupling damage performance of rod-like reactive shaped charge pene-trator(RRSCP)impacting thick steel plates is investigated by theoretical analysis and experiments.A penetration-deflagra...The penetration-deflagration coupling damage performance of rod-like reactive shaped charge pene-trator(RRSCP)impacting thick steel plates is investigated by theoretical analysis and experiments.A penetration-deflagration coupling damage model is developed to predict the penetration depth and cratering diameter.Four type of aluminum-polytetrafluoroethylene-copper(Al-PTFE-Cu)reactive liners with densities of 2.3,2.7,3.5,and 4.5 g·cm^(-3) are selected to conduct the penetration experiments.The comparison results show that model predictions are in good agreement with the experimental data.By comparing the penetration depth and cratering diameter in the inert penetration mode and the penetration-deflagration coupling mode,the influence mechanism that the penetration-induced chemical response is unfavorable to penetration but has an enhanced cratering effect is revealed.From the formation characteristics,penetration effect and penetration-induced chemical reaction be-haviors,the influence of reactive liner density on the penetration-deflagration performance is further analyzed.The results show that increasing the density of reactive liner significantly increases both the kinetic energy and length of the reactive penetrator,meanwhile effectively reduces the weakened effect of penetration-induced chemical response,resulting in an enhanced penetration capability.However,due to the decreased diameter and potential energy content of reactive penetrator,the cratering capa-bility is weakened significantly.展开更多
To enhance the overall performance of cyclotrimethylenetrinitramine(RDX),a modification strategy for RDX via in situ coordination with monometallic polydopamine(PDA)coatings(PDA-Fe,PDA-Cu,and PDA-Pb)was developed.The ...To enhance the overall performance of cyclotrimethylenetrinitramine(RDX),a modification strategy for RDX via in situ coordination with monometallic polydopamine(PDA)coatings(PDA-Fe,PDA-Cu,and PDA-Pb)was developed.The thermal properties of pristine RDX and its modified variants(RDX@PDA-Fe,RDX@PDA-Cu,RDX@PDA-Pb)were characterized using differential scanning calorimetry(DSC)and accelerating rate calorimetry(ARC).The impact sensitivity of these materials was evaluated via the characteristic drop-height method.The results demonstrate that PDA-metal metal coatings—formed through coordination between PDA and single metal ions(Fe^(3+),Cu^(2+),or Pb^(2+))—significantly enhance RDX′s thermal stability while attenuating its mechanical sensitivity.These coatings act as energy-absorbing barriers against external stimuli,effectively mitigating RDX′s sensitivity.Furthermore,they elevate RDX′s thermal stability by increasing its decomposition onset temperature and accelerating its decomposition kinetics.The monometallic coatings also catalyze RDX′s thermal decomposition and combustion,with Cu and Pb exhibiting particularly distinct catalytic effects.展开更多
An energetic binder based on hydroxyl-terminated polybutadiene(HTPB),doped with different ratios of nitrocellulose(NC)(10%,20%,30%,and 50%),was developed to study the effect of NC doping on the thermal decomposition b...An energetic binder based on hydroxyl-terminated polybutadiene(HTPB),doped with different ratios of nitrocellulose(NC)(10%,20%,30%,and 50%),was developed to study the effect of NC doping on the thermal decomposition behavior of a composite propellant(CP)comprising ammonium nitrate(AN)as an oxidizer and magnesium(Mg)as a fuel.Optimization of the propellant formulation was conducted using Chemical Equilibrium with Applications-National Aeronautics and Space Administration(CEA-NASA)software,which demonstrated an increase in specific impulse by 12.09 s when the binder contained 50%NC.Fourier-transform infrared spectroscopy(FTIR)analysis confirmed the excellent compatibility between the components,and density measurements revealed an increase of 6.4%with a higher NC content.Morphological analysis using optical microscopy showed that NC doping improved the uniformity and compactness of the surface,reduced cavities,and achieved a more homogeneous particle distribution.Differential scanning calorimetry(DSC)analysis indicated a decrease in the decomposition temperature of the propellant as the NC content increased,while kinetic studies revealed a 48.68%reduction in the activation energy when 50%NC was incorporated into the binder.These findings suggest that the addition of NC enhances combustion efficiency and improves overall propellant performance.This study highlights the potential of the new HTPB-NC energetic binder as a promising approach for advancing solid propellant technology.展开更多
In pursuit of more efficient and stable electrochemical energy storage materials,composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and...In pursuit of more efficient and stable electrochemical energy storage materials,composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and exceptional properties.Graphene oxide(GO),a two-dimensional material with an extremely high specific surface area and excellent conductivity,offers new possibilities for enhancing the electrochemical performance of metal oxides.In this work,we synthesized met-al-organic framework(MOF)and GO composites by regulating the amount of GO,and successfully prepared composites of metal oxides supported by nitrogen-doped carbon frameworks and GO through a simple one-step calcination process.Based on the electrochemical tests,the optimal amount of GO was determined.This research will provide new insights into and directions for designing and synthesizing metal oxide and graphene oxide composite materials with an ideal electro-chemical performance.展开更多
The rising concern over electromagnetic (EM) pollution is re-sponsible for the rapid progress in EM interference (EMI) shielding and EM wave absorption in the last few years, and carbon materials with a large sur-face...The rising concern over electromagnetic (EM) pollution is re-sponsible for the rapid progress in EM interference (EMI) shielding and EM wave absorption in the last few years, and carbon materials with a large sur-face area and high porosity have been investigated. Compared to other car-bon materials, biomass-derived carbon (BC) are considered efficient and eco-friendly materials for this purpose. We summarize the recent advances in BC materials for both EMI shielding and EM wave absorption. After a brief overview of the synthesis strategies of BC materials and a precise out-line of EM wave interference, strategies for improving their EMI shielding and EM wave absorption are discussed. Finally, the existing challenges and the future prospects for such materials are briefly summarized.展开更多
Continuous carbon fiber reinforced silicon carbide(C/SiC)composites are often subjected to low-velocity impacts when utilized as structural materials for thermal protection.However,research on in-plane impact damage a...Continuous carbon fiber reinforced silicon carbide(C/SiC)composites are often subjected to low-velocity impacts when utilized as structural materials for thermal protection.However,research on in-plane impact damage and multiple impact damage of C/SiC composites is limited.To investigate the in-plane impact damage behavior of C/SiC composites,a drop-weight impact test method was developed for strip samples,and these results were subsequently compared with those of C/SiC composite plates.Results show that the in-plane impact behavior of C/SiC strip samples is similar to that of C/SiC composite plates.Variation of the impact load with displacement is characterized by three stages:a nearly linear stage,a severe load drop stage,and a rebound stage where displacement occurs after the impact energy exceeds its peak value.Impact damage behavior under single and multiple impacts on 2D plain and 3D needled C/SiC composites was investigated at different impact energies and durations.Crack propagation in C/SiC composites was studied by computerized tomography(CT)technique.In the 2D plain C/SiC composite,load propagation between layers is hindered during impact,leading to delamination and 90°fiber brittle fracture.The crack length perpendicular to the impact direction increases with impact energy increases,resulting in more serious 0°fiber fracture and a larger area of fiber loss.In the 3D needled C/SiC composite,load propagates between the layers during impact through the connection of needled fibers.The fibers continue to provide substantial structural support,with notable instances of fiber pull-off and debonding.Consequently,the impact resistance is superior to that of 2D plain C/SiC composite.When the 3D needled C/SiC composite undergoes two successive impacts of 1.5 J,the energy absorption efficiency of the second impact is significantly lower,accompanied by a smaller impact displacement.Moreover,the total energy absorption efficiency of these two impacts of 1.5 J is lower than that of a single 3.0 J impact.展开更多
Aseries of [(Fe_(0.6)Co_(0.2)Ni_(0.2))_(0.75-0.03x)B_(0.2)Si_(0.05+0.03x)]_(96)Nb_(4) amorphous alloy composite coatings were prepared by adjusting the silicon content(x=0,1,2,3,4,5,and 6)and their microstructures and...Aseries of [(Fe_(0.6)Co_(0.2)Ni_(0.2))_(0.75-0.03x)B_(0.2)Si_(0.05+0.03x)]_(96)Nb_(4) amorphous alloy composite coatings were prepared by adjusting the silicon content(x=0,1,2,3,4,5,and 6)and their microstructures and tribological properties were investigated by laser cladding technique.Additionally,the effect of Si on the glass forming ability(GFA)of the layers was understood.Results show that an appropriate Si content can refine the microstructure of the FeCoNiBSiNb laser cladding layers and improve the mechanical and tribological properties.The hardness of the coating layer increases monotonically with the Si content.At the Si content of 4.8at%(x=0),the coating layer exhibits a relatively low hardness(734.2HV 0.1).Conversely,at the silicon content of 13.44at%(x=3),the coating layer exhibits the highest hardness(1106HV 0.1).The non-crystalline content and tensile strength exhibit an initial increase,followed by a subsequent decrease.At x=2,the coating exhibits its maximum fracture strength(2880 MPa).However,when x>2,the fracture strength of the coating decreases with an increase in x.Conversely,with an increase in Si content,the wear volume loss initially decreases and then increases.At a Si content of 10.56at%(x=2),the coating exhibits the highest non-crystalline content(42%),the highest tensile strength(2880 MPa),and the most favorable dry friction performance.展开更多
Cs_(x)WO_(3)/TiO_(2) composites with full-spectrum catalytic activity were prepared by solvothermal reaction.The composites were characterized using X-ray diffraction(XRD)analysis,scanning electron microscopy(SEM),tra...Cs_(x)WO_(3)/TiO_(2) composites with full-spectrum catalytic activity were prepared by solvothermal reaction.The composites were characterized using X-ray diffraction(XRD)analysis,scanning electron microscopy(SEM),transmission electron microscopy(TEM),specific surface area testing,X-ray photoelectron spectroscopy(XPS),and UV-Vis diffuse reflectance spectra(UV-Vis DRS).Cs_(x)WO_(3) and TiO_(2) were uniformly bonded together in the compos-ites.The heterojunction structure was formed.The band gap was reduced from 2.75 to 2.65 eV.The photocatalytic property of Cs_(x)WO_(3)/TiO_(2)was demonstrated by the degradation rates of 20 mg·L^(-1) methylene blue dye,which were 99.7%,91.4%,and 70.7%under irradiation from a 300 W high-pressure mercury lamp,a 500 W xenon lamp,and a 400 W infrared lamp,respectively.After five cycles of photocatalytic degradation,the composite photocatalyst still showed a degradation efficiency of 87.6%.This indicates that Cs_(x)WO_(3)/TiO_(2) has good photocatalytic degradability and cyclic stability.The photocatalytic mechanism of Cs_(x)WO_(3)/TiO_(2)was investigated.The trapping experiments of the active species showed that the main active substances were the empty hole(h+)and hydroxyl radical(·OH).展开更多
The boundness and compactness of products of multiplication,composition and differentiation on weighted Bergman spaces in the unit ball are studied.We define the differentiation operator on the space of holomorphic fu...The boundness and compactness of products of multiplication,composition and differentiation on weighted Bergman spaces in the unit ball are studied.We define the differentiation operator on the space of holomorphic functions in the unit ball by radial derivative.Then we extend the Sharma's results.展开更多
Nitrogen doping in chemical vapor deposition-derived ultrananocrystalline diamond(UNCD)films in-creases the electronic conductivity,yet its microstructural effects on electron transport are insufficiently understood.W...Nitrogen doping in chemical vapor deposition-derived ultrananocrystalline diamond(UNCD)films in-creases the electronic conductivity,yet its microstructural effects on electron transport are insufficiently understood.We investigated the formation of nitrogen-induced diaph-ite structures(hybrid diamond-graphite phases)and their role in changing the conductivity.Nitrogen doping in a hy-drogen-rich plasma environment promotes the emergence of unique sp^(3)-sp^(2)bonding interfaces,where diamond grains are covalently integrated with graphitic domains,facilitating a structure-driven electronic transition.High-resolution transmis-sion electron microscopy and selected area electron diffraction reveal five-fold,six-fold and twelve-fold symmetries,along with an atypical{200}crystallographic reflection,confirming diaphite formation in 5%and 10%N-doped UNCD films,while high-er doping levels(15%and 20%)result in extensive graphitization.Raman spectroscopy tracks the evolution of sp^(2)bonding with increasing nitrogen content,while atomic force microscopy and X-ray diffraction indicate a consistent diamond grain size of~8 nm.Cryogenic electronic transport measurements reveal a conductivity increase from 8.72 to 708 S/cm as the nitrogen dop-ing level increases from 5%to 20%,which is attributed to defect-mediated carrier transport and 3D weak localization.The res-ulting conductivity is three orders of magnitude higher than previously reported.These findings establish a direct correlation between diaphite structural polymorphism and tunable electronic properties in nitrogen-doped UNCD films,offering new ways for defect-engineering diamond-based electronic materials.展开更多
Metal phosphides have been studied as prospective anode materials for sodium-ion batteries(SIBs)due to their higher specific capacity compared to other anode materials.However,rapid capacity decay and limited cycle li...Metal phosphides have been studied as prospective anode materials for sodium-ion batteries(SIBs)due to their higher specific capacity compared to other anode materials.However,rapid capacity decay and limited cycle life caused by volume expansion and low electrical conductivity of phosphides in SIBs remain still unsolved.To address these issues,GeP_(3) was first prepared by high-energy ball milling,and then Ketjen black(KB)was introduced to synthesize composite GeP_(3)/KB anode materials under controlled milling speed and time by a secondary ball milling process.During the ball milling process,GeP_(3) and KB form strong chemical bonds,resulting in a closely bonded composite.Consequently,the GeP_(3)/KB anodes was demonstrated excellent sodium storage performance,achieving a high reversible capacity of 933.41 mAh·g^(–1) at a current density of 0.05 A·g^(–1) for a special formula of GeP_(3)/KB-600-40 sample prepared at ball milling speed of 600 r/min for 40 h.Even at a high current density of 2 A·g^(–1) over 200 cycles,the capacity remains 314.52 mAh·g^(–1) with a retention rate of 66.6%.In conclusion,this work successfully prepares GeP_(3)/KB anode-carbon composite for electrodes by high-energy ball milling,which can restrict electrode volume expansion,enhance capacity,and improve cycle stability of SIBs.展开更多
As a negative electrode material for lithium-ion batteries,silicon monoxide(SiO)suffers from dramatic volume changes during cycling,causing excessive stress within the electrode and resulting in electrode deformation ...As a negative electrode material for lithium-ion batteries,silicon monoxide(SiO)suffers from dramatic volume changes during cycling,causing excessive stress within the electrode and resulting in electrode deformation and fragmentation.This ultimately leads to a decrease in cell capacity.The trends of volume expansion and capacity change of the SiO/graphite(SiO/C)composite electrode during cycling were investigated via in situ expansion monitoring.First,a series of expansion test schemes were designed,and the linear relationship between negative electrode expansion and cell capacity degradation was quantitatively analyzed.Then,the effects of different initial pressures on the long-term cycling performance of the cell were evaluated.Finally,the mechanism of their effects was analyzed by scanning electron microscope.The results show that after 50 cycles,the cell capacity decreases from 2.556 mAh to 1.689 mAh,with a capacity retention ratio(CRR)of only 66.08%.A linear relationship between the capacity retention ratio and thickness expansion was found.Electrochemical measurements and scanning electron microscope images demonstrate that intense stress inhibits the lithiation of the negative electrode and that the electrode is more susceptible to irreversible damage during cycling.Overall,these results reveal the relationship between the cycling performance of SiO and the internal pressure of the electrode from a macroscopic point of view,which provides some reference for the application of SiO/C composite electrodes in lithium-ion batteries.展开更多
基金This work was supported by the Fundamental Research Funds for the Central Universities(No.30918011324).
文摘The effects of magnesium/polytetrafluoroethylene(Mg/PTFE)pyrotechnic compositions on the coupled flow field and reignition mechanism are important aspects governing the perfommance and range of base bleed projectiles(BBPs).Owing to a decrease in pressure and temperature when the BBP leaves the muzzle,rapid depressurization occurs,which extinguishes the base bleed propellant.The Mg/PTFE py-rotechnic composition pressed in the igniter of the base bleed unit(BBU)provides additional energy to the BBU via a chemical reaction.Thus,the extinguished base bleed propellant is reignited under the effect of high-temperature combustion gas jets from the igniter.In this study,a numerical analysis is conducted to evaluate the effects of PTFE and Mg granularity as well as Mg/PTFE pyrotechnic compo-sitions.Owing to the rapid depressurization,the temperature and pressure was found to decrease fordifferent Mg/PIFE pyrotechnic compositions.However,the depressurization time increased as the PTFE granularity increased,the Mg granularity decreased,and the Mg content increased.When the pressure in the combustion chamber of the BBU decreased to the atmospheric pressure,the combustion gas jets from the igniter expand upstream(rather than downstream).However,these combustion gas jets exhibit different axial and radial expansion characteristics depending on the pyrotechnic compositions used,The results show that the reignition delay time,ta,of the base bleed propellant was 377.608,94.27,387.243,523.966,and 221.094 ms for cases A-E,respectively.Therefore,it was concluded that the Mg/PTFE pyrotechnic composition of case B was the most beneficial for the reignition of the base bleed propellant,with the earliest addition of energy and mass to the BBP.
文摘Uranium ore is an essential material in the preparation of nuclear fuel for civilian and military uses.Uranium deposits are also important sources of energy for countries which depend heavily on nuclear power(e.g.France).
基金Project (FANEDD 200545) supported by the Foundation for the Author of National Excellent Doctoral Dissertation of China Project (50408019) supported by the National Natural Science Foundation of China Project (2008BAJ12B03) supported by National Key Project of Scientific and Technical Supporting Programs of China
文摘Source apportionment of particulate matters with aerodynamic diameter less than 10 μm （PM10） was conducted in the suburban area of Changsha, China. PM10 samples for 24 h collected with TEOM 1400a and ACCU system in July and October 2008 were chemically analyzed by the wavelength dispersive X-ray fluorescence （WD-XRF）. Source appointment was implemented by the principal component analysis/absolute principal component analysis （PCA/APCA） to identify the possible sources and to quantify the contributions of the sources to PM10. Results show that as the PM10 concentration is increased from （85.6±43.7） μg/m3 in July 2008 to （107.6±35.7） μg/m^3 in October 2008, the concentrations of the anthropogenic elements （P, S, C1, K, Mn, Ni, Cu, Zn, and Pb） are basically increased but concentrations of the natural elements （Na, Mg, Al, Si, Ca, Ti, and Fe） are essentially decreased. Six main sources of PM10 are identified in the suburban of Changsha, China： soil dust, secondary aerosols, domestic oil combustion, waste incineration, traffic emission, and industrial emission contribute 57.7%, 24.0%, 9.8%, 5.0%, 2.0%, and 1.5%, respectively. Soil dust and secondary aerosols are the two major sources of particulate air pollution in suburban area of Changsha, China, so effective measures should be taken to control these two particulate pollutants.
文摘Upper atmosphere composition data were obtained for the last half year with a quadruple mass spectrometer on board spacecraft "SZ-2" launched on 10 Jan uary 2001. Based on the analysis of these data, the variations of atmospheric compositions in solar and geomagnetic quiet conditions are reported first, then a detailed discussion on the atmospheric composition variations under the so lar and geomagnetic disturbed conditions is given. The results show that near the altitude of 400 km the variations of main atmospheric compositions corre sponding to solar disturbances are more remarkable in the sunlit area than in the shade area. On the contrary, in geomagnetic disturbance events the corre sponding variations are more obvious in the shade area, an evident increase of N2 density at relatively higher latitudes was observed.
基金Project(51302206)supported by the National Natural Science Foundation of ChinaProject(2013JK0925)supported by Shaanxi Provincial Department of Education,China+1 种基金Project(SKLSP201308)supported by the State Key Laboratory of Solidification Processing in Northwestern Polytechnical University,ChinaProject supported by the State Scholarship Fund,China
文摘The phase compositions and properties of Ti3SiC2-based composites with SiC addition of 5%-30% in mass fraction fabricated by in-situ reaction and hot pressing sintering were studied. SiC addition effectively prevented TiC synthesis but facilitated SiC synthesis. The Ti3SiC2/Ti C-SiC composite had better oxidation resistance when SiC added quantity reached 20% but poorer oxidation resistance with SiC addition under 15% than Ti3SiC2/TiC composite at higher temperatures. There were more than half of the original SiC and a few Ti3SiC2 remaining in Ti3SiC2/Ti C-SiC with 20% SiC addition, but all constituents in Ti3Si2/TiC composite were oxidized after 12 h in air at 1500 °C. The oxidation scale thickness of TS30, 1505.78 μm, was near a half of that of T,2715 μm, at 1500 °C for 20 h. Ti3SiC2/Ti C composite had a flexural strength of 474 MPa, which was surpassed by Ti3SiC2/TiC-SiC composites when SiC added amount reached 15%. The strength reached the peak of 518 MPa at 20% SiC added amount.
文摘The Lesser Himalaya in central Nepal consists of greenschist\|facies metasedimentary rocks, which are overthrust by the amphibolite\|facies rocks of the Higher Himalaya along the Upper Main Central Thrust (UMCT). Despite a number of works on metamorphism of the MCT zone and the Higher Himalaya, the low\|grade metamorphic rocks to the south of the MCT zone have not been studied yet.In the present study, an attempt was made to constrain the metamorphic events and thermal structure of the whole Lesser Himalaya by means of white mica (Ms) compositions. About 600Ms grains in 48 metapelitic samples from the Lesser Himalaya were analysed by the EPMA. Compositional zoning in individual Ms grains was checked by means of X\|ray compositional mapping. There exist wide intersample, intrasample and within grain compositional variations in Ms in the samples from the Lesser Himalaya. Sheared Ms phenocrysts in pegmatites and gneisses have compositions very close to that of the ideal muscovite. Detrital Ms show wide variation in phengite content, most of which are poor in phengite content, and are most probably derived from older higher\|grade metamorphic rocks.
基金Supported by the National Natural Science Foundation Project(31472145)
文摘Wild native Elymus(Elymus dahuricus)is one of the most important and valuable forage grass on Qinghai-Tibetan Plateau(QTP)pasture of China.It mainly distributes above sea-level of 1700 to 3000 m on the QTP.The objective of this study was to investigate how the nutritive composition of Elymus responsed to the changes of altitude in local environments.Two test sites located at Minghe and Huangzhong counties,in which four sampling plots were arranged with sea levels of 1714,1872,2097 and 2185 m in Minhe County,while other four in Huangzhong County were with sea-level of 2560,2613,2668 and 2775 m.The whole plants of Elymus during anthesis stage were collected from all the plots for determining the indexes of crude protein(CP),crude fat(CF),neutral detergent fiber(NDF),acid detergent fiber(ADF),crude ash(ASH),calcium(Ca)and phosphorus(P).The results showed that the content of CP,crude ash and Ca changed irregularly corresponding to the altitude in the two counties,but significant higher with CP(1.09%),Ash(0.33%)and Ca(0.34%)in the low altitude areas(1714-2185 m)than those in the high altitude areas.NDF and ADF in the low altitude areas were significantly lower by 5.35% and 2.61% compared with those in the high altitude areas.There was no significant difference of CF as well as P in plant from different altitudes.Comprehensive evaluation revealed that superior nutritional composition of Elymus dahuricus presented at the sampling plots of altitude of 1714 m in Minhe County.
基金supported by the National Natural Science Foundation of China(Grant No.12172052)the Foundation of State Key Laboratory of Explosion Science and Safety Protection(Grant No.QKKT24-02).
文摘The penetration-deflagration coupling damage performance of rod-like reactive shaped charge pene-trator(RRSCP)impacting thick steel plates is investigated by theoretical analysis and experiments.A penetration-deflagration coupling damage model is developed to predict the penetration depth and cratering diameter.Four type of aluminum-polytetrafluoroethylene-copper(Al-PTFE-Cu)reactive liners with densities of 2.3,2.7,3.5,and 4.5 g·cm^(-3) are selected to conduct the penetration experiments.The comparison results show that model predictions are in good agreement with the experimental data.By comparing the penetration depth and cratering diameter in the inert penetration mode and the penetration-deflagration coupling mode,the influence mechanism that the penetration-induced chemical response is unfavorable to penetration but has an enhanced cratering effect is revealed.From the formation characteristics,penetration effect and penetration-induced chemical reaction be-haviors,the influence of reactive liner density on the penetration-deflagration performance is further analyzed.The results show that increasing the density of reactive liner significantly increases both the kinetic energy and length of the reactive penetrator,meanwhile effectively reduces the weakened effect of penetration-induced chemical response,resulting in an enhanced penetration capability.However,due to the decreased diameter and potential energy content of reactive penetrator,the cratering capa-bility is weakened significantly.
基金National Natural Science Foundation of China(No.22405249)Open Project of Key Laboratory of Rubber Research Institute,Chinese Academy of Tropical Agricultural Science in 2025(No.RRI-KLOF202402)。
文摘To enhance the overall performance of cyclotrimethylenetrinitramine(RDX),a modification strategy for RDX via in situ coordination with monometallic polydopamine(PDA)coatings(PDA-Fe,PDA-Cu,and PDA-Pb)was developed.The thermal properties of pristine RDX and its modified variants(RDX@PDA-Fe,RDX@PDA-Cu,RDX@PDA-Pb)were characterized using differential scanning calorimetry(DSC)and accelerating rate calorimetry(ARC).The impact sensitivity of these materials was evaluated via the characteristic drop-height method.The results demonstrate that PDA-metal metal coatings—formed through coordination between PDA and single metal ions(Fe^(3+),Cu^(2+),or Pb^(2+))—significantly enhance RDX′s thermal stability while attenuating its mechanical sensitivity.These coatings act as energy-absorbing barriers against external stimuli,effectively mitigating RDX′s sensitivity.Furthermore,they elevate RDX′s thermal stability by increasing its decomposition onset temperature and accelerating its decomposition kinetics.The monometallic coatings also catalyze RDX′s thermal decomposition and combustion,with Cu and Pb exhibiting particularly distinct catalytic effects.
文摘An energetic binder based on hydroxyl-terminated polybutadiene(HTPB),doped with different ratios of nitrocellulose(NC)(10%,20%,30%,and 50%),was developed to study the effect of NC doping on the thermal decomposition behavior of a composite propellant(CP)comprising ammonium nitrate(AN)as an oxidizer and magnesium(Mg)as a fuel.Optimization of the propellant formulation was conducted using Chemical Equilibrium with Applications-National Aeronautics and Space Administration(CEA-NASA)software,which demonstrated an increase in specific impulse by 12.09 s when the binder contained 50%NC.Fourier-transform infrared spectroscopy(FTIR)analysis confirmed the excellent compatibility between the components,and density measurements revealed an increase of 6.4%with a higher NC content.Morphological analysis using optical microscopy showed that NC doping improved the uniformity and compactness of the surface,reduced cavities,and achieved a more homogeneous particle distribution.Differential scanning calorimetry(DSC)analysis indicated a decrease in the decomposition temperature of the propellant as the NC content increased,while kinetic studies revealed a 48.68%reduction in the activation energy when 50%NC was incorporated into the binder.These findings suggest that the addition of NC enhances combustion efficiency and improves overall propellant performance.This study highlights the potential of the new HTPB-NC energetic binder as a promising approach for advancing solid propellant technology.
基金supported by the National Natural Science Foundation of China(51971157)Shenzhen Science and Technology Program(JCYJ20210324115412035,JCYJ202103-24123202008,JCYJ20210324122803009 and ZDS-YS20210813095534001)Guangdong Foundation for Basic and Applied Basic Research Program(2021A1515110880).
文摘In pursuit of more efficient and stable electrochemical energy storage materials,composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and exceptional properties.Graphene oxide(GO),a two-dimensional material with an extremely high specific surface area and excellent conductivity,offers new possibilities for enhancing the electrochemical performance of metal oxides.In this work,we synthesized met-al-organic framework(MOF)and GO composites by regulating the amount of GO,and successfully prepared composites of metal oxides supported by nitrogen-doped carbon frameworks and GO through a simple one-step calcination process.Based on the electrochemical tests,the optimal amount of GO was determined.This research will provide new insights into and directions for designing and synthesizing metal oxide and graphene oxide composite materials with an ideal electro-chemical performance.
基金Anusandhan National Research Foundation (ANRF), Department of Science & Technology (DST), New Delhi, India under Ramanujan award (SB/S2/RJN-159/2017)。
文摘The rising concern over electromagnetic (EM) pollution is re-sponsible for the rapid progress in EM interference (EMI) shielding and EM wave absorption in the last few years, and carbon materials with a large sur-face area and high porosity have been investigated. Compared to other car-bon materials, biomass-derived carbon (BC) are considered efficient and eco-friendly materials for this purpose. We summarize the recent advances in BC materials for both EMI shielding and EM wave absorption. After a brief overview of the synthesis strategies of BC materials and a precise out-line of EM wave interference, strategies for improving their EMI shielding and EM wave absorption are discussed. Finally, the existing challenges and the future prospects for such materials are briefly summarized.
基金Aeronautical Science Foundation of China(2021Z057053001)。
文摘Continuous carbon fiber reinforced silicon carbide(C/SiC)composites are often subjected to low-velocity impacts when utilized as structural materials for thermal protection.However,research on in-plane impact damage and multiple impact damage of C/SiC composites is limited.To investigate the in-plane impact damage behavior of C/SiC composites,a drop-weight impact test method was developed for strip samples,and these results were subsequently compared with those of C/SiC composite plates.Results show that the in-plane impact behavior of C/SiC strip samples is similar to that of C/SiC composite plates.Variation of the impact load with displacement is characterized by three stages:a nearly linear stage,a severe load drop stage,and a rebound stage where displacement occurs after the impact energy exceeds its peak value.Impact damage behavior under single and multiple impacts on 2D plain and 3D needled C/SiC composites was investigated at different impact energies and durations.Crack propagation in C/SiC composites was studied by computerized tomography(CT)technique.In the 2D plain C/SiC composite,load propagation between layers is hindered during impact,leading to delamination and 90°fiber brittle fracture.The crack length perpendicular to the impact direction increases with impact energy increases,resulting in more serious 0°fiber fracture and a larger area of fiber loss.In the 3D needled C/SiC composite,load propagates between the layers during impact through the connection of needled fibers.The fibers continue to provide substantial structural support,with notable instances of fiber pull-off and debonding.Consequently,the impact resistance is superior to that of 2D plain C/SiC composite.When the 3D needled C/SiC composite undergoes two successive impacts of 1.5 J,the energy absorption efficiency of the second impact is significantly lower,accompanied by a smaller impact displacement.Moreover,the total energy absorption efficiency of these two impacts of 1.5 J is lower than that of a single 3.0 J impact.
文摘Aseries of [(Fe_(0.6)Co_(0.2)Ni_(0.2))_(0.75-0.03x)B_(0.2)Si_(0.05+0.03x)]_(96)Nb_(4) amorphous alloy composite coatings were prepared by adjusting the silicon content(x=0,1,2,3,4,5,and 6)and their microstructures and tribological properties were investigated by laser cladding technique.Additionally,the effect of Si on the glass forming ability(GFA)of the layers was understood.Results show that an appropriate Si content can refine the microstructure of the FeCoNiBSiNb laser cladding layers and improve the mechanical and tribological properties.The hardness of the coating layer increases monotonically with the Si content.At the Si content of 4.8at%(x=0),the coating layer exhibits a relatively low hardness(734.2HV 0.1).Conversely,at the silicon content of 13.44at%(x=3),the coating layer exhibits the highest hardness(1106HV 0.1).The non-crystalline content and tensile strength exhibit an initial increase,followed by a subsequent decrease.At x=2,the coating exhibits its maximum fracture strength(2880 MPa).However,when x>2,the fracture strength of the coating decreases with an increase in x.Conversely,with an increase in Si content,the wear volume loss initially decreases and then increases.At a Si content of 10.56at%(x=2),the coating exhibits the highest non-crystalline content(42%),the highest tensile strength(2880 MPa),and the most favorable dry friction performance.
文摘Cs_(x)WO_(3)/TiO_(2) composites with full-spectrum catalytic activity were prepared by solvothermal reaction.The composites were characterized using X-ray diffraction(XRD)analysis,scanning electron microscopy(SEM),transmission electron microscopy(TEM),specific surface area testing,X-ray photoelectron spectroscopy(XPS),and UV-Vis diffuse reflectance spectra(UV-Vis DRS).Cs_(x)WO_(3) and TiO_(2) were uniformly bonded together in the compos-ites.The heterojunction structure was formed.The band gap was reduced from 2.75 to 2.65 eV.The photocatalytic property of Cs_(x)WO_(3)/TiO_(2)was demonstrated by the degradation rates of 20 mg·L^(-1) methylene blue dye,which were 99.7%,91.4%,and 70.7%under irradiation from a 300 W high-pressure mercury lamp,a 500 W xenon lamp,and a 400 W infrared lamp,respectively.After five cycles of photocatalytic degradation,the composite photocatalyst still showed a degradation efficiency of 87.6%.This indicates that Cs_(x)WO_(3)/TiO_(2) has good photocatalytic degradability and cyclic stability.The photocatalytic mechanism of Cs_(x)WO_(3)/TiO_(2)was investigated.The trapping experiments of the active species showed that the main active substances were the empty hole(h+)and hydroxyl radical(·OH).
基金Supported by Natural Science Foundation of Guangdong Province in China(2018KTSCX161)。
文摘The boundness and compactness of products of multiplication,composition and differentiation on weighted Bergman spaces in the unit ball are studied.We define the differentiation operator on the space of holomorphic functions in the unit ball by radial derivative.Then we extend the Sharma's results.
文摘Nitrogen doping in chemical vapor deposition-derived ultrananocrystalline diamond(UNCD)films in-creases the electronic conductivity,yet its microstructural effects on electron transport are insufficiently understood.We investigated the formation of nitrogen-induced diaph-ite structures(hybrid diamond-graphite phases)and their role in changing the conductivity.Nitrogen doping in a hy-drogen-rich plasma environment promotes the emergence of unique sp^(3)-sp^(2)bonding interfaces,where diamond grains are covalently integrated with graphitic domains,facilitating a structure-driven electronic transition.High-resolution transmis-sion electron microscopy and selected area electron diffraction reveal five-fold,six-fold and twelve-fold symmetries,along with an atypical{200}crystallographic reflection,confirming diaphite formation in 5%and 10%N-doped UNCD films,while high-er doping levels(15%and 20%)result in extensive graphitization.Raman spectroscopy tracks the evolution of sp^(2)bonding with increasing nitrogen content,while atomic force microscopy and X-ray diffraction indicate a consistent diamond grain size of~8 nm.Cryogenic electronic transport measurements reveal a conductivity increase from 8.72 to 708 S/cm as the nitrogen dop-ing level increases from 5%to 20%,which is attributed to defect-mediated carrier transport and 3D weak localization.The res-ulting conductivity is three orders of magnitude higher than previously reported.These findings establish a direct correlation between diaphite structural polymorphism and tunable electronic properties in nitrogen-doped UNCD films,offering new ways for defect-engineering diamond-based electronic materials.
基金National Natural Science Foundation of China Young Scientist Fund(22105120)Shaanxi Province Qin Chuangyuan“Scientist+Engineer”Team Construction Project(2024QCY-KXJ-127)。
文摘Metal phosphides have been studied as prospective anode materials for sodium-ion batteries(SIBs)due to their higher specific capacity compared to other anode materials.However,rapid capacity decay and limited cycle life caused by volume expansion and low electrical conductivity of phosphides in SIBs remain still unsolved.To address these issues,GeP_(3) was first prepared by high-energy ball milling,and then Ketjen black(KB)was introduced to synthesize composite GeP_(3)/KB anode materials under controlled milling speed and time by a secondary ball milling process.During the ball milling process,GeP_(3) and KB form strong chemical bonds,resulting in a closely bonded composite.Consequently,the GeP_(3)/KB anodes was demonstrated excellent sodium storage performance,achieving a high reversible capacity of 933.41 mAh·g^(–1) at a current density of 0.05 A·g^(–1) for a special formula of GeP_(3)/KB-600-40 sample prepared at ball milling speed of 600 r/min for 40 h.Even at a high current density of 2 A·g^(–1) over 200 cycles,the capacity remains 314.52 mAh·g^(–1) with a retention rate of 66.6%.In conclusion,this work successfully prepares GeP_(3)/KB anode-carbon composite for electrodes by high-energy ball milling,which can restrict electrode volume expansion,enhance capacity,and improve cycle stability of SIBs.
基金supported by the Fundamental Research Funds for the Central Universities(WK2090000055)Anhui Provincial Natural Science Foundation of China(2308085QG231).
文摘As a negative electrode material for lithium-ion batteries,silicon monoxide(SiO)suffers from dramatic volume changes during cycling,causing excessive stress within the electrode and resulting in electrode deformation and fragmentation.This ultimately leads to a decrease in cell capacity.The trends of volume expansion and capacity change of the SiO/graphite(SiO/C)composite electrode during cycling were investigated via in situ expansion monitoring.First,a series of expansion test schemes were designed,and the linear relationship between negative electrode expansion and cell capacity degradation was quantitatively analyzed.Then,the effects of different initial pressures on the long-term cycling performance of the cell were evaluated.Finally,the mechanism of their effects was analyzed by scanning electron microscope.The results show that after 50 cycles,the cell capacity decreases from 2.556 mAh to 1.689 mAh,with a capacity retention ratio(CRR)of only 66.08%.A linear relationship between the capacity retention ratio and thickness expansion was found.Electrochemical measurements and scanning electron microscope images demonstrate that intense stress inhibits the lithiation of the negative electrode and that the electrode is more susceptible to irreversible damage during cycling.Overall,these results reveal the relationship between the cycling performance of SiO and the internal pressure of the electrode from a macroscopic point of view,which provides some reference for the application of SiO/C composite electrodes in lithium-ion batteries.
