In some worldwide hard coal basins recovery of methane from virgin coal beds is difficult. In general,mentioned difficulties are related to geo-mechanical, petrographical and physical-chemical properties of coals in q...In some worldwide hard coal basins recovery of methane from virgin coal beds is difficult. In general,mentioned difficulties are related to geo-mechanical, petrographical and physical-chemical properties of coals in question, occurring for example in the Bowen Basin(Australia) or the Upper Silesian Coal Basin(Poland). Among numerous properties and parameters, the following are very essential: susceptibility of coal beds to deformation connected with coal stress state change and contemporary shrinkage of the coal matrix during methane desorption. Those adverse geo-mechanical and physical-chemical effects are accompanied by essential change of the porous coal structure, which under these disadvantageous conditions is very complex. This study aims to show difficulties, which occur in phase of recognition of the methane-reach coal deposit. Volume absorbed methane(not surface adsorbed) in sub-micropores having minimal size comparable with gas molecule diameter must possess energy allowing separation of the nodes and methane release to micropores.展开更多
Coal bed methane （CBM） has a huge potential to be purified to relieve the shortage of natural gas meanwhile to weaken the greenhouse effect. This paper proposed an optimal design strategy for CBM to obtain an integr...Coal bed methane （CBM） has a huge potential to be purified to relieve the shortage of natural gas meanwhile to weaken the greenhouse effect. This paper proposed an optimal design strategy for CBM to obtain an integrated process configuration consisting of three each single separation units, membrane, pressure swing absorption, and cryogenics. A superstructure model was established including all possible network configurations which were solved by MINLP. The design strategy optimized the separation unit configuration and operating conditions to satisfy the target of minimum total annual process cost. An example was presented for the separation of CH4/N2 mixtures in coal bed methane （CBM） treatment. The key operation parameters were also studied and they showed the influence to process configurations.展开更多
The geothermal fields of coal-bearing strata have become a key topic in geological research into coal and coal bed methane(CBM).Based on temperature data from 135 boreholes that penetrate the Upper Permian coal-bearin...The geothermal fields of coal-bearing strata have become a key topic in geological research into coal and coal bed methane(CBM).Based on temperature data from 135 boreholes that penetrate the Upper Permian coal-bearing strata in the Bide-Santang basin,western Guizhou,the precisions of geothermal predictions made using a geothermal gradient model and a gray sequence GM(1,1)model are analyzed and compared.The results indicate that the gray sequence GM(1,1)model is more appropriate for the prediction of geothermal fields.The GM(1,1)model is used to predict the geothermal field at three levels with depths of 500,1000,and 1500 m,as well as within the No.6,No.16,and No.27 coal seams.The results indicate that the geotemperatures of the 500 m depth level are between 21.0 and 30.0°C,indicating no heat damage;the geotemperatures of the 1000 m depth level are between 29.4 and 44.7°C,indicating the first level of heat damage;and the geotemperatures of the 1500 m depth level are between35.6 and 63.4°C,indicating the second level of heat damage.The CBM contents are positively correlated with the geotemperatures of the coal seams.The target area for CBM development is identified.展开更多
Coal bed methane has been considered as an important energy resource.One major difficulty of purifying coal bed methane comes from the similar physical properties of CH_4 and N_2.The ZIF-8/water-glycol slurry was used...Coal bed methane has been considered as an important energy resource.One major difficulty of purifying coal bed methane comes from the similar physical properties of CH_4 and N_2.The ZIF-8/water-glycol slurry was used as a medium to separate coal bed methane by fluidifying the solid adsorbent material.The sorption equilibrium experiment of binary mixture(CH_4/N_2)and slurry was conducted.The selectivity of CH_4 to N_2 is within the range of 2-6,which proved the feasibility of the slurry separation method.The modified Langmuir equation was used to describe the gas-slurry phase equilibrium behavior,and the calculated results were in good agreement with the experimental data.A continuous absorption-adsorption and desorption process on the separation of CH_4/N_2 in slurry is proposed and its mathematical model is also developed.Sensitivity analysis is conducted to determine the operation conditions and the energy performance of the proposed process was also evaluated.Feed gas contains 30 mol%of methane and the methane concentration in product gas is 95.46 mol%with the methane recovery ratio of 90.74%.The total energy consumption for per unit volume of product gas is determined as 1.846 kWh Nm^(-3).Experimental results and process simulation provide basic data for the design and operation of pilot and industrial plant.展开更多
The coal bed methane content(CBMC)in the west mining area of Jincheng coalfield,southeastern Qjnshui Basin,is studied based on seismic data and well-logs together with laboratory measurements.The results show that the...The coal bed methane content(CBMC)in the west mining area of Jincheng coalfield,southeastern Qjnshui Basin,is studied based on seismic data and well-logs together with laboratory measurements.The results show that the Shuey approximation has better adaptability according to the Zoeppritz equation result;the designed fold number for an ordinary seismic data is sufficient for post-stack data but insufficient for pre-stack data regarding the signal to noise ratio(SNR).Therefore a larger grid analysis was created in order to improve the SNR.The velocity field created by logging is better than that created by stack velocity in both accuracy and effectiveness.A reasonable distribution of the amplitude versus offset(AVO)attributes can be facilitated by taking the AVO response from logging as a standard for calibrating the amplitude distribution.Some AVO attributes have a close relationship with CBMC.The worst attribute is polarization magnitude,for which the correlation coefficient is 0.308;and the best attribute is the polarization product from intercept,of which the correlation coefficient is-0.8136.CBMC predicted by AVO attributes is better overall than that predicted by direct interpolation of CBMC;the validation error of the former is 14.47%,which is lower than that of the latter 23.30%.CBMC of this area ranges from2.5 m^3/t to 22 m^3/t.Most CBMC in the syncline is over 10m^3/t,but it is below 10m^3/t in the anticline;on the whole,CBMC in the syncline is higher than that in anticline.展开更多
Coalbed methane(CBM)is an important unconventional natural gas.Exploitation of multilayered CBM reservoir is still facing the challenge of low production rate.Radial borehole fracturing,which integrates radial jet dri...Coalbed methane(CBM)is an important unconventional natural gas.Exploitation of multilayered CBM reservoir is still facing the challenge of low production rate.Radial borehole fracturing,which integrates radial jet drilling and hydraulic fracturing,is expected to create complex fracture networks in multilayers and enhance CBM recovery.The main purpose of this paper is to investigate the mechanisms and efficacy of radial borehole fracturing in increasing CBM production in multiple layers.First,a two-phase flow and multi-scale 3 D fracture network including radial laterals,hydraulic fractures and face/butt cleats model is established,and embedded discrete fracture model(EDFM)is applied to handle the complex fracture networks.Then,effects of natural-fracture nonuniform distribution are investigated to show the advantages of targeted stimulation for radial borehole fracturing.Finally,two field CBM wells located in eastern Yunnan-western Guizhou,China were presented to illuminate the stimulation efficiency by radial borehole fracturing.The results indicated that compared with vertical well fracturing,radial borehole fracturing can achieve higher gas/water daily production rate and cumulative gas/water production,approximately 2 times higher.Targeted communications to cleats and sweet spots and flexibility in designing radial borehole parameters in different layers so as to increase fracture-network complexity and connectivity are the major reasons for production enhancement of radial borehole fracturing.Furthermore,the integration of geology-engineering is vital for the decision of radial borehole fracturing designing scheme.The key findings of this paper could provide useful insights towards understanding the capability of radial borehole fracturing in developing CBM and coal-measure gas in multiple-thin layers.展开更多
Based on long-term dynamic tracing of dissolved inorganic carbon(DIC)and stable carbon isotope(δ13CDIC)in produced water from 20 coalbed methane(CBM)wells in western Guizhou,the spatial-temporal dynamic variations of...Based on long-term dynamic tracing of dissolved inorganic carbon(DIC)and stable carbon isotope(δ13CDIC)in produced water from 20 coalbed methane(CBM)wells in western Guizhou,the spatial-temporal dynamic variations ofδ13CDIC of the GP well group produced in multi-layer commingled manner were analyzed,and the relationship between the value ofδ13CDIC and CBM productivity was examined.The produced water samples of typical wells in the GP well group were amplified and sequenced using 16S rDNA,and a geological response model ofδ13CDIC in produced water from CBM wells with multi-coal seams was put forward.The research shows that:δ13CDIC in produced water from medium-rank coal seams commonly show positive anomalies,the produced water contains more than 15 species of methanogens,and Methanobacterium is the dominant genus.The dominant methanogens sequence numbers in the produced water are positively correlated withδ13CDIC,and the positive anomaly of v is caused by reduction of methanogens,and especially hydrogenotrophic methanogens.Vertical segmentation of sedimentary facies and lithology in stratum with multi-coal seams will result in permeability and water cut segmentation,which will lead to the segmentation ofδ13CDIC and archaea community in produced water,so in the strata with better permeability and high water cut,theδ13CDIC of the produced water is abnormally enriched,and the dominant archaea is mainly Methanobacterium.In the strata with weak permeability and low water cut,theδ13CDIC of the produced water is small,and the microbial action is weak.The shallow layer close to the coal seam outcrop is likely to be affected by meteoric precipitation,so theδ13CDIC of the produced water is smaller.The geological response model ofδ13CDIC in produced water from multi-coal seams CBM wells in the medium-rank coal reveals the geological mechanism and microbial action mechanism of theδ13CDIC difference in the produced water from the multi-coal seams CBM wells.It also provides effective geochemical evidence for the superimposed fluid system controlled by sedimentary facies,and can also be used for the contribution analysis of the produced gas and water by the multi-layer CBM wells.展开更多
Wellbore instability is a key problem restricting efficient production of coal-bed methane. In order to perform thorough and systematic research regarding coal-bed wellbore stability problems, a new discrete element m...Wellbore instability is a key problem restricting efficient production of coal-bed methane. In order to perform thorough and systematic research regarding coal-bed wellbore stability problems, a new discrete element model which fully considers the features of cleat coal-beds is established based on the Kirsch equation. With this model, the safe pipe tripping speed, drilling fluid density window and coal- bed collapse/fracture pressure are determined; in addition, the relationships between pipe tripping speed and pipe size, cleat size, etc. and wellbore stability are analyzed in the coal-bed drilling and pipe tripping processes. The case studies show the following results： the wellbore collapses （collapse pressure： 4.33 MPa） or fractures （fracture pressure： 12.7 MPa） in certain directions as a result of swab or surge pressure when the pipe tripping speed is higher than a certain value; the cleat face size has a great influence on wellbore stability, and if the drilling fluid pressure is too low, the wellbore is prone to collapse when the ratio of the face cleat size to butt cleat size is reduced; however, if the drilling fluid pressure is high enough, the butt cleat size has no influence on the wellbore fracture; the factors influencing coal-bed stability include the movement length, pipe size, borehole size.展开更多
Based on the analytical solution of gas diffusion in spherical coal particles with a constant diffusion coefficient, a calculation method of time-varying diffusion coefficient is proposed by constructing objective fun...Based on the analytical solution of gas diffusion in spherical coal particles with a constant diffusion coefficient, a calculation method of time-varying diffusion coefficient is proposed by constructing objective function. The time-varying diffusion behavior of methane, nitrogen and carbon dioxide in the coal particles was studied. The results show that with the increase of diffusion time, the diffusion coefficients of methane, nitrogen and carbon dioxide gas in the coal particles exhibit an attenuation characteristic, eventually approaching a limit value individually. The diffusion coefficient of carbon dioxide is larger than methane, and the diffusion coefficient of nitrogen is smallest. Significant phenomenon of limited diffusion was observed for coal of strong adsorption capability. Through the analysis of the diffusion coefficient of gases at different diffusion time, a mathematical model describing the time-varying diffusion characteristic of gases is obtained. The implementation of mixed gases to replace coal bed methane has a very important practical significance.展开更多
The crack volume strain method and acoustic emission(AE)method are used to analyze the anisotropy of the crack initiation strength,damage strength,the failure mode and the AE characteristics of coal reservoir.The resu...The crack volume strain method and acoustic emission(AE)method are used to analyze the anisotropy of the crack initiation strength,damage strength,the failure mode and the AE characteristics of coal reservoir.The results show that coal reservoirs show obvious anisotropic characteristics in compressive strength,cracking initiation strength and damage strength.The compressive strength of coal reservoirs decreases with the increase of bedding angle,but the reservoirs with bedding angles of 450 and 900 differ little in compressive strength.The crack initiation strength and damage strength decrease first and then increase with the increase of bedding angle.The crack initiation strength and damage strength are the highest,at the bedding angle of 0°,moderate at the bedding angle of 90°,and lowest at the bedding angle of 45°.When the bedding angle is 0°,the failure of the coal reservoirs is mainly steady propagation of large-scale fractures.When the bedding angle is 45°,one type of failure is caused by steady propagation of small-scale fractures,and the other type of failure is due to a sudden instability of large-scale fractures.When the bedding angle is 90°,the failure is mainly demonstrated by a sudden-instability of small-scale fractures.Compared with the cumulative count method of the AE,the cumulative energy method is more suitable for determining crack initiation strength and damage strength of coal reservoirs.展开更多
Sorption isotherms of hydrocarbon and carbon dioxide （CO2） provide crucial information for designing processes to sequester CO2 and recover natural gas from unmineable coal beds. Methane （CH4）, ethane （C2H6）, an...Sorption isotherms of hydrocarbon and carbon dioxide （CO2） provide crucial information for designing processes to sequester CO2 and recover natural gas from unmineable coal beds. Methane （CH4）, ethane （C2H6）, and CO2 adsorption isotherms on dry coal and the temperature effect on their maximum sorption capacity have been studied by performing combined Monte Carlo （MC） and molecular dynamics （MD） simulations at temperatures of 308 and 370 K （35 and 97 ~C） and at pressures up to 10 MPa. Simulation results demonstrate that absolute sorption （expressed as a mass basis） divided by bulk gas density has negligible temperature effect on CH4, C2H6, and CO2 sorption on dry coal when pressure is over 6 MPa. CO2 is more closely packed due to stronger interaction with coal and the stronger interaction between CO2 mole- cules compared, respectively, with the interactions between hydrocarbons and coal and between hydrocarbons. The results of this work suggest that the ＂a＂ constant （pro- portional to TcPc） in the Peng-Robinson equation of state is an important factor affecting the sorption behavior of hydrocarbons. CO2 injection pressures of lower than 8 MPa may be desirable for CH4 recovery and CO2 sequestration. This study provides a quantitative under- standing of the effects of temperature on coal sorptioncapacity for CH4, C2H6, and CO2 from a microscopic perspective.展开更多
Coal-measure gas is the natural gas generated by coal, carbonaceous shale, and dark shale in coal-measure strata. It includes resources of continuous-type coalbed methane (CBM), shale gas and tight gas reservoirs, and...Coal-measure gas is the natural gas generated by coal, carbonaceous shale, and dark shale in coal-measure strata. It includes resources of continuous-type coalbed methane (CBM), shale gas and tight gas reservoirs, and trap-type coal-bearing gas reservoirs. Huge in resources, it is an important gas source in the natural gas industry. The formation and distribution characteristics of coal-measure gas in San Juan, Surat, West Siberia and Ordos basins are introduced in this paper. By reviewing the progress of exploration and development of coal-measure gas around the world, the coal-measure gas is confirmed as an important strategic option for gas supply. This understanding is mainly manifested in three aspects. First, globally, the Eurasian east-west coal-accumulation belt and North American north-south coal-accumulation belt are two major coal-accumulation areas in the world, and the Late Carboniferous–Permian, Jurassic and end of Late Cretaceous–Neogene are 3 main coal-accumulation periods. Second, continuous-type and trap-type are two main accumulation modes of coal-measure gas;it is proposed that the area with gas generation intensity of greater than 10×10^8 m^3/km^2 is essential for the formation of large coal-measure gas field, and the CBM generated by medium- to high-rank coal is usually enriched in syncline, while CBM generated by low-rank coal is likely to accumulate when the source rock and caprock are in good configuration. Third, it is predicted that coal-measure gas around the world has huge remaining resources, coal-measure gas outside source is concentrated in Central Asia-Russia, the United States, Canada and other countries/regions, while CBM inside source is largely concentrated in 12 countries. The production of coal-measure gas in China is expected to exceed 1000×10^8 m^3 by 2030, including (500–550)×10^8 m^3 conventional coal-measure gas,(400–450)×10^8 m^3 coal-measure tight gas, and (150–200)×10^8 m^3 CBM.展开更多
基金sponsored by statutory research University of Science and Technology AGH,Cracow,Poland(No.11 100 281)
文摘In some worldwide hard coal basins recovery of methane from virgin coal beds is difficult. In general,mentioned difficulties are related to geo-mechanical, petrographical and physical-chemical properties of coals in question, occurring for example in the Bowen Basin(Australia) or the Upper Silesian Coal Basin(Poland). Among numerous properties and parameters, the following are very essential: susceptibility of coal beds to deformation connected with coal stress state change and contemporary shrinkage of the coal matrix during methane desorption. Those adverse geo-mechanical and physical-chemical effects are accompanied by essential change of the porous coal structure, which under these disadvantageous conditions is very complex. This study aims to show difficulties, which occur in phase of recognition of the methane-reach coal deposit. Volume absorbed methane(not surface adsorbed) in sub-micropores having minimal size comparable with gas molecule diameter must possess energy allowing separation of the nodes and methane release to micropores.
基金supported by the National Natural Science Foundation of China(Grant No.51176051)the PetroChina Innovation Foundation(2012D- 5006-0210)the Colleges and Universities High-level Talents Program of Guangdong
文摘Coal bed methane （CBM） has a huge potential to be purified to relieve the shortage of natural gas meanwhile to weaken the greenhouse effect. This paper proposed an optimal design strategy for CBM to obtain an integrated process configuration consisting of three each single separation units, membrane, pressure swing absorption, and cryogenics. A superstructure model was established including all possible network configurations which were solved by MINLP. The design strategy optimized the separation unit configuration and operating conditions to satisfy the target of minimum total annual process cost. An example was presented for the separation of CH4/N2 mixtures in coal bed methane （CBM） treatment. The key operation parameters were also studied and they showed the influence to process configurations.
基金This paper was jointly sponsored by a National Science and Technology Major Special Project of China(No.2016ZX05044)a Postdoctoral Science Foundation of China(No.2018M631181)a Key Project of the Natural Science Foundation of China(No.40730422).We thank all of the parties that contributed to this publication.
文摘The geothermal fields of coal-bearing strata have become a key topic in geological research into coal and coal bed methane(CBM).Based on temperature data from 135 boreholes that penetrate the Upper Permian coal-bearing strata in the Bide-Santang basin,western Guizhou,the precisions of geothermal predictions made using a geothermal gradient model and a gray sequence GM(1,1)model are analyzed and compared.The results indicate that the gray sequence GM(1,1)model is more appropriate for the prediction of geothermal fields.The GM(1,1)model is used to predict the geothermal field at three levels with depths of 500,1000,and 1500 m,as well as within the No.6,No.16,and No.27 coal seams.The results indicate that the geotemperatures of the 500 m depth level are between 21.0 and 30.0°C,indicating no heat damage;the geotemperatures of the 1000 m depth level are between 29.4 and 44.7°C,indicating the first level of heat damage;and the geotemperatures of the 1500 m depth level are between35.6 and 63.4°C,indicating the second level of heat damage.The CBM contents are positively correlated with the geotemperatures of the coal seams.The target area for CBM development is identified.
基金The financial supports received from the National Natural Science Foundation of China(21522609,21636009 and 21878328)the National Key Research and Development Program of China(Nos.2017YFC0307302,2016YFC0304003)+1 种基金the Science Foundation of China University of Petroleum,Beijing(No.2462018BJC004)Beijing Science and Technology Program,China(No.Z181100005118010)。
文摘Coal bed methane has been considered as an important energy resource.One major difficulty of purifying coal bed methane comes from the similar physical properties of CH_4 and N_2.The ZIF-8/water-glycol slurry was used as a medium to separate coal bed methane by fluidifying the solid adsorbent material.The sorption equilibrium experiment of binary mixture(CH_4/N_2)and slurry was conducted.The selectivity of CH_4 to N_2 is within the range of 2-6,which proved the feasibility of the slurry separation method.The modified Langmuir equation was used to describe the gas-slurry phase equilibrium behavior,and the calculated results were in good agreement with the experimental data.A continuous absorption-adsorption and desorption process on the separation of CH_4/N_2 in slurry is proposed and its mathematical model is also developed.Sensitivity analysis is conducted to determine the operation conditions and the energy performance of the proposed process was also evaluated.Feed gas contains 30 mol%of methane and the methane concentration in product gas is 95.46 mol%with the methane recovery ratio of 90.74%.The total energy consumption for per unit volume of product gas is determined as 1.846 kWh Nm^(-3).Experimental results and process simulation provide basic data for the design and operation of pilot and industrial plant.
基金supported by the National Basic Research Program of China(Nos.2009CB219603,2010CB226800,2009CB724601 and 2012BAC10B03)the National Natural Science Foundation of China(Major Program)(Nos.50490271 and 40672104)+2 种基金the National Natural Science Foundation of China(General Program)(No.40874071)the National Science&Technology Pillar Program in the Eleventh Five-Year Plan Period(Nos.2012BAB13B01 and2012BAC10B03)the Key Grant Project of Chinese Ministry of Education(No.306002)
文摘The coal bed methane content(CBMC)in the west mining area of Jincheng coalfield,southeastern Qjnshui Basin,is studied based on seismic data and well-logs together with laboratory measurements.The results show that the Shuey approximation has better adaptability according to the Zoeppritz equation result;the designed fold number for an ordinary seismic data is sufficient for post-stack data but insufficient for pre-stack data regarding the signal to noise ratio(SNR).Therefore a larger grid analysis was created in order to improve the SNR.The velocity field created by logging is better than that created by stack velocity in both accuracy and effectiveness.A reasonable distribution of the amplitude versus offset(AVO)attributes can be facilitated by taking the AVO response from logging as a standard for calibrating the amplitude distribution.Some AVO attributes have a close relationship with CBMC.The worst attribute is polarization magnitude,for which the correlation coefficient is 0.308;and the best attribute is the polarization product from intercept,of which the correlation coefficient is-0.8136.CBMC predicted by AVO attributes is better overall than that predicted by direct interpolation of CBMC;the validation error of the former is 14.47%,which is lower than that of the latter 23.30%.CBMC of this area ranges from2.5 m^3/t to 22 m^3/t.Most CBMC in the syncline is over 10m^3/t,but it is below 10m^3/t in the anticline;on the whole,CBMC in the syncline is higher than that in anticline.
基金supported by the National Natural Science Foundation of China(National R&D Program for Major Research Instruments,51827804)Youth Program of National Natural Science Foundation of China(52004299)National Science Foundation for Distinguished Young Scholars(51725404)
文摘Coalbed methane(CBM)is an important unconventional natural gas.Exploitation of multilayered CBM reservoir is still facing the challenge of low production rate.Radial borehole fracturing,which integrates radial jet drilling and hydraulic fracturing,is expected to create complex fracture networks in multilayers and enhance CBM recovery.The main purpose of this paper is to investigate the mechanisms and efficacy of radial borehole fracturing in increasing CBM production in multiple layers.First,a two-phase flow and multi-scale 3 D fracture network including radial laterals,hydraulic fractures and face/butt cleats model is established,and embedded discrete fracture model(EDFM)is applied to handle the complex fracture networks.Then,effects of natural-fracture nonuniform distribution are investigated to show the advantages of targeted stimulation for radial borehole fracturing.Finally,two field CBM wells located in eastern Yunnan-western Guizhou,China were presented to illuminate the stimulation efficiency by radial borehole fracturing.The results indicated that compared with vertical well fracturing,radial borehole fracturing can achieve higher gas/water daily production rate and cumulative gas/water production,approximately 2 times higher.Targeted communications to cleats and sweet spots and flexibility in designing radial borehole parameters in different layers so as to increase fracture-network complexity and connectivity are the major reasons for production enhancement of radial borehole fracturing.Furthermore,the integration of geology-engineering is vital for the decision of radial borehole fracturing designing scheme.The key findings of this paper could provide useful insights towards understanding the capability of radial borehole fracturing in developing CBM and coal-measure gas in multiple-thin layers.
基金Supported by the National Natural Science Foundation of China(41772155)the National Science and Technology Major Project of China(2016ZX05044-002)
文摘Based on long-term dynamic tracing of dissolved inorganic carbon(DIC)and stable carbon isotope(δ13CDIC)in produced water from 20 coalbed methane(CBM)wells in western Guizhou,the spatial-temporal dynamic variations ofδ13CDIC of the GP well group produced in multi-layer commingled manner were analyzed,and the relationship between the value ofδ13CDIC and CBM productivity was examined.The produced water samples of typical wells in the GP well group were amplified and sequenced using 16S rDNA,and a geological response model ofδ13CDIC in produced water from CBM wells with multi-coal seams was put forward.The research shows that:δ13CDIC in produced water from medium-rank coal seams commonly show positive anomalies,the produced water contains more than 15 species of methanogens,and Methanobacterium is the dominant genus.The dominant methanogens sequence numbers in the produced water are positively correlated withδ13CDIC,and the positive anomaly of v is caused by reduction of methanogens,and especially hydrogenotrophic methanogens.Vertical segmentation of sedimentary facies and lithology in stratum with multi-coal seams will result in permeability and water cut segmentation,which will lead to the segmentation ofδ13CDIC and archaea community in produced water,so in the strata with better permeability and high water cut,theδ13CDIC of the produced water is abnormally enriched,and the dominant archaea is mainly Methanobacterium.In the strata with weak permeability and low water cut,theδ13CDIC of the produced water is small,and the microbial action is weak.The shallow layer close to the coal seam outcrop is likely to be affected by meteoric precipitation,so theδ13CDIC of the produced water is smaller.The geological response model ofδ13CDIC in produced water from multi-coal seams CBM wells in the medium-rank coal reveals the geological mechanism and microbial action mechanism of theδ13CDIC difference in the produced water from the multi-coal seams CBM wells.It also provides effective geochemical evidence for the superimposed fluid system controlled by sedimentary facies,and can also be used for the contribution analysis of the produced gas and water by the multi-layer CBM wells.
文摘Wellbore instability is a key problem restricting efficient production of coal-bed methane. In order to perform thorough and systematic research regarding coal-bed wellbore stability problems, a new discrete element model which fully considers the features of cleat coal-beds is established based on the Kirsch equation. With this model, the safe pipe tripping speed, drilling fluid density window and coal- bed collapse/fracture pressure are determined; in addition, the relationships between pipe tripping speed and pipe size, cleat size, etc. and wellbore stability are analyzed in the coal-bed drilling and pipe tripping processes. The case studies show the following results： the wellbore collapses （collapse pressure： 4.33 MPa） or fractures （fracture pressure： 12.7 MPa） in certain directions as a result of swab or surge pressure when the pipe tripping speed is higher than a certain value; the cleat face size has a great influence on wellbore stability, and if the drilling fluid pressure is too low, the wellbore is prone to collapse when the ratio of the face cleat size to butt cleat size is reduced; however, if the drilling fluid pressure is high enough, the butt cleat size has no influence on the wellbore fracture; the factors influencing coal-bed stability include the movement length, pipe size, borehole size.
基金financially supported by the National Natural Science Foundation of China(21476145)the National 973 Program of Ministry of Sciences and Technologies of China(2011CB201202)
基金provided by the National Natural Science Foundation of China(No.51304237)the National Science and Technology Major Project(No.2016ZX05045004)
文摘Based on the analytical solution of gas diffusion in spherical coal particles with a constant diffusion coefficient, a calculation method of time-varying diffusion coefficient is proposed by constructing objective function. The time-varying diffusion behavior of methane, nitrogen and carbon dioxide in the coal particles was studied. The results show that with the increase of diffusion time, the diffusion coefficients of methane, nitrogen and carbon dioxide gas in the coal particles exhibit an attenuation characteristic, eventually approaching a limit value individually. The diffusion coefficient of carbon dioxide is larger than methane, and the diffusion coefficient of nitrogen is smallest. Significant phenomenon of limited diffusion was observed for coal of strong adsorption capability. Through the analysis of the diffusion coefficient of gases at different diffusion time, a mathematical model describing the time-varying diffusion characteristic of gases is obtained. The implementation of mixed gases to replace coal bed methane has a very important practical significance.
基金Supported by the National Natural Science Foundation of China(51804309,51861145403)State Key Laboratory of Water Resource Protection and Utilization in Coal Mining,China(SHJT-17-42.10)。
文摘The crack volume strain method and acoustic emission(AE)method are used to analyze the anisotropy of the crack initiation strength,damage strength,the failure mode and the AE characteristics of coal reservoir.The results show that coal reservoirs show obvious anisotropic characteristics in compressive strength,cracking initiation strength and damage strength.The compressive strength of coal reservoirs decreases with the increase of bedding angle,but the reservoirs with bedding angles of 450 and 900 differ little in compressive strength.The crack initiation strength and damage strength decrease first and then increase with the increase of bedding angle.The crack initiation strength and damage strength are the highest,at the bedding angle of 0°,moderate at the bedding angle of 90°,and lowest at the bedding angle of 45°.When the bedding angle is 0°,the failure of the coal reservoirs is mainly steady propagation of large-scale fractures.When the bedding angle is 45°,one type of failure is caused by steady propagation of small-scale fractures,and the other type of failure is due to a sudden instability of large-scale fractures.When the bedding angle is 90°,the failure is mainly demonstrated by a sudden-instability of small-scale fractures.Compared with the cumulative count method of the AE,the cumulative energy method is more suitable for determining crack initiation strength and damage strength of coal reservoirs.
基金supported by the National Basic Research Program of China (2014CB239004)the ‘‘Element and Process Constraint Petroleum System Modeling’’ project (No. 2011A-0207) under the Petro China Science Innovation program
文摘Sorption isotherms of hydrocarbon and carbon dioxide （CO2） provide crucial information for designing processes to sequester CO2 and recover natural gas from unmineable coal beds. Methane （CH4）, ethane （C2H6）, and CO2 adsorption isotherms on dry coal and the temperature effect on their maximum sorption capacity have been studied by performing combined Monte Carlo （MC） and molecular dynamics （MD） simulations at temperatures of 308 and 370 K （35 and 97 ~C） and at pressures up to 10 MPa. Simulation results demonstrate that absolute sorption （expressed as a mass basis） divided by bulk gas density has negligible temperature effect on CH4, C2H6, and CO2 sorption on dry coal when pressure is over 6 MPa. CO2 is more closely packed due to stronger interaction with coal and the stronger interaction between CO2 mole- cules compared, respectively, with the interactions between hydrocarbons and coal and between hydrocarbons. The results of this work suggest that the ＂a＂ constant （pro- portional to TcPc） in the Peng-Robinson equation of state is an important factor affecting the sorption behavior of hydrocarbons. CO2 injection pressures of lower than 8 MPa may be desirable for CH4 recovery and CO2 sequestration. This study provides a quantitative under- standing of the effects of temperature on coal sorptioncapacity for CH4, C2H6, and CO2 from a microscopic perspective.
基金Supported by the National Key Basic Research and Development Program(973 Program),China
文摘Coal-measure gas is the natural gas generated by coal, carbonaceous shale, and dark shale in coal-measure strata. It includes resources of continuous-type coalbed methane (CBM), shale gas and tight gas reservoirs, and trap-type coal-bearing gas reservoirs. Huge in resources, it is an important gas source in the natural gas industry. The formation and distribution characteristics of coal-measure gas in San Juan, Surat, West Siberia and Ordos basins are introduced in this paper. By reviewing the progress of exploration and development of coal-measure gas around the world, the coal-measure gas is confirmed as an important strategic option for gas supply. This understanding is mainly manifested in three aspects. First, globally, the Eurasian east-west coal-accumulation belt and North American north-south coal-accumulation belt are two major coal-accumulation areas in the world, and the Late Carboniferous–Permian, Jurassic and end of Late Cretaceous–Neogene are 3 main coal-accumulation periods. Second, continuous-type and trap-type are two main accumulation modes of coal-measure gas;it is proposed that the area with gas generation intensity of greater than 10×10^8 m^3/km^2 is essential for the formation of large coal-measure gas field, and the CBM generated by medium- to high-rank coal is usually enriched in syncline, while CBM generated by low-rank coal is likely to accumulate when the source rock and caprock are in good configuration. Third, it is predicted that coal-measure gas around the world has huge remaining resources, coal-measure gas outside source is concentrated in Central Asia-Russia, the United States, Canada and other countries/regions, while CBM inside source is largely concentrated in 12 countries. The production of coal-measure gas in China is expected to exceed 1000×10^8 m^3 by 2030, including (500–550)×10^8 m^3 conventional coal-measure gas,(400–450)×10^8 m^3 coal-measure tight gas, and (150–200)×10^8 m^3 CBM.
