Chloride ions(Cl^(-))have been shown to impact the long-lasting nature of reinforced concrete.However,Cl^(-)that are already bound inside the concrete will not lead to the deterioration of the concrete’s characterist...Chloride ions(Cl^(-))have been shown to impact the long-lasting nature of reinforced concrete.However,Cl^(-)that are already bound inside the concrete will not lead to the deterioration of the concrete’s characteristics.The composition of the cement-based material,including the type of cement and auxiliary materials,greatly influences the ability of the material to bind Cl^(-),and varied components result in varying binding beha-vior of the Cl^(-).Simultaneously,the Cl^(-)binding process in concrete is influenced by both the internal and exterior surroundings,as well as the curing practices.These factors impact the hydration process of the cement and the internal pore structure of the concrete.Currently,mathematical theories and molecular dynamics simulations have increasingly been employed as the prevalent methods for examining the binding behaviors of Cl^(-)in concrete.These techniques are extensively utilized for predicting the lifespan and conducting microscopic studies of reinforced concrete in Cl^(-)settings.This work proposes recommendations for future research based on a summary of experimental and simulation investigations on Cl^(-)binding.Which will offer theoretical guidance for studying the binding of Cl^(-)in cement-based materials.展开更多
The study aims to investigate the carbonated water erosion mechanism of lining concrete in tunnels traversing karst environment and enhance its resistance.In this study,dynamic carbonated water erosion was simulated t...The study aims to investigate the carbonated water erosion mechanism of lining concrete in tunnels traversing karst environment and enhance its resistance.In this study,dynamic carbonated water erosion was simulated to assess erosion depth,microstructure,phase migrations,and pore structure in various tunnel lining cement-based materials.Additionally,Ca^(2+)leaching was analyzed,and impact of Ca/Si molar ratio in hydration products on erosion resistance was discussed by thermodynamic calculations.The results indicate that carbonated water erosion caused rough and porous surface on specimens,with reduced portlandite and CaCO_(3) content,increased porosity,and an enlargement of pore size.The thermodynamic calculations indicate that the erosion is spontaneous,driven by physical dissolution and chemical reactions dominated by Gibbs free energy.And the erosion reactions proceed more spontaneously and extensively when Ca/Si molar ratio in hydration products was higher.Therefore,cement-based materials with higher portlandite content exhibit weaker erosion resistance.Model-building concrete,with C-S-H gel and portlandite as primary hydration products,has greater erosion susceptibility than shotcrete with ettringite as main hydration product.Moreover,adding silicon-rich mineral admixtures can enhance the erosion resistance.This research offers theory and tech insights to boost cement-based material resistance against carbonated water erosion in karst tunnel engineering.展开更多
Fiber reinforced polymer(FRP) composite materials are heterogeneous and anisotropic materials that do not exhibit plastic deformation. They have been used in a wide range of contemporary applications particularly in s...Fiber reinforced polymer(FRP) composite materials are heterogeneous and anisotropic materials that do not exhibit plastic deformation. They have been used in a wide range of contemporary applications particularly in space and aviation,automotive,maritime and manufacturing of sports equipment. Carbon fiber reinforced polymer(CFRP) and glass fiber reinforced polymer(GFRP) composite materials,among other fiber reinforced materials,have been increasingly replacing conventional materials with their excellent strength and low specific weight properties. Their manufacturability in varying combinations with customized strength properties,also their high fatigue,toughness and high temperature wear and oxidation resistance capabilities render these materials an excellent choice in engineering applications.In the present review study,a literature survey was conducted on the machinability properties and related approaches for CFRP and GFRP composite materials. As in the machining of all anisotropic and heterogeneous materials,failure mechanisms were also reported in the machining of CFRP and GFRP materials with both conventional and modern manufacturing methods and the results of these studies were obtained by use of variance analysis(ANOVA),artificial neural networks(ANN) model,fuzzy inference system(FIS),harmony search(HS) algorithm,genetic algorithm(GA),Taguchi's optimization technique,multi-criteria optimization,analytical modeling,stress analysis,finite elements method(FEM),data analysis,and linear regression technique. Failure mechanisms and surface quality is discussed with the help of optical and scanning electron microscopy,and profilometry. ANOVA,GA,FEM,etc. are used to analyze and generate predictive models.展开更多
A new clay-cement composite grouting material (CCGM) for tunnelling in underwater karst area was developed through the excellent synergistic interactions among cement, clay, meta-aluminate and lignin. The probable for...A new clay-cement composite grouting material (CCGM) for tunnelling in underwater karst area was developed through the excellent synergistic interactions among cement, clay, meta-aluminate and lignin. The probable formation mechanism of the material was proposed based on a series of experimental tests. The results show that with an optimal mass ratio (2:1:1:0.024) for water, cement, clay and additives, the obtained CCGM displayed an excellent grouting performance for karst in an underwater condition. Compared with neat cement grouts and clay-cement grouts, CCGM has faster gel time, lower bleeding rate and bulk shrinkage rate, greater initial viscosity, and a strong resistance to water dispersion. A successful engineering application indicates that CCGM not only fulfils a better grouting performance for karst in underwater conditions but also reduces the engineering cost and environmental pollution.展开更多
Na0.44MnO2 nanorods have been prepared by a hydrothermal method.The experimental parameters have been systematically investigated and optimized.The results show that Na0.44MnO2 nanorods obtained via the hydrothermal t...Na0.44MnO2 nanorods have been prepared by a hydrothermal method.The experimental parameters have been systematically investigated and optimized.The results show that Na0.44MnO2 nanorods obtained via the hydrothermal treatment at 200℃for 16 h show the best electrochemical properties,which deliver the high initial discharge capacity of 110.7 mA·h/g at 50 mA/g in potential window 2.0-4.0 V.To further improve their electrochemical properties,a ball milling process with graphene has been carried out to obtain Na0.44MnO2/graphene composite.The initial discharge capacity of Na0.44MnO2/graphene composite is 106.9 mA·h/g at a current density of 50 mA/g.After 100 cycles,the residual discharge capacity is 91.8 mA·h/g and the capacity retention rate is 85.9%,which is much higher than that of pristine Na0.44MnO2 nanorods(74.7%)at the same condition.What is more,when the current density reaches 500 and 1000 mA/g,the corresponding discharge capacities of Na0.44MnO2/graphene composite are about 89 and 78 mA·h/g,respectively,indicating outstanding rate capability.展开更多
Taking the nano-sized carbon black and aniline monomer as precursor and （NH4）2S2O6 as oxidant, the well coated C/polyaniline（C/PANI） composite materials were prepared by in situ polymerization of the aniline on th...Taking the nano-sized carbon black and aniline monomer as precursor and （NH4）2S2O6 as oxidant, the well coated C/polyaniline（C/PANI） composite materials were prepared by in situ polymerization of the aniline on the surface of well-dispersed nano-sized carbon black for supercapacitor. The micro-structure of the C/PANI composite electrode materials were analyzed by SEM. The electrochemical properties of C/ PANI and PANI composite electrode were characterized by means of the galvanostatic charge-discharge experiment, cyclic voltammetric measurement and impedance spectroscopy analysis. The results show that by adding the nano-sized carbon black in the process of chemical polymerization of the aniline, the polyaniline can be in situ polymerized and well-coated onto the carbon black particles, which may effectively improve the aggregation of particles and the electrolyte penetration. What’s more , the maximum of specific capacitance of C/PANI electrode 437.6F·g -1 can be attained. Compared with PANI electrode, C/PANI electrode shows more desired capacitance characteristics, smaller internal resistance and better cycle performance.展开更多
The hydration mechanism of low quality fly ash in cement-based materials was investigated. The hydration heat of the composite cementitious materials was determined by isothermal calorimetry, and the hydration product...The hydration mechanism of low quality fly ash in cement-based materials was investigated. The hydration heat of the composite cementitious materials was determined by isothermal calorimetry, and the hydration products, quantity, pore structure and morphology were measured by X-ray diffraction(XRD), thermalgravity-differential thermal analysis(TG-DTA), mercury intrusion porosimetry(MIP) and scanning electron microscopy(SEM), respectively. The results indicate that grinding could not only improve the physical properties of the low quality fly ash on particle effect, but also improve hydration properties of the cementitious system from various aspects compared with raw low quality fly ash(RLFA). At the early stage of hydration, the low quanlity fly ash acts as almost inert material; but then at the later stage, high chemical activity, especially for ground low quality fly ash(GLFA), could be observed. It can accelerate the formation of hydration products containing more chemical bonded water, resulting in higher degree of cement hydration, thus denser microstructure and more reasonable pore size distribution, but the hydration heat in total is reduced. It can also delay the induction period, but the accelerating period is shortened and there is little influence on the second exothermic peak.展开更多
The transmission and distribution of moisture in cement-based materials are of great significance to the properties and durability of materials. Traditional macro-humidity monitoring equipment in civil engineering can...The transmission and distribution of moisture in cement-based materials are of great significance to the properties and durability of materials. Traditional macro-humidity monitoring equipment in civil engineering cannot capture the microscale humidity inside cement-based materials in situ. In this paper, a method of using rhodamine 6G fluorescence to characterize the change in relative humidity in cement-based materials is proposed. Two kinds of moulding processes are designed, which are premixed and smeared after moulding, and the optimal preparation concentration is explored. The results showed that rhodamine 6G can reflect the relative humidity of cement-based materials in situ by its fluorescence intensity and had little effect on the hydration heat release and hydration products of cement-based materials;the fluorescence intensity was much higher when the internal relative humidity was 63% and 75%. The research results lead the application of polymer materials in the field of traditional building materials, help to explore the performance evolution law of cement-based materials in micro scale, and have important significance for the evolution from single discipline to interdisciplinary.展开更多
A motor-driven linkage system with links fabricated from 3-dimensional braided composite materials was studied. A group of coupling dynamic equations of the system, including composite materials parameters, electromag...A motor-driven linkage system with links fabricated from 3-dimensional braided composite materials was studied. A group of coupling dynamic equations of the system, including composite materials parameters, electromagnetism parameters of the motor and structural parameters of the link mechanism, were established by finite element method. Based on the air-gap field of non-uniform airspace of three-phase alternating current motor caused by the vibration eccentricity of rotor, the relation of electromechanical coupling at the actual running state was analyzed. And the motor element, which defines the transverse vibration and torsional vibration of the motor as its nodal displacement, was established. Then, based on the damping element model and the expression of energy dissipation of the 3-dimentional braided composite materials, the damping matrix of the system was established by calculating each order modal damping of the mechanism.展开更多
Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of...Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of TiB2/C composite cathode material were investigated. The results show that thermogravimetrie behavior of pitch and TiB2/C green composite cathode is similar, and appears the largest mass loss rate in the temperature range from 200 to 600 ℃. The bulk density variation of sample K5 before and after baking is the largest （11.9%）, that of sample K25 is the second, and that of sample M5 is the smallest （6.7%）. The crushing strength of sample M5 is the biggest （51.2 MPa）, that of sample K2.5 is the next, and that of sample K5 is the smallest （32.8 MPa）. But, the orders of the electrical resistivity and electrolysis expansion of samples are just opposite with the order of crushing strength. The heating rate has a great impact on the microstructure of sample. The faster the heating rate is, the bigger the pore size and porosity of sample are. Compared with the heating rate between 200 and 600℃ of samples K25 and K5, that of sample M5 is slower and suitable for baking process of TiB2/C composite cathode material.展开更多
Based on deeply discussing the deformation mechanism of composite foundation with discrete material pile, firstly, the settlement of composite foundation in rigid foundation conditions was assumed to consist of two pa...Based on deeply discussing the deformation mechanism of composite foundation with discrete material pile, firstly, the settlement of composite foundation in rigid foundation conditions was assumed to consist of two parts, an expanding part and an un-expanding part. Then, in view of the differences of deformation properties between the expanding part and the un-expanding part, the relationships between the pile modulus and the applied load in these two parts were respectively developed. Thirdly, by introducing the above relationships into settlement analysis, a new method to calculate displacement of composite foundation with discrete material pile was proposed by using the multi-stage loading theory and the layer-wise summation approach. This method is effective not only for accounting for the effect of variations of pores on deformation modulus of the pile body in different depths, but also for describing the characteristics of different deformation mechanisms of the pile body with varying depth. Finally, the proposed method was used to a practical composite foundation problem, whose theoretical results were presented and compared to those of other methods. The rationality and feasibility of this method are identified through comparative analysis.展开更多
In recent years,composite materials have been used in many industries such as in automotive,aerospace,telecommunication,marine,furniture,construction and defence.Body amour and tank spall liners are examples of the us...In recent years,composite materials have been used in many industries such as in automotive,aerospace,telecommunication,marine,furniture,construction and defence.Body amour and tank spall liners are examples of the use of composites in defence industry.Composites have many different attributes that are unique over conventional materials like metals,polymers and ceramics.Those attributes include light weight,high specific stiffness and strength properties,corrosion resistance,aesthetically pleasing and ease of fabrication.Advanced composites such as aramid and carbon fibre polymer composites,metal matrix composites,ceramic matrix composites,and nanocomposites are among material contenders in defence technology applications requiring excellent structural integrity.Composites are also used in some non-structural applications in selected components utilising the low cost advantage of glass fibre and natural fibre composites.展开更多
The permeability modeling of self-healing due to calcium carbonate precipitation in cement-based materials with mineral additives was studied in this work. The parameters of calcium carbonate precipitation during self...The permeability modeling of self-healing due to calcium carbonate precipitation in cement-based materials with mineral additives was studied in this work. The parameters of calcium carbonate precipitation during self-healing were simulated. A permeability modeling of self-healing, combined with numerical simulation of calcium carbonate formation, was proposed based on the modified Poiseuille flow model. Moreover, the percentage of calcium carbonate in healing products was measured by TG-DTA. The simulated results show that self-healing can be dramatically promoted with the increase of pH and Ca2+ concentration. The calculated result of permeability is consistent with that measured for cracks appearing in middle or later stages of self-healing, it indicates that this model can be used to predict the self-healing rate to some extent. In addition, TG-DTA results show that the percentage of calcium carbonate in healing products is higher for mortar with only chemical expansion additives or cracks appearing in the later stage, which can more accurately predict the self-healing rate for the model.展开更多
Composite materials exhibit the impressive mechanical properties of high damping and stiffness,which cannot be attained by employing conventional single materials.Along these lines,a novel material architecture is pre...Composite materials exhibit the impressive mechanical properties of high damping and stiffness,which cannot be attained by employing conventional single materials.Along these lines,a novel material architecture is presented in this work in order to fabricate composites with enhanced mechanical characteristics.More specifically,entangled metallic wire materials were used as the active matrix,whereas polyurethane was employed as the reinforcement elements.As a result,an entangled metallic wire material-polyurethane composite with high damping and stiffness was prepared by enforcing the vacuum infiltration method.On top of that,the mechanical properties(loss factor,energy consumption,and average stiffness)of the proposed composite materials were characterized by performing dynamic tests,and its fatigue characteristics were verified by the micro-interface bonding,as well as the macro-damage factor.The impact of the density,preloading spacing,loading amplitude,and exciting frequency on the mechanical properties of the composites were also thoroughly analyzed.The extracted results indicate that the mechanical properties of the composites were significantly enhanced than those of the pure materials due to the introduction of interface friction.Moreover,the average stiffness of the composites was about 10 times the respective value of the entangled metallic wire material.Interestingly,a rise in the loading period leads to some failure between the composite interfaces,which reduces the stiffness property but enhances the damping dissipation properties.Finally,a comprehensive dynamic mechanical model of the composites was established,while it was experimentally verified.The proposed composites possess higher damping features,i.e.,stiffness characteristics,and maintain better fatigue characteristics,which can broaden the application range of the composites.In addition,we provide a theoretical and experimental framework for the research and applications in the field of metal matrix composites.展开更多
In pursuit of more efficient and stable electrochemical energy storage materials,composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and...In pursuit of more efficient and stable electrochemical energy storage materials,composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and exceptional properties.Graphene oxide(GO),a two-dimensional material with an extremely high specific surface area and excellent conductivity,offers new possibilities for enhancing the electrochemical performance of metal oxides.In this work,we synthesized met-al-organic framework(MOF)and GO composites by regulating the amount of GO,and successfully prepared composites of metal oxides supported by nitrogen-doped carbon frameworks and GO through a simple one-step calcination process.Based on the electrochemical tests,the optimal amount of GO was determined.This research will provide new insights into and directions for designing and synthesizing metal oxide and graphene oxide composite materials with an ideal electro-chemical performance.展开更多
Military missions in hostile environments are often costly and unpredictable,with squadrons sometimes facing isolation and resource scarcity.In such scenarios,critical components in vehicles,drones,and energy generato...Military missions in hostile environments are often costly and unpredictable,with squadrons sometimes facing isolation and resource scarcity.In such scenarios,critical components in vehicles,drones,and energy generators may require structural reinforcement or repair due to damage.This paper proposes a portable,on-site production method for molds under challenging conditions,where material supply is limited.The method utilizes large format additive manufacturing(LFAM)with recycled composite materials,sourced from end-of-life components and waste,as feedstock.The study investigates the microstructural effects of recycling through shredding techniques,using microscopic imaging.Three potential defense-sector applications are explored,specifically in the aerospace,automotive,and energy industries.Additionally,the influence of key printing parameters,particularly nonparallel plane deposition at a 45-degree angle,on the mechanical behavior of ABS reinforced with 20%glass fiber(GF)is examined.The results demonstrate the feasibility of this manufacturing approach,highlighting reductions in waste material and production times compared to traditional methods.Shorter layer times were found to reduce thermal gradients between layers,thereby improving layer adhesion.While 45-degree deposition enhanced Young's modulus,it slightly reduced interlayer adhesion quality.Furthermore,recycling-induced fiber length reduction led to material degradation,aligning with findings from previous studies.Challenges encountered during implementation included weak part adherence to the print bed and local excess material deposition.Overall,the proposed methodology offers a cost-effective alternative to traditional CNC machining for mold production,demonstrating its potential for on-demand manufacturing in resource-constrained environments.展开更多
As the second most important solid waste produced by coal-fired power plants,the improper management of coal-fired slag has the potential to result in environmental pollution.It is therefore imperative that high-value...As the second most important solid waste produced by coal-fired power plants,the improper management of coal-fired slag has the potential to result in environmental pollution.It is therefore imperative that high-value utilization pathways for coal-fired slag should be developed.In this study,modified magnesium slag(MMS),produced by a magnesium smelter,was selected as the alkali activator.The activated silica-aluminum solid wastes,namely coal-fired slag(CFS)and mineral powder(MP),were employed as pozzolanic materials in the preparation of alkali-activated cementitious materials.The alkali-activated cementitious materials prepared with 50 wt%MMS,40 wt%CFS and 10 wt%MP exhibited favorable mechanical properties,with a compressive strength of 32.804 MPa in the paste sample cured for 28 d.Then,the activated silica-aluminum solid waste consisting of CFS-MP generated a significant amount of C-S(A)-H gels,AFt,and other products,which were observed to occupy the pore structure of the specimen.In addition,the secondary hydration reaction of CFS-MP occurs in high alkalinity environments,resulting in the formation of a mutually stimulated and promoted reaction system between CFS-MP and MMS,this will subsequently accelerate the hydrolysis reaction of MMS.It is important to emphasize that the amount of MMS in alkali-activated cementitious materials must be strictly regulated to avert the potential issue of incomplete depolymerization-repolymerization of active silica-aluminum solid waste containing CFS-MP.This in turn could have a deleterious impact on the late strength of the cementitious materials.The aim of this work is to improve the joint disposal of MMS,CFS and MP and thereby provide a scientific basis for the development of environmentally friendly and low-carbon modified magnesium slag alkali-activated coal-fired slag based cementitious materials for mine backfilling.展开更多
Significance of body material and temperature variation on burning time and burning rate of Si/Pb O/Pb_3O_4/FG and B/BaCrO_4/FG pyrotechnic delay compositions were experimentally studied. Brass and stainless steel wer...Significance of body material and temperature variation on burning time and burning rate of Si/Pb O/Pb_3O_4/FG and B/BaCrO_4/FG pyrotechnic delay compositions were experimentally studied. Brass and stainless steel were used as delay body materials. High resolution oscilloscope and a customized chronometer were simultaneously used for the measurement of burning time and burning rate. Results reveal that brass material with controlled column dimensions reduced the variation in burning time of Si/Pb O/Pb_3O_4/FG delay mixture from 7.43% to 4.17% and that of B/Ba CrO_4/FG mixture from 16.83% to 9.39%.Similarly the variation in burning rate was reduced from 7.57% to 4.12% and from 17% to 9.69% for Si/Pb O/Pb_3O_4/FG and B/BaCrO_4/FG mixtures respectively. Si/PbO/Pb_3O_4/FG delay mixture was also subjected to temperature ranging from -54℃ up to+100℃. The burning rate of this composition varied linearly with temperature. Burning rate increased from 28.01 mm/s to 34.38 mm/s when the temperature was varied from -54℃ to +100℃.展开更多
A Pt-free counter electrode(CE)composed of La_(2)Mo_(2)O_(7)(La_(2)O_(3)-2MoO_(2))was successfully synthesized via the simple pyrolysis of lanthanum acetate(C6H9O6La·xH2O)and hexaammonium heptamolybdate tetrahydr...A Pt-free counter electrode(CE)composed of La_(2)Mo_(2)O_(7)(La_(2)O_(3)-2MoO_(2))was successfully synthesized via the simple pyrolysis of lanthanum acetate(C6H9O6La·xH2O)and hexaammonium heptamolybdate tetrahydrate((NH_(4))6Mo_(7)O_(24)·4H2O)in a high-temperature solid-state reaction.Also,La_(2)Mo_(2)O_(7)and multiwall carbon nanotubes(MWCNTs)are combined using two methods.La_(2)Mo_(2)O_(7)/MWCNTs was prepared by spray-coating La_(2)Mo_(2)O_(7)over the surface of MWCNTs,and La_(2)Mo_(2)O_(7)@MWCNTs was synthesized by doping La_(2)Mo_(2)O_(7)into MWCNTs.The two types of composite materials were further used as Pt-free catalytic material in CEs in dye sensitized solar cells(DSSCs).The morphology and microstructure of La_(2)Mo_(2)O_(7)/MWCNTs and La_(2)Mo_(2)O_(7)@MWCNTs were determined using scanning electron microscopy and X-ray diffraction.The electrochemical performance of the La_(2)Mo_(2)O_(7)/MWCNTs and La_(2)Mo_(2)O_(7)@MWCNTs composite catalysts for CEs was determined using photocurrent-voltage measurements,cyclic voltammetry,electrochemical impedance spectroscopy,and Tafel polarization in encapsulation of DSSCs batteries.The experimental results show that power conversion efficiencies of 6.09%and 4.84%were obtained for La_(2)Mo_(2)O_(7)/MWCNTs and La_(2)Mo_(2)O_(7)@MWCNTs,respectively,as CEs toward the reduction of I3-/I-ions,and these values are superior to those of MWCNTs(3.94%)and the La_(2)Mo_(2)O_(7)(0.87%)electrode under the same conditions.The enhanced electrode performance was attributed to the relatively larger surface area and higher conductivity of the La_(2)Mo_(2)O_(7)/MWCNTs composite catalysts.展开更多
文摘Chloride ions(Cl^(-))have been shown to impact the long-lasting nature of reinforced concrete.However,Cl^(-)that are already bound inside the concrete will not lead to the deterioration of the concrete’s characteristics.The composition of the cement-based material,including the type of cement and auxiliary materials,greatly influences the ability of the material to bind Cl^(-),and varied components result in varying binding beha-vior of the Cl^(-).Simultaneously,the Cl^(-)binding process in concrete is influenced by both the internal and exterior surroundings,as well as the curing practices.These factors impact the hydration process of the cement and the internal pore structure of the concrete.Currently,mathematical theories and molecular dynamics simulations have increasingly been employed as the prevalent methods for examining the binding behaviors of Cl^(-)in concrete.These techniques are extensively utilized for predicting the lifespan and conducting microscopic studies of reinforced concrete in Cl^(-)settings.This work proposes recommendations for future research based on a summary of experimental and simulation investigations on Cl^(-)binding.Which will offer theoretical guidance for studying the binding of Cl^(-)in cement-based materials.
基金Project(2021YJ059)supported by the Research Project of China Academy of Railway Sciences。
文摘The study aims to investigate the carbonated water erosion mechanism of lining concrete in tunnels traversing karst environment and enhance its resistance.In this study,dynamic carbonated water erosion was simulated to assess erosion depth,microstructure,phase migrations,and pore structure in various tunnel lining cement-based materials.Additionally,Ca^(2+)leaching was analyzed,and impact of Ca/Si molar ratio in hydration products on erosion resistance was discussed by thermodynamic calculations.The results indicate that carbonated water erosion caused rough and porous surface on specimens,with reduced portlandite and CaCO_(3) content,increased porosity,and an enlargement of pore size.The thermodynamic calculations indicate that the erosion is spontaneous,driven by physical dissolution and chemical reactions dominated by Gibbs free energy.And the erosion reactions proceed more spontaneously and extensively when Ca/Si molar ratio in hydration products was higher.Therefore,cement-based materials with higher portlandite content exhibit weaker erosion resistance.Model-building concrete,with C-S-H gel and portlandite as primary hydration products,has greater erosion susceptibility than shotcrete with ettringite as main hydration product.Moreover,adding silicon-rich mineral admixtures can enhance the erosion resistance.This research offers theory and tech insights to boost cement-based material resistance against carbonated water erosion in karst tunnel engineering.
文摘Fiber reinforced polymer(FRP) composite materials are heterogeneous and anisotropic materials that do not exhibit plastic deformation. They have been used in a wide range of contemporary applications particularly in space and aviation,automotive,maritime and manufacturing of sports equipment. Carbon fiber reinforced polymer(CFRP) and glass fiber reinforced polymer(GFRP) composite materials,among other fiber reinforced materials,have been increasingly replacing conventional materials with their excellent strength and low specific weight properties. Their manufacturability in varying combinations with customized strength properties,also their high fatigue,toughness and high temperature wear and oxidation resistance capabilities render these materials an excellent choice in engineering applications.In the present review study,a literature survey was conducted on the machinability properties and related approaches for CFRP and GFRP composite materials. As in the machining of all anisotropic and heterogeneous materials,failure mechanisms were also reported in the machining of CFRP and GFRP materials with both conventional and modern manufacturing methods and the results of these studies were obtained by use of variance analysis(ANOVA),artificial neural networks(ANN) model,fuzzy inference system(FIS),harmony search(HS) algorithm,genetic algorithm(GA),Taguchi's optimization technique,multi-criteria optimization,analytical modeling,stress analysis,finite elements method(FEM),data analysis,and linear regression technique. Failure mechanisms and surface quality is discussed with the help of optical and scanning electron microscopy,and profilometry. ANOVA,GA,FEM,etc. are used to analyze and generate predictive models.
基金Project(51608539)supported by the National Natural Science Foundation of ChinaProjects(2016M592451,2017T100610)supported by the China Postdoctoral Science Foundation
文摘A new clay-cement composite grouting material (CCGM) for tunnelling in underwater karst area was developed through the excellent synergistic interactions among cement, clay, meta-aluminate and lignin. The probable formation mechanism of the material was proposed based on a series of experimental tests. The results show that with an optimal mass ratio (2:1:1:0.024) for water, cement, clay and additives, the obtained CCGM displayed an excellent grouting performance for karst in an underwater condition. Compared with neat cement grouts and clay-cement grouts, CCGM has faster gel time, lower bleeding rate and bulk shrinkage rate, greater initial viscosity, and a strong resistance to water dispersion. A successful engineering application indicates that CCGM not only fulfils a better grouting performance for karst in underwater conditions but also reduces the engineering cost and environmental pollution.
基金Project(51672234)supported by the National Natural Science Foundation of ChinaProject(1337304)supported by the Program for Innovative Research Cultivation Team in University,Ministry of Education,China
文摘Na0.44MnO2 nanorods have been prepared by a hydrothermal method.The experimental parameters have been systematically investigated and optimized.The results show that Na0.44MnO2 nanorods obtained via the hydrothermal treatment at 200℃for 16 h show the best electrochemical properties,which deliver the high initial discharge capacity of 110.7 mA·h/g at 50 mA/g in potential window 2.0-4.0 V.To further improve their electrochemical properties,a ball milling process with graphene has been carried out to obtain Na0.44MnO2/graphene composite.The initial discharge capacity of Na0.44MnO2/graphene composite is 106.9 mA·h/g at a current density of 50 mA/g.After 100 cycles,the residual discharge capacity is 91.8 mA·h/g and the capacity retention rate is 85.9%,which is much higher than that of pristine Na0.44MnO2 nanorods(74.7%)at the same condition.What is more,when the current density reaches 500 and 1000 mA/g,the corresponding discharge capacities of Na0.44MnO2/graphene composite are about 89 and 78 mA·h/g,respectively,indicating outstanding rate capability.
基金Project(2005CB623703) supported by the National Basic Research Program of China project(5JJ30103) supported bythe Natural Science Foundation of Hunan Province
文摘Taking the nano-sized carbon black and aniline monomer as precursor and （NH4）2S2O6 as oxidant, the well coated C/polyaniline（C/PANI） composite materials were prepared by in situ polymerization of the aniline on the surface of well-dispersed nano-sized carbon black for supercapacitor. The micro-structure of the C/PANI composite electrode materials were analyzed by SEM. The electrochemical properties of C/ PANI and PANI composite electrode were characterized by means of the galvanostatic charge-discharge experiment, cyclic voltammetric measurement and impedance spectroscopy analysis. The results show that by adding the nano-sized carbon black in the process of chemical polymerization of the aniline, the polyaniline can be in situ polymerized and well-coated onto the carbon black particles, which may effectively improve the aggregation of particles and the electrolyte penetration. What’s more , the maximum of specific capacitance of C/PANI electrode 437.6F·g -1 can be attained. Compared with PANI electrode, C/PANI electrode shows more desired capacitance characteristics, smaller internal resistance and better cycle performance.
基金Project(51208391) supported by the National Natural Science Foundation of China
文摘The hydration mechanism of low quality fly ash in cement-based materials was investigated. The hydration heat of the composite cementitious materials was determined by isothermal calorimetry, and the hydration products, quantity, pore structure and morphology were measured by X-ray diffraction(XRD), thermalgravity-differential thermal analysis(TG-DTA), mercury intrusion porosimetry(MIP) and scanning electron microscopy(SEM), respectively. The results indicate that grinding could not only improve the physical properties of the low quality fly ash on particle effect, but also improve hydration properties of the cementitious system from various aspects compared with raw low quality fly ash(RLFA). At the early stage of hydration, the low quanlity fly ash acts as almost inert material; but then at the later stage, high chemical activity, especially for ground low quality fly ash(GLFA), could be observed. It can accelerate the formation of hydration products containing more chemical bonded water, resulting in higher degree of cement hydration, thus denser microstructure and more reasonable pore size distribution, but the hydration heat in total is reduced. It can also delay the induction period, but the accelerating period is shortened and there is little influence on the second exothermic peak.
基金Project(2018YFD1101002) supported by the National Key R&D Program of ChinaProject(51308405) supported by the National Natural Science Foundation of China。
文摘The transmission and distribution of moisture in cement-based materials are of great significance to the properties and durability of materials. Traditional macro-humidity monitoring equipment in civil engineering cannot capture the microscale humidity inside cement-based materials in situ. In this paper, a method of using rhodamine 6G fluorescence to characterize the change in relative humidity in cement-based materials is proposed. Two kinds of moulding processes are designed, which are premixed and smeared after moulding, and the optimal preparation concentration is explored. The results showed that rhodamine 6G can reflect the relative humidity of cement-based materials in situ by its fluorescence intensity and had little effect on the hydration heat release and hydration products of cement-based materials;the fluorescence intensity was much higher when the internal relative humidity was 63% and 75%. The research results lead the application of polymer materials in the field of traditional building materials, help to explore the performance evolution law of cement-based materials in micro scale, and have important significance for the evolution from single discipline to interdisciplinary.
基金Project(50175031) supported by the National Natural Science Foundation of China
文摘A motor-driven linkage system with links fabricated from 3-dimensional braided composite materials was studied. A group of coupling dynamic equations of the system, including composite materials parameters, electromagnetism parameters of the motor and structural parameters of the link mechanism, were established by finite element method. Based on the air-gap field of non-uniform airspace of three-phase alternating current motor caused by the vibration eccentricity of rotor, the relation of electromechanical coupling at the actual running state was analyzed. And the motor element, which defines the transverse vibration and torsional vibration of the motor as its nodal displacement, was established. Then, based on the damping element model and the expression of energy dissipation of the 3-dimentional braided composite materials, the damping matrix of the system was established by calculating each order modal damping of the mechanism.
基金Project (2005CB623703) supported by the Major State Basic Research and Development Program of ChinaProject (2008AA030502) supported by the National High-Tech Research and Development Program of China
文摘Pitch and TiB2/C green composite cathode material were respectively analyzed with simultaneous DSC-TGA, and effects of three baking processes of TiB2/C composite cathode material, i.e. K25, K5 and M5, on properties of TiB2/C composite cathode material were investigated. The results show that thermogravimetrie behavior of pitch and TiB2/C green composite cathode is similar, and appears the largest mass loss rate in the temperature range from 200 to 600 ℃. The bulk density variation of sample K5 before and after baking is the largest （11.9%）, that of sample K25 is the second, and that of sample M5 is the smallest （6.7%）. The crushing strength of sample M5 is the biggest （51.2 MPa）, that of sample K2.5 is the next, and that of sample K5 is the smallest （32.8 MPa）. But, the orders of the electrical resistivity and electrolysis expansion of samples are just opposite with the order of crushing strength. The heating rate has a great impact on the microstructure of sample. The faster the heating rate is, the bigger the pore size and porosity of sample are. Compared with the heating rate between 200 and 600℃ of samples K25 and K5, that of sample M5 is slower and suitable for baking process of TiB2/C composite cathode material.
基金Project (2006AA11Z104) supported by the Hi-tech Reasearch and Development Program of ChinaProject (08JJ3115) supported by the Natural Science Foundation of Hunan Province, China
文摘Based on deeply discussing the deformation mechanism of composite foundation with discrete material pile, firstly, the settlement of composite foundation in rigid foundation conditions was assumed to consist of two parts, an expanding part and an un-expanding part. Then, in view of the differences of deformation properties between the expanding part and the un-expanding part, the relationships between the pile modulus and the applied load in these two parts were respectively developed. Thirdly, by introducing the above relationships into settlement analysis, a new method to calculate displacement of composite foundation with discrete material pile was proposed by using the multi-stage loading theory and the layer-wise summation approach. This method is effective not only for accounting for the effect of variations of pores on deformation modulus of the pile body in different depths, but also for describing the characteristics of different deformation mechanisms of the pile body with varying depth. Finally, the proposed method was used to a practical composite foundation problem, whose theoretical results were presented and compared to those of other methods. The rationality and feasibility of this method are identified through comparative analysis.
文摘In recent years,composite materials have been used in many industries such as in automotive,aerospace,telecommunication,marine,furniture,construction and defence.Body amour and tank spall liners are examples of the use of composites in defence industry.Composites have many different attributes that are unique over conventional materials like metals,polymers and ceramics.Those attributes include light weight,high specific stiffness and strength properties,corrosion resistance,aesthetically pleasing and ease of fabrication.Advanced composites such as aramid and carbon fibre polymer composites,metal matrix composites,ceramic matrix composites,and nanocomposites are among material contenders in defence technology applications requiring excellent structural integrity.Composites are also used in some non-structural applications in selected components utilising the low cost advantage of glass fibre and natural fibre composites.
基金Project(2018YFC0705404)supported by the National Key Technology Research and Development of ChinaProjects(51878480,51678442,51878481,51878496)supported by the National Natural Science Foundation of China+1 种基金Project(U1534207)supported by the National High-speed Train Union Fund,ChinaProject supported by the Fundamental Research Funds for the Central Universities,China
文摘The permeability modeling of self-healing due to calcium carbonate precipitation in cement-based materials with mineral additives was studied in this work. The parameters of calcium carbonate precipitation during self-healing were simulated. A permeability modeling of self-healing, combined with numerical simulation of calcium carbonate formation, was proposed based on the modified Poiseuille flow model. Moreover, the percentage of calcium carbonate in healing products was measured by TG-DTA. The simulated results show that self-healing can be dramatically promoted with the increase of pH and Ca2+ concentration. The calculated result of permeability is consistent with that measured for cracks appearing in middle or later stages of self-healing, it indicates that this model can be used to predict the self-healing rate to some extent. In addition, TG-DTA results show that the percentage of calcium carbonate in healing products is higher for mortar with only chemical expansion additives or cracks appearing in the later stage, which can more accurately predict the self-healing rate for the model.
基金National Natural Science Foundation of China(Grant No.52175162,51805086 and 51975123)Natural Science Foundation of Fujian Province(Grant No.2019J01210)Health education joint project of Fujian Province(Grant No.2019-WJ-01)。
文摘Composite materials exhibit the impressive mechanical properties of high damping and stiffness,which cannot be attained by employing conventional single materials.Along these lines,a novel material architecture is presented in this work in order to fabricate composites with enhanced mechanical characteristics.More specifically,entangled metallic wire materials were used as the active matrix,whereas polyurethane was employed as the reinforcement elements.As a result,an entangled metallic wire material-polyurethane composite with high damping and stiffness was prepared by enforcing the vacuum infiltration method.On top of that,the mechanical properties(loss factor,energy consumption,and average stiffness)of the proposed composite materials were characterized by performing dynamic tests,and its fatigue characteristics were verified by the micro-interface bonding,as well as the macro-damage factor.The impact of the density,preloading spacing,loading amplitude,and exciting frequency on the mechanical properties of the composites were also thoroughly analyzed.The extracted results indicate that the mechanical properties of the composites were significantly enhanced than those of the pure materials due to the introduction of interface friction.Moreover,the average stiffness of the composites was about 10 times the respective value of the entangled metallic wire material.Interestingly,a rise in the loading period leads to some failure between the composite interfaces,which reduces the stiffness property but enhances the damping dissipation properties.Finally,a comprehensive dynamic mechanical model of the composites was established,while it was experimentally verified.The proposed composites possess higher damping features,i.e.,stiffness characteristics,and maintain better fatigue characteristics,which can broaden the application range of the composites.In addition,we provide a theoretical and experimental framework for the research and applications in the field of metal matrix composites.
基金supported by the National Natural Science Foundation of China(51971157)Shenzhen Science and Technology Program(JCYJ20210324115412035,JCYJ202103-24123202008,JCYJ20210324122803009 and ZDS-YS20210813095534001)Guangdong Foundation for Basic and Applied Basic Research Program(2021A1515110880).
文摘In pursuit of more efficient and stable electrochemical energy storage materials,composite materials consisting of metal oxides and graphene oxide have garnered significant attention due to their unique structures and exceptional properties.Graphene oxide(GO),a two-dimensional material with an extremely high specific surface area and excellent conductivity,offers new possibilities for enhancing the electrochemical performance of metal oxides.In this work,we synthesized met-al-organic framework(MOF)and GO composites by regulating the amount of GO,and successfully prepared composites of metal oxides supported by nitrogen-doped carbon frameworks and GO through a simple one-step calcination process.Based on the electrochemical tests,the optimal amount of GO was determined.This research will provide new insights into and directions for designing and synthesizing metal oxide and graphene oxide composite materials with an ideal electro-chemical performance.
基金Generalitat Valenciana(GVA)and Spanish Ministry of Science and Innovation(Grant Nos.TED2021-130879 B-C21,CIACIF/2021/286,PID2023-151110OB-I00,and CIPROM/2022/3)to provide funds for conducting experiments and software licensessupported by the National Research Foundation,Prime Minister's Office,Singapore under its Campus for Research Excellence and Technological Enterprise(CREATE)programme。
文摘Military missions in hostile environments are often costly and unpredictable,with squadrons sometimes facing isolation and resource scarcity.In such scenarios,critical components in vehicles,drones,and energy generators may require structural reinforcement or repair due to damage.This paper proposes a portable,on-site production method for molds under challenging conditions,where material supply is limited.The method utilizes large format additive manufacturing(LFAM)with recycled composite materials,sourced from end-of-life components and waste,as feedstock.The study investigates the microstructural effects of recycling through shredding techniques,using microscopic imaging.Three potential defense-sector applications are explored,specifically in the aerospace,automotive,and energy industries.Additionally,the influence of key printing parameters,particularly nonparallel plane deposition at a 45-degree angle,on the mechanical behavior of ABS reinforced with 20%glass fiber(GF)is examined.The results demonstrate the feasibility of this manufacturing approach,highlighting reductions in waste material and production times compared to traditional methods.Shorter layer times were found to reduce thermal gradients between layers,thereby improving layer adhesion.While 45-degree deposition enhanced Young's modulus,it slightly reduced interlayer adhesion quality.Furthermore,recycling-induced fiber length reduction led to material degradation,aligning with findings from previous studies.Challenges encountered during implementation included weak part adherence to the print bed and local excess material deposition.Overall,the proposed methodology offers a cost-effective alternative to traditional CNC machining for mold production,demonstrating its potential for on-demand manufacturing in resource-constrained environments.
基金Projects(52222404,52074212)supported by the National Natural Science Foundation of ChinaProject(2023-LL-QY-07)supported by the Two-chain Integration Key Projects in Shaanxi Province,China。
文摘As the second most important solid waste produced by coal-fired power plants,the improper management of coal-fired slag has the potential to result in environmental pollution.It is therefore imperative that high-value utilization pathways for coal-fired slag should be developed.In this study,modified magnesium slag(MMS),produced by a magnesium smelter,was selected as the alkali activator.The activated silica-aluminum solid wastes,namely coal-fired slag(CFS)and mineral powder(MP),were employed as pozzolanic materials in the preparation of alkali-activated cementitious materials.The alkali-activated cementitious materials prepared with 50 wt%MMS,40 wt%CFS and 10 wt%MP exhibited favorable mechanical properties,with a compressive strength of 32.804 MPa in the paste sample cured for 28 d.Then,the activated silica-aluminum solid waste consisting of CFS-MP generated a significant amount of C-S(A)-H gels,AFt,and other products,which were observed to occupy the pore structure of the specimen.In addition,the secondary hydration reaction of CFS-MP occurs in high alkalinity environments,resulting in the formation of a mutually stimulated and promoted reaction system between CFS-MP and MMS,this will subsequently accelerate the hydrolysis reaction of MMS.It is important to emphasize that the amount of MMS in alkali-activated cementitious materials must be strictly regulated to avert the potential issue of incomplete depolymerization-repolymerization of active silica-aluminum solid waste containing CFS-MP.This in turn could have a deleterious impact on the late strength of the cementitious materials.The aim of this work is to improve the joint disposal of MMS,CFS and MP and thereby provide a scientific basis for the development of environmentally friendly and low-carbon modified magnesium slag alkali-activated coal-fired slag based cementitious materials for mine backfilling.
文摘Significance of body material and temperature variation on burning time and burning rate of Si/Pb O/Pb_3O_4/FG and B/BaCrO_4/FG pyrotechnic delay compositions were experimentally studied. Brass and stainless steel were used as delay body materials. High resolution oscilloscope and a customized chronometer were simultaneously used for the measurement of burning time and burning rate. Results reveal that brass material with controlled column dimensions reduced the variation in burning time of Si/Pb O/Pb_3O_4/FG delay mixture from 7.43% to 4.17% and that of B/Ba CrO_4/FG mixture from 16.83% to 9.39%.Similarly the variation in burning rate was reduced from 7.57% to 4.12% and from 17% to 9.69% for Si/Pb O/Pb_3O_4/FG and B/BaCrO_4/FG mixtures respectively. Si/PbO/Pb_3O_4/FG delay mixture was also subjected to temperature ranging from -54℃ up to+100℃. The burning rate of this composition varied linearly with temperature. Burning rate increased from 28.01 mm/s to 34.38 mm/s when the temperature was varied from -54℃ to +100℃.
文摘A Pt-free counter electrode(CE)composed of La_(2)Mo_(2)O_(7)(La_(2)O_(3)-2MoO_(2))was successfully synthesized via the simple pyrolysis of lanthanum acetate(C6H9O6La·xH2O)and hexaammonium heptamolybdate tetrahydrate((NH_(4))6Mo_(7)O_(24)·4H2O)in a high-temperature solid-state reaction.Also,La_(2)Mo_(2)O_(7)and multiwall carbon nanotubes(MWCNTs)are combined using two methods.La_(2)Mo_(2)O_(7)/MWCNTs was prepared by spray-coating La_(2)Mo_(2)O_(7)over the surface of MWCNTs,and La_(2)Mo_(2)O_(7)@MWCNTs was synthesized by doping La_(2)Mo_(2)O_(7)into MWCNTs.The two types of composite materials were further used as Pt-free catalytic material in CEs in dye sensitized solar cells(DSSCs).The morphology and microstructure of La_(2)Mo_(2)O_(7)/MWCNTs and La_(2)Mo_(2)O_(7)@MWCNTs were determined using scanning electron microscopy and X-ray diffraction.The electrochemical performance of the La_(2)Mo_(2)O_(7)/MWCNTs and La_(2)Mo_(2)O_(7)@MWCNTs composite catalysts for CEs was determined using photocurrent-voltage measurements,cyclic voltammetry,electrochemical impedance spectroscopy,and Tafel polarization in encapsulation of DSSCs batteries.The experimental results show that power conversion efficiencies of 6.09%and 4.84%were obtained for La_(2)Mo_(2)O_(7)/MWCNTs and La_(2)Mo_(2)O_(7)@MWCNTs,respectively,as CEs toward the reduction of I3-/I-ions,and these values are superior to those of MWCNTs(3.94%)and the La_(2)Mo_(2)O_(7)(0.87%)electrode under the same conditions.The enhanced electrode performance was attributed to the relatively larger surface area and higher conductivity of the La_(2)Mo_(2)O_(7)/MWCNTs composite catalysts.
