Orbital angular momentum(OAM)at radio frequency(RF)has attracted more and more attention as a novel approach of multiplexing a set of orthogonal OAM modes on the same frequency channel to achieve high spectral efficie...Orbital angular momentum(OAM)at radio frequency(RF)has attracted more and more attention as a novel approach of multiplexing a set of orthogonal OAM modes on the same frequency channel to achieve high spectral efficiency(SE).However,the precondition for maintaining the orthogonality among different OAM modes is perfect alignment of the transmit and receive uniform circular arrays(UCAs),which is difficult to be satisfied in practical wireless communication scenarios.Therefore,to achieve available multi-mode OAM broadband wireless communication,we first investigate the effect of oblique angles on the transmission performance of the multi-mode OAM broadband system in the non-parallel misalignment case.Then,we compare the UCA-based RF analog and baseband digital transceiver structures and corresponding beam steering schemes.Mathematical analysis and numerical simulations validate that the SE of the misaligned multi-mode OAM broadband system is quite low,while analog and digital beam steering(DBS)both can significantly improve the SE of the system.However,DBS can obtain higher SE than analog beam steering especially when the bandwidth and the number of array elements are large,which validates that the baseband digital transceiver with DBS is more suitable for multi-mode OAM broadband wireless communication systems in practice.展开更多
Metalens technology has been applied extensively in miniaturized and integrated infrared imaging systems.However,due to the high phase dispersion of unit structures,metalens often exhibits chromatic aberration,making ...Metalens technology has been applied extensively in miniaturized and integrated infrared imaging systems.However,due to the high phase dispersion of unit structures,metalens often exhibits chromatic aberration,making broadband achromatic infrared imaging challenging to achieve.In this paper,six different unit structures based on chalcogenide glass are constructed,and their phase-dispersion parameters are analyzed to establish a database.On this basis,using chromatic aberration compensation and parameterized adjoint topology optimization,a broadband achromatic metalens with a numerical aperture of 0.5 is designed by arranging these six unit structures in the far-infrared band.Simulation results show that the metalens achieves near diffraction-limited focusing within the operating wavelength range of 9−11μm,demonstrating the good performance of achromatic aberration with flat focusing efficiency of 54%−58%across all wavelengths.展开更多
[Background and purposes]In recent years,there has been growing attention in academia and industry on the development of high-performance electromagnetic wave(EMW)absorbing materials.However,creating lightweight broad...[Background and purposes]In recent years,there has been growing attention in academia and industry on the development of high-performance electromagnetic wave(EMW)absorbing materials.However,creating lightweight broadband absorbers remains a challenge in terms of practical applications.EMW absorbing materials primarily rely on the magnetic loss of magnetic materials and/or the dielectric loss of dielectric materials to convert EMW energy into thermal energy for dissipation.Among various magnetic materials,Fe_(3)O_(4) plays an irreplaceable role in EMW absorption due to its high saturation magnetization,low cost and compatible dielectric loss in the gigahertz frequency range.Nevertheless,the high density,large matching thickness and narrow absorption bandwidth of Fe_(3)O_(4) pose significant challenges for practical applications.In contrast,one-dimensional(1D)structures not only retain the characteristic properties of lightweight,chemical stability and high dielectric loss,but also exhibit anisotropic structures and large aspect ratios.Additionally,researchers have found that the minimum reflection loss(RL)of hollow carbon materials with mesopores is nearly four times that of non-porous hollow carbon materials and nine times that of dense carbon materials.According to Maxwell's EMW theory,composites consisting of Fe_(3)O_(4) and one-dimensional(1D)mesoporous carbon materials can leverage their respective advantages by optimizing the composition and structure of the composites to balance u,and Er,thereby enhancing EMW absorption performance.Additionally,numerous studies have demonstrated that composites composed of multi-component heterostructures significantly enhance the EAB.This enhancement is primarily ascribed to the numerous interface polarization losses generated by the additional heterostructure interfaces,which also improve the overall impedance matching of the composites.In this study,we leverage the advantages of magnetic/carbon composites,one-dimensional(1D)mesoporous carbon and multi-component heterostructures to prepare a composite of 1D mesoporous carbon-coated manganese oxide(Mn_(3)O_(4) and MnO,denoted as Mn_(x)O_(y))embedded with Fe_(3)0_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4)).This composite was synthesized and its formation mechanism and microstructure were analyzed in detail.At the same time,the influence of this Mn_(x)O_(y)/C@Fe_(3)O_(4) structure on EMW properties and absorbing performance was further discussed.[Methods]Firstly,MnO_(2) nanowires were synthesized by using a simple hydrothermal method.Then,the MnO_(2) nanowires served as templates for the synthesis of MnO_(2)/PDA@Fe^(3+)composites through the in-situ polymerization of dopamine and Fe^(3+)adsorption.Finally,1D mesoporous carbon-coated manganese oxide composite embedded with Fe_(3)O_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4))composites were obtained after heat treatment at 550℃ in N_(2).The crystal structure of the samples was analyzed using X-ray diffractometer with Cu Ka irradiation.Scanning electron microscopy(SEM)and high-resolution transmission electron microscopy(TEM)were used to observe microstructure and morphology of the samples.Nitrogen sorption measurements were obtained at 77 K on a Quantachrome surface area and pore size analyzer to measure the specific surface area and pore size distribution.XPS analysis was performed on X-ray photoelectron spectrometer with monochromatic Al Ka radiation.Magnetization curves of the samples were recorded with a Quantum Design physical property measurement system(PPMS-9)at room temperature.The electromagnetic parameters of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites were measured using an Agilent N5230C network analyzer in the frequency range of 2-18 GHz.For electromagentic testing,the Mn,Oy/C@Fe34 composites and paraffin wax were mixed at 50°C according to the mass ratio of 15 wt.%,20 wt.%and 25 wt.%,and pressed in a special mold to make coaxial rings(inner diameter=3.04 mm,outer diameter-7 mm),which were denoted as S-1,S-2 and S-3,respectively.[Results]SEM images illustrate the preparation process of iD mesoporous carbon-coated manganese oxide embedded with Fe3O4 nanoparticles composites(Mn_(x)O_(y)/C@Fe_(3)O_(4)).Most of the manganese oxide(Mn,Oy)was reduced to granular after heat treatment,while the outer carbon layer remains its 1D morphology and the carbon layer is interspersed with Fe_(3)O_(4) nanoparticles.The diffraction peaks of MnO_(2) nanowires align well with the body-centered tetragonal a-MnO2.For the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites,the signals of α-MnO_(2) disappears,followed by the emergence of Mn_(3)O_(4) and three prominent diffraction peaks for the cubic MnO.In addition,four weak diffraction peaks correspond to the magnetite Fe_(3)O_(4),consistent with the HRTEM results.The corresponding nitrogen adsorption-desorption isotherm and pore size distribution curve are presented to further analyze the mesoporous structure of composite.The surface composition and element valence states of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite were investigated by using XPS.The polarization relaxation processes were analyzed according to the Debye theory which describes the relationship between e'and e".Besides the polarization loss,the contribution of the conduction loss plays an important role for the overall dielectric loss.The magnetization curve of Mn_(x)O_(y)/C@Fe_(3)O_(4) exhibits typical ferromagnetic behavior.The permittivity parameter(Co),defined as Co=u"(u)^(-2)f^(-1) determine the contribution of eddy current effect to magnetic loss.The tand values are all larger than those of tand,for the three samples,indicating that the loss capacity of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites is mainly derived from the dielectric loss.Although tand,is smaller,it plays an important role in improving the impedance matching of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites.When the filler loading is 15 wt.%,the RL of sample S-1 is about-10.0 dB at the thickness of 1.5 mm with narrow EAB.As the filler loading increased to 20 wt.%,the RL of sample S-2 reached-62.0 dB at a thickness of 2.2 mm and the EAB was 6.4 GHz at a small thickness of 1.7 mm.When the filler loading is further increased to 25 wt.%,the microwave absorption performance of sample S3 decreased significantly with a little region of RL<-10.0 dB at the thickness of 5.0 mm.The values of[Zin/Zol of the three samples at thicknesses of 1.5-5.0 mm were calculated.Due to good impedance matching of S-2,the incident EMW can enter the material and then can be dissipated through dipole polarization loss,interface polarization loss,conduction loss,eddy current loss and natural ferromagnetic resonance loss.[Conclusions]1D Mn_(x)O_(y)/C@Fe_(3)O_(4) was synthesized via a process involving the coating of polydopamine,adsorption of Fe(ll)salts and heat treatment,using MnO_(2) nanowires as templates.The multi-component heterostructure of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite(Mn_(3)O_(4),MnO,Fe_(3)O_(4),and C)enhances the interfacial interactions between the different phases,providing increased interface polarization loss under the action of an alternating electromagnetic field.The numerous defects and terminal groups in the mesoporous carbon provide abundant dipole polarization centers.Additionally,the presence of mesopores reduces the weight of the material while increasing the multiple scattering losses of the electromagnetic waves within the material.The ID carbon structure in the matrix forms a conductive network between adjacent fibers,facilitating electron migration and transition,thereby enhancing conductive loss.The incorporation of magnetic Fe_(3)O_(4) nanoparticles introduces eddy current loss and natural ferromagnetic resonance loss,thus increasing magnetic loss.Moreover,the synergistic effect between dielectric and magnetic losses improves the impedance matching of the material,leading to excellent EMW absorption performance.展开更多
Broadband near-infrared(NIR)luminescent materials have shown great promise in applications such as optical communication,biomedicine,and optoelectronic devices.However,the current research is focused on phos⁃phors and...Broadband near-infrared(NIR)luminescent materials have shown great promise in applications such as optical communication,biomedicine,and optoelectronic devices.However,the current research is focused on phos⁃phors and glasses,and it is important to develop broadband NIR luminescent nanomaterials.Here,we report an erbi⁃um-sensitized core-shell nanocrystal design for broadband NIR emission.Based on the structural design with suitable dopings of Tm^(3+)and Ho^(3+),the broadband NIR emission covering 1.5-2.1μm region is achieved under 980 nm and 808 nm excitations.Moreover,the emission intensity is further enhanced by introducing Yb^(3+)and Nd^(3+)into the sam⁃ple,respectively,and the energy transfer processes between them are systematically discussed.Our results present a novel approach for developing broadband NIR luminescent materials and devices.展开更多
A Yb:CaGd_(0.33)Y_(0.625)AlO_(4)(Yb:CGYA)laser crystal of high optical quality has been successfully synthesized via the Czochralski method.The introduction of Gd^(3+)ions preserves the original structure and efficien...A Yb:CaGd_(0.33)Y_(0.625)AlO_(4)(Yb:CGYA)laser crystal of high optical quality has been successfully synthesized via the Czochralski method.The introduction of Gd^(3+)ions preserves the original structure and efficiently generates inhomogeneous broadening of the Yb^(3+)ion emission spectra.The fluorescence emission peak wavelength of the Yb:CGYA crystal is 1053 nm,and the corresponding measured full width at halfmaximum is 93 nm.A tunable laser output ranging from 1017 nm to 1073 nm is achieved by using a birefringent filter,which represents the broadest tuning range reported in a short cavity to date.The compact laser offers significant advantages for its applications around the 1μm wavelength band.展开更多
A millimeter-wave (mmW) broadband dual circularly polarized (dual-CP) antenna with high port isolation is proposed in this paper. The dual-CP performance is realized based on the symmetrical septum circular polarizer ...A millimeter-wave (mmW) broadband dual circularly polarized (dual-CP) antenna with high port isolation is proposed in this paper. The dual-CP performance is realized based on the symmetrical septum circular polarizer based on the gap waveguide (GWG) technology. Two sets of symmetrical septum circular polarizers are used for common aperture combination,achieving the broadband dual-CP characteristics. Taking advantage of GWG structure without good electrical contact, the antenna can also be fabricated and assembled easily in the mmW band. The principle analysis of the antenna is given, and the antenna is simulated and fabricated. The measured results show that the bandwidth for S11lower than-10.7 dB and the axial ratio (AR) lower than 2.90 dB in 75-110 GHz, with realative bandwidth of 38%. Over the frequency band, the gain is higher than 9.16 dBic, and the dual-CP port isolation is greater than32 dB. The proposed antenna with dual-CP and highly isolated in a wide bandwidth range has broad application prospects in the field of mmW communication.展开更多
Adaptive broadband beamforraing is a key issue in array applications. The adaptive broadband beamformer with tapped delay line （TDL） structure for nonuniform linear array （NLA） is designed according to the rule of...Adaptive broadband beamforraing is a key issue in array applications. The adaptive broadband beamformer with tapped delay line （TDL） structure for nonuniform linear array （NLA） is designed according to the rule of minimizing the beamformer＇s output power while keeping the distortionless response （DR） in the direction of desired signal and keeping the constant beamwidth （CB） with the prescribed sidelobe level over the whole operating band. This kind of beamforming problem can be solved with the interior-point method after being converted to the form of standard second order cone programming （SOCP）. The computer simulations are presented which illustrate the effectiveness of our beamformer.展开更多
In modern active and passive sonar systems, broadband beamforming for acoustic arrays is widely used to suppress unwanted interference and to detect target signals of interest. A broadband low sidelobe beamforming sch...In modern active and passive sonar systems, broadband beamforming for acoustic arrays is widely used to suppress unwanted interference and to detect target signals of interest. A broadband low sidelobe beamforming scheme in time domain is proposed in this paper. The first step of this scheme is to delay the outputs of each element in the acoustic array by a tapped-delay-line (TDL) to accomplish the integer part of the time delay need to form a beam. Then, finite impulse response (FIR) digital filters are used to implement the fractional part of the time delay. The weighting coefficients for all array elements at different frequencies to realize the low sidelobe beams are also implemented with the FIR digital filters. Finally, the outputs of the digital filters are summed up to yield the time domain beam output. The design of low sidelobe beam pattern and that of the FIR digital filters are two crucial technical issues in this beamforming procedure. The low sidelobe beams of each sub-band are designed using the optimized beam synthesis approach based on the principle of MVDR beamforming. An improved adaptive approach are used for the design of FIR digital filters, and the design requirements of these filters were specified by the weights of low sidelobe beams of each sub-band over the broad frequency band. Results of computer simulation for a twelve-element arc array show that the beamforming scheme is very effective in forming low sidelobe broadband beam.展开更多
In order to suppress the low-frequency ultrasound vibration in the broadband range of 20 k Hz—100 k Hz,this paper proposes and discusses an acoustic metamaterial with low-frequency ultrasound vibration attenuation pr...In order to suppress the low-frequency ultrasound vibration in the broadband range of 20 k Hz—100 k Hz,this paper proposes and discusses an acoustic metamaterial with low-frequency ultrasound vibration attenuation properties,which is configured by hybrid arc and sharp-angle convergent star-shaped lattices.The effect of the dispersion relation and the bandgap characteristic for the scatterers in star-shaped are simulated and analyzed.The target bandgap width is extended by optimizing the geometry parameters of arc and sharp-angle convergent lattices.The proposed metamaterial configured by optimized hybrid lattices exhibits remarkable broad bandgap characteristics by bandgap complementarity,and the simulation results verify a 99%vibration attenuation amplitude can be obtained in the frequency of20 k Hz—100 k Hz.After the fabrication of the proposed hybrid configurational star-shaped metamaterial by 3D printing technique,the transmission loss experiments are performed,and the experimental results indicate that the fabricated metamaterial has the characteristics of broadband vibration attenuation and an amplitude greater than 85%attenuation for the target frequency.These results demonstrate that the hybrid configurational star-shaped metamaterials can effectively widen the bandgap and realize high efficiency attenuation,which has capability for the vibration attenuation in the application of highprecise equipment.展开更多
Microstrip transmission lines connecting to the millimeter wave radar chip and antenna significantly affect the radiation efficiency and bandwidth of the antenna.Here,a wideband non-uniform wavy microstrip line for co...Microstrip transmission lines connecting to the millimeter wave radar chip and antenna significantly affect the radiation efficiency and bandwidth of the antenna.Here,a wideband non-uniform wavy microstrip line for complex impedance in automotive radar frequency range is proposed.Unlike the gradient transmission line,the wavy structure is composed of periodically semi-circular segments.By adjusting the radius of the semi-circular,the surface current is varied and concentrated on the semi-circular segments,allowing a wider tunability range of the resonant frequency.The results reveal that the bandwidth of the loaded wavy transmission line antenna improves to 9.37 GHz,which is 5.81 GHz wider than that of the loaded gradient line.The gain and the half power beam width of the loaded antenna are about 14.69 dB and 9.58°,respectively.The proposed non-uniform microstrip line scheme may open up a route for realizing wideband millimeter-wave automotive radar applications.展开更多
本文阐述了高速铁路(以下简称高铁)宽带无线接入系统的需求,研究了高铁宽带无线接入系统的特点,分析了现有无线接入技术的优势与不足,探讨了一种新型的高铁宽带无线接入结构High Speed Mobile Cell(Himocell),最后讨论了高铁宽带无线接...本文阐述了高速铁路(以下简称高铁)宽带无线接入系统的需求,研究了高铁宽带无线接入系统的特点,分析了现有无线接入技术的优势与不足,探讨了一种新型的高铁宽带无线接入结构High Speed Mobile Cell(Himocell),最后讨论了高铁宽带无线接入中的几个关键技术。展开更多
基金supported by the Natural Science Basic Research Program of Shaanxi(2021JZ-18)the Natural Science Foundation of Guangdong Province of China(2021A1515010812)+1 种基金the Open Research Fund of National Mobile Communications Research Laboratory,Southeast University(2021D04)the Fundamental Research Funds for Central Universities,and the Innovation Fund of Xidian University。
文摘Orbital angular momentum(OAM)at radio frequency(RF)has attracted more and more attention as a novel approach of multiplexing a set of orthogonal OAM modes on the same frequency channel to achieve high spectral efficiency(SE).However,the precondition for maintaining the orthogonality among different OAM modes is perfect alignment of the transmit and receive uniform circular arrays(UCAs),which is difficult to be satisfied in practical wireless communication scenarios.Therefore,to achieve available multi-mode OAM broadband wireless communication,we first investigate the effect of oblique angles on the transmission performance of the multi-mode OAM broadband system in the non-parallel misalignment case.Then,we compare the UCA-based RF analog and baseband digital transceiver structures and corresponding beam steering schemes.Mathematical analysis and numerical simulations validate that the SE of the misaligned multi-mode OAM broadband system is quite low,while analog and digital beam steering(DBS)both can significantly improve the SE of the system.However,DBS can obtain higher SE than analog beam steering especially when the bandwidth and the number of array elements are large,which validates that the baseband digital transceiver with DBS is more suitable for multi-mode OAM broadband wireless communication systems in practice.
文摘Metalens technology has been applied extensively in miniaturized and integrated infrared imaging systems.However,due to the high phase dispersion of unit structures,metalens often exhibits chromatic aberration,making broadband achromatic infrared imaging challenging to achieve.In this paper,six different unit structures based on chalcogenide glass are constructed,and their phase-dispersion parameters are analyzed to establish a database.On this basis,using chromatic aberration compensation and parameterized adjoint topology optimization,a broadband achromatic metalens with a numerical aperture of 0.5 is designed by arranging these six unit structures in the far-infrared band.Simulation results show that the metalens achieves near diffraction-limited focusing within the operating wavelength range of 9−11μm,demonstrating the good performance of achromatic aberration with flat focusing efficiency of 54%−58%across all wavelengths.
基金National Natural Science Foundation of China (52371171, 52222106, 51971008, 52121001)Fund of National Key Laboratory of Scattering and Radiation (Beijing Institute of Environmental Features)。
文摘[Background and purposes]In recent years,there has been growing attention in academia and industry on the development of high-performance electromagnetic wave(EMW)absorbing materials.However,creating lightweight broadband absorbers remains a challenge in terms of practical applications.EMW absorbing materials primarily rely on the magnetic loss of magnetic materials and/or the dielectric loss of dielectric materials to convert EMW energy into thermal energy for dissipation.Among various magnetic materials,Fe_(3)O_(4) plays an irreplaceable role in EMW absorption due to its high saturation magnetization,low cost and compatible dielectric loss in the gigahertz frequency range.Nevertheless,the high density,large matching thickness and narrow absorption bandwidth of Fe_(3)O_(4) pose significant challenges for practical applications.In contrast,one-dimensional(1D)structures not only retain the characteristic properties of lightweight,chemical stability and high dielectric loss,but also exhibit anisotropic structures and large aspect ratios.Additionally,researchers have found that the minimum reflection loss(RL)of hollow carbon materials with mesopores is nearly four times that of non-porous hollow carbon materials and nine times that of dense carbon materials.According to Maxwell's EMW theory,composites consisting of Fe_(3)O_(4) and one-dimensional(1D)mesoporous carbon materials can leverage their respective advantages by optimizing the composition and structure of the composites to balance u,and Er,thereby enhancing EMW absorption performance.Additionally,numerous studies have demonstrated that composites composed of multi-component heterostructures significantly enhance the EAB.This enhancement is primarily ascribed to the numerous interface polarization losses generated by the additional heterostructure interfaces,which also improve the overall impedance matching of the composites.In this study,we leverage the advantages of magnetic/carbon composites,one-dimensional(1D)mesoporous carbon and multi-component heterostructures to prepare a composite of 1D mesoporous carbon-coated manganese oxide(Mn_(3)O_(4) and MnO,denoted as Mn_(x)O_(y))embedded with Fe_(3)0_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4)).This composite was synthesized and its formation mechanism and microstructure were analyzed in detail.At the same time,the influence of this Mn_(x)O_(y)/C@Fe_(3)O_(4) structure on EMW properties and absorbing performance was further discussed.[Methods]Firstly,MnO_(2) nanowires were synthesized by using a simple hydrothermal method.Then,the MnO_(2) nanowires served as templates for the synthesis of MnO_(2)/PDA@Fe^(3+)composites through the in-situ polymerization of dopamine and Fe^(3+)adsorption.Finally,1D mesoporous carbon-coated manganese oxide composite embedded with Fe_(3)O_(4) nanoparticles(Mn_(x)O_(y)/C@Fe_(3)O_(4))composites were obtained after heat treatment at 550℃ in N_(2).The crystal structure of the samples was analyzed using X-ray diffractometer with Cu Ka irradiation.Scanning electron microscopy(SEM)and high-resolution transmission electron microscopy(TEM)were used to observe microstructure and morphology of the samples.Nitrogen sorption measurements were obtained at 77 K on a Quantachrome surface area and pore size analyzer to measure the specific surface area and pore size distribution.XPS analysis was performed on X-ray photoelectron spectrometer with monochromatic Al Ka radiation.Magnetization curves of the samples were recorded with a Quantum Design physical property measurement system(PPMS-9)at room temperature.The electromagnetic parameters of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites were measured using an Agilent N5230C network analyzer in the frequency range of 2-18 GHz.For electromagentic testing,the Mn,Oy/C@Fe34 composites and paraffin wax were mixed at 50°C according to the mass ratio of 15 wt.%,20 wt.%and 25 wt.%,and pressed in a special mold to make coaxial rings(inner diameter=3.04 mm,outer diameter-7 mm),which were denoted as S-1,S-2 and S-3,respectively.[Results]SEM images illustrate the preparation process of iD mesoporous carbon-coated manganese oxide embedded with Fe3O4 nanoparticles composites(Mn_(x)O_(y)/C@Fe_(3)O_(4)).Most of the manganese oxide(Mn,Oy)was reduced to granular after heat treatment,while the outer carbon layer remains its 1D morphology and the carbon layer is interspersed with Fe_(3)O_(4) nanoparticles.The diffraction peaks of MnO_(2) nanowires align well with the body-centered tetragonal a-MnO2.For the Mn_(x)O_(y)/C@Fe_(3)O_(4) composites,the signals of α-MnO_(2) disappears,followed by the emergence of Mn_(3)O_(4) and three prominent diffraction peaks for the cubic MnO.In addition,four weak diffraction peaks correspond to the magnetite Fe_(3)O_(4),consistent with the HRTEM results.The corresponding nitrogen adsorption-desorption isotherm and pore size distribution curve are presented to further analyze the mesoporous structure of composite.The surface composition and element valence states of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite were investigated by using XPS.The polarization relaxation processes were analyzed according to the Debye theory which describes the relationship between e'and e".Besides the polarization loss,the contribution of the conduction loss plays an important role for the overall dielectric loss.The magnetization curve of Mn_(x)O_(y)/C@Fe_(3)O_(4) exhibits typical ferromagnetic behavior.The permittivity parameter(Co),defined as Co=u"(u)^(-2)f^(-1) determine the contribution of eddy current effect to magnetic loss.The tand values are all larger than those of tand,for the three samples,indicating that the loss capacity of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites is mainly derived from the dielectric loss.Although tand,is smaller,it plays an important role in improving the impedance matching of Mn_(x)O_(y)/C@Fe_(3)O_(4) composites.When the filler loading is 15 wt.%,the RL of sample S-1 is about-10.0 dB at the thickness of 1.5 mm with narrow EAB.As the filler loading increased to 20 wt.%,the RL of sample S-2 reached-62.0 dB at a thickness of 2.2 mm and the EAB was 6.4 GHz at a small thickness of 1.7 mm.When the filler loading is further increased to 25 wt.%,the microwave absorption performance of sample S3 decreased significantly with a little region of RL<-10.0 dB at the thickness of 5.0 mm.The values of[Zin/Zol of the three samples at thicknesses of 1.5-5.0 mm were calculated.Due to good impedance matching of S-2,the incident EMW can enter the material and then can be dissipated through dipole polarization loss,interface polarization loss,conduction loss,eddy current loss and natural ferromagnetic resonance loss.[Conclusions]1D Mn_(x)O_(y)/C@Fe_(3)O_(4) was synthesized via a process involving the coating of polydopamine,adsorption of Fe(ll)salts and heat treatment,using MnO_(2) nanowires as templates.The multi-component heterostructure of the Mn_(x)O_(y)/C@Fe_(3)O_(4) composite(Mn_(3)O_(4),MnO,Fe_(3)O_(4),and C)enhances the interfacial interactions between the different phases,providing increased interface polarization loss under the action of an alternating electromagnetic field.The numerous defects and terminal groups in the mesoporous carbon provide abundant dipole polarization centers.Additionally,the presence of mesopores reduces the weight of the material while increasing the multiple scattering losses of the electromagnetic waves within the material.The ID carbon structure in the matrix forms a conductive network between adjacent fibers,facilitating electron migration and transition,thereby enhancing conductive loss.The incorporation of magnetic Fe_(3)O_(4) nanoparticles introduces eddy current loss and natural ferromagnetic resonance loss,thus increasing magnetic loss.Moreover,the synergistic effect between dielectric and magnetic losses improves the impedance matching of the material,leading to excellent EMW absorption performance.
文摘Broadband near-infrared(NIR)luminescent materials have shown great promise in applications such as optical communication,biomedicine,and optoelectronic devices.However,the current research is focused on phos⁃phors and glasses,and it is important to develop broadband NIR luminescent nanomaterials.Here,we report an erbi⁃um-sensitized core-shell nanocrystal design for broadband NIR emission.Based on the structural design with suitable dopings of Tm^(3+)and Ho^(3+),the broadband NIR emission covering 1.5-2.1μm region is achieved under 980 nm and 808 nm excitations.Moreover,the emission intensity is further enhanced by introducing Yb^(3+)and Nd^(3+)into the sam⁃ple,respectively,and the energy transfer processes between them are systematically discussed.Our results present a novel approach for developing broadband NIR luminescent materials and devices.
文摘A Yb:CaGd_(0.33)Y_(0.625)AlO_(4)(Yb:CGYA)laser crystal of high optical quality has been successfully synthesized via the Czochralski method.The introduction of Gd^(3+)ions preserves the original structure and efficiently generates inhomogeneous broadening of the Yb^(3+)ion emission spectra.The fluorescence emission peak wavelength of the Yb:CGYA crystal is 1053 nm,and the corresponding measured full width at halfmaximum is 93 nm.A tunable laser output ranging from 1017 nm to 1073 nm is achieved by using a birefringent filter,which represents the broadest tuning range reported in a short cavity to date.The compact laser offers significant advantages for its applications around the 1μm wavelength band.
文摘A millimeter-wave (mmW) broadband dual circularly polarized (dual-CP) antenna with high port isolation is proposed in this paper. The dual-CP performance is realized based on the symmetrical septum circular polarizer based on the gap waveguide (GWG) technology. Two sets of symmetrical septum circular polarizers are used for common aperture combination,achieving the broadband dual-CP characteristics. Taking advantage of GWG structure without good electrical contact, the antenna can also be fabricated and assembled easily in the mmW band. The principle analysis of the antenna is given, and the antenna is simulated and fabricated. The measured results show that the bandwidth for S11lower than-10.7 dB and the axial ratio (AR) lower than 2.90 dB in 75-110 GHz, with realative bandwidth of 38%. Over the frequency band, the gain is higher than 9.16 dBic, and the dual-CP port isolation is greater than32 dB. The proposed antenna with dual-CP and highly isolated in a wide bandwidth range has broad application prospects in the field of mmW communication.
基金supported by the National Nature Science Foundation of China (60472101)President Award of ChineseAcademy of Sciences(O729031511).
文摘Adaptive broadband beamforraing is a key issue in array applications. The adaptive broadband beamformer with tapped delay line （TDL） structure for nonuniform linear array （NLA） is designed according to the rule of minimizing the beamformer＇s output power while keeping the distortionless response （DR） in the direction of desired signal and keeping the constant beamwidth （CB） with the prescribed sidelobe level over the whole operating band. This kind of beamforming problem can be solved with the interior-point method after being converted to the form of standard second order cone programming （SOCP）. The computer simulations are presented which illustrate the effectiveness of our beamformer.
文摘In modern active and passive sonar systems, broadband beamforming for acoustic arrays is widely used to suppress unwanted interference and to detect target signals of interest. A broadband low sidelobe beamforming scheme in time domain is proposed in this paper. The first step of this scheme is to delay the outputs of each element in the acoustic array by a tapped-delay-line (TDL) to accomplish the integer part of the time delay need to form a beam. Then, finite impulse response (FIR) digital filters are used to implement the fractional part of the time delay. The weighting coefficients for all array elements at different frequencies to realize the low sidelobe beams are also implemented with the FIR digital filters. Finally, the outputs of the digital filters are summed up to yield the time domain beam output. The design of low sidelobe beam pattern and that of the FIR digital filters are two crucial technical issues in this beamforming procedure. The low sidelobe beams of each sub-band are designed using the optimized beam synthesis approach based on the principle of MVDR beamforming. An improved adaptive approach are used for the design of FIR digital filters, and the design requirements of these filters were specified by the weights of low sidelobe beams of each sub-band over the broad frequency band. Results of computer simulation for a twelve-element arc array show that the beamforming scheme is very effective in forming low sidelobe broadband beam.
基金National Natural Science Foundation of China(Grant Nos.51821003,52175524,61704158)the Natural Science Foundation of Shanxi Province(Grant No.202103021224206)Shanxi"1331 Project"Key Subjects Construction to provide fund for conducting experiments。
文摘In order to suppress the low-frequency ultrasound vibration in the broadband range of 20 k Hz—100 k Hz,this paper proposes and discusses an acoustic metamaterial with low-frequency ultrasound vibration attenuation properties,which is configured by hybrid arc and sharp-angle convergent star-shaped lattices.The effect of the dispersion relation and the bandgap characteristic for the scatterers in star-shaped are simulated and analyzed.The target bandgap width is extended by optimizing the geometry parameters of arc and sharp-angle convergent lattices.The proposed metamaterial configured by optimized hybrid lattices exhibits remarkable broad bandgap characteristics by bandgap complementarity,and the simulation results verify a 99%vibration attenuation amplitude can be obtained in the frequency of20 k Hz—100 k Hz.After the fabrication of the proposed hybrid configurational star-shaped metamaterial by 3D printing technique,the transmission loss experiments are performed,and the experimental results indicate that the fabricated metamaterial has the characteristics of broadband vibration attenuation and an amplitude greater than 85%attenuation for the target frequency.These results demonstrate that the hybrid configurational star-shaped metamaterials can effectively widen the bandgap and realize high efficiency attenuation,which has capability for the vibration attenuation in the application of highprecise equipment.
基金Supported by the National Natural Science Foundation of China( 61974104)。
文摘Microstrip transmission lines connecting to the millimeter wave radar chip and antenna significantly affect the radiation efficiency and bandwidth of the antenna.Here,a wideband non-uniform wavy microstrip line for complex impedance in automotive radar frequency range is proposed.Unlike the gradient transmission line,the wavy structure is composed of periodically semi-circular segments.By adjusting the radius of the semi-circular,the surface current is varied and concentrated on the semi-circular segments,allowing a wider tunability range of the resonant frequency.The results reveal that the bandwidth of the loaded wavy transmission line antenna improves to 9.37 GHz,which is 5.81 GHz wider than that of the loaded gradient line.The gain and the half power beam width of the loaded antenna are about 14.69 dB and 9.58°,respectively.The proposed non-uniform microstrip line scheme may open up a route for realizing wideband millimeter-wave automotive radar applications.
